05b_067-082_Electrical

05b_067-082_Electrical
BATTERY ACCESSORIES
Meters/Testers
In Section D:
Wiring
Fuses
12V Accessories
D
ELECTRICAL
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
Designed for the RV Owner!
SURE POWER BATTERY ISOLATORS &
SEPARATORS
BATTERY ISOLATORS ELIMINATE MULTI-BATTERY DRAIN
When 2 or more battery banks are in a charging system you
can get stuck with dead batteries and an engine that won’t start
IF YOU DON’T HAVE a battery isolator. •SOLID STATE ELECTRONICS means
no moving parts to wear out! •UNIQUE DESIGN: The anodized fin design provides
maximum heat dissipation plus all electrical parts are sealed with a moisture-proof epoxy sealant
to preserve them from the elements. •ALLOWS EACH BATTERY TO DISCHARGE AND CHARGE
ACCORDING TO ITS OWN NEEDS.
TWO-BATTERY STANDARD ISOLATOR
15776 70-Amp CS** #702-D 24
TWO-BATTERY UNIVERSAL ISOLATORS
15777 95-Amp CS** #9523A-D 24
15778 120Amp CS** #12023A-D 12
GROUP
APPLICATION INFORMATION
1
General Motors
(Delcotron)
Except Delcotron CS series alternators
(CS series used on most 1985 and newer GM vehicles).
Ford
Up to 1998.
Chrysler
All models, all years including Nippondenso externally
regulated alternators.
Jeep
Equipped with Nippondenso exterrnally regulated alternators.
Japanese Imports
With alternators using external voltage regulator or
external sensing.
Motorola
Load Handler Series or 8EM Remote Sense Series.
GROUP
General Motors
(Delcotron)
Equipped with Delcotron CS Series (most 85-93) or
SC130-D series alternators (most 93 & newer**)
Jeep
Vehicles equipped with Delcotron CS series alternator (most
1985-90).
Toyota, Honda &
Some Imports
1985 and newer equipped with Nippondenso alternator with
internal regulators or alternators with an “S” (sense) terminal.
Ford
Many 1998 and newer.
Unplugging the plug-in connector from the alternator and counting the number of holes in
the connector can identify the CS series alternator. The CS series will have three small and
one large hole. The CS130-D alternator has four pin terminals all the same size.
The SI series will have two slotted holes in the connector.
**Delco CS series alternators require a separate sense wire which is included with the connector kit. The connector
kit may or may not be included with the isolator, but is available as an accessory.
All Group 2 isolators may be used in Group 1 applications. Simply disregard the additional excitation
(“E”) terminal. A group 2 Isolator will have a colored fourth terminal indicating the “E” terminal.
MAXIMUM
2 BATTS
ALTERNATOR 1 Main,
RATING
1 Aux.
RECOMMENDED WIRE SIZE / CIRCUIT BREAKER
Up to 15'
15' to 20'
20' to 25'
25' to 30'
70 Amps
15776
#8-ga. / 50Amp
#8-ga. / 50Amp
#6-ga. / 50Amp
#6-ga. / 50Amp
95 Amps
15777
#8-ga. / 50Amp
#6-ga. / 50Amp
#4-ga. / 50Amp
#4-ga. / 50Amp
120 Amps
15778
#6-ga. / 80Amp
#4-ga. / 80Amp
#2-ga. / 80Amp
#1-ga. / 80Amp
#4-ga. / 120Amp
#2-ga. / 120Amp
#2-ga. / 120Amp
#0-ga. / 120Amp
160 Amps
240 Amps
#000 ga. / 150 Amp #000 ga. / 150 Amp #0000 ga. / 150 Amp #0000 ga. / 150 Amp
SMART SOLENOID BATTERY SEPARATOR
The Smart Solenoid is available in two models, a uni-directional charging model and a bi-directional charging model. The uni-directional model charges auxiliary battery after the primary battery
has reached at least 13.2-V. The primary battery is the priority charged battery. The bi-directional
charger charges primary and auxiliary battery after either battery has reached 13.2-V. This model
is particularly useful for motorhomes or other vehicles which are equipped with an auxiliary battery
charger, generator, inverters or solar chargers. Mounts on tow vehicle or towable.
Order #
17715
17716
6
SMART SOLENOID MODELS
13013
Up to 350 Amperes Continuous Rating
Ignition protected - safe for installation aboard
gasoline powered boats. Tactile indicator conveys knob position by feel only. Fits all Perko and
Guest low amperage battery switch hole patterns. Case design allows surface or rear panelmounting. Accepts up to 4/0 AWG (95mm2)
battery cables. • Meets American Boat and Yacht
Council (ABYC) requirements for battery
switches. • Make-before-break contact design on
9001 and 9002 models allows switching between
battery banks without power interruption.
APPLICATIONS 12533
A Group 1 Isolator will have an alternator post and up to four battery posts.
There are no colored terminals.
2
12533
E-SERIES BATTERY SWITCHES
1. Switches battery bank 1 or battery bank 2 or
battery banks 1 and 2 to all loads using one
switch.
APPLICATIONS 13013
1. Switches a single battery to a single load
group. 2. Can be used in multiples to manage
several isolated circuits including cross connecting for emergency paralleling.
SPECIFICATIONS
Inrush Rating:
0.25 sec (10 repeats)*
Cranking Rating:
9.75 sec (10 repeats)*
Intermittent Rating:
5 min (UL 1107)
Continuous Rating:
(UL 1107)
Terminal Stud Size
Terminal Stud Torque
Cable Size to Meet
Ratings***
Voltage Rating
Cable Clearance For
4/0 Cables
Case Material
9001e-9003e
1,750 Amperes DC
900 Amperes DC
600 Amperes DC
350 Amperes DC
3/8"-16 (M10)
140 in-lbs.
4/0
48 Volts DC Maximum
1.10" (27.9mm)
Reinforced
Polycarbonate
CE marked
AGENCY STANDARDS
UL Listed - UL 1107 electric power switches**
Meets UL 1500 and SAE J1171 external ignition
protection requirements
* Blue Sea Systems Engine Starting Standard
** Per Circuit
*** Reducing cable size will reduce current rating
Uni-Directional (charges starting battery, then auxiliary)
E-Series Battery Switch:
Bi-Directional (activates when either battery is charging)
12533 Selector #9001E 5
13013 Single Circuit On/Off #9003E
= Std. Carton Qty.
5
67
D
BATTERY ACCESSORIES • CONVERTERS • RELAY
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
M-SERIES BATTERY SWITCHES
300 AMPERES CONTINUOUS RATING
All switches have: • Ignition protected - Safe for installation aboard gasoline powered boats.
• Tactile textures indicate knob position by feel only. • Case design allows surface, front panel, or
rear panel mounting. • Label with international ON/OFF legends. • Ideal for marine or RV applications. • Accepts up to 4/0 AWG battery cables. • All non-corrosive marine grade metals. • Molded in
durable reinforced polycarbonate. • ICON
label set included for circuit identification.
• Removable key or knob remains positively
retained. • 3/8"-16 M10 tin-plated copper
studs for maximum conductivity and
corrosion resistance. • 7/8" Long stud
length to accept multiple cable terminals.
• Isolator cover with snap-in sections
protects rear contacts.
14548
14549
PROGRESSIVE DYNAMICS
RV & MARINE AUTOMATIC
TRANSFER RELAY SYSTEM
Generator to shore power automatic transfer
relay system features: • Heavy duty relays to prevent contact damage during high current transfer
operation. • Quick change replaceable circuit
board. • Time delay circuit board ensures generator voltage is at proper level before transfer
occurs. • Built-in strain reliefs for easy installation. • Protective cover easily snaps on or off.
• PD5110010V has pigtail AC wire connections.
APPLICATIONS (14548-14549)
1. Switches a single battery to
a single load group.
2. Multiple switches can be used to manage
several isolated circuits including cross
connecting for emergency paralleling.
12375 Automatic Transfer Relay System,
120VAC, 30Amp #PD5110010V
1
14945 Automatic Transfer Relay System,
120VAC, 50Amp #PD52V
4
SPECIFICATIONS
Inrush Rating: 0.25 sec (10 repeats)*
Cranking Rating: 9.75 sec (10 repeats)*
Intermittent Rating: 5 min (UL 1107)
Continuous Rating: (UL 1107)
Maximum Voltage Rating
Terminal Stud, Tin-Plated Copper
Terminal Stud Torque
Cable Size to Meet Ratings***
Cable Clearance For 4/0 Cables
Case Material
1,500 Amperes DC
700 Amperes DC
500 Amperes DC
300 Amperes DC
48 Volt DC
3/8" -16 (M10)
140 in-lb.
4/0 AWG
1.12" (28.4mm)
Reinforced
Polycarbonate
CE marked
AGENCY STANDARDS
UL Listed - UL 1107 electric power switches.
Meets UL 1500 and SAE J1171 external ignition
protection requirements. * Blue Sea Systems Engine Starting
Standard ** Per Circuit
*** Reducing cable size will reduce current rating
PARALLAX
POWER
SUPPLY
BATTERY DISCONNECT RELAY
14578
APPLICATION (14578)
1. Switches battery bank 1 or
battery bank 2 or battery banks 1
and 2 to all loads using one switch.
M-Series Battery Switch:
14548 Single Circuit On-Off
w/Key #6005
5
14549 Single Circuit On-Off,
w/Knob #6006
1
14578 Selector #6007
5
Prevents battery
drain during camping
and storage periods.
• Helps maintain
battery life.
• No continuous
current draw.
• 100A 12VDC
capability continuous.
• 300 amp surge.
15009 Battery Relay #BR100
POLLAK SOLENOID SWITCHES - CONTINUOUS DUTY
SPECIFICATIONS
• 6-24 VDC Systems
• Plated Steel or Phenolic Housings
• Ignition & Ground Terminals, No.10-32 Thread
• Contact Terminals 5/16"- 24 Thread
• Bracket Mounting Holes;
5/16" x 19/32",2 1 /8" on centers.
• Complete Mounting Hardware.
Starter Solenoid, Continuous Duty 85 Amps,
4 terminal, UL listed:
13753 Bulk #52-307 25
13785 Visi-Pak #52-307V 1
Starter Solenoid (Same as 52-307 except
grounded), 3 terminal, not UL listed:
13678 Bulk #52-312 50
68
1
Voltage Rating:
Features:
13753
Current Rating:
In Rush Current:
◆
Not UPS-able;
▲
6-24 VDC
12-V Continuous
Duty Solenoid Insulated,
with hardware.
Flat Bracket. Replaces:
Delco 1114218, 223;
Prestolite 15-132,133,
236, 311, SAS-4201,
4202, 4213,
5203.Except grounded
with three terminals.
Replaces Presolite
No's 15-139 SAS 4208.
85 DC Amp
150 Amp
Hazmat terms apply; LS Limited Supply
CONVERTERS/CHARGERS
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
D
ELECTRICAL
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
10129
10131
PARALLAX
500 SERIES POWER CENTERS
Parallax Power Centers - combining power
conversion, battery charging, and AC/DC
distribution - are a benchmark for RV power.
500 Series Power Centers for 50 amp/240 volt
service are the most versatile yet, with eight
AC branches, 15 DC fuse circuits, and a 50Amp
main AC breaker. Add-ons like roof air conditioning, washers and dryers are accommodated.
Extra panels are rarely needed. Filtered DC
output is ideal for electronic-based appliances,
accessories and motors. Power is free from
spikes and surges, and operation is quiet.
Smooth appliance operation and bright lighting
are two of the benefits RVers appreciate.
FCC Class B certification attests that minimal
signal interference is caused with TVs, radios
and emergency channels. c-ETL-us listed.
MODEL 555
30 AMP AC-55 AMP DC
ELECTRONIC POWER CENTER
Direct OEM Replacement Part
• 30 amp AC service with 55 amp on the DC side.
• Distribution panel accomodates a 30 amp main
AC circuit breaker. • Has a 5 AC branch circuits
and 11 DC fuse circuits. • Weights: 13.5 lbs.
• Dim.: 11-3/4” H x 14” W x 7” D.
10129 55 Amp Converter with Distribution
Panel #7155
1
55 AMP REPL. CONVERTER SECTION
• DC Output: 55 Amps. • AC Input: 120/240
Volts. • 8 AC Branches. • 15 DC Fuse Locations.
• 12-1/8” H x 12-1/4” W x 8-5/8” D. • 22 lbs.
16199 55 Amp. DC Output #555
PARALLAX
POWER
SUPPLY
7155 SOLID POWER CENTER
1
For WFCO® WF-8945 and WF-8955 Power Centers
• Direct lower section replacement.
• Weights: 4.3 lbs. • 2-year warranty.
• Dim.: 9.5” L x 7” D x 4” H.
10131 Replacement Lower Section f/7155
#081-7155-000
1
The Perfect
Power
Solution
for Smaller RV Classes.
PARALLAX POWER SUPPLY
6730 SERIES ELECTRONIC
CONVERTER/CHARGER
PARALLAX POWER SUPPLY
7300RU (REPLACEMENT UPGRADE)
Electronic Converter/Charger
Sections for Power Centers
An Easy Upgrade to Clean, Quiet Power.
• Upgrades linear power centers to electronic
performance. • Provides filtered electronic power
to existing power centers. • Power is free from
spikes and surges, and the full output rating
is available for battery charging. • Minimizes
interference with TVs, radios, and emergency
channels per FCC Class B certification.
• Quiet operation. The only sound comes from
a small cooling fan. • DC Output is 14.0 max.
volts @ no load, 13.2 volts max. at full load.
• The included fuse panel provides two 30 amp
fuses for reverse polarity battery protection and
capability up to nine DC load branch circuits.
• Two-year warranty.
Converter/Charger Lower Section & Upgrade:
18024 45 Amp. Output #7345RU 1
with AC and DC Distribution
• Filtered power is free from spikes and surges,
and the full output rating is available for battery
charging. • 30 amp DC output is ideal for smaller
RVs. • Pre-wired circuit breakers are provided:
(1) 30 amp main, (1) 20 amp branch, and
(2) 15 amp branches. • Locations for five DC
fuses (fuses not included); (1) fuse for reverse
polarity protection is included. • 13.75" W, 7" H,
5.5" D; Cut-out required: 12.75" W, 6.25" H.
Weight: 8 lbs.
7300RU sections easily install into 6300 Series
electronic power centers. A simple way
to upgrade the popular 6300, 7300RU sections.
PARALLAX POWER SUPPLY
500 SERIES REPLACEMENT
CONVERTER SECTIONS
These converter/charger sections are direct
replacements for the lower sections of Parallax
555 and 565 Power Centers. Filtered DC output
is ideal for electronic-based appliances,
accessories and motors.
12411 55 Amp. Output #7355 RU 1
REPLACEMENT
DOOR LATCH
FOR CONVERTERS
500 Series Converter/Charger Only:
16200 55 Amp. DC Output, 12 lbs
15010 30 Amp Converter #6730D 1
6
= Std. Carton Qty.
#555R
1
14985 Door Latch #13516372
69
D
CONVERTERS/CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Cords & Adapters
PARALLAX
7400 SERIES DECK-MOUNTED
CONVERTER/ CHARGER
The Most Proven Power...
Quiet, Clean, and Clear.
Model
12899
#7430 Converter/Charger
12412
#7440 Converter/Charger
18186
#7445 Converter/Charger
18187
55 Amp
#7455 Converter/Charger
65 Amp
#7465 Converter/ Charger
14399
Description
30 Amp
40 Amp
45 Amp
7300 SERIES
POWER CENTER
ELECTRONIC
CONVERTER/CHARGER
AC Input
Volts Watts
105-130
490
60Hz
105-130
670
60Hz
105-130
775
60Hz
105-130
975
60Hz
105-130
1120
60Hz
PARALLAX
POWER
SUPPLY
LINE GENERATOR
SWITCHES
MODEL ATS™ 301
DC Output
Volts
13.85 max. @ no load
13.2 min. @ full load
13.85 max. @ no load
13.2 min. @ full load
13.85 max. @ no load
13.2 min. @ full load
13.85 max. @ no load
13.2 min. @ full load
13.85 max. @ no load
13.2 min. @ full load
For 30Amp, 120-volt electrical systems —
• Allows changeover of power between shoreline
cord and generator controlled from inside the RV.
• Can be used as deck-mount or mounted to the
back of Parallax Power Centers. • Reliable electronic operation. • Generator time delay for load
stabilization. • Chatter-free operation under low
line voltage conditions. • Weight: 3.5 lbs.
• 6" W x 4-1/8" D x 4-7/16" H.
Amps
30
40
45
55
14611 ATS 301 Line Generator Switch,
65
30 Amp./120 Volt #ATS301 4
For smooth appliance
operation and bright
flicker-free lighting.
The RV Industry’s Most Popular Power Center.
Safe,
convenient
power transfer
for 50 Amp,
120/240-volt
systems
• Combines AC/DC distribution and converter/
charger in one space-efficient package. • Filtered
power is free from spikes and surges. • Minimizes
interference with TVs, radios, and emergency
channels per FCC Class B certification. • Quiet
operation. • Accommodates five AC branches
and nine DC fuse circuits (fuses and circuit
breakers not provided). The full output
rating is available for battery charging, virtually
eliminating dead or drained batteries.
• 14" W x 11.75" H x 7" D; Weight: 20 lbs.
• Two-year warranty.
The electronic converter/charger provides
MODEL ATS™ 501
With a flick of the generator switch, the
ATS 501 line generator switch from Parallax
transfers power smoothly between shoreline
power and generator/secondary power source,
regardless of line voltage conditions. ATS 501 is
engineered for superior reliability in 50 Amp,
120/240-volt electrical systems (per the new
UL Standard 1008). Electronic circuit board
design is proven in extensive cycle testing to
withstand heat and torque. The low-profile
chassis measuring just 3-1/2” high allows mounting in areas not possible with other
50 Amp transfer switches, and installation can be
made without cover removal. Manual shut-off for
time delay optimizes use with inverters.
8-3/4" W x 3-1/2" H x 11-3/4" D. 7 lbs.
reliable battery charging and filtered output.
Order #
Model
13046
#7345
14518
#7345R
13047
#7355
14517
#7355R
Description
Power Center
with 45 ADC
Converter/Charger
45 ADC
Converter/Charger
Lower Section Only
Power Center
with 55 ADC
Converter/Charger
55 ADC
Converter/Charger
Lower Section Only
AC Input
Volts Branches
DC Output
Volts
Amps
120
5
14.0 max. @ no load
13.2 max. @ full load
N/A
N/A
14.0 max. @ no load
13.2 max. @ full load
45
120
5
14.0 max. @ no load
13.2 max. @ full load
55
N/A
N/A
14.0 max. @ no load
13.2 max. @ full load
55
45
16600 50 Amp, 120/240 Volt
#ATS501
70
Switches
Safety and
Convenience
for Power Transfer.
• Filtered DC power is free from spikes and surges. • Full output rating is available for battery charging. • Minimal signal
interference with TVs, radios, and emergency channels per
FCC Class B certification. • Quiet operation. The only sound
comes from the cooling fan. • c-ETL-us listed. • Optional twostep charging provides expedient recharging and reliability
through long-term park and storage periods. • Dimensions:
4-1/8" H x 7" W x 12-3/8" L; . Weighs just 7.5 pounds
• Mounts in any position, including upside-down.
• Two-year warranty.
Order #
Box/Hatch
◆
Not UPS-able;
▲
1
Hazmat terms apply; LS Limited Supply
CONVERTERS/CHARGERS
Meters/Testers
In Section D:
Wiring
Fuses
12V Accessories
D
ELECTRICAL
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
DELTRAN BATTERY TENDER CHARGER/MAINTAINER
Battery Tender Products are perfect for storage periods and when
the RV isn't being used to maintain batteries at 100% at all times.
Also the chargers will not overcharge and boil the battery like the
chargers currently on your RV.
BATTERY TENDER®
WATERPROOF 800
BATTERY TENDER®
JUNIOR 12V-0.75A
CHARGER/
MAINTAINER
PARALLAX POWER SUPPLY
90A DECK MOUNT CONVERTER
A 90 ampere DC output Converter/Charger
with active Power Factor Correction technology!
With Power Factor Correction the ParaMode
5490 uses 120V AC input current much more
efficiently, producing 90 amperes of DC output
current, yet draws only the AC input current
previously required for a 55-65 ampere
DC output unit.
Input: 105-130V AC, 50/60 Hz, 1550W
Output: 13.6V AC, 90ADC
12” W x 12” W 4” W, 12lbs.
11045 90A Deck Mount Converter
#5490
1
The Battery
Tender Junior is much
more than a trickle charger.
It has a brain. It's lightweight, compact, and
fully automatic; very easy to use, especially in
small spaces. It will keep your battery fully
charged so that it is ready to go when you are!
• Perfect for all lead-acid, flooded or sealed
maintenance free batteries (AGM and gel cell).
• Complete 4-step charging program (Initialization, Bulk Charge, Absorption Mode, Float
Mode). • Automatically switches to float / maintenance voltage after fully charging the battery.
• If the battery voltage drops too far under load,
full charger output power resumes. • Solid state
two color LED indicates stage of charger.
• Spark proof. • Reverse polarity protected.
• 12' output cord. • 5-yr. warranty!
16847 Battery Tender® Junior, 750mA 12V
#021-0123
12
16852
SUNFORCE
12V POWER
CONVERTER GM-1200 *
• Converts 110V AC Wall Outlet into a 12V DC
Plug. • Use Your 12V Products at the Home,
Office or on the Road. • Output: 12V DC-5.8A,
Input: 100-120VAC and 50/60Hz 1.8A.
• Use with Coolers, Spotlights, Fans,Cell
Phones. • AC/DC converter, 5.8 amps.
Unit weight: 1 lb, shipping weight, 1.3 lbs. Use
only with appropriately sized products; do not
exceed 5.8 amps.
* See also 12V “ENDLESS BREEZE” FAN
(#12931 in section H)
10002 12V Power Converter, GM-1200
#55522
6
20
= Std. Carton Qty.
16849
POWER TENDER
PLUS 12V -5A
WATERPROOF, Shock & Vibration Resistant,
Lightweight (LESS THAN 4 POUNDS), compact
charger designed for either portable operation or
permanent mounting. Charges and maintains
both flooded and sealed, maintenance free,
AGM, lead acid batteries. Float / Maintenance
function maintains batteries at proper storage
voltage without the damaging effects caused by
trickled chargers. The Power Tender PLUS is
easy to use, it’s rugged, its compact, it's packed
with power, and it’s backed by the reputation of
the undisputed battery charger industry leader,
DELTRAN.
The engineers at
Deltran led the way in
innovation and convenience by introducing
the International Battery Tender® Waterproof 800. Since its introduction in 2003, it has been widely accepted
as a solid new addition to the Battery Tender®
family of charger products. This compact 800
mA battery charger has all the charge characteristics of its cousin the Battery Tender Junior.
It incorporates highly efficient surface mount
technology electronic components. The interior is completely encapsulated, protected
from shock, vibration, and moisture by an electrically insulating, thermally conductive, flame
retardant, UL recognized, synthetic epoxy
resin compound. It's tough, affordable, and a
strong, innovative battery charging solution.
This charger is no larger than a standard
computer mouse yet packs 800 millamps of pure
constant current charging power. Coupled with a
brain (IC chip), the charger will constantly monitor, charge, and then maintain your battery --even while totally submersed under water!
Perfect for all outdoor types of ATV's, watercraft,
motorcycles, boats, or anywhere water is a
threat. International universal input voltage
works anywhere in the world 100-240 AC Volts
50/60 Hz.
• "Supersmart" Technology • Spark Proof
• Short Circuit Protected • Reverse Polarity
Protected • Waterproof • Weighs only 1 Pound
• 3-yr. warranty!
16848 Battery Tender® Waterproof 800,
800MA 12V #022-0150-DL-WH
12
BATTERY TENDER PLUS 12V - 1.25A
• Microprocessor Controlled, BTP Technology
• Charges both flooded & sealed maintenance
free lead acid batteries. • Charges any size
(capacity) lead acid battery. • Reverse Polarity
Protection (VIA EXTERNAL IN-LINE FUSE).
• Complete FOUR-Step Charging Program
(Initialization, Bulk, Absorption, & Float /
Maintenance). • 2-yr. Warranty !
The Battery Tender Plus is a 1.25-amp battery
charger designed to fully charge a battery and
maintain it at proper storage voltage without
the damaging effects caused by trickle chargers.
Included is a quick connect harness for hard to
reach areas. • Temperature compensated to
ensure optimum charge voltage according to
ambient temperature. • Automa-tically switches
from full charge to float charging mode. • Battery
Tender at 1.25-amp will charge as fast or faster
than any 3-amp charger available. • Reverse
Polarity Protection to ensure user safety. Red &
Green Lights Alternately Flash in this condition.
• Complete 4-step charging program (Initialization, Bulk Charge, Absorption Mode, Float
Mode). • 10-yr. warranty!
16852 Power Tender® Plus, 5.0A 12V
16849 Battery Tender® Plus, 1.25A 12V
#022-0157-1
6
#021-0128
12
71
D
SOLAR CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
COLEMAN® SOLAR BATTERY
MAINTAINERS &TRICKLE CHARGERS
Cords & Adapters
Box/Hatch
Switches
14722 in use
Amorphous Solar Panels Charge In All Weather Conditions – Even On Cloudy Days!
Use the sun’s energy to maintain the charge of 12V batteries which power
motorcycles, personal water crafts, ATV's, snowmobiles. Fully weatherproof.
Easy connection to the battery. Maintenance free. Built-in overcharge /
discharge protection. Works in all daylight conditions. Maximum power output :
1 watt. Temperature range -40 to 176 F. Dim.: 19-1/2" L x 5-7/8" W x
1-1/2" H (49.5 x 15 x 4 cm). Weight: 1.6 lbs (0.72Kg).
14722 Coleman® 1 Watt Solar Power Sports Charger
#58013
14722
24
14818 in use
Maintain 12V battery charge by using the sun’s power for car’s, SUV’s,
ATV’s. Battery clamps Included. Also includes 12V DC plug to plug
into 12V car plug. Mounts on Windshield with Included Suction Cups.
Made of Durable ABS Plastic & Amorphous Solar Cell.
Maintenance free, charges in all weather conditions.
Temperature range -40 to 176 F. Max Output 2 Watts
133 Mah. Dim.: 19-5/8" L x 6-1/2" W x 1-1/8" H
(50 x 16.5 x 3 cm). Weight: 1.8 lbs (0.82Kg).
14818
14818 Coleman® 2 Watt Solar Battery Maintainer
#58012
24
Trickle charge and maintain your 12V battery. Completely weatherproof,
use indoors or outdoors. Built-in blocking diode protects battery discharge
at night. Temperature range -40 to 176º F. Max output 6W 400 Mah.
Includes: 4 Pre-cut holes for easy installation; 4 Stainless Steel
Screws; 9.5 Ft wire; 12V DC Plug; Battery Clamps; Quick Connect
technology. Dim.: 18" L x 1-1/2" W x 14-1/2" H (45 x 3 x 36 cm).
Weight: 4.6 lbs (2.1Kg)
14834 in use
14834
14834 Coleman® 6 Watt Solar Battery Trickle Charger
#58022
12
Works with Automobiles, RV’s, Boats,Tractors, ATVs, Electric
Fences, Deer Feeders, Telemetry, and more. Maintenance
Free/Easy Installation. Works in All Weather Conditions.
Built-in Blocking Diode Protects Battery Discharge at Night.
Made of Durable ABS Plastic with an Amorphous Solar Cell.
Temperature Range: -40° to 176° F. Max Output 18 Watts
1.2 Amp. Dim.: 38" L x 13-1/2" W x 1-1/2" H
(96.52 x 34.29 x 3.81 cm).
Weight: 10.8 lbs (4.90Kg).
14841 Coleman® 18 Watt Solar Battery Charger
#58032
14841
14658
SOLAR
VENT
WITH LIGHT
4
Same as above but also includes a 7 Amp
controller. Includes: • Pre-cut Holes for
Easy Installation. • 4 Stainless Steel Screws.
• Battery Clamps. • CLA Adapter. • 12ft Wire.
• 7 Amp Charge Controller.
14658 Coleman® 18 Watt Solar Battery Charging Kit
(Includes a 7 Amp Controller) #58033
4
NOTE:
Solar panels 15W and above can be hooked together
to increase the rate at which your 12V batteries are being charged.
Both amorphous and crystalline panels can also be hooked together.
It is important however to correctly size the charge controller. The general
rule is 1 Amp per 15 Watts of solar power. For example, the Coast kit
# 14658 comes with a 7 Amp charge controller, 7 x 15 equals 105 therefore
this controller can handle up to 105 watts of solar power (or in other words
5 of the 18W panels). Coast # 14648 (30 Amp Controller) can handle
up to 450 Watts of solar power (30 x 15 equals 450).
72
Powered by
sunlight. Easy installation,
no wires required. Silent secure ventilation.
No running costs. Helps reduce humidity.
Can be mounted in polycarbonate, glass, wood,
metal and more. Dim.: 9.5" L x 9.5" W x 3.5" H
(24 x 24 x 8.89 cm). Weight: 2.2 lbs (1Kg).
14843 Solar Stainless Steel Vent
#81300
6
7 Amp Charge
Controller Included
◆
Not UPS-able;
▲
Hazmat terms apply; LS Limited Supply
SOLAR CHARGERS
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
D
ELECTRICAL
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
COLEMAN®
SOLAR KITS
Complete solar power generator kit. Create power for homes, boats,
RVs, backup and remote power use. Portable & easy setup. Works with
12V & 110V appliances. Weatherproof and maintenance free. Works in
all daylight conditions. Includes rugged metal frame, junction box for
multiple panel connection, 12V DC plug and alligator battery clamps,
mounting screws and extra wiring, 12V female socket for powering
12V products, 200W inverter and 7 Amp charge controller. There are
3 panels in the 55 Watt kit (18.3 watts each). The shipping dimensions
are 11” x 44-1/4” x 15-1/2”. Weight: 60 lbs (27.2Kg).
14716 Coleman® 55 Watt Solar Kit
#58050
14716
1
Generate power for homes, boats, RVs, backup
and remote power use. High efficiency
monocrystalline solar cells. Weatherproof.
Mounting hardware & wiring included.
Ideal for areas with high sun exposure.
Also refer to page 71 for 12V Power Converter
from Sunforce Products.
14717
60W MONOCRYSTALLINE
SOLAR CHARGING KIT WITH
A 7 AMP CHARGE CONTROLLER*
85-W Solar Panel.
Dim.: 51” L x 26” W x 3-1/2” H
(129 x 68 x 9 cm). Weight: 24.2 lbs (11Kg).
Now includes a 7 amp charge controller
at the same great price!
Includes 60 Watt Solar Module, voltage tester, brackets,
wiring and screws. 42.6" x 19" x 2.4". Includes a 7 Amp
charge controller (Mfr#60012) for free!
14717 Coleman® 85 Watt Monocrystalline
Solar Panel #38850 ◆ 1
130-W Solar Panel.
Dim.: 59" L x 26-3/4" W x 2-3/4" H
(150 x 68 x 7 cm). Weight: 34.2 lbs (15.5Kg).
10132 60W Solar Charging Kit
with a 7 Amp charge controller
#37015
1
14721 Coleman® 130 Watt Monocrystalline
Solar Panel #38110 ◆ 1
14721
* The more panels you have, the more
appliances you can help run and the quicker
you can recharge your 12 volt bank of batteries.
COLEMAN®
CHARGE
CONTROLLERS
14642
14648
(Same as above
but also includes an
LED digital display)
14600
Prevents overcharging of 12 Volt batteries.
Maintenance free protection of your solar
panel and batteries. Maintains 12 Volt batteries
in fully charged state. LED indicators indicate
charging and fully charged battery states.
Dim.: 7-5/8" L x 4-5/8" W x 2-1/4" H
(19.5 x 12 x 5.5 cm).
14600 7 Amp Solar Charge Controller
#68012
6
24
= Std. Carton Qty.
Protect Battery from Overcharge and Discharge.
For Use with 12 Volt Solar Panels and Batteries
Only. Handles up to 30 Amps of Array Current.
Handles up to 450 Watts of Solar Power. Maintenance Free Protection of Your Solar Panel and
Batteries. Maintains Battery Voltage. Maintain
12V Batteries in a Fully Charged State.
Dim.: 8-3/4" L x 10-1/4" W x 2-5/8" H
(22.5 x 26 x 6.5 cm).
14642 30 Amp Solar Charge Controller
#68022
20
14648 30 Amp Solar Charge Controller
with an LED digital display
#68032
20
FOR MORE INFORMATION
PLEASE VISIT
WWW.SUNFORCEPRODUCTS.COM
73
D
CONVERTERS/CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Inteli-Power Series
Converters and Power
Centers from Progressive
Dynamics have our
exclusive Charge Wizard®
technology. It constantly
monitors voltage status and
manages your RV battery and
extends the life.
Cords & Adapters
Box/Hatch
Switches
9100 Series
Inteli-Power™ Converters
provide safe, reliable,
filtered DC power to all
12-Volt lighting and appliance circuits. The built in
Total Charge Management System (TCMS) allows
for easy addition of the optional Charge Wizard,®
a microprocessor-controller that constantly
monitors the RV battery status and automatically
selects one of four charging modes: Boost Mode
- (14.4) to quickly bring the battery to 90% of full
charge, Normal Mode - (13.6) safely completes
the charge, Storage Mode - (13.2), automatically
activates after 30 hours of non-use or Desulfation
Mode - (14.4), for 15 minutes every 21 hours
to prevent battery stratification and sulfation
(the leading cause of battery failure).
Standard features on Inteli-Power
Converter and Power Centers:
• Reverse battery protection – prevents damage from
improper battery lead connection.
• Filtered DC power delivery – provides safe and
reliable service.
• Electronic current limiting – automatically reduces
output voltage when maximum capacity is reached.
• Low line voltage protection – protects appliance from
damaging low voltage irregularities.
Input: 105-130 VAC, Output: 13.6 VDC
Dimensions: 4.5"H x 8.25"L x 7.25"W,Weight: 4 lbs.
• Our Inteli-Power Series™ models – Can recharge your
RV battery to 90% efficiency in just a couple of hours
using ChargeWizard technology.
12043 30 Amps #PD9130V
6
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 4.5"H x 8.25"L x 7.25"W, Weight: 4.5 lbs.
• Variable speed intelligent cooling fan – automatically
monitors unit temperature and activates fan at
required speed.
11727 40 Amps #PD9140AV
• Hi voltage protection – protects unit from spikes or
surges of voltage over 135 Volts.
6
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 4.5"H x 8.25"L x 7.25"W, Weight: 4.5 lbs.
• Automatic thermal shutdown – activates when
unit temperature exceeds 150°F and protects unit
from damage due to excessive heat.
12438 45 Amps #PD9145AV
6
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 3.6"H x 8"L x 9"W, Weight: 5.8 lbs.
11728 60 Amps #PD9160AV
6
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 3.6"H x 11.5"L x 9"W, Weight: 7.5 lbs.
12045 80 Amps #PD9180V
6
Progressive Dynamics, Inc.
Plug-in a TCMS Charge Wizard®
The intelligent way to automatically
charge batteries! Progressive
Dynamics’ Charge Wizard is a powerful microprocessor that turns your
Inteli-Power 9100 Converter into an intelligent and
completely automatic 12-VOLT charging system.
11726 Charge Wizard #PD9105V
74
◆
Not UPS-able;
▲
6
Hazmat terms apply; LS Limited Supply
CONVERTERS/CHARGERS
In Section D:
Meters/Testers
Wiring
Fuses
Inteli-Power 9200™ Series Converters with
BUILT-IN Charge Wizard® will recharge your
RV’s battery to 90% in 2-3 hours. Many
converters only have one charging mode,
13.6 VOLTS, which can result in battery boil-off.
The 9200 Series converters have FOUR
charging modes: BOOST (14.4 VOLTS),
NORMAL (13.6 VOLTS), STORAGE (13.2
Volts) and DESULFATION (13.2 VOLTS with
a 15 minute 14.4-VOLT burst every 21 hours).
12V Accessories
Battery Accessories
Storage Mode – Maintains charge with
minimal gassing or water loss during periods
of non-use or storage.
14391 60 Amps #PD9260CV
1
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 3.6"H x 8"L x 9"W, Weight: 5.8 lbs.
1
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 3.6"H x 11.5"L x 9"W, Weight: 7.5 lbs.
14393 80 Amps #PD9280V
Box/Hatch
Switches
4
4
4
10472 Distribution Panel 45 Amp. Mighty Mini #PD4045KV
10450 Replacement Converter 45 Amp. #PD4045CSV 6
6
6
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 3.6"H x 8"L x 9"W, Weight: 5.8 lbs.
14392 70 Amps #PD9270V
Cords & Adapters
The PD4000 Series "Mighty Mini", is a compact All-In-One AC/DC
Distribution Panel and Inteli-Power Converter with built-in Charge
Wizard®. Compact & lightweight, the PD4000, has front access to a
large wiring compartment. The Snap Lock cover stays shut while
traveling yet opens with a touch. The AC Distribution Panel is
rated for 120 VAC at 30 AMPS. The DC section has up to
12 branch fuse holders. The ”Mighty Mini” is available in
a 45 AMP model. Dim.: 12.25”W x 8.875”H x 5.625”D.
Note: 30 AMP main breaker and AC breakers are not included
and shown for reference only.
Normal Mode – Safely completes the charge
or maintains the charge.
14390 45 Amps #PD9245CV
Chargers & Inverters
Inteli-Power 4600™ Series Lower Section Replacement/
Upgrade Converters for RV power systems are as close
as you can get to a “universal” replacement. The 4600
Series Converters can be used to replace the lower
section converters in Magnatec, Parallax and WFCO®
power centers. They are MADE IN AMERICA and have
the same impressive quality, performance, reliability and
multi-patented features, including the incredible
CHARGE WIZARD® built-in. The Inteli-Power 4600™
Series Converters are WHAT YOU NEED FOR
RELIABLE 12 VOLT POWER!
Size: 13.375”W x 8.125”D x 5.875”H
17382 35 Amp Converter/Charger Repl. Section #PD4635
17383 45 Amp Converter/Charger Repl. Section #PD4645
17385 55 Amp Converter/Charger Repl. Section #PD4655
Boost Mode – Rapidly brings RV battery up to
90% of full charge.
Input: 105-130 VAC, Output: 13.6 VDC
Dim.: 4.5"H x 8.25"L x 7.25"W, Weight: 4.5 lbs.
D
ELECTRICAL
1
Retail Model Pendant
Plugs into the accessory port
to show charger/converter status and
allows for manual mode selection. The
Pendant is included with all retail models.
The PD4500 Series is
the Ultimate All-In-One
AC/DC Distribution
Panel and Inteli-Power
Converter/Charger.
The AC Distribution
Panel is rated for
240 VAC @ 50 AMPS.
The DC section has up to 18 branch
fuse holders. Available with a 60 AMP Inteli-Power
Converter, it’s the largest converter/ charger
available in the industry. The patented built-in
Charge Wizard® reduces RV battery recharge
time and increases battery life, while reducing
battery sulfation and maintenance problems.
Panel Size: 11.85”W x 14.125”H x 8.5”D.
Note: AC breakers not included and shown
for reference only.
S/O60 Amp Converter/Charger Repl. Section
#PD4560CSV
17392 60 Amp All In One Converter/AC/DC/
Panel #PD4560K12LV
1
The PD4300 Series
AC/DC Distribution
Panel has front access
to a large wiring
compartment and a
snap lock cover that
stays shut while
traveling yet opens with
a touch. The PD4300 is rated for 120 VAC at
30 AMPS, is available with either a 45 or 60 AMP
Inteli-Power converter and features a status
indicator and mode control button for the built-In
Charge Wizard®. The DC panel accommodates
up to 12 branch fuse holders with maximum rating
of 20 AMPS each.
Dim.: 11.85”W x 14.125”H x 8.5”D.
Note: 30 AMP main breaker and AC breakers are
not included and shown for reference only.
4300 Series Power Converter :
10501 45 Amp #PD4345K12LV 1
10515 60 Amp #PD4360K12LV 1
S/ORetail Model Pendant #PD92201
6
= Std. Carton Qty.
75
D
INVERTERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
DC-AC Modified Sine Wave Inverters - SAM Series
Modified sine wave AC-DC power inverters are ideal for powering office equipment, television,
power tools and lighting systems from your car, truck, boat, RV, solar system, or battery.
14076
14077
• USB charging port:
5 VDC, 500 mA.
• Compact design with
cigar lighter plug included.
• Load controlled cooling fan.
• Low battery input alarm.
• Universal protection circuit:
thermal, battery, overload,
short circuit, earth fault.
• Soft start technology.
• Cool surface technology.
• Low interference technology.
250 Watt
Modified
Sine Wave Inverter
100 Watt
Modified
Sine Wave Inverter
• USB charging port:
5 VDC, 500 mA.
• Compact design
with cigar lighter plug.
• Protection: low battery,
over temperature,
over voltage, overload,
short circuit, earth fault.
• LED indicator
for power status.
14078
450 Watt Modified
Sine Wave Inverter
• USB charging port: 5 VDC, 500 mA.
• Compact design with cigar
lighter plug included.
• Load controlled cooling fan.
• Low battery input alarm.
• Universal protection circuit:
thermal, battery, overload,
short circuit, earth fault.
• Soft start technology.
• Cool surface technology.
• Low interference technology.
14079
800 Watt Modified
Sine Wave Inverter
• Same great features as the
450W Power Inverter but
without the cigar lighter plug.
14232
2000 and 3000 Watt
Modified Sine Wave Inverters
1000 and 1500 Watt
Modified Sine Wave Inverters
• Compact design.
• Load controlled cooling fan.
• Low battery input alarm.
• Universal protection circuit:
thermal, battery, overload,
short circuit, earth fault .
• Soft start technology.
• Cool surface technology.
• Low interference technology.
• Compact design.
• Load controlled cooling fan.
• Low battery input alarm.
• Universal protection circuit:
thermal, battery, overload,
short circuit, earth fault.
• Soft start technology.
• Cool surface technology.
• Low interference technology.
14158
Also see p62
for fuse assemblies
14183
Order #
14076
14077
14078
14079
14232
14080
14158
14183
Model
SAM-100-12
SAM-250-12
SAM-450-12
SAM-800-12
SAM-1000-12
SAM-1500-12
SAM-2000-12
SAM-3000-12
Description
100W Power Inverter
250W Power Inverter
450W Power Inverter
800W Power Inverter
1000W Power Inverter
1500W Power Inverter
14080
DC
Input
12 VDC
12 VDC
2000W Power Inverter
12 VDC
3000W Power Inverter
Inverter Remote Control for
12 VDC
14075 SAM-RC
SAM-1000, 1500, 2000, 3000
All SAM-Series Inverters are Listed by ETL to UL Safety Standard 458.
AC
Output
115 VAC
115 VAC
115 VAC
-
Watts
Weight
(lbs)
Dimensions
L" x W" x H"
100W
0.3
5.1 x 2.5 x 1.5
250W
0.9
5.9 x 4.5 x 1.8
450W
1.3
6.0 x 6.1 x 2.2
800W
2.9
8.6 x 7.1 x 2.4
1000W
3.7
9.8 x 7.1 x 2.3
1500W
7.1
11.1 x 8.0 x 3.3
2000W
8.5
13.6 x 8.0 x 3.3
3000W
11.8
16.5 x 8.0 x 3.3
-
-
4.5 x 2.75
AC
Receptacle
Warranty
One
2 Year
Two
2 Year
Three
2 Year
-
2 Year
Price
• 10 ft of cable with 8P Modular Connector (RJ45).
• Bar Meter Monitor for battery charge level and output power.
• LED indicator lights for: Over voltage protection, under voltage
protection, over temperature protection, and over load protection.
14075
76
◆
Not UPS-able;
▲
Hazmat terms apply; LS Limited Supply
INVERTERS
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
DC-AC Pure Sine
Wave Inverters
Battery Accessories
Chargers & Inverters
• Rated at Continuous Output Rating.
• Economically Priced. • Compact, space saving design.
• High Performance, High Surge Power.
• True Sine Wave Output for sensitive loads.
• Samlex “Soft Start” and “Low Interference” Technology.
• 300 and 600 watt models include USB charging port.
• Universal Protection Circuit: Thermal, battery, overload,
short circuit, and earth fault.
• Backed with 2-yr. limited Warranty
by one of the world's leading
inverter manufacturers.
Box/Hatch
Switches
14433
DC
Input
Description
14474
14510
17122
NEW!
Remote control panel with informative LCD window and
wiring is Included at no extra charge with all
1000W, 1500W and 2000W models (see bellow).
Model
Cords & Adapters
High Efficiency microprocessor controlled Pure Sine Wave DC-AC inverters.
Features include overload, short circuit, over-temperature, under & over voltage
protections, low power saving mode to conserve energy. FCC approved.
Samlex SSW Series Pure Sine Wave Inverters offer industry leading features
and are ideal for powering office equipment, television, DVD, Video Games,
battery chargers and other sensitive loads from your car, truck, boat, RV, or
Solar System batteries. Value priced and rated at true continuous output,
the Samlex SSW series is the simple choice whenever and
wherever you need reliable, true sine wave power.
Order #
D
ELECTRICAL
14536
AC
Output
Watts
350W
14433 SSW-350-12A 350W Pure Sine Wave Inverter
12 VDC
115 VAC
600W
14474 SSW-600-12A 600W Pure Sine Wave Inverter
1000W
14510 SSW-1000-12A 1000W Pure Sine Wave Inverter
12 VDC
115 VAC 1500W
17122 SSW-1500-12A 1500W Pure Sine Wave Inverter
2000W
14536 SSW-2000-12A 2000W Pure Sine Wave Inverter
SSW Series Inverters are Pure Sine Wave and are Listed by ETL to UL Safety Standard 458.
Cool surface technology.
Weight
(lbs)
Dimensions
L" x W" x H"
1.5
8 x 6.2 x 2.2
2
9.2 x 6.2 x 2.3
5.7
10.6 x 8.9 x 3.5
7.1
12.2 x 8.9 x 3.5
8.4
12.4 x 8.9 x 3.5
AC
Outlets
Two
(Standard
NA outlet)
Two
(NA GFCI
outlet)
Warranty
Price
2 Year
2 Year
NA stands for North American
A battery charger,
Pure Sine Wave Inverter Chargers are heavy-duty inverters generating a pure sinusoidal
an inverter and
from a 12V battery bank with built-in AC charger & Transfer Relay for UPS function.
a transfer switch –
all in one device. Samlex’s Generation 4 InverCharge
SA-3000K-112 Pure Sine Wave –
combines three devices into one for convenience and efficiency.
G4-2012A
Pure Sine Wave
Inverter-charger
ETL listing
to UL 1741 and
UL 458 (pending)
• Reliable,
Durable and
Economical
Power for Grid and
Mobile Applications.
• Microprocessor based
Inverter/Charger provides
Ultra-clean pure sine wave output
with less than 5% total harmonic
distortion. • Surge power. • Low sleep
mode power consumption of less than 5W.
• Phase & frequency synchronization option for seamless transfer times. • Programmable 100 A, 3 stage battery charger with
optional Equalization mode. • Intelligent design allows charger
to operate in parallel with Solar or Wind powered chargers.
• Control panel with large LCD and can be detached for use as
a remote control. • Safe and Reliable ETL listed to UL standards
458 for mobile use and UL 1741 for distributed power installations (pending). • Easy to install, easy to maintain, and
built for years of reliable service. 2000W continuous power.
• 18.7” L x 8.6” W x 7.3” H, weighs 51 lbs. • 2-yr. warranty.
Order #
6
Model
Description
14546 G4-2012A
2000W PSW
Inverter/Charger
= Std. Carton Qty.
wave
DC-AC Power Inverter,
12 VDC - 110 VAC
High performance commercial grade
pure sine-wave inverter
• Power ON / OFF remote control
available (Models S-R6-12,
S-R6-24, S-R8 sold separately).
• Isolated input and output.
• Load controlled cooling fan.
• Advanced microprocessor design.
• Output frequency 50 / 60 Hz switch selectable.
• Power saving mode to conserve energy. • Protections: overload / short circuit, reverse polarity (fuse),
over / under input voltage, over temperature. • Tri-color indicators display input, output level & failure status. • True sine wave output
(THD < 3%). • 3000-watt maximum continuous power, 6000-watt surge capacity.
• Applications: Home and Office appliances, Power tools and Portable
equipments, Vehicle, Yacht and Solar power systems ...etc.
• 17.8” L x 8.2” W x 6.5” H, weighs 22 lbs. • 2-yr. warranty.
Order #
Model
Description
14547 SA-3000K-112 3000W Pure Sine Wave Inverter
AC
Outlets
Price
Two
Price
77
D
INVERTERS & ACCESSORIES • CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
™
Xantrex
17178;
Max. 1000W
inverter
on 12V DC
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
PROsine™ Inverter and
Inverter/Chargers
Why upgrade to true sine wave?
True sine wave inverters eliminate incompatibility and performance issues - such as
lines on TV screens - by supplying electricity that is the same or better quality than
the utility power supplied to your home.
Benefits of power factor corrected
charging:
17352;
Max. 3500W
inverter
on 12V DC
NEW!
SAMLEX AMERICA
INVERTER INSTALLATION KITS
PROsine™ inverter/chargers use power factor corrected charging to minimize
the AC amp draw of the charger, reducing nuisance tripping on shore power
breakers. Power factor corrected charging converts the AC input power more
effectively, requiring significantly less AC input current to produce the same high
output charge current.
Samlex Solar’s Inverter Installation Kits are
designed to protect your inverter and loads from
battery short circuit fault that could result in
severe damage to the inverter and nearby objects.
INSTALLATION COMPONENTS
FOR INVERTER/CHARGER SYSTEMS
100 AMP INVERTER INSTALLATION KIT
The DC-1000-KIT is design for use with inverters
ranging from 600W to 1000W on 12VDC and
600W to 2000W on 24VDC.
Xantrex
PROsine™ 1800 True Sine
Wave Inverter
17178 100 Amp Inverter Installation Kit ;
Contains:1 x Fuse Assembly - DC-FA-100,
1 x 10 Ft AWG# 4 DLO Positive Cable,
1 x 10 Ft AWG# 4 DLO Negative Cable
(pictured) #DC-1000-KIT 5
200 AMP INVERTER INSTALLATION KIT
The DC-2000-KIT is design for use with inverters
ranging from 1000W to 2000W on 12VDC and
2000W to 3000W on 24VDC..
17285 200 Amp Inverter Installation Kit;
Xantrex 200A Class T Fuse
•
•
•
•
True sine wave output
1800 watt inverter (2900W surge)
Includes removable LCD display
Remote interface kit accessory available for
mounting remotely
• Options include hardwire with 15 A transfer
switch or dual GFCI AC outlet models
• Approved to the UL 458 regulatory standard
Recommended for:
• Freedom 458 10 – 12 and 15 – 12
• PROsine 1000/1800
• PROwatt 1000 and 1750
Xantrex 300A Class T Fuse
Recommended for:
• Freedom 458, 20 – 12 and 25 – 12
• Prosine 2.0
Contains:1 x Fuse Assembly - DC-FA-100,
1 x 10 Ft AWG# 4 DLO Positive Cable,
1 x 10 Ft AWG# 4 DLO Negative Cable)
#DC-2000-KIT 5
300 AMP INVERTER INSTALLATION KIT
The DC-3000-KIT is design for use with inverters
ranging from 2000W to 2500W on 12VDC and
2000W to 3000W on 24VDC.
17351 300 Amp Inverter Installation Kit;
Contains:1 x Fuse Assembly - DC-FA-300,
1 x 10 Ft AWG# 2/0 DLO Positive Cable,
1 x 10 Ft AWG# 2/0 DLO Negative Cable
#DC-2500-KIT 3
400 AMP INVERTER INSTALLATION KIT
Order #
Description
BuiltContinu- Surge Peak Char
AC
ger Dimensions Weight ConnecIn
ous
Out- OutRating
L"
x
W"
x
H"
Trans
Power
put put
tion
fer
Price
15.4 x
PROsine™ 1800
18584 with Hardwire and 1800 W 2900 W 45 A N/A
11 x
16.5 lb Hardwire 15A
4.5
Transfer switch
11815 Xantrex 200 Amp Fuse Kit Class T Fuse with block and stud connectors #TFB200
11816 Xantrex 300 Amp Fuse Kit Class T Fuse with block and stud connectors #TFB300
All items include Remote & 24 Month Warranty
The DC-3500-KIT is design for use with inverters
ranging from 2500W to 3500W on 12VDC and
4000W to 6000W on 24VDC.
17352 400 Amp Inverter Installation Kit;
Contains:1 x Fuse Block - CFB2-400,
1 x 10 Ft AWG# 4/0 DLO Positive Cable,
1 x 10 Ft AWG# 4/0 DLO Negative Cable
(pictured) #DC-3500-KIT 3
78
www.xantrex.com
◆
Not UPS-able;
▲
Hazmat terms apply; LS Limited Supply
INVERTERS/CHARGERS
In Section D:
Meters/Testers
Wiring
™
Xantrex
Fuses
12V Accessories
D
ELECTRICAL
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
Freedom Inverter/Charger Series
Trusted Inverter/Charger solutions with multi-stage charging and high surge capability
Freedom 458 2000 & 2500 Inverter/Chargers:
Freedom SW 2000 & 3000
Inverter/Chargers:
• Modified sine wave AC runs most
equipment. • Three stage battery
charger recharges batteries
quickly while protecting your battery bank. • Programmable front
panel and LED indicators. • Temperature sensitive charging provides optimal care of all types of
deep cycle batteries. • Built-in 30
amp transfer switch automatically
transfers between inverter power
and incoming AC power. • Power sharing prevents nuisance tripping
of shore power breaker. • Customized settings can be programmed
with the Xantrex Freedom Basic Remote or Xantrex Link 1000 panel.
• Option of dual input and dual output connections for easy installation
• 30 month warranty. • Approved to the UL 458 regulatory standard.
Available in two models (2000 and 3000
watts), the Freedom SW Inverter/Charger
provides utility-grade sine wave output to
meet power needs of all types of marine and
recreational vehicle applications. The Freedom SW 2000 offers industry standard features
at a very competitive price whereas the Freedom SW 3000
is packed with features and offers premium performance. • Power
factor corrected, temperature compensated, multi-stage charging. • Built-in
transfer switch automatically transfers between inverter power and incoming
AC utility power. • Wide operating temperature
range. • 3000 W model: Full inverter and charger
output up-to 104°F (40°C). • 3000 W model:
Dual input/dual output interface.
With filtered modified sine wave output, Freedom inverter/chargers run
virtually anything, from office equipment to household appliances and electronics. Temperature controlled multi-stage charging ensures that your batteries are recharged quickly when supplied with electricity from your RV’s
generator or campground hookup. Automatic low/high DC voltage shutdown
and other safety features help to protect your expensive deep-cycle batteries from excessive depletion.
For inverter/charger control and basic system monitoring, use the Freedom
Basic Remote. For advanced battery monitoring and remote control,
Freedom 458 systems can be paired with optional Link 1000 remote panel.
Automatic Generator Start (#11029) –
Designed for use with System Control Panel, the
Automatic Generator Start is compatible with the
NEW Freedom SW 3000 Inverter/Charger, RS and
MS Series Inverter/Chargers. It works with popular
generator brands such as Onan, Kohler, Westerbeke, Northern Lights, Generac, and Powertech.
11029
System Control Panel (#11002) – Designed to operate with the NEW
Freedom SW 3000 Inverter/Charger. Compatible with MS and RS Series
Inverter/Chargers. The System Control Panel (SCP) features a
graphical, backlit LCD screen that displays system configuration
and diagnostic information in one central location. Large keypad
buttons, an intuitive onscreen menu system, and plain text status
messages make it easy to configure and operate. By providing basic
controls for other devices connected to the network, the SCP
reduces the complexity of separate control panels for each device.
Order #
Description
Freedom
HF1000 & 1800
Inverter/Chargers:
The Freedom HF is available in two sizes: 1000
watts with a 20-amp
charger and 1800 watts
with a 40-amp charger. Both Freedom HF models are designed for
demanding marine and RV conditions. Temperature-controlled
multistage charging ensures that your batteries are recharged
safely and efficiently. Both models include an automatic transfer
switch and a detachable digital remote control panel display
that provides precise system information and can be mounted
wherever you require the information. Features: • Designed to
power demanding loads such as microwave ovens, TVs, DVD
players, small appliances and other electronic equipment.
• Removable digital display to provide system status.
• Automatic three-stage battery charger. • Designed to be hardwired using a terminal strip, or by connecting AC through GFCI
receptacles (included). • Built-in 30-amp relay to automatically
transfer between inverter power and incoming
AC utility power. Protection Features: • Battery
over-voltage and under-voltage protection.
• Over-temperature shutdown. • Automatic
overload protection. • Short-circuit protection.
• Ground-fault protection. • ETL listed for use
11002
in mobile RV and marine applications.
POWER AC
Continuous
Surge
Charger
Dimensions
Weight
Output
10 lb
Single
Double
12.8 lb
Single
Double
45 lb
Single
Single
50 lb
71 lb
15.25”L x
13.5”W x 7.75”H 72 lb
Dual
Single
Dual
Dual
Single
Dual
16922
Freedom HF 1000
1000 W
2000 W
20 A
4.2”H x 9.5”W x
15.5”L
16923
Freedom HF 1800
1800 W
3600 W
40 A
4.2”H x 9.5”W x
18”L
11803
11804
10979
10987
11002
11029
Freedom 458 20 12
2000 W
50 A
100 A
62.5 A
4000 W
6000 W
130 A
100 A
150 A
Freedom 458 25 12 D/D
2500 W
Freedom SW 2000
2000 W
Freedom SW 3000
3000 W
Freedom SW 3000: Full-featured Remotes*
Freedom SW 3000: Automatic Generator Start*
AC Connection
Input
14" L x 11.5" W x
7.75" H
Price
www.xantrex.com
6
= Std. Carton Qty.
79
D
INVERTERS/BATTERY CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
TrueCharge2 Battery Chargers
™
Xantrex
The difference between charging your battery and just thinking you did!
TrueCharge2 Battery Chargers 20A & 40A, 12-Volt
In addition to meeting global safety and regulatory standards, TRUECHARGE2 Battery Chargers
feature low electrical interference and superior, efficient, power factor corrected multistage
charging. TRUECHARGE2 Battery Chargers can be mounted virtually anywhere, given their unique
drip-proof design. With certified ignition protection, even a gasoline engine room is an alternative
for installation*. Trouble-free installation is ensured with easy-to-access AC and DC wiring
compartments and reverse-polarity battery protection.
TRUECHARGE™ 2
Battery Charger
Designed primarily for marine, RV and commercial applications worldwide, TRUECHARGE2
Battery Chargers are unmatched for reliability. Available in two 12-volt models, they are versatile
enough to be used in a wide variety of conditions and locations. Auto-ranging AC input voltage
capability (90 - 265 volts AC) makes traveling abroad and handling poor-quality power a breeze.
The easy-to-read display can be augmented with an optional remote panel.
Redesigned, High Performance, Worldwide
Charging Xantrex TRUECHARGE™2 Battery
Chargers lead the industry with a small footprint
and ultra-compact design.
Order #
www.xantrex.com
Charge
Current Installation
Description
DC
Output
17928 TrueCharge2 20A-12V 20 amps
hardwire
Three
17860 TrueCharge2 40A-12V 40 amps
hardwire
Three
Battery
Type
AGM, gel,
flooded, Pb-Ca
AGM, gel,
flooded, Pb-Ca
Temperature
Compensation
manual switch, or optional
remote auto sensor
manual switch, or optional
remote auto sensor
Dimensions
H" x W" x L"
Weight Warranty
2.8 x 6.7 x 9.8
4.8 lb.
2 Year.
2.8 x 6.7 x 9.8
4.8 lb.
2 Year.
Price†
TRUECHARGE2 products accept 90 to 265 VAC, 47/63 Hz input. * Xantrex recommends, however, that it is safest not to install electrical equipment in these areas.
™
Xantrex
PROwatt SW Inverters
The PROwatt SW series inverters provide true sine wave AC power to operate electronics
including entertainment systems, variable speed power tools, appliances and much more.
With high surge capability, it provides the necessary current to startup demanding electrical loads.
• Available in three power levels: 600 watts, 1000 watts and 2000 watts.
• Built-in digital display for DC volts and output power.
• Built-in USB port to power USB-powered devices.
• Dual GFCI AC receptacles for safe operation.
• Industry standard protection features such as low voltage shutdown (10.5 Vdc),
low voltage alarm (11.0 Vdc), over-voltage protection (15.5 Vdc), over load
and over temperature shutdown and ground fault protection.
• Optional On/Off Remote Control Panel
10689
10693
Order #
Description
Max AC
Surge
DC
Power Capacity Connection
10678 Prowatt SW 600 Inverter
600W
1200W
hardwire
10689 Prowatt SW 1000 Inverter
1000W
2000W
hardwire
10693 Prowatt SW 2000 Inverter
2000W
3000W
Hardwire
AC
Output
Dual
GFCI
Dual
GFCI
Dual
GFCI
USB
Output
Recommend
DC Fuse
Dimensions
H" x W" x L"
5V/500 mA
150A
3.5 x 8.7 x 12.2
6.5 lb.
2 Year
5V/500 mA
150A
3.5 x 8.7 x 13.4
7.2 lb.
2 Year
5V/500mA
150A
3.9 x 11.8 x 13.7 10.7 lb.
2 Year
Weight Warranty
Price†
Regulatory Compliance: UL458 – 5th Edition - Power Converters/Inverters and Power Converter/Inverter Systems for Land Vehicles and Marine Crafts.
www.xantrex.com
80
◆
Not UPS-able;
▲
Hazmat terms apply; LS Limited Supply
INVERTERS & ACCESSORIES
In Section D:
Meters/Testers
Wiring
™
Xantrex
Fuses
12V Accessories
Battery Accessories
D
ELECTRICAL
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
Advanced Charge Monitoring
Power Management Made Easy
Take the guesswork out of understanding your inverter/charger and battery
system. The LinkPro, LinkLite Battery Monitors & Freedom remote display let
you know how much power you have left and just how much longer it will take
to recharge. From one panel, you’ll have complete battery-state-of-charge
information for battery banks, and with just a touch of the keypad, you’ll be able
to independently control inverter and charger functions.
17980
17932
LinkLITE Battery
Monitor
LinkPRO Battery Monitor
Same great features of the LinkLite
plus the LinkPRO can measure
currents up to 10,000 Amps.
It selectively displays voltage,
charge and discharge current,
consumed amp hours, remaining
battery capacity and the time
remaining of your battery bank.
Battery Status At A Glance!
The LinkLITE battery monitor can
measure currents up to 1,000Amps.
It selectively displays voltage,
charge and discharge current,
consumed amp hours and
remaining battery capacity. It is
equipped with an internal programmable alarm relay, to run a generator when needed or to turn off
devices when the battery voltage
exceeds programmable boundaries.
Performance Features:
• Read your battery bank like a fuel
gauge. • Provides critical information about the status of your battery
bank. • Displays voltage, current,
consumed amp hours and remaining battery capacity. • Secondary
battery bank voltage monitoring.
• Auto sensing battery voltage
inputs. • Large backlit LCD Display.
• Quick nut mounting construction.
• Programmable alarm relay. • Shunt
selection capability enables flexible
system integration. • Splash proof
frontpanel. • 500 Amp shunt
included. • CE and e-mark certified.
• Displays time remaining. • Communication/expansion port. • Stores
a wide range of history events in
internal memory. * Advanced
programmable alarm relay. • Battery
temperature sensor input.
Order #
17932
17980
11807
11812
11807
Performance Features:
• Read your battery bank like a fuel
gauge. • Provides critical information about the status of your battery
bank. • Displays voltage, current,
consumed amp hours and
remaining battery capacity.
• Secondary battery bank voltage
monitoring. • Auto sensing battery
voltage inputs. • Large backlit
LCD Display. • Quick nut mounting
construction. • Programmable alarm
relay. • Shunt selection capability
enables flexible system integration.
• Splash proof frontpanel.
• 500 Amp shunt included.
• CE and e-mark certified.
11812
Freedom Basic Remote
Control
• Controls all 458 Freedom
RV inverter/charger units.
• Compatible with older black
Freedom units. • Easy to read
multi-colored LEDs.
Display Monitor Information.
• Approximate battery state.
• DC amps and voltage.
Push button control of:
• Power sharing. • Equalizing.
• Independent inverter and
charger on/off.
Freedom Echo Charge
• Automatically charges an
auxiliary or starter battery from
your inverter/charger. • Dual
battery bank charging for maintaining coach and engine battery
banks. • 15 A maximum charge
current. • Switches on/off without
affecting in-house battery bank or
overcharging.
LinkLite Battery Monitor
Controls
Freedom
Inverter/
Charger
Yes
LED
Yes
Yes
n/a
n/a
Yes
LS LinkPro Battery Monitor
Yes
LED
Yes
Yes
n/a
n/a
Yes
2.54 x 2.05 x 3.11 12 Mo.
Freedom Basic Remote
Yes
LED
Yes
Yes
No
No
n/a
5.75 x 3.75 x 1.0 12 Mo.
Description
Display
Type
DC Volt
Displayed
DC Amps
Display
Amp Hour
Consumed
Displayed
Time
Remaining
Diplay
Shunt
Dimensions
L" x W" x H"
2.54 x 2.05 x 3.11 12 Mo.
Warranty
Freedom Echo Charger #82-0123-01
www.xantrex.com
6
= Std. Carton Qty.
81
D
CONVERTERS/CHARGERS
ELECTRICAL
In Section D:
Meters/Testers
Wiring
Fuses
12V Accessories
Battery Accessories
Chargers & Inverters
Cords & Adapters
Box/Hatch
Switches
WFCO CONVERTERS, COME WITH
THE FOLLOWING FEATURES AND SAFETY PROTECTION:
Features: • 3 Stage battery charging system. • Two 30 amp fuse positions on 8900 fuse boards.
• 150 amp rated 8900 DC fuse boards. • LED fuse boards. • UL, cUL-Listed FCC Class B.
NEW!
Protection: • Reverse Polarity. • Over Temperature. • Short Circuit.
• Overload. • Over-current. • Current controlled fan.
Select WFCO products as your replacement converter of choice.
You can easily add a high performance converter to your RV. Take the guess
work out of choosing the right replacement converter by using the replacement
charts below. Dimensions are provided to assist with proper form and fit.
P O W E R
WF-8700 SERIES POWER CENTER
CONVERTER/CHARGER
AC/DC DISTIBUTION
C E N T E R S
WFCO
Mfr#
Description
Dimensions
Cut-out (W x H x D)
Progressive
Dynamics
Parallax
Atwood
Elixir
8712
8725
8735
8740
8935
8945
8955
8965
8975
12 Amp DC
25 Amp DC
35 Amp DC
40 Amp DC
35 Amp DC
45 Amp DC
55 Amp DC
65 Amp DC
75 Amp DC
10-7/16 x 6-1/8 x 3-3/4
10-7/16 x 6-1/8 x 3-3/4
10-7/16 x 6-7/8 x 3-3/4
10-7/16 x 6-7/8 x 3-3/4
12-3/16 x 10-7/8 x 7-1/4
12-3/16 x 10-7/8 x 7-1/4
12-3/16 x 10-7/8 x 7-1/4
12-3/16 x 10-7/8 x 7-1/4
12-3/16 x 10-7/8 x 7-1/4
PD4045
-
7335
7345
7355
-
APS5530
-
ELX12
ELX20/25
ELX35
ELX45
ELX60
-
D E C K M O U N T
WFCO
Mfr#
Description
Progressive
Dynamics
9835
35 Amp DC
4-5/8 x 4 x 7-1/2
9845
45 Amp DC
4-3/4 x 4 x 8-3/4
9855
55 Amp DC
4-3/4 x 4 x 8-3/4
9865
65 Amp DC
5-1/8 x 4 x 10-1/4
9875
75 Amp DC
5-1/8 x 4 x 10-1/4
68100
100 Amp DC
7-5/8 x 4 x 12-11/16
PD9130
PD9140/45A&
PD9245
PD9160A/
PD9260
PD9170A/
PD9270
PD9180A/
PD9280
M A I N
B O A R D
A S S E M B L Y
R E P L A C E M E N T
WFCO
Mfr#
Description
Parallax
8945REP
8955REP
8945MBA
8955MBA
45 Amp DC
55 Amp DC
45 Amp DC
55 Amp DC
7345
7355
7145
7155
NEW!
Replaces the lower power
converter section on any
WF-8900 Series converter. Installs
easily with only 4 screws and five wires.
15501
15516
15528
15733
15757
35Amp DC
45Amp DC
55Amp DC
65Amp DC
75Amp DC
Parallax Atwood
Iota
Elixir
7430
32
DSL-30
-
7445
45
DSL-45
-
7455
55
DSL-55
-
7465
-
-
DM6000
-
35414
DSL-75
DM8000
-
-
DSL-90
-
#WF-8935-MBA
#WF-8945-MBA
#WF-8955-MBA
#WF-8965-MBA
#WF-8975-MBA
1
1
1
1
1
CONVERTER/CHARGER, BLACK
15396 25A, Black #WF-8725-PB 1
15445 35A, Black #WF-8735-PB 1
CONVERTER/CHARGER, BROWN
15393 12A, Brown #WF-8712-P 1
15395 25A, Brown #WF-8725-P 1
15415 35A, Brown #WF-8735-P 1
16731 40A, Brown #WF-8740-P 1
NEW!
WF-9800 SERIES
DECK-MOUNT
CONVERTER/CHARGER
NEW!
The versatile, advanced power source solution.
Output ratings from 35 amps DC to 100 amps
DC. Convenient deck-mount installation.
WF-8900
SERIES
POWER
CENTER
CONVERTER/CHARGER
AC/DC DISTRIBUTION
WF-9800 SERIES
15761
15765
16843
15797
15824
The WF-8900 series converter provides superior
performance offering eleven 12 volt DC
circuits and up to five 110 volts AC circuits.
MAIN
BOARD
ASSEMBLIES
82
C O N V E R T E R S
Dimensions
(W x H x D)
Get big performance up to 40 amps DC output.
The WF-8700 series provide superior performance offering four to six 12 volt DC circuits
and three to five 110 volts AC branch circuits
(depending on the model).
CONVERTER/CHARGER, BLACK
15482 55A, Black #WF-8955-PECB
15497 65A, Black #WF-8965-ANPB
1
1
CONVERTER/CHARGER, BROWN
15458 35A, Brown #WF-8935-ANP 1
15462 45A, Brown #WF-8945-ANP 1
15481 55A, Brown #WF-8955-PEC 1
15496 65A, Brown #WF-8965-ANP 1
15499 75A, Brown #WF-8975-ANP 1
◆
35A
45A
55A
65A
75A
#WF-9835
#WF-9845
#WF-9855
#WF-9865
#WF-9875
1
1
1
1
1
UNIVERSAL
CONVERTER
REPLACEMENT
KIT
NEW!
8900REP models make
it easy to replace certain
brands of converters with
removable converter section.
15832 45A #WF-8945REP
15839 55A #WF-8955REP
Not UPS-able;
▲
1
1
Hazmat terms apply; LS Limited Supply
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement