Primus / Lavamac LH75 Installation Manual
Below you will find brief information for washer LH 75. This instruction manual describes the washer LH 75, its features, installation and operation. With the washer LH 75 you can wash different types of laundry and use steam as a heating source. The washer LH 75 has a capacity of 7 kg and is suitable for load ratio 1:10. You need to connect the washer LH 75 to water supply, drain and electricity.
advertisement
◉
Touch to zoom
© D SS N N SN 660 _ 585 _||_ 50 HTO/0 _ 685 N FRONT VIEW LEFT VIEW REAR VIEW FRAME FIXATION DIMENSION anchoring bolts A € LEGEND: 7 7 \\ | 1. Electronic programmer 11. Cold soft water connection Lo 2. Door handle 12. Cold hard water connection > 3. Service panel 13. Control panel | =} 4. Air ventilation 14. Main switch = 9. Liquid soap hose 15. Fuses 50 || 560 | 50 connection 16. Main power supply E E 6. Name plate 17. Power supply to A /. Steam connection liquid soap pumps 8. Drain outlet 18. Soap hoppers 9. Earthing connection 19. Adjustable leg 10. Warm water connection The machine must be located on a leveled concrete floor or on a elevation base ant should be secured by means of anchoring boltes to assure the safety. The machine must reliably rest in all four corners of the machine! The floor must comply static and dynamic stress. Anchoring bolts are not part of delivery of machine. WATER CONNECTION The washing machine has been designed for connection of three waters (cold hard, cold soft and hot). It is also necessary to connect all available waters to a water supply. Inlet valves 7” for cold and hot water are delivered with the machine. Mount shut-off valves 7” to the water supply pipes For connection of the machine to water inlet shut-off valves we recomend to use enclosed flexible hoses with couplings A. WATER DRAIN CONNECTION The washer is equipped with drain pipe of /5mm diameter without pump. These must be connected to the waste sump or central waste drain. For these purposes you can use rubber elbow, which is a part of delivery. Put the stench trap in drain pipe. The maximum temperature of waste water from washer is 70:80°C (for programm No.1 — hot washing). Quantity of draining water — 42 |/min. TECHNICAL SPECIFICATION Capacity: load ratio 1:10 7 Ка / 16 lbs Inner drum dimension: diameter 530mm / 20.9" depth 330mm / 12.99” Drum volume 73 dm*/ 19.28 qal Drum revolutions: wash 48 rpm high extraction 1000 rpm G—factor: 300 [Machine dimensions (max.): width 660mm / 26” depth 770mm / 30.31” height 1080mm / 42.52” Weight netto 235 kg / 519 lb brutto 250 kg / 552 Ib IMachine electrical execution: E: 3Xx380-415V+N 50H7 S: 1x220—240V 50Hz (can be connected to 3x380—415V 50Hz) Rated motor power: Rated heating power input (E version): Rated input power of the machine 0.75 kW 6 kW E: 6.9 kW S: 0.9 kW Power supply protection: with electrical heating: without heating: 6kW/3AC 400V/16A 1AC 230V/16A IMotor overloading protection: frequency convertor protection Conductors section: E: 5x1.5 mm*Cu S: 3x1.5 mm?*Cu Water connections: water pressure 0.2:0.6 MPa / 39:87 psi steam pressure average steam consumption: maximum steam consumption: water connection 3x 3/4 drain connection external diameter 876 mm / 3 Version with steam heating (S): steam connection 1/2” 0.3:0.8 MPa / 45-116 psi 7 kg/hod / 15.4 Ib/hour 0.008 kg/sec / 0.0176 Ib/sec Connections to liquid detergents: о Max. static load (with textile and water) 2492 N Max. dynamic load (intermittent vibrations) 730 N Frequency of dynamic load 16 Hz Date: 25.04.01 No. 01-133—2 LH Author: |TR. Index/date |E/07.2008 lavamac 75 WASHER - EXTRACTOR
advertisement
Key Features
- 7 kg capacity
- Steam heating
- Load ratio 1:10
- Inner drum dimension
- External dimensions
- Water connections
- Drain connection
- Power supply protection
- Motor overloading protection
- Max dynamic load
Frequently Answers and Questions
How to connect washer to water supply?
The washer is designed for connection of three waters (cold hard, cold soft and hot). It is also necessary to connect all available waters to a water supply. Inlet valves 3/4" for cold and hot water are delivered with the machine. Mount shut-off valves 3/4" to the water supply pipes. For connection of the machine to water inlet shut-off valves we recomend to use enclosed flexible hoses with couplings 3/4".
What kind of drain connection is required?
The washer is equipped with drain pipe of 75mm diameter without pump. These must be connected to the waste sump or central waste drain. For these purposes you can use rubber elbow, which is a part of delivery. Put the stench trap in drain pipe.
What is the maximum temperature of waste water?
The maximum temperature of waste water from washer is 70-80°C (for programm No.1 — hot washing).
Related manuals
Download
PDF
advertisement