10 /20 /26 03

INSTALLATION AND
OPERATION INSTRUCTIONS
BRENTWOOD™
EPA Wood-Burning Fireplaces
P/N 850,039M REV. H 05/2010
TM
MODEL
BRENTWOOD SP
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and
understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of the fireplace system, including
but not limited to the fireplace, chimney components and accessories,
may void the warranty, listings and approvals of this system and could
result in an unsafe and potentially dangerous installation.
Lennox Hearth Products wood-burning fireplaces are designed for use
as a supplemental heater. They are not intended for continuous use
as a primary heat source.
Fireplace, also for use in mobile or
manufactured homes with solid fuel only.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNINGS
WARNINGS
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
• If small children are present in the home, it
is recommended that this appliance be fitted
with a firescreen kit. See Page 20 for ordering
information.
• The fireplace cannot be operated without a door
or firescreen. Consult your dealer to select the
correct door or firescreen.
• Important! To assure proper alignment of glass
doors: Install this fireplace in a square and
plumb condition, using shims as necessary at
sides and/or bottom.
• Install the fireplace only as described in these
instructions.
Listed to standards:
ULC-S610 & UL-127
Report No. 3011202
EPA Cert. No. 537
PIBRENTW REV. 12 MAY 2010
IMPORTANT! GENERAL SAFETY
PRECAUTIONS. READ AND
UNDERSTAND THESE SAFETY
RULES BEFORE YOUR FIRST FIRE.
WARNING
THE FIREPLACE MUST BE OPERATED WITH THE DOOR FULLY
OPENED OR DOOR FULLY CLOSED.
IF THE DOORS ARE LEFT PARTLY
OPENED, GAS AND FLAME MAY BE
DRAWN OUT OF THE FIREPLACE
OPENING, CREATING RISKS OF
BOTH FIRE AND SMOKE. IF THE
UNIT IS OPERATED WITH THE
DOORS FULLY OPENED, THE
OPTIONAL FIRE SCREEN MUST
BE USED.
WARNING
NEVER use gasoline, gasolinetype lantern fuel, kerosene,
charcoal lighter fluid, naphtha,
engine oil or similar liquids to
start or “freshen up” a fire in this
fireplace. Keep any flammable
liquids a safe distance from the
fireplace at all times.
WARNING
THIS FIREPLACE HAS NOT BEEN
TESTED WITH AN UNVENTED
GAS LOGS OR A FIREPLACE
INSERT. TO REDUCE RISK
OF FIRE OR INJURY, DO NOT
INSTALL AN UNVENTED GAS
LOG SET OR FIREPLACE INSERT
OR OTHER PRODUCTS NOT
SPECIFIED FOR USE WITH THIS
FIREPLACE.
WARNING
Never leave your fireplace unattended while it is burning.
WARNING
To avoid the risk of damaging
fireplace materials and increasing the risk of fire, do not use the
fireplace to cook or warm food.
2
WARNING
Use care when selecting window
treatments for windows located
near the fireplace. Avoid using
combustible flowing window
treatments such as curtains on
nearby windows that are of sufficient length to be blown in front
of an open flame when the window
is opened. Keep any combustible
furniture, materials or decorative
pillows at least 48" (1219 mm)
from the front fireplace opening.
WARNING
Never modify or alter your fireplace
system in any way. To do so may
create a potential fire hazard and
void the limited warranty, listings
and approvals of this system.
IMPORTANT
When burning wood, use SOLID
NATURAL DRY WELL-SEASONED
WOOD ONLY. Hardwoods are recommended (soft woods tend to burn
very quickly).
• DO NOT burn treated wood,
charcoal, coal, trash, cardboard,
driftwood, woods dipped in tar,
Christmas tree greens, pitch, pine
tar, creosote, chemical chimney
cleaners, flame colorants, polystyrene packaging, wood products with synthetic binders (i.e.
plywood). Plywood, lumber and
other misc. materials can produce
abnormally high temperatures,
sputtering and smoking fires and
may contain hazardous chemicals
to treat insects and fungus.
• Burning unapproved fuels can
produce excessive temperatures,
beyond the design capabilities
of the fireplace and may produce
excess sparks or may contain
hazardous chemicals. Burning
unapproved fuels can result in
a chimney fire, a house fire,
personal injury, death or loss of
property.
WARNING
Never leave children unattended
when there is a fire burning in the
fireplace.
WARNING
Always ensure that the air inlet to
the fireplace is free from debris
and any other obstructions that
can block the entrance of air.
IMPORTANT
WHEN INSTALLED IN A MOBILE OR
MANUFACTURED HOME:
• Mobile or manufactured home
installations must be installed in
accordance with the requirements
of the Department of Housing and
Urban Development (HUD) “Mobile
Home Construction and Safety standards” for US or Canada Mortgage
and Housing Corporation (CMHC)
for Canada.
• The fireplace must be fastened to
the floor by unfolding and screwing
the small tabs on both sides at the
bottom of the fireplace.
• It is necessary to have access
openings, for inspection purpose
only, into built-in enclosures surrounding the fireplace installation.
Such openings to require a household tool for access.
• The vapor barrier of the mobile
home shall be as close as possible
of the location where the chimney
assembly penetrates the ceiling
and roof structure with no interference to the required clearance to
combustible material.
• When the mobile or manufactured
home has a flat roof, the Attic Radiation Shield must be installed from
below going through the roof (See
Figures 19b and 19d).
• Warning: Do not install in a
sleeping room
WARNING
Neither the manufacturer nor the
seller warrants “smoke free”
operation nor are we responsible for inadequate system draft
caused by mechanical systems,
general construction conditions,
inadequate chimney heights,
adverse wind conditions and/or
unusual environmental factors or
conditions beyond our control.
Congratulations!
When you purchased your new wood fireplace, you joined the ranks of thousands of
individuals whose answer to their home heating needs reflects their concern for aesthetics,
efficiency and our environment. We extend our continued support to help you achieve
the maximum benefit and enjoyment available from your new wood fireplace.
Thank you for selecting a Lennox Hearth Products wood fireplace as the answer to your
home supplemental heating needs.
TABLE OF CONTENTS
Safety Rules and Specifications for
Mobile or Manufactured
Home Installation..........................Page 2
Introduction.......................................Page 3
Parts Required ..................................Page 3
Optional Equipment............................Page 3
Operating The Fireplace.....................Page 3
Fuel....................................................Page 3
Combustion Control . ........................Page 4
Refueling For Best Performance........Page 4
Smoking – Causes And
Troubleshooting...............................Page 4
Important Cautions............................Page 5
Maintaining Your
Brentwood Fireplace........................Page 5
Chimney Maintenance........................Page 5
Dealing With A Chimney Fire..............Page 5
Finish Door Casing Care.....................Page 5
Disposing of Ashes............................Page 5
Refractory Installation........................Page 6
Door Installation................................Page 6
Door Adjustment................................Page 6
Glass Care - Replacement..................Page 7
Glass Care - Cleaning.........................Page 7
Gasket Replacement .........................Page 7
Fireplace Installation .........................Page 7
Locating The Brentwood....................Page 7
Framing, Facing And Mantel...............Page 8
Hearth Extension Requirements . ......Page 8
Cold Climate Installations...................Page 8
Fireplace and Framing Dimensions....Page 9
Nailing Flanges...................................Page 10
Facing / Mantel...................................Page 10
Hot Air Ducting Installation ...............Page 11
Gravity Kit..........................................Page 11
Outside Air Kit . .................................Page 12
Chimney System................................Page 13
Chimney Installation Notes................Page 13
Chimney Installation Instructions.......Page 14
Offset Chimney Installation................Page 15
Angled Wall Radiation Shield.............Page 17
Chimney Support Installation.............Page 18
Chimney Chase And
Multiple Terminations......................Page 18
Chimney Adaptor...............................Page 18
Masonry Application Instructions......Page 19
Installation Accessories.....................Page 20
Chimney Components Lists...............Page 21
Replacement Parts.............................Page 23
Specifications.....................................Page 23
Clearances.........................................Page 23
Product Reference Information..........Page 24
THE FIREPLACE
INTRODUCTION
The Brentwood wood-burning fireplace is an
energy efficient, heat circulating, closed combustion fireplace. You will receive a lifetime
of comfort and enjoyment from your fireplace
provided it is installed, maintained and operated properly.
• Please read these instructions and retain
this manual for future reference.
• Before beginning the fireplace installation,
consult the local authorities to obtain your
building permit and check your local building
codes. Install the fireplace only as described
in these instructions and using only Lennox
Hearth Products components.
• This fireplace has been tested for CAN/ULC
S610-M87 and ANSI/UL 127 under report
number 3011202. It has also been tested
for EPA 40 C.F.R Part 60, section 60.532(b).
Certificate number 537.
• The Brentwood fireplace is not intended for
use with a gas log set. Do not use a fireplace
insert or any other product with this fireplace
unless it is specified by Lennox for use with this
appliance. Failure to follow these instructions
will void the certification and the warranty of
the fireplace and may result in an unsafe
installation.
• Lennox Hearth Products wood fireplaces are
designed for use as a supplemental heater.
They are not intended for continuous use as
a primary heat source.
Parts Required
Fireplace Model Brentwood SP
• 6” diameter chimney - model ASHT, S-2100+,
HT6000+, HT6103+ or AC manufactured by Security Chimneys International only, including:
-Chimney lengths
-Elbows (where necessary)
- Associated components as per these
installation instructions
• ..Decorative Cast Iron Door - Required
...(Order Separately)
- Available in black, gold or brushed nickel
(see Page 20)
• ..Outside air kit (Included w/Fireplace)
OPTIONAL EQUIPMENT
• .Additional Equipment (optional)
-.AC Chimney Adaptor
(required if using AC Chimney)
-.AC chimney outside air kit
- Gravity venting system
-.Panel for clean face option
(only with gravity venting system)
- Forced Air Kit u
-.Rigid firescreen
-.Fireplace Blower Kit
- Blower Speed Control
u
Not tested under EPA certification. If in-
stalled, this appliance no longer qualifies
for EPA certification.
OPERATING THE fireplace
Fuel
USE SOLID NATURAL WOOD FUEL ONLY. The
Brentwood fireplace is designed to work best
when fueled with dry seasoned natural wood
only. Hardwoods are preferred to softwoods
since the energy content of wood is relative to
its density. Hardwoods will result in a longer
burning fire and less frequent refueling. A
moisture content of 15% to 20% (seasoned)
is recommended. Wood that has been cut and
split and let to dry under a cover for a period
of one year will usually meet that criteria. The
required drying time will vary depending on the
climate. Wood that is packed tight together will
take longer to dry. Seasoned wood is darker in
color than wet wood and will have visible cracks
in the grain on the ends. Excessively wet wood
will be difficult to burn and will result in lower
efficiency, increased creosoting and deposits on
the glass and in the chimney. Excessively dry
wood will burn well but will also have higher
emissions and shorter burning time.
Do not burn scrap or garbage, treated wood or
wood such as driftwood from the ocean which
has been exposed to salt or other chemicals.
Salt or chemicals can corrode the firebox and
chimney. Do not burn large amounts of paper,
cardboard, Christmas tree branches or building
construction materials. Intense firing with these
materials may overheat the fireplace, causing
damage to the unit, a fire or even possibly igniting a chimney fire if the chimney is creosoted.
Burning unapproved fuel, resulting in excessive
pollutants being emitted, may be prohibited and
subject to a fine or other penalty by the authority
having jurisdiction in your area.
Processed firelogs can be used. Use only firelogs that have been evaluated for the application
of fireplace and refer to firelog warnings and
caution markings on packaging prior to use.
First Fires
Before using the fireplace make sure to remove
the plastic wrapping and EPA label on plated
door. Remove any glue residue left by the
label using mild soap.
The first five or six fires should be small fires of
short duration (about 30 to 60 minutes). This
will help cure the refractory bricks. During the
first few fires of this appliance there may be
some odor and smoke due to the curing of the
paint, dust accumulation and burning off of
lubricants used in the manufacturing process.
It may set off a smoke alarm located in the same
room. For this reason the room should be well
ventilated for the first few fires.
3
WARNING
Be careful adding wood fuel to the
fire or handling fireplace tools such
as shovels, tongs or pokers.
WARNING
The bottom refractory can be
cracked by excessive abuse such
as tossing heavy logs onto the
grate or gouging with fireplace
tools. Exercise caution when
adding wood to your fireplace.
combustion air control should be opened before
opening the door to minimize the possibility of
back draft coming into the room.
Accelerated Combustion
The maximum heat output for the Brentwood™
fireplace is achieved by burning with the door
closed and the combustion air opened and
pulled out. By this method, the Brentwood
fireplace can produce up to 55,000 BTU of
heat per hour. However, it will be necessary
to reload with wood every one or two hours.
This is the least efficient method of burning the
Brentwood fireplace.
Push to Close
Air Boost
Building a Fire
(starting and maintaining a fire)
To start a fire, place several crumpled up balls of
newspaper in the firebox. Place small dry pieces
of kindling on top of the paper, criss-crossing
the kindling so that there are air spaces in between. Keep the fuel far back enough so that air
can get underneath. Open the air controls fully
and light the newspaper. Once the newspaper
and the kindling is well ignited, close the door.
Once the kindling fire is well established, cord
wood can be added (see Primary Air Combustion Control section for proper operation of the
air controls).
The unit will burn best with 2-3 pieces of cord
wood spaced 1 to 2 inches apart and allowing
air to get under the fuel. Criss-crossing or arranging the fuel so that air can get underneath,
will help the fire to get started easily. The unit
should be operated with the air control fully
open long enough to get the cord wood well
ignited.
COMBUSTION CONTROLS
Primary Air and Air Boost Controls
There is no flue damper in the Brentwood™
fireplace. As is common with air tight stoves,
the combustion air control sets the flow of air
entering the firebox. This allows for a more
precise control of the fire. The combustion air
control is located below the door on the left side.
The main source of air (primary air) entering
the firebox can be diminished by moving the
air combustion control from left to right. The
primary air is fully opened when the air control
is completely moved to the left. The air control
device can also be used to add an extra boost of
air especially during fire start up and reloading
of the unit. Pulling the air combustion control
will induce an air boost at the base of the fire
allowing an easier fire start up. When the fire is
well established, the control can be pushed in
to shut down the air boost allowing for a longer
burn time. The combustion air control should
be in the closed position (primary air and air
boost) when the fireplace is not in use. This
will minimize air leakage up the chimney. The
4
Slow
Pull to
Open
Air Boost
Medium
Accelerated
Figure 1
Use caution when firing with the combustion
air control wide open. Only burn cord wood in
this manner. Small dry pieces of softwood and
construction scraps will burn very intensely using this method and may damage the firebox.
Medium Combustion
This is the recommended mode of operating
the Brentwood fireplace and should be the
one normally used since it will deposit the
least amount of creosote on the glass and
in the chimney. The combustion air control
must be 3/4 closed and pushed in to close the
air boost. The precise setting will depend on
many factors, including chimney length and the
moisture content of the wood.
For instance, a long chimney will necessitate
closing the damper more. To obtain the proper
combustion, close the damper completely, then
open it about 1/4” to 1/2”. Three medium size
pieces of wood should be burning on a bed of
hot coals. The heat output will be approximately
30,000 BTU per hour and the loading time will
be about every 3-4 hours. Softwoods may be
burned using this method but the time will be
substantially reduced.
Slow Combustion
When the air combustion control is completely
closed, the fireplace is in a slow combustion
phase. If the hearth is hot enough, slow combustion will not extinguish the fire, but there will be
a noticeable change in the flame pattern. The
flames will be slow and may appear dirty if the
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
wood is too wet (moisture content of 20% and
more). Do not allow the wood to burn without
flame, since this will produce excessive creosote
in the unit.
Creosote may accumulate on the glass door.
This method of burning should be used only
after operating the Brentwood fireplace with
the air control opened to produce a hot fire for
about an hour or at medium pace for at least
three (3) hours. Slow combustion can be used
at night in order to reduce the heat output and
to prolong the burn. The loading time will be
between 6-8 hours.
REFUELING FOR BEST PERFORMANCE
The Brentwood fireplace will operate best if
attention is given to operating the unit with the
damper fully opened after refueling in order
to bring the firebox and the chimney system
up to their optimum operating temperature.
Combustion efficiency is relative to firebox
temperature. A temperature of 500º C (932º F)
and up, with a visible flame, in the upper part
of the firebox indicates a maximum efficiency.
To obtain this temperature, the fireplace must
be operated with the primary air and air boost
controls fully opened during 10 to 20 minutes
after reloading, depending on the heat and on
the moisture content of the wood.
Once you have reached the desired temperature,
the air boost can be closed and the primary air
set to a medium setting. You know you have
reached the desired temperature when, closing
the primary air control, you can see a flame
at the top of the firebox. The benefit of this
technique will be cleaner glass, less creosoting,
greater efficiency and the most pleasing fire for
your enjoyment. If your fireplace is equipped
with a forced air system, make sure the central
blower is turned off during reloading to avoid
smoking problems.
SMOKING –
CAUSES AND TROUBLESHOOTING
To reduce the likelihood of smoking when opening the door, set the combustion air controls to
the left before opening the door. Your fireplace
has been designed and tested to provide smoke
free operation. Occasionally, there may be a
small amount of smoking upon lighting the fire,
until the chimney heats up but this should not
continue. If the fireplace continues to smoke it
is probably for one of the following reasons:
A. Negative pressure in the house
As the fire burns, air goes up the chimney.
This air must be replaced through leakage
into the house or through the outside air duct.
When operating the Brentwood fireplace,
open a nearby window temporarily to check if
there is adequate replacement air supply.
B.Blowers operating (e.g.: range hood)
- These blowers draw air out of the house
and may actually cause a negative pressure
in the house. Turn off all blowers and open
a nearby window to determine if this is the
cause of the problem.
C.Wet wood- Wet or tarred wood will smoulder
and smoke instead of burn properly. Your
dealer can help you determine if you have
properly seasoned wood for burning.
D.Dirty or blocked chimney- Check to make
sure the chimney is clear and clean. If dirty
call a certified chimney sweep or use a
properly sized chimney brush to clean.
E. Chimney not long enough- The minimum
chimney height is twelve (12) feet (3.7 m) not
including the fireplace height. The chimney
must extend at least three (3) feet (915 mm)
above its point of contact with the roof and
at least two (2) feet (610 mm) higher than
any roof or wall within ten (10) feet (3 m) of
it. When installed with offsets, the minimum
chimney height is fifteen (15) feet. Additional
height will increase draft and will decrease
the tendency to smoke.
F. Poor chimney draft- With no fire, there should
be sufficient draft to exhaust cigarette smoke
introduced under the baffle. Chimneys installed
against an outside wall without protection may
generate back draft problems which will cause
start-up problems. To prevent this, open a
nearby window, roll up a piece of paper and
light it. Then, hold it in the upper part of the
firebox to warm up the chimney. Wait until
the draft is sufficient, then start the fire.
G. Blower for forced air kit operating - Make
sure that the blower is at the “off” position when
you open the fireplace door for reloading.
IMPORTANT CAUTIONS
A.Do not block the hot air vents to the fireplace as this will cause the fireplace to
overheat.
B.Never use gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter fluid, or
similar liquids to start or ‘freshen up’ a fire
in this fireplace. Keep all such liquids well
away from the fireplace while it is in use.
C.Do not burn coal. The sulphur in coal will
corrode the firebox.
D.Do not burn driftwood which has been in the
ocean or salt water. The salt will corrode
the firebox and chimney.
E. Do not burn wood in the area in front of the
grate.
F. Do not abuse the unit by burning paper, or
cardboard or construction material such as
pressed wood, plywood or lumber. Wood
protectors, metallic paper, coal, plastic,
waste, sulphur and/or oil will damage the
fireplace.
G.Do not allow the wood to smoulder or burn
without flame, since this will produce
excessive creosote in the unit as well as
increased particulate emissions.
As a result, creosote residue accumulates on the
flue lining. When ignited this creosote makes
an extremely hot fire.
The chimney shall be inspected at least twice
a year during the heating season to determine
when a creosote buildup has occurred.
When creosote has accumulated it shall be
removed to reduce the risk of a chimney fire.
When the creosote accumulation is large, a
creosote fire in the chimney can damage the
chimney and overheat the surrounding wood
framing. Creosote formation in a chimney can
be minimized by making sure there is always
visible flame burning, avoid smouldering fires
and by proper refuelling techniques.
Chimney Maintenance
Regular chimney inspection and maintenance
combined with proper operation will prevent
chimney fires. Keep your chimney clean. Do not
allow more than 1/16” (1.6 mm) creosote build
up in your chimney. The amount of creosote will
depend on variables such as frequency of use
and type of fire. We recommend that you:
A.Initially inspect the chimney system weekly.
From this, you will learn how often it will be
necessary to clean your chimney.
B.Have your chimney cleaned by a qualified
chimney sweep. If you wish to clean it
yourself, we recommend using a stiff plastic
or non-metallic brush. If a metal brush is
used, its size should be slightly smaller than
the flue to avoid damaging the chimney. Do
not use a brush that will scratch the stainless
steel interior of the chimney.
C.Do not expect chemical cleaners to keep
your chimney clean. The rain cap can be
removed for inspection and/or cleaning of
the chimney.
Top Baffle Removal Prior to Cleaning The
Chimney
Before starting to clean your chimney, we
recommend that you remove the top baffle to
avoid creosote dust collection at the top of the
baffle. Follow these steps to set the top baffle
out of the way:
1. Remove the side refractory holder. They are
located at the top of the refractory.
2. Lift the front baffle.
3. Slide the back baffle under the front baffle.
You now have access to the chimney.
MAINTAINING YOUR FIREPLACE
Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar
and other organic vapors, which combine
with expelled moisture to form creosote. The
creosote vapors condense in the relatively cool
chimney flue of a slow-burning fire.
Figure 2a - Top Baffle Removal
Figure 2b - Top Baffle Removal
Dealing With a Chimney Fire
Regular chimney maintenance and inspection
can prevent chimney fires. If you have a chimney
fire, follow these steps:
1. Close the fireplace door and the combustion
air controls.
2. Alert your family of the possible danger.
3. If you require assistance, alert your fire
department.
4. If possible, use a dry chemical fire extinguisher, baking soda or sand to control the
fire. Do not use water as it may cause a
dangerous steam explosion.
5. Check outside to ensure that sparks and hot
embers coming out of the chimney are not
igniting the roof.
6. Do not use the fireplace again until your
chimney and fireplace have been inspected
by a qualified chimney sweep or a Fire
Department Inspector.
Finish Door Casing Care
Use a glass cleaner and a soft cloth to polish
the casing. Do not use abrasives such as steel
wool, steel pads or an abrasive polish for they
may scratch the casing’s finish.
DISPOSING OF ASHES
Note: For better performances, we recommend
leaving 1/2 inch of ashes in the firebox.
Remove ashes only when the fire is out and
the ashes are cold (24 to 48 hours after the fire
is out). Do not leave the ashes in the house
as they give off carbon monoxide and other
toxic gases.
WARNING
Disposal of Ashes: Ashes should
be placed in a metal container with
a tight fitting lid. The closed container of ashes should be placed
on a non-combustible floor or on
the ground well away from all
combustible materials, pending
final disposal. If the ashes are
disposed of by burial in soil or
otherwise locally dispersed, they
should be retained in the closed
container until all cinders have
thoroughly cooled.
5
REFRACTORY REPLACEMENT
The intense heat of the fire will normally cause
hairline cracks in the refractory. These cracks
can be minimized by proper curing as described
in “First Fires”. They will not normally diminish the effectiveness of the refractory. If large
cracks develop, then the refractory should be
replaced. To replace the refractory bricks, follow these steps:
1. Remove the front refractories
2. Remove the bottom refractory
3. Remove the left side refractory
4. Remove the right side refractory
5. Remove the back refractory
6. Remove the front ceramic baffle
7. Remove the rear ceramic baffle
To install the new refractories, follow the above
steps in reverse.
DOOR INSTALLATION
The door must be installed only when the installation of the Brentwood™ fireplace is completed.
All you have to do is fit the male part of the
hinge, already on the door, to the female part,
which is on the fireplace.
To remove the door, simply pull the door up
from the hinges.
7
5
4
1. Front Refractories
2. Bottom Refractory
3. Left Side Refractory
4. Right Side Refractory
5. Back Refractory
6. Front Ceramic Baffle
7. Rear Ceramic Baffle
3
2
Figure 3
The door adjustment has been set at the factory.
If the fit is still not perfect, you can adjust the
door using the hinge screws.
DOOR ADJUSTMENT
The door may need to be adjusted to be completely airtight. The gaskets’ air-tightness can be
adjusted using the adjustment screw located on
the right side of the fireplace facade (An Allen
key #1/8 – not supplied - will be necessary for
this adjustment).
Checking Door Seal - A one-inch strip of paper
may be used to perform a test of the integrity
of the door seal. Close the door on the paper in
at least eight points. It is normal to feel only a
slight amount of friction. The door gasket does
not need to be “tight” in all areas, since a small
amount of leakage is not hazardous or detrimental to the performance of your fireplace.
1
WARNINGS
• Use only a Lennox Hearth Products glass doors, specifically designed
for the Brentwood fireplace.
• The fireplace cannot be operated without door or firescreen. Consult
your dealer to select the correct replacement door or firescreen.
• Important! To assure proper alignment of glass doors: Install this
fireplace in a square and plumb condition, using shims as necessary at sides and/or bottom.
Hinge Screws
Gasket Adjustment Screw
Figure 5
Figure 4 - Door Installation
6
6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Glass Care
Gasket Replacement
Glass Replacement
The glass used for the Brentwood™ fireplace
is a high temperature ceramic glass (1,400°
F). If the glass breaks, it must be replaced
with an identical ceramic glass. Tempered
glass or ordinary glass will not withstand the
high temperatures of the Brentwood fireplace.
Replacement glass should be purchased from a
Lennox Hearth Products dealer (see “Replacement Parts”, Page 23). DO NOT OPERATE THE
UNIT WITH CRACKED OR BROKEN GLASS.
Glass Cleaning
The Brentwood fireplace is designed to keep
the glass clean under normal operating conditions. If the Brentwood fireplace is operated
continuously with the combustion air controls
closed, the glass will tend to get dirty unless
the fuel, firebox and glass are maintained at
hot temperatures (see “Refueling For Best
Performance”). To clean the glass, there are a
number of specially designed cleaners. Your
authorized Lennox Hearth Products dealer can
recommend a suitable cleaner which is available
in your area. Regular household glass cleaners
will not clean creosote. Do not use abrasives
such as steel pads, steel wool or oven cleaner
as they will scratch the glass.
DO NOT USE CHEMICAL GLASS CLEANERS
ON PAINTED SURFACES AS IT MAY CAUSE
THE PAINT TO PEEL.
CAUTION : DO NOT ALLOW WINDOW CLEANER
TO GET IN CONTACT WITH DOOR OR PAINT
ON FACADE OR DOOR. ONCE CLOSED,
CONTACT OF GLASS CLEANER WITH THE
FIREPLACE FACADE CAN PROVOKE PAINT
PEELING OFF.
Remove the door from the unit (see Page 6)
and lay it on a clean unabrasive surface. To
replace the gasket, first remove all of the old
gasket and gasket cement. Make sure that the
surface is totally clean before applying new
cement (a high temperature silicone caulking
rated at 500° F [260° C] is suitable) or adhesion
problems may result. Apply gasket cement to
the gasket channel and install the new gasket.
This replacement part is available from your
Lennox Hearth Products dealer in the following
dimensions:
Gasket
Length
Dimensions
Part No.
Around
Glass
69
(1753)
5/16” dia.
(8)
SR1823H
On Door
Frame
73
(1854)
5/8 dia.
(15.9)
SR1823G
Table 1
Inches (millimeters)
FIREPLACE INSTALLATION
Locating The Brentwood Fireplace
A.The best location to install your fireplace is
determined by considering the location of
windows, doors, and the traffic flow in the
room where the fireplace is located, allowing space in front of the unit for the hearth
extension and the mantel, and taking into
consideration the location of the hot air ducts
(optional), outside air kit and chimney.
If possible, you should choose a location
where the chimney will pass through the
house without cutting floor or roof joists
(see fireplace dimensions Page 9).
B.Usually, no additional floor support is needed
for the fireplace. The adequacy of the floor
can be checked by first estimating the weight
of the fireplace system. Weights are given
in the appendix. Note the floor construction and consult your local building code to
determine if additional support is needed.
C.The Brentwood fireplace may be installed
directly on the floor or on a raised base (for
proper guidelines, refer to “Hearth Extension
Requirements”) and a minimum of 6’8” (2
m) measured from the base of the appliance
to the ceiling is required.
When selecting the location, the chimney outlet
position and the direction of the wind are important factor affecting the chimney performance.
To allow a maximum draft and to reduce wind
turbulence, the chimney must:
• Penetrate the highest part of the roof.
• Be installed as far as possible of roof offsets,
trees or any other obstructions that may
cause wind turbulence and back drafts in
the chimney.
• The least amount of offsets (elbows) possible.
Location Recommended
Marginal Location
Wind Direction
Location
Not
Recommended
Location
Not
Recommended
Outside Air Intake
Facing the Wind
Figure 6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Framing, Facing And Mantel
The construction of the framing, facing, and
mantel must be in accordance with the standards and the following illustrations (Figures
7a, 7b and 8):
A.Frame the fireplace using 2” x 3” or heavier
lumber.
B. WARNING: Combustible materials
cannot be used in the space directly
above the fireplace, except for the
studs above the facade that support
the facing and mantel. This area must
remain empty for a height of 6’8”
(2,032 mm) measured from the base
of the appliance.
C.Frame the fireplace with vertical studs at the
sides of the fireplace running from floor to
ceiling (see Figure 8). If combustible facing
is to be used, position the studs back, from
the front edge of the fireplace (a space that
is the thickness of the facing material, so
that the facing can be installed flush with the
fireplace facing). Frame headers between
the vertical studs only as follows:
- Place 2” x 3” or 2” x 4” headers,
only along the upper part of the front,
side and back faces (some codes
may require a 2” x 6 ” on an outside
bearing wall). Do not put wood or any
combustible material within the area
above the fireplace except on the front
facing.
- Place headers only as required to support
the facing and mantel.
WARNING: THE HEARTH EXTENSION IS TO BE INSTALLED ONLY
AS ILLUSTRATED.
Fireplace
The crack between the fireplace
and the hearth extension must be
sealed with a non-combustible
material such as sand-cement
grout.
Safety Metal Strip
Hearth Extension
Non-Combustible
Finish Material
1/2”
13mm
Floor
Elevated Fireplaces
Fireplace
u.Elevated fireplace installations
require a special “Z” Metal
Safety Strips (field provided),
in place of the safety metal strip
shown above. The safety strip
should extend the full width of
the fireplace. When more than
one safety strip is used they must
overlap by a minimum of 1”.
Platform
2”
u
Figure 7A - Hearth Extension Requirements
D.WARNING: The fireplace must not be
in contact with any insulation or loose
filling material. Cover the insulation with Drywall panels around the
fireplace.
up to
12”
(305mm)
Hearth Extension Requirements
The Brentwood fireplace may be installed
directly on a combustible floor. The supplied
safety metal strip must be positioned as follows: One half under the front of the fireplace
and the other half must extend on the floor
over which the hearth extension will be built
(see Figure 7a).
Mantel
Area where wood
Mantel can be
installed
* The safety metal strip must cover the entire
width of the fireplace
The combustible floor in front of the fireplace
must be covered with a non-combustible
material (tile, marble, stone, etc). See Figures
7a and 7b.
Cold climate INSTALLATIONS
Climates where temperatures will fall below
32° F (0° C).
The heating performance of the appliance will
vary depending upon the level of insulation,
house design, how the appliance is operated,
etc.
8
If this fireplace is being installed in a cold
climate, it is especially important to seal all
cracks around the fireplace and wherever cold
air could enter the room with noncombustible
material.
45”
(1143mm)
Min.
Hearth
Extension
4”
(102mm)
18”
(457mm)
45 Deg.
36”
(914mm)
17” Min.
(432mm)
Non-Combustible Material
Figure 7b - Hearth Extension Requirements
Also, the outside air inlet duct should be wrapped with noncombustible insulation to minimize
the formation of condensation. Do not place insulation materials directly against the chimney
sections. We recommend that you use the insulated wall radiation shield since it will maintain
the home’s thermal barrier. AC chimney is NOT recommended in very cold climates (in areas with
temperatures below 0°F (-18°C).
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Back Wall of Chase/Enclosure
Including Finising Materials if any
Combustion
Air Kit
Corner Installation
OUTSIDE CHASE
C
L*
19-3/32”
D
J
F
G
H
K
A
FRAMING DIMENSIONS
Fireplace Opening Width
A
36-3/8”
924 mm
B
37”
940 mm
C
28-3/32”
714 mm
D
13-1/2”
343 mm
E
77”
1956 mm
F
38-1/2”
978 mm
G
*24-1/2”
603 mm
H
23-1/2”
597 mm
J
54-7/16”
1383 mm
K
8”
203 mm
L
1”
25 mm
20-1/2”
Rough Framing Face (Unfinished Shown)
* Zero Clearance From Back Spacer to Wall
Combustible materials can NOT be used in
the space directly above the fireplace. Do
not fill the space above the fireplace with any
material (Except the wood framing)
2” x 3’
Min.
* Total depth is 25
inches including
the back spacer
minus 1/2 inch for
drywall to be flush
with the facing.
Header
B
7’
Min.
Combustible materials
can NOT be used in the
space directly above
the fireplace. Do not
fill the space above
the fireplace with any
material (Except the
wood framing)
A
Fireplace Framing
2” x 3”
Min.
Notes
Diagrams, illustrations and photographs
are not to scale – consult installation
instructions. Product designs, materials,
dimensions, specifications, colors and
prices are subject to change or discontinuance without notice.
Plywood 1/2”
28-3/32"
7’
Min.
E
G
10-1/4"
B
1"
9-1/4"
12-1/2"
22-19/32"
24"
Rough Framing Face
(dimension includes finish
material inside framing, if any)
All framing dimensions calculated for
1/2" dry wall at the fireplace face. If
sheathing the chase or finishing with
other thickness materials, calculations
will need to be made.
* The fireplace must not be in contact with
any insulation or loose filling material.
Cover the insulation with Drywall panels
around the fireplace.
1-1/2"
14-5/32"
9-7/8"
36-13/16"
36-1/16"
12-1/4"
26-11/16"
26-11/16"
7-11/16"
14-3/8"
2-13/16"
3-9/16"
24"
Figure 8 - Fireplace and Framing Dimensions
22-1/2"
35-15/16"
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Insulate Joists
Same As Ceiling
Insulated Chase Construction
Storm Collar
Roof Support
Flashing
Attic Radiation
Shield
Draft Stops
Floor
Ceiling
Wall
NOTE:Itisrecommendedthatthechasewalls
and floor be insulated in the same manner,
using the same insulation, as the rest of the
building, below the attic.
Firestop
CTDT
Termination
• Must have the same firestopping
Note: Nonresistance as adjacent
wall.
Combustible
• Must have the Chase
same insulation as
adjacent ceiling.Flashing
Must Be
Usedregarding
To
• Follow local rules
framing
Cover
construction. Chase
Firestop
Opening
Figure 9
Four nailing flanges are provided to secure the
fireplace to the floor (see figure below). Bend
the nailing flanges down so that each flange is
flush with the floor, then using nails or screws,
secure the fireplace to the floor (2 places each
side). The heads of the screws or nails must
be large enough to completely cover the holes
in the nailing flanges.
8’8'
(2.4
m)
Level
Level
Non-Combustible Facing
1/2” Drywall
Mantel
The mantel must be installed at least 45”
(1143 mm) above the base of the fireplace
(Figure 10).
2” X 3” Min.
Spacer
1/2” Drywall
2” X 3” Min.
Fireplace Side
Spacer
12”
(305mm)
MAX
Unbend to floor
and nail/screw
45”
(1143mm)
Min.
Door
Figure 11
Facing
10
1. Combustible material must be installed flush
with the fireplace. It may not project in front
of and on the fireplace (i.e. the steel facade
of the fireplace) (Figure 10).
Outside
Base
Insulation
(Thermal Barrier)
2. Non-combustible materials such as brick,
stone or ceramic tile may project in front of
and onto the fireplace facing (Figure 11).
Mantel
Nailing Flange
(2 places each side)
Solid
Continuous
Surface
Drywall or Any Rigid
Material
2x4
1/2” Plywood
Nailing Flanges
SEE NOTE
FIREPLACE
7’
(2.1 m)
Min.
6’ 8”
(2 m)
Min.
Figure 10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
HOT AIR DUCTING INSTALLATION
The Brentwood™ fireplace is approved for use
with a Gravity Kit.
Gravity Kit
The gravity kit is designed for double hot air outlets and includes: (See Figures 12 and 13)
- 2 telescopic lengths 8” I.D.
- 2 90º elbows 8” I.D.
- 2 hot air outlet kits (grill and frames)
- 2 adaptors
WARNING: The outlet grills
should not be installed facing upward through a floor.
Danger of burns can result
if grills in floor are stepped
on.
See Gravity Kit Accessories on Page 20.
Outlet Grill
The only blower that can be used with the gravity
kit is the UZY5.
The gravity kit allows you to block the upper
louver of the fireplace. To do so, follow the
steps below:
a)Remove the upper louver from the fireplace.
b)Install the black panel (BWCF) making sure
that the insulation strip is installed inside.
c)The fireplace facade can be covered with
non-combustible material (Figure 14).
Outlet Grill
10’
(3.1m)
Max.
13” x 13”
(330mm x 330mm)
10’ (3.1m)
Max.
Maintain at least 6-1/2”
(160 mm) clearance from
the outlet grill framing to
a combustible ceiling,
side wall or mantel.
Frame
Figure 13
Grill
Rain Cap
WARNING: Both pipes of
the double hot air outlet
must be installed. Any other installation may cause
fire and void warranty.
Collar
Flashing
Roof Support
Attic Radiation
Shield
Radiation Shield (Firestop)
6-1/2” Min.
(to ceiling)
Figure 12
68” Min.
(1727mm)
For safe installation, the gravity kit must meet
the following requirements:
Minimum height*
Maximum length
68” (1,727 mm)
See Figures 13 and 14
45” Min.
(1143mm)
* The height of the louver must be measured
from the base of the Brentwood fireplace to the
middle point of the louver.
To extend the double outlet system forward of
the Brentwood fireplace (not flush), it will be
necessary to purchase two adjustable lengths
(7B26ZL2A). When installing the double outlet system, the
hot air outlets can be installed in the same room
as the fireplace, or one or both of the outlets
can be installed in adjacent or upper rooms.
Installing the ducts at different elevations will
tend to exhaust more heat out of the higher
outlet (Figure 13).
Non-Combustible
Facing
Figure 14
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
11
The duct system must be installed respecting
the following:
1. Remove the plates closing up the 8” dia. holes
on top of the fireplace. Then, cut the insulation in order to obtain two 8” dia. openings.
Fix the adaptors on the fireplace openings
by turning clockwise (Figure 12).
2. Maintain at least a 2” (50 mm) clearance
between the ducts and any combustible
material; the required hole size is 13” x 13”
(330 mm x 330 mm).
Exception #1: For the grills, the framing can be 10-3/4” x 10-3/4” (275 mm
x 275 mm) to provide the clearance as
required by the integral spacers on the
double outlet duct system.
3. The maximum number of elbows in a run
of duct is two.
4. Maintain at least 6-1/2” (160 mm) clearance
from the outlet grill framing to a combustible
ceiling, side wall or mantel.
5. When traversing a combustible wall or floor,
a firestop must be installed at the wall or
floor penetration. The hole size must be
13” X 13” (330 mm x 330 mm).
6. Do not connect the hot air ducts to a central
heating system. Malfunction of the heating
system’s blower will cause the fireplace to
overheat. A furnace duct is only single wall
and not double wall as is required for the
Brentwood™ fireplace hot air exhaust.
7. Use only Lennox Hearth Products grills and
components as described in this manual.
Other grills or registers, for example, may be
too restrictive and may overheat the fireplace
or ceiling.
OUTSIDE AIR KIT
During operation, the fireplace requires fresh air for combustion and draws air out of the house.
It may starve other fuel burning appliances such as gas or oil furnaces. As well, exhaust blowers may compete for air, causing negative pressure in the house, resulting in smoke entering the
house from the fireplace. This situation is aggravated in modern airtight houses. To overcome
this problem, we strongly recommend that you install an outside air assembly. Check with local
authorities having jurisdiction in your area, it may be mandatory.
Note: Should you decide not to install the outside air assembly, proceed as follows:
- Remove the bottom grill. The air box is located on front left and is on a slant.
- Unscrew the four screws holding the inside air box covering plate and remove it.
Outside Air Installation
The outside air assembly may be installed according to the following requirements:
A)Duct length should be kept to a minimum. The maximum length of duct is twenty (20) feet (6.1
m) for a 4 in. dia. pipe (See note below).
B)The air intake register must not be installed more than ten (10) feet (3050 mm) above the base
of the fireplace.
C)The fresh air must come from outside the house. The air intake must not draw air from the
attic, from the basement or garage.
D)The air intake should be installed where it is not likely to be blocked by snow or exposed to
extreme wind and away from automobile exhaust fumes, gas meters and other vents.
E)The duct and register may be installed above or below floor level.
The following components are required:
- Outside air kit (UZI) (includes 40 inch flex that goes up to ten (10) feet long)
- 4” Adaptor for fireplace connection (supplied with the unit)
Make a 4-1/4” (110 mm) hole in the outside wall of the house at the chosen location. From outside,
place the outside air register in the hole (open side down) and fasten the register to the wall, with
screws as shown (see Figure 15). Slip the pipe into the insulated sleeve. Place the insulated pipe
over the register tube and over the fireplace’s outside air connector (see Figure 16). At each end,
carefully pull back the insulation and plastic cover exposing the flexible pipe. Using the aluminium
tape provided, wrap the tape around the joint between the flexible pipe and the air inlets. Carefully
push the insulation and plastic cover back over the pipe. Using aluminium tape, fasten the plastic
cover in place.
Note: We recommend not to exceed 20 feet of 4” flexible pipe. If you require a longer length we
recommend that you use a 5” diameter flexible pipe for the complete run up to 30 feet and a 6”
diameter pipe for a run of up to 40 feet.
8. Do not use insulated flexible ducts as they
will overheat.
9. Do not use tees or any other components
than the ones specifically listed here.
10.Never allow the ducting to pitch down as
hot air will be trapped creating a fire hazard.
Never route the ducting downwards.
OUTSIDE CONNECTION
Outside
Intake
Plastic Cover
11.The hot air outlet grills must be installed with
the louvers pointing downwards in order to
prevent overheating adjacent ceilings.
12.Always install the two outlet grills when using
the double hot air outlet kit and blocking the
upper louver of the fireplace.
Screw
Insulation
Opening
Facing
Down
Wall
Figure 15
12
Aluminum Tape
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Flexible Pipe
Aluminum Tape
OUTSIDE AIR CONNECTION TO THE FIREPLACE
Fireplace
Connection
Aluminum Tape
Plastic
Cover
Fireplace
6. The chimney must extend at least three (3) feet (915 mm) above its
point of contact with the roof and at least two (2) feet (610 mm) higher
than any wall, roof or building within ten (10) feet (3m) of it (Figure
17).
7. If the chimney extends higher than five (5) feet (1,500 mm) above
its point of contact with the roof, it must be secured using a roof
brace.
8. A rain cap must be installed on top of the chimney. Failure to install
a rain cap may cause corrosion problems.
Insulation
Flexible Pipe
Aluminum Tape
9. Cut and frame square holes in all floors, ceilings, and roof that the
chimney will go through to provide a 2” (50 mm) clearance between
the chimney and any combustible materials. Do not fill this 2” space
with insulation or any other combustible material.
Figure 16
THE CHIMNEY system
Chimney Installation Notes
1. Always install an interior chimney as it will provide better performance.
In areas with continuous temperatures below - 18° C (0° F), the use of
an exterior chimney increases the likelihood of operating problems such
as low draft, high rate of creosoting, and poor start-up characteristics.
Exterior chimneys are also prone to down drafting and flow reversal.
Installations, which are located on lower floors in the house, such as
in a basement, in combination with outside chimney, are especially
prone to flow reversal. If interior installation is impossible, install an
AC chimney enclosed in an insulated chase.
10.Portions of the chimney which may extend through accessible spaces
must be enclosed to avoid contact with combustible materials or
damage to the chimney.
11.When offsets are used, the pipe may not penetrate a ceiling or floor
unless it is running vertical (no 30° offsets).
two (2) feet Min.
2. The fireplace model Brentwood SP may be installed only with Security
Chimneys International Ltd 6” diameter chimney systems.
ten (10) feet
three (3) feet Min.
3. A chimney venting a fireplace shall not vent any other appliance.
4. The minimum chimney height is 12 feet (3.7 m). In altitude, add 18”
(450 mm) to the chimney for every 2,000 feet (600 m) above sea
level.
5. All chimney installations must include at least one support. The
maximum length of chimney that can be supported by the fireplace
is 26 feet (8 m).
Figure 17
Note: 2" clearance to combustibles around chimney components required.
Note: Blown or fill type insulation materials must not be in contact with the
fireplace or in the enclosure frame as described in ‘’Enclosure’’ section.
Note: Local codes may not require firestopping at the ceiling levels for
outside chase installations. However, it is recommended for safety and
the reduction of heat loss.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
13
CHIMNEY INSTALLATION INSTRUCTIONS
1. Cut and frame the holes in the ceiling, floor
and roof where the chimney will pass (see
Figure 18). Use a plumb-bob to line up the
center of the holes. The sizes are indicated
in Table 2 for the floor and ceiling holes
and Table 3 (Page 12) for the roof holes.
CHIMNEY MODEL
SQUARE HOLE
SIZE OPENING
ASHT / HT6103+
12-3/8” (314 mm)
S-2100+ / HT6000+
14-1/8” (359 mm)
AC
15 in (380 mm)
Note: See Table 3 for Sloped Roof Framing
Table 2 - Flat Roof Framing
Attic Radiation Shield
ASHT / S2100
HT6103+ / HT6000+
Solid Packed Pipe
Attic Radiation
Shield
Flashing
Roof
Firestop
Figure 19a
AC
Air Cooled Pipe
Mobile / Manufactured Home with Flat Roof
ASHT / S2100
HT6103+ / HT6000+
Figure 19b
Attic Radiation
Shield
Attic Radiation
Shield
Flashing
Radiation Shield
Figure 18 - Roof Framing
14
2. From below, install a firestop in each ceiling/
floor separation through which the chimney
will pass. At the attic level, install an attic
radiation shield from above (Figures 19a
through 19d).
3. For ASHT / HT6103+ AND S2100+ / HT6000+
chimneys place the first chimney length on
the fireplace. To lock it in place, turn 1/4
of a turn clockwise. With the AC chimney,
you must use a starter section (AC6SB or
AC6SB30) before installing the first chimney length (Figure 20). Continue installing
chimney lengths making sure to lock each
length in place.
4. Every time the chimney passes through
a ceiling or a wall, install the appropriate
firestop. When you reach the desired height,
install the roof support (Refer to instructions
included with the support).
5. Then, put the roof flashing in place and seal
the joint between the roof and the flashing
with roofing pitch (see Figures 21 and 22).
For sloping roofs, place the flashing under
the upper shingles and on top of the lower
shingles. Nail the flashing to the roof, using
roofing nails.
6. Place the spacers and the storm collar over
the flashing, and tighten it with the bolt
supplied. Finally, seal the joint between the
storm collar and the chimney, using silicone
caulking.
7. Install the chimney cap. Once the chimney
cap is in place, the roof flashing can be
washed with a solvent or vinegar and then
painted with rust-proof paint.
Figure 19c
Mobile / Manufactured Home with Flat Roof
AC Chimney
Figure 19d
Rain Cap
AC CHIMNEY INSTALLATION
(AIR COOLED GALVANIZED CHIMNEY)
Collar
Flashing
Attic Radiation
Shield
Firestop
Chimney Outside
Air Intake
(required when
using AC chimney)
Outside Combustion
Air Kit
Figure 20
Starter Section
Figure 31
After reaching the location requiring the
elbow, proceed as follows:
AC
Air Cooled Chimney
Chimney
ASHT / HT6103+ / S-2100+ / HT6000+ Chimneys
Collar
Spacer (built
into flashing
Flashing
Figure 22
Figure 21
Roof Down Slope Hole Size
SLOPE
ASHT / HT6103+
S-2100+ / HT6000+
AC
Roof Pitch
6”
6”
6”
0*
12-3/8” (314 mm)
14-1/8” (359 mm)
15” (380 mm)
2/12
12-9/16” (319 mm)
14-3/8” (365 mm)
15 3/8” (390 mm)
4/12
13” (330 mm)
14-7/8” (378 mm)
16 1/8” (410 mm)
6/12
13-7/8” (352 mm)
15-3/4” (400 mm)
16 7/8” (430 mm)
8/12
14-7/8” (378 mm)
17” (432 mm)
18 1/4” (465 mm)
10/12
16-1/8” (410 mm)
18-3/8” (467 mm)
19 5/8” (500 mm)
12/12
17-1/2” (445 mm)
20” (508 mm)
21 3/8” (545 mm)
* Cross Slope Hole Size
Put the chimney cap into place.
Wash the roof flashing with a solvent or vinegar, then paint it with rust-proof paint.
Table 3
OFFSET CHIMNEY INSTALLATION
After reaching the location requiring the elbow, proceed as follows. The minimum chimney height
when using elbows is:
Minimum Chimney Height Using Elbows
Fireplace Model
Brentwood SP
Chimney Model
ASHT / S2100+ / HT6103+ / HT6000+ / AC
Vertical installation
12 feet (3.66 m)
Two (2) elbows
15 feet (4.57 m)
Four (4) elbows
17 feet (5.18 m)
Table 4
Notes:
• Must return to vertical before penetrating ceiling or floor.
• A maximum of 2 offsets are allowed.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1. Install the first elbow; turn it in the required
direction. Fasten it to the chimney with
the three (3) 1/2” (12 mm) metal screws
provided with the elbow.
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together: it is recommended to use
three (3) 1/2” (12 mm) screws. If the offset
length is made of two (2) chimney lengths or
more, use an offset or roof support halfway
up the offset. If penetrating a wall, install
a wall radiation shield (see Figures 24 and
26).
3. Use another elbow to turn the chimney
vertically. Secure the elbow, using three
(3) 1/2” (12 mm) screws (provided with the
elbow).
4. Use a plumb-bob to line up the center of
the hole. Cut a hole for the chimney in the
ceiling/floor. Frame this hole as described
previously (refer to section Chimney Installation Instructions).
5. From below, install a firestop (See Figure
19a).
6. A support (ST or SO+) must be used on the
first 15’ section (5 m).
7. Continue with the regular installation.
AC Chimney
1. Install the first elbow. Turn it in the required
direction. To lock it in place, turn 1/8 of a
turn. Fasten the straps attached to the elbow
to the surrounding frame, using nails or
drywall screws (Figure 25).
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together. If penetrating a wall, use
a wall radiation shield.
3. Use another elbow to turn the chimney
vertically. Lock it to the chimney. Fasten
the straps attached to the elbow to the
surrounding framing using nails or drywall
screws.
4. Use a plumb-bob to line up the center of the
hole. Cut a hole for the chimney in the ceiling.
Frame this hole as described previously.
5. From below, install a firestop (see Figure
19c).
6. Continue with the regular installation.
Note: When using AC chimney, an AC6SB
starter section must be used before installing an elbow. When an offset is needed
immediately off the top of the fireplace, an
elbow starter section, AC6SB30 (H3780), is
available.
15
Offset Dimensions
B
Total Height
A
Chimney
6”
Elbow
15º
Secure
Temp
ASHT
30º
Nova
Temp
HT6103+
45º
Chimney
6”
18”
24”
36”
48”
8” & 48”
12” & 48”
18” & 48”
24” & 48”
36” & 48”
48” & 48”
A
3-5/16”
(84mm)
4-5/16”
(110mm)
5-7/8”
(149mm)
7-7/16”
(189mm)
10-1/2”
(267mm)
13-5/8”
(346mm)
15-3/8”
(391mm)
16-7/16”
(418mm)
18”
(457mm)
19-1/2”
(495mm)
22-5/8”
(575mm)
25-3/4”
(654mm)
B
15-11/16”
(398mm)
19-9/16”
(497mm)
25-3/8”
(645mm)
31-3/16”
(792mm)
42-3/4”
(1086mm)
54-3/8”
(1381mm)
60-15/16”
(1548mm)
64-13/16”
(1646mm)
70-9/16”
(1792mm)
76-3/8”
(1940mm)
87”
(2210mm)
99-9/16”
(2529mm)
A
7-7/16”
(189mm)
9-7/16”
(240mm)
12-7/16”
(316mm)
15-7/16”
(392mm)
21-7/16”
(545mm)
27-7/16”
(697mm)
30-13/16”
(783mm)
32-13/16”
(833mm)
35-13/16”
(910mm)
38-13/16”
(986mm)
44-13/16”
(1138mm)
50-13/16”
(1291mm)
B
20”
(508mm)
23-1/2”
(597mm)
28-11/16”
(729mm)
33-7/8”
(860mm)
44-1/4”
(1124mm)
54-11/16”
(1389mm)
60-9/16”
(1538mm)
64“
(1627mm)
69-1/4”
(1759mm)
74-7/16”
(1891mm)
84-13/16”
(2154mm)
95-1/4”
(2419mm)
A
10-5/16”
(262mm)
13-3/16”
(335mm)
17-3/8”
(441mm)
21-5/8”
(549mm)
30-1/8”
(765mm)
38-5/8”
(981mm)
43-7/16”
(113mm)
46-1/4”
(1175mm)
50-1/2”
(1283mm)
54-3/4”
(1391mm)
63-1/4”
(1607mm)
71-11/16”
(1818mm)
B
17-13/16”
(452mm)
20-5/8”
(524mm)
24-7/8”
(632mm)
29-1/8”
(740mm)
37-5/8”
(956mm)
46-1/8”
(1172mm)
50-15/16”
(1294mm)
53-3/4”
(1365mm)
58”
(1473mm)
62-1/4”
(1581mm)
70-3/4”
(1797mm)
79-3/16”
(2011mm)
15º
30º
Elbow
15”
AC
6”
30”
Two Lengths Between Elbows
12”
Offset &
Height
Nova Temp
HT6000
One Length Between Elbows
8”
Elbow
Secure
Temp
S2100+
Chimney
6”
Offset &
Height
Horizontal Offset
One Length Between Elbows
Two Lengths Between Elbows
8”
12”
18”
24”
36”
48”
8” & 48”
12” & 48”
18” & 48”
24” & 48”
36” & 48”
48” & 48”
A
3-5/16”
(84mm)
4-5/16”
(110mm)
5-7/8”
(149mm)
7-7/16”
(189mm)
10-1/2”
(267mm)
13-5/8”
(346mm)
15-1/2”
(394mm)
16-1/2”
(419mm)
18-1/16”
(459mm)
19-5/8”
(498mm)
22-3/4”
(578mm)
25-13/16”
(656mm)
B
16”
(406mm)
19-7/8”
(505mm)
25-11/16”
(652mm)
31-1/2”
(800mm)
43-1/16”
(1094mm)
54-5/8”
(1387mm)
61-7/16”
(1561mm)
65-1/4”
(1657mm)
71-1/16”
(1805mm)
76-7/8”
(1953mm)
88-1/2”
(2248mm)
100-1/16”
(2542mm)
A
7-3/8”
(187mm)
9-3/8”
(238mm)
12-3/8”
(314mm)
15-3/8”
(391mm)
21-3/8”
(543mm)
27-3/8”
(695mm)
30-7/8”
(784mm)
32-7/8”
(835mm)
35-7/8”
(911mm)
38-7/8”
(987mm)
44-7/8”
(1140mm)
50-7/8”
(1292mm)
B
20-11/16”
(525mm)
24-3/16”
(614mm)
29-3/8”
(746mm)
34-9/16”
(878mm)
44-15/16”
(1141mm)
55-5/16”
(1405mm)
61-3/8”
(1559mm)
64-7/8”
(1648mm)
70-1/16”
(1780mm)
75-1/4”
(1911mm)
35-5/8”
(2175mm)
96”
(2438mm)
---
12”
18”
---
36”
48”
---
12” & 48”
18” & 48”
---
36” & 48”
48” & 48”
A
-------
4-13/16”
(122 mm)
6-1/8”
(156 mm)
-------
11”
(280 mm)
14-1/8”
(359 mm)
-------
16-7/8”
(429 mm)
18-7/16
(468 mm)
-------
23”
(584 mm)
26-3/16”
(665 mm)
B
-------
27-11/16”
(703 mm)
33-1/2”
(851 mm)
-------
50-7/8”
(1292 mm)
62-1/2”
(1588 mm)
-------
72-5/8”
(1845 mm)
78-7/16”
(1992 mm)
-------
95-3/4”
(2432 mm)
107-3/8”
(2727 mm)
A
-------
9-3/8”
(238 mm)
12-3/8”
(314 mm)
-------
21-3/8”
(543)
27-3/8”
(695 mm)
-------
32-5/8”
(829 mm)
35-5/8”
(905 mm)
-------
44-5/8”
(1134 mm)
50-5/8”
(1286 mm)
B
-------
25-3/4”
(654 mm)
31”
(787 mm)
-------
46-1/2”
(1181 mm)
57”
(1448 mm)
-------
66”
(1676 mm)
71-1/4”
(1810 mm)
-------
86-7/8”
(2207 mm)
97-1/4”
(2740 mm)
Offset &
Height
One Length Between Elbows
Two Lengths Between Elbows
NOTE: With the AC chimney, a starting length of 6” high must be used on top of the fireplace before installing an elbow.
Figure 23
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ANGLED WALL RADIATION SHIELD
(RSM+ and RSMI30)
When traversing a combustible wall with the chimney at a 30º or 45º
angle, an angled firestop or wall radiation shield must be installed. Only
one is required.
Support
ACRS
Straps
Straps
Note: 45º angle for Canada only (RSMI45)
In cold climate locations (climates where temperatures will fall below 32°
F / 0° C), we recommend that you use the insulated wall radiation shield
since it will maintain the home’s thermal barrier.
RSM+ and RSMI30
(RSMI45 - Canada Only)
Chimney AC
Starter Section
Chimney Model
Angle
Hole Size
ASHT / HT6103+ (6”
dia). Canada only
30º
283 mm x 781 mm (11-1/8” x 30-3/4”)
45º
283 mm x 518 mm (11-1/8” x 20-3/8”)
S-2100+ / HT6000+ /
AC (6” dia).
30º
327 mm x 881 mm (12-7/8” x 34-11/16”)
30º
380 mm x 972 mm (15” x 38-1/4”)
Table 5
Insulated Wall
Note: This illustration is not to scale. It represents how the chimney
must be supported. A 30 degree offset only is allowed in the USA
and a 45 degree maximum offset is allowed in Canada.
Figure 25 - Offset Chimney Installation
Drywall
Rain Cap
Collar
Roof Flashing
Figure 24
Insulated Wall
Radiation Shield
Offset Support
Framing
2” x 3”
Insulated Wall
Radiation Shield
Note: In cold areas it is recommended to protect the
chimney in a insulated chase.
Figure 26
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
17
CHIMNEY SUPPORT INSTALLATION
Universal Roof Support
18” (460 mm)
This support has three possible uses:
1. For ASHT / HT6103+ and S-2100+ / HT6000+, it must be used on a
roof to support the chimney.
2. It may be used on a floor, ceiling or roof above an offset to support
the chimney above the offset.
3. It may be used on a floor, ceiling or roof as a supplementary support.
16” (410 mm)
18” (460 mm)
16” (410 mm)
18” (460 mm)
Table 6 gives maximum height of supported chimney.
NOTE: For the AC chimney, a support section must be used every 40 feet
(12 m) instead of the universal roof support (ST).
For roof support installation, refer to the instructions provided with the
support.
Figure 27
Universal Offset Support
CHIMNEY ADAPTOR (S-2100+ / HT6000+) CANADA ONLY
This support is used to support the chimney above an offset. When
the chimney offset is used to traverse a wall this support may be used
on the wall to support the chimney. The maximum heights are given in
Table 6. For offset support installation, refer to the instructions provided
with the support.
The fireplace is normally supplied with a chimney adaptor suitable for the
ASHT / HT6103+ chimney. If you want to install a S-2100+ / HT6000+
chimney, an adaptor is available (6UCA) (Figure 28). A separate starter
section will also be required if AC chimney is installed.
CHIMNEY MODEL
MAXIMUM HEIGHT OF
SUPPORTED CHIMNEY
Offset Support
Roof Support
ASHT / HT6103+ (6” dia).
28 feet (8.54 m)
29 feet (8.84 m)
S-2100+ / HT6000+ (6” dia).
18 feet (5.49 m)
20 feet (6.1 m)
AC (6” dia).
40 feet (12.19 m)
50 feet (15.20 m)
Chimney Adaptor Canada only
Table 6
CHIMNEY CHASE AND MULTIPLE TERMINATIONS
For the purpose of this manual, a chimney chase is considered a part of
the chimney system rather than part of a building. The termination must
be placed a minimum of 18” (460 mm) above the chase.
For installations where more than one chimney is located in the same
chase or within the same area, we suggest that their terminations be
separated by at least 16” (410 mm) horizontally, and 18” (460 mm) vertically. This separation is to prevent smoke migrating from one chimney
to another (see Figure 27).
18
Figure 28
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION
Follow these steps:
WARNING: Before starting the installation, the masonry chimney
must be inspected by a qualified chimney sweep.
1-Position the fireplace in its location. Temporarily install the ASHT
elbow on the top of the fireplace and, using a level, mark with an oval
the location where the flue liner will enter the masonry chimney.
2-In the middle of the oval, drill a hole in the masonry chimney at
30º.
3-Increase the size of the hole until a or 30º TUBINOX liner elbow can
be easily slipped through.
4-Slide the liner down from the top of the masonry chimney until you
reach the hole level.
5-Slip through the hole a 30º liner elbow and connect it to the liner.
6-Add a small liner section to the liner elbow which will allow the liner to
extend at least 12” (measured at the top of the liner) from the masonry
chimney.
7-Seal the opening around the liner with high temperature refractory
cement.
8-The next steps must be done in the following order:
The following requirements must be respected:
1. The chimney must be absolutely clear of any soot residue or creosote.
Check for cracks, loose or missing bricks that could inhibit correct
installation of the liner.
2. The clearance to combustible must be a minimum of 1” between the
outside of the masonry and any wood framing or loose insulation.
3. The chimney must be built in accordance with the current building
code.
4. No other appliance can be connected to the same chimney.
5. The clearances to combustible for the BISUMA30 connectors are 2”
on the side and bottom and 16” at the top.
6. The connector parts are not necessary if the connection between
the insulated length and the stainless steel liner is done within the
masonry chimney.
Installation:
The chimney must be relined with a stainless steel liner model TUBINOX
or Projet SS of the same diameter as the outlet of the fireplace.
For connection at a 30º angle, a special connector (BISUMA30) must be
used to connect the liner to the insulated chimney.
* IMPORTANT NOTE - The use of a 45º connector (BISUMA) is approved
for use in Canada ONLY. Installations in the USA must use the 30º
connector (BISUMA30).
See typical installation illustrated below.
A.Select the ASHT length that will fit between the elbow and the liner
so that it will slide at least 2” over the liner section (You may need to
cut the liner for a better fit).
B.Take that section and the BISUMA30 cover and slide it over the liner. Make sure you have enough opening to be able to install the ASHT
elbow without difficulty.
C.Install the 30º elbow on the fireplace.
D.Slide the length section back down on the elbow and twist lock the
two together.
E. Pull the cover down over the length and install the insulation pad over
the liner; be careful to cover the liner completely.
F. Slide back the cover over the insulation and fix it in place using the 3
metal screws supplied.
1” Clearance
High-Temp.
Cement
Insulation Pad
& Cover
* Insulated 30 Deg.
3 Screws
Elbow ASHT or
HT6103+
Firestop
TUBINOX or Projet SS
Stainless Steel Liner
TUBINOX or Projet SS
Liner Must Slide at
Least 2” Inside Length
Insulated
Length
6’ 8”
Masonry Chimney,
New or Existing
FIREPLACE
Figure 29
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
19
Optional installation accessories
Installation Accessories
Description
Fireplace Kits
Blower (heat activated on/off pre-wired), UZY5
(Required - Order Separately)
Black Cast Iron Door for Brentwood ™, BWBK
H0516
Gold Plated Cast Iron Door for Brentwood, BWG
H0517
Brushed Nickel Cast Door for Brentwood, BWBN
H4849
Outside Air Kit (Required - Included With Fireplace)
Outside Air Coupler to connect outside air UZI to fireplace,
UZIAD
UZIAD
Outside Air Ducting - includes 4” insulated flex x 10’ long,
UZI
UZI
Gravity Kits
Gravity Kit - Complete double ducting system w/adaptor
including: 2 elbows 90º, 2 telescopic lengths, 2 grill supports
and 2 black grills, 7B30ZK-1
20
Blower motor speed control (wall mount), VRUW
7B30ZK-1
Black grill with support, Part# 7B30ZO
7B30ZO
Brass grill (for 7B30ZK), 7B30ZGB
7B30ZGB
Elbow 90º, 8” dia., 7B26ZE90
7B26ZE90
Elbow 45º, 8” dia., 7B26ZE45
7B26ZE45
Telescopic length, 8” dia., 7B26ZLA
7B26ZLA
Adjustable length 8” dia (2” - 5”), 7B26ZL2A
7B26ZL2A
Cat./Part No.
UZY5
VRUW
Rigid firescreen
BUCEBWZN
Masonry Chimney Adaptor, 30º, BISUMA30
(for use with TUBINOX liner)
BISUMA30
Central Forced Air Kit Accessories u
Central Forced Air Kit, Central forced air kit including: blower
(BISZY), flex adaptor (BISAF), 2 clamps, variable speed
control (VRUW), thermo-disk (VTU), fan to flexible pipe
adapter (BISAVF), back draft damper (BISBD), aluminium
tape, BISFWK-1
Fireplace to Flex adaptor and 2 clamps, BISAF
Gravity Kit Accessories
Wall Radiation shield, 7B26ZR
Description
Cat./Part No.
BISFWK-1
BISAF
Flexible pipe 5” I.D. x 15 ft. Long, 5FLEX15
5FLEX15
Flexible pipe 5” I.D. x 30 ft. Long, 5FLEX25
5FLEX25
Blower 250 CFM for central forced air kit, BISZY
BISZY
Blower variable speed control with decorative wall plate for
(BISZY), VRUW
VRUW
Thermo-disk, on/off blower control (for BISZY), VTU
Blower to flexible pipe adaptor, BISAVF
VTU
BISAVF
Heating and cooling thermostat, 24V, HCTW
HCTW
Backdraft damper, BISBD
BISBD
7B26ZR
Length five (5) feet, 8KL5
8KL5
Length four (4) feet, 8KL4
8KL4
Length three (3) feet, 8KL3
8KL3
Length two (2) feet, 8KL2
8KL2
Length one (1) feet, 8KL1
8KL1
u
Not tested under EPA certification. If installed, this appliance no
longer qualifies for EPA certification.
* For installation, follow the instructions included with the Central
Forced Air Kit.
Chimney - PARTS AND COMPONENTS LISTs
Fireplace Model Brentwood SP - Approved Venting Components manufactured by Security Chimneys International only.
Secure Temp ASHT 1” High Temp. Insulated Stainless Steel Chimney
6” I.D and 8” O.D., Double-Wall Stainl. Steel, Listed to CAN/UCL-S604 and UL-103HT
Description
Part/Cat. No.
Lengths and Misc. Chimney Components
8” length, 6” Dia., 6L8
6L8
12” length, 6” Dia., 6L12
6L12
18” length, 6” Dia., 6L18
6L18
24” length, 6” Dia., 6L24
6L24
36” length, 6” Dia., 6L36
6L36
48” length, 6” Dia., 6L48
6L48
Adjustable Length 12”, 6” Dia., 6LA
6LA
15º elbow, 6” Dia., 6E15
6E15
30º elbow, 6” Dia., 6E30
6E30
Rain Termination Cap, 6” Dia., 6CC
6CC
Spark Arrester Screen (universal spark arrester band), PE
PE
Wall Band, BM
BM
Supports
Offset Support, SO
SO
Roof Support, ST
ST
Roof Brace, BS2
• 6” diameter chimney - AC (air cooled), Secure Temp™ ASHT (or
Nova Temp™ HT6103+) and Secure Temp S-2100+ (or Nova Temp
HT6000+).
• 6” diameter chimney for relining masonry chimneys - TUBINOX
chimney (or PROJET SS), 6” diameter with adaptor for installation in
a masonry chimney.
Notes:
j
Nova Temp HT6000+ is equivalent to Secure Temp S-2100+
k
Nova Temp HT6103+ is equivalent to Secure Temp ASHT
l
This appliance is equipped with the ASHT Chimney Adaptor.
When other
chimney is used, a chimney adaptor for that chimney will be required.
mChimney Adaptor (S-2100+ / HT6000+) for CANADA ONLY -
If you want to
install a S-2100+ / HT6000+ chimney, an adaptor is available (6UCA).
n
AC Chimney is NOT recommended at elevations above 4,000 feet or in cold
climates (climates where temperatures will fall below 32° F / 0° C). When
using AC chimney, an AC6SB starter section must be used before installing
an elbow. When an offset is needed immediately off the top of the fireplace,
an elbow starter section, AC6SB30 (H3780), is available.
BS2
Firestops
Firestop, 6BF
6BF
Radiation Shield, 6RS
6RS
Insulated Attic Radiation Shield, 6RSA
Insulated Wall Radiation Shield, 6RSM
6RSA2
6RSM
Insulated Wall Radiation Shield, 30º, 6RSMI30
6RSMI30
Uninsulated Wall Radiation Shield, 30º, 6RSM30
6RSM30
Attic Radiation Shield
H0487
Roof Flashings
Flat Roof Flashing, 6FR
6FR
1/12 - 7/12 (5º - 30º), 6FAR
6FAR
8/12 - 12/12 (30º - 45º), 6FBR
6FBR
Storm Collar, 6FC
6FC
21
Chimney - PARTS AND COMPONENTS LISTs
(AC) Air-Cooled Chimney System*
TUBINOX LL Chimney Lining System
6” I.D. and 11” O.D. Air Cooled, Stainl. Steel inner and zinc coated steel exterior
AC Starter Adaptors
* AC Chimney is NOT recommended at elevations above 4,000 feet or in cold climates
(climates where temperatures will fall below 32° F / 0° C).
Cat./Part No.
Starter Section (adaptor), 6”, AC, AC6SB
H3779
Starter 30º Elbow, 6” AC, AC6SB30
H3780
The following outside air kit is required if installing an AC chimney system
Chimney Outside Air Kit (flex, insulation, outside register
and coupling), ACZI
H1967
Cat./Part No.
6” Length, 6” Dia., 6LL6
6LL6
12” Length, 6” Dia., 6LL12
6LL12
24” Length, 6” Dia., 6LL24
6LL24
36” Length, 6” Dia., 6LL36
6LL36
48” Length, 6” Dia., 6LL48
6LL48
Adjustable Length (7” to 11”), 6” Dia., 6L7A
6L7A
Split Base Tee, 6” Dia., 6LT
6LT
Tee Cap, 6” Dia., 6TCS
6TCS
Twist Lock Tee Cap, 6” Dia., 6LTC
6LTC
H0472
Elbow 30º, 6” Dia., 6LE30
6LE30
18” Length, 6” Dia. x 12” Long, AC6L18
H0473
Elbow 45º, 6” Dia., 6LE45
6LE45
36” Length, 6” Dia. x 36” Long, AC6L36
H0474
Elbow 90º, 6” Dia., 6LE90
6LE90
48” Length, 6” Dia. x 48” Long, AC6L48
H0475
Rain Termination Cap (regular), 6” Dia., 6LCS
6LCS
15º Elbow, 6” Dia., AC6E15
H0476
Rain Termination Cap (deluxe), 6” Dia., 6LCC
6LCC
30º Elbow, 6” Dia., AC6E30
H0477
Spark Arrester Screen (universal spark arrester band), PE
Rain Termination Cap, 6” Dia., AC6CPR
H0478
Lengths and Misc. Chimney Components
12” Length, 6” Dia. x 12” Long, AC6L12
Spark Arrester Screen (universal spark arrester band), PE
Wall Band, XBM
PE
XBM
Supports
Offset Support, SO
Support Section, AC6SL
PE
Supports
Top Support, 6LST
6LST
Support Assembly, 6LSA
6LSA
Interior Support, 6LSB
6LSB
SO
Adaptor Flexible Pipe (male), 6LAAM
H0481
Adaptor Flexible Pipe (female), 6LAAF
Roof Support, ST
ST
Stainless Steel Flex - five (5) feet Long, 6LLFLEX
Roof Brace, BS2
BS2
Adjustable Insulated Wall Radiation Shield 6” - 12”, 6LRSMI
6LAAM
6LAAF
6LLFLEX
6LRSMI
Adaptors to Masonry Chimney
Roof Flashings
Flat Roof Flashing, ACF
H0494
1/12 - 7/12 (5º - 30º), AC Adj. Roof Flashing, FA
H0495
8/12 - 12/12 (30º - 45º), AC Adj. Roof Flashing, FB
H0496
Storm collar, ACFC
H0500
Misc.
22
Listed to ULC-S635M, UL-1777 and ULC-S640M at 2100º F
Description
One of the following adaptors is required
if installing an AC chimney system
Description
Rigid Stainless Steel Liner For Relining A Masonry Chimney, 6” Diameter
Telescopic attic radiation shield, ACRST
H0498
Firestop, ACBF
H0485
Radiation Shield, ACRS
H0486
Attic Radiation Shield, ACRSA
H0487
Insulated Wall Radiation Shield, 30º, ACRSMI30
H0489
Masonry Chimney Adaptor, 45º, BISUMA
(for use with TUBINOX liner) CANADA ONLY
BISUMA
Masonry Chimney Adaptor, 30º, BISUMA30
(for use with TUBINOX liner)
BISUMA30
REPLACEMENT PARTS LIST
SPECIFICATIONS
Brentwood™ Replacement Parts
Description
Cat./Part No.
Baffle refractory (2 pieces)
PR-ISO2205
Back refractory
PR-SR2203
Cat. No.
Model
H4825
Brentwood SP
Product Reference Information
Right side refractory
PR-SR2204D
Weight
385 lbs
Left side refractory
PR-SR2204G
Height
36”
Bottom refractory
PR-SR2201
Width
36”
Front refractory, right side - ash lip
PR-SR2202D
Depth
24-1/2”
Front refractory, left side - ash lip
PR-SR2202G
Firebox W x H x D - measured in front
22” x 11-3/4” x 12”
Chimney weight ASHT (6” dia)
6.25 lb/ft.
Chimney weight AC (6” dia)
3.25 lb/ft.
Door handle
PR-SR2325
Ceramic glass panel
PR-SR2222-1
Secondary air tube
PR-SR2271
Cast-iron log retainer supports - grate (2)
PR-SR2324
Cast iron log retainer bar (w/Lennox logo)
PR-SR2323
Touch-up paint, aerosol, black metallic SBMB6309
Louvers, upper and lower (1)
Snap disc, blower
Bracket, secondary air tube
Hinge assembly, fireplace and door
70K99
PR-SR2218-1
VTU
PR-SR2214
PR-SR2395UL
Door handle rod and mechanism
PR-SR2118
Door handle and brass cap
PR-SR2325
Door handle brass cap
POIGNE002
Gasket, door, 73” (5/8” dia.)
PR-SR1823G
Gasket, glass, 69” (5/16” dia.)
PR-SR1823H
CLEARANCE TO COMBUSTIBLES
The following clearances meet the minimum requirements for a safe
installation:
Side wall:17” (324 mm) measured from the fireplace side.
Ceiling: 6’ 8” (2,032 mm) measured from the base of the fireplace.
Fireplace enclosure:
Bottom: 0”
Side: 0” to spacer
Back: 0” to spacer
Top: Do not fill the space above the fireplace with any material
(Except the wood framing. See Page 9, Figure 8).
Chimney: 2” (50 mm)
Contact an Authorized Lennox Hearth Products dealer to obtain any of
these parts. Never use substitute materials not approved by Lennox
Hearth Products. Use of non-approved parts can result in poor performance and safety hazards.
Mantel: 45” (1143 mm) measured from the base of the fireplace.
23
Warranty
Your fireplace is covered by a limited warranty. Please read the warranty
to be familiar with its coverage.
Retain this manual. File it with your other documents for future reference.
Product reference information
We recommend that you record the following important information
about your fireplace. Please contact your Lennox Hearth Products dealer
for any questions or concerns. For the number of your nearest Lennox
Hearth Products dealer, please call 1-800-9-LENNOX.
Replacement parts
See Page 23 for a complete replacement parts list. Use only parts supplied from the manufacturer.
Normally, all parts should be ordered through your Lennox Hearth
Products distributor or dealer. Parts will be shipped at prevailing prices
at time of order.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at www.Lennox.com
Your Fireplace's Model Number_________________________________________
Your Fireplace's Serial Number_________________________________________
The Date On Which Your Fireplace Was Installed____________________________
Your Dealer's Name__________________________________________________
Your Dealer's Phone Number___________________________________________
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in Canada © 2006 Lennox Hearth Products
24
P/N 850,039M REV. H 05/2010
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210