Mounts by PDM 625T-8 PANEL DISPLAY MOUNT Instruction manual

Mounts by
A division of David Engineering & Mfg. Inc.
Model
PDM 625T-8 PANEL DISPLAY MOUNT
Thank you for purchasing the PDR panel display wall mount.
To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference.
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
We are not liable for improper installation that results in damage to mounts, adapters or presentation equipment.
Special techniques are necessary for installation of the panel display mount.
?
Do not attempt to perform this work by yourself.
?
Request an installation specialist to install this unit.
?
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
?
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the mounting
unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and airflow.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the
weight of both the display and the mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Features
Low profile 2 5/8”
16”, 24” or 32” stud mounting
Easy installation
Flat to 13 deg tilt
Lateral movement from center for better viewing position
1
INSTALLATION LOCATION
WARNING
The wall where the wall mount is to be installed must be capable of long-term support of the total load of
the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to
withstand the force of earthquakes, vi bration and other external forces.
Note: Incorrect installation can cause the p anel display to fall and cause injury.
Total load of the panel (p anel display + wall mount)
MAXIMUM WEIGHT 300 LBS (138 kg)
INSTALLATION ON A WOODEN WALL
Always install so that the load is supported by a wood stud. If the strength of the wood studs is not sufficient, add reinforcement.
Do not install on decorative posts or plaster board.
Always confirm the center of the stud is used for the installation.
CAUTION
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
water is possible. These can result in fire or electric shock.
Do not install close to an air conditioner intake or outlet. Do not install in locations where there are excessive amounts of dust,
oily smoke or tobacco smoke. Fire could result.
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation.
.
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.
. on a vertical surface. Avoid sloped surfaces. Also, do not install facing upward. The internal temperature could
Install only
elevate and possibly result in fire. Injury or damage could also result from falling.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
falling.
Do not install where there is direct sunlight or other strong light. Strong light could result in eye fatigue during usage.
WARNING
Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the panel
display falls.
Do not alter any of the parts. Do not use broken parts. This could result with injury due to the panel display falling.
Make sure that both hooks from the each pivot bracket engage with the wall bracket . Failure to do so could cause the panel
display to fall.
Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.
C a u t i o n : I n s t a l l a t i o n o f u n i t i s t o b e c a r r i e d o u t b y q u a l i f i e d t e c h n i c i a n s o n l y. I n s t a l l i n a n a p p r o p r i a t e
location by checking the wall structure and durability for safety and accident prevention.
Rev 021908
2
Product specification
36.00”
33.35” MAX
847mm
3.94”
100mm
3.94”
100mm
7.71”
25.50”
5.39”
24.61”
625mm
4.00”
13°
2.64”
3
PARTS LIST
A
Display bracket .... 2 pcs
B
Wall mount bracket…1 pc
C
Locking bar... 2 pc
D
I
5/16” Flat washers...6 pcs Plastic spacer 3/4 x 1”...4 pcs
J
E
5/16’ x 2 ½”Lag bolts...6 pcs Multi mount washer ...4 pcs
K
F
5mm x 40mm... 4 pcs
5mm x 16mm...4 pcs
L
G
6mm x 40mm...4pcs
6mm x 16mm...4 pcs
H
M
8mm x 16mm...4pcs
8mm x 40mm...4pcs
MOUNTING ARM ASSEMBLY
Fig 1
TOP
BOTTOM
LEFT HAND SHOWN RIGHT HAND OPPOSITE
4
1. FASTEN MOUNTING PLATE TO WALL
The bracket must be secured to the wall studs capable of at least (4) times the weight of the unit. The wall bracket should be mounted at the same horizontal center line
as the display center line ( viewing horizontal center line). Using the six lag bolts ( E ) and washers supplied ( D ), level and secure the mounting plate to the center of
the wall studs. Pre drill 3/16” (5mm) hole for lag bolts. See Fig 2
Fig 2
VIEWING
HORIZONTAL
CENTER LINE
WOOD STUDS
(std construction 2 x 4 studs/1/2” wallboard)
16"
32"
FLOOR LINE
2. SECURE THE DISPLAY BRACKETS TO THE MONITOR
Lay the display panel face down on a protected surface.
Position the left and right hand bracket (A) with the holes facing towards the bottom.
See Fig. 3 Note bottom edge.
Using the proper screws (F,G,H) and multi washer (J) supplied position the brackets equal distance from the top and bottom edge ,
and tighten hardware.
Additional hardware is supplied (screws K,L,M) and plastic spacers (I) to be used if needed for different display mounting
applications.
Note: Do not over tighten the bracket mounting screws as damage to the displays internal mounting threads could occur.
Fig 3
Square Multi-mount washer (J)
Mounting hardware F,G,H,K,L,M
Display bracket ( A ) right
Display bracket ( A ) left
Plastic spacer ( I )
Panel display bottom edge
5
3. MOUNT THE DISPLAY TO THE WALL MOUNT BRACKET
Lift the display, with the brackets attached, onto the wall plate. See Fig 4
Position the top and bottom into the slots. See Fig 5 and 6
Make sure the display brackets engage the rails on the wall mount bracket (B) See Fig 5
Insert the locking bar (C) as shown in Fig 5 with the locking holes facing up to match the holes in the wall mount bracket (B) .
Secure with a padlock (not supplied) thru holes in the locking bar (C) and wall mount bracket (B) Fig 5
Fig 5
Fig 4
Locking bar (C)
4. ADJUST LATERAL MOVEMENT AND TILT
Lateral Movement:
Once the display on the wall is complete, you can still move the display left to right to optimize the final viewing position
by gently sliding the unit on the wall bracket. The adjustment distance will vary depending on the display size being
used. See Fig 7
Tilt adjustment:
Tilt adjustment can be made by holding the top of the display and loosening both tri knobs.
After tilt adjustment is complete, tighten both tri knobs. See Fig 6
Fig 6
13°
Fig 7
Tri knob
6