5301146

MODEL NO. LG-25-PM

5301147

MODEL NO. LG-25-SM

25 Gallon Lawn & Garden Spot Sprayers

ASSEMBLY / OPERATION INSTRUCTIONS / PARTS

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON, PLEASE CALL

1-800-831-0027

IF YOU SHOULD HAVE A QUESTION OR

EXPERIENCE A PROBLEM WITH YOUR

FIMCO INDUSTRIES PRODUCT:

1-800-831-0027

BEFORE YOU CALL, PLEASE HAVE THE

FOLLOWING INFORMATION AVAILABLE:

SALES RECEIPT & MODEL NUMBER. IN MOST

CASES, A FIMCO INDUSTRIES EMPLOYEE CAN

RESOLVE THE PROBLEM OVER THE PHONE.

Your authorized dealer is the best source of replacement parts and service. To obtain prompt, efficient service, always remember to give the following information:

1. Correct part description and part number.

2. Model Number of your sprayer.

3. Serial Number of your sprayer.

Part description and part numbers can be obtained from the illustrated parts list section of this manual.

Whenever you need parts or repair service, contact your distributor / dealer first. For warranty work always take your original sales slip, or other evidence of purchase date, to your distributor / dealer.

TECHNICAL SPECIFICATIONS

GENERAL INFORMATION

The purpose of this manual is to assist you in operating and maintaining your lawn and garden sprayer. Please read it carefully as it furnishes information which will help you achieve years of dependable trouble free operation.

• Corrosion Resistant Polyethylene Tank.

• 12 Volt Diaphragm Pump.

• Pressure Gauge-Adjustable Pressure Range.

• 15 Foot Handgun Hose.

CAUTION: Always check the vehicle load rating before using this sprayer. The loaded weight of the sprayer and boom assembly is about 170 lbs. when the tank is full for a 15 gallon unit and 250 lbs. for a 25 gallon unit.

WARNING

DO NOT USE PUMP IN AN EXPLOSIVE

ENVIRONMENT. DO NOT USE TO PUMP

FLAMMABLE FLUIDS, GASOLINE,

KEROSENE FUEL, OIL, ETC.

WARRANTY / PARTS / SERVICE

Products are warranted for one year from date of purchase against manufacturer or workmanship defects.

W W W . F I M C O I N D U S T R I E S . C O M

1000 FIMCO LANE • P.O. BOX 1700 • NO. SIOUX CITY, SD 57049

TOLL FREE: 800-831-0027 • TOLL FREE FAX: 800-494-0440

Form No. 1311 (5004805 1/07)

It is important to test the sprayer with plain water before actual spraying is attempted. This will enable you to check the sprayer for leaks in the plumbing system.

ASSEMBLY

CAUTION

PRESSURE SWITCH OPERATION

Pressure switch is pre-set at the factory. Improper adjustment of the pressure switch, may cause severe overload or premature failure. If the pump is subjected to rapid cycling during normal operation, or infrequent periods, damage may occur.

The sprayer is partially assembled at the factory. Follow the instructions below to complete the assembly of this unit.

1. Thread the gauge into Item 18.9. Use a good grade of thread sealant here to insure no leaks.

2. Connect the wiring harness to the wires coming out of the pump. Connect the wiring from the wiring assembly to the 12

Volt power source of the vehicle. The red wire of the 2-wire set must be connected to the positive (+) post on the battery or the "hot" connection on a switch or to the ammeter. The brown wire may be grounded or connected to the negative

(-) post on the battery.

WARNING: Some chemicals will damage the pump valves if allowed to soak untreated for a length of time. Always flush the pump with water after use. Do not allow chemicals to sit in pump for extended times of idleness. Follow the chemical manufactures instructions on disposal of all waste water from the sprayer.

AFTER SPRAYING

3. Remove the drain plug assembly from the parts bag and thread it onto the drain bung located at the lower rear end of the tank.

After use fill the sprayer part way with water, start the sprayer and allow clear water to be pumped through the plumbing system and out through the handgun. Use the handgun on the sprayer to thoroughly wash all internal parts of the tank and tank cover.

4. Remove the handgun clips/screws from the parts bag, if applicable, and attach them to the side of the tank, for handgun storage.

Refill the tank about half full with plain water and use a chemical neutralizer such as Nutra-Sol or equivalent and repeat cleaning instructions above. Flush the entire sprayer with the neutralizing agent. Follow the chemical manufacturers disposal instructions of all wash or rinsing water.

OPERATION

WINTER STORAGE

The pump on the sprayer is equipped with a pressure switch that is factory set at a maximum of 60 PSI. Pressure may be decreased by opening the regulating valve. The more it is opened, the lower the pressure will be.

Drain all water out of sprayer paying special attention to pump, valves, and handgun. These items are especially prone to damage from chemicals and freezing weather.

The handgun has an adjustable nozzle which allows the spray to be adjusted from a cone shaped fine mist to a straight stream. It is normal for the pump to cycle when spraying with a fine mist spray.

The sprayer should be winterized before storage by pumping a solution of R.V. anti-freeze through the entire plumbing. Proper care and maintenance will prolong the life of the sprayer.

Page 2

Page 3

Page 4