59p2107
xSeries 205
Type 8480
Option Installation Guide
IBM xSeries 205
Type 8480
Option Installation Guide
IBM
Note:
Before using this information and the product it supports, be sure to read the general information in Appendix A, “Notices”
on page 37.
First Edition (August 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with
IBM Corp.
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notices and statements used in this book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Major components of the IBM Eserver xSeries 205 Type 8480 . . . . . . . . . . . . . . . . .
System and PCI extender boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System board internal cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System board external connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional system-management adapter component locations . . . . . . . . . . . . . . . .
1
1
2
3
4
5
5
Chapter 2. Installing internal options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System reliability considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Handling static-sensitive devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Moving the stabilizing feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing the side cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Removing the frame-support bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Working with adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adapter considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing a SCSI adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cabling a RAID adapter or single SCSI channel using one hot-swap drive SCSI
backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing internal drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Internal drive bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Preinstallation steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power and signal cables for internal drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installing a drive in bay 1, 2, 3, or 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing a non-hot-swap hard disk drive in bay 5, 6, or 7 . . . . . . . . . . . . . . . . . . 21
Installing a hot-swap hard disk drive in bay 5, 6, or 7 . . . . . . . . . . . . . . . . . . . . . . 23
Installing memory modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Installing a security rope clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing the side cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Replacing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Chapter 3. Connecting external options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mouse connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gigabit Ethernet port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Gigabit Ethernet controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-performance Ethernet modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Universal Serial Bus (USB) connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Microphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional system-management adapter ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
32
32
32
32
33
33
33
34
34
34
35
35
35
35
36
Appendix A. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Edition notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
iii
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic emission notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Federal Communications Commission (FCC) statement . . . . . . . . . . . . . . . . . . .
Industry Canada Class B emission compliance statement . . . . . . . . . . . . . . . . .
Avis de conformité à la réglementation d’Industrie Canada . . . . . . . . . . . . . . . . .
European Union EMC Directive conformance statement. . . . . . . . . . . . . . . . . . .
Japanese Voluntary Control Council for Interference (VCCI) statement . . . . . . .
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
39
39
40
40
40
40
40
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
iv
Book Title
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
v
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
• Connect all power cords to a properly wired and grounded electrical
outlet.
• Connect to properly wired outlets any equipment that will be attached
to this product.
• When possible, use one hand only to connect or disconnect signal
cables.
• Never turn on any equipment when there is evidence of fire, water, or
structural damage.
• Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
• Connect and disconnect cables as described in the following table
when installing, moving, or opening covers on this product or
attached devices.
To Connect:
Turn everything OFF.
1.
2.
First, attach all cables to devices.
2.
First, remove power cords from outlet.
3.
Attach signal cables to connectors.
3.
Remove signal cables from connectors.
4.
Attach power cords to outlet.
4.
Remove all cables from devices.
5.
Turn device ON.
1.
vi
Book Title
To Disconnect:
Turn everything OFF.
Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode
if not properly used, handled, or disposed of.
Do not:
•
Throw or immerse into water
•
Heat to more than 100° C (212° F)
•
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
•
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A` Laser de Classe 1
Safety
vii
Statement 4:
≥ 18 kg (39.7 lb)
≥ 32 kg (70.5 lb)
≥ 55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
viii
Book Title
Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact a
service technician.
Safety
ix
x
Book Title
Chapter 1. Introduction
Your server supports many optional devices. This Option Installation Guide provides
information for installing, removing, and connecting the optional devices that your
server supports.
In addition to this Option Installation Guide, the following IBM Eserver xSeries 205
Type 8480 documentation is provided with your server:
•
Installation Guide
This printed publication contains setup and installation instructions.
•
Safety Book
This multilingual publication is provided in Portable Document Format (PDF) on
the IBM® xSeries Documentation CD. It contains translated versions of the
caution and danger statements that appear in the documentation for your server.
Each caution and danger statement has an assigned number, which you can use
to locate the corresponding statement in your native language.
•
User’s Guide
This publication is provided in PDF format on the IBM xSeries Documentation CD.
It contains general information about your server.
•
Hardware Maintenance Manual and Troubleshooting Guide
This publication is provided in PDF format on the IBM xSeries Documentation CD.
It contains information to help you solve problems yourself or provide helpful
information to a service technician.
Depending on your server model, additional publications might be included on the IBM
xSeries Documentation CD.
Notices and statements used in this book
The caution statements and the danger statements also appear in the multilingual
Safety Information book provided on the IBM xSeries Documentation CD. Each
statement is numbered for easy reference to the corresponding statement in the safety
book.
The notice and statement definitions are as follows:
•
Notes: These notices provide important tips, guidance, or advice.
•
Important: These notices provide important information or advice that might help
you avoid inconvenient or problem situations.
•
Attention: These notices indicate possible damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
•
Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure or situation.
1
Major components of the IBM Eserver xSeries 205 Type 8480
The following illustration shows the locations of major components in the IBM Eserver
xSeries 205 Type 8480 server.
Note: The illustrations in this document might look slightly different from your
hardware.
Microprocessor
Rear adapterretaining bracket
EMC shields
Memory modules
Filler
panels
PCI extender
board
Drive cage
Front adaptersupport bracket
Frame-support bracket
Cover
2
Book Title
System and PCI extender boards
This illustration identifies parts of the system board and PCI extender board.
Depending on installed options, your system board and PCI extender board might look
slightly different.
Microprocessor
and fan (U6)
DIMM 2
DIMM 1
AGP
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
Battery
Chapter 1. Introduction
3
System board internal cable connectors
The following illustration identifies system board connectors for internal cables.
Microprocessor fan
connector (CN3)
Front fan
connector (CN2)
Main power
SCSI LED
connector
Primary IDE
(PRI IDE)
Rear fan
(CN19)
Secondary IDE
(SEC IDE)
Password check
jumper (JP1)
Microprocessor
power
CMOS
clear jumper (JP3)
Diskette drive
Internal speaker
connector
Wake on LAN®
connector
Video
connector
Boot block
jumper (JP6)
4
Book Title
SCSI drive connector
System board external connectors
The following illustration identifies system board connectors for external cables.
Keyboard
Mouse
Serial ports
Parallel
USB ports
Ethernet
Audio
Optional system-management adapter component locations
The following illustration shows the connectors and LEDs for the optional systemmanagement adapter that you can install in PCI slot 1 on the system board.
Ethernet link status
LED (green)
Ethernet port
(RJ-45)
P-
P
Ethernet activity
LED (green)
Serial port
(COM)
ASM Interconnect port
(RJ-14)
Error LED
(amber)
P- P
Power LED
(green)
External power
supply connector
(not used)
Chapter 1. Introduction
5
6
Book Title
Chapter 2. Installing internal options
This section provides instructions for installing options in an IBM Eserver xSeries 205
Type 8480.
Installation guidelines
Before you begin to install options in your server, read the following information:
•
Read the handling guidelines in “Handling static-sensitive devices”, and read the
safety statements in "Safety" beginning on page v. These guidelines will help you
work safely with your server and options.
•
Make sure that you have an adequate number of properly grounded electrical
outlets for your server, monitor, and other options that you intend to install.
•
Back up all important data before you make changes to disk drives.
•
Have a small, flat-blade screwdriver available.
•
Before accessing the inside of the IBM Eserver xSeries 205 Type 8480 server,
rotate the two front stabilizing feet a quarter turn towards the server, so they do
not break. Before placing the server in an upright position, rotate the two front feet
a quarter turn outward from the server. See “Moving the stabilizing feet” on page
8.
•
For a list of supported options for your server, go to
http://www.ibm.com/pc/support/ on the World Wide Web.
System reliability considerations
To help ensure proper system cooling and system reliability, make sure that:
•
Each of the drive bays has a drive or a filler panel and electromagnetic
compatibility (EMC) shield installed.
•
There is adequate space around the server to allow the server cooling system to
work properly. Leave approximately 51 mm (2 in.) of open space around the front
and rear of the server. Do not place objects in front of the fans.
•
You have followed the instructions for cabling provided with optional adapters.
•
You have replaced a failed fan as soon as possible.
Handling static-sensitive devices
Attention: Static electricity can damage electronic devices, including your server. To
avoid damage, keep static-sensitive devices in their static protective package until you
are ready to install them.
To reduce the possibility of damage from electrostatic discharge, observe the following
precautions.
•
Limit your movement. Movement can cause static electricity to build up around
you.
•
Handle the device carefully, holding it by its edges or its frame.
•
Do not touch solder joints, pins, or exposed circuitry.
•
Do not leave the device where others can handle and, possibly, damage the
device.
•
While the device is still in its static-protective package, touch it to an unpainted
metal part of the server for at least two seconds. (This drains static electricity from
the package and from your body.)
7
•
Remove the device from its package and install it directly into your server without
setting the device down. If it is necessary to set the device down, place it in its
static-protective package. Do not place the device on your server cover or on a
metal table.
•
Take additional care when handling devices during cold weather. Heating reduces
indoor humidity and increases static electricity.
Moving the stabilizing feet
The four feet on the bottom of the server provide additional stability when the feet are
placed in the stabilizing position.
Complete the following steps to place the feet in the stabilizing position:
1. Place the server on its side.
2. Locate the release tab inside the foot; then, lift up on the tab.
Note: The following illustration shows the rear feet located on the bottom rear of
the server.
Release tab
Feet (unlocked position)
Release tab
3. Rotate the foot inward to the unlocked position; then, remove the foot from the
server.
8
Book Title
4. Align the post in the center of the foot with the hole on the bottom of the server
and place the foot between the guides as indicated.
Note: The following illustration shows the rear feet located on the bottom rear of
the server.
Guides
Feet (locked position)
Guides
5. Rotate the foot outward until the foot locks into place.
6. Complete steps through for each foot.
Attention: When you need to access the inside of the server to install options,
you might find it easier to lay the server on its side. If you do so, make sure the
feet are in the horizontal position (see the previous steps). Otherwise, the feet
might break off from the server because of the weight of the server.
Removing the side cover
Complete the following steps to remove the side cover of the server.
Note: To remove the side cover, you might find it easier to lay the server on its side. If
you do, move the stabilizing feet so that they do not break. See “Moving the
stabilizing feet” on page 8.
1. Review the information in “Installation guidelines” on page 7 and “Safety” on page
v.
2. Turn off the server and all attached devices.
3. Disconnect all external cables and power cords.
Chapter 2. Installing internal options
9
4. Pull the cover-release latch away from the server, and push the side cover toward
the rear of the server.
Cover-release
latch
Key lock
To replace the side cover, see “Replacing the side cover” on page 28.
Attention: For proper cooling and airflow, replace the side cover before turning on the
server. Operating the server with the side cover removed might damage server
components.
Removing the frame-support bracket
When working with some options, such as hard disk drives, adapters, and memory
modules, you must first remove the frame-support bracket to access the existing
option.
10
Book Title
Complete the following steps to remove the frame-support bracket:
1. Pull out on the rear end of the frame-support bracket approximately 150 mm (6
in.).
2. Pull the rear end of the frame-support bracket away from the server and place the
bracket aside.
To reinstall the frame-support bracket, reverse the previous steps.
Working with adapters
Your server comes with five 32-bit, 33 MHz PCI adapter connectors or slots and one
AGP slot. You can install an AGP video adapter in the AGP slot.
See “System and PCI extender boards” on page 3 for the location of PCI expansion
slots on the system board and PCI extender board.
Adapter considerations
Before you install adapters, review the following:
•
Follow the instructions that come with the adapter in addition to the instructions in
this chapter. If you need to change the switch or jumper settings on your adapter,
follow the instructions that come with the adapter.
•
You can install full-length adapters in all five PCI slots.
•
Your server supports 5.0V and universal PCI adapters; it does not support 3.3V
adapters.
Chapter 2. Installing internal options
11
•
Your server uses a rotational interrupt technique to configure PCI adapters.
Therefore, you can install a variety of PCI adapters that currently do not support
sharing of PCI interrupts.
•
PCI slots 1 through 5 are on PCI bus 2.
The system scans the AGP slot and PCI expansion slots 1 through 5 to assign
system resources. Then, the system starts devices in the following order, if you
have not changed the default startup sequence: the AGP slot, PCI expansion
slots 1 and 2, system board integrated drive electronics (IDE) or SCSI devices,
and then PCI expansion slots 3 through 5.
•
The optional Remote Supervisor Adapter must be installed in PCI slot 1.
•
For a list of supported options for your server, go to
http://www.ibm.com/pc/support/ on the World Wide Web.
Installing an adapter
Complete the following steps to install an adapter.
Attention: When you handle static-sensitive devices, take precautions to avoid
damage from static electricity. For details about handling these devices, see “Handling
static-sensitive devices” on page 7.
1. Review the information in "Safety" beginning on page v.
2. Turn off the server and all attached devices, and disconnect all external cables
and power cords; then, remove the side cover. See “Removing the side cover” on
page 9.
Note: Check the instructions that come with the adapter for any requirements,
restrictions, or cabling instructions. It might be easier to route any cables
before you install the adapter.
3. Remove the frame-support bracket. See “Removing the frame-support bracket”
on page 10.
4. If you are installing a full-length adapter, rotate the front adapter-retaining bracket
to the open position.
5. Rotate the rear adapter-retaining bracket to the open (unlocked) position, and
remove it from the server.
6. From the rear of the server, press on the slot cover. Grasp it and pull the
expansion-slot cover out of the expansion slot. Store it in a safe place for future
use.
Attention: Expansion-slot covers must be installed on all vacant slots. This
maintains the electronic emissions standards of the server and ensures proper
ventilation of server components.
7. Set any jumpers or switches on the adapter or system board as described by the
adapter manufacturer.
12
Book Title
8. Remove the adapter from the static-protective package, carefully grasp the
adapter by the top edge or upper corners, and align it with the expansion slot
guides; then, press the adapter firmly into the expansion slot.
Note: It is best to move the adapter directly from the static-protective package to
the adapter slot. If this is not possible, set the adapter down on its staticprotective package on a hard surface. Avoid touching the components and
gold-edge connectors on the adapter.
Attention: Be certain that the adapter is correctly seated in the expansion slot
before you turn on the server. Incomplete installation of an adapter might damage
the system board or the adapter.
Expansion-slot
cover
Rear adapterretaining
bracket
Adapter
Front adaptersupport bracket
9. Connect required cables to the adapter. Route cables so that they do not block
airflow from the fans.
10. If you have another adapter to install, repeat steps 1 through 10. If you have
another option to install, do so now.
11. If you have installed a full-length adapter, rotate the front adapter-retaining bracket
to the closed (locked) position.
12. Reinstall the rear adapter-retaining bracket; then, rotate the bracket to the closed
(locked) position.
Note: The rear adapter-retaining bracket rests against the side cover. You might
find it easier to lay the server on its side to replace the side cover.
13. Replace the frame-support bracket.
14. Replace the side cover. See “Replacing the side cover” on page 28 for details.
15. Reconnect the external cables and power cords; then, turn on the attached
devices and the server.
Chapter 2. Installing internal options
13
Installing a SCSI adapter
Complete the following steps to install a SCSI adapter:
1. Complete steps through of “Installing an adapter” on page 12.
2. Connect the SCSI signal cable to the adapter and one or more of the signal cable
connectors to the rear of the SCSI devices.
3. Connect the SCSI activity indicator cable to the adapter and to the SCSI LED
connector on the system board. See “System and PCI extender boards” on page
3 for the location of the SCSI LED connector.
SCSI cable
RAID
adapter
SCSI connector
4. If you have other adapters or options to install or remove, do so now.
5. Rotate the front adapter-support bracket to the closed (locked) position.
6. Reinstall the rear adapter-support bracket; then, rotate it to the closed (locked)
position.
7. Replace the frame-support bracket.
8. Replace the side cover. See “Replacing the side cover” on page 28 for details.
9. Reconnect the external cables and power cords; then, turn on the attached
devices and the server.
Cabling a RAID adapter or single SCSI channel using one hot-swap drive
SCSI backplane
You can install an optional RAID adapter in your server to control the internal hot-swap
hard disk drives. The illustrations in this section show the cabling for internal hot-swap
hard disk drives. You can also cable a RAID adapter to external hard disk drives. See
your RAID adapter option documentation for complete instructions for installing a
RAID adapter in your server and for additional information about RAID adapters.
14
Book Title
One end of the SCSI cable is attached to the connector on the standard SCSI
backplane, and the other end is attached to the internal SCSI channel connector on
the PCI extender board or RAID adapter.
If you are connecting the server to more than two SCSI channels, you might need to
purchase additional SCSI cables. Consult your IBM marketing representative or
reseller for additional information about the number and types of cables that your
server configuration requires.
The following procedure describes the single-channel cable routing that is necessary
when you install a RAID adapter. The illustrations in this section are examples. The
cabling that you use for your server depends on your system configuration.
Notes:
1. See the documentation that comes with your adapter for any cabling instructions.
2. Cable identifiers are printed on the cables that come with your server and options.
Use these identifiers to connect the cables to the correct connectors. For example,
the hard disk drive cables are labeled “HDD option.”
Complete the following steps to cable a single SCSI channel on an installed RAID
adapter using the standard hot-swap drive SCSI backplane:
1. Determine the number of SCSI channels that you want to use on the RAID
adapter.
2. Review the information in “Installation guidelines” on page 7 and “Safety” on page
v.
3. Turn off the server and peripheral devices and disconnect all power cords and
external cables; then, remove the side cover (see “Removing the side cover” on
page 9).
4. If your server comes with a SCSI connector on the PCI extender board,
disconnect the SCSI cable from the internal SCSI connector on the PCI extender
board.
Attention: When you route the SCSI cable, observe these precautions:
•
Do not block the ventilated space in front of the fan assembly.
•
Do not route the SCSI cable over the memory board assembly.
Chapter 2. Installing internal options
15
5. Route the SCSI cable from the backplane on the hot-swap drive cage (bays 5 to 7)
to the internal channel connector on the RAID adapter.
SCSI cable
RAID
adapter
SCSI connector
6. If you have other options to install or remove, do so now; otherwise, go to
“Replacing the side cover” on page 28.
Installing internal drives
Depending on your server model, you might have one or more of the following drives
installed.
•
•
•
Diskette
Hard disk
CD-ROM or DVD-ROM
Internal drive bays
The IBM Eserver xSeries 205 Type 8480 server comes with an IDE CD-ROM or DVDROM drive in bay 1, a 3.5-in., 1.44 MB diskette drive in bay 3, and a hard disk drive
installed in bay 4.
16
Book Title
Bay 1
Bay 2
Bay 3
Bay 4
Bay 5
Bay 6
Bay 7
Before you install an internal drive, review the following information:
•
Diskette drives, tape drives, CD-ROM, and DVD-ROM drives are examples of
removable-media drives. You can install removable-media drives in bays 1, 2, 3,
and 4 only.
•
You can install a 3.5-in. slim-high, or a 5.25-in. half-high removable-media drive,
such as a tape backup drive, in bay 2.
•
You can install a 3.5-in. slim-high removable-media drive only in bay 4.
•
The IBM xSeries 205 Type 8480 server supports only one diskette drive.
•
To install a 3.5-in. drive in a 5.25-in. bay, you must use a 5.25 in. conversion kit,
supplied with your option.
Note: Only 3.5-in. options that come with proper mounting hardware are
supported in the 5.25-in. bays.
•
The electromagnetic interference (EMI) integrity and cooling of the server are
protected by having all bays and PCI slots covered or occupied. When you install
a drive or PCI adapter, save the EMC shield and filler panel from the bay or the
PCI adapter slot cover in the event you later remove the option.
•
For a complete list of supported options for your server, go to
http://www.ibm.com/pc/support/ on the World Wide Web.
Preinstallation steps
Before you install drives in your server, verify that you have all the cables and other
equipment specified in the documentation that comes with the drive. You might also
need to perform certain preinstallation activities. Some of the steps are required only
during the initial installation of an option.
Chapter 2. Installing internal options
17
Before installing a drive in bays 1, 2, 3, or 4, do the following:
1. Read "Safety" beginning on page v, “Handling static-sensitive devices” on page 7,
and the documentation that comes with your drive.
2. Choose the bay in which you want to install the drive.
3. Check the instructions that come with the drive to see if you need to set any
switches or jumpers on the drive. If you are installing a SCSI device, be sure to set
the SCSI ID for that device.
Power and signal cables for internal drives
Your server uses cables to connect IDE and SCSI devices to the power supply and to
the system board. The following cables are provided:
•
Four-wire power cables connect the drives to the power supply. At the end of
these cables are plastic connectors of various sizes that can be attached to
different drives.
•
Flat signal cables, also called ribbon cables, connect IDE, SCSI, and diskette
drives to the system board. Two or three sizes of ribbon cables come with your
server:
— The wider IDE signal cable has two or three connectors.
–
If the cable has three connectors, one of these connectors is attached to
the drive, one is a spare, and the third is attached to the primary or
secondary IDE connector on the system board.
–
If the cable has two connectors, one of these connectors is attached to
the hard disk drive, and the other is attached to the primary or secondary
IDE connector on the system board.
Note: The CD-ROM drive is attached to an ATA 66 signal cable. The hard
disk drive is attached to an ATA 100 signal cable. ATA 66 and ATA 100
signal cables are color-coded. The blue connector attaches to the
system board. The black connector attaches to the primary device. If
the cable has a gray middle connector, it attaches to the secondary
device. If you are installing a hard disk drive, you must change the
switch setting on the CD-ROM drive to secondary and change the
connector used for the CD-ROM drive to the gray middle connector.
— The narrower signal cable has two connectors, one to attach to the diskette
drive, and the other to attach to the connector (FDD1) on the system board.
— If your server comes with a SCSI connector on the extender board and SCSI
hard disk drive, an Ultra160 twisted ribbon cable connects the internal
Ultra160 SCSI hard disk drive to the SCSI connector on the PCI extender
board. This cable has two additional connectors for attaching more internal
SCSI devices.
To locate connectors on the system board, see “System board internal cable
connectors” on page 4.
Review the following information before connecting power and signal cables to internal
drives:
18
Book Title
•
The drives that are preinstalled in your server come with power and signal cables
attached. If you replace any drives, remember which cable is attached to which
drive.
•
When you install a drive, ensure that the drive connector at one end of the signal
cable is connected to the drive and that the drive connector at the other end is
connected to the system board.
•
If you have only one IDE device on a cable, it must be set as a primary device.
•
If two IDE devices are used on a single cable, one must be designated as the
primary device and the other as the secondary device; otherwise, the server might
not recognize some of the IDE devices. The primary and secondary designation
is determined by switch or jumper settings on each IDE device.
•
If two IDE devices are on a single cable and only one is a hard disk drive, the hard
disk drive must be set as a primary device.
•
You must also set the SCSI ID for any SCSI device that you install in your server.
Each SCSI device has its own methods and considerations for setting the SCSI
ID. See the instructions that come with the SCSI device for details about setting
the SCSI ID for the SCSI device.
Installing a drive in bay 1, 2, 3, or 4
Do the following to install a drive in bay 1, 2, 3, or 4:
Attention: When handling static-sensitive devices, take precautions to avoid damage
from static electricity. For details on handling these devices, see “Handling staticsensitive devices” on page 7.
1. Read the information in “Preinstallation steps” on page 17.
2. Turn off the server and attached devices and disconnect the external cables and
power cords.
3. Remove the side cover. See “Removing the side cover” on page 9 for details.
4. Remove the frame-support bracket. See “Removing the frame-support bracket”
on page 10.
5. Use a screwdriver to pry the filler panel and EMC shield away from the server.
Note: If you are installing a drive that contains a laser, observe the following
safety precaution.
Chapter 2. Installing internal options
19
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
•
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the
beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A` Laser de Classe 1
6. Touch the static-protective package containing the drive to any unpainted metal
surface on the server; then, remove the drive from the package and place it on a
static-protective surface.
7. Set any jumpers or switches on the drive according to the documentation that
comes with the drive.
8. You might find it easier to install the new drive into the appropriate opening on the
front, and then attach the cables.
9. If you are installing a 5.25-in. drive in bay 2, push the drive into the bay; then, use
the two screws to attach the drive to the drive cage.
20
Book Title
10. If you are installing a 3.5-in. drive in bay 2, you must attach the 5.25-in conversion
kit, supplied with your option, to the 3.5-in. drive.
Note: You can install only a 3.5-in. device in bay 4.
EMC shield
Filler panel
11. If the drive is an IDE device, connect one end of the IDE signal cable into the back
of the drive and the other end of the cable into the IDE connector on the system
board. For the location of the IDE connectors, see “System board internal cable
connectors” on page 4. If the drive is a SCSI device, connect one end of the SCSI
signal cable into the back of the drive and the other end of the cable into the 68pin connector on the PCI connector on the extender board.
Note: Route the signal cable so that it does not block the airflow to the rear of the
drives or over the microprocessor.
12. Connect the power cable to the back of the drive. The connectors are keyed and
can be inserted only one way.
13. If you have other options to install or remove, do so now.
14. Replace the frame-support bracket.
15. Replace the side cover. See “Replacing the side cover” on page 28 for details.
16. Reconnect the external cables and power cords; then turn on the attached
devices and the server.
Installing a non-hot-swap hard disk drive in bay 5, 6, or 7
Bays 5, 6, and 7 are in the drive cage. The drive cage is located just above the front
adapter-support bracket.
Note: You might find it useful to work with the server laying on its side.
Chapter 2. Installing internal options
21
Complete the following steps to install a non-hot-swap hard disk drive in bay 5, 6, or 7:
1. Review the safety precautions listed in "Safety" beginning on page v.
2. Read the information in “Preinstallation steps” on page 17.
3. Turn off the server and all attached devices. Disconnect all external cables and
power cords; then remove the side cover. See “Removing the side cover” on page
9 for details.
4. Remove the frame-support bracket and disconnect the fan cable from the
connector on the system board. See “Removing the frame-support bracket” on
page 10 for details.
5. If your server has hard disk drives preinstalled in the drive cage, disconnect the
power and signal cables from the rear of the drives.
6. Rotate the drive cage out of the server until it locks into place with the drive-cageretention tab. The open ends of the drive slots and installed drives will face you.
Note: Ensure that the drive cage locks into place over the drive-cage-retention
tab by pressing the drive cage all the way up.
7. Attach the guide rails to the side of the drive using the screws provided. If you
obtained your optional drive from IBM, the guide rails are blue plastic.
8. Slide the drive into the drive cage until the plastic tabs on the drive guide rails lock
into place in the drive cage. Clear any cables that might impede the replacement
of the drive cage.
9. Press in on the drive-cage-retention tab, and rotate the cage back into the server.
Drive “cage”
retention tab
10. Connect the power and signal cables to the rear of each drive.
Note: Route the signal cable so that it does not block the airflow to the rear of the
drives or over the microprocessor.
11. If you have other options to install or remove, do so now.
22
Book Title
12. Replace the frame-support bracket.
13. Replace the side cover. See “Replacing the side cover” on page 28 for details.
14. Reconnect the external cables and power cords; then, turn on the attached
devices and the server.
Installing a hot-swap hard disk drive in bay 5, 6, or 7
If your server is a hot-swap model, you can replace a failed hard disk drive without
turning off the server. Therefore, you can continue to operate your server while a hard
disk drive is removed or installed. To do this, you must install a hot-swap hard disk
drive. If a hot-swap disk drive is connected to an optional hot-swap RAID controller
and if your hot-swap drive becomes defective, the RAID controller can rebuild the data
from that drive onto another hot-swap drive. See the information that comes with your
RAID controller for details.
Each hot-swap drive has a green hard disk drive activity LED and an amber hard disk
drive status LED. When the hard disk drive activity LED is flashing, the controller is
accessing the hard disk drive. When this occurs, the SCSI activity LED on the front of
the server is also lit. The hard disk drive activity LED is illustrated and described in the
User’s Guide. If the hard disk drive status LED for a drive is lit continuously, that
individual drive is faulty and requires replacement. When the hard disk drive status
LED indicates a drive fault, you can replace a hot-swap drive without turning off the
server.
Each hot-swap drive that you plan to install comes mounted in a hot-swap-drive tray.
The drive must have a single connector attachment (SCA) connector. Hot-swap-drive
trays come with hot-swap drives.
The hot-swap bays are connected to a SCSI backplane. This backplane is the printed
circuit board behind the bay. The backplane controls the SCSI IDs for the hot-swap
drives.
The following illustration shows the hot-swap-drive backplane component locations, as
viewed from the front of the server.
Hard disk
drive activity
LED (green)
Hard disk
drive status
LED (amber)
SCSI hot-swap
hard disk drive
connector
Note: The hard disk drive activity LED and hard disk drive status LED on the
backplane match the hard disk drive activity LED and hard disk drive status
LED on the hot-swap drive.
Chapter 2. Installing internal options
23
The following illustration shows the rear connectors on the hot-swap-drive backplane,
as viewed from the rear of the server.
SCSI cable
connector
SCSI power
cable connector
2
I C cable
connector
When you install hot-swap hard disk drives, install them in the following order: bay 7,
bay 6, and bay 5.
Attention:
•
When you handle static-sensitive devices, take precautions to avoid damage from
static electricity. For details on handling these devices, see “Handling staticsensitive devices” on page 7.
•
To maintain proper system cooling, do not operate the server for more than 10
minutes without either a drive or a filler panel installed in each bay.
Complete the following steps to install a hot-swap hard disk drive in bay 5, 6, or 7.
Note: You do not have to turn off the server to install hot-swap hard disk drives in
these bays.
1. Read the information in “Preinstallation steps” on page 17.
2. Remove the filler panel from one of the empty hot-swap bays by inserting your
finger into the depression at the left side of the filler panel and pulling it away from
the server.
24
Book Title
3. Install the hard disk in the hot-swap bay:
a. Ensure that the tray handle is open (that is, perpendicular to the drive).
b.
Align the drive-tray assembly with the guide rails in the bay.
c.
Gently push the drive-tray assembly into the bay until the drive stops.
d. Push the tray handle to the closed (locked) position.
Filler panel
Drive tray
assembly
Drive tray handle
(in open position)
e. Check the hard disk drive status LED to verify that the hard disk drive is
operating properly.
If the amber disk drive status LED for the drive is lit continuously, that
individual drive is faulty and needs to be replaced. If the green hard disk drive
activity LED is flashing, the drive is being accessed.
Note: If your server has a RAID adapter, you might need to reconfigure your disk
arrays after installing hard disk drives. See the information that comes
with your RAID adapter.
4. If you have other options to install or remove, do so now.
Installing memory modules
You can increase the amount of memory in your server by installing memory modules.
Your IBM xSeries 205 Type 8480 server uses industry-standard dual inline memory
modules (DIMMs).
Complete the following steps to install a DIMM:
Attention: When handling static-sensitive devices, take precautions to avoid
damage from static electricity. For details on handling these devices, see “Handling
static-sensitive devices” on page 7.
1. Review the safety precautions listed in the "Safety" beginning on page v.
2. Turn off the server and all attached devices. Disconnect all external cables and
power cords; then remove the side cover. See “Removing the side cover” on page
9 for details.
3. Remove the frame-support bracket. See “Removing the frame-support bracket”
on page 10.
Chapter 2. Installing internal options
25
4. Touch the static-protective package containing the DIMM to any unpainted metal
surface on the server. Then remove the new DIMM from the package.
5. Open the retaining clips and, if necessary, remove any existing DIMM.
6. Turn the DIMM so that the pins align correctly with the connector, and firmly press
the DIMM straight down into the connector by applying pressure on both ends of
the DIMM simultaneously. The retaining clips snap into the locked position when
the DIMM is firmly seated in the connector.
DIMM connector 1
DIMM connector 2
7. If there is a gap between the DIMM and the retaining clips, the DIMM has not
been correctly installed. Open the retaining clips, remove the DIMM, then reinsert
it.
8. If you have other options to install or remove, do so now.
9. Replace the frame-support bracket.
10. Replace the side cover. See “Replacing the side cover” on page 28.
11. Reconnect the external cables and power cords. Turn on the attached devices,
and turn on the server.
Installing a security rope clip
To help prevent theft, you can add a security rope clip and cable to your server.
Complete the following steps to install the rope clip:
1. Review the safety precautions listed in "Safety" beginning on page v.
2. Turn off the server and all attached devices. Disconnect all external cables and
power cords; then, remove the side cover. See “Removing the side cover” on
page 9 for details.
26
Book Title
3. Use a screwdriver to remove the two metal knockouts.
4. Insert the rope clip through the rear panel; then attach and tighten the nuts.
5. Thread the cable through the rope clip and around an object that is not part of or
permanently secured to the building structure or foundation and from which the
cable cannot be removed. Fasten the cable ends together with a lock. After you
add the security cable, be certain it does not interfere with other cables connected
to the server.
Rope clip
6. Reconnect the external cables and power cords, and turn on the attached
devices, and then the server.
Chapter 2. Installing internal options
27
Replacing the side cover
Complete the following steps to replace the side cover of the server.
Note: If you removed the frame-support bracket, reinstall it before you replace the
side cover. See “Removing the frame-support bracket” on page 10 for details.
1. Clear any cables that might impede the replacement of the side cover.
2. Install the side cover by placing it into position on the server. Be certain the
notches on the underside of the side cover match up to the holes along the sides
of the server. Press down on the cover-release latch button as you close the
cover-release latch to lock the side cover.
Cover-release
latch
Key lock
3. If you have not done so already, make sure that the two front stabilizing feet are
rotated outward so that they properly support the server. Rotate each individual
foot outward 90 degrees.
4. Reconnect the external cables and power cords to the server; then, connect the
power cords to electrical outlets.
5. Turn on the attached devices; then, turn on the server.
Replacing the battery
When replacing the battery, you must replace it with a lithium battery of the same type
from the same manufacturer. To avoid possible danger, read and follow the information
in “Safety” on page v.
28
Book Title
To order replacement batteries, call 1-800-772-2227 within the United States, and 1800-465-7999 or 1-800-465-6666 within Canada. Outside the U.S. and Canada, call
your IBM reseller or IBM marketing representative.
Note: After you replace the battery, you must reconfigure your server and reset the
system date and time.
Complete the following steps to replace the battery:
1. Follow any special handling and installation instructions supplied with the
replacement battery.
2. Turn off the server and all attached devices. Disconnect all external cables and
power cords; then, remove the side cover and frame-support bracket. See
“Removing the side cover” on page 9 and “Removing the frame-support bracket”
on page 10.
3. Complete the following steps to remove the battery:
a. Use one fingernail to press the top of the battery clip away from the battery.
The battery pops up when released.
b.
Use your thumb and index finger to lift the battery from the socket.
4. Complete the following steps to insert the new battery:
a. Tilt the battery so that you can insert it into the socket on the side opposite the
battery clip.
b.
Press the battery down into the socket until it clicks into place. Make sure the
battery clip holds the battery securely.
5. Replace the frame-support bracket and the side cover and connect the cables.
See “Replacing the side cover” on page 28.
6. Turn on the server.
7. Start the Configuration/Setup Utility program and set configuration parameters.
•
Set the system date and time.
•
Set passwords if necessary.
•
Save the configuration.
Chapter 2. Installing internal options
29
30
Book Title
Chapter 3. Connecting external options
You can connect a number of optional external devices to the connectors on the rear
of the server, such as a printer, a keyboard, or a mouse.
Power cord
Mouse
Keyboard
Parallel
Serial 1
Serial 2
USB 1
1
USB 2
2
2
1
Ethernet
Line out (green)
Line in (blue)
Mic (pink)
Video
To attach an external device:
1. Read “Installation guidelines” on page 7, review the safety precautions listed in
Statement 1 and Statement 5 in “Safety” on page v, and read the documentation
that comes with your options.
2. Be sure that your server and all attached devices are turned off.
3. Follow the instructions that come with the option to prepare it for installation and to
connect it to the server.
This section provides information about the input/output connectors on the rear of your
server. These connectors are:
•
•
•
•
•
•
•
•
•
•
One mouse
One keyboard
One parallel
Two serial
One Ethernet
Two USB
Line in
Line out
Microphone
One video (Optional multiple connectors on some models)
31
Video connector
Your server uses a graphics controller located on the PCI extender card. The video
connector is located on the rear of your server. See the illustration on page 31 for the
location of this connector.
5
1
15
11
Some models come with a digital video interface (DVI) connector for connecting a
digital monitor.
C1
1
C2
C3
C4
C5
Keyboard connector
Your server has one keyboard connector. See the illustration on page 31 for its
location.
Note: If you attach a standard (non-USB) keyboard to the keyboard connector, the
USB ports and devices are disabled during the power-on self-test (POST).
6
5
4
3
2
1
Mouse connector
Your server has one mouse connector that supports a mouse or other pointing device.
The mouse connector is located on the rear of your computer. For the location, see
the illustration on page 31.
6
5
4
3
2
1
Parallel connector
Your server has one 25-pin, female D-shell parallel connector. This connector
supports three standard Institute of Electrical and Electronics Engineers (IEEE) 1284
modes of operation: standard parallel port (SPP), enhanced parallel port (EPP), and
extended capability port (ECP). See the illustration on page 31 for the location of this
connector.
32
Book Title
1
13
25
14
Use the Configuration/Setup Utility program to configure the parallel connector as
bidirectional. With this configuration, data can be read from and written to a device. In
bidirectional mode, the server supports the ECP and EPP modes.
For instructions to view or change the parallel-connector assignment, see the User’s
Guide on the IBM Documentation CD.
Serial connectors
Your server has two standard 9-pin D-shell serial connectors: Serial connector 1 and
Serial connector 2. See page 31 for their location.
5
1
6
9
Gigabit Ethernet port
Your server comes with an integrated Gigabit Ethernet controller. This controller
provides an interface for connecting to 10-Mbps, 100-Mbps, or 1000-Mbps networks
and provides full-duplex (FDX) capability, which enables simultaneous transmission
and reception of data on the Ethernet local area network (LAN).
Link LED
(green)
Activity LED
(green)
8
1
To access the Ethernet port, connect a Category 3, 4, or 5 unshielded twisted-pair
(UTP) cable to the RJ-45 connector on the rear of your server.
Note: The 100BASE-TX/1000BASE-T Fast Ethernet standard requires that the
cabling in the network be Category 5 or higher.
The Ethernet (RJ-45) connector has two LEDs. The Ethernet-link status LED is on the
left. When this green light is on, there is an active connection on the Ethernet port.
The Ethernet transmit/receive activity LED is on the right. When this amber LED is on,
there is activity between the server and the network. These LEDs have the same
functions as the Ethernet-link status LED and the Ethernet transmit/receive activity
LED on the rear of the server (see the User’s Guide).
Configuring the Gigabit Ethernet controller
The Ethernet controller is a PCI Plug and Play device. You do not need to set any
jumpers or configure the controller for your operating system before you use the
Ethernet controller. However, you must install a device driver to enable your operating
Chapter 3. Connecting external options
33
system to address the Ethernet controller. The device drivers are provided on the
Device Drivers and IBM Enhanced Diagnostics CD.
When you connect your server to the network, the Ethernet controller automatically
detects the data-transfer rate (10 Mbps, 100 Mbps, or 1000 Mbps) on the network and
then sets the controller to operate at the appropriate rate. In addition, if the Ethernet
ports that your server is connected to support auto-negotiation, the Gigabit Ethernet
controller will set the appropriate duplex state. That is, the Ethernet controller will
adjust to the network data rate, whether the data rate is standard Ethernet (10BASET), Fast Ethernet (100BASE-TX/1000BASE-T), half duplex (HDX), or full duplex
(FDX). The controller supports half-duplex (HDX) and full-duplex (FDX) modes at both
speeds.
High-performance Ethernet modes
Your Ethernet controller supports optional modes, such as teaming, load balancing,
fault tolerance, and virtual LANs, which provide higher performance, security, and
throughput for your server. These modes apply to the integrated Ethernet controller
and to the controllers on supported Ethernet adapters.
Universal Serial Bus (USB) connectors
Your server has two Universal Serial Bus (USB) 2.0 connectors for optional telephony
and multimedia devices. USB 2.0 devices configure automatically with Plug and Play
technology. See the illustration on page 31 for the location of the USB 2.0 connectors.
1
4
Notes:
1. If you attach a standard (non-USB) keyboard to the keyboard connector, the USB
2.0 connectors and devices will be disabled during the power-on self-test.
2. If you install a USB keyboard that has a mouse connector, the USB keyboard
emulates a mouse, and you will not be able to disable the mouse settings in the
Configuration/Setup Utility program.
USB cables
Use a 4-pin USB cable to connect external devices to USB connectors.
USB 2.0 technology transfers data at up to 128 megabits per second (Mbps) with a
maximum of 127 external devices and a maximum signal distance of 5 meters (16 ft)
per segment. You must use devices that support USB 2.0 in order to obtain this
maximized data transfer rate.
34
Book Title
Audio connectors
The audio connectors are used to connect external audio equipment to your server.
See the illustration on page 31 for the location of these connectors.
Mic (pink)
Line in (blue)
Line out (green)
Line out
This connector is used to send audio signals from the server to external devices, such
as powered speakers with built-in amplifiers, headphones, multimedia keyboards, or
the audio Line in connector on a stereo system.
Note: The internal speaker in your server is disabled when any device is attached to
this connector.
Line in
This connector is used to accept audio signals from external devices, such as line
output from external audio equipment into the server sound system.
Microphone
This connector is used to connect a microphone to your server when you want to
record sounds on the hard-disk drive or use speech recognition software.
Chapter 3. Connecting external options
35
Optional system-management adapter ports
The following illustration shows the connectors and LEDs for the Remote Supervisor
Adapter (optional system-management adapter). See the Remote Supervisor Adapter
option documentation for detailed information about the advanced system
management (ASM) interconnect network.
Ethernet link status
light (green)
Ethernet port
(RJ-45)
Ethernet activity
light (green)
Serial port
(COM)
ASM Interconnect port
(RJ-14)
Error light
(amber)
External power
supply connector
(not used)
36
Book Title
P- P
Power light
(green)
P-
P
Appendix A. Notices
This publication was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the products
and services currently available in your area. Any reference to an IBM product,
program, or service is not intended to state or imply that only that IBM product,
program, or service may be used. Any functionally equivalent product, program, or
service that does not infringe any IBM intellectual property right may be used instead.
However, it is the user’s responsibility to evaluate and verify the operation of any nonIBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Any references in this publication to non-IBM Web sites are provided for convenience
only and do not in any manner serve as an endorsement of those Web sites. The
materials at those Web sites are not part of the materials for this IBM product, and use
of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
Edition notice
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION, 2002.
All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use,
duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule
Contract with IBM Corp.
37
Trademarks
The following terms are trademarks of International Business Machines Corporation in
the United States, other countries, or both:
Active PCI
ServerGuide
Alert on LAN
ServerProven
e-business logo
Update Connector
IBM
Wake on LAN
Predictive Failure Analysis
X-Architecture
PS/2
xSeries
ServeRAID
Lotus, Lotus Notes, SmartSuite, and Domino are trademarks of Lotus Development
Corporation and/or IBM Corporation in the United States, other countries, or both.
Intel, Celeron, LANDesk, MMX, NetBurst, Pentium, Pentium II Xeon, Pentium III Xeon,
and Xeon are trademarks of Intel Corporation in the United States, other countries, or
both.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in the
United States, other countries, or both.
UNIX is a registered trademark of The Open Group in the United States and other
countries.
Java and all Java-based trademarks and logos are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States, other countries, or both.
Linux is a registered trademark of Linus Torvalds.
Other company, product, or service names may be trademarks or service marks of
others.
Important notes
Processor speeds indicate the internal clock speed of the microprocessor; other
factors also affect application performance.
CD-ROM drive speeds list the variable read rate. Actual speeds vary and are often
less than the maximum possible.
When referring to processor storage, real and virtual storage, or channel volume, KB
stands for approximately 1000 bytes, MB stands for approximately 1 000 000 bytes,
and GB stands for approximately 1 000 000 000 bytes.
When referring to hard disk drive capacity or communications volume, MB stands for
1000000 bytes, and GB stands for 1000 000 000 bytes. Total user-accessible
capacity may vary depending on operating environments.
38
Book Title
Maximum internal hard disk drive capacities assume the replacement of any standard
hard disk drives and population of all hard disk drive bays with the largest currently
supported drives available from IBM.
Maximum memory may require replacement of the standard memory with an optional
memory module.
IBM makes no representation or warranties regarding non-IBM products and services
that are ServerProven, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose. These products are offered and
warranted solely by third parties.
IBM makes no representations or warranties with respect to non-IBM products.
Support (if any) for the non-IBM products is provided by the third party, not IBM.
Some software may differ from its retail version (if available), and may not include user
manuals or all program functionality.
Electronic emission notices
IBM Eserver xSeries 205 Type 8480
Federal Communications Commission (FCC) statement
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult an IBM authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order to meet
FCC emission limits. Proper cables and connectors are available from IBM authorized
dealers. IBM is not responsible for any radio or television interference caused by using
other than recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Responsible party:
International Business Machines Corporation
New Orchard Road
Armonk, NY 10504
Appendix A. Notices
39
Telephone: 1-919-543-2193
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Industry Canada Class B emission compliance statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council Directive
89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility. IBM cannot accept responsibility for any failure to
satisfy the protection requirements resulting from a nonrecommended modification of
the product, including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class B equipment were derived for typical residential
environments to provide reasonable protection against interference with licensed
communication devices.
Japanese Voluntary Control Council for Interference (VCCI) statement
Power cords
For your safety, IBM provides a power cord with a grounded attachment plug to use
with this IBM product. To avoid electrical shock, always use the power cord and plug
with a properly grounded outlet.
IBM power cords used in the United States and Canada are listed by Underwriter's
Laboratories (UL) and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified cord
set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a
maximum of 15 feet in length and a parallel blade, grounding-type attachment plug
rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSAcertified cord set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor
cord, a maximum of 15 feet in length and a tandem blade, grounding-type attachment
plug rated 15 amperes, 250 volts.
40
Book Title
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a
grounding-type attachment plug. The cord set should have the appropriate safety
approvals for the country in which the equipment will be installed.
IBM power cords for a specific country or region are usually available only in that
country or region.
IBM power cord part
number
Used in these countries and regions
13F9940
Argentina, Australia, China (PRC), New Zealand, Papua New
Guinea, Paraguay, Uruguay, Western Samoa
13F9979
Afghanistan, Algeria, Andorra, Angola, Austria, Belgium, Benin,
Bulgaria, Burkina Faso, Burundi, Cameroon, Central African Rep.,
Chad, China (Macau S.A.R.), Czech Republic, Egypt, Finland,
France, French Guiana, Germany, Greece, Guinea, Hungary,
Iceland, Indonesia, Iran, Ivory Coast, Jordan, Lebanon,
Luxembourg, Malagasy, Mali, Martinique, Mauritania, Mauritius,
Monaco, Morocco, Mozambique, Netherlands, New Caledonia,
Niger, Norway, Poland, Portugal, Romania, Senegal, Slovakia,
Spain, Sudan, Sweden, Syria, Togo, Tunisia, Turkey, former USSR,
Vietnam, former Yugoslavia, Zaire, Zimbabwe
13F9997
Denmark
14F0015
Bangladesh, Burma, Pakistan, South Africa, Sri Lanka
14F0033
Antigua, Bahrain, Brunei, Channel Islands, China (Hong Kong
S.A.R.), Cyprus, Dubai, Fiji, Ghana, India, Iraq, Ireland, Kenya,
Kuwait, Malawi, Malaysia, Malta, Nepal, Nigeria, Polynesia, Qatar,
Sierra Leone, Singapore, Tanzania, Uganda, United Kingdom,
Yemen, Zambia
14F0051
Liechtenstein, Switzerland
14F0069
Chile, Ethiopia, Italy, Libya, Somalia
14F0087
Israel
1838574
Thailand
6952301
Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman
Islands, Colombia, Costa Rica, Dominican Republic, Ecuador, El
Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan,
Korea (South), Liberia, Mexico, Netherlands Antilles, Nicaragua,
Panama, Peru, Philippines, Saudi Arabia, Suriname, Taiwan,
Trinidad (West Indies), United States of America, Venezuela
Appendix A. Notices
41
42
Book Title
Index
A
adapter
considerations 11
full length 11
installing 12
PCI bus 12
system management 36
audio connectors 35
B
battery replacement 28
bay
1, 2, 3, and 4 19
5, 6, and 7 21
drive 16
filler panel 19
bi-directional parallel port configuration 33
C
cable
external 5
cables
internal drives 18
power 18
power and signal 18
signal 18
universal serial bus (USB) 34
cabling
RAID adapter 14
SCSI channel 15
SCSI device 21, 22
CD-ROM drive
installing 14
components
hardware 2
location of 2
major 2
connecting external options 31
connector
audio 35
DVI-I monitor 32
Ethernet 33
input/output (I/O) 32
keyboard 32
mouse 32
parallel 32
serial 33
universal serial bus (USB) 34
video 32
connectors
external 5
cooling 7
cover
removing 9
replacing 28
D
DIMM
connector locations 25
installing memory 25
retaining clips 26
diskette drive
installing 14, 19, 21
drive
bay filler panel 19
installation 19, 21
installing 14
preinstallation 17
E
Ethernet
Gigabit controller 33
high performance modes 34
modes 34
port 33
teaming 34
Ethernet controller
configuring 34
Ethernet port 33
expansion bays
location 16
type 16
F
Fast Ethernet 34
filler panel 19
H
handling static-sensitive devices 7
hard disk drive, installing 14
hardware, major components 2
hubs, USB 34
I
input/output (I/O)
connectors 31
ports 31
installing
adapters 12
battery 28
drive in bays 1, 2, 3, or 4 19
43
drives in bays 5, 6, or 7 21
hot-swap hard disk drives 23
internal drives 14
memory modules 25
non-hot-swap hard disk drives 21
options 7
security U-bolt 26
installing drives
bays 5, 6, and 7 21
internal
cable connectors 4
drive bays 16
drives, installing 14
K
keyboard, connector 32
M
memory
DIMM 25
installing 25
modules 25
modes, Ethernet 34
mouse, connector 32
N
notes, important 38
notices
attention 1
caution 1
important 1
P
S
security U-bolt 26
serial connectors 33
side cover, removing 9
small computer systems interface (SCSI)
adapter 14
device 21
stabilizing feet 8
statements
attention 1
caution 1
important 1
static-sensitive devices, handling 7
support-bracket assembly, removing 10
system board
connectors 4
options 3
system management
adapter 5
system reliability 7
T
tape drive, installing 14
trademarks 38
U
parallel port
bi-directional configuration 33
connector 32
connector pin-assignments 32
PCI
expansion slots 11
pin-assignments
video 32
port
Ethernet 33
keyboard 32
mouse 32
parallel 32
universal serial bus (USB) 34
power cords 40
R
RAID adapter 14
44
reliability, system 7
removable media drives, installing 14
removing
side cover 9
support-bracket assembly 10
replacing
battery 28
side cover 28
retaining clips, DIMM 26
Book Title
universal serial bus (USB)
cables 34
connectors 34
ports 34
V
video
connector 32
DVI-I connector 32
IBM
Part Number: 59P2107
Printed in the United States of America.
59P217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement