L A NU M

L A NU M
PL48
PL60
PL72
OPERATOR'S MANUAL
(Rev. 6/4/2014)
MAN0152
CORE AERATOR
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that
all Dealer Check List items have been completed. Dealers can register all Woods product at
dealer.WoodsEquipment.com under Product Registration.
Failure to register the product does not diminish customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better
and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and
become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals
can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at
www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:
Model: _______________________________
Date of Purchase: _____________________
Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.
2 Introduction
Gen’l (Rev. 3/28/2012)
SPECIFICATIONS
Core Aerator
PL48
PL60
PL72
Working Width
48"
60"
72"
Overall Width
54.5"
66.5"
78.5"
Number of Reels
8
12
12
Number of Spoons
64
96
96
Hitch
Cat.I
Cat.I
Cat.I
Tractor HP Requirement
20 - 65 HP
3 - 65 HP
30 - 65 HP
Maximum Additional weight
1000 lbs.
1000 lbs.
1000 lbs.
Weight
437 lbs.
539 lbs.
561 lbs.
Tractor 3-Point Lift Requirement
500 lbs.
600 lbs.
700 lbs.
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8" Heavy-duty frame with rack to hold additional weight
Pivot Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/4 Shaft with reinforcement structure
Spoons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4" OD Hardened closed spoons, 4-1/2" penetration
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . Greaseable journal bearings for each spoon assembly
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
GENERAL INFORMATION
The purpose of this manual is to assist you in
operating and maintaining your Core Aerator.
Read it carefully. It furnishes information and
instructions that will help you achieve years of
dependable performance. These instructions have
been compiled from extensive field experience
and engineering data. Some information may be
general in nature due to unknown and varying
operating conditions. However, through experience and these instructions, you should be able to
develop procedures suitable to your particular situation.
(Rev. 3/09/2010)
MAN0152 (Rev.11/17/2006)
The illustrations and data used in this manual
were current at the time of printing. However, due
to possible inline production changes, your
machine may vary slightly in detail. We reserve
the right to redesign and change the machines as
may be necessary without notification.
Throughout this manual, references are made to
right and left direction. These are determined by
standing behind the tractor facing the direction of
forward travel.
Introduction 3
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
TRAINING
 Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
 If you do not understand any part of this manual
and need assistance, see your dealer.
 Know your controls and how to stop engine and
attachment quickly in an emergency.
 Operators must be instructed in and be capable
of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
 Never allow children or untrained persons to
operate equipment.
PREPARATION
 Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
 Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
 Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
 A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
OPERATION
 Keep bystanders away from equipment.
 Do not operate or transport equipment while
under the influence of alcohol or drugs.
 Operate only in daylight or good artificial light.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
 Always comply with all state and local lighting
and marking requirements.
 Never allow riders on power unit or attachment.
 Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
 Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
 Look down and to the rear and make sure area
is clear before operating in reverse.
 Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
 Do not operate or transport on steep slopes.
 Make sure attachment is properly secured,
adjusted, and in good operating condition.
 Do not stop, start, or change directions suddenly on slopes.
 Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
 Use extreme care and reduce ground speed on
slopes and rough terrain.
4 Safety
PL48-72 Safety Rules (Rev. 11/17/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
 Watch for hidden hazards on the terrain during
operation.
STORAGE
 Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
 Keep children and bystanders away from storage area.
 Block equipment securely for storage.
MAINTENANCE
 Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key,
and unfasten seat belt.
 NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath implement.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
 Make sure attachment is properly secured,
adjusted, and in good operating condition.
 Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
 Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
 Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
 Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
PL48-72 Safety Rules (Rev. 11/17/2006)
Safety 5
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
3
1
4
1
CD5938A
2
1 - PN 1003751
5
2 - PN 55122
WARNING
WARNING
TO AVOID SERIOUS INJURY OR DEATH:
Read Operator's Manual before operating, servicing or
CRUSHING AND PINCHING HAZARD
Be extremely careful handling various parts of
the machine. They are heavy and hands, fingers,
feet, and other body parts could be crushed or
pinched between tractor and implement.
Operate tractor controls from tractor seat only.
Do not stand between tractor and implement
when tractor is in gear.
Make sure parking brake is engaged before
going between tractor and implement.
Stand clear of machine while in operation or
when it is being raised or lowered.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
1003751-A
6 Safety
repairing equipment. Follow all safety rules and
instructions. (Manuals are available from dealer or call
1-800-319-6637.)
Operate from tractor seat only.
Lower equipment to ground, stop engine, remove key
and set brake before dismounting tractor.
Never allow children or untrained persons to operate
equipment.
Never allow riders.
Keep bystanders away from equipment during operation.
Keep all shields in place and in good condition.
Do not transport towed or semi-mounted units over 20
mph.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN
RESULT IN INJURY OR DEATH.
55122-D
MAN0152 (Rev. 11/17/2006)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
3 - PN 55121
WARNING
FALLING OFF CAN RESULT IN BEING RUN OVER.
Tractor must be equipped with ROPS (or ROPS CAB) and
seat belt. Keep foldable ROPS systems in “locked up”
position at all times.
Buckle Up! Keep seat belt securely fastened.
Allow no riders.
RAISED IMPLEMENT CAN DROP AND CRUSH.
Never go underneath raised implement which can drop from
equipment or tractor 3-point hitch hydraulic leak down,
hydraulic system failures, movement of control levers or
mechanical linkage failures.
Service work does not require going underneath
implement. Read manual instructions.
FALLING OFF OR GOING UNDERNEATH IMPLEMENT
CAN RESULT IN SERIOUS INJURY OR DEATH. 55121--B
4 - PN 57500
WARNING
WHEN CONNECTING AND STORING EQUIPMENT
Follow all manual instructions and safety rules.
Properly connect to tractor before raising park stands or adding
ballast weight.
Remove ballast weight before disconnecting equipment from tractor.
Lower and properly secure all four park stands before
disconnecting equipment from tractor.
Park stands must be functional, kept in good repair, and stored on
unit.
Park and store on hard level ground away from people and children.
FAILURE TO FOLLOW INSTRUCTIONS CAN
RESULT IN INJURY OR DEATH.
5 - Serial Number Plate
57500
BE CAREFUL!
Use a clean, damp cloth to clean safety decals.
Avoid spraying too close to decals when using a pressure washer; high-pressure water can
enter through very small scratches or under edges of decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods dealer. To locate your
nearest dealer, check the Dealer Locator at www.woodsonline.com, or in the United States
and Canada call 1-800-319-6637.
MAN0152 (Rev. 11/17/2006)
Safety 7
OPERATION
The operator is responsible for the safe operation of
this aerator. The operator must be properly trained.
Operators should be familiar with the equipment, the
tractor, and all safety practices before starting operation. Read the safety rules and safety decals on pages
page 4 to page 7.
Recommended tractor ground speed is from 2 to 5
mph.
WARNING
 Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
 Never allow children or untrained persons to
operate equipment.
 Keep bystanders away from equipment.
 NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath implement.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
CAUTION
PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)
___ Review and follow all safety rules and safety
decal instructions on page 4 through page 7.
___ Check that equipment is properly and securely
attached to tractor.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Do not allow riders.
___ Check that all hardware is properly installed and
secured.
___ Check all lubrication points and grease as
instructed in “Service, lubrication information.”
___ Make sure tractor ROPS or ROPS CAB and seat
belt are in good condition. Keep seat belt
securely fastened during operation.
GENERAL INFORMATION
Core Aerator Operation
The Core Aerator is designed to reduce the soil compaction of an established turf area. The hardened
spoons attached to the reels penetrate and remove a
3/4 x 4-1/2” plug from the soil. Up to 1000 lbs of additional weight can be added to the frame to ensure the
proper penetration by the spoons.
The power for operating the aerator is developed
through the weight of the equipment and the contact
between the spoons and the turf. Know how to stop the
tractor and aerator quickly in an emergency. Survey the
area to be worked and remove any obstructions that
may affect the performance of the equipment.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
8 Operation
MAN0152 (Rev. 11/17/2006)
Tractor Stability
WARNING
 A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
4. Adjust the lower lift arm anti-sway device to
prevent the aerator from excessive side to side
movement.
NOTE: An optional Quick Hitch mounting kit is available. See page 16 for optional Quick Hitch parts list.
18
DP1
Figure 2. Lift Arms Attached to Aerator (Typical)
Figure 1. Tractor Stability
ATTACH CORE AERATOR TO TRACTOR
NOTE: The Core Aerator is designed for use on Category I, 3-point tractors. See page 3 for specifications.
1. Attach the tractor’s lower lift arms to the Core
Aerator and secure with mounting pins (18) and
klik pins. See Figure 2.
Top Link Pin
2. Attach the tractor’s top link to the upper mast of the
aerator. Secure with high-strength top link pin and
retaining pin provided with the tractor. See Figure
3.
3. Adjust top link as needed to level the aerator fore
and aft.
DP2
Figure 3. Top Link Attached to Aerator (Typical)

MAN0152 (Rev. 11/17/2006)
Operation 9
OWNER SERVICE
The information in this section is written for operators
who possess basic mechanical skills. If you need help,
your dealer has trained service technicians available.
For your protection, read and follow the safety information in this manual.
A
WARNING
 NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath implement.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
 Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
 Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key,
and unfasten seat belt.
DP3
Figure 4 . Lubrication Points
STORAGE
Refer to Figure 5 and Figure 6.
1. Raise aerator off the ground to provide necessary
clearance to adjust parking stands.
2. Remove pins (16) from the parking stand mounting
tube and lower stand to the storage position.
3. Reinstall pin.
4. Repeat for remaining three stands.
5. Lower aerator to the ground and disconnect from
tractor. Carefully drive tractor away from aerator
when disconnected.
CAUTION
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
16
LUBRICATION INFORMATION
1. Lubricate grease fittings (A, Figure 4), every 8
hours of operation.
2. Clean fittings prior to lubrication. Do not let
excessive grease build up around lubrication
points.
NOTE: One pump of a good grade multi-purpose
grease should be sufficient in most cases. Harsh or dry
conditions may require more frequent lubrication.
10 Owner Service
DP4
16.
33000 3/8 x 2-1/4 Lynch pin
Figure 5. Parking Stands Raised
MAN0152 (Rev. 11/17/2006)
1. Remove weights from top of aerator frame if
previously installed.
2. Remove water kit from shipping pallet, remove
parts from inside both tanks, unstrap tanks from
trays and remove bracket from trays.
3. Place two brackets (3) on top of right side of
aerator frame and two clamp bars (4) below frame.
4. Secure brackets and clamp bars together using
two cap screws (13), flat washers (11), and lock
nuts (12). Do not tighten hardware at this time.
DP5
Figure 6. Parking Stands Lowered into Storage
Position
INSTALL WATER WEIGHT TANK KIT
OPTIONAL
NOTE: Aerator frame should be between brackets
(3) and clamp bars (4).
5. Place water tank tray (2) over brackets and align
mounting holes. Secure using four cap screws
(10), flat washers (11), and lock nuts (12).
NOTE: Notch on tray should be towards the outside of the aerator frame. See Figure 8.
6. Repeat steps to install tank on left side of aerator.
7. Torque all hardware to 35 lbs-ft.
8. Place tanks (1) into trays with drain plugs in notch
of trays. Secure tanks into position using rubber tie
down straps.
9. Fill tanks with desires amount of water.
NOTE: Both tanks filled to capacity is approximately 430 lbs of additional weight. Make sure
tractor can handle additional weight. See Tractor
Stability, page 9 for additional front end weights.
1.
2.
3.
4.
10
11
12.
13
1011317
1011303
1011304
1011305
19887
565
B0618
31982
Tank, 26 gal
Water tank tray
Water tank bracket
Clamp bar
3/8 NC x 1 HHCS GR8
3/8 Flat washer
3/8 NC Stover lock nut
3/8 NC x 1-1/4 HHCS GR8
Figure 7. Water Tank Installation
MAN0152 (Rev. 11/17/2006
Figure 8. Water Tanks Installed
Owner Service 11
CLEANING
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
After Each Use
●
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
●
Inspect machine and replace worn or damaged
parts.
●
Inspect machine and replace worn or damaged
parts.
●
Replace any safety decals that are missing or not
readable.
●
Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
●
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.
●
Drain water from optional water weight kit to avoid
freezing and damage to the plastic tanks.
Periodically or Before Extended Storage
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Remove the remainder using a low-pressure water
spray.

12 Owner Service
MAN0152 (Rev. 11/17/2006)
DEALER CHECK LISTS
PRE-DELIVERY CHECK LIST
DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
(DEALER’S RESPONSIBILITY)
Assembly of this equipment is the responsibility of the
Woods dealer. It should be delivered to the owner completely assembled, lubricated, and adjusted for normal
operating conditions.
___ Show customer how to make adjustments.
Inspect the equipment thoroughly after assembly to
ensure it is set up properly before delivering it to the
customer.
The following check lists are a reminder of points to
inspect. Check off each item as it is found satisfactory
or after proper adjustment is made.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Properly attach implement to tractor and make
all necessary adjustments.
___ Check all bolts to be sure they are properly
torqued.
___ Check that all cotter pins and safety pins are
properly installed. Replace if damaged.
___ Point out the safety decals. Explain their meaning and the need to keep them in place and in
good condition. Emphasize the increased
safety hazards when instructions are not followed.
___ Present Operator's Manual and request that
customer and all operators read it before operating equipment. Point out the manual safety
rules, explain their meanings and emphasize
the increased safety hazards that exist when
safety rules are not followed.
___ For mounted units, add wheel weights, ballast
in front tires, and/or front tractor weight to
enhance front end stability. A minimum 20% of
tractor and equipment gross weight must be on
front tractor wheels. When adding weight to
attain 20% of tractor and equipment weight on
front tractor wheels, you must not exceed the
ROPS weight certification. Weigh the tractor
and equipment. Do not estimate!
___ Make customer aware of optional equipment
available so that customer can make proper
choices as required.

MAN0152 (Rev. 11/17/2006)
Dealer Check Lists 13
CORE AERATOR
21 - COMPLETE SAFETY DECAL SET
22 - COMPLETE DECAL SET
14 Parts
MAN0152 (Rev. 11/17/2006)
CORE AERATOR PARTS LIST
REF
1
PART
DESCRIPTION
REF
PART
QTY
DESCRIPTION
1
Sleeve, .81 x 1.12 x 2
12
54893
8
2
2371 *
1
3/4 NC Lock nut
12
54893
12 1.25 SAE Flat washer (PL60 & 72)
3
31207 *
1
3/4 NC 4 HHCS GR5
13
P23
8
4
2522 *
2
3/4 Lock washer
13
P23
12 Spoon plate (PL60 & 72)
5
1002018
QTY
Spoon plate (PL48)
2
3/4 NC x 2 HHCS GR5
14
P1372
2
1.62 Spacer
6
71635
3
3/8 NC Stop nut (PL48)
15
P19
4
Parking Stand
6
71635
5
3/8 NC Stop nut (PL60 & 72)
16
33000 *
4
3/8 x 2-1/4 Lynch Pin
976 *
3
3/8 NC x 1 HHCS GR5 (PL48)
17
D2213
4
Bushing
976 *
5
3/8 NC x 1 HHCS GR5 (PL60 & 72)
7
7
735 *
1.25 SAE Flat washer (PL48)
18
SU105
2
Cat 1 Pin w/klik pin
8
FA511 * 128 5/16 NC x 2 HHCS (PL48)
19
P22
4
Roller head (PL48)
8
FA511 * 192 5/16 NC x 2 HHCS (PL60 & 72)
19
P22
6
Roller head (PL60 & 72)
9
FA220
128 5/16 NC Nylock nut (PL48)
20
P1448
1
53.62 Axle shaft (PL48)
9
FA220
192 5/16 NC Nylock nut (PL60 & 72)
20
P1460
1
65.62 Axle shaft (PL60)
10
P52
64 Plugger spoon (PL48)
20
P1472
1
77.62 Axle shaft (PL72)
10
P52
96 Plugger spoon (PL60 & 72)
21
54466
1
Complete safety decal set
11
1002966
3
Spacer (PL48)
22
1002965
1
Complete decal set
11
1002971
5
Spacer (PL60)
11
1002974
5
Spacer (PL72)
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
MAN0152 (Rev. 11/17/2006)
Parts 15
OPTIONAL QUICK HITCH KIT
REF
PART
QTY
1
…………
1
Frame
2
Quick Hitch sleeve
2
1001702
DESCRIPTION
1011306 WATER WEIGHT KIT (OPTIONAL)
REF
PART
QTY
DESCRIPTION
1
1011317
2
Tank, 26 gal
2
1011303
2
Water tank tray
3
1011304
4
Water tank bracket
4
1011305
4
Clamp Bar
8
3/8 NC x 1 HHCS GR8
10
11
19887 *
565 * 16 3/8 Flat washer
12
B0618
16 3/8 NC Stover lock nut
13
31982 *
8
3/8 NC x 1-1/4 HHCS GR8
14
M0024 *
4
Strap, tie down 3/8 x 3’ (not shown)
15
1037381 1
8” Lid and Ring
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
16 Parts
(Rev. 6/4/2014)
MAN0152 (Rev. 11/17/2006)
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
1/4"
5/16"
7/16"
1/2"
6
12
8
17
10
19
13
26
14
27
18
37
3/8"
7/16"
9/16"
5/8"
23
36
31
48
35
55
47
75
49
78
67
106
1/2"
9/16"
3/4"
13/16"
55
78
75
106
85
121
115
164
120
171
163
232
5/8"
3/4"
15/16"
1-1/8"
110
192
149
261
170
297
230
403
240
420
325
569
7/8"
1"
1-5/16"
1-1/2"
306
467
416
634
474
722
642
979
669
1020
907
1383
A
METRIC SERIES
TORQUE
CHART
A
Metric Bolt Head
Identification
8.8
Metric
Grade 8.8
10.9
Metric
Grade 10.9
Coarse Thread
Fine Thread
Marking on Head
Marking on Head
A
Diameter &
Thread Pitch
(Millimeters)
Wrench
Size
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
Diameter &
Thread Pitch
(Millimeters)
6 x 1.0
10 mm
8
6
11
8
8
6
11
8
6 x 1.0
8 x 1.25
10 x 1.5
13 mm
16 mm
20
39
15
29
27
54
20
40
21
41
16
30
29
57
22
42
8 x 1.0
10 x 1.25
12 x 1.75
14 x 2.0
18 mm
21 mm
68
109
50
80
94
151
70
111
75
118
55
87
103
163
76
120
12 x 1.25
14 x 1.5
16 x 2.0
18 x 2.5
24 mm
27 mm
169
234
125
172
234
323
173
239
181
263
133
194
250
363
184
268
16 x 1.5
18 x 1.5
20 x 2.5
22 x 2.5
30 mm
34 mm
330
451
244
332
457
623
337
460
367
495
270
365
507
684
374
505
20 x 1.5
22 x 1.5
24 x 3.0
30 x 3.0
36 mm
46 mm
571
1175
421
867
790
1626
583
1199
623
1258
459
928
861
1740
635
1283
24 x 2.0
30 x 2.0
Typical Washer
Installations
Bolt
Metric 8.8
Lock Washer
Metric 10.9
Metric 8.8
Metric 10.9
Flat Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 17
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
IN
MM
5/8
3/4
7/8
1
2
3
4
5
6
7
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM
10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
ASABE ....................American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE....... American Society of Agricultural Engineers
ATF................................Automatic Transmission Fluid
BSPP............................. British Standard Pipe Parallel
BSPTM ................ British Standard Pipe Tapered Male
CV .................................................... Constant Velocity
CCW.............................................. Counter-Clockwise
CW .............................................................. Clockwise
F .......................................................................Female
FT .............................................................. Full Thread
GA ..................................................................... Gauge
GR (5, etc.)........................................... Grade (5, etc.)
HHCS ........................................ Hex Head Cap Screw
HT ...........................................................Heat-Treated
JIC ................. Joint Industry Council 37° Degree Flare
LH................................................................. Left Hand
LT ...........................................................................Left
m ........................................................................ Meter
mm ............................................................... Millimeter
M .......................................................................... Male
18 Appendix
MPa ........................................................ Mega Pascal
N ...................................................................... Newton
NC...................................................... National Coarse
NF ........................................................... National Fine
NPSM .................... National Pipe Straight Mechanical
NPT...........................................National Pipe Tapered
NPT SWF......... National Pipe Tapered Swivel Female
ORBM ...........................................O-Ring Boss - Male
P .......................................................................... Pitch
PBY.......................................................Power-Beyond
psi ......................................... Pounds per Square Inch
PTO......................................................Power Take Off
QD ................................................... Quick Disconnect
RH.............................................................. Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................ Revolutions Per Minute
RT ........................................................................Right
SAE.......................... Society of Automotive Engineers
UNC ..................................................... Unified Coarse
UNF .......................................................... Unified Fine
UNS ..................................................... Unified Special
Bolt Torque & Size Charts (Rev. 3/28/2007)
WARRANTY
All Models Except Mow’n MachineTM Zero-Turn Mowers
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
From (Dealer): __________________________________________
Model Number: ____________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Model Number
Duration (from date of
delivery to the original
purchaser)
All units invoiced after 4/30/2012
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,
DS1260, DSO1260, DS1440, TS1680,
BW12, BW15LH, BW126X, BW180X, BW126XHD, BW180XHD, BW1260X, BW1800X,
Gearbox
components
Blade
spindles
Rust-through
BW240X, BW240XHD, BW1620X, BW2400X
6 years
DS96, DS120, RCC42, RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD,
S27CD, S30CD, TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204, TSG50, S12ED, S15ED,
S18ED, S20ED, TPD25, TPD35, TPD65, TPD95
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44, HC48, HC54, HC60, HC72, RC3.5,
RC4, RC5, RC6
3 years (1 year if used in rental or
commercial applications)
RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204
3 years
BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X, BW126X, BW180X, BW126XHD,
BW180XHD, BW1260X, BW1800X, BW240, BW240HD, DS1260, DSO1260, DS1440, TS1680
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other
than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or
rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regarding
warranty service and locations may be obtained by contacting:
Woods Equipment
A Blount International Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
woodsequipment.com
F-3079 (Rev. 1/8/2014)
WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser
with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty
does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or
otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any
way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this
Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after
such defect or noncompliance is discovered or should have been discovered, routed through the dealer and
distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete
such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO
OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS
WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly
or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty,
negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing,
Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of
crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain
materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including
without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify,
or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
A Blount International Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
woodsequipment.com
©2014 Woods Equipment Company. All rights reserved. Woods® and the Woods logo are trademarks of Woods Equipment Company. All other
trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective
companies or mark holders. Specifications subject to change without notice.
F-8494 (Rev. 1/10/2014)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement