Advertisement
Advertisement
PROFESSIONAL
SERIES
Security and Remote Start Installation Guide for models:
ca6153
2012 Audiovox Electronics Corporation. All rights reserved.
1
2
Table of Contents
Before You Begin ...................................................................................... 4
Wire Connection Guide ........................................................................... 5
4 Pin Main Harness ................................................................................... 7
6 Pin Start Harness ................................................................................... 8
6 Pin Output Harness ............................................................................. 10
8 Pin Input Harness ................................................................................. 11
4 Pin Alternate Output Harness ............................................................. 14
3 Pin Door Lock Output Harness ........................................................... 15
Additional Ports ...................................................................................... 19
Antenna / LED / Programming Port ....................................................... 19
DBI Port .................................................................................................... 19
Telematic Interface Port .......................................................................... 19
Set Up & Programming .......................................................................... 20
Transmitter Programming ........................................................................ 20
Manual Feature Programming ................................................................. 20
Programming Feature Banks .................................................................. 21
Tach Programming .................................................................................. 24
Smart Tachless Mode ............................................................................. 24
Adjusting the Shock Sensor .................................................................. 25
Testing the Shock Sensor ...................................................................... 25
Chirp Delete - User Accessible .............................................................. 25
Dome Light Delay / Theater Dimming ..................................................... 25 ca6153 revA
Feature Descriptions ............................................................................. 26
Transmitter Button Functions ............................................................. 32
Security Trigger Zones ......................................................................... 33
Remote Start Shutdown Diagnostics ................................................ 33
System Layout ......................................................................................... 34
2012 Audiovox Electronics Corporation. All rights reserved.
3
4
BEFORE YOU BEGIN
FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle during installation
Avoid mounting components or routing wires near hot surfaces
Avoid mounting components or routing wires near moving parts
Tape or loom wires under hood for protection and appearance
Use grommets when routing wires through metal surfaces
Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers.
Technical Support (800) 421-3209 or go to http://techservices.codesystems.com
ca6153 revA
4 Pin Main Harness
3
4
1
2
WHITE/RED
WHITE
BLACK
BROWN
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
GROUND
SIREN OUTPUT ( + )
6 Pin Start Harness
4
5
6
1
2
3
PURPLE
RED
ORANGE
PINK/WHITE
RED/WHITE
PINK
STARTER OUTPUT - MOTOR SIDE
BATTERY 12V ( + )
ACCESSORY 1 ( + )
IGNITION 2 ( + )
BATTERY 12V ( + )
IGNITION 1 ( + )
6 Pin Output Harness
4
5
6
1
2
3
BROWN/BLACK
BLUE/BLACK
VIOLET/BLACK
RED/WHITE
LT GREEN/BLACK
ORANGE
HORN OUTPUT ( - )
START STATUS / ACTIVE OUTPUT ( - )
AUX 1 OUTPUT ( - )
TRUNK RELEASE OUTPUT ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
GROUND WHEN ARMED OUTPUT ( - )
2012 Audiovox Electronics Corporation. All rights reserved.
5
6
8 Pin Input Harness
4 Pin Alternate Output Harness
3
4
1
2
BLACK/YELLOW
GREEN/WHITE
LT BLUE
LT GREEN/BLACK
PULSE DURING CRANK ( - )
PULSE AFTER SHUTDOWN ( - )
FACTORY ARM / PULSE AFTER START ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
3 Pin Lock Output Harness
1
2
3
BLUE
OPEN
GREEN
UNLOCK ( - )
LOCK ( - ) ca6153 revA
4 Pin Main Harness
WHITE/RED PARKING LIGHT INPUT 1
2 WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights are turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
3 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
4 BROWN SIREN OUTPUT ( + )
Locate a suitable mounting location in the engine compartment for the siren, away from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
2012 Audiovox Electronics Corporation. All rights reserved.
7
8
6 Pin Start Harness
PURPLE STARTER OUTPUT ( + ) 1
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned to the
START position. Cut the vehicle's starter wire in half when installing the starter kill relay.
Verification after starter wire is cut:
KEY SIDE of starter wire registers voltage when the key is turned to the
START position.
MOTOR SIDE of starter wire registers no voltage.
Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle starter wire when installing the starter kill relay.
2 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3 ORANGE ACCESSORY 1 ( + )
Locate the vehicle’s accessory wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the key is turned to the START (or CRANK) position.
Connect the ORANGE wire to the vehicle’s accessory wire.
ca6153 revA
4 PINK/WHITE IGNITION 2 ( + )
Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.
Programmable output: IGN, ACC, Start.
5 RED/WHITE BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6 PINK IGNITION 1 ( + )
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
2012 Audiovox Electronics Corporation. All rights reserved.
9
10
6 Pin Output Harness
BROWN/BLACK HORN OUTPUT ( - ) 1
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 200mA.
2 BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
This wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. If this wire will be used for multiple application's a 1 amp diode is required in-line with the stripe facing the control module.
3 VIOLET/BLACK AUX 1
This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.
4 RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when the trunk release is activated.
This is a low current 200mA output and in configurable in option programming.
ca6153 revA
5 LT GREEN/BLACK FACTORY DISARM /
PULSE BEFORE START ( - )
This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder.
Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.
6 ORANGE GROUND WHEN ARMED OUTPUT ( - )
This wire will have a continuous ( - ) 200mA output when the system is Armed. This wire is typically used for controlling the starter interrupt relay as well as window modules or additional sensors.
This output can be configured in option programming.
8 Pin Input Harness
1 BLUE/WHITE INSTANT TRIGGER INPUT ( - )
This wire is a GROUND input for an external sensor or secondary pin switch.
Verification: This wire when connected will trigger the security system.
2 GREEN DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This wire will register positive voltage when the door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide.
2012 Audiovox Electronics Corporation. All rights reserved.
11
12
3 PURPLE DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or "0" Volts when the door is closed and the interior light is off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide.
4 WHITE/BLUE EXTERNAL START INPUT ( - )
This wire will activate the Remote Start function when a GROUND pulse is applied to it from an external device.
5 GRAY HOOD PIN INPUT ( - )
Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.
Verification: This wire when connected will register ground when the vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
6 BLACK/WHITE NEUTRAL SAFETY INPUT ( - )
Locate the vehicle’s neutral safety circuit.
Verification: This wire registers ( - ) voltage when the vehicle’s gear selector is in park or neutral.
Connect the BLACK/WHITE neutral safety input wire to the neutral safety wire of the vehicle or an optional toggle switch. The remote start feature will not operate unless this input is supplied with a ground source.
ca6153 revA
7 BROWN/RED BRAKE INPUT ( + )
Locate the vehicle’s brake light wire at the brake pedal mounted switch. This connection is required for remote start.
Verification: This wire registers positive voltage when the brake pedal is pressed.
Connect the BROWN/RED wire to the vehicle’s brake light wire.
8 PURPLE/WHITE TACH INPUT
Locate the vehicle’s ignition coil or fuel injector in the engine compartment.
Verification: Test using the following procedure:
1.
2.
3.
4.
5.
Set voltmeter to AC VOLTS.
Attach positive lead of a volt meter to a constant 12 volt source.
Attach negative lead of a volt meter to the wire to be tested.
Start the engine.
Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading will increase as the engine’s RPM increases.
Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or fuel injector.
2012 Audiovox Electronics Corporation. All rights reserved.
13
14
4 Pin Alternate Output Harness
1 LT GREEN/BLACK FACTORY DISARM /
PULSE BEFORE START ( - )
This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder.
This output can be configured in option programming.
2 LT BLUE FACTORY ARM /
PULSE AFTER START ( - )
This wire will supply a ( - ) 200mA pulse both upon arming the system and upon successful completion of the remote start activation sequence and is typically used to re-lock the vehicle’s doors upon remote start if necessary.
This output can be configured in option programming.
3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown.
This output can be configured in option programming.
4 BLACK/YELLOW PULSE DURING CRANK ( - )
Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)
Verification: This wire registers voltage only in the start (crank) position of the ignition switch.
This output can be configured in option programming.
ca6153 revA
3 Pin Lock Output Harness
1
3
BLUE
GREEN
UNLOCK ( - )
LOCK ( - )
The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams.
Negative Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register ground when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Negative Locks:
GREEN (-) Lock Output
Lock
Unlock
Vehicle Door Lock
Control Relays
BLUE (-) Unlock Output
2012 Audiovox Electronics Corporation. All rights reserved.
15
Positive Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register positive voltage when the Lock and
Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Positive Locks:
Fused +12 Volt
Battery Souce
86
87
87a
30
85
GREEN (-) Lock Output
Lock
Unlock
Vehicle Door Lock
Control Relays
Fused +12 Volt
Battery Souce
86
87
87a
30
85 BLUE (-) Unlock Output
Reverse Polarity Locks (5-Wire Door locks)
16
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Reverse Polarity Locks:
Fused +12 Volt
Battery Souce
Lock
Unlock
86
87
87a
30
X
Cut
85
GREEN (-) Lock Output
To Door Lock Motor
Fused +12 Volt
Battery Souce
86
87
87a
30
X
Cut
85 BLUE (-) Unlock Output
To Door Lock Motor ca6153 revA
Negative Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable ground when the switch is activated.
Please consult the wire and location chart for specific resistor values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Multiplex Locks:
GREEN (-) Lock Output
Lock
Unlock
86
87
87a
30
85
Ground
Fused +12 Volt
Battery Source
Resistor
86
87
87a
30
85
BLUE (-) Unlock Output
Vehicle Door Lock
Control Relays
Positive Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Multiplex Locks:
GREEN (-) Lock Output
Lock
Unlock
86
87
87a
30
85
Fused +12 Volt
Battery Source
Resistor
86
87
87a
30
85
BLUE (-) Unlock Output
Vehicle Door Lock
Control Relays
2012 Audiovox Electronics Corporation. All rights reserved.
17
18
Adding Aftermarket Actuators
After installing aftermarket actuators, (not supplied). Connect the GREEN and
BLUE wires shown in the diagram below using (2) SPDT relays (not supplied).
Door Lock
Actuator
M
87
86
30
87a
85
Fused +12 Volt
Battery Source
Chassis
Ground
GREEN (-) Lock Output
87
86
30
87a
85
Fused +12 Volt
Battery Source
Chassis
Ground
BLUE (-) Unlock Output ca6153 revA
Additional Ports
Antenna / LED / Programming Port
Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/ receiver cable to the control module and plug into the antenna port.
Data Bus Interface Port
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus
Interfaces to communicate with the vehicle's Databus. When using the DBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available. Please refer to the D2D (Data to Data) function list available per vehicle on the tech service web site.
Tach Input
Door Trigger
Door Lock Control
Brake Safety Shut Down
Trunk/Hatch Open
Passlock / Passkey Interface (GM Only)
Dome Light Supervision Transponder Interface Activation
Factory Alarm Arm / Disarm Diesel Glow Plug Input
Manual Arm / Disarm Inputs (factory keyless controls system)
Telematic Interface Port
This 4 pin port is used for telematic Interface accessories, such as the CarLink
ASCL1, which can control some of the following features.
Door Lock Control
Sliding Doors
Car Find
Trunk Release
AUX Output
Remote Start
2012 Audiovox Electronics Corporation. All rights reserved.
19
Set Up & Programming
Transmitter Programming - Feature Bank 1
1.
2.
3.
4.
5.
6.
Turn the ignition ON.
Press and hold the valet/override button.
Within 10 seconds the system will chirp (3) three times.
Press 1 button of each transmitter you wish to program.
The system will respond with 1 chirp for each accepted transmitter.
Pressing the override button at anytime during programming will advance to the next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th transmitter will erase the oldest transmitter in memory.
NOTE: This system has PTN - Programmed Transmitter Notification. Each time the ignition is turned ON, the LED will flash the number of transmitters programmed to the system.
Transmitter programming for 2 Car Mode *2 way system only:
1.
Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the owners manual for 2 car operation)
2.
Follow the steps above for transmitter programming.
NOTE: 2 car mode requires an additional security system installed in a second vehicle.
Manual Feature Programming - Feature Bank 2 - 5
20
5.
6.
1.
2.
3.
4.
Turn the ignition ON.
Press and hold the valet/override button.
Within 10 seconds the system will chirp (3) three times.
Use the valet/override button to advance through each option bank. For feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4) four, (5) five, (6) six and (7) seven chirps.
Use the transmitter button to scroll through the selections in each feature bank, the system will chirp to match the feature number.
Press the transmitter button to change the desired feature. The LED will flash indicating the changed feature.
ca6153 revA
Defaulting All Features: Pressing the button anytime while in any of the feature banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.
Feature Bank 1 - 3 Chirps
Transmitter Programming
Refer to transmitter programming.
Feature Bank 2 - 4 Chirps
Security Control
1 Silent Choice
2 Passive Locks
1 LED Flash
ON
Active
2 LED Flash
OFF
Passive
3 LED Flash
3 Passive Arming
4 Siren / Horn - Arm/Disarm Chirps
5 Siren Duration
6 Security
Active Passive
Siren / Horn Siren
30 Seconds 60 Seconds
ON OFF
7 Anti-Hijack Mode
8 Orange - Ground w/ Armed Output
9 DBI Port Protocol
OFF ON
Ground While
Armed
Ground While
Disarmed
DBI Protocol ADS Protocol
10
Arm/Disarm
Chirp / Parking Light Pattern
Standard:
2 - Arm
1 - Disarm
Inverted:
1 - Arm
2 - Disarm
Horn
4 LED Flash 5 LED Flash 6 LED Flash
2012 Audiovox Electronics Corporation. All rights reserved.
21
22
Feature Bank 3 - 5 Chirps
Output Control
1 Extended Lock Pulse
2
Factory Disarm
Lt Green / Black
3 Ignition Controlled Locks
4
Trunk Output Timing
Red / White Output
5 Horn Output Timing
6 Real Panic
7
AUX 1
Violet / Black Output
1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1 Second 3.5 Seconds
1 Second
Lock, Double
Pulse Unlock
30 Second
Lock, Double
Pulse Unlock
Double Pulse
Lock, 1
Second Unlock
Factory
Disarm
OFF
1 Second
Pulse
16mS
ON
2nd Unlock
Factory Disarm
/ Start Status
Lock and
Unlock
Lock Only
10 Seconds
10mS
20 Seconds
30mS
Unlock Only
Latched until
IGN ON
Latched ON until Button
Press
40mS 50mS
OFF
Push and
Hold
Latched
Latched until
IGN ON
Dome Light
Output
Defrost Output
Single Pulse
Defrost Output
Latched 5 Min
Feature Bank 4 - 6 Chirps
Remote Start Control
1 RF Start Chirp
2 Run Time
3 Running Lights
4 Tach Mode
5 Voltage Level
6 Crank Time
7 Crank Averaging / Crank Time
8 Gas / Diesel
9 Single / Double Press Start
10 IGN 2 Output
11 2 or 3 Hour Start
12 Turbo Timer
1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
ON
15 Minutes
OFF
5 Minutes 10 Minutes 20 Minutes 45 Minutes
Steady
Tach
Flashing
Tachless
(Crank Average
Hybrid (Crank
Average / NO
/ Voltage) Voltage)
DBI Port
Low High
1.0 Seconds 0.8 Seconds 1.5 Seconds 2.0 Seconds 4.0 Seconds
Averaging Preset Time
60 Minutes
Gas
10 Second
Delay
15 Second
Delay
20 Second
Delay
45 Second
Delay
Double Press Single Press
Ignition 2
3 Hour
OFF
Accessory
2 Hour
1 Minute
Start / Crank
3 Minute 5 Minute ca6153 revA
Feature Bank 5 - 7 Chirps
4 Pin Alternate Output Control
1 Lt Green / Black Output
2 Lt Blue Output
3 Green / White Output
4 Black / Yellow Output
1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
Pulse Before
Start / During
Unlock
Ground While
Running
Ignition
Pulse After
Start / During
Lock
Ground While
Running
Ignition
Accessory
Accessory
Pulse During
Crank
Pulse During
Crank
Pulse After
Shutdown
Ground While
Running
Ignition Accessory
Pulse During
Crank
Pulse During
Crank
Ground While
Running
Ignition Accessory
2012 Audiovox Electronics Corporation. All rights reserved.
23
Tach Programming
The unit will not operate unless tach is programmed or tachless option is
turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or single injector. To learn tach:
1.
Turn the ignition key to the ON position.
2.
Press and release the valet/override button 3 times.
3.
Immediately turn the ignition key OFF.
4.
Press and hold the valet/override button, then start the vehicle using the key.
5.
When the unit senses the tach signal, the parking lights will begin to flash.
6.
Allow the vehicle to settle to a normal idle speed.
7.
Release the valet/program push-button switch. The parking lights will turn on for 2 seconds and 1 long chip will indicate that the learned tach signal is stored and the unit has exited tach learn mode.
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a poor tach source, the parking lights will not flash. To correct this situation, locate and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine.
24
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the system and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode.
1.
Activate the remote start. The parking lights should begin flashing 7 times indicating no tach signal has been learned.
2.
Within the 7 flash time period, press and hold the button.
3.
The system will chirp 1 time indicating the system is now in tachless mode.
ca6153 revA
Adjusting the Shock Sensor
1.
2.
Increase sensitivity by turning the adjustment dial clockwise.
Decrease sensitivity by turning the adjustment dial counter clockwise.
Testing the Shock Sensor
Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.
1.
Turn the ignition ON then OFF.
2.
Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming.
1.
Close all doors with ignition off.
2.
Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE.
3.
Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the learning mode.
4.
The LED will begin to flash indicating the system has exited the learning mode and is now armed.
2012 Audiovox Electronics Corporation. All rights reserved.
25
Feature Descriptions
Feature Bank 2 - Security
1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.
ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons.
OFF - normal arm/disarm chirps upon the first press of lock/unlock.
2 - Passive Locks: Determines manual or automatic locking of the vehicle’s doors.
Active - Requires use of the transmitter to lock the vehicle’s doors.
Passive - Automatically locks the vehicle’s doors 1 minute after the last door is closed
3 - Passive Arming: Determines manual or automatic locking of the vehicle’s doors.
Active - Requires use of the transmitter to arm the security system.
Passive - Automatically arms the security system 1 minute after the last door is closed
4 - Siren / Horn: This feature selects which output(s) will sound the system’s arm/disarm chirps. This feature does not effect the triggered state of the security system and during a triggered cycle, both the siren and horn outputs will activate respectively.
5 - Siren Duration: This feature controls the length of time the system will sound when triggered.
6 - Security: Controls security functionality - ON / OFF.
ON - Full security functionality.
OFF - The security system does not trigger. Panic, Remote Start and all other convenience features operate as normal.
26
7- Anti-Hijack Mode: Controls car jack mode - ON / OFF.
OFF - Standard security system operation.
ON - Enables Car Jack mode functionality as described in the owners manual ca6153 revA
8 - Ground While Armed / Orange Output: Controls the output of the orange wire. This wire will either supply a ( - ) output when armed OR disarmed.
9 - DBI Port Protocol: Determines the protocol type in which the DBI port uses to interface with external modules.
DBI Protocol
ADS Protocol
10 - Arm/Disarm Chirp / Parking Light Pattern: Determines the number of chirps and parking light flashes when the system is armed/disarmed.
Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm.
Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm.
Feature Bank 3 - Output Control
1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock output wires.
1 Second - Single 1 second lock pulse, single 1 second unlock pulse.
3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.
1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1 second unlock pulse.
30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double
1 second unlock pulse.
Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1 second unlock pulse.
2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm wire on the 6 pin output harness only and does not change the output of the factory disarm wire on the 4 pin alternate output harness.
Factory Disarm - Single 1 second pulse with unlock and remote start activation.
2nd Unlock - Same output as unlock with 2nd press of unlock.
Factory Disarm / Start Status - Single 1 second pulse with unlock and continuous ( - ) output during the remote start cycle.
2012 Audiovox Electronics Corporation. All rights reserved.
27
28
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled
ON or OFF.
OFF - Door locks not activated by ignition.
Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off.
Lock Only - Doors lock when ignition is turned on.
Unlock Only - Doors unlock when ignition is turned off.
4 - Trunk Output Timing - Red/White Output: Controls the output timing/type of the RED/WHITE output.
1 Second Pulse - 1 second pulse output.
10 Second - Continuous output for 10 seconds.
20 Seconds - Continuous output for 20 seconds.
Latched until IGN ON - Continuous output until the vehicle’s ignition is turned
ON.
Latched ON until Button Press - Continuous output until the activation button is pressed again.
5 - Horn Output Timing: Control the minimum horn pulse time in milli seconds, some vehicle will require a longer pulse to activate the factory horn.
16mS 10mS 30mS 40mS 50mS
6 - Real Panic: Controls the panic out when triggered from the transmitter.
ON - Randomized horn honks when panic is triggered.
OFF - Standard pattern horn honks when panic is triggered.
7 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
Dome Light Output - Output used for illuminated entry and is not controlled by the AUX 1 function of the transmitter.
Defrost Output Single Pulse - Single 1 second pulse after start
Defrost Output Latched 5 Minutes - 5 minute continuous output after remote start.
ca6153 revA
Feature Bank 4 - Remote Start Control
1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF.
2 - Run Time: Controls the time in minutes that the vehicle will stay running under control of the remote start until the system times out. The system may also be shut down at any time by use of the transmitter or system shutdowns.
3 - Running Lights: Controls the WHITE parking light output wire during remote start.
Steady - Parking lights constant during the remote start cycle.
Flashing - Parking lights flash at a slow pace during the remote start cycle.
4 - Tach Mode: Determines how the system monitors the engine running during remote start.
Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage.
Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start.
Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key.
DBI Port - Monitors the vehicle’s tach rate through an interface module connected to the DBI port.
5 - Voltage Level: The voltage variance for remote start when set to tachless.
(see tach mode)
HIGH - The variance in battery voltage from before the remote start is activated to after the engine is running must be greater than 0.5 volts.
LOW - The variance in battery voltage from before the remote start is activated to after the engine is running may be less than 0.5 volts.
6 - Crank Time: Preset output times for the PURPLE starter wire.
7 - Crank Average / Crank Time: The length of time in which the remote start will crank the vehicle’s starter.
Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the key.
Preset Time - Preset starter output time. (see crank time)
2012 Audiovox Electronics Corporation. All rights reserved.
29
30
8 - Gas / Diesel: Selects engine type and delay time for the starter output wire during remote start activation.
Gas - Gasoline engine, no delay for the starter output wire.
10 Second Delay - Diesel engine, delays the starter output wire for 10 seconds after the ignition has been powered up by the remote start.
15 Second Delay - Diesel engine, delays the starter output wire for 15 seconds after the ignition has been powered up by the remote start.
20 Second Delay - Diesel engine, delays the starter output wire for 20 seconds after the ignition has been powered up by the remote start.
45 Second Delay - Diesel engine, delays the starter output wire for 45 seconds after the ignition has been powered up by the remote start.
9 - Single / Double Pulse Start: Switches the remote start activation between a single or double press from the transmitter.
10 - IGN 2 Output: Programmable high current output.
Ignition 2 - Output becomes active with the same timing as the ignition output and does not drop out during crank.
Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.
Start / Crank - Output becomes active with the same timing as the starter output wire, during crank only.
11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours.
12 - Turbo Timer: When activated, the vehicle will run for the programmed time.
OFF 1 Minute 3 Minutes 5 Minutes ca6153 revA
Feature Bank 5 - 4 Pin Alternate Output Control
1 - Lt Green/Black Output : Controls the LT GREEN/BLACK output activation type and timing.
Pulse before Start / During Unlock - 1 second pulse when remote start is activated. Also a 1 second pulse when unlock is pressed.
Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.
Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.
Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.
Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.
2 - Lt Blue Output : Controls the LT BLUE output activation type and timing.
Pulse After Start / During Lock - 1 second pulse after the remote start sequence and has confirmed the vehicle is running. Also a 1 second pulse when unlock is pressed.
Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.
Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.
Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.
Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.
3 - Green/White Output : Controls the GREEN/WHITE output activation type and timing.
Pulse After Shutdown - 1 second pulse after the remote start has shutdown.
Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.
Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.
Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.
Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.
2012 Audiovox Electronics Corporation. All rights reserved.
31
32
4 - Black/Yellow Output : Controls the BLACK/YELLOW output activation type and timing.
Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.
Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.
Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.
Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.
Transmitter Button Functions
1 Way
Transmitter
Lock Unlock
Panic
Lock X
Unlock X
2 Step Unlock X
X Trunk
Car Finder X
X Panic
Remote Start
Remote Start
Shutdown
Run Time
Extention
AUX 1
Shock Bypass
X
X
X
X
Hidden Alarm
Passive Arming
Bypass
Turbo Timer
2 / 3 Hour Start
Daily Start Timer
X
X
X
X
X
X
X
X
X
X
X
X
Press and Release
Press and Release
Press and Release 2 times
Push and Hold (3 Sec)
Press and Release
Push and Hold (3 Sec)
Press and Release (1 or 2 times depending on selectable option)
Push and Hold (3 Sec)
Press and Release 4 times.
Push and Hold (3 Sec)
Press and Release Lock then
Press Lock + Car Find
Press and Release Car Fnd then
Press Lock
Press and Release
Press Unlock + Start
Ignition ON/OFF, Press and Hold
Valet Button, Press Start 4 times
Press Lock + Start ca6153 revA
Security Trigger Zones
If the security system has been triggered the LED will flash one of the patterns below indicating the zone.
LED FLASHES TRIGGER ZONE
2 Flashes
3 Flashes
4 Flashes
5 Flashes
Hood / Trunk Input
Door Input
Shock Sensor
Ignition Input
Remote Start Shutdown Diagnostics
If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.
To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button.
LED FLASHES
3 Flashes
4 Flashes
5 Flashes
7 Flashes
SHUTDOWN ZONE
Hood Input
Brake Input
Neutral Safety Input
Remote Start Valet Mode
Manual Transmission Mode not set (manual transmission models only)
Tach not learned / Crank Average not learned
2012 Audiovox Electronics Corporation. All rights reserved.
33
34
BLUE/WHITE
GREEN
PURPLE
WHITE/BLUE
GRAY
BLACK/WHITE
INSTANT TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( + )
EXTERNAL START INPUT ( - )
HOOD INPUT ( - )
NEUTRAL SAFETY INPUT ( - )
BROWN/RED BRAKE INPUT ( + )
INPUT
SHOCK SENSOR PORT
TELEMATIC PORT
ANTENNA
LED
VALET
PURPLE
RED
ORANGE
PINK/WHITE
RED/WHITE
PINK
STARTER OUTPUT - MOTOR SIDE ( + )
BATTERY 12V ( + )
ACCESSORY 1 ( + )
IGNITION 2 ( + )
BATTERY 12V ( + )
IGNITION 1 ( + )
WHITE/RED
WHITE
BROWN
BLACK
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
GROUND
SIREN OUTPUT ( + )
BLACK/YELLOW
GREEN/WHITE
LT BLUE
LT GREEN/BLACK
PULSE DURING CRANK ( - )
PULSE AFTER SHUTDOWN ( - )
FACTORY ARM / PULSE AFTER START ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
BROWN/BLACK
BLUE/BLACK
VIOLET/BLACK
RED/WHITE
LT GREEN/BLACK
ORANGE
BLUE
OPEN
GREEN
DBI PORT
HORN OUTPUT ( - )
START STATUS / ACTIVE OUTPUT ( - )
AUX 1 OUTPUT ( - )
TRUNK RELEASE OUTPUT ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
GROUND WHEN ARMED ( - )
UNLOCK ( - )
LOCK ( - )
86
87
87a
30
85
ORANGE
RED
BLACK
WHITE / BLACK
OPEN
STARTER INTERUPT RELAY
86 - ARMED OUTPUT ( - )
85 - IGNITION ( + )
87A - STARTER OUTPUT - MOTOR SIDE
30 - STARTER INPUT - KEY SIDE
87 - OPEN ca6153 revA
2012 Audiovox Electronics Corporation. All rights reserved.
35
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
36
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ca6153 revA
PROFESSIONAL
SERIES
Owner’s Guide ca6153
Deluxe Vehicle Security and
Remote Start System
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2012 Audiovox Electronics Corporation. All rights reserved.
1
2
Table of Contents
Using Your Remote Control ............................................................... 3
Arming the Security System ............................................................ 3
Passive Arming Bypass ................................................................... 3
Bypassing the Shock Sensor .......................................................... 3
Hidden Alarm Function ...................................................................... 3
Disarming the Security System ........................................................ 3
Two Stage Door Unlock (optional) ................................................... 4
Activating Trunk Release (optional) ................................................ 4
Activating Optional AUX 1 (optional) ............................................... 4
Using the Progressive Car Finder Feature ...................................... 4
Using the Personal Protection Alarm ............................................... 4
Programmed Transmitter Notification .............................................. 4
Valet Mode ........................................................................................ 5
Eliminating Arm / Disarm Notification Chirps .................................... 5
Manually Overriding the Security System ....................................... 5
Car Jack Mode .................................................................................. 6
Using Your Remote Vehicle Starter ................................................. 6
Remote Starting Your Vehicle .......................................................... 6
Remote Start Shutdown ................................................................... 6
Entering Your Vehicle while it is Running via Remote Start ........... 7
Preheating or Precooling the Vehicle’s Interior ............................... 7
User Programmable Run Time / Run Time Extension ...................... 7
Using the “Quick-Stop” Feature ....................................................... 7
Operating the 2 / 3 Hour Start Up Timer Mode ................................ 8
Turbo Timer Mode (optional) ............................................................ 8
Operating the Daily Start Timer ........................................................ 9
Remote Start Safety Features ......................................................... 9
LED and Siren/Horn Indications ....................................................... 10
Transmitter Button Functions ......................................................... 11
Replacing Remote Control Batteries ............................................. 12
Warranty Information ......................................................................... 13 ca6153 revA
Using Your Remote Control
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The
LED status indicator will blink steadily, once per second.
NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle.
Passive Arming Bypass
If passive arming is enabled on your system, while the system is disarmed, press
+ , the system will respond with 1 chirp and the LED will turn on. The security system will remain in this temporally bypassed state for as long as you wish. To exit passive bypass, press the or button and the system will return to normal status.
Bypassing The Shock Sensor
To arm the system and ignore the shock sensor press button, then within 5 seconds press + , the system will respond with 1 long chirp.
NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal operation the next time the system is armed.
Hidden Alarm Function
Press the button first, within 3 seconds press the button to activate the hidden alarm function. The security system will arm with “Hidden Alarm Function” in which the siren / horn will be silenced if the system is triggered.
Disarming the Security System
To disarm the system press the button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected).
NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle. If your system is set up for 2 step unlock, a third press of will activate the audible response.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more than 2 seconds.
2012 Audiovox Electronics Corporation. All rights reserved.
3
4
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button for 3 seconds will open the vehicle’s trunk or hatch.
Activating Optional AUX 1 (Optional)
If this feature is enabled on your system, pressing the and buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system.
Using the Progressive Car Finder Feature
Press the button to locate your vehicle. The system will flash the parking lights and sound 5 times at low volume, increasing in volume each time the button is pressed.
Using the Personal Protection Alarm (Panic)
Press and hold the button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the button on the transmitter again for 3 seconds. The system will automatically stop after 30 seconds.
Programmed Transmitter Notification
As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.
ca6153 revA
Valet Mode
When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below:
1.
Turn the vehicle’s ignition ON.
2.
Push and hold the programming/valet button.
3.
The LED will turn on solid when valet mode is active
4.
Release the programming/valet button.
Eliminating Arm / Disarm Notification Chirps
System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.
1.
Turn the ignition ON then OFF.
2.
Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system;
1.
Open the vehicle door. The alarm will sound.
2.
Turn the ignition key to the ON position.
3.
Within 10 seconds, press and release the valet push button switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.
2012 Audiovox Electronics Corporation. All rights reserved.
5
6
Car Jack Mode
This feature must be turned on in system programming, please consult your installing dealer.
Triggering Car Jack mode: While the ignition is ON and press and hold + for 2 seconds, the parking lights will flash 1 time and the system will act as follows;
1.
50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step.
2.
Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing.
3.
90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS
STATE UNTIL THE BATTERY IS DEPLETED.
OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 10 seconds.
Using Your Remote Vehicle Starter
Remote Starting Your Vehicle
To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off.
ca6153 revA
Entering the Vehicle while it is Running via Remote Vehicle Start
1.
Unlock the vehicle’s doors.
2.
Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3.
Insert the key into the ignition switch and turn to the ON or RUN position.
4.
Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle’s interior to your setting.
User Programmable Run Time / Run Time Extension
The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes. Follow the steps below to extend the vehicle’s run time.
1.
The remote start must already be active.
2.
Press and release the button 4 times.
3.
The system will chirp 1 time and flash the parking lights 4 times to confirm that the run time has been reset.
Using the “Quick-stop” Feature
If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.
To engage quick stop:
1.
Stop the vehicle and place the transmission in PARK.
2.
With your foot off the brake pedal, press and release the button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered.
3.
Remove the keys from the ignition and exit the vehicle. Press the
button to lock the vehicle’s doors if desired.
Note: Do not leave children or animals unattended in the vehicle when using the quick-stop feature.
2012 Audiovox Electronics Corporation. All rights reserved.
7
Operating the 2 / 3 Hour Start Up Timer Mode
The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming.
WARNING!
Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.
8
To begin the 2 / 3 hour start up timer mode:
1.
Turn the vehicle’s ignition ON then OFF.
2.
Press and hold the valet button.
3.
Press the button 4 times, the system will; a.
When set for 3 Hour (default) - chirp 2 times and flash the parking lights 4 times.
b.
When set for 2 Hour - chirp 1 time and flash the parking lights 2 times.
4.
Release the valet button.
To exit the 2 / 3 hour start up timer mode:
1.
Turn the vehicle’s Ignition ON.
OR
1.
Activate the remote vehicle start feature using the remote control.
Turbo Timer
This option will keep the engine running to allow the vehicle’s turbo to properly cool down before shutting the engine off.
To engage the Turbo Timer feature:
1.
With the vehicle running via the ignition key and your foot off of the brake pedal.
2.
Engage the vehicle’s parking brake and press the and buttons simultaneously.
3.
The vehicle’s parking lights will turn on to verify the Turbo Timer feature has been activated.
4.
Turn the ignition key OFF, the vehicle will continue to run until the preprogrammed time has elapsed (1, 3, or 5 minutes)
To disengage the turbo timer feature, press the vehicle’s brake pedal.
ca6153 revA
Operating the Daily Start Timer
The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process.
1.
Turn the ignition ON/OFF (vehicle must be disarmed).
2.
Within 10 seconds, while pressing the brake, press and release the button twice.
3.
The vehicle will emit 2 chirps and flash the parking lights 4 times.
Remote Start Safety Features
For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur:
1.
The vehicle hood is open.
2.
The brake pedal is pressed prior to turning the ignition key to the ON position.
3.
The engine is over-revved (tach checking only).
4.
Valet mode is active.
2012 Audiovox Electronics Corporation. All rights reserved.
9
10
LED and Siren/Horn Indications
LED Display Indications
LED
OFF
SLOW FLASH
FAST FLASH
ON (SOLID)
2 FLASH... PAUSE
3 FLASH... PAUSE
4 FLASH... PAUSE
5 FLASH... PAUSE
Function
DISARMED
ARMED
PASSIVE ARMING
VALET MODE
ZONE 2 TRIGGER, HOOD/TRUNK
ZONE 3 TRIGGER, DOOR
ZONE 4 TRIGGER, SHOCK
ZONE 5 TRIGGER, IGNITION
Siren/Horn Indications
Chirps
1
2
3
4
5
Function
DISARM
ARM
DOOR AJAR UPON ARMING
DISARM / TRIGGERED
CAR LOCATOR
Parking Light Flash Indications
Flashes Function
1
2
3
DISARM
ARM
DISARM / TRIGGERED
5 CAR LOCATOR
ON (SOLID) REMOTE STARTED ca6153 revA
Transmitter Button Functions
1 Way
Transmitter
Lock Unlock
Panic
Lock X
Unlock X
2 Step Unlock X
X Trunk
Car Finder X
X Panic
Remote Start
Remote Start
Shutdown
Run Time
Extention
AUX 1
Shock Bypass
X
X
X
X
X
X Hidden Alarm
Passive Arming
Bypass
Turbo Timer
X
X
X
2 / 3 Hour Start
Daily Start Timer X
X
X
X
X
X
X
Press and Release
Press and Release
Press and Release 2 times
Push and Hold (3 Sec)
Press and Release
Push and Hold (3 Sec)
Press and Release (1 or 2 times depending on selectable option)
Push and Hold (3 Sec)
Press and Release 4 times.
Push and Hold (3 Sec)
Press and Release Lock then
Press Lock + Car Find
Press and Release Car Fnd then
Press Lock
Press and Release
Press Unlock + Start
Ignition ON/OFF, Press and Hold
Valet Button, Press Start 4 times
Press Lock + Start
2012 Audiovox Electronics Corporation. All rights reserved.
11
Replacing Remote Control Batteries
1 Way 4 Button Remote Control (part # catxmt)
The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries:
1.
Remove 3 screws and disassemble the halves of the remote control.
2.
Remove the old batteries, observing the +/- symbols on the batteries and replace with new CR2016 batteries.
3.
Reassemble the halves of the remote control and install the 3 screws.
4.
Test operation of the remote control.
12 ca6153 revA
Code Systems, Inc. Limited Lifetime Warranty
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI-
NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts directly related to repairs of the defect(s).
Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for a period of one (1) year from the date of purchase of the Product.
CODE accessories, sold separately, are covered by the applicable warranty accompanying the accessory.
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product was originally installed is transferred to another party.
This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.
In order for the Product to be repaired or replaced under the terms of this warranty, the defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt. The date of purchase and year, make and model of the vehicle in which the
Product was originally installed must be clearly indicated on the sales receipt.
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED
OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-
RANTY, EXPRESS OR IMPLIED, WHATSOEVER.
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION
LABOR.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state
2012 Audiovox Electronics Corporation. All rights reserved.
13
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
14
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ca6153 revA
WARNING
THIS VEHICLE IS EQUIPPED WITH A REMOTE
CONTROLLED CAR STARTER
BEFORE SERVICING THIS VEHICLE, REMOVE THE MAIN
POWER FUSE (RED WIRE) TO THE CAR STARTER OR
DISCONNECT THE VEHICLE BATTERY.
LBL0675
MAXIMUM INSURANCE DISCOUNT AUTHORIZATION
Dear Insurance Agent,
The installation of my Code-Alarm automatic (passive) arming security system in the vehicle indicated below qualifies me for the max i mum discou n t mandated by law in some states and by insurance company option in others. This vehicle security system automatically arms itself after t he doors are closed and includes at least one engine disabling relay to prevent the engine from being started .
Insured Signature:
Street Address: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ State:
Name(pleaseprint): - - - - - - - - - - - - - - -
Vehicle Year/Make/Model: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Vehicle Identification #: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
The signature below certifies that my Code-Alarm automotive security system was installed on
Installer
Signature:-------------~----------------------------
Company: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Address:
PLEASE COMPLETE AND MAIL TO YOUR INSURANCE COMPANY
1026673
Thank you for purchasing a Code-Alarm product. We pride ourselves on the quality and reliability of all our electronic products, but if you ever need service or have a question, our customer service staff stands ready to help.
Contact us at www.Code-Aiarm.com
PRODUCT PROTECTION:
In case of an insurance loss such as fire, flood or theft, your registration will serve as proof of purchase.
PURCHASE REGISTRATION:
Registering On-Line will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.
1026350
/
CCCc~IA~m
Register online at:
.CODE-ALARM.COM
Click On Product Registration and Fill Out the Brief Questionnaire
L I M I T E D
$2,500.00 w
A R R A N T y
CODE SYSTEMS, Inc makes the following warranty to YOU as the original purchaser of this system.
Should YOUR private passenger vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM is originally installed by an authorized dealer and while the system is operational and activated be stolen and not recovered or if stolen and recovered be deemed a total loss for theft insurance purposes, then subject to the following conditions, YOU will be refunded the comprehensive auto insurance deductible on your existing insurance not to exceed $2,500.00.
This Limited Warranty is effective for thefts occurring within one (l) year from the original date of purchase providing that: (A) the attached registration forrn has been completed in full and received by the CODE-ALARM Program Administrator at the address shown below with postmark that is within five (5) business days from the original date of pur c hase; (B) YOU properly and completely identify the vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM has been installed ; (C) YOUR vehicle is registered within the United
States of America or Canada; (D) the theft of YOUR vehicle occurs within the United State s of America or Canada; ( E ) YOU file a complete theft report with the police or other law enforcement agency having jurisdiction at the location of the theft ; (F) YOU have comprehensive or theft insurance in force on the vehicle at the time of the theft and YOU have filed a claim for the theft of the vehicle with YOUR insurance carrier; and (G) the theft claim with YOUR insurance carrier is settled and fina l payment from them has been received.
This Limited Warranty applied solely to passenger vehicles , motor homes , and light duty trucks or vans not exceeding 13 , 500 GVW . It doe s not apply to any vehicle used in a busines s , for Livery or offered for hire . This Limited Warranty applies only to the vehicle as identified on the attached registration forrn .
In order to make a claim under the Limited Warranty, YOU are to provide the CODE-ALARM Program Administrator with the following information and materials:
• Proof of purchase including the purchase date .
YOU ARE URGED TO SAVE YOUR ORIGINAL RECEIPT
• A certified or notarized complete copy of the police report filed by YOU
• A copy of the original declaration sheet from the insurance policy in force at the time of the system purchase. This declaration sheet must clearly show the amount of the deductible applicable to theft losses
• A copy of the insuran ce company settlement check and any related documentation
\
CONTINUED ON REVERSE ADVc
THIS CARD MUST BE POSTMARKED WITHIN THIRfY (30)BUSINF.SS DAYS OF THE PURCHASE
OF YOUR CODE-AlARM ANTI-THEFT SYSTEM ORIGINAL PURCHASE RECEIPT MUST BE
RETAINED AND SUBMITTED WITH ANY CLAIMFlLED HEREUNDER
CONSUMER REGISTRATION CARD
Cod e Alarm Anti-Theft System Purchased Pur c h ase Date
Nam e Address
C i ty
Vehicle Year
I
State j
Make / Model
Z ip
YIN
I
Phon e
In s ur a n ce Carr ie r Policy Number
Amount of Comprehensive or Theft Deductible
Dealer Name
Price Paid Fo r Sys t em $
OPTIONAL IN FO RMA T I O N
Annual H ouse h o ld Income : s
I
Exp tres
Address
Age of Bu ye r :
W as In sta ll at i on In c lu ded ' ' Yes
Pu rc hased t o r : c::J No CJ
Yourself
CJ
As a Gift
CJ
Less th a n $20.000
CJ
$20-40,000
CJ
$40-60.000
CJ
M o re than $60,000
CJ
BY YOUR S I GN ATURE B E LOW , YOU (I) AGREE TO ALL OF T H E TERMS AND COND ITI ONS SET FORTH IN THIS LI M I TED WARRANTY
AND (2) YOU UNDERSTAND AND A G RE E THAT CODE SYSTEMS , In< I S PROVIDING YOU WITH A LIMITED WARR ANTY AND THAT
THIS LIMITE D WARRANTY I S NO T AN I NSURANCE POLICY .
S i g n a tur e D a t e
A D V - - C
1026699
The CODE-ALARM Program Administrator reserves the right to ask for any other similar do c umentation or other materials that may be reasonably required to verify YOUR claim. All documentation received on a claim becomes the Code-Alarm
Program Administrator's property and will not be returned .
All claim information must be mailed to the Code-Alarm Program Admini s trator within thirty (30) bu s iness days after receipt of the final settlement check from YOUR insurance carrier.
For the protection of YOUR rights, YOU are urged to make copies of all materials submitted and to send all materials via registered mail or any other means such that YOUR package can be traced in the event of its becoming lost or misdirected. The Code-
Alarm Program Administrator is not responsible for materials not received in the CODE-ALARM Program Administrator
' s office. Please allow four (4) to six (6) weeks to proce s s any claim hereunder .
This limited warranty i s not an insurance polic y or insurance coverage a nd is contingent on the e xistence of and payment from an underlying comprehensive auto insurance coverage and your compliance with all the terms and conditions set forth herein. This limited warranty has no cash value and is subject to all the terms and conditions set forth within this document.
This warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES . INCL U DING ANY IMPLIED
WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY, IN N O
CASE SHALL CODE-ALARM OR THE CODE-ALARM PROGRAM ADMI N ISTRATOR BE LIABLE FOR ANY CONSE-
QUENTIAL OR INCIDENTAL DAMAGES FOR BREA C H OF THIS OR ANY OTHER WARRANTY , EXPRESSED OR
IMPLIED, WHATSO E VER. No per s on or representative i s authorized to a ss ume for the C o mpany any liability other than e xpres s ed herein in c o nnection with th e s a le of thi s product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to YOU. This warranty gives YOU specific legal rights and YO
U may also ha v e other rights which vary from state to state.
THIS WARRA N TY AND WARRANTY PROGRAM IS NOT A V AILABLE AND MAY NOT BE
MARKETED IN OR FROM THE STATE OF FLORIDA .
THE CODE-ALARM PROGRAM ADMINISTRATOR
Post Office Box 231809
Encinitas, CA 92023
Phone (800) 708 2113
CODE-ALARMLIMITEDWARRANTYPROGRAM
Post Office Box 231809
Encinitas, CA 920 2 3
POST OFFIC E
WILL NOT
DELIVER
WITHOUT P ROPER
POSTAGE A FFIXED
H ERE

Public link updated
The public link to your chat has been updated.
Advertisement