M18BPD Product Manual

M18BPD Product Manual
OPERATOR'S MANUAL
Cat. No.
M18BDD-0
M18BPD-0
M18™ CORDLESS 1/2" DRILL/DRIVER AND HAMMER DRILL/DRIVER
To reduce the risk of injury, user must read and understand operator's manual.
General POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury. save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
work area SAFETY
attached to a rotating part of the power tool may
result in personal injury.
•Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
•If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
•Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
electrical safety
•Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
•If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
POWER Tool use and care
•Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
•Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
•Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
•Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
personal safety
•Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
•Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
•Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
Battery Tool use and care
2
•Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
•Use power tools only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
• Maintain labels and nameplates. These carry
important information.
•WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•lead from lead-based paint
•crystalline silica from bricks and cement and other
masonry products, and
•arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
•Whenbattery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery termi•Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs,
with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
SERVICE
•Have your power tool serviced by a
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
•Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
•Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
•Hold power tool by insulated gripping surfaces, when performing an operation where
FUNCTIONAL DESCRIPTION
SYMBOLOGY
Volts
3
Direct Current
4
5
6
No Load Revolutions per
Minute (RPM)
Blows per Minute Under Load
(BPM)
1. Trigger
2
2. LED
1
3. Keyless chuck
4. Torque selector collar
5. Application selector collar
(M18BPD-0)
6. Speed selector
7. Control switch
SPECIFICATIONS
7
Wood
Volts
Flat Auger Hole Screws
Cat. No. DC No Load RPM
BPM
Steel
Bit
Bit
Saw
(dia.) Masonry
M18BDD-0
18
Low 0 - 450
-13 mm 29 mm 25 mm 54 mm 6mm
-High 0 - 1,800
-M18BPD-0
18
Low 0 - 450
Low 0 - 7200 13 mm 29 mm 25 mm 54 mm 6mm
16 mm
High 0 - 1800 High 0 - 28,800
3
Selecting Drill or Drive Action
(Cat. No. M18BDD-0)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until
the desired clutch setting appears in line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different
materials and to prevent damage
to the screw or tool.
ASSEMBLY
WARNING Recharge only with the
for the battery. For
charger
charging instructions, read the operator’s
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
OPERATION
Selecting Hammer, Drill or Drive Action
(Cat. No. M18BPD-0)
1. To use the hammer-drilling
mode, rotate the application
selector collar until the hammer
symbol
appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
NOTE: The number selected on
the torque selector collar has no effect on operation of the drill in hammer mode.
NOTE: When using carbide bits, do not use water to settle dust. Do not attempt to drill through
steel reinforcing rods. This will damage the
carbide bits.
2. To use the drilling only mode,
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
WARNING
Always remove battery
pack before changing or removing accessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Installing Bits
Always remove the battery before inserting or
removing bits. Select the proper style and size bit
for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 16 mm (1/16") off of the
bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counterclockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck’s operation.
4
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See “Applications” for recommended speeds under various conditions.
1.For Low speed, push the speed selector to
display “1”.
2.For High speed, push the speed selector to
display “2”.
3.To use the driving screws
mode rotate the application
selector collar until the drive
symbol
appears in line with
the arrow. Then rotate the torque
selector collar until the desired
clutch setting appears in line with
the arrow.
The adjustable clutch, when properly adjusted,
will slip at a preset torque to prevent driving the
screw too deep into different materials and to
prevent damage to the screw or tool.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mechanism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow
the motor to come to a complete stop before using
the control switch.
For forward (clockwise)
rotation, push in the conReverse
trol switch from the right Forward
side of the tool. Check
Lock
the direction of rotation
Push to
CENTER
before use.
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while
the control switch is in the center locked position.
Always lock the trigger or remove the battery
pack before performing maintenance, changing
accessories, storing the tool and any time the tool
is not in use.
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
Cat. No. M18BDD-0
Clutch
Applications
Setting in. lbs
1-5
15-30 Small screws in softwood.
6-10
11-15
16-17
32-40 Medium screws in softwood or small
screws in hardwood.
43-50
Large screws in softwoods. Medium
55-100 screws in hardwood or large screws in
hardwood with pilot hole.
Cat. No. M18BPD-0
Clutch
Applications
Setting in. lbs
1-3
28-30 Small screws in softwood.
4-6
7-9
10-13
14-17
18
31-33
Medium screws in softwood or small
34-39 screws in hardwood.
41-47
49-55 Large screws in softwoods. Medium
screws in hardwood or large screws in
57 hardwood with pilot hole.
WARNING To reduce the risk of injury,
always hold or brace securely.
Starting, Stopping and Controlling Speed
1.To start the tool, grasp the handles firmly and
pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2.To vary the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
3.To stop the tool, release the trigger. Make sure
the bit comes to a complete stop before laying
the tool down.
NOTE: Because the settings shown in the table are only
a guide, use a piece of scrap material to test the different
clutch settings before driving screws into the workpiece.
Drilling
Place the bit on the work surface and apply firm
pressure before starting. Too much pressure will
slow the bit and reduce drilling efficiency. Too little
pressure will cause the bit to slide over the work
area and dull the point of the bit.
If the tool begins to stall, reduce pressure slightly
to allow the bit to regain speed. If the bit binds,
reverse the motor to free the bit from the workpiece.
5
APPLICATIONS
MAINTENANCE
WARNING To reduce the risk of electric shock, check work area for hidden pipes
and wires before drilling or driving screws.
WARNING To reduce the risk of injury,
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble the tool, battery pack or charger.
Contact a MILWAUKEE ® service facility for
ALL repairs.
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the
drill-only operating mode.
Start the drill slowly, gradually increasing speed
as you drill. When drilling into wood, use wood
augers or twist drill bits. Always use sharp bits.
When using twist drill bits, pull the bit out of the
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to
your local authorized MILWAUKEE® dealer or
service centre for:
• Lubrication
• Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to your local authorized MILWAUKEE® dealer or
service centre for repairs.
reduce the chance of splintering, back work with a
piece of scrap wood. Select low speeds for plastics
with a low melting point.
Drilling in Metal
When drilling in metal, select the
drill-only
operating mode. Use high speed steel twist drills
or hole saws. Use a center punch to start the hole.
Lubricate drill bits with cutting oil when drilling in
iron or steel. Use a coolant when drilling in nonferrous metals such as copper, brass or aluminum.
Back the material to prevent binding and distortion
on breakthrough.
Drilling in Masonry
When drilling in masonry, select the
hammer
drill operating mode. Use high speed carbide-tipped
bits. Drilling soft masonry materials such as cinder
block requires little pressure. Hard materials like
concrete require more pressure. A smooth, even
WARNING To reduce the risk of personal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
inside them.
a liquid to
let the bit spin in the hole without cutting. Do not
use water to settle dust or to cool bit. Both actions
will damage the carbide.
Cleaning
Clean dust and debris from charger and tool vents.
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use
Driving Screws and Nut Running
Drill a pilot hole when driving screws into thick or
hard materials. Select the
driving screws mode.
Set the torque selector collar to the proper position
and set the speed to low. Use the proper style and
size screwdriver bit for the type of screw you are
using. With the screwdriver bit in the screw, place
pressure before pulling the trigger. Screws can be
removed by reversing the motor.
Repairs
For repairs, return the tool, battery pack and
charger to the nearest service center.
Overloading
Continuous overloading may cause permanent
damage to tool or battery pack.
ACCESSORIES
WARNING Always remove battery pack before changing or removing accessories.
Only use accessories specifically recommended for this tool. Others may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE® accessories catalogue or go
online to www.milwa ukeetools.com.au or www.milwaukeetools.co.nz. To obtain a product
catalogue, please contact your local authorized MILWAUKEE® dealer or service centre.
6
WARRANTY - AUSTRALIA and NEW ZEALAND
Please refer to the Techtronic Industries Pty. Ltd. Warranty Terms and Conditions for
MILWAUKEE® products and accessories document supplied with tool. This warranty applies only
to product purchased from an authorised MILWAUKEE® dealer in Australia or New Zealand.
AUSTRALIA AND NEW ZEALAND
MILWAUKEE ® Service
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy
Duty®. Your satisfaction with our products is very important to us! If you encounter any problems
with the operation of this tool, please contact your authorised MILWAUKEE® dealer or service
centre.
7
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Doncaster, Victoria, Australia, 3108
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mangere, Auckland, New Zealand, 2022
Professionally made in China for Milwaukee Electric Tool Corporation
Printed in China
961016050-01(A)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement