cypress_CDPS-84HB_User_Manual

CDPS-84HB
8 by 4 Digital Presentation Scaler
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2012 by Cypress Technology.
All Rights Reserved.
Version 1.0 October 2009
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
RDV1
05/05/14
Preliminary Release
RDV2
09/15/14
Add RS-232 Commands
CONTENTS
1. Introduction�� 1
2. Applications�� 1
3. Package Contents�� 1
4. System Requirements�� 1
5. Features�� 2
6. Operation Controls and Functions�� 3
6.1 Front Panel��3
6.2 Rear Panel��4
6.3 Remote Control ��5
6.4 IR Pin Assignment��6
6.5 RS-232 Pin Assignment��7
6.6 RS-232/Telnet Commands��8
6.7 OSD Menu��11
7. Connection Diagram�� 15
8. Specifications�� 16
8.1 Input Resolution Support��17
8.2 Output Resolution Support ��18
9. Acronyms�� 19
1. INTRODUCTION
This HDBaseT™ capable 8 by 4 Digital Presentation Scaler can switch
and scale HDMI/HDBaseT/PC/Composite Video signals from any one
of its eight inputs and simultaneously display it on any of its HMDI or
HDBaseT outputs. The unit has and HDMI bypass output, allowing local
monitoring of any of the HDMI or HDBaseT inputs, and features full
5play™ convergence for easy integration of compatible transmitters
and receivers. It has the added benefit of control via IR remote
control, RS-232, IP/Telnet and WebGUI, with all information including
system status presented on its comprehensive LCD display.
2. APPLICATIONS
• Home Theater/Entertainment
• Lecture Room/Hall Presentation
• Show Room/Demo Room
• Public Commercial Display
• Information Board
3. PACKAGE CONTENTS
• 1 x 8 by 4 Presentation Scaler
• 1 x IR Extender Cable
• 1 x IR Receiver Cable
• 1 x Remote Control with Battery
• 1 x 24V/ 2.7A DC Power Adaptor
• 1 x Power Cord
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-Box
and output HDMI TV/Display and or audio amplifier with connection
cables.
1
5. FEATURES
• HDMI, HDCP and DVI compliant
• Full 5Play™ convergence: Video, Audio, LAN serving, Power over
Cable (PoC) and Control (IR & RS-232 bypass)
• Supports distances of up to 100 meters over industry standard
CAT5e/6/7 cable
• Supports scaling of any input signals to a wide range of HDTV and
PC output resolutions up to 1080p and WUXGA (RB)
• Digital to Analog and Analog to Digital Audio conversion (DAC/
ADC)
• Simultaneous video output of the selected source through the
HDBaseT and HDMI outputs and audio output through the digital
coaxial and analog L/R outputs
• Features four HDMI inputs with corresponding L/R audio inputs
(3.5mm mini-jack), two HDBaseT CAT5e/6/7 inputs, PC (15-pin D-Sub)
with L/R audio (3.5mm mini-jack) and Composite Video and L/R
audio (3 RCA)
• Features two HDMI outputs, one HDBaseT CAT5e/67 outputs, one
Digital Coaxial audio output and one L/R audio 3.5mm mini-jack
output
• Supports switchable HDMI bypass allowing local monitoring of any
of the HDMI or HDBaseT inputs
• Supports Power over Cable on the CAT5e/6/7 output to a
compatible Receiver
• Supports control via IR, Remote control, RS-232, Telnet WebGUI and
on-panel controls
• Supports HDBaseT LAN serving function to compatible Receivers
Note: The PoC function is only designed for powering compatible
Receiver units only---non-PoC Receiver will need their own
power supply. Receivers of another brand may not be compatible.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
4
1
2
3
4
5
6 7
8
9 10
3
5 6
7
1 POWER: Press this button to turn ON the device and the LED will
illuminated.
2 IR Window: This IR receiver receives only the remote control signal
from the packaged included remote control.
3 INPUT HDMI 1~4 & LED: Press the IN buttons to select an input source
signal from the 4 HDMI input sources to be display for output ports.
The LED will illuminate according to the selection.
4 BYPASS & LED: Press these buttons to select an input source signal
from the 6 input sources to be display for BYPASS output port. The
LED will illuminate according to the selection.
5 INPUT CAT5e/6/7 5~6 & LED: Press the IN buttons to select an input
source signal from the 2 CAT5e/6/7 input sources to be display for
output ports. The LED will illuminate according to the selection.
6 INPUT PC & LED: Press this button to select PC input source signal to
be display for PC output port. The LED will illuminate according to
the selection.
7 INPUT CV & LED: Press this button to select CV input source signal s
to be display for CV output port. The LED will illuminate according
to the selection.
8 MENU: Press this wheel to enter into the menu and press it again to
confirm the selection.
9 +/-: Press these buttons to move up/down under menu selection or
under volume control to adjust audio volume up/down.
10 ENTER: Press this button to confirm menu selection.
3
6.2 Rear Panel
1
IR OUT
2
6
5
7
8
AUDIO
IR IN
13
AUDIO
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
INPUT
R
DSP PROG.
OUTPUT
CAT5e/6/7
ON
SERVICE 1
COAX
HDMI 1
3
L
CV
16
AUDIO 7
8
BYPASS
CAT5e/6/7
CAT5e/6/7
PC
5
6
7
RS-232
LAN
SERVICE 2
HDMI 2
4
OFF
14
HDMI
7
9
HDMI 1
HDMI 2
HDMI 3
10
HDMI 4
11
12
DC 24 V
15 17
1 IR OUT: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
2 IR IN: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct lineof-sight of the IR Extender.
3 OUTPUT CAT5e/6/7: Connect to the Receiver unit with a Single
CAT5e/6/7 cable for transmission of all data signals.
4 OUTPUT HDMI: Connect to a HDMI equipped TV/monitor for display
of the HDMI input source signal.
5 OUTPUT COAX: Connect to audio sound equipment such as
speaker or amplifier for audio sound output.
6 OUTPUT AUDIO: Connect to audio sound equipment such as
speaker or amplifier for audio sound output.
7 SERVICE 1& 2: These slots are reserved for firmware update use
only.
8 DSP PROG Switch: This switch is reserved for firmware update use
only. Default setting is on OFF.
9 BYPASS: Connect to a HDMI equipped TV/monitor or DVI equipped
monitor with audio sound equipment such as speaker for both
video and audio output display.
10 INPUT HDMI 1~4 & AUDIO 1~4: Connect to HDMI source equipment
such as DVD or Blu-ray player along or to DVI source equipment
along with audio source signal.
11 INPUT CAT5e/6/7: Connect this port to HDMI to CAT5e/6/7
Transmitter with CAT5e/6/7 cable to extend the signal up to 100m.
12 INPUT PC & AUDIO: Connect this port to PC/Laptop with audio
signal for input signal selecting.
4
13 INPUT CV: Connect this port to source equipment such as video
player or Set-Top-Box for input signal selecting.
14 RS-232: Connect from PC/Laptop for RS-232 command sending to
control the device.
15 LAN: Connect from PC/Laptop with active internet service for Web
GUI control with RJ-45 terminated cable.
16 POWER Toggle: Switch this toggle to turn ON and OFF the device’s
power.
17 DC 24V: Connect the adaptor with power cord included in the
package and connect to AC wall outlet for power supply.
6.3 Remote Control
1 POWER:
Press this button to switch the device
ON or to put the device into Standby
mode.
2
2 MUTE:
Press these buttons one time each
to select input source for outputs
display.
4 MENU:
Press this button to enter into the OnScreen Menu.
5 EXIT:
Press this button to exit menu
selection.
6 ▲▼◄►& OK:
5
Press OK to confirm the selection
or use the directional buttons to
navigate the On-Screen-Menu.
POWER
HDMI 1
CAT5e/6/7
1
PC
HDMI 2
2
CV
1
3
HDMI 3
Press this button to mute output audio
sound.
3 INPUT:
MUTE
HDMI 4
INPUT
5
EXIT
MENU
-
+
OK
8
ADJUST
RESET
HDMI 1 CAT5e/6/7 1
HDMI 2 CAT5e/6/7 2
HDMI 3
HDMI 4
BYPASS
CR-135
4
6
7
9
7 ADJUST:
Press this button when output image is not fitting the display's
screen perfectly. The device will auto adjust the image to full
screen.
8 RESET:
Press this button to set the deivice back into the fatory default
setting.
9 BYPASS:
Press these buttons to select an input source for Bypass output port
to display.
6.4 IR Pin Assignment
IR Blaster
1 Power
2 IR Blaster Signal
3 NC
IR Receiver
1 IR Signal
2 Power
3 Grounding
6
6.5 RS-232 Pin Assignment
CDPS-84HB
Remote Control
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 19200bps
Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
7
►
◄
6.6 RS-232/Telnet Commands
COMMAND
DESCRIPTION
S SOURCE 1~8
1=HDMI 1
2=HDMI 2
3=HDMI 3
4=HDMI 4
R SOURCE
Reports the numerical equivalent for SOURCE
setting (as above)
S OUTPUT 0~21
0=640×480
1=800×600
2=1024×768
3=1280×768
4=1360×768
5=1280×720
6=1280×800
7=1280×1024
8=1440×900
9=1400×1050
10=1680×1050
R OUTPUT
Reports the numerical equivalent for OUTPUT
setting (as above)
S SIZE 0~6
0=OVERSCAN
1=FULL
2=FOLLOW INPUT
3=PAN SCAN
R SIZE
Reports the numerical equivalent for SIZE
setting (as above)
S INPUTHDCP 0/1
R INPUTHDCP
0=OFF 1=ON
Reports HDMI support HDCP status
S CONTRAST 0~60
Setups the numerical equivalent for
CONTRAST setting (as left)
R CONTRAST
Reports the numerical equivalent for
CONTRAST setting
S BRIGHTNESS 0~60
Setups the numerical equivalent for
BRIGHTNESS setting (as left)
5=HDBT 1
6=HDBT 2
7=PC
8=VIDEO
11=1600×1200
12=1920×1080
13=1920×1200
14=480p
[email protected]
[email protected]
[email protected]
18=576p
[email protected]
[email protected]
[email protected]
4=LETTER BOX
5=UNDER 2
6=UNDER 1
8
COMMAND
DESCRIPTION
R BRIGHTNESS
Reports the numerical equivalent for
BRIGHTNESS setting
S HUE 0~60
Setups the numerical equivalent for HUE
setting (as left)
R HUE
Reports the numerical equivalent for HUE
setting
S SATURATION 0~60
Setups the numerical equivalent for
SATURATION setting (as left)
R SATURATION
Reports the numerical equivalent for
SATURATION setting
S SHARPNESS 0~30
Setups the numerical equivalent for
SHARPNESS setting (as left)
R SHARPNESS
Reports the numerical equivalent for
SHARPNESS setting
S NR 0~3
0=OFF
1=LOW
R NR
Reports the numerical equivalent for the
NOISE REDUCTION setting (as above)
S VOLUME 0~100
R VOLUME
Volume Value
Reports Volume value
S AUDIO DELAY 0~3
0=OFF
1=40ms
R AUDIO DELAY
Reports the numeric equivalent for AUDIO
DELAY setting (as above)
S AUDIO MUTE 0/1
0=ON
R AUDIO MUTE
Reports the numeric equivalent for AUDIO
MUTE setting (as above)
S HDMIAUDIO 0/1
0=AUTO
1=EXT.
R HDMIAUDIO
Reports HDMI AUDIO Status
S KEY LOCK 0/1
0=Disable
R KEY LOCK
Reports the numeric equivalent for KEY
LOCK setting (as above)
S FREERUNCOLOR 0/1
0=Black
R FREERUNCOLOR
Reports the numeric equivalent for FREERUN
Colorsetting (as above)
9
2=MIDDLE
3=HIGH
2=110ms
3=150ms
1=MUTE
1=Enable
1=Blue
COMMAND
DESCRIPTION
S HDBTUART 0/1
0=HDBT1
R HDBTUART
Reports the numeric equivalent for HDBT
1=HDBT2
UART setting (as above)
S AUTO SCAN 0/1
0=OFF
R AUTO SCAN
Reports the numeric equivalent for AUTO
1=ON
SCAN setting (as above)
S BYPASS 1~6
R BYPASS
1=HDMI 1
4=HDMI 4
1=HDMI 2
5=HDBT 1
3=HDMI 3
6=HDBT2
Reports the numeric equivalent for BYPASS
setting (as above)
S RESET 1
Setups the numerical equivalent for RESET
setting (as left)
S POWER 0/1
0=OFF
R POWER
Reports the numeric equivalent for POWER
setting (as above)
PORT 0~8
1=HDMI
4=HDMI 4
7=PC
1=ON
2=HDMI 2
5=HDBT 1
3=HDMI 3
6=HDBT 2
8=VIDEO 0=Last Memory
VOL +
VOL -
Volume Value
Volume Value
ST
FW Version & Source
Note:
1. Only LPCM 2 channel digital audio is supported, please ensure
that the source audio is set to LPCM 2 channel audio in order to
avoid unnecessary audio noise.
2. RS-232 commands will be not executed unless followed with a
carriage return and LF. Commands are case-insensitive.
10
6.7 OSD Menu
1st Layer
2nd Layer
3rd Layer
DISPLAY
OUTPUT
640X480 60
800x600 60
1024x768 60
1280x768 60
1360x768 60
1280x720 60
1280x800 60
1280x1024 60
1440x900 60
1400x1050 60
1680x1050 60
1600x1200 60
1920x1080 60
1920x1200 60
720X480P 60
1280X720P 60
1920X1080I 60
1920X1080P 60
720X576P 50
1280X720P 50
1920X1080I 50
1920X1080P 50
11
Remark
DISPLAY
SIZE
OVER SCAN
FULL
FOLLOW INPUT
PAN SCAN
LETTER BOX
UNDER 2
UNDER 1
MODE INFO
OFF
INFO
ON
INPUT HDCP OFF
(HDMI mode ON
only)
PC
AUTO SETUP
Yes/No(Default No)
(PC mode
only)
H_POSITION
0~60
V_POSITION
0~60
PHASE
0~31
CLOCK
WXGA/XGA
XGA/WXGA(Default
XGA)
RESET
Yes/No(Default No)
12
COLOR
CONTRAST
0~60(Default 30)
BRIGHTNESS
0~60(Default 30)
COLOR
R
0~1023(Default 512)
G
0~1023(Default 512)
B
0~1023(Default 512)
R OFFSET
0~1023(Default 512)
G OFFSET
0~1023(Default 512)
B OFFSET
0~1023(Default 512)
HUE
0~60(Default 30)
SATURATION
0~60(Default 30)
SHARPNESS
0~30(Default 0)
NR.
OFF
LOW
MIDDLE
HIGH
AUDIO
0~100(Default 100)
VOLUME
DELAY
OFF
40mS
110mS
150mS
SOUND
ON
MUTE
AUTO
SOURCE
(HDMI mode EXT.
only)
13
SETUP
FACTORY RESET
KEY LOCK
OSD Setting back to
factory default
OFF
ON
POWER
SAVE
OFF
IP MODE
DHCP
ON
STATIC
SET STATIC IP IP ADDRESS
0.0.0.0~
255.255.255.255
(Default 192.168.0.1)
SUBNET MASK
0.0.0.0~
255.255.255.255
(Default 255.255.255.0)
Def. GATWAY
0.0.0.0~
255.255.255.255
(Default 192.168.0.254)
FREERUN
COLOR
BLUE
BLOCK
MISC.
HDBTOUT
(UART1)
HDBT1~2(Default
HDBT1)
Auto Scan
OFF
ON
INFORMATION INPUT:
OUTPUT:
REVISION:
IP ADDRESS:
Default settings are underlined.
14
7. CONNECTION DIAGRAM
1.5m
60°
IR BLASTER
Set-top Box
Router with
Blu-ray/DVD Internet
Connection
Player
60°
3m
7m
m
3m
IR Extender
Active
Speakers
RS-232 In
HDMI In
LAN
RS-232
Equipped PC
TX
Transmitter
HDMI to CAT5e/6 with LAN/IR/RS232
Smartphone
or Tablet
Active Speakers
100M
RS-232
Cable
INPUT
IR OUT
AUDIO
IR IN
AUDIO
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
INPUT
DSP PROG.
OUTPUT
CAT5e/6/7
ON
SERVICE 1
COAX
HDMI 1
HDMI 2
CAT5e/6
Output
100M
IR2 Blaster
RX
Power
IR1 Extender
OFF
L
CV
CAT5e/6/7
CAT5e/6/7
PC
AUDIO 7
5
6
7
RS-232
LAN
SERVICE 2
HDMI
HDMI
HDMI
HDMI
HDMI 11
HDMI
HDMI 22
HDMI 3
HDMI 4
DC 24 V
HDMI
Input
DVI to
HDMI
Output
Link
CAT5e/6 In
3D TV/
Display
R
8
BYPASS
Blu-ray
Player
Network
Router
Blu-ray or PS3 Player
PC
3D TV/
Display
DELL PC/
Laptop
15
Power
Supply
8. SPECIFICATIONS
Frequency bandwidth
Up to 10.2Gbps
Input Ports
4 x HDMI
4 x L/R
2 x CAT5e/6/7
1 x PC + L/R
1 x CV+L/R
2 x USB (Service only)
1 x LAN
1 x RS-232
1 x IR
Output ports
2 x HDMI
1 x HDMI Bypass
1 x CAT5e/6/7
1 x Coaxial
1 x L/R
Resolution
[email protected]/60, [email protected],
VGA~WUXGA(RB)
Audio Format
LPCM 2CH
ESD Protection
Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Power Supply
24VDC/2.7A (US/EU standards, CE/FCC/
UL certified)
Dimensions
438mm (W) x 269mm (D) x 44mm (H)/Jack
Excluded
438mm (W) x 275mm (D) x 44mm (H)/Jack
Included
Weight
3410g
Chassis Material
Metal
Silkscreen Color
Black
Operating Temperature
0˚C~40˚C / 32˚F ~ 104˚F
16
Storage Temperature
-20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity
20~90% RH (no condensation)
Power Consumption
8.1 Input Resolution Support
INPUT RESOLUTION
CV
PC
HDMI
NTSC/PAL

-
-
480i/576i
-
-

480p/576p
-
-

[email protected]/60 Hz
-
-

[email protected]/60 Hz
-
-

[email protected]/60 Hz
-
-

[email protected]/72/75 Hz
-


[email protected]/60/72/75 Hz
-


[email protected]/70/75 Hz
-


[email protected]/75 Hz
-


[email protected] Hz
-


1280×[email protected] Hz
-


1680×[email protected] Hz
-


1920×[email protected] Hz
-




1920 x [email protected]
[email protected]/25/30 Hz
17

8.2 Output Resolution Support
OUTPUT RESOLUTION
HDMI
480p/576p

[email protected]/60 Hz

[email protected]/60 Hz

[email protected]/60 Hz

[email protected] Hz

[email protected] Hz

[email protected] Hz

[email protected] Hz

[email protected] Hz

1280×[email protected] Hz

1280×[email protected] Hz

1360×[email protected] Hz

1400×[email protected] Hz

1440×[email protected] Hz

1680×[email protected] Hz

1920×[email protected] Hz

18
9. ACRONYMS
ACRONYM
COMPLETE TERM
COMP
Component Video
CV
Composite Video
DVI
Digital Visual Interface
EDID
Extended Display Identification Data
HDCP
High-Bandwidth Digital Content Protection
HDMI
High-Definition Multimedia Interface
IR
Infrared
OSD
On-screen Display (Menu)
USB
Universal Serial Bus
UXGA
Ultra Extended Graphics Array
VGA
Video Graphics Array
XGA
Extended Graphics Array
WUXGA
Wide Ultra Extended Graphics Array
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20140530 MPM-CDPS84HB