UG_TE100-P1U(v2.3R)
TABLE OF C ONTENTS
ABOUT THIS GUIDE .................................................................................. 4
INTRODUCTION ......................................................................................... 5
PACKAGE CONTENTS .................................................................................... 6
SYSTEM REQUIREMENTS ............................................................................... 6
GENERAL FEATURES ..................................................................................... 7
PRODUCT VIEW............................................................................................. 8
HARDWARE INSTALLATION ............................................................... 10
NETWORKING APPLICATION ....................................................................... 10
INSTALLING THE PRINT SERVER .................................................................. 11
USING THE UTILITIES ........................................................................... 12
AUTO-RUN INSTALLATION ......................................................................... 13
PS-UTILITY ................................................................................................. 14
Installing PS-Utility ................................................................................ 14
Using PS-Utility ...................................................................................... 15
PS WIZARD ................................................................................................. 18
WEB CONFIGURATION .......................................................................... 24
WEB CONFIGURATION UTILITY .................................................................. 24
HOME.......................................................................................................... 25
SETUP WIZARD ........................................................................................... 26
Second HTTP Port .................................................................................. 28
Save to Print Server ................................................................................ 28
CHANGE IP ADDRESS .................................................................................. 30
PRINTER INFORMATION ............................................................................... 31
FACTORY RESET ......................................................................................... 32
FIRMWARE UPGRADE .................................................................................. 33
ABOUT ........................................................................................................ 34
PRINTING IN WINDOWS 95/98/ME ...................................................... 35
INSTALLING THE LPR FOR TCP/IP PRINTING CLIENT ................................. 36
-2-
ADDING LPR PRINTER PORTS ..................................................................... 38
PRINTING FROM WINDOWS 95/98/ME ......................................................... 40
SETTING TCP/IP PRINTING SETTINGS ......................................................... 43
A BOUT THIS G UIDE
PRINTING IN WINDOWS 2000/XP/VISTA ........................................... 45
SETTING UP WINDOWS 2000 TCP/IP PRINTING .......................................... 45
SETTING UP WINDOWS XP TCP/IP PRINTING ............................................. 53
SETTING UP WINDOWS VISTA TCP/IP PRINTING ........................................ 62
PRINTING IN MAC OS ............................................................................ 68
RENDEZVOUS USES IN MAC OS 10.2 ......................................................... 68
This manual provides instructions and illustrations on how to use your
TE100-P1U USB 2.0 Print Server, including:
z
Chapter 1, Introduction, provides the general information on
the product.
z
Chapter 2, Hardware Installation, describes the hardware
installation procedure for the product.
z
Chapter 3, Using the Utilities, helps you to install and use the
software.
z
Chapter 4, Web Configuration, completes the configuration
using the web browser.
z
Chapter 5, Printing in Windows XP, lets you complete printing
task through your print server in Windows XP environment.
z
Chapter 6, Printing in MAC OS, lets you complete printing task
through your print server in MAC OS environment.
Please note that the illustrations or setting values in this manual are
FOR YOUR REFERENCE ONLY. The actual settings and values
depend on your system and network. If you are not sure about the
respective information, please ask your net work administrator or MIS
staff for help.
-3-
-4-
1
I NTRODUCTION
Package Contents
Unpack the package and check all the items carefully, and be certain
that you have:
♦ One TE100-P1U
♦ One AC Power Adapter suitable for your country’s electric power
service.
Congratulations on purchasing your TE100-P1U USB 2.0 Print
Server, the easiest and fastest way to deploy printers on your network.
This compact print server can connect your network through an
Access Point under the infrastructure mode, or can be used in ad-hoc
mode for direct communication between PC/Notebook and print
server anywhere you wish to locate printer services. It manages the
flow of print files from your workstation or file server to its connected
printers, delivering print jobs to high-performance printers much
faster than a file server or a PC acting as a print server can.
The pocket-sized Print Server features a Web-based Configuration
Utility, which allows you to set up the print server through the web
browser easily and quickly. It also includes a simple software utility
PS-Utility, a user-friendly program that allows you to complete
settings for the print server.
♦ One Quick Installation Guide.
♦ One Installation CD-ROM containing the PS-Utility program and
the User’s Guide.
If any item contained is damaged or missing, please contact your local
dealer immediately. Also, keep the box and packing materials in
case you need to ship the unit in the future.
System Requirements
♦ Operating System:
Microsoft Windows 95/98/ME/NT/2000/XP/2003/Vista.
Apple Mac OS X or above
♦ For Web Configuration:
Java-enabled web browser, such as Microsoft® Internet
Explorer 5.0 and Netscape Navigator 6.0.
-5-
-6-
General Features
Product View
♦
♦
♦
This section describes the externally visible features of the print
server.
♦
♦
♦
♦
♦
♦
♦
♦
Compliant with USB 2.0 Hi-Speed printing
Equipped 10/100 Auto-MDIX Fast Ethernet LAN port
Multi protocol support is ideal for shared printing in mixed-LAN
environments
Windows-based program makes it possible to set up in a few
minutes.
Offer LPR program for Windows 95/98/Me TCP/IP printing
Supports DHCP IP assign function
Supports Web configuration
Provides Flash memory for easy firmware upgrading
Supports IPP for Windows 2000/XP/Vista
Supports second http port for remote web configuration and IPP
printing.
Supports Mac OS 10.2 “Rendezvous” zero-configuration feature
Front View
LEDs*
Rear View
DC Power Input –
plug the AC Power
Adapter to this jack.
Reset Button –
Restore to factory
default setting
-7-
LAN Connector –
plug your LAN cable
to this connector.
USB Port – connect
the print server to a
Printer Port
-8-
2
* There are three green LED indicators on the rear panel:
LEDs
Power
Description
Steady light confirms that the Print Server is
powered on.
USB
When it is blinging, the connected printer is printing
Link/Act
Steady light confirms that the print server has a
good connection to your network.
When it is blinking (briefly dark), the print server is
receiving/ transmitting data from/to the network.
H ARDWARE
I NSTALLATION
Networking Application
The following diagram explains the application of your print server.
Pocket-sized Print Server
-9-
- 10 -
3
Installing the Print Server
Follow these steps for a trouble-free start of print server operations
with your TE100-P1U USB 2.0 Print Server.
1. Confirm proper operation of the printer to be connected to the print
server.
2. When you have confirmed proper operation of the printer, turn off
the power.
3. Confirm that your network is operating normally.
4. Connect the print server to the network (through the RJ-45
connector of the print server).
U SING T HE U TILITIES
This chapter describes the software utilities for the print server,
including how to set up your print server with these utility. The PSUtility is designed with a user-friendly interface that allows you to set
up and administer the print server easily.
5. While the printer is powered off, connect the print server to the
printer’s port.
6. Turn on the printer’s power.
7. Connect the DC end of the AC Power adapter to the DC power
input socket of the print server and the AC end to the wall outlet.
This will supply power to the print server immediately.
NOTE: The printer default IP address. To prevent from any conflict
in your network, it is recommended to use the PS-Utility program to
change the IP setting when there is some other device’s IP
Address is the same as the print server’s default IP Address.
- 11 -
- 12 -
Auto-Run Installation
Insert the Installation CD-ROM into your computer’s CD-ROM drive
to initiate the Auto-Run program, and the menu screen will appear as
below.
PS-Utility
To avoid the conflict in your network, you can use PS-Utility to
change the related settings of your print server (such as the IP address)
after finishing the installation.
Installing PS-Utility
1. Click Install Utility from the Auto-Run menu screen. Once
executed, the Setup program will extract files to launch the
InstallShield Wizard; then, click Next > in the welcome screen of
InstallShield Wizard.
• PS Wizard – click to setup printer port connectivity
• Utility – click to install PS-Utility. Please refer to the next
section for detailed information on installing the utility.
2. Choose the destination location. If no specific requirement,
leave the default setting and click Next >.
• User's Guide – click to preview the User's Guide in PDF format
for detailed information of the Print Server.
• Product Registration– click to register your product on-line
• Exit – click to close the Auto-Run program.
.
- 13 -
- 14 -
3. The InstallShield Wizard starts to install the software, and the
Progress bar indicates the installation is proceeding.
2. The main screen will appear as below, and it starts to search the
connected print server within the network.
4. When completed, click Finish.
Your print server
After installing the utility, the application program for the print server
is automatically installed to your computer, and creates a folder in
Start\Programs\PS-Utility.
Using PS-Utility
This section describes the operation of PS-Utility.
Utility:
To launch PS-
1. Click Start -> Programs -> PS-Utility, and then click the PSUtility item.
Component Features:
1. Device List: Display the connected print server within the
network.
2. Control Buttons
- 15 -
- 16 -
-
-
-
Change IP Address:
Click this button to bring
up the following dialog
box, allowing you to
change the IP Address.
In this dialog box, you can
select either Manually
Assign or DHCP Assign
Automatically. When
completed, click OK.
Update Firmware: Click this button to update the firmware
of the selected print server.
Show Web Setup: Click this button to open your web
browser and launch the Configuration Utility. Alternately,
you can double-click the print server in the Device List to
launch the Configuration Utility.
Factory Reset: Click this button to reload the factory settings
of the print server.
Discover Device: Click this button to search the connected
print server again.
About: Click this button to bring up a window containing the
basic information of PS-Utility.
Close: Click this button to exit PS-Utility.
PS Wizard
Note: The PS Wizard doesn’t support Windows 95. The user can
refer chapter 5 “Printing in Windows 95/98/ME” to set up for
printing with Windows 95.
PS Wizard is a convenient utility that allows you to set up the print
server’s port connection.
Windows 2000/XP/2003/Vista
1) Insert the Installation CD-ROM into your computer’s CDROM drive. Click PS Wizard and then click ME/98SE from
the Auto-Run menu screen.
3. Information Field: Display the basic information of the selected
print server in the Device List.
4. Status Bar: Display the system status.
- 17 -
- 18 -
2) Select the print server, select the desired port and then click
Add Printer.
4) Click Next.
5) Click Print Test Page.
3) Click Select from manufacturer list. Select the appropriate
driver for your printer and then click Next.
6) Click OK.
- 19 -
- 20 -
7) Click Finish.
8) Repeat steps 1 to 7 to add the printer to other computers on
the network.
Windows 98SE/ME :
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive, and click PS Wizard from the Auto-Run menu screen.
The welcome screen appears as below. Click Next >.
NOTE: For some specific printers, you may need to connect the
printer to the computer and install the driver. In this case, connect
it to the computer and install the driver first, and then connect it to
the print server.
2. In the following window, select one printer in the Printer List to
set up port connection, and then click Next >.
- 21 -
- 22 -
4
W EB C ONFIGURATION
Choose one connected
printer within the network.
3. Select one printer port in the Print Server List, and click Next
You can access and manage the Print Server through: 1) the enclosed
software PS-Utility, and 2) a web browser. This chapter describes
the second method – the Web Configuration Utility, and explains how
to set up your print server with the web browser.
Web Configuration Utility
First, launch your web browser (such as the Internet Explorer 6.0 used
in this manual). Then, type http://192.168.0.1 (the default IP
address) in the Address bar and press [Enter] to enter the Management
screen of the Configuration Utility.
Your print server name
Your printer port name
Choose one connected
printer port.
TIP: The computer’s IP address must correspond with the print
server’s IP address in the same segment for the two devices to
communicate. Extensive knowledge of LAN will be helpful in
configuring the print server.
>
- 23 -
- 24 -
Home
Setup Wizard
The Management Screen of the Configuration Utility
The Home screen displays the basic information of the print server. As
shown above, the System displays the status of your print server and
network. Clicking Refresh will update the information.
The “Setup Wizard” will lead you to change all the configurations
step by step. Please follow below steps to finish it
System
Server Name: Assign a name to the print server.
Port Name: Assign the Port Name for the print server
Password: Enter the Administrator password (1-8 characters).
- 25 -
NOTE: Passwords are limited to 8 alphanumeric characters,
having more than 8 characters will invalidate the password
protection. After setting up the password, the login screen will
prompt you for the password the next time you login. The User
Name is “admin” and the password
- 26 - is what you have assigned.
Microsoft Network
Enter the name of the Workgroup that you want the print server
associated with in this field.
IP Address
This option allows you to set the IP address manually or
automatically. When you choose Manually Assign, you should enter
the related information in the following boxes, including IP Address,
Subnet Mask, and Default Gateway.
Second HTTP Port
This field allows settings to open a second port for the remote printing
and IPP printing function. This will permit users to execute printing
jobs through broadband IP router.
Save to Print Server
Please verify the configurations and click “Yes” to save settings.
- 27 -
- 28 -
Change IP Address
The Setup Wizard is now completed.
This feature is helping you to change IP address only.If you have run
the Setup Wizard already, you may skip this procedure. Please type in
IP address that applies to your existing network (i.e. 192.168.X.X)
Type in the Default Gateway (i.e. your router’s local IP address).
- 29 -
- 30 -
Printer Information
Factory Reset
Please click Yes to reload the factory settings of the print server.
“Printer Information” will display all printer information such as
Manufacturer, Model Number, Command Set and Status.
- 31 -
- 32 -
Firmware Upgrade
About
This screen displays the information of the print server.
The firmware can be easily upgrade through “Firmware Upgrade”
feature. Click Browse to get the firmware file, and then click
Upgrade to flash firmware. The new firmware can be downloading
from www.trendnet.com once it is available.
- 33 -
- 34 -
5
P RINTING
IN
W INDOWS
95/98/ME
The Print Server can provide print services to TCP/IP networks using
the lpr/lpd network printing protocol. Most UNIX systems are
capable of supporting lpd, as is Windows NT/2000.
This LPR for TCP/IP Printing client gives Windows 95/98/Me
workstations the ability to print using the lpr/lpd printing protocol.
Though it is possible to print to Print Servers from Windows
95/98/Me, this capability is useful if primarily administer your
network from UNIX systems, or if you want to print from workstations
that are only accessible through IP routing.
Installing the LPR for TCP/IP
Printing Client
Before your Windows 95/98/Me workstation can print using the lpr
protocol, you will need to install the client program, as follows:
1. Make sure that you have installed the TCP/IP protocol, and
have properly configured the Windows 95/98/Me TCP/IP
settings. You can install the protocol from the Network
control panel if necessary.
2. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
3. Double-click on the Network icon in the Control Panel folder.
4. Click on the Add... button on the Configuration tab.
5. Windows will ask for the type of component to add. Select
Client and click Add... to continue.
6. When Windows asks you to select a network client, click the
Have Disk... button.
- 35 -
- 36 -
7. Insert the Print Server installation CD in your computer’s CDROM, enter the proper pathname (for example , D:\ lpr), and
click OK.
8. Select the LPR for TCP/IP Printing client and click OK.
Adding LPR Printer Ports
Once you have installed the client, and have enabled TCP/IP printing
for the Print Servers, then you need to add a printer port for each
printer you will be printing to using the lpr/lpd protocol. To add a
printer port,
1. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
2. Double-click on the Network icon in the Control Panel folder.
9. Windows will copy the necessary files, and return to the
Network dialog.
Click OK to let Windows restart.
3. Choose the LPR for TCP/IP Printing client and click the
Properties button.
- 37 -
- 38 -
4. Click the Add Port... button to add a new lpd-accessible printer
port.
5. Enter the IP address of the Print Server and the name of the
printer port that you will be printing to, then press OK.
Hint: You can get the Port name from the print server’s system
information through web browser. Please refer page 25.
Printing from Windows 95/98/Me
After you have added the necessary printer ports, you can add a
printer device for printing to the port. To enable printing to an lpraccessible printer port from Windows 95/98/Me,
1. From the Start menu, choose the Settings submenu, then the
Printers item within it.
folder.
Windows will display the Printers
2. Double-click on the Add Printer icon in the Printers folder.
6. Click OK to leave the LPR for TCP/IP Printing Properties
Windows will start the Add Printer Wizard.
window.
Click the Next > button to continue to the next screen.
3. Choose the Network Printer selection and click the Next >
button to continue.
- 39 -
- 40 -
Press OK when you have located the proper printer port.
Click Next > to continue to the next step.
5. At this point Windows will ask you to choose the correct printer
driver for the printer. Choose you printer’s make and model
from the list, or use the driver disk included with the printer.
When you have chosen the correct printer, click Next > to
continue.
6. Windows will then ask for a name for the new printer, and ask
4. Enter the name of the port, as displayed in the LPR for TCP/IP
Printing Port List.
Alternatively, you can click Browse... and locate the printer port.
TCP/IP printing ports are located under the Entire Network icon,
within the Print Servers - TCP/IP LPR icon.
- 41 -
whether or not you want to set the printer as the Windows
default printer. Click Finish (or Next >) to continue.
7. Windows may ask you whether or not you wish to print a test
page to make sure that the printer will work correctly. When
the test page is done printing, you will be asked whether or not
the test page printed.
- 42 -
Setting TCP/IP Printing Settings
The lpr client’s Properties dialog allows you to change several of the
client’s settings. To change these settings,
1. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
2. Double-click on the Network icon in the Control Panel folder.
3. Choose the LPR for TCP/IP Printing client and click the
Properties button.
The parameters are as follows:
♦ Communication Timeout Determines how long, in seconds,
the system will wait before determining that it has lost
connection with lpr/lpd print servers.
♦ Retry Interval Determines how long, in seconds, the system
will wait before retrying a lost connection.
♦ Retry Times Determines how many times the system will
retry a lost connection with an lpr/lpd print server. If Infinite
is checked, it will retry indefinitely.
♦ Spool Path Gives the directory path where the system will
temporarily store lpr/lpd print server job files.
4. Click on the Settings tab to access the lpr client settings.
Change the settings as necessary, and press OK to let the
changes take effect.
- 43 -
- 44 -
6
Create a new “Standard TCP/IP Port”
P RINTING IN W INDOWS
2000/XP/VISTA
Setting Up Windows 2000 TCP/IP Printing
Following is the correct procedure for setting up TCP/IP LPR printing
under Windows 2000.
Click Start > Settings > Printers. Double Click “Add Printer”
Select “Local Printer”
- 45 -
Click “Next”
- 46 -
Input the IP Address of the Print Server, and the Port name of the Port
that will be printed to, then click “Next”.
Select “LPR”, and put the Port name in the field labeled “Queue
Name”. Then Click “OK”.
Hint: You can get the Port name from the print server’s system
information through web browser. Please refer page 25.
Select “Custom”, and click “Settings”.
- 47 -
- 48 -
Click “Next”.
The Printer Install Wizard will now prompt for drivers. Select the
correct Make and Model, or click “Have Disk”, to provide the
Manufacturer’s Driver Disk.
Click “Finish”
Click “Next”.
- 49 -
- 50 -
Also, a Test Page can be printed to confirm proper configuration.
Select a “Printer Name”.
When the Test Page has been printed, click “Finish” to complete the
installation.
Sharing can be enabled here.
- 51 -
- 52 -
Setting Up Windows XP TCP/IP Printing
Select “Local Printer”
Following is the correct procedure for setting up TCP/IP LPR printing
under Windows XP.
Click Start > Printer and Faxes
Double Click “Add a Printer”
Click “Next”
Create a new “Standard TCP/IP Port”
- 53 -
- 54 -
1Select “Custom”, and click “Settings”.
Click “Next”
Input the IP Address of the Print Server, and the Port name of the Port
that will be printed to, then click “Next”.
Select “LPR”, and put the Port name in the field labeled “Queue
Name”. Then Click “OK”.
Hint: You can get the Port name from the print server’s system
information through web browser. Please refer page 25.
- 55 -
- 56 -
Click “Finish”
Click “Next”.
- 57 -
- 58 -
The Printer Install Wizard will now prompt for drivers. Select the
correct Make and Model, or click “Have Disk”, to provide the
Manufacturer’s Driver Disk.
Click “Next”.
A Test Page can be printed to confirm proper configuration.
Select a “Printer Name”.
- 59 -
- 60 -
When the test page has been printed, click “Finish” to complete the
installation.
Setting Up Windows Vista TCP/IP
Printing
Following is the correct procedure for setting up TCP/IP LPR printing
under Windows Vista.
Click Start > Control Panel > Printers
Click “Add a Printer”
Click “Add a local printer”
- 61 -
- 62 -
Select Create a new port, select Standard TCP/IP Port and then
click Next.
Input the IP Address of the Print Server, and the Port name of the Port
that will be printed to, then click “Next”.
Select “Custom”, and click “Settings”.
Select “LPR”, and put the Port name in the field labeled “Queue
Name”. Then Click “OK”.
Hint: You can get the Port name from the print server’s system
information through web browser. Please refer page 25-26.
- 63 -
- 64 -
Select a “Printer Name”.
Click “Next”.
A Test Page can be printed to confirm proper configuration.
The Printer Install Wizard will now prompt for drivers. Select the
correct Make and Model, or click “Have Disk”, to provide the
Manufacturer’s Driver Disk. Click “Next”.
- 65 -
- 66 -
7
Once a test page has been sent to your printer, click Close.
P RINTING IN MAC OS
Rendezvous Uses in MAC OS 10.2
Click Finish.
The latest version of MAC OS provides a new feature that is called
Rendezvous. Rendezvous is a revolutionary networking technology
standard that lets you create an instant network of computers and
devices, which can be used throughout Mac OS 10.2 to provide
innovative ways to share files and printers and even contact other
people on the network.
For the printer connection, the Mac OS 10.2 Print Center application
uses Rendezvous to discover Rendezvous-enabled printers on the
network. When you add your computer to a network, Print Center
automatically discovers the available printers. All you have to do is
selecting the one you want to use and then start printing. You can
add a new printer to the network and all the users on the network will
see the new printer automatically appear in their Print Center, without
any configuration.
The following instructions provide a common procedure of installing
the printer:
- 67 -
- 68 -
1. Launch Print Center.
Add button.
Press and hold the Option key, click the
4. Select the desired printer, and the following pop-up menu displays
the printer’s manufacturer. Select Generic.
2. Select Rendezvous from the pop-up menu.
5. The printer is installed into the system successfully.
3. When clicking the Rendezvous item, the following window
appears to display the connected Rendezvous-enabled printers.
Connected printer(s)
- 69 -
- 70 -
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship,
under normal use and service, for the following lengths of time from the date
of purchase.
TE100-P1U – 5 Years Warranty
If a product does not operate as warranted above during the applicable
warranty period, TRENDnet shall, at its option and expense, repair the
defective product or part, deliver to customer an equivalent product or part to
replace the defective item, or refund to customer the purchase price paid for
the defective product. All products that are replaced will become the property
of TRENDnet. Replacement products may be new or reconditioned.
TRENDnet shall not be responsible for any software, firmware, information, or
memory data of customer contained in, stored on, or integrated with any
products returned to TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or
attempt to service the product by any unauthorized service center. This
warranty is voided if (i) the product has been modified or repaired by any
unauthorized service center, (ii) the product was subject to accident, abuse, or
improper use (iii) the product was subject to conditions more severe than
those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within the
applicable warranty period for a Return Material Authorization (RMA) number,
accompanied by a copy of the dated proof of the purchase. Products
returned to TRENDnet must be pre-authorized by TRENDnet with RMA
number marked on the outside of the package, and sent prepaid, insured and
packaged appropriately for safe shipment.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT
OPERATE AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY
SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACEMENT. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE
IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS
TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT
IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S
OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR
OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE
INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW
TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY
LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION
OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF
SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,
REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT
TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES
WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL
FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the
state of California.
AC/DC Power Adapter, Cooling Fan, Cable and Power Supply carry - 1 Year Warranty
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement