CR8PM-12B Datasheet

CR8PM-12B Datasheet
Preliminary Datasheet
CR8PM-12B
R07DS0117EJ0100
Rev.1.00
Sep 03, 2010
Thyristor
Medium Power Use
Features




 Insulated Type
 Planar Passivation Type
 UL Recognized : Yellow Card No. E223904
IT (AV) : 8 A
VDRM : 600 V
IGT : 15 mA
Viso : 2000 V
Outline
RENESAS Package code: PRSS0003AA-A
(Package name: TO-220F)
2
1. Cathode
2. Anode
3. Gate
3
1
1
2 3
Applications
Switching mode power supply, regulator for autocycle, motor control, heater control, and other general purpose control
applications
Maximum Ratings
Parameter
Repetitive peak reverse voltage
Non-repetitive peak reverse voltage
DC reverse voltage
Repetitive peak off-state voltage
DC off-state voltage
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
Symbol
VRRM
VRSM
VR(DC)
VDRM
VD(DC)
Voltage class
12
600
720
480
600
480
Unit
V
V
V
V
V
Page 1 of 7
CR8PM-12B
Preliminary
Parameter
RMS on-state current
Average on-state current
Surge on-state current
I2t for fusing
Peak gate power dissipation
Average gate power dissipation
Peak gate forward voltage
Peak gate reverse voltage
Peak gate forward current
Junction temperature
Storage temperature
Mass
Isolation voltage
Symbol
IT (RMS)
IT (AV)
Ratings
12.6
8
Unit
A
A
ITSM
120
A
I2t
60
A2s
PGM
PG (AV)
VFGM
VRGM
IFGM
Tj
Tstg
—
Viso
5
0.5
6
10
2
– 40 to +150
– 40 to +150
2.0
2000
W
W
V
V
A
°C
°C
g
V
Conditions
Commercial frequency, sine half wave
180° conduction, Tc = 106°C
60Hz sine half wave 1 full cycle,
peak value, non-repetitive
Value corresponding to 1 cycle of half
wave 60Hz, surge on-state current
Typical value
Ta = 25°C, AC 1 minute,
each terminal to case
Electrical Characteristics
Parameter
Repetitive peak reverse current
Repetitive peak off-state current
On-state voltage
Gate trigger voltage
Gate non-trigger voltage
Gate trigger current
Holding current
Thermal resistance
Symbol
IRRM
IDRM
VTM
VGT
VGD
IGT
IH
Rth (j-c)
Rated value
Min.
Typ.
Max.
—
—
2.0/5.0
—
—
2.0/5.0
—
—
1.4
—
0.2/0.1
—
—
—
—
—
—
15
—
1.0
—
15
—
3.7
Unit
Test conditions
mA
mA
V
Tj = 125°C/150°C, VRRM applied
Tj = 125°C/150°C, VDRM applied
V
V
mA
mA
°C/W
Tc = 25°C, ITM = 25 A,
instantaneous value
Tj = 25°C, VD = 6 V, IT = 1 A
Tj = 125°C/150°C, VD = 1/2 VDRM
Tj = 25°C, VD = 6 V, IT = 1 A
Tj = 25°C, VD = 12 V
Junction to caseNote1
Notes: 1. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W.
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
Page 2 of 7
CR8PM-12B
Preliminary
Performance Curves
Rated Surge On-State Current
Maximum On-State Characteristics
103
200
Surge On-State Current (A)
102
101
1
2
3
4
× 100 (%)
Gate Trigger Current (Tj = t°C)
Gate Voltage (V)
× 100 (%)
Gate Trigger Voltage (Tj = t°C)
Gate Trigger Voltage (Tj = 25°C)
PGM = 5W
PG(AV)
= 0.5W
IGT = 15mA
VGD = 0.2V
101
IFGM = 2A
102
103
103
Typical Example
102
101
100
–40
0
40
80
160
120
Gate Current (mA)
Junction Temperature (°C)
Gate Trigger Voltage vs.
Junction Temperature
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
Typical Example
102
–40
102
101
Gate Trigger Current vs.
Junction Temperature
103
101
40
Gate Characteristics
VGT = 1V
10-1
80
Conduction Time (Cycles at 50Hz)
VFGM = 6V
100
120
On-State Voltage (V)
102
101
160
0
100
5
Gate Trigger Current (Tj = 25°C)
100
0
0
40
80
120
Junction Temperature (°C)
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
160
Transient Thermal Impedance (°C/W)
On-State Current (A)
Tc = 125°C
102
101
100
10–1 –3
10
10–2
10–1
100
101
Time (s)
Page 3 of 7
CR8PM-12B
Preliminary
Allowable Case Temperature vs.
Average On-State Current
(Single-Phase Half Wave)
Maximum Average Power Dissipation
(Single-Phase Half Wave)
160
16
Case Temperature (°C)
Average Power Dissipation (W)
20
180°
12
120°
90°
θ = 30°
60°
8
θ
4
0
360°
2
4
6
8
10
12
14
Resistive,
inductive loads
100
80
180°
60
120°
90°
40
60°
θ = 30°
2
4
6
8
10
14
12
16
Average On-State Current (A)
Average On-State Current (A)
Maximum Average Power Dissipation
(Single-Phase Full Wave)
Allowable Case Temperature vs.
Average On-State Current
(Single-Phase Full Wave)
160
16
180°
θ = 30°
12
120°
90°
60°
8
θ
4
θ
360°
Case Temperature (°C)
Average Power Dissipation (W)
360°
0
0
16
20
Resistive
loads
140
0
2
4
6
8
10
12
80
180°
60
120°
90°
40
0
0
16
θ
100
60°
20
14
θ
360°
120
θ = 30°
Resistive loads
0
2
4
6
8
10
12
14
Average On-State Current (A)
Average On-State Current (A)
Maximum Average Power Dissipation
(Rectangular Wave)
Allowable Case Temperature vs.
Average On-State Current
(Rectangular Wave)
20
16
90° 120°
12
DC
270°
θ = 30°
8
θ
4
360°
2
4
6
8
10
12
14
Average On-State Current (A)
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
16
θ
360°
120
100
80
60
40
20
Resistive,
inductive loads
0
Resistive,
inductive loads
140
60°
0
16
160
180°
Case Temperature (°C)
Average Power Dissipation (W)
θ
120
20
Resistive,
inductive loads
0
140
0
0
180° 270°
60°
DC
θ = 30° 90° 120°
2
4
6
8
10
12
14
16
Average On-State Current (A)
Page 4 of 7
Breakover Voltage vs.
Junction Temperature
160
Typical Example
140
120
100
80
60
40
20
0
–40
0
40
80
120
160
Breakover Voltage vs.
Rate of Rise of Off-State Voltage
160
Tj = 125°C
Typical Example
140
120
100
80
60
40
20
0
101
102
103
104
Repetitive Peak Reverse Voltage vs.
Junction Temperature
160
Typical Example
140
120
100
80
60
40
20
0
–40
0
40
80
120
160
Junction Temperature (°C)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage
160
Tj = 150°C
Typical Example
140
120
100
80
60
40
20
0 1
10
102
103
104
Rate of Rise of Off-State Voltage (V/μs)
Rate of Rise of Off-State Voltage (V/μs)
Holding Current vs.
Junction Temperature
Turn-Off Time vs.
Junction Temperature
103
100
Typical Example
Turn-Off Time (μs)
Holding Current (Tj = t°C)
× 100 (%)
Holding Current (Tj = 25°C)
Breakover Voltage (dv/dt = vV/μs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/μs)
Junction Temperature (°C)
Repetitive Peak Reverse Voltage (Tj = t°C)
× 100 (%)
Repetitive Peak Reverse Voltage (Tj = 25°C)
Preliminary
Breakover Voltage (dv/dt = vV/μs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/μs)
Breakover Voltage (Tj = t°C)
× 100 (%)
Breakover Voltage (Tj = 25°C)
CR8PM-12B
102
IT = 8A, –di/dt = 5A/µs,
VD = 300V, dv/dt = 20V/µs
VR = 50V
80
60
40
Typical Example
20
Distribution
101
–40
0
40
80
120
Junction Temperature (°C)
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
160
0
0
20
40
60
80 100 120 140 160
Junction Temperature (°C)
Page 5 of 7
CR8PM-12B
Preliminary
Gate Trigger Current (tw)
× 100 (%)
Gate Trigger Current (DC)
Gate Trigger Current vs.
Gate Current Pulse Width
103
Typical Example
102
101 -1
10
100
101
102
Gate Current Pulse Width (μs)
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
Page 6 of 7
CR8PM-12B
Preliminary
Package Dimensions
Package Name
TO-220F
JEITA Package Code
SC-67
RENESAS Code
PRSS0003AA-A
Previous Code
⎯
MASS[Typ.]
2.0g
Unit: mm
10.5Max
2.8
17
8.5
5.0
1.2
5.2
φ3.2±0.2
13.5Min
3.6
1.3Max
0.8
2.54
0.5
2.6
4.5
2.54
Order Code
Lead form
Straight type
Lead form
Standard packing
Vinyl sack
Plastic Magazine (Tube)
Quantity
100
50
Standard order code
Type name
Type name – Lead forming code
Standard order
code example
CR8PM-12B
CR8PM-12B-A8
Note : Please confirm the specification about the shipping in detail.
R07DS0117EJ0100 Rev.1.00
Sep 03, 2010
Page 7 of 7
Notice
1.
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas
Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to
be disclosed by Renesas Electronics such as that disclosed through our website.
2.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
3.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
5.
When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and
regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to
the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is
prohibited under any applicable domestic or foreign laws or regulations.
6.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
7.
Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas
Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the
use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics.
The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard":
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools;
personal electronic equipment; and industrial robots.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically
designed for life support.
"Specific":
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical
implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
9.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
7F, No. 363 Fu Shing North Road Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2010 Renesas Electronics Corporation. All rights reserved.
Colophon 1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement