Slip-On (2010)
Installation Instructions
V.A.L.E.
2010 Suzuki
TM
V a r i a b l e
RMZ250
A x i s
L o c k i n g
E x h a u s t
1.
Make sure the bike is completely cool before starting
the installation. Make sure the bike is secure on a
centerstand or ideally a service lift.
2.
Remove right side plastic.
3.
Remove upper muffler mounting bolt.
4.
Remove lower muffler mounting bolt.
5.
Remove muffler assembly.
6.
Use the 4 (four) 6x20mm bolts and 6mm split lock
washers to loosely attach the X-Lite™ ring to muffler
inlet.
X-Ring
Slip-On V.A.L.E.™ Exhaust System
Part # 005-2670406V / 005-2670407V
Slip Tube
Muffler Inlet
V.A.L.E.™ Assembly Detail
Parts List
Qty.
Description
Part Number
1
1
1
2
4
4
1
1
1
Muffler Canister
S-Bend for Slip-on System HARDWARE KIT
X-Ring (half)
6mm Split Lock Washer
6x20mm Socket Head Cap Screw
5mm Long Handle Ball end hex key
T20 Torx Hex Key
TBR Sticker Kit
Varies
005-26704S
005-267-3
005-7-2-3
005-WL6
005-SH620
005-9-18610
005-9-15820
015-10212
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
7.
Slip S-bend tube of V.A.L.E.™muffler assembly into
head pipe. Use OEM bolt to loosely attach upper muffler
mount and the OEM bolt to the lower mount.
8.
Making sure that the V.A.L.E.™assembly is oriented
correctly, securely tighten upper muffler mounting bolt.
9.
Securely tighten the 4 (four) 6x20mm hex head bolts of
the V.A.L.E.™assembly.
10. Securely tighten the lower muffler mounting bolt.
11. Reinstall side panel.
12. Double check to make sure that all hardware is
tightened.
13. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off.
Check for gaps or leaks. After 50 to 100 miles, recheck
all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
V.A.L.E.
2010 Suzuki
TM
V a r i a b l e
RMZ250
A x i s
L o c k i n g
E x h a u s t
Slip-On V.A.L.E.™ Exhaust System
Part # 005-2670406V / 005-2670407V
Parts List
Qty.
Description
Part Number
1
1
1
2
4
4
1
1
1
Muffler Canister
S-Bend for Slip-on System HARDWARE KIT
X-Ring (half)
6mm Split Lock Washer
6x20mm Socket Head Cap Screw
5mm Long Handle Ball end hex key
T20 Torx Hex Key
TBR Sticker Kit
Varies
005-26704S
005-267-3
005-7-2-3
005-WL6
005-SH620
005-9-18610
005-9-15820
015-10212
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement