Utax CD 1252 Copy System Operation Guide
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
▼
Scroll to page 2
of
424
CD 1242 | 1252 INSTRUCTION HANDBOOK digital multifunctional system Introduction Thank you for your purchase of CD 1242/CD 1252. This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. Please read this Operation Guide before you start using the machine, and keep it close to the machine for easy reference. We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. In this Operation Guide, CD 1242 and CD 1252 are referred to as 42 ppm model and 52 ppm model respectively. Included Guides The following guides are supplied with the machine. Refer to them as necessary. Operation Guide (This Guide) Describes how to load paper, basic copy, print and scan operations, and troubleshooting. Safety Conventions in This Guide The sections of this guide and parts of the machine marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the machine. The symbols and their meanings are indicated below. WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points. CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points. Symbols The symbol indicates that the related section includes safety warnings. Specific points of attention are indicated inside the symbol. .... [General warning] .... [Warning of danger of electrical shock] .... [Warning of high temperature] The symbol indicates that the related section includes information on prohibited actions. Specifics of the prohibited action are indicated inside the symbol. .... [Warning of prohibited action] .... [Disassembly prohibited] The symbol indicates that the related section includes information on actions which must be performed. Specifics of the required action are indicated inside the symbol. .... [Alert of required action] .... [Remove the power plug from the outlet] .... [Always connect the machine to an outlet with a ground connection] Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are illegible or if the guide itself is missing (fee required). NOTE: An original which resembles a bank note closely may not be copied properly in some rare cases because this machine is equipped with a counterfeiting prevention function. OPERATION GUIDE i Contents Contents Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Caution / Warning Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Precautions for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Safety Instructions Regarding the Disconnection of Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Legal Restriction on Copying/Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii Legal and Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix 1 Part Names Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2 Preparation before Use Check the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Determining the Connection Method and Preparing Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Power On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Sleep and Auto Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Adjusting the Operation Panel Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Switching the Language for Display [Language]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Setting Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Network Setup (LAN Cable Connection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Installing Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Embedded Web Server (Settings for E-mail). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Sending E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Loading Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 Loading Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 3 Basic Operation Login/Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Enter key and Quick No. Search key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Touch Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Original Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Printing - Printing from Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21 Sending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Confirmation Screen of Destinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29 Specifying Destination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 Using Document Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33 Basic Operation for Document Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35 Canceling Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-42 Quick Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43 Program (Copying and Sending). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-46 Registering Shortcuts (Copy, Send, and Document Box Settings) . . . . . . . . . . . . . . . . . . . . . . 3-48 Using the Internet Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49 4 Copying Functions Original Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Paper Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 ii OPERATION GUIDE Contents Mixed Sized Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Original Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Output Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Combine Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Margin/Centering Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Border Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Booklet from Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Cover Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Form Overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Page Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Memo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 Image Repeat/Double Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 EcoPrint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Sharpness Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Continuous Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31 Auto Image Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Negative Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Mirror Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33 Job Finish Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 File Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 Priority Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 Repeat Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36 5 Sending Functions Original Size Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Sending Size Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Centering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Mixed Sized Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 1-sided/2-sided Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Original Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 File Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 File Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 PDF Encryption Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Adjusting Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17 Scan Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18 Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19 Background Density Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20 Color / Grayscale / Black and White Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 Continuous Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 Border Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 Border Erase to Back Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24 Enter Document Name/File Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25 Enter E-mail Subject and Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26 WSD Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27 Job Finish Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29 Send and Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 Send and Store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 FTP Encrypted TX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Color Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 About Color Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32 6 Document Box OPERATION GUIDE iii Contents Using a Custom Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Using a Job Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Printing Documents Stored in Removable USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 Saving Documents to USB Memory (Scan to USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 7 Status / Job Cancel Checking Job Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Checking Job History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 Sending the Job Log History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11 Pause and Resumption of Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 Canceling of Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 Priority Override for Waiting Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Reordering Print Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Checking the Remaining Amount of Toner and Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 Device/Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16 8 Default Setting (System Menu) Common Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Copy Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26 Sending Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29 Document Box Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 Printer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 Printing Reports/Sending Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39 Adjustment/Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-42 Date/Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-47 Editing Destination (Address Book/Adding One Touch Keys). . . . . . . . . . . . . . . . . . . . . . . . . . 8-51 Internet Browser Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-58 Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-60 System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-63 Restarting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-63 Network Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-64 Secure Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-69 Interface Block Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-72 Security Level (Security Level setting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-73 Document Guard Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-73 Optional Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-75 Accessibility Display (Enlarged Touch Panel Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-77 9 Maintenance Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Toner Container and Waste Toner Box Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 10 Troubleshooting Solving Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Responding to Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Clearing Paper Jams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-15 11 Management User Login Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 Job Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14 Data Security Kit Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-27 Appendix Optional Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-2 iv OPERATION GUIDE Contents Character Entry Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-10 Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-13 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-21 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-27 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Index-1 OPERATION GUIDE v Quick Guide Be sure to read Precautions for Use before using this machine. Administrator tasks To make copies It copies. To print Simply press the Start key to make copies. You can also fine-tune the copy settings by changing the paper size, adjusting the density, etc. What you want to do Copying with specific settings It prints. You can print via a network or print a PDF file directly from USB memory. Printing Documents Stored in Removable USB Memory Print via a network Connecting Cables Network Setup (LAN Cable Connection) Install the printer driver on your computer *1 Setup Loading Paper...2-19 Placing Originals on the Platen...2-30 Operation Copying Functions ...4-1 Printing Documents Stored in Removable USB Memory... 6-20 Printing Printing from Applications ...3-21 *1: For more information, refer to the Printer Driver User Guide. vi OPERATION GUIDE Administrator tasks To send documents It sends. You can send scanned images via a network. Or, you can also store scanned images in USB memory. What you want to do Send to Folder (SMB) Send as E-mail Saving Documents to USB Memory Connecting Cables Network Setup (LAN Cable Connection) Plug the USB memory Create a shared folder on the destination computer. Setup Editing Destination (Address Book/Adding One Touch Keys)...8-51 Place the originals on the platen Operation Sending...3-23 *1 Sending Functions...5-1 Saving Documents to USB Memory (Scan to USB)...6-22 *1: If the destination is not stored in the address book, you can send by entering the address directly. OPERATION GUIDE vii Administrator tasks To send a FAX As well as sending a FAX via the telephone lines, you can also send a FAX via a network. It faxes. NOTE: For more information on setting up and sending a FAX, refer to the FAX System (S) Operation Guide. What you want to do Send a FAX FAX directly from a computer FAX without using the telephone line (Internet FAX (i-FAX)) Connect the modular cord for the telephone line to this machine. Selection of Telephone Line (Inch version only) Network Setup (LAN Cable Connection) Install the Network FAX Driver on your computer *1 Setup Selection of Transmit Terminal Identification (TTI)...2-3 on the FAX System (S) Operation Guide *2 Loading Paper...2-19 Operation FAX Operation (Basic)...3-1 on the FAX System (S) Operation Guide About Network FAX...9-1 on the FAX System (S) Operation Guide Internet Fax (i-FAX) (Optional)...8-1 on the FAX System (S) Operation Guide *1:For more information, refer to the Network FAX Driver Operation Guide. *2: If the destination is not stored in the address book, you can send the FAX by entering the address directly. viii OPERATION GUIDE Caution / Warning Labels Caution / Warning labels have been attached to the machine at the following locations for safety purposes. Be sufficiently careful to avoid fire or electric shock when removing a paper jam or when replacing toner. High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. Do not incinerate toner and toner container. Dangerous sparks may cause burn. Label inside the machine (Laser radiation warning) Moving parts inside. May cause personal injury. Do not touch moving parts. High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. NOTE: Do not remove these labels. OPERATION GUIDE ix Installation Precautions Environment CAUTION Avoid placing the machine on or in locations which are unstable or not level. Such locations may cause the machine fall down or fall over. This type of situation presents a danger of personal injury or damage to the machine. Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the power plug, clean the plug to avoid the danger of fire or electrical shock. Avoid locations near radiators, heaters or other heat sources, or locations near flammable items to avoid the danger of fire. To keep the machine cool and facilitate changing of parts and maintenance, allow access space as shown below. Leave adequate space, especially around the rear cover, to allow air to be properly ventilated out of the machine. 3 15/16" 10 cm 11 13/16" 30 cm 11 13/16" 30 cm 39 3/8" 100 cm Other precautions The service environmental conditions are as follows: • Temperature: 50 to 90.5 • Humidity: 15 to 80% F (10 to 32.5 C) However, adverse environmental conditions may affect the image quality.Avoid the following locations when selecting a site for the machine. • Avoid locations near a window or with exposure to direct sunlight. • Avoid locations with vibrations. • Avoid locations with drastic temperature fluctuations. x OPERATION GUIDE • Avoid locations with direct exposure to hot or cold air. • Avoid poorly ventilated locations. If the floor is delicate against casters, when this machine is moved after installation, the floor material may be damaged. During copying, some ozone is released, but the amount does not cause any ill effect to one’s health. If, however, the machine is used over a long period of time in a poorly ventilated room or when making an extremely large number of copies, the smell may become unpleasant. To maintain the appropriate environment for copy work, it is suggested that the room be properly ventilated. Power supply/Grounding the machine WARNING Do not use a power supply with a voltage other than that specified. Avoid multiple connections in the same outlet. These types of situations present a danger of fire or electrical shock. Plug the power cord securely into the mains power outlet and the power socket on the machine. A buildup of dust around the prongs on the plug or contact between the prongs and metallic objects may cause a fire or electric shock. Incomplete electrical contact could cause overheating and ignition. Always connect the machine to an outlet with a ground connection to avoid the danger of fire or electrical shock in case of an electric short. If an earth connection is not possible, contact your service representative. Other precautions Connect the power plug to the closest outlet possible to the machine. Handling of plastic bags WARNING Keep the plastic bags that are used with the machine away from children. The plastic may cling to their nose and mouth causing suffocation. OPERATION GUIDE xi Precautions for Use Cautions when using the machine WARNING Do not place metallic objects or containers with water (flower vases, flower pots, cups, etc.) on or near the machine. This type of situation presents a danger of fire or electrical shock should they fall inside. Do not remove any of the covers from the machine as there is a danger of electrical shock from high voltage parts inside the machine. Do not damage, break or attempt to repair the power cord. Do not place heavy objects on the cord, pull it unnecessarily or cause any other type of damage. These types of situations present a danger of fire or electrical shock. Never attempt to repair or disassemble the machine or its parts as there is a danger of personal injury, fire, electrical shock or exposure to the laser. If the laser beam escapes, there is a danger of it causing blindness. If the machine becomes excessively hot, smoke appears from the machine, there is an odd smell, or any other abnormal situation occurs, there is a danger of fire or electrical shock. Turn the main power switch off immediately, be absolutely certain to remove the power plug from the outlet and then contact your service representative. If anything harmful (paper clips, water, other fluids, etc.) falls into the machine, turn the main power switch off immediately. Next, remove the power plug from the outlet to avoid the danger of fire or electrical shock. Then contact your service representative. Do not remove or connect the power plug with wet hands, as there is a danger of electrical shock. Always contact your service representative for maintenance or repair of internal parts. xii OPERATION GUIDE CAUTION Do not pull the power cord when removing it from the outlet. If the power cord is pulled, the wires may become broken and there is a danger of fire or electrical shock. (Always grasp the power plug when removing the power cord from the outlet.) Always remove the power plug from the outlet when moving the machine. If the power cord is damaged, there is a danger of fire or electrical shock. Always hold the designated parts only when lifting or moving the machine. If this machine will be left unused for an extended period (e.g. overnight), turn it off at the main power switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power plug from the outlet as a safety precaution. If the optional Fax kit is installed, note that turning the machine off at the main power switch disables fax transmission and reception. For safety purposes, always remove the power plug from the outlet when performing cleaning operations. If dust accumulates within the machine, there is a danger of fire or other trouble. It is therefore recommended that you consult with your service representative in regard to cleaning of internal parts. This is particularly effective if accomplished prior to seasons of high humidity. Consult with your service representative in regard to the cost of cleaning the internal parts of the machine. Other precautions Do not place heavy objects on the machine or cause other damage to the machine. Do not open the front cover, turn off the main power switch, or pull out the power plug during copying. When lifting or moving the machine, contact your service representative. When moving the machine, please turn the four adjusters of the paper feeding unit until they reach the floor in order to stabilize the machine. Do not touch electrical parts, such as connectors or printed circuit boards. They could be damaged by static electricity. Do not attempt to perform any operations not explained in this guide. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or painful. This machine comes equipped with an HDD (hard disk drive). Do not attempt to move the machine while the power is still on. Since any resulting shock or vibration may cause damage to the hard disk, be sure to turn off the power before attempting to move the machine. In the event there is a problem with the machine’s HDD (hard disk drive), stored data may be erased. It is recommended that important data be backed up on a PC or other media. Be also sure to store originals of important documents separately. OPERATION GUIDE xiii Cautions when handling consumables CAUTION Do not attempt to incinerate the toner container or the waste toner box. Dangerous sparks may cause burns. Keep the toner container and the waste toner box out of the reach of children. If toner happens to spill from the toner container or the waste toner box, avoid inhalation and ingestion, as well as contact with your eyes and skin. • If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly with a large amount of water. If coughing develops, contact a physician. • If you do happen to ingest toner, rinse your mouth with water and drink 1 or 2 cups of water to dilute the contents of your stomach. If necessary, contact a physician. • If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any remaining tenderness, contact a physician. • If toner does happen to get on your skin, wash with soap and water. Do not attempt to force open or destroy the toner container or the waste toner box. If the optional Fax kit is installed and the main power switch is off, transmitting/receiving Fax is disabled. Do not turn off the main power switch, but press the Power key on the operation panel to enter Sleep. Other precautions Return the exhausted toner container and waste toner box to your dealer or service representative. The collected toner container and waste toner box will be recycled or disposed in accordance with the relevant regulations. Store the machine while avoiding exposure to direct sunlight. Store the machine in a place where the temperature stays below 40ºC while avoiding sharp changes of temperature and humidity. If the machine will not be used for an extended period of time, remove the paper from the cassette and the Multi Purpose (MP) Tray, return it to its original package and reseal it. xiv OPERATION GUIDE Laser Safety Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically sealed within the protective housing and external cover. In the normal operation of the product by user, no radiation can leak from the machine. This machine is classified as Class 1 laser product under IEC 60825. Caution: Performance of procedures other than those specified in this manual may result in hazardous radiation exposure. These labels are attached to the laser scanner unit inside the machine and are not in a user access area. The label shown below is attached on the right side of the machine. OPERATION GUIDE xv Safety Instructions Regarding the Disconnection of Power Caution: The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source. VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind nur Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen. DECLARATION OF CONFORMITY TO 2004/108/EC, 2006/95/EEC, 93/68/EEC and 1999/5/EC We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following specifications. EN55024 EN55022 Class B EN61000-3-2 EN61000-3-3 EN60950-1 EN60825-1 EN300 330-1 EN300 330-2 EN62301 Radio Frequency Transmitter This machine contains the transmitter module. We, the manufacturer hereby declare that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Radio Tag Technology In some countries the radio tag technology used in this equipment to identify the toner container may be subject to authorization and the use of this equipment may consequently be restricted. NOTE: Product marked with the Crossed-out Wheeled Bin Symbol includes the battery that complies with the European Parliament and Council Directive 2006/66/EC (the "Battery Directive") in European Union. Do not remove and dispose of the batteries included in this machine. xvi OPERATION GUIDE Legal Restriction on Copying/Scanning • It may be prohibited to copy/scan copyrighted material without permission of the copyright owner. • Copying/Scanning the following items is prohibited and may be penalized by low. It may not be limited to these items. Do not knowingly copy/scan the items that are not to be copied/ scanned. Paper money Bank note Securities Stamp Passport Certificate • Local laws and regulations may prohibit or restrict copying/scanning of other items not mentioned above. OPERATION GUIDE xvii xviii OPERATION GUIDE Legal and Safety Information Please read this information before using your machine. This chapter provides information on the following topics. • • • • • • • Legal Information ................................................................................. xx Regarding Trade Names..................................................................... xxi Energy Saving Control Function ........................................................ xxv Automatic 2-Sided Copy Function ..................................................... xxv Paper Recycling................................................................................. xxv Energy Star (ENERGY STAR®) Program.......................................... xxv About this Operation Guide................................................................xxvi OPERATION GUIDE xix Legal Information Copying or other reproduction of all or part of this guide without the prior written consent of UTAX GmbH is prohibited. xx OPERATION GUIDE Regarding Trade Names • PRESCRIBE and ECOSYS are trademarks of Kyocera Corporation. • KPDL is a trademark of Kyocera Corporation. • Microsoft, MS-DOS, Windows, Windows NT and Internet Explorer are registered trademarks of Microsoft Corporation in the U.S.A. and/or other countries. • Windows Me, Windows XP and Windows Vista are trademarks of Microsoft Corporation. • PCL is a trademark of Hewlett-Packard Company. • Adobe Acrobat, Adobe Reader and PostScript are trademarks of Adobe Systems, Incorporated. • Ethernet is a registered trademark of Xerox Corporation. • Novell and NetWare are registered trademarks of Novell, Inc. • IBM and IBM PC/AT are trademarks of International Business Machines Corporation. • Power PC is a trademark of IBM in the U.S.A. and/or other countries. • AppleTalk is a registered trademark of Apple Computer, Inc. • This machine has been developed using embedded real-time operating system Tornado™ by Wind River Systems, Inc. • TrueType is a registered trademark of Apple Computer, Inc. • TypeBankG-B, TypeBankM-M and Typebank-OCR are trademarks of TypeBank®. • All European language fonts installed in this machine are used under licensing agreement with Monotype Imaging Inc. • Helvetica, Palatino and Times are registered trademarks of Linotype-Hell AG. • ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC ZapfDingbats are registered trademarks of International Type-face Corporation. • UFST™ MicroType® fonts by Monotype Imaging Inc. are installed in this machine. • This machine contains the NF module developed by ACCESS Co., Ltd. • This machine contains the software having modules developed by Independent JPEG Group. • This product contains NetFront Browser of ACCESS CO., LTD. • ACCESS, ACCESS logo and NetFront are trademarks or registered trademarks of ACCESS CO., LTD.in the United States, Japan and other countries. • © 2009 ACCESS CO., LTD. All rights reserved. • This software is based in part on the work of the Independent JPEG Group. All other brands and product names are registered trademarks or trademarks of their respective companies. The designations ™ and ® will not be used in this Operation Guide. OPERATION GUIDE xxi GPL Firmware of this machine is using in part the GPL applied codes (www.fsf.org/copyleft/gpl.html). Please access “http://www.kyoceramita.com/gpl” for more information on how to make GPL applied codes available. Open SSL License Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3 All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http:/ /www.openssl.org/)” 4 The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected]. 5 Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project. 6 Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)” THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. xxii OPERATION GUIDE Original SSLeay License Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved. This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]). Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1 Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3 All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes cryptographic software written by Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-). 4 If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgment: “This product includes software written by Tim Hudson ([email protected])” THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.] OPERATION GUIDE xxiii Monotype Imaging License Agreement 1 Software shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as well as the UFST Software. 2 You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and versions of letters, numerals, characters and symbols (Typefaces) solely for your own customary business or personal purposes at the address stated on the registration card you return to Monotype Imaging. Under the terms of this License Agreement, you have the right to use the Fonts on up to three printers. If you need to have access to the fonts on more than three printers, you need to acquire a multiuser license agreement which can be obtained from Monotype Imaging. Monotype Imaging retains all rights, title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement. 3 To protect proprietary rights of Monotype Imaging, you agree to maintain the Software and other proprietary information concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces. 4 You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy. You agree that any such copy shall contain the same proprietary notices as those appearing on the original. 5 This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License may be terminated by Monotype Imaging if you fail to comply with the terms of this License and such failure is not remedied within thirty (30) days after notice from Monotype Imaging. When this License expires or is terminated, you shall either return to Monotype Imaging or destroy all copies of the Software and Typefaces and documentation as requested. 6 You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software. 7 Monotype Imaging warrants that for ninety (90) days after delivery, the Software will perform in accordance with Monotype Imaging-published specifications, and the diskette will be free from defects in material and workmanship. Monotype Imaging does not warrant that the Software is free from all bugs, errors and omissions. The parties agree that all other warranties, expressed or implied, including warranties of fitness for a particular purpose and merchantability, are excluded. 8 Your exclusive remedy and the sole liability of Monotype Imaging in connection with the Software and Typefaces is repair or replacement of defective parts, upon their return to Monotype Imaging. In no event will Monotype Imaging be liable for lost profits, lost data, or any other incidental or consequential damages, or any damages caused by abuse or misapplication of the Software and Typefaces. 9 Massachusetts U.S.A. law governs this Agreement. 10 You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written consent of Monotype Imaging. 11 Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2). 12 You acknowledge that you have read this Agreement, understand it, and agree to be bound by its terms and conditions. Neither party shall be bound by any statement or representation not contained in this Agreement. No change in this Agreement is effective unless written and signed by properly authorized representatives of each party. By opening this diskette package, you agree to accept the terms and conditions of this Agreement. xxiv OPERATION GUIDE Energy Saving Control Function The device comes equipped with a Sleep where printer and fax functions remain in a waiting state but power consumption is still reduced to a minimum when there is no activity with the device within a set amount of time since the device was last used. Sleep The device automatically enters Sleep when 8 minutes have passed since the device was last used. The amount of time of no activity that must pass before Sleep is activated may be lengthened. For more information see Sleep and Auto Sleep on page 2-9. Automatic 2-Sided Copy Function This device includes 2-sided copying as a standard function. For example, by copying two 1-sided originals onto a single sheet of paper as a 2-sided copy, it is possible to lower the amount of paper used. For more information see Duplex Copying on page 3-11. Paper Recycling This device supports the recycled paper which reduces the load on the environment. Your sales or service representative can provide information about recommended paper types. Energy Star (ENERGY STAR®) Program We have determined as a participating company in the International Energy Star Program that this product is compliant with the standards laid out in the International Energy Star Program. OPERATION GUIDE xxv About this Operation Guide This Operation Guide contains the following chapters. Chapter 1 - Part Names Identifies machine parts and operation panel keys. Chapter 2 - Preparation before Use Explains adding paper, placing originals, connecting the machine, and necessary configurations before first use. Chapter 3 - Basic Operation Describes the procedures for basic copying, printing and scanning. Chapter 4 - Copying Functions Describes the functions you can use when copying. Chapter 5 - Sending Functions Describes the functions you can use when sending originals. Chapter 6 - Document Box Provides a basic guide to using document boxes. Chapter 7 - Status / Job Cancel Explains how to check the job status and job history and how to cancel jobs being printed or waiting to print. Also explains how to check the remaining paper and device status and how to cancel fax transmission Chapter 8 - Default Setting (System Menu) Describes the System Menu options for general machine operation. Chapter 9 - Maintenance Describes cleaning and toner replacement. Chapter 10 - Troubleshooting Explains how to handle error messages, paper jams and other problems. Chapter 11 - Management Explains user login administration and job accounting. Appendix Explains how to enter characters, and lists the machine specifications. Introduces the convenient optional equipment available for this machine. Provides information on media types and paper sizes. Also includes a glossary of terms. xxvi OPERATION GUIDE Conventions in This Guide The following conventions are used depending on the nature of the description. Convention Description Example Bold Indicates the operation panel keys or a computer screen. Press the Start key. [Regular] Indicates the touch panel keys. Press [OK]. Italic Indicates a message displayed on the touch panel. Ready to copy is displayed. Used to emphasize a key word, phrase or references to additional information. For more information refer to Sleep and Auto Sleep on page 2-9. Note Indicates supplemental information or operations for reference. NOTE: Important Indicates items that are required or prohibited so as to avoid problems. IMPORTANT: Indicates what must be observed to prevent injury or machine breakdown and how to deal with it. CAUTION: Caution Description of Operation Procedure In this Operation Guide, continuous operation of the keys on the touch panel is as follows: Actual procedure Press [Copy]. Press [Next] of Quick Setup. Press [ ] twice. Press [Change] of Original Image. OPERATION GUIDE Description in this Operation Guide Press [Copy], [Next] of Quick Setup, [ ] twice, and then [Change] of Original Image. xxvii Originals and Paper Sizes This section explains the notation used in this guide when referring to sizes of originals or paper sizes. As with A4, B5 and Letter, which may be used either in the horizontal or vertical direction, horizontal direction is indicated by an additional letter R in order to indicate the orientation of the original/paper. Placement direction Vertical direction B A Indicated size * A4, B5, A5, B6, A6, 16K, Letter, Statement B A Original Paper For the originals/paper, dimension A is longer than B. Horizontal direction B A A4-R, B5-R, A5-R, B6-R, A6-R, 16KR, Letter-R, Statement-R B A Original Paper For the originals/paper, dimension A is shorter than B. * The size of the original/paper that can be used depends on the function and source tray. For further details, refer to the page detailing that function or source tray. Icons on the Touch Panel The following icons are used to indicate originals and paper placement directions on the touch panel. Placement direction Originals Paper Vertical direction Horizontal direction xxviii OPERATION GUIDE 1 Part Names This chapter identifies the machine parts and operation panel keys. • • Operation Panel ..................................................................................1-2 Machine ..............................................................................................1-4 OPERATION GUIDE 1-1 Part Names Operation Panel Displays the Status/Job Cancel screen. Displays the System Menu. Displays number of sheets printed and number of pages scanned. Displays help guidance. Blinks during printing operation. Blinks while data is transmitted. Displays the Copy screen. Displays the screen for sending. You can also change this to show the address book screen. Switches the touch panel display to enlarged display in the Copy screen or Send screen. Displays the Document Box screen. Displays the Application screen. Displays the Program screen. 1-2 OPERATION GUIDE Part Names Blinks while data is received. 1 Blinks while the machine is accessing the hard disk, fax memory or USB memory (general-purpose item). Lights or blinks when an error occurs and a job is stopped. Displays the Interrupt Copy screen. Ends operation (logs out) on the Administration screen. Puts the machine into Sleep. Recovers from Sleep if in Sleep. Lit when the machine's main power is on. Numeric keys. Enter numbers and symbols. Clears entered numbers and characters. Recalls already registered destinations and programs for sending. Finalizes numeric key entry, and finalizes screen during setting of functions. Operates linked with the on-screen [OK]. OPERATION GUIDE Returns settings to their default states. Cancels or pauses the printing job in progress. Starts copying and scanning operations and processing for setting operations. 1-3 Part Names Machine 1 Original Cover (Option) 2 Original Size Indicator Plates 3 Clip Holder 4 Slit Glass 5 Attention Indicator... Lights or blinks when an error occurs and a job is stopped 6 Receive Indicator... Blinks while data is received 7 Left Cover 1 8 Left Cover 1 Lever 9 Left Cover 2 10 Left cover 2 Handle 11 Platen 12 Operation Panel 13 Cassette 1 14 Cassette 2 1-4 OPERATION GUIDE Part Names 1 15 Toner Container Stopper 16 Toner Container 17 Waste Toner Box 18 Paper Feed Unit (A2) 19 Paper Feed Unit Cover (A3) 20 Green Knob OPERATION GUIDE 1-5 Part Names OP 2 DP A2 B OP 1 21 USB Memory Slot (A1) 22 Front Cover 23 Paper Width Adjusting Tab 24 Paper Length Guide 25 Top Tray 26 Main Power Switch 27 Paper Width Guide 28 Multi Purpose Tray 29 Option Interface Slot (OPT2) 30 USB Memory Slot (A2) 31 USB Interface Connector (B1) 32 Network Interface Connector 33 Option Interface Slot (OPT1) 1-6 OPERATION GUIDE 2 Preparation before Use This chapter explains the preparations before using this equipment for the first time as well as the procedures for loading paper and originals. • • • • • • • • • • • • • • Check the Accessories .......................................................................2-2 Determining the Connection Method and Preparing Cables...............2-3 Connecting Cables..............................................................................2-5 Power On/Off ......................................................................................2-7 Sleep and Auto Sleep .........................................................................2-9 Adjusting the Operation Panel Angle ................................................2-10 Switching the Language for Display [Language]...............................2-10 Setting Date and Time ......................................................................2-11 Network Setup (LAN Cable Connection) ..........................................2-12 Installing Software.............................................................................2-15 Embedded Web Server (Settings for E-mail) ....................................2-16 Sending E-mail..................................................................................2-17 Loading Paper...................................................................................2-19 Loading Originals ..............................................................................2-30 OPERATION GUIDE 2-1 Preparation before Use Check the Accessories Check that the following accessories are included. • Operation Guide (This Guide) • CD-ROM (Product Library) Documents Contained in the Included CD-ROM The following documents are contained in the included CD-ROM (Product Library). Refer to them as necessary. Documents Embedded Web Server Operation Guide Printer Driver User Guide Network FAX Driver Operation Guide TWAIN/WIA Driver Operation Guide Network Tool for Direct Printing Operation Guide Network Print Monitor User Guide Scan to SMB (PC) Setup Guide PRESCRIBE Commands Technical Reference PRESCRIBE Commands Command Reference Data Security Kit (E) Operation Guide Fax System (S) Operation Guide 2-2 OPERATION GUIDE Preparation before Use Determining the Connection Method and Preparing Cables Check the method to connect the equipment to a PC or network, and prepare the necessary cables. 2 Connection Example Determine the method to connect the equipment to a PC or network by referring to the illustration below. Connecting a scanner to your PC network with a network cable (100BASE-TX or 10BASE-T) Embedded Web Server Administrator’s PC Network Network settings, Scanner default settings, User and destination registration Send E-mail Sends the image data of scanned originals to the desired recipient as a file attached to an E-mail message. MFP Printing Network USB Saves the scanned image as a data file on your PC. Network Network Network Network FAX (Option) Send SMB Send FTP Sends the scanned image as a data file on the FTP. FAX (Option) TWAIN Scanning FAX Network WIA Scanning Network OPERATION GUIDE TWAIN and WIA are standardized interface for communication between software applications and image acquisition devices. 2-3 Preparation before Use Preparing Necessary Cables The following interfaces are available to connect the equipment to a PC. Prepare the necessary cables according to the interface you use. Available Standard Interfaces Function Necessary Cable Printer/Scanner /Network FAX* Network interface LAN (10Base-T or 100Base-TX, Shielded) Printer USB interface USB2.0 compatible cable (Hi-Speed USB compliant, Max. 5.0 m, Shielded) * 2-4 Interface Function available when using optional fax kit. For details on Network FAX, refer to the Fax Kit Operation Guide. OPERATION GUIDE Preparation before Use Connecting Cables Connecting LAN Cable (Optional) 2 Follow the steps below to connect a LAN cable to the machine. 1 When the machine is powered up, first press the Power key on the operation panel. Check that the Power indicator and the memory indicator are off. After this, turn off the main power switch. 2 Connect the LAN cable to the network interface located on right side of the body. 3 Connect the other end of the cable to the hub. 4 Configure the network. For details, refer to Network Setup (LAN Cable Connection) on page 2-12. Check that the indicators are off. DP A2 B1 PT 1 OPERATION GUIDE 2-5 Preparation before Use Connecting USB Cable Follow the steps below to connect a USB cable to the machine. 1 When the machine is powered up, first press the Power key on the operation panel. Check that the Power indicator and the memory indicator are off. After this, turn off the main power switch. 2 Connect the USB cable to the appropriate interface located on the right side of the body. 3 Connect the other end of the cable to the PC. Check that the indicators are off. DP A2 B1 OP T1 Connecting the Power Cable Connect one end of the supplied power cable to the machine and the other end to a power outlet. IMPORTANT: Only use the power cable that comes with the machine. 2-6 OPERATION GUIDE Preparation before Use Power On/Off Power On 2 When the main power indicator is lit... Press the Power key. When the main power indicator is off... Open the main power switch cover and turn the main power switch on. NOTE: If the optional Data Security Kit is installed, a message might display indicating the security function is being activated and time may be taken to start up when the power is turned on. IMPORTANT: When turning off the main power switch, do not turn on the main power switch again immediately. Wait more than 5 seconds, and then turn on the main power switch. OPERATION GUIDE 2-7 Preparation before Use Power Off Before turning off the main power switch, press the Power key on the operation panel to off. Make sure that the Power key and the memory indicator are off before turning off the main power switch. CAUTION: The hard disk may be operating when the Power key or Memory indicator is lit or blinking. Turning off the main power switch while the hard disk is operating may cause damage. Make sure that the indicators are off. In case of not using the machine for an extended period of time CAUTION: If this machine will be left unused for an extended period (e.g. overnight), turn it off at the main power switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power plug from the outlet as a safety precaution. If the optional Fax kit is installed, note that turning the machine off at the main power switch disables fax transmission and reception. CAUTION: Remove paper from the cassettes and seal it in the paper storage bag to protect it from humidity. 2-8 OPERATION GUIDE Preparation before Use Sleep and Auto Sleep Sleep To enter Sleep, press the Power key. Touch panel and all indicators on the operation panel will go out to save a maximum amount of power except the Main Power indicator. This status is referred to as Sleep. If print data is received during Sleep, the print job is performed while the touch panel remains unlit. When using the optional fax, received fax data is printed out while the operation panel also remains unlit. To resume, press the Power key. The machine will be ready within 15 seconds. Note that ambient environmental conditions, such as ventilation, may cause the machine to respond more slowly. Auto Sleep Auto Sleep automatically switches the machine into Sleep if left idle for a preset time. The default preset time is 8 minutes. OPERATION GUIDE 2-9 2 Preparation before Use Adjusting the Operation Panel Angle Adjust the angle of the operation panel in two as shown by releasing the operation panel lock lever. Switching the Language for Display [Language] Select the language displayed on the touch panel. Use the procedure below to select the language. Common Settings - Language 1 Press the System Menu key. 2 Press [Common Settings] and then [Change] of Language. 3 Press the key for the language you want to use. 4 Press [OK]. Set the language to use for the touch panel display. English Deutsch Français Nederlands ǸțșșȒȐȑ Português Español Italiano Cancel Status OK 08/08/2009 10:10 The touch panel language will be changed. 2-10 OPERATION GUIDE Preparation before Use Setting Date and Time Follow the steps below to set the local date and time at the place of installation. When you send an E-mail using the transmission function, the date and time as set here will be printed in the header of the E-mail message. Set the date, time and time difference from GMT of the region where the machine is used. NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. If user login administration is disabled, the user authentication screen appears. Enter a login user name and password, and press [Login]. Refer to Adding a User on page 11-5 for the default login user name and password. Be sure to set the time difference before setting the date and time. If you change Date/Time setting, trial functions will be unavailable. For details, refer to Optional Functions on page 8-75. Date/Timer - Time Zone 1 Press the System Menu key. 2 Press [ ], [Date/Timer] and then [Change] of Time Zone. 3 Select the region. Set time zone. Select the location nearest you. NOTE: Press [ Time Zone ] or [ ] to view the next region. -12:00 International Date Line West 4 -11:00 Midway Island, Samoa -10:00 Hawaii Press [Off] or [On] of Summer Time and press [OK]. ummer Time 1/13 Off -09:00 Alaska -08:00 Pacific Time (US & Canada) NOTE: If you select a region that does not utilize summer time, the summer time setting screen will not appear. On -07:00 Arizona Cancel OK Status 08/08/2009 10:10 Date/Timer - Date/Time 5 Press [Change] of Date/Time. 6 Set the date and time. Press [+] or [–] in each setting. 7 Press [OK]. Set the date and time. 2008 Y ar 10 10 10 M th 10 31 Day S Cancel Status OPERATION GUIDE nd OK 08/08/2009 10:10 2-11 2 Preparation before Use Network Setup (LAN Cable Connection) The machine is equipped with network interface, which is compatible with network protocols such as TCP/IP (IPv4), TCP/IP (IPv6), IPX/SPX, NetBEUI, IPSec, and AppleTalk. It enables network printing on the Windows, Macintosh, UNIX, NetWare and other platforms. This section explains the TCP/IP (IPv4) Setup and AppleTalk Setup procedures. For other network settings, refer to the Network Setup on 8-64. • TCP/IP (IPv4) Setup...2-12 • AppleTalk Setup...2-14 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. If user login administration is disabled, the user authentication screen appears. Enter a login user name and password, and press [Login]. Refer to Adding a User on page 11-5 for the default login user name and password. TCP/IP (IPv4) Setup (by Entering IP Addresses) Set up TCP/IP to connect to the Windows network. Set the IP addresses, subnet masks, and gateway addresses. The default settings are "TCP/IP Protocol: On, DHCP: On, Bonjour: Off, Auto-IP: On". NOTE: Prior to the IP address entries, obtain permission from the network administrator. Use the procedure below. System - IPv4 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Change] of TCP/IP. 4 Press [On] and then press [OK]. 5 Press [Change] of IPv4. 6 Press [DHCP]. 7 Press [Off] of DHCP and then press [OK]. 8 Press [Bonjour]. Set TCP/IP (IPv4). On DHCP IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Default Gateway 0.0.0.0 On Off Auto-IP Bonjour Cancel Status 2-12 OK 08/08/2009 10:10 OPERATION GUIDE Preparation before Use 9 Press [Off] of Bonjour and then press [OK]. 10 Press [IP Address] and enter the address using the numeric keys. 11 Press [Subnet Mask] and enter the address using the numeric keys. 12 Press [Default Gateway] and enter the address using the numeric keys. 13 Check if all the address entries are correct and press [OK]. 14 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. DHCP Settings Select whether or not to use the DHCP server. The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Change] of TCP/IP. 4 Press [On] and then press [OK]. 5 Press [Change] of IPv4. 6 Press [DHCP]. 7 Press [On] or [Off] of DHCP and then press [OK]. 8 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. Bonjour Settings Select whether or not to use Bonjour. The default setting is Off. Use the procedure below. OPERATION GUIDE 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 2-13 2 Preparation before Use 3 Press [Change] of TCP/IP. 4 Press [On] and then press [OK]. 5 Press [Change] of IPv4. 6 Press [Bonjour]. 7 Press [On] or [Off] of Bonjour and then press [OK]. 8 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. Auto-IP Settings Select whether or not to use Auto-IP. The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Change] of TCP/IP. 4 Press [On] and then press [OK]. 5 Press [Change] of IPv4. 6 Press [Auto-IP]. 7 Press [On] or [Off] of Auto-IP and then press [OK]. 8 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. AppleTalk Setup Select the Apple Talk network connection. The default setting is On. Use the procedure below. 2-14 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Change] of AppleTalk. 3 Press [On] or [Off]. OPERATION GUIDE Preparation before Use 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. Installing Software Install appropriate software on your PC from the included Product Library CD-ROM (Product Library) if you want to use the printer function of this machine or perform TWAIN / WIA transmission or FAX transmission from your PC. NOTE: Installation on Windows XP, Windows 2000, Server 2003 and Windows Vista must be done by a user logged on with administrator privileges. Plug and Play is disabled on this device when in Sleep. Wake the device from Sleep before continuing. See Sleep and Auto Sleep on page 2-9. OPERATION GUIDE 2-15 2 Preparation before Use Embedded Web Server (Settings for E-mail) Embedded Web Server is a tool used for tasks such as verifying the operating status of the machine and changing the settings for security, network printing, E-mail transmission and advanced networking. NOTE: Here, information on the FAX settings has been omitted. For more information on using the FAX, refer to the Fax Kit Operation Guide. The procedure for accessing Embedded Web Server is explained below. 1 Launch your Web browser. 2 In the Address or Location bar, enter the machine’s IP address. E.g.) http://192.168.48.21/ The web page displays basic information about the machine and Embedded Web Server as well as their current status. 3 Select a category from the navigation bar on the left of the screen. The values for each category must be set separately. If restrictions have been set for Embedded Web Server, enter the correct user name and password to access pages other than the startup page. For details, refer to the Embedded Web Server Operation Guide. 2-16 OPERATION GUIDEEmbeddedE Preparation before Use Sending E-mail Specifying the SMTP settings allows you to send images loaded onto this machine as E-mail attachments. To use this function, this machine must be connected to a mail server using the SMTP protocol. 2 Before sending images loaded onto this machine as E-mail attachments, check the following: • • • The network environment used to connect this machine to the mail server A full-time connection via a LAN is recommended. SMTP Settings Use Embedded Web Server to register the IP address or host name of the SMTP server. If limits have been set on the size of E-mail messages, it may not be possible to send very large E-mails. The procedure for specifying the SMTP settings is explained below. 1 Click Advanced -> SMTP -> General. OPERATION GUIDE 2-17 Preparation before Use 2 Enter the correct settings in each field. The settings to be specified in the SMTP settings screen are shown below. Item SMTP Protocol Enables or disables SMTP protocol. To use E-mail, this protocol must be enabled. SMTP Port Number Set the SMTP Port Number or use the SMTP default port 25. SMTP Server Name Enter the SMTP server IP address or its name. The maximum length of the SMTP server name and IP address is 64 characters. If entering the name, a DNS server address must also be configured. The DNS server address may be entered on the TCP/IP General tab. SMTP Server Timeout Set the amount of time to wait before time-out in seconds. Authentication Protocol Enables or disables the SMTP authentication protocol or sets POP before SMTP as the protocol. The SMTP authentication supports Microsoft Exchange 2000. Authenticate as Authentication can be set from three POP3 accounts or you can choose a different account. Login User Name When Other is selected for Authenticate, the login user name set here will be used for SMTP authentication. The maximum length of the login user name is 64 characters. Login Password When Other is selected for Authenticate, the password set here will be used for authentication. The maximum length of the login password is 64 characters. POP before SMTP Timeout Test 3 Description Set the amount of time to wait before time-out in seconds when you have selected POP before SMTP as the Authentication Protocol. This will test if the SMTP connection can be successfully established. E-mail Size Limit Enter the maximum size of E-mail that can be sent in kilobytes. When the value is 0, the limitation for E-mail size is disabled. Sender Address Enter the E-mail address of the person responsible for the machine, such as the machine administrator, so that a reply or non-delivery report will go to a person rather than to the machine. The sender address must be entered correctly for SMTP authentication. The maximum length of the sender address is 128 characters. Signature Enter the signature. The signature is free form text that will appear at the end of the E-mail body. It is often used for further identification of the machine. The maximum length of the signature is 512 characters. Domain Restriction Enter the domain names that can be permitted or rejected. The maximum length of the domain name is 32 characters. You can also specify E-mail addresses. Click Submit. 2-18 OPERATION GUIDE Preparation before Use Loading Paper Paper can be loaded standardly in the two cassettes and the multi purpose tray. A paper feeder is also available as an option (refer to Optional Equipment on Appendix-2). Before Loading Paper When you open a new package of paper, fan the sheets to separate them slightly prior to loading in the following steps. 1 Bend the whole set of sheets to swell them in the middle. 2 Hold the stack at both ends and stretch it while keeping the entire stack risen. 3 Raise the right and left hands alternately to create a gap and feed air between the paper. 4 Finally, align the paper on a level, flat table. If the paper is curled or folded, straighten it before loading. Paper that is curled or folded may cause a jam. CAUTION: If you copy onto used paper (paper already used for copying), do not use paper that is stapled or clipped together. This may damage the machine or cause poor image quality. NOTE: If printouts are curled or not neatly stapled, turn the stack in the cassette upside down. Avoid exposing opened paper to high temperatures and high humidity as dampness can be a cause of problems. Seal any remaining paper after loading in the multi purpose tray or cassettes back in the paper storage bag. If the machine will not be used for a prolonged period, protect all paper from humidity by removing it from the cassettes and sealing it in the paper storage bag. NOTE: If you use special paper such as letterhead, paper with holes or paper with pre-prints like logo or company name, refer to the Paper on Appendix-13. OPERATION GUIDE 2-19 2 Preparation before Use Loading Paper in the Cassettes The 2 standard cassettes will each hold plain paper, recycled paper or color paper. Cassette holds up to 500 sheets (80 g/m2). The following paper sizes are supported: Ledger, Legal, Oficio II, 8.5×13.5", Letter, Letter-R, Statement, A3, B4, A4, A4-R, B5, B5-R, A5, Folio, 8K, 16K, and 16K-R. IMPORTANT: • You should not use inkjet printer paper or any paper with a special surface coating. (Such paper may cause paper jams or other faults.) • When using media types other than plain paper (such as recycled or colored paper), always specify the media type setting. (Refer to Specifying Paper Size and Media Type for the Cassettes on page 2-26) The cassettes can hold paper with weights up to 105 g/m2. • Do not load paper that is heavier than 106 g/m2 in the cassettes. Use the multi purpose tray for paper that is heavier than 106 g/m2. 1 Pull the cassette out toward you until it stops. NOTE: Do not pull out more than one cassette at a time. 2 Using the paper length guide, move the plate to fit the paper. When loading A4 or smaller paper into cassette 1, lift up the paper length guide. For B4 or larger paper, lower the paper length guide. NOTE: Paper sizes are marked on the cassette. 3 2-20 Holding the paper width adjusting tab, move the paper width guides to fit the paper. OPERATION GUIDE Preparation before Use NOTE: Paper sizes are indicated on the cassettes. To change between inch size and metric size (A, B sizes), follow the steps below to adjust the size switch. A B 1. Holding the paper width adjusting tab, move the paper width guide to a position other than that of the paper. 2. Turn the size switch A 90°. > 3. Move the size lever B up (C) or down (I). C:metric size (centimeters) (A, B sizes) I:inch size 4. Turn the size switch 90°to lock it. > 4 Align the paper flush against the left side of the cassette. IMPORTANT: OPERATION GUIDE • Before loading the paper, be sure that it is not curled or folded. Paper that is curled or folded may cause paper jams. • Ensure that the loaded paper does not exceed the level indicator (see illustration below). • When loading the paper, keep the side that was closest the package seal facing up. • The paper length and width guides must be adjusted to the paper size. Loading the paper without adjusting these guides may cause skewed feeding and paper jams. • Be sure that the paper length and width guides rest securely against the paper. If there is a gap, readjust the guides to fit the paper. 2-21 2 Preparation before Use 5 Insert the appropriate paper size card in the slot to indicate the size of the paper inside. 6 Gently push the cassette back in. NOTE: If the machine will not be used for a prolonged period, protect all paper from humidity by removing it from the cassettes and sealing it in the paper storage bag. 7 Select the media type (plain, recycled, etc.) loaded in the cassette. (Refer to Specifying Paper Size and Media Type for the Cassettes on page 2-26.) Loading Paper in the Multi Purpose Tray The multi purpose tray will hold up to 200 sheets of plain paper (80 g/m2). The multi purpose tray accepts paper sizes from A3 to A6 and Hagaki and from Ledger to Statement-R, 8K, 16K and 16K-R. Be sure to use the multi purpose tray when you print on any special paper. IMPORTANT: When using media types other than plain paper (such as recycled or colored paper), always specify the media type setting. (Refer to Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-28.) If you are using a paper weight of 106 g/m2 or more, set the media type to Thick. The capacity of the multi purpose tray is as follows. • Hagaki: 80 sheets • OHP film: 25 sheets • Envelope DL, Envelope C5, Envelope #10 (Commercial #10), Monarch, Youkei 4, Youkei 2: 20 sheets NOTE: When you load custom size paper, enter the paper size by referring to Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-28. When you use special paper such as transparencies or thick paper, select the media type by referring to Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-28. 2-22 OPERATION GUIDE Preparation before Use 1 Open the multi purpose tray. 2 2 Adjust the paper width guides to the width of the paper. 3 Insert the paper along the paper width guides into the tray until it stops. IMPORTANT: Keep the side that was closest the package seal facing up. Curled paper must be uncurled before use. Straighten the top edge if it is curled. When loading paper into the multi purpose tray, check that there is no paper left over in the tray from a previous job before loading the paper. If there is just a small amount of paper left over in the multi purpose tray and you want to add more, first remove the left-over paper from the tray and include it with the new paper before loading the paper back into the tray. OPERATION GUIDE 2-23 Preparation before Use Loading Envelopes Up to 20 envelopes may be loaded in the multi purpose tray. Acceptable envelope sizes are as follows. Acceptable Envelope Size Youkei 2 162×114 (mm) Youkei 4 235×105 (mm) Monarch 3 7/8"×7 1/2" Envelope #10 (Commercial #10) 4 1/8"×9 1/2" Envelope DL 110×220 (mm) Envelope C5 162×229 (mm) 1 Open the multi purpose tray. 2 Adjust the paper width guides to the width of the envelope. 3 For landscape form envelopes, close the flap. Insert the envelope all the way along the width guides, keeping the printing side face-up and the edge with the flap facing towards you. For portrait form envelopes, close the flap. Insert the envelope all the way along the width guides, keeping the printing side face-up and the edge with the flap facing the insertion slot. 2-24 OPERATION GUIDE Preparation before Use When you load envelopes or cardstock in the multi purpose tray 2 Load envelope with the print side facing up. Landscape form envelopes Portrait form envelopes Cardstock (Hagaki) Return postcard (Oufuku Hagaki) NOTE: Use unfolded return postcard (Oufuku Hagaki). IMPORTANT: How to load envelopes (orientation and facing) will differ depending on the type of envelope. Be sure to load it in correctly, otherwise printing may be done in the wrong direction or on the wrong face. NOTE: When you load envelopes in the multi purpose tray, select the envelope type by referring to Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-28. OPERATION GUIDE 2-25 Preparation before Use Specifying Paper Size and Media The default paper size setting for cassettes 1 and 2, for multi purpose tray and for the optional paper feeder (cassettes 3 and 4) is [Auto], and the default media type setting is [Plain]. To fix the type of paper to be used in cassettes, specify the paper size and media type setting. (Refer to Specifying Paper Size and Media Type for the Cassettes on page 2-26.) To fix the type of paper to be used in multi purpose tray, specify the paper size setting. (Refer to Specifying Paper Size and Media Type for the Multi Purpose Tray on page 2-28.) Specifying Paper Size and Media Type for the Cassettes To fix the type of paper to be used in cassettes 1 or 2 or the optional paper feeder (cassettes 3 and 4), specify the paper size. Also, you use a media type other than plain paper, specify the media type setting. Selection Item Paper Size Auto Paper size is automatically detected and selected. Select whether the paper is in Metric size or in Inch size. Standard Sizes 1 Select from the standard sizes. Selectable paper sizes are as follows. Inch size: Ledger, Letter-R, Letter, Legal, Statement-R, 8.5×13.5" and Oficio II Metric size: A3, B4, A4, A4-R, B5, B5-R, A5-R, and Folio Standard Sizes 2 Select from the standard sizes not included in Standard Sizes 1. Selectable paper sizes are as follows. Inch size: A3, B4, A4, A4-R, B5, B5-R, A5-R, Folio, 8K, 16K-R and 16K Metric size: Ledger, Letter-R, Letter, Legal, Statement-R, 8.5×13.5", Oficio II, 8K, 16K-R and 16K Media Type * ** Selectable Size/Type Plain (105 g/m2 or less), Rough, Vellum (64 g/m2 or less), Recycled, Preprinted**, Bond*, Color, Prepunched**, Letterhead**, High Quality and Custom 1~8* To change to a media type other than Plain, refer to Paper Weight on page 8-7. When the paper weight settings shown below are selected, the media indicated for each setting cannot be selected. • Custom 1 to 8: Heavy 1, Heavy 2, Heavy 3, or Extra Heavy To print on preprinted or prepunched paper or on letterhead, refer to Special Paper Action on page 8-10. NOTE: If the optional FAX kit is installed, the available media types for printing received faxes are as shown below. Plain, Recycled, Bond, Color, High Quality, Rough and Custom 1 to 8 2-26 OPERATION GUIDE Preparation before Use 1 Press the System Menu key. 2 2 Press [Common Settings], [Next] of Original / Paper Settings, [Next] of Cassette Setting. 3 Cassette Setting, select one of [Cassette 1] to [Cassette 4] and press [Next]. Then press [Change] of Paper Size. NOTE: [Cassette 3] and [Cassette 4] are shown when the optional paper feeder is installed. 4 For automatic detection of the paper size, press [Auto] and select [Metric] or [Inch] as the unit. To select the paper size, press [Standard Sizes 1] or [Standard Sizes 2] and select the paper size. Common Settings - Paper Size Set cassette paper size. Auto Ledger Letter Letter Standard Sizes 1 Statement 8.5x13.5" OficioII Legal Standard Sizes 2 Cancel OK Status 08/08/2009 10:10 Common Settings - Media Type Select type of paper in Cassette 1. Plain Rough Recycled Preprinted Prepunched Letterhead Custom 1 Custom 2 Custom 3 Custom 6 Custom 7 Custom 8 5 Press [OK]. The previous screen reappears. 6 Press [Change] of Media Type and select the media type. Then press [OK]. Vellum Bond Color High Quality Custom 4 Custom 5 Cancel Status OPERATION GUIDE OK 08/08/2009 10:10 2-27 Preparation before Use Specifying Paper Size and Media Type for the Multi Purpose Tray To fix the type of paper to be used in the multi purpose tray, specify the paper size.When using other than a plain paper, specify the media type. Item Paper Size Auto Paper size is automatically detected and selected. Select whether the paper is in Metric size or in Inch size. Standard Sizes 1 Select from the standard sizes. Selectable paper sizes are as follows. Inch size: Ledger, Letter-R, Letter, Legal, Statement-R, Executive, 8.5×13.5" and Oficio II Metric size: A3, A4-R, A4, A5-R, A6-R, B4-R, B5-R, B5, B6-R and Folio Standard Sizes 2 Select from the standard sizes not included in Standard Sizes 1. Selectable paper sizes are as follows. Inch size: A3, A4-R, A4, A5-R, A6-R B4-R, B5-R, B5, B6-R, Folio, 8K, 16K-R and 16K Metric size: Ledger, Letter-R, Letter, Legal, Statement-R, Executive, 8.5×13.5", Oficio II, 8K, 16K-R and 16K Others Select from special standard sizes and custom sizes. Selectable paper sizes are as follows. ISO B5, Envelope #10 (Commercial #10), Envelope #9 (Commercial #9), Envelope #6 (Commercial #6 3/4), Envelope Monarch, Envelope DL, Envelope C5, Envelope C4, Hagaki, Oufuku Hagaki, Youkei 4, Youkei 2 Size Entry Enter the size not included in the standard size. Selectable paper sizes are as follows. Inch size X (Horizontal): 5.83~17" (in 0.01" increments), Y (Vertical): 3.86~11.69" (in 0.01" increments) Metric size X (Horizontal): 148~432 mm (in 1mm increments), Y (Vertical): 98~297 mm (in 1mm increments) Media Type * ** Description Selectable media types are as follows. Plain (105g /m2 or less), Rough, Transparency, Vellum (64 g/m2 or less), Labels, Recycled, Preprinted**, Bond, Cardstock, Color, Prepunched**, Letterhead**, Envelope, Thick (91 g/m2 and more), High Quality and Custom 1~8 To change to a media type other than Plain, refer to Paper Weight on page 8-7. To print on preprinted or prepunched paper or on letterhead, refer to Special Paper Action on page 8-10. NOTE: If the optional FAX kit is installed and the multi purpose tray is used to print a received FAX, the available media types are as shown below. Plain, Recycled, Bond, Color, High Quality, Rough and Custom 1 to 8 2-28 OPERATION GUIDE Preparation before Use 1 Press the System Menu key. 2 Common Settings - Multi Purpose Tray Setting 2 Press [Common Settings], [Next] of Original / Paper Settings, [Next] of MP Tray Setting, and then [Change] of Paper Size. 3 For automatic detection of the paper size, press [Auto] and select [Metric] or [Inch] as the unit. Set the multi-purpose tray paper size. Auto Ledger Letter Letter Legal Standard Sizes 1 Statement Executive 8.5x13.5" OficioII To select the paper size, press any of [Standard Sizes 1], [Standard Sizes 2], [Others] or [Size Entry] and select the paper size. Standard Sizes 2 Others Size Entry Cancel OK Status 08/08/2009 10:10 If you have chosen [Size Entry], press [+] or [–] to enter X (horizontal) and Y (vertical) sizes. You may enter the size directly using the numeric keys by pressing [# Keys]. Common Settings - Paper Size Set the multi-purpose tray paper size. Auto X(5.83 - 17.00) Standard Sizes 1 17 Y(3.86 - 11.69) " 11 " Standard Sizes 2 Others # Keys # Keys Size Entry Cancel OK Status 08/08/2009 10:10 Common Settings - Media Type Select type of paper in Multi-Purpose Tray. Plain Transparency Rough Vellum Labels Recycled Preprinted Bond Cardstock Color Prepunched Letterhead Envelope Thick High Quality Custom 1 Custom 2 Custom 3 Custom 5 Custom 6 Custom 7 Custom 8 OPERATION GUIDE Press [OK]. The previous screen reappears. 5 Press [Change] of Media Type and select the media type. Then press [OK]. Custom 4 Cancel Status 4 OK 08/08/2009 10:10 2-29 Preparation before Use Loading Originals Follow the steps below to load originals for copying, sending or storing. Placing Originals on the Platen You may place books or magazines on the platen in addition to ordinary sheet originals. 1 Open the original cover. NOTE: If the optional document processor is installed, open the document processor. Before opening the document processor, be sure that there are no originals left on the original table or on the original eject table. Originals left on the original table or on the original eject table may fall off when the document processor is opened. Keep the document processor open if the original is 40 mm or thicker. 2 2-30 Place the original. Put the scanning side facedown and align it flush against the original size indicator plates with the back left corner as the reference point. OPERATION GUIDE Preparation before Use Original size indicator plates (Inch models) 2 (Metric models) 3 Close the original cover. IMPORTANT: Do not push the original cover forcefully when you close it. Excessive pressure may crack the platen glass. NOTE: Shadows may be produced around the edges and in the middle of open-faced originals. CAUTION: Do not leave the document processor open as there is a danger of personal injury. OPERATION GUIDE 2-31 Preparation before Use Loading Originals in the Document Processor The optional document processor automatically scans each sheet of multiple originals. Both sides of two-sided originals are scanned. Part Names of the Document Processor (1) (2) (3) (1) Original placement indicator (4) (4) Original table (5) (6) (7) (2) Top cover (3) Original width guides (5) Original eject table (6) Original stopper (7) Opening handle Originals Supported by the Document Processor The document processor supports the following types of originals. Weight 45 to 160 g/m2 (duplex: 50 to 120 g/m2) Size Maximum A3 to Minimum A5 Maximum Ledger to Minimum Statement-R Capacity Plain paper (80 g/m2), Colored paper, Recycled paper: 100 sheets (Mixed sized originals: 30 sheets) Thick paper (120 g/m2): 66 sheets Thick paper (160 g/m2): 50 sheets Art paper: 1 sheet High-quality paper (110 g/m2): 72 sheets Originals Not Supported by the Document Processor Do not use the document processor for the following types of originals. • Soft originals such as vinyl sheets • Transparencies such as OHP film • Carbon paper • Originals with very slippery surfaces • Originals with adhesive tape or glue • Wet originals • Originals with correction fluid which is not dried • Irregularly shaped (non-rectangular) originals • Originals with cut-out sections • Crumpled paper • Originals with folds (Straighten the folds before loading. Failure to do so may cause the originals to jam). • Originals bound with clips or staples (Remove the clips or staples and straighten curls, wrinkles or creases before loading. Failure to do so may cause the originals to jam). 2-32 OPERATION GUIDE Preparation before Use How to Load Originals IMPORTANT: Before loading originals, be sure that there are no originals left on the original eject table. Originals left on the original eject table may cause the new originals to jam. 2 1 Adjust the original width guides to fit the originals. 2 Place the originals. Put the side to be scanned (or the first side of two-sided originals) face-up. Slide the leading edge into the document processor as far as it will go. The original placement indicator will be lit. IMPORTANT: Confirm that the original width guides exactly fit the originals. If there is a gap, readjust the original width guides. The gap may cause the originals to jam. Ensure that loaded originals do not exceed the level indicator. Exceeding the maximum level may cause the originals to jam (see the figure). Originals with punched holes or perforated lines should be placed in such a way that the holes or perforations will be scanned last (not first). Original placement indicator The original placement indicator is lit or unlit depending on how originals are placed. Indications and their status are as follows. • • • OPERATION GUIDE Green (left indicator) lit: Original is placed properly. Green (left indicator) blinking: Original is not placed properly. Remove and place again. Red (right indicator) blinking: Original is jammed. Remove the jammed original and place it properly. 2-33 Preparation before Use 2-34 OPERATION GUIDE 3 Basic Operation This chapter explains the following operations. • • • • • • • • • • • • • • • Login/Logout .......................................................................................3-2 Enter key and Quick No. Search key ..................................................3-2 Touch Panel Display ...........................................................................3-4 Original Preview..................................................................................3-5 Copying...............................................................................................3-6 Printing - Printing from Applications..................................................3-21 Sending.............................................................................................3-23 Specifying Destination ......................................................................3-30 Using Document Box ........................................................................3-33 Basic Operation for Document Box...................................................3-35 Canceling Jobs .................................................................................3-42 Quick Setup Screen ..........................................................................3-43 Program (Copying and Sending) ......................................................3-46 Registering Shortcuts (Copy, Send, and Document Box Settings) ...3-46 Using the Internet Browser ...............................................................3-49 OPERATION GUIDE 3-1 Basic Operation Login/Logout If user login administration is enabled, it is necessary to enter the login user name and password to use the machine. NOTE: You will be unable to login if you forget your login user name or login password. In this event, login with administrator privileges and change your login user name or login password. Login 1 Enter login user name and password. Login to: Local Login User Name bcdef If the screen shown appears during operations, press [Login User Name]. Press [# Keys] to enter the login data using the numeric keys. # Keys Login Password ******** # Keys IC Card Login Check Counter Status Cancel Login 08/08/2009 10:10 2 Enter the login user name and press [OK]. NOTE: Refer to the Character Entry Method on Appendix-10 for details on entering characters. 3 Press [Login Password]. Press [# Keys] to enter the login data using the numeric keys. 4 Enter the password and press [OK]. 5 Check the login user name and password are correct, and press [Login]. NOTE: If Network Authentication is selected as the user authentication method, either Local or Network can be selected as the authentication destination. Logout To logout from the machine, press the Logout key to return to the login user name/password entry screen. 3-2 OPERATION GUIDE Basic Operation Enter key and Quick No. Search key This section explains how to use the Enter key and Quick No. Search key on the operation panel. Using the Enter ( ) key The Enter key works in the same way as keys displayed on the touch panel, such as [OK] and [Close]. The Enter symbol ( ) is displayed next to the keys whose operations are carried out by the Enter key (e.g. [ OK], [ Close]). The operation of the Enter key is explained below using copy paper selection as an example. For details of the procedure, refer to Paper Selection on page 4-4. 1 Copies Ready to copy. In the paper selection screen, press the key for the cassette containing the required paper size. Paper Selection Place original. Original Zoom Paper The Enter ( ) symbol appears on the [OK] on the touch panel, indicating that the Enter key performs the same action as [OK]. Auto : --: 100% : --- Letter Plain Letter Plain Ledger Plain MP Tray Setting 2 Letter Plain To copy using the selected paper, press the Enter key (or [OK]). Letter Plain Preview Cancel Add Shortcut OK Status 08/08/2009 Using the Quick No. Search ( 10:10 ) key Use the Quick No. Search keys to perform an action by simply entering a number directly using the numeric keys. For example, you can specify the speed dial for a transmission destination or recall a stored program by its program number. The Quick No. Search key performs the same action as the [No.] displayed on the touch panel. The use of the Quick No. Search key is explained below using an example in which a speed dial number is specified and used to select a destination. For more information on speed dialing, refer to Specifying Destination on page 3-30. Ready to send. Destination 1 Press the Quick No. Search key (or [No.]) in the basic send screen. 2 In the number entry screen, use the numeric keys to enter the speed dial number. 3 If you entered speed dial number between 1 and 3 digits long, press the Enter key (or [OK]). Place original. Destination Detail Address Book 1234567890 A OFFICE 1/10 B OFFICE Enter One Touch key number using # keys. C OFFICE Folder Path Entry (0001 - 1000) On Hook Direct 0011 FAX No. Entry 00 0001 AAA BBB Cancel 0006 FFF 0007 GGG Destination E-mail Addr Entry HHH Quick Setup Status OPERATION GUIDE i-FAX Addr Entry OK 0008 0009 III Original/Sending Data Format 0010 1/100 JJJ Color/ Image Quality The specified destination appears in the destination list. WSD Scan Advanced Setup 08/08/2009 10:10 NOTE: If you enter a 4-digit speed dial number, the operation in step 3 can be omitted. The basic send screen appears and the specified destination appears in the destinations list. 3-3 3 Basic Operation Touch Panel Display Display for Originals and Paper The touch panel displays the selected paper source and output tray. Press Start key to start printing. Copies 1 Press [Cancel] to change settings. Original position Copy Image Output tray Paper source Size/orientation of original and paper Auto Original Zoom Paper : Letter : 100% : Letter Cancel Quick Setup Status 3-4 Paper Selection 2 sided >>2 sided Duplex Org./Paper/ Finishing 100% Normal 0 Zoom Shortcut 1 Shortcut 2 Shortcut 3 Shortcut 4 Density Shortcut 5 2 in 1 Combine Image Quality Off Staple/Punch Layout/Edit Shortcut 6 Advanced Setup 08/08/2009 10:10 OPERATION GUIDE Basic Operation Original Preview You can display a preview image of the scanned document on the panel. NOTE: To view a preview of an image stored in a Custom Box, refer to Previewing Documents/Checking Document Details on page 3-39. The procedure for previewing scanned originals is explained below. 3 The procedure described here is for copying a single-page original. Ready to copy. Copies 1 Copy Image 1 Press the Copy key and place the original on the platen. 2 Press [Preview]. 3 The machine starts scanning the original. When scanning is completed, the preview image appears on the panel. 4 To change the quality or the layout, press [Cancel] or the Stop key. Change the settings and press [Preview] again to see a preview image with the new settings. Shortcut 1 Shortcut 2 Place original. Shortcut 3 Auto Original Zoom Paper : --: 100% --Preview Quick Setup Paper Selection 2-sided >>2-sided Duplex Org./Paper/ Finishing 100% Normal 0 Shortcut 4 Density Zoom Shortcut 5 2 in 1 Off Combine Image Quality Staple/Punch Layout/Edit Shortcut 6 Advanced Setup 08/08/2009 Status Press Start key to start printing. 10:10 Copies 1 Press [Cancel] to change settings. Shortcut 1 Copy Image Shortcut 2 Shortcut 3 Auto Original Zoom Paper : Letter : 100% Letter Cancel Quick Setup Paper Selection 2-sided >>2-sided Duplex Org./Paper/ Finishing Status 100% Normal 0 Zoom NOTE: If you scan a multi-page original, only the first Shortcut 4 page is previewed. Density Shortcut 5 2 in 1 Combine Image Quality Off Staple/Punch Layout/Edit Shortcut 6 Advanced Setup 08/08/2009 10:10 5 OPERATION GUIDE If there is no problem with the preview image, press the Start key. Copying begins. 3-5 Basic Operation Copying Follow the steps as below for basic copying. 1 Press the Copy key when the Copy key/indicator is off. NOTE: If the touch panel is turned off, press the Energy Saver key or the Power key and wait for the machine to warm up. 2 Place the originals on the platen or in the optional document processor. NOTE: For loading instructions, refer to Loading Originals on page 2-30. Ready to copy. 3 Copies Shortcut 1 Copy Image Shortcut 2 To change the paper size, press, [Org./Paper/ Finishing], [Paper Selection] and select the desired paper source. Place original. Shortcut 3 Auto Original Zoom Paper : --: 100% : --Preview Quick Setup Status 3-6 Paper Selection 2-sided >>2-sided Duplex Org./Paper/ Finishing 00% Normal 0 Zoom Check that [Auto] is selected of Paper Selection on the touch panel. Paper that matches the size of the original will be selected automatically. Shortcut 4 Density Shortcut 5 2 in 1 Combine Image Quality Off Staple/Punch Layout/Edit NOTE: Select paper size manually, if necessary, Shortcut 6 instead of using automatic paper selection. Advanced Setup 08/08/2009 10:10 4 Use the numeric keys to enter the copy quantity. Specify the desired number up to 999. 5 Press the Start key to start copying. 6 Remove the finished copies from the top tray. OPERATION GUIDE Basic Operation Adjusting Density Use this procedure to adjust the density when copying. Density Adjustment Option Description Manual Adjust density using 7 or 13 levels. Auto Optimum density is selected according to the density of the original. 3 NOTE: You may choose Auto mode as the default setting (refer to Density on page 8-18). The procedure for adjusting the density of copies is explained below. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Set the original on the platen and press [Image Quality] -> [Density]. 4 Adjust density manually pressing [-3] (Lighter) to [+3] (Darker). You can change the density level [-3] (Lighter) to [+3] (Darker) in half-steps. Density Auto To change density adjustment from Manual to Auto, press [Auto]. Place original. Lighter -3 Original Zoom Paper : --: 100% : --- Darker Normal -2 -2.5 -1 -1.5 0 -0.5 +2 +1 +0.5 +1.5 +3 5 Press [OK]. 6 Press the Start key. Copying begins. +2.5 Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 3-7 Basic Operation Selecting Image Quality Select image quality suited to the type of original. The table below shows the quality options. Image Quality Option Description Text+Photo For originals with both text and photographs. Text For originals primarily consisting of text. Photo For photos taken with a camera. Printed Document For documents printed from this machine. The procedure for selecting the quality of copies is explained below. Ready to copy. Copies 1 Original Image 1 Press the Copy key. 2 Place the originals on the platen. 3 Set the original on the platen and press [Image Quality] -> [Original Image]. 4 Select the image quality. 5 Press [OK]. 6 Press the Start key. Copying begins. Select original image type for best results. [Printed Document]: Suitable for documents printed from this machine. Place original. Text+Photo Original Zoom Paper Preview Add Shortcut Status 3-8 Text Photo : --: 100% : --Printed Document Cancel OK 08/08/2009 10:10 OPERATION GUIDE Basic Operation Zoom Copying Adjust the magnification to reduce or enlarge the original image. The following zoom options are available. Auto Zoom Ledger: 129 % Automatically reduces or enlarges the original image suitably to the selected paper size. Letter-R A3: 141 % Statement-R: 64 % A4 A5: 70 % Manual Zoom Manually reduces or enlarges the original image in 1% increments between 25% and 400%. 25 % 400 % Preset Zoom Reduces or enlarges at preset magnifications. The following magnifications are available. Model Zoom Level (Original Copy) Inch Models 100%, Auto, 400% (Max.), 200% (STMT >> Ledger), 154%(STMT >> Legal), 129% (Letter >> Ledger), 121% (Legal >> Ledger), 78% (Legal >> Letter), 77% (Ledger >> Legal), 64% (Ledger >> Letter), 50% (Ledger >> STMT), 25% (Min.) Metric Models 100%, Auto, 400% (Max.), 200% (A5 >> A3), 141% (A4 >> A3, A5 >> A4), 127% (Folio >> A3), 106% (11×15" >> A3), 90% (Folio >> A4), 75% (11×15" >> A4), 70% (A3 >> A4, A4 >> A5), 50%, 25% (Min.) Metric Models (Asia Pacific) 100%, Auto, 400% (Max.), 200% (A5 >> A3), 141% (A4 >> A3, B5 >> B4), 122% (A4 >> B4, A5 >> B5), 115% (B4 >> A3, B5 >> A4), 86% (A3 >> B4, A4 >> B5), 81%(B4 >> A4, B5 >> A5), 70% (A3 >> A4, B4 >> B5), 50%, 25% (Min.) OPERATION GUIDE 3-9 3 Basic Operation XY Zoom Select vertical and horizontal magnifications individually. Reduce or enlarge original images in 1% increments between 25% and 400%. Y X The procedure for using zoom copying is explained below. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Set the original on the platen and press [Layout/ Edit] -> [Zoom]. 4 Press [Standard Zoom] to use Auto Zoom. Press [+] or [–] to change the displayed magnification as desired. You can also enter the magnification directly using the numeric keys by pressing [# Keys]. Zoom (25 - 400) Standard Zoom Place original. Original Zoom Paper XY Zoom : --: 400% : --Preview 400 400% Max. % 78% 200% STMT >>Ledger 154% Legal >>Letter # Keys 77% Ledger STMT >>Legal 100% 64% Ledger 129% Letter >>Ledger Auto 50% 121% Legal >>Ledger Add Shortcut >>Legal When using Preset Zoom, select the key of desired magnification. >>Letter Ledger >>STMT 25% Min. Cancel When using XY Zoom, press [XY Zoom]. OK Status 08/08/2009 10:10 Press [+] or [–] to change the displayed magnifications of X (horizontal) and Y (vertical). You can also enter the magnification directly using the numeric keys by pressing [# Keys]. Press [Original Orientation] to select orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. Copies Ready to copy. Zoom Standard Z m Place original. X (25 - 400) 100 % XY Zoom # Keys Y Original Zoom Paper Preview Add Shortcut Status 3-10 (25 - 400) 100 : --: 100% : --# Keys Cancel % Top Edge Top Original Orientation OK 08/08/2009 10:10 5 Press [OK]. 6 Press the Start key. Copying begins. OPERATION GUIDE Basic Operation Duplex Copying Produce two-sided copies. The following duplex options are available. You can also create single-sided copies from two-sided originals or originals with facing pages such as books. The following modes are available. One-sided to Two-sided Produces two-sided copies from one-sided originals. In case of an odd number of originals, the back side of the last copy will be blank. 5 4 5 3 3 4 1 2 2 1 Original Copy A ghi def ghi abc A Original Left/Right to Binding Left/Right: Images on the second sides are not rotated. abc def abc The following binding options are available. B ghi def Original B Original Left/Right to Binding Top: Images on the second sides are rotated 180°. Copies can be bound on the top edge, facing the same orientation when turning the pages. Copy Two-sided to One-sided 1 Copies each side of a two-sided original onto two individual sheets. The optional document processor is required. 2 1 2 Original Copy The following binding options are available. • • Binding Left/Right: Images on the second sides are not rotated. Binding Top: Images on the second sides are rotated 180°. Two-sided to Two-sided 5 5 3 3 Produces two-sided copies from two-sided originals. The optional document processor is required. 4 4 1 1 2 2 Original OPERATION GUIDE Copy NOTE: The paper sizes supported in Two-sided to Two-sided are Ledger, Legal, Letter, Letter-R, Executive, Statement-R, Oficio II, 8.5×13.5", A3, B4, A4, A4-R, B5, B5-R, A5-R and Folio. 3-11 3 Basic Operation Book to One-sided 1 2 Produces a 1-sided copy of a 2-sided or open book original. 2 1 The following binding options are available. Original • Copy • Binding Left: Originals with facing pages are copied from left to right. Binding Right: Originals with facing pages are copied from right to left. NOTE: The following sizes of originals and paper are supported in Two-sided to One-sided and Book to Onesided. Original: Ledger, Letter-R, A3, B4, A4-R, B5-R, A5-R and 8K. Paper: Letter, A4, B5 and 16K. You may change paper size and reduce or enlarge copy to match that size. Book to Two-sided Facing pages -> Facing pages Facing pages -> Two-sided 4 2 1 4 3 3 1 1 2 2 1 0 3 4 2 3 NOTE: The following sizes of originals and paper are supported in Book to Two-sided mode. Original: Ledger, Letter-R, A3, B4, A4-R, B5-R, A5-R and 8K. Paper: Letter, A4 and B5. 2 1 3 4 3 1 0 2 Original Produces two-sided copies from an open book original with facing pages. Copy The procedure for using two-sided/duplex copying is explained below. Copies Ready to copy. Duplex 1-sided >>1-sided Place original. 1-sided >>2-sided 2-sided >>1-sided 2-sided >>2-sided Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 3-12 Book >>1-sided Book >>2-sided Top Edge Top Binding Top Cancel Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Duplex]. 4 Select the desired Duplex option. 5 If you choose [1-sided>>2-sided] or [2-sided>>2-sided], select the binding edge of the finished copies of Finishing. If you choose [Book>>2-sided], press [Book>>2sided] or [Book>> Book] of Finishing to select the setting for duplex. Finishing Binding Left/Right 1 Original Orientation OK 08/08/2009 10:10 OPERATION GUIDE Basic Operation Copies Ready to copy. 6 If you choose [2-sided>>1-sided], [2-sided>>2-sided], [Book>>1-sided] or [Book>>2-sided], select the binding edge of the originals of Original. 7 Press [Original Orientation] to select orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 8 Press [OK]. 9 Press the Start key. Duplex Original 1-sided >>1-sided Place original. 1-sided >>2-sided Binding Left/Right 2-sided >>1-sided Binding Top 2-sided >>2-sided Original Zoom Paper : --: 100% : --Preview Top Edge Top Book >>1-sided Original Orientation Book >>2-sided Add Shortcut Cancel OK 08/08/2009 Status 10:10 Once an original placed on the platen is scanned, replace it with the next one. Then, press the Start key. After scanning all originals, press [Finish Scan] to start copying. Collate/Offset Copying The machine can collate and offset at the same time as it copies. You can use the Collate/Offset copy function for tasks such as those shown below. Collate Scan multiple originals and deliver complete sets of copies as required according to page number. 3 2 1 3 3 2 2 1 1 3 2 1 Original Copy Offset Without Document Finisher If the optional document finisher is not installed, when you use offsetting, printed copies are produced after rotating each set (or page) by 90º. 3 2 1 3 1 1 2 3 2 3 2 1 Original OPERATION GUIDE NOTE: You need to load the same sized paper with different orientation in the paper source other than the selected paper source. The paper sizes supported in Offset are A4, B5, Letter and 16K. Copy (each set) 3-13 3 Basic Operation With Document Finisher 3 2 1 3 2 1 3 2 1 Original When you use offsetting, printed copies are segregated after each set of copies (or after each page). 3 2 1 NOTE: The optional document finisher or 3,000 sheet document finisher is required. Copy (each set) The procedure for using collate/offset copying is explained below. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Collate/ Offset]. 4 To use collate copying, press [On] of Collate. To use offset copying, press [Each Set] of Offset. Collate/Offset Collate Place original. Original Zoom Paper : --: 100% : --- Off On Off Each Set Press [OK]. Offset Preview Add Shortcut Cancel OK Status 08/08/2009 Ready to copy. 10:10 If [Off] is selected for Collate, press [Off] or [Each Page] of Offset. Copies Collate/Offset Collate Place original. Original Zoom Paper : --: 100% : --- Off On Off Each Page 5 Press [OK]. 6 Press the Start key. Copying begins. Offset Preview Add Shortcut Status 3-14 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Basic Operation Reserve Next This function allows you to reserve the next job during printing. Using this function, the original will be scanned while the machine is printing. When the current print job ends, the reserved copy job is printed. The procedure differs depending on the Reserve Next Priority (refer to page 8-27). If Reserve Next Priority is set to [On] 3 The Copy function default screen appears on the touch panel during printing. Ready to copy. Copies 1 Place the originals onto the machine for reserving copy, and configure the copy settings. 2 Press the Start key. Shortcut 1 Copy Image Shortcut 2 Place original. Shortcut 3 Auto Original Zoom Paper 100% Paper Selection : --: 100% : --- 2-sided >>2-sided Preview Duplex Quick Setup Org./Paper/ Finishing Normal 0 Zoom Shortcut 4 Density Shortcut 5 2 in 1 Combine Image Quality Off Shortcut 6 Staple/Punch Layout/Edit Advanced Setup 08/08/2009 Status 10:10 The machine starts scanning the originals. When the current print job ends, the reserved copy job is printed. If Reserve Next Priority is set to [Off] The Copying screen appears on the touch panel during printing. Job No.: 000021 1 Copies Copying... Job Name: Scanner Setting Doc10102008101031 Press [Reserve Next]. The default screen for copying appears. User Name: ----Printer Setting Scanned Pages Copies 2 2/ 24 Letter Letter 100% 2-sided 2-sided Collate Plain Top Edge Top Top Tray Cancel Status Reserve Next 10:10 2 Place the originals onto the machine for reserving copy, and configure the copy settings. 3 Press the Start key. The machine starts scanning the originals. When the current print job ends, the reserved copy job is printed. OPERATION GUIDE 3-15 Basic Operation Interrupt Copy This function allows you to pause the current jobs in progress when you need to make copies immediately. When interruption copy ends, the machine resumes the paused print jobs. NOTE: You can change the delay until interrupt copying is cancelled. Change the delay as required. For more information, refer to Interrupt Clear Timer on page 8-50. Ready for interrupt copy. Copies 1 1 Ready for interrupt copy. is displayed. Shortcut 1 Copy Image Press the Interrupt key. Shortcut 2 The current print job is temporarily interrupted. Place or ginal. Shortcut 3 Auto Original Zoom Paper : --: 100% : --Preview Quick Setup Status 3-16 Paper Selection 2-sided >>2-sided Duplex Org./Paper/ Finishing 100% Normal 0 Zoom Shortcut 4 Density Shortcut 5 2 in 1 Combine Image Quality Off Staple/Punch Layout/Edit Shortcut 6 Advanced Setup 08/08/2009 10:10 2 Place the originals onto the machine for interrupt copy, and configure the copy settings. 3 Press the Start key to start interrupt copying. 4 When interrupt copying ends, press the Interrupt key. The machine resumes the paused print jobs. OPERATION GUIDE Basic Operation Staple Use this feature to staple your finished copies. NOTE: Stapling requires the optional built-in finisher, document finisher or 3,000 sheet document finisher. Note also that saddle stitching (center stapling) requires the folding unit. 3 The following stapling options and orientations are available. Original Orientation: Top Edge (Back Edge) Original Orientation: Top Edge (Back Edge) Original Orientation: Original Orientation: Left Top Edge (Left top Left Top Edge (Left top corner) corner) 3,000 Sheet Document Finisher Cassette Paper Load Direction 3,000 Sheet Document Finisher Cassette Paper Load Direction Document Finisher Cassette Paper Load Direction Document Finisher Cassette Paper Load Direction OPERATION GUIDE 3-17 Basic Operation Original Orientation: Top Edge (Back Edge) Original Orientation: Top Edge (Back Edge) Original Orientation: Original Orientation: Left Top Edge (Left top Left Top Edge (Left top corner) corner) Built-in Finisher Cassette Paper Load Direction Built-in Finisher Cassette Paper Load Direction Use the procedure below to produce stapled copies. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Staple/ Punch]. 4 Select the staple position. Staple/Punch Top Left 2 staples Top Top Right 2 staples Right 2 staples Left Bind and Fold Punch 2 holes Left 3 holes Left Off 2 holes Top 3 holes Top 2 holes Right 3 holes Right Staple Off Place original. Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 3-18 Cancel NOTE: To use saddle stitching, press [Bind and Fold]. When placing originals, be sure to place the cover page at the bottom. For more information on saddle stitching, refer to Booklet from Sheets on page 4-19. Top Edge Top Original Orientation 5 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 6 Press [OK]. 7 Press the Start key. Copying begins. OK 08/08/2009 10:10 OPERATION GUIDE Basic Operation Punch Punch holes in sets of finished copies in preparation for binding. NOTE: Requires the optional 3,000 sheet document finisher and punching unit. 3 The orientations of the original and corresponding punch positions are as follows. Original Copy Orientation of Original Platen Document processor NOTE: The inch model provides two-hole and three-hole punching. The metric model provides two-hole and four-hole punching. Follow the steps as below for punching. OPERATION GUIDE 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing]and then press [Staple/Punch]. 3-19 Basic Operation Copies Ready to copy. Staple/Punch Top Left 2 staples Top Top Right 2 staples Right 2 staples Left Bind and Fold Punch 2 holes Left 3 holes Left Off 2 holes Top 3 holes Top 2 holes Right 3 holes Right Staple Off Place original. Original Zoom Paper : --: 100% : --Preview Add Shortcut Status Cancel 4 Select the type of hole punching. 5 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 6 Press [OK]. 7 Press the Start key. Top Edge Top Original Orientation OK 08/08/2009 10:10 If the original is placed on the platen. Place the next original and press the Start key. Copying begins. If all original pages have been scanned, press [Finish Scan]. Copying begins. 3-20 OPERATION GUIDE Basic Operation Printing - Printing from Applications Follow the steps below to print documents from applications. NOTE: To print the document from applications, install the printer driver on your computer from the supplied CD-ROM (Product Library). 3 1 Create a document using an application. 2 Click File and select Print in the application. The Print dialog box appears. 3 Click the button next to the Name field and select this machine from the list. 4 Enter the desired print quantity in the Number of copies box. Enter any number up to 999. When there is more than one document, select Collate to print out one by one in the sequence of the page numbers. 5 OPERATION GUIDE Click Properties button. The Properties dialog box appears. 3-21 Basic Operation 6 Select the Basic tab and click Page Size button to select the paper size. To print on the special paper such as thick paper or transparency, click the Media Type menu and select the media type. 7 Click Source and select the paper source. NOTE: If you choose Auto Select, paper is supplied automatically from the paper source loaded with paper of optimum size and type. To print on special paper such as envelope or thick paper, place it on the multi purpose tray and select MP Tray. 8 Select paper orientation, either Portrait or Landscape, to match the orientation of the document. Selecting Rotate 180° will print the document rotated 180°. 9 Click OK button to return to the Print dialog box. 10 Click OK button to start printing. 3-22 OPERATION GUIDE Basic Operation Sending This machine can send a scanned image as an attachment to an E-mail message or to a PC linked to the network. In order to do this, it is necessary to register the sender and destination (recipient) address on the network. A network environment which enables the machine to connect to a mail server is required. It is recommended that a Local Area Network (LAN) be used to assist with transmission speed and security issues. At the same time as you send a scanned image, you can also print the image or send it to the Document Box. To use the Scanning Function perform the following steps: • Program the settings, including the E-mail setting on the machine. • Use Embedded Web Server (the internal HTML web page) to register the IP address, the host name of the SMTP server, and the recipient. • Register the destination in the Address Book or One Touch keys. • When the PC Folder (SMB/FTP) is selected, it is necessary to share the destination folder. For setting-up the PC Folder, contact your administrator. • Creating/Registering a Document Box (when a Document Box is selected as the destination) • Detailed transmission settings (to select a Document Box as the destination or to print and send the image at the same time) Follow the steps below for basic sending. The following four options are available. • Send as E-mail: Sends a scanned original image as an E-mail attachment...page 3-24 • Send to Folder (SMB): Stores a scanned original image in a shared folder of any PC...page 3-25 • Send to Folder (FTP): Stores a scanned original image in a folder of an FTP server...page 3-25 • Send to Document Box: Sends a document stored in a document box on this machine...page 6-6 • Image Data Scanning with TWAIN / WIA: Loads the document data stored in a Custom Box to a PC...Refer to the TWAIN/WIA Driver Operation Guide NOTE: Different sending options can be specified in combination. Refer to Sending to Different Types of Destinations (Multi Sending) on page 3-32. OPERATION GUIDE 3-23 3 Basic Operation Send as E-mail Sends a scanned original image as an E-mail attachment. NOTE: • You must have a network environment in which this machine can connect to a mail server. It is recommended that the machine be used in an environment in which it can connect to the mail server at any time over a LAN. • Access the Embedded Web Server beforehand and specify the settings required for sending e-mail. For details, see Embedded Web Server (Settings for E-mail) on page 2-16. 1 Press the Send key. Displays the screen for sending. NOTE: Depending on the settings, the address book screen may appear. In this event, press [Cancel] to display the screen for sending. Ready to send. 2 Destination Place original. Press [E-mail Addr Entry] and then [E-mail Address]. E-mail Address Entry E-mail Address NOTE: Destination can be specified using the Address Book or the One Touch Keys. Refer to Specifying Destination on page 3-30. Add a new e-mail destination. Press [E-mail Address], then enter the address using the keyboard screen. Add to Addr Book Status Next Dest. Cancel OK 08/08/2009 10:10 3 Enter destination E-mail address and press [OK]. 4 Press [Next Dest.] and repeat steps 3 to specify the destination. Up to 100 E-mail addresses can be specified. NOTE: When [Add to Addr Book] is displayed, the destinations are registered in the Address Book. 5 3-24 Press [OK]. The destinations are registered in the destination list. OPERATION GUIDE Basic Operation Ready to send. 6 Destination Check the destination list. Place original. Destination Detail ABCD TUVW 10.200.188.120 Group1 Group1 On Hook Direct 1/1 E-mail Addr Entry Select a destination and press [Delete] to remove the destination from the list. Folder Path Entry Detail/Edit Chain Auto Select a destination and press [Detail/Edit] to check and edit it. Address Book To: [email protected] Delete Recall FAX No. Entry 0001 AAA 0002 BBB 0006 FFF 0007 GGG Destination 0003 CCC 0004 0008 HHH Quick Setup Status 0005 No. i-FAX Addr Entry EEE DDD 0009 III Original/Sending Data Format 0010 1/100 JJJ Color/ Image Quality WSD Scan Advanced Setup 08/08/2009 10:10 NOTE: When selecting [On] for Entry Check for New Destination (page 8-31), the confirmation screen appears. Enter the same destination again and press [OK]. When selecting [On] for Destination Check before Send (page 8-30), the confirmation screen appears after pressing the Start key. For details, refer to Confirmation Screen of Destinations on page 3-29. Send to Folder (SMB)/Send to Folder (FTP) Stores a scanned original image file in the specified shared folder of any PC. Stores a scanned original image in a folder of an FTP server. NOTE: • Refer to Help of your operating system for details on how to share a folder. • Be sure that SMB Protocol or FTP in the Embedded Web Server is On. For details, refer to the Embedded Web Server Operation Guide. 1 Press the Send key. Displays the screen for sending. NOTE: Depending on the settings, the address book screen may appear. In this event, press [Cancel] to display the screen for sending. 2 Press [Folder Path Entry] and then [SMB] or [FTP]. NOTE: Destination can be specified using the Address Book or the One Touch Keys. For details, refer to Specifying Destination on page 3-30. OPERATION GUIDE 3-25 3 Basic Operation Ready to send. Destination 3 Enter host name, path, login user name and login password. Press the key of each item to first display the entry screen. 4 Enter the destination data and press [OK]. Place original. Folder Path Entry SMB Host Name Path FTP Login User Name Login Password Specify th computer. older on the destinat on Connection Test Add to Addr Book Next Dest. Cancel OK 08/08/2009 Status 10:10 Use the keyboard to enter. L mit: 128 characters In ut: 0 characters Backspace ! @ Q # W A E S Z Upper-case $ % R D X T F C Lower-case ^ Y G V & U H B * ( I J N O K M No./Symbol ) _ P L < { : > + } | " ? Space Cancel OK 08/08/2009 Status 10:10 Data to be entered are as follows. NOTE: You will be unable to send the data if you forget your login user name or login password. Contact your administrator and check your login user name or login password. For send to folder (SMB) Item Max. characters Host Name* Host name or IP address of the PC to receive the data. Up to 64 characters Path Path to the receiving folder such as follows. For example, \User\ScanData. Up to 128 characters Login User Name User name to access the PC For example, abcdnet\james.smith Up to 64 characters Login Password Password to access the PC Up to 64 characters * 3-26 Data to be entered To specify a port number different from the default (139), enter using the format “host name: port number” (e.g., SMBhostname:140). To enter the IPv6 address, enclose the address in brackets [ ]. (e.g., [3ae3:9a0:cd05:b1d2:28a:1fc0:a1:10ae]:140) OPERATION GUIDE Basic Operation For send to folder (FTP) Item Data to be entered Max. characters Host Name* Host name or IP address of FTP server Up to 64 characters Path Path to the receiving folder. For example, \User\ScanData. Otherwise the data will be saved in the home directory. Up to 128 characters Login User Name FTP server login user name Up to 64 characters Login Password FTP server login password Up to 64 characters * 3 To specify a port number different from the default (21), enter using the format “host name: port number” (e.g., FTPhostname:140). To enter the IPv6 address, enclose the address in brackets [ ]. (e.g., [3ae3:9a0:cd05:b1d2:28a:1fc0:a1:10ae]:140) Ready to send. 5 Destination Place original. Upon completion of all entries, press [Connection Test] to check the connection. Folder Path Entry SMB FTP Host Name NOTE: Connected. appears when connection to the destination is correctly established. If Cannot connect. appears, review the entry. Path Login User Name Login Password Specify the folder on the destinat on computer. Add to Addr Book Status Next Dest. To specify another destination, go to the step 6. To specify only one destination, go to step 7. Connection Test Cancel OK 08/08/2009 10:10 6 Press [Next Dest.] and repeat steps 3 to 5 to specify the destination. You can specify a combined total of up to 10 FTP and SMB destination folders. NOTE: When [Add to Addr Book] is displayed, the entry is registered in the Address Book. 7 OPERATION GUIDE Press [OK] to register the entry in the destination list. 3-27 Basic Operation Ready to send. 8 Destination Check the destination list. Place original. Destination Detail ABCD TUVW 10.200.188.120 Group1 Group1 On Hook Direct Auto 1/1 E-mail Addr Entry Delete Recall FAX No. Entry 0001 AAA 0002 BBB 0006 FFF Destination Status 0003 CCC 0007 GGG 0004 Quick Setup 0005 No. i-FAX Addr Entry EEE DDD 0008 HHH Select a destination and press [Detail/Edit] to check and edit it. Edit it, if necessary, referring to steps 3 to 5. Folder Path Entry Detail/Edit Chain Address Book To: [email protected] 0009 III Original/Sending Data Format 0010 1/100 JJJ Color/ Image Quality Select a destination and press [Delete] to remove the destination from the list. WSD Scan Advanced Setup 08/08/2009 10:10 NOTE: When On is selected in FTP Encrypted TX (page 5-31), keys appear for selecting the encryption method for the FTP transmission destination. Select Auto, DES, 3DES or AES as the encryption method. When selecting [On] for Entry Check for New Destination (page 8-31), the confirmation screen appears. Enter the same host name and path again, and press [OK]. When selecting [On] for Destination Check before Send (page 8-30), the confirmation screen appears after pressing the Start key. For details, refer to Confirmation Screen of Destinations on page 3-29. 3-28 OPERATION GUIDE Basic Operation Confirmation Screen of Destinations When selecting [On] for Destination Check before Send (page 8-30), the confirmation screen of destinations appears after pressing the Start key. Follow the steps below to confirm the destinations. Ready to send. 1 Destination Press [ ] or [ ] to confirm every destination. Place original. Destination Detail ABCD [email protected] To: TUVW 10.200.188.120 Auto Group1 Group1 On Hook Direct 1/1 E-mail Addr Entry To delete the destination, select the destination you want to delete and press [Delete]. Press [Yes] in the confirmation screen. The destination is deleted. Folder Path Entry Detail/Edit Chain Press [Detail] to display the detailed information on the selected destination. Address Book Delete Recall FAX No. Entry 0001 AAA 0002 BBB 0006 FFF Destination 0003 CCC 0007 GGG 0004 0008 HHH Quick Setup Status 0005 No. 0010 1/100 i-FAX Addr Entry EEE DDD 0009 III Original/Sending Data Format JJJ Color/ Image Quality To add the destination, press [Cancel] and then return to the destination screen. WSD Scan Advanced Setup 08/08/2009 10:10 2 Press [Check]. NOTE: Be sure to confirm every destination by displaying them on the touch panel. You cannot press [Check] unless you have confirmed every destination. 3 OPERATION GUIDE Press the Start key to start sending. 3-29 3 Basic Operation Specifying Destination When specifying destination, choose from the Address Book or use the One Touch Keys. NOTE: You can set the machine up so that the address book screen appears when you press the Send key. For details, refer to Setting the Default Send Screen on page 8-31. Choosing from the Address Book Select a destination registered in the Address Book. Ready to send. 1 In the basic screen for sending, press [Address Book]. 2 Detail Press the checkbox to select the desired destination from the list. You may choose multiple destinations. The selected destinations are indicated by a checkmark in the check box. To use an address book on the LDAP server, select [Ext Address Book] from the Addr Book pull-down menu. OK You can change the order in which the destinations are listed by selecting [Name] or [No.] from the Sort pull-down menu. Destination Place original. Destination Detail ABCD [email protected] To: TUVW 10.200.188.120 Auto Address Book 1/1 Group1 Group1 On Hook Direct Folder Path Entry Detail/Edit Chain E-mail Addr Entry Delete Recall FAX No. Entry 0001 0002 AAA BBB 0006 0003 CCC 0007 FFF 0004 GGG 0008 0009 i-FAX Addr Entry 0010 III Quick Setup No. EEE DDD HHH Destination 0005 1/100 JJJ Original/Sending Data Format Color/ Image Quality WSD Scan Advanced Setup 08/08/2009 Status 10:10 Address Book Addr Book No. Sort Address Book Type Name Name Detail 001 ABCD [email protected] 002 TUVW [email protected] 003 Group1 004 Group2 Search(Name) Search(No.) 005 ABC DEF E-mail 1/2 Register/Edit Address Book Group3 GHI JKL MNO Folder PQRS TUV FAX WXYZ 09 Group i-FAX Cancel Status 08/08/2009 10:10 NOTE: To cancel the selection, press the check box and remove the checkmark. For details on the external address book, refer to Embedded Web Server Operation Guide. 3 Press [OK] to register the selected destination in the destination list. NOTE: To delete a destination in the list, select the destination and press [Delete]. 3-30 OPERATION GUIDE Basic Operation Destination Search Destinations registered in the Address Book can be searched. Advanced search by type or by initial letter is also available. Address Book Addr Book Dest. (1) (2) No. Name Name Deta l 0001 ABCD [email protected] 0002 TUVW [email protected] 0003 Group1 0004 Group2 Search(No.) ABC (4) DEF 1/2 Register/Edit Address Book Detail Group3 GHI E-mail JKL MNO Folder PQRS TUV FAX WXYZ 09 Group i-FAX Cancel OK 08/08/2009 Status Keys used 3 Search(Name) 0005 (3) Sort Address Book Type Search type 10:10 Subjects searched 1 Search by name Search by registered name. 2 Search by address number Search by registered address number. 3 Advanced search by initial letter Advanced search by initial letter of registered name. 4 Advanced search by destination Advanced search by type of registered destination (E-mail, Folder (SMB/FTP), FAX, i-FAX or Group). (FAX: Only when the optional fax kit is installed.i-FAX: Only when the optional internet fax kit is installed). You can set this function up so that destination types are selected when the address book is displayed. For more information, refer to Narrow Down Settings on page 8-57. The procedures for using the different search modes are explained below. Search by name Press [Search(Name)] and enter the required name. Search by address number Press [Search(No.)] and enter the address number you wish to search. Advanced search by initial letter Press the key for the required initial letter. Advanced search by destination Press any of [E-mail], [Folder], [FAX], [i-FAX] or [Group]. The destinations registered by that type are displayed. OPERATION GUIDE 3-31 Basic Operation Choosing by One Touch Key Ready to send. Select the destination using the One Touch Keys. Destination Place original. Destination Detail ABCD [email protected] To: TUVW 10.200.188.120 Auto Group1 Group1 On Hook Direct 1/1 E-mail Addr Entry Folder Path Entry Detail/Edit Chain Address Book Delete Recall FAX No. Entry 0001 0002 AAA BBB 0006 0003 CCC 0007 FFF GGG 0009 III Quick Setup 0005 No. 0010 1/100 i-FAX Addr Entry EEE DDD 0008 HHH Destination 0004 JJJ Original/Sending Data Format Color/ Image Quality WSD Scan Advanced Setup 08/08/2009 Status 10:10 In the basic screen for sending, press the One Touch Keys where the destination is registered. NOTE: If the One Touch Keys for the desired destination is hidden on the touch panel, press [ ] or [ ] to scroll and view next or previous One Touch Keys. This procedure assumes that One Touch Keys have already been registered. Refer to Adding a Destination on One Touch Key on page 8-55 for more information on adding One Touch keys. Choosing by Speed Dial Ready to send. Access the destination by specifying the 4-digit (0001 to 1000) One Touch Key number (speed dial). Destination Place original. Destination Detail ABCD TUVW Auto 10.200.188.120 1/1 Group1 Group1 On Hook Address Book To: [email protected] Direct Folder Path Entry Detail/Edit Chain E-mail Addr Entry Delete Recall FAX No. Entry 0001 AAA 0002 BBB 0006 FFF Destination Status 0003 CCC 0007 GGG 0004 HHH Quick Setup No. 0010 1/100 i-FAX Addr Entry EEE DDD 0008 000 0009 III Original/Sending Data Format In the basic screen for sending, press the Quick No. Search key or [No.] and use the numeric keys to enter the One Touch key number in the numeric entry screen. JJJ Color/ Image Quality NOTE: if you entered the speed dial in 1 to 3-digit, WSD Scan press [OK]. Advanced Setup 08/08/2009 10:10 Sending to Different Types of Destinations (Multi Sending) You can specify destinations that combine e-mail addresses, folders (SMB or FTP) and fax numbers (optional). This is referred to as Multi Sending. This is useful for sending to different types of destination (e-mail addresses, folders, etc.) in a single operation. No. of broadcast items E-mail Folders (SMP, FTP) FAX i-FAX : Up to 100 : Total of 10 SMB and FTP : Up to 500 : Up to 100 Also, depending on the settings, you can send and print at the same time. Procedures are the same as used in specifying the destinations of respective types. Continue to enter E-mail address or folder path so that they appear in the destination list. Press the Start key to launch transmission to all destinations at one time. 3-32 OPERATION GUIDE Basic Operation Using Document Box What is Document Box? Document Box is an area in the hard disk in which you can save documents for later retrieval or sharing among multiple users. 3 Document Box contains four types of component boxes which provide the following functions. Custom Box...page 6-2 Custom Box is a component box which you can create within the Document Box and store data for later retrieval. You can create or delete a Custom Box, and manipulate data in various ways as described below: • Creating a box...page 6-2 • Storing Documents in a Custom Box...page 6-4 • Printing a Document in a Custom Box...page 6-5 • Sending a Document from a Custom Box...page 6-6 • Moving/ Copying /Joining Documents in a Custom Box...page 6-8 • Deleting Documents in a Custom Box...page 6-11 Job Box Job Box holds temporary or permanent print data for use with job options including Private Print, Stored Job, Quick Copy, Proof and Hold, Repeat copy and Form Overlay which will be discussed later. Four individual Job Boxes corresponding to these job options are already provided in the Document Box. These Job Boxes cannot be created or deleted by a user. NOTE: You can set up the machine so that temporary documents in job boxes are automatically deleted. For details, refer to Automatic Delete Setting for Temporary Documents on page 6-17. Private Print/Stored Job Box...page 6-12 In Private Printing, you can specify that a job is not printed until you release the job at the operation panel. When sending the job from the application software, specify a 4-digit access code in the printer driver. The job is released for printing by entering the access code on the operation panel, ensuring confidentiality of the print job. The data will be deleted upon completion of print job or after the main power switch is turned off. In Hold Job, access codes are not mandatory, but can be set on the printer driver if printing with PIN security is required. In this event, you need to enter the access code to print the stored jobs. Print data will be stored in the hard disk after printing. This will allow printing of the same print data repeatedly. Quick Copy/Proof and Hold Box...page 6-13 Quick Copy feature facilitates additional prints of a document already printed. Activating Quick Copy and printing a document using the printer driver allow the print data to be stored in the Quick Copy Job Box. OPERATION GUIDE 3-33 Basic Operation When additional copies are required, you can reprint the required number of copies from the operation panel. By default, up to 32 documents can be stored. When power is turned off, all stored jobs will be deleted. NOTE: When you attempt to store documents in excess of the above maximum, the oldest document data will be overwritten by the latest document data. The Proof and Hold feature produces only a single proof print of multiple-print job and holds printing of the remaining copies. Printing a multiple-print job in Proof and Hold using the printer driver allows only a single copy to be printed while maintaining the document data in the Job Box. To continue to print the remaining copies, use the operation panel. You can change the number of copies to print. Repeat Copy Box...page 6-15 Repeat Copy feature stores the copied original document data in the Job Box and allows you to print additional copies later. By default, up to 32 documents can be stored. When power is turned off, the original data will be deleted. NOTE: Repeat Copy function is not available when the optional Data Security Kit is installed. Form for Form Overlay Box...page 6-17 Image Overlay feature copies the original document overlaid with a form or image. This Job Box is used to store the forms or images for overlaying. Removable Memory Box A USB memory inserted into the USB memory slot (A1) of the machine is also recognizable as a Job Box. This allows printing of the PDF data stored in the USB memory. You can print PDF data directly from the USB memory without a PC. Image files scanned using this machine can also be saved to USB memory in the PDF, TIFF, JPEG, XPS or high compression PDF format (Scan to USB). Fax Box Fax Box stores the fax data received. For details, refer to the Operation Guide supplied with the fax kit. 3-34 OPERATION GUIDE Basic Operation Basic Operation for Document Box This section explains basic operations for document boxes, using examples where tasks are carried out with custom boxes. NOTE: In the following explanation, it is assumed that user login administration is enabled. For details on User Logon privileges, refer to User Privileges on page 3-40. 3 The basic procedure for using document boxes is explained below. 1 Press the Document Box key. The default document box screen appears. 2 Custom Box. No. 0001 Name Owner SALES Used Area Anonymous ---- Search(Name) In this example, press [Custom Box]. Search(No.) 1/1 Store File Custom Box Job Box Detail Removable Memory Press [Custom Box], [Job Box] or [Removable Memory] to select the type of document box you want to work with. Register/Edit Box The box list screen appears. You can use this screen for tasks such as registering and editing boxes. For more information on using the box list, refer to Custom Box List on page 3-36. Open FAX Box Status 08/08/2009 10:10 NOTE: For more information on registering boxes, refer to Creating a New Custom Box on page 6-2. You cannot access boxes if you forget your password. In this event, access the machine using administrator privileges and overwrite your box password. 3 Custom Box. No. Name Owner Used Area 0001 0001 Box 1 User 10% Search(Name) 0002 0002 Box 2 User 20% Search(No.) 0003 0003 Box 3 User 30% 1/1 Store File Custom Box Job Box Detail Removable Memory Status OPERATION GUIDE Select the box containing the document you want to work with and press [Open]. The document list screen appears. You can use this screen for tasks such as printing and sending documents. For more information on using the document list, refer to Document List on page 3-37. Register/Edit Box Open FAX Box 08/08/2009 10:10 NOTE: If a custom box is protected by a password, enter the correct password. 3-35 Basic Operation Custom Box List The box list shows the registered custom boxes. The custom boxes can be listed by box number or by box name. You can manipulate the list in a range of ways, as shown below. Listing the boxes by number in ascending/descending order. Listing the boxes by name in alphabetical order. Custom Box. No. Name Owner Used Area 0001 0001 Box 1 User 10% 0002 0002 Box 2 User 20% 0003 0003 Box 3 User 30% Search(Name) Search(No.) 1/1 Store File Custom Box Job Box Detail Removable Memory Opens the selected box. Open FAX Box Status 08/08/2009 Saves the document in the selected box. 3-36 Registers new boxes and checks, modifies or deletes box information. Reg ster/Edit Box 10:10 Displays the details for the selected box. OPERATION GUIDE Basic Operation Document List The document list is a list of the documents stored in the custom box. Documents can be listed either by name or as thumbnails. The list can be used as shown below. List Listing the documents by name in alphabetical order. Selecting more than one document at a time. Selecting documents by checking checkboxes. Listing the documents by time of update in ascending/descending order. Listing the documents by size in ascending/descending order. 3 Box: Date and Time Size 0 File Name 0404200710574501 10/10/2008 09:40 21 MB 0002 0404200710574511 10/10/2008 09:50 21 MB 0003 0404200710574521 10/10/2008 10:00 21 MB Search(Name) Highlighting a document to display its details with [Detail]. 1/1 Detail Previews the selected document. Preview Print Send Join Move/Copy Delete Store File Close 08/08/2009 Status 10:10 Thumbnail Selecting more than one document at a time. Switches between list display and thumbnail display. Box: ALES Search(Name) Highlighting a document to display its details with [Detail]. 0420075501 040420075502 Prints, sends, joins, moves, copies or deletes the selected documents. 1/1 Detail Selecting documents by checking checkboxes. eview Print Send Join Move/Copy Delete Saves the document in the open box. Store File Close Status 08/08/2009 10:10 NOTE: You can select multiple documents by pressing the respective document checkboxes. However, note that you cannot select multiple documents when you are sending documents. OPERATION GUIDE 3-37 Basic Operation Viewing/Editing Box Details You can check and modify box information. Use the procedure below. Document Box/Removable Memory - Register/Edit Box No Name 0001 SALES Owner 1 Press [Register/Edit Box] in the box list screen. 2 Highlight the box whose details you wish to check or edit and press [Detail/Edit]. Used Area Anonymous ---- Search(Name) NOTE: If a custom box is protected by a password, Search(No.) 1/1 Detail/Edit enter the correct password. Add Delete Close 08/08/2009 Status 10:10 3 Box: Box No.: Change To edit details, press [Change] of the detail you wish to edit. Edit the detail as desired and press [OK]. 0001 Box Name: Change SALES Box Password: Usage Restriction: 21 Check the box details. Change MB Change ******** Auto File Deletion: 30 day(s) Free Space: 30 GB Change Overwrite Setting: Delete after Printed: Change Off Cancel Status Change Permit Register 08/08/2009 10:10 4 If you have changed the details, press [Register] and then press [Yes] in the confirmation screen. If you did not change the details, press [No]. 5 3-38 Press [Close]. The display returns to the default Document Box screen. OPERATION GUIDE Basic Operation Previewing Documents/Checking Document Details You can use this function to preview the documents stored in a document box or display the document details for checking. Use the procedure below. 1 Select (highlight) a document to preview and then press [Preview] or [Detail]. 2 Preview the document or check the document details. The operations available in the preview screen are shown below. When you have zoomed in, you can use these keys to move the displayed area. Preview: 2007040410574501 No. Size : Resol. : Color : 1/6 In multiple-page documents, you can change pages by entering the desired page number. In multiple-page documents, you can use these buttons to change pages. Close 0 08/2009 Status Zoom out. 3 OPERATION GUIDE 10:10 Zoom in. When you have finished previewing documents or checking document details, press [Close]. 3-39 3 Basic Operation User Privileges When user login administration is enabled, accessibility to the Document Box components will vary depending on the given user privilege. Accessibilities vary depending on user privilege as follows: Access level Administrator User Creating a box Yes No Changing box owner Yes No Others Yes No Owner Yes Yes Changing box number Others Yes No Owner Yes No Renaming a box Others Yes No Owner Yes Yes Changing the password to a box Others No No Owner Yes Yes Overwriting the password to a box Others Yes No Owner Yes No Adjusting the box capacity Others Yes No Owner Yes No Changing the owner Others Yes No Owner Yes No Changing the permisson Others Yes No Owner Yes Yes Changing the period of using a box Others Yes No Owner Yes Yes Accessibility Operation Box information Deleting a box Restricting the Accessibility to a Box The accessibility to a Custom Box differs depending on the level of privileges as follows: Administrator: An administrator can gain access and manipulate all boxes. User: 3-40 A user can gain access and manipulate his/her own boxes and the shared boxes. OPERATION GUIDE Basic Operation Password Entry Requirement When user login administration is enabled, requirement of a password differs depending on the level of privileges as follows: Administrator: The administrator is not required to enter a password to gain access to any box. The user is required to enter a password to gain access to a box which is protected by a password. The user is not required to enter a password to gain access to his/her own boxes. User: Creating new Custom Boxes when user login administration is enabled If you create a new Custom Box when user login administration is enabled, the screen appears and you can change the owner and permission settings. Only administrators and machine administrators can create new Custom Boxes. Box: ** Box No.: Change 0001 Change Box Password: Change ********** Auto File Deletion: Usage Restriction: 21 SALES Change GB Permission: Change Private Change day(s) Overwrite Setting: Changing the owner: Change Permit Free Space: 30 Change DCBA9876 Box Name: 30 Owner: Delete after Printed: Change Off GB Cancel Status Register 08/08/2009 10:10 Press [Change] of Owner and select the new owner for the box from the displayed list. Then press [OK]. Changing the permission:Press [Change] of Permission and select either [Private] or [Shared]. Then press [OK]. NOTE: For information on specifying other settings, refer to Creating a New Custom Box on page 6-2. Working With User Privileges When User Login Administration is Enabled When user login administration is enabled, the owner of a box with user privileges set can change the following box information: the box name, the box password, the permission, the auto file deletion and the overwrite setting. Box: Box No.: Owner: 0001 DCBA9876 Box Name: Change Usage Restriction: Change Permission: 21 MB SALES Box Password: Auto File Delet on: Change 30 day(s) Free Space: 30 Change Private ******** GB Overwrite Setting: Delete after Printed: Change Off Cancel Status Change Permit Register 08/08/2009 10:10 NOTE: It is assumed that a custom Document Box has already been created and registered. For information on creating/registering Document Boxes, refer to Creating a New Custom Box on page 6-2. OPERATION GUIDE 3-41 3 Basic Operation Canceling Jobs Follow the steps below to cancel any print or send job being executed. Canceling Jobs You can also cancel jobs by pressing the Stop key. Printing jobs 1 Press the Stop key. Cancelling job screen appears. The current print job is temporarily interrupted. 2 Select the job you wish to cancel and press [Cancel]. And then press [Yes] in the confirmation screen. 1 Press the Stop key. Sending jobs Job Cancel appears. NOTE: Pressing the Stop key will not temporarily stop a job that you have already started sending. 2 Job No.: 000021 Job Name: Scanner Setting NOTE: Copies Copying... Doc10102008101031 If Reserve Next Priority (refer to page 8-27) is set to [Off] User Name: ----Printer Setting Scanned Pages Copies 2 2/ 24 Letter Letter 100% 2-sided 2-sided Collate To cancel printing, select [Cancel], and then press [Yes] in the confirmation screen. The Copying screen appears in the touch panel during printing. Plain 1 Top Edge Top Press the Stop key or [Cancel]. Top Tray Cancel Status 3-42 The current print job is cancelled. Reserve Next 08/08/2009 10:10 OPERATION GUIDE Basic Operation Quick Setup Screen In the initial screen for copying and sending (the screen which appears immediately after the Copy or Send key is first pressed after power-on), important and generally often used functions are registered from among the versatile functions of this machine. This initial screen is called Quick Setup Screen. Registration of functions in the Quick Setup Screen can be adjusted to suit your work environment for better efficiency. 3 Functions Available for Registration in the Quick Setup Screen Default registrations and the functions available for registration are as follows. Function Functions Available for Registration Default Registration Copying 1: 2: 3: 4: 5: 6: Paper Selection Zoom Density Duplex Combine Staple/Punch • • • • • • • • • • • Paper Selection Zoom Density Duplex Combine Staple/Punch Original Orientation Collate/Offset Original Image Original Size Continuous Scan Sending 1: 2: 3: 4: 5: 6: Zoom Scan Resolution FAX TX Resolution Density 2-sided/Book Original File Format • • • • • • • • • • • • Zoom Scan Resolution FAX TX Resolution Density 2-sided/Book Original File Format Original Size Sending Size Original Orientation Original Image Color Selection Continuous Scan OPERATION GUIDE 3-43 Basic Operation Function Document Box Functions Available for Registration Default Registration Document Storage 1: Color Selection 2: Resolution 3: Density 4: 2-sided/Book Original 5: Original Orientation 6: Original Image • • • • • • • • • • Color Selection Resolution Density 2-sided/Book Original Original Orientation Original Image Original Size Zoom Continuous Scan Storing Size Sending From Box 1: File Format 2: Delete after Transmitted 3: FAX TX Resolution 4: Sending Size • • • • File Format Delete after Transmitted FAX TX Resolution Sending Size Printing From Box 1: Paper Selection 2: Delete after Printed 3: Collate/Offset 4: Duplex 5: Staple/Punch 6: Combine • • • • • • Paper Selection Delete after Printed Collate/Offset Duplex Staple/Punch Combine Changing Registration Ready to copy. The following procedure is one example for replacing the registration of Density with Original Image in the Quick Setup Screen for copying. Copies Shortcut 1 Copy Image Shortcut 2 Place original. Shortcut 3 Auto Original Zoom Paper : --: 100% : --Preview Quick Setup Status 3-44 Paper Selection 2-sided >>2-sided Duplex Org./Paper/ Finishing 100% Normal 0 Zoom Shortcut 4 Density Shortcut 5 2 in 1 Combine Image Quality Off Staple/Punch Layout/Edit Shortcut 6 Advanced Setup 08/08/2009 10:10 1 Press the System Menu key. 2 Press [Copy], [Next] of Quick Setup Registration, and then [Change] of Original Image. OPERATION GUIDE Basic Operation 3 Copy - Original Image Register Original Image function on the Quick Setup screen. Press [Key 3] here as the key to set replacement location. Off Key 1 Key 2 Key 3 Key 4 Key 5 Key 6 3 Cancel Status OK 08/08/2009 10:10 4 OPERATION GUIDE Press [OK]. A confirmation screen appears. Press [Yes]. The Original Image Quality function will be newly registered. 3-45 Basic Operation Program (Copying and Sending) By registering sets of frequently used functions as a single program, you can simply press the program number as needed to recall those functions. You can also name the programs for easy identification when recalling. NOTE: Sending operation can be registered in the program as well. Up to 50 functions combining copying and sending can be registered in the program. If user login administration is enabled, you can only register functions by logging in with administrator privileges. Registering Programs Use the procedure below to register a program. The following procedure is an example of registering the copying function. 1 Press the Program key while the copy mode is accessed. 2 Press [Register] and press a number (01 to 50) for the program number. If entering Program screen from the Copy screen or Send screen, go to step 4. NOTE: If you select a program number already registered, the currently registered functions can be replaced with a new set of functions. 3 Check that [Copy] is selected, and press [Next]. 4 Enter the new program name and press [Register] to register the program. Recalling Programs Use the procedure below to recall a registered program. Program recalling. 01 FAX 1 06 02 FAX 2 07 03 08 04 09 05 10 Recall St 3-46 Register 1 Press the Program key. 2 Press [Recall] and press the key corresponding to the program number (01 to 50) to recall. Press the Quick No. Search key or [No.] to enter the program number directly for recalling. No. NOTE: If the program cannot be recalled, the Document Box or the form overlay specified in the program might have been deleted. Check the Document Box. Edit 08/08/2009 10:10 3 Place the originals and press the Start key. Copying is performed according to the registered program. OPERATION GUIDE Basic Operation Editing and Deleting Programs You can change program number and program name, or delete program. Use the procedure below to edit or delete a program. 1 Press the Program key. 2 Press [Edit] and press the key(s) corresponding to the program number (01 to 50) to change or delete. 3 To edit a program, use the procedure for registering a program and press [Change]. Then change the program number and program name and press [Register]. Choose [Yes] in the confirmation screen to change the program. To delete the program, press [Delete this Program]. Choose [Yes] in the confirmation screen to finally delete the program. OPERATION GUIDE 3-47 3 Basic Operation Registering Shortcuts (Copy, Send, and Document Box Settings) Add shortcuts in the Quick Setup screen for easy access to the frequently used functions. A function name linked to a registered shortcut can be changed as necessary. You can register up to 6 shortcuts for copying functions, sending functions, and functions set for document box. Adding Shortcuts Shortcut registration is performed in the setup screen of each function. Shortcuts can be registered for all functions in which [Add Shortcut] appears on the screen. Use the procedure below to register a shortcut. Copies Ready to copy. 1 After making the desired settings in the setup screen of each function, press [Add Shortcut]. 2 Press the keys corresponding to the shortcut number (01 to 06) to register. Memo Page Layout Off Place original. Layout A Top L to R Top R to L None Layout B Border Line Original Zoom Paper : --: 100% : --- Top Edge Top Top L to B Top R to B Preview Add Shortcut Cancel Status Original Orientation OK 08/08/2009 10:10 NOTE: If you select a shortcut number already registered, the currently registered shortcut can be replaced with a new one. 3 Enter the shortcut name and press [Register] to add the shortcut. Editing and Deleting Shortcuts Follow the steps as below to change shortcut number/name or delete shortcut. 1 In the setup screen of each function, press [Add Shortcut] in the bottom of the screen. 2 Press [Edit] and press the keys corresponding to the shortcut number (01 to 06) to change or delete. 3 To edit a shortcut, press [Change] to change the shortcut button number and name and press [OK] and then [Register]. Choose [Yes] in the confirmation screen to change the shortcut. To delete the shortcut, press [Delete this Shortcut]. Choose [Yes] in the confirmation screen to delete the shortcut. 3-48 OPERATION GUIDE Basic Operation Using the Internet Browser This section explains how to use the Internet browser. NOTE: To use the internet browser, internet browser must be set to [On] in Internet Browser Setting on page 8-58. 3 Launching and Exiting the Browser Use the procedure below to launch and exit the Internet browser. 1 Press the Application key. The application list screen appears. 2 Application Press [Internet Browser]. The Internet browser starts up. Internet Browser Status 08/08/2009 10:10 3 Use the browser screen to browse web pages. For information on how to use the browser screen, refer to Using the Browser Screen on page 3-50. 4 To exit the browser, press [X] (Close) and then press [Yes] in the exit confirmation screen. The application list screen reappears. NOTE: You can specify preferences such as the way the Internet browser screen is displayed. For details, refer to Internet Browser Setup (page 8-58). OPERATION GUIDE 3-49 Basic Operation Using the Browser Screen The operations available in the Internet browser screen are shown below. Search box Pressing the text box displays a keyboard. You can then perform a search by entering a keyword and pressing the [Search]. Title bar Displays the page title. Close Closes the Internet browser and returns you to the application list screen. Scroll bars These allow you to scroll the displayed page up, down, left and right by pressing [ ], [ ], [ ] or [ ] or by moving one of the slide bars with your finger. Security lock icon Displayed when you are viewing a protected page. Enter URL Search Menu Loader/Progress bar Shows the status of page loading. When the browser is loading a web page, the loader changes to an animated display. Menu Displays the browser setup menu. You can use this menu to specify the browser's display magnification, set the text encoding scheme and check the server certificate. Enter URL Use this display a desired web page by entering the URL for that page. Home page Displays your specified home page. You can set your home page in the Browser Preferences on page 8-58. Search (Search Internet/Retrieval in page) Displays a search menu in which you can select [Retrieval in page] or an Internet search site. Search Internet: Use the selected search site to search with the entered keyword. Retrieval in page: Search from the entered keyword in the currently displayed page. You can continue your search by pressing [SearchUp] or [SearchDown]. Reload Updates the page. Back/Forward Displays the previous page or the next page. NOTE: Pressing the Reset key while the Internet browser is displayed will exit the browser and return you to the application list screen without displaying the browser exit 3-50 OPERATION GUIDE 4 Copying Functions This chapter explains the functions available for copying. • • • • • • • • • • • • • • • • • • • • • • • • Original Size........................................................................................4-2 Paper Selection...................................................................................4-4 Mixed Sized Originals .........................................................................4-7 Original Orientation ...........................................................................4-10 Output Destination ............................................................................4-12 Combine Mode..................................................................................4-13 Margin/Centering Mode ....................................................................4-15 Border Erase.....................................................................................4-17 Booklet from Sheets..........................................................................4-19 Cover Mode ......................................................................................4-21 Form Overlay ....................................................................................4-22 Page Numbering ...............................................................................4-23 Memo Mode ......................................................................................4-25 Image Repeat/Double Copy..............................................................4-27 EcoPrint ............................................................................................4-29 Sharpness Adjust..............................................................................4-30 Continuous Scan...............................................................................4-31 Auto Image Rotation .........................................................................4-32 Negative Image.................................................................................4-32 Mirror Image......................................................................................4-33 Job Finish Notice ..............................................................................4-34 File Name..........................................................................................4-35 Priority Override ................................................................................4-35 Repeat Copy .....................................................................................4-36 OPERATION GUIDE 4-1 Copying Functions Original Size Specify the size of originals being scanned. Be sure to specify the original size when copying non-standard sizes. The following options are available. Item How to Select Sizes Have the size of original detected automatically, or select from the standard sizes. Inch models: Auto, Ledger, Legal, Letter, Letter-R, Statement, Statement-R, 8.5×13.5", Oficio II and 11×15" Select from the standard sizes not included in the Standard Sizes 1 . Inch models: A3, B4, A4, A4-R, B5, B5-R, A5, A5-R, B6, B6-R, A6-R, Folio, 8K, 16K and 16K-R Others Select from envelope, postcard or the custom sized originals*. Hagaki, Oufuku Hagaki, Custom 1 to 4 Size Entry Enter the size not included in the standard sizes 1 and 2**. Inch models Horizontal: 2 to 17" (in 0.01" increments), Vertical: 2 to 11.69" (in 0.01" increments) Standard Sizes 1 Standard Sizes 2 Metric models: Auto, A3, B4, A4, A4-R, B5, B5-R, A5, A5-R, B6, B6-R, A6-R and Folio Metric models: Ledger, Legal, Letter, Letter-R, Statement, Statement-R, 8.5×13.5", Oficio II, 11×15", 8K, 16K and 16K-R Metric models Horizontal: 50 to 432 mm (in 1 mm increments), Vertical: 50 to 297 mm (in 1 mm increments) * ** For instructions on how to specify the custom original sizes (Custom 1 to 4), refer to Custom Original Size Setup on page 8-4. The input units can be changed in the System menu. Refer to Switching Unit of Measurement on page 8-11. Use the procedure below to select the original size. 4-2 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Original Size]. OPERATION GUIDE Copying Functions 4 Copies Ready to copy. Press [Standard Sizes 1 ], [Standard Sizes 2 ], [Others] or [Size Entry] to select the original size. Original Size Standard Sizes 1 Place original. Standard Sizes 2 Auto Ledger Letter Letter Legal Statement Statement 11x15" 8.5x13.5" Others OficioII Original Zoom Paper : --: 100% : --- Size Entry Preview Cancel Add Shortcut Status 4 OK 08/08/2009 10:10 If [Size Entry] is selected, press [+] or [-] to specify the horizontal size (X) and the vertical size (Y). Press [# Keys] to enter the size directly using the numeric keys. Copies Ready to copy. Original Size Standard Sizes 1 Place original. X 17 Standard Sizes 2 # Keys Others Y Original Zoom Paper : --: 100% : --- (2.00 - 17.00) " Add Shortcut Status OPERATION GUIDE Press [OK]. 6 Press the Start key to start copying. (2.00 - 11.69) " 11 Size Entry Preview 5 # Keys Cancel OK 08/08/2009 10:10 4-3 Copying Functions Paper Selection Select the paper source that contains the required paper size. NOTE: Specify in advance the size and type of the paper loaded in the cassette (refer to Original/Paper Settings on page 8-4). Selecting the Cassette Use the procedure below to select the paper supply cassette. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Paper Selection]. 4 Press the key of the paper source corresponding to the required paper size. The cassette in which the paper is loaded is selected. Paper Selection Place original. Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 4-4 If [Auto] is selected, the paper matching the size of the original is selected automatically. Auto Letter Plain Letter Plain Ledger Plain MP Tray Setting 5 Press [OK]. 6 Press the Start key to start copying. Letter Plain Letter Plain Cancel OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions Selecting the Multi Purpose Tray Change the paper size and media type. The available paper sizes and media types are shown in the table below. Category Paper Size Item Standard Sizes 1 Standard Sizes 2 ** *** Choose from the standard size. Choose from the standard sizes not included in the Standard Sizes 1. Sizes Inch models: Ledger, Legal, Letter, Letter-R, Statement, 8.5×13.5", Oficio II and Executive 4 Metric models: A3, B4, A4, A4-R, B5, B5-R, A5-R, B6, B6-R, A6-R and Folio Inch models: A3, B4, A4, A4-R, B5, B5-R, A5-R, B6-R, A6-R, Folio, 8K, 16K and 16K-R Metric models: Ledger, Legal, Letter, Letter-R, Statement, 8.5×13.5", Oficio II, Executive, 8K, 16K and 16K-R Others Choose from non-standard sizes and custom sizes. ISO B5, Envelope #10 (Commercial #10), Envelope #9 (Commercial #9), Envelope #6 (Commercial #6 3/4), Envelope Monarch, Envelope DL, Envelope C5, Envelope C4, Hagaki, Oufuku Hagaki, Youkei 4, Youkei 2 and Custom 1 to 4* Size Entry Enter the size not included in the standard sizes 1 and 2**. Inch models Horizontal: 5.83 to 17" (in 0.01" increments), Vertical: 3.86 to 11.69" (in 0.01" increments) Metric models Vertical: 98 to 297 mm (in 1 mm increments), Horizontal: 148 to 432 mm (in 1 mm increments) Plain (105 g/m2 or less), Transparency, Rough, Vellum (64 g/m2 or less), Labels, Recycled, Preprinted***, Bond, Cardstock, Color, Prepunched***, Letterhead***, Thick (91 g/m2 or more), Envelope, High Quality, Custom 1 to 8*** Media Type * How to Select For instructions on how to specify the custom paper sizes (Custom 1 to 4), refer to Adding a Custom Size and Media Type for Paper to Print on page 8-4. The input units can be changed in the System menu. Refer to Switching Unit of Measurement on page 8-11. For instructions on how to specify the custom paper types 1 to 8, refer to Paper Weight on page 8-7. To print on preprinted or prepunched paper or on letterhead, refer to Special Paper Action on page 8-10. NOTE: You can conveniently select in advance the size and type of paper that will be used often and set them as default (refer to Paper Size and Media Type Setup for Multi Purpose Tray on page 8-6). OPERATION GUIDE 4-5 Copying Functions Use the procedure below to select the paper size and media type. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing], [Paper Selection] and then [MP Tray Setting]. 4 Press [Standard Sizes 1 ], [Standard Sizes 2 ], [Others] or [Size Entry] to select the paper size. Paper Selection - MP Tray Setting Standard Sizes 1 Standard Sizes 2 Ledger Letter Letter Legal Statement Executive 8.5x13.5" OficioII Others Size Entry Plain Media Type Cancel Status OK 08/08/2009 10:10 If you select [Size Entry], press [+] or [–] to specify X (horizontal) and Y (vertical) sizes. You can enter the size directly using the numeric keys after pressing [# Keys]. Copies Ready to copy. Original Size Standard Sizes 1 X (5.83 - 17.00) " 17 Standard Sizes 2 # Keys Others Y 5 Press [Media Type]. 6 Select paper type, and press [OK]. 7 Press [OK]. 8 Press [OK]. 9 Press the Start key to start scanning the originals. (3.86 - 11.69) " 11 Size Entry Plain Media Type # Keys Cancel Status OK 08/08/2009 10:10 10 When the machine is ready, the confirmation screen for the specified paper appears. Load the required paper in the multi purpose tray and press [Continue] to start copying. 4-6 OPERATION GUIDE Copying Functions Mixed Sized Originals Using the optional document processor, the originals of different sizes can be loaded in a batch and copied. In this operation, up to 30 originals of different sizes can be placed in the document processor at the same time. Supported Combinations of Originals Originals of the Same Width The supported combinations of originals are as follows. 4 Ledger and Letter (A3 and A4) Ledger Letter Letter Ledger Ledger and Letter-R (Folio and A4-R) Legal Letter-R Letter-R l B4 and B5 OPERATION GUIDE 4-7 Copying Functions Originals of Different Widths Place all originals of different widths. The supported combinations of originals are as follows. NOTE: When mixing the original sizes as using the following combination: Folio, A4-R, and B5-R, make sure to set the System Menu key -> Common Settings -> Original / Paper Settings -> Original Auto Detect to [On] for [Folio]. For more information, refer to Automatic Detection of Originals (Available for metric models only) on page 8-9. A3, B4, A4 and B5 B4, A4-R and B5 Folio, A4-R and B5-R 4-8 OPERATION GUIDE Copying Functions Selecting How to Copy Originals Select whether you wish to create individual copies on different size paper matching the original sizes or to produce all copies on the same size paper. NOTE: This function is available regardless of whether originals have the same width or not. The table below shows the finished document sizes for the different original size options. Option 4 Description Mixed Size Copies Originals are detected individually for size and copied to the same size paper as originals. Same Size Copies Originals are all copied to the same size paper. Use the procedure below to copy mixed size originals. 1 Press the Copy key. 2 Place originals on the document processor. IMPORTANT: When placing originals of different widths, be sure to flush them against the document width guide toward the back of the machine. Ready to copy. Copies 3 Press [Org./Paper/Finishing] and then [Mixed Size Originals]. 4 Select [Mixed Size Copies] or [Same Size Copies] as finish size. 5 Select the combination of originals from [Same Width] and [Different Width]. When [Same Size Copies] is selected, select [Long Edge Left] or [Short Edge Left] as the first original orientation. 6 Press [OK]. 7 Press the Start key to start copying. Mixed Size Originals Original Width Off Place original. Mixed Size Copies Same Size Copies Original Zoom Paper : --: 100% : --- Same Width D fferent Width Top Page Direction Long Edge Left Short Edge Left Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 4-9 Copying Functions Original Orientation Select the original orientation to use the following functions. • Zoom (XY Zoom) • Duplex • Margin/Centering originals • Border erase • Combine mode • Memo mode • Page numbering • Booklets • Stapling/Punch (optional feature) * If [On] is selected as the Orientation Confirmation on page 8-15 setting in the System Menu, the selection screen for original orientation appears when you select any of the above functions. When placing originals on the platen Original [Top Edge Top] [Top Edge Left] When placing originals on the optional document processor Original [Top Edge Top] [Top Edge Left] NOTE: To change the default setting for the original orientation, refer to Original Orientation on page 8-15. 4-10 OPERATION GUIDE Copying Functions Use the procedure below to select the orientation when placing the originals on the platen. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Original Orientation]. 4 Select [Top Edge Top] or [Top Edge Left] as the way the original is oriented. 5 Press [OK]. 6 Press the Start key to start copying. Original Orientation Select the orientation of the original document's top edge. Place original. Original Zoom Paper : --: 100% : --- Top Edge Top Top Edge Left Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 4-11 4 Copying Functions Output Destination You can use the procedure below to select an output destination such as the optional document finisher for your copies. NOTE: Optional output destinations include the job separator, built-in finisher, document finisher, 3,000 sheet document finisher, and mailbox. The table below shows the available output destinations. Destination Description Top tray Top tray of the machine (where copies are stored) Finisher Tray* Tray of the optional built-in finisher or document finisher Tray A, Tray B*, Tray C* Trays A to C in the optional 3,000 sheet document finisher Job Separator Tray Optional job separator Tray 1 to 7* Trays 1 to 7 in the optional mailbox (tray 1 is the top tray) * Copy output orientation can be selected either as face-up (print facing up) or facedown (print facing down). NOTE: To change default destination for copies, refer to Paper Output on page 8-14 for details. Use the procedure below to select the output destination. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Org./Paper/Finishing] and then [Paper Output]. 4 Select the output destination for finished copies. When you select [Finisher Tray], [Tray B], [Tray C] or [Tray 1] to [Tray 7], select the orientation of output copy, Face Up (print facing up) or Face Down (print facing down). Paper Output Face Up Place original. Original Zoom Paper : --: 100% : --- Face Down Top Tray Tray A Tray B Tray C Job Separator Tray Tray 1 Tray 2 Tray 3 Tray 4 Tray 5 Tray 6 Tray 7 5 Press [OK]. 6 Press the Start key to start copying. Preview Add Shortcut Status 4-12 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions Combine Mode This mode allows you to copy 2 or 4 originals combined onto a single page. 2-in-1 mode or 4-in-1 mode. The page boundary of each original can be indicated. NOTE: Combine mode is available for the copy paper sizes of A3, B4, Folio, A4, A4-R, B5, B5-R, A5-R, Ledger, Legal, Oficio II, 8.5×13.5", Letter, Letter-R, Statement-R, 8K, 16K and 16K-R. 2-in-1 Mode For copying two originals onto a single sheet. This mode can be used with Duplex mode to copy four originals onto one sheet. The following 2-in-1 options and output orientations are available. Original Copy Orientation of Original Platen Document processor NOTE: When placing the original on the platen, be sure to copy the originals in page order. 4-in-1 Mode For copying four originals onto a single sheet. This mode can be used with Duplex mode to copy eight originals onto one sheet. The following 4-in-1 options and output orientations are available. Original Copy Orientation of Original Platen Document processor NOTE: When placing the original on the platen, be sure to copy the originals in page order. OPERATION GUIDE 4-13 4 Copying Functions Types of Page Boundary Lines The following types of the boundary lines are available. None Solid Dotted Borders (Cropmark) The procedure for using Combine mode copying is explained below. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Combine]. 4 Press [2 in 1] or [4 in 1], and choose the page layout of Layout. 5 Press [Border Line] to choose the type of the lines to indicate page boundaries. Press [OK]. 6 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 7 Press [OK]. 8 Press the Start key. Copying begins. Combine Layout Off Place original. 2 in 1 Right then Down Left then Down None 4 in 1 Border Line Original Zoom Paper : --: 100% : --- Top Edge Top Down then Right Down then Left Preview Add Shortcut Status Cancel Original Orientation OK 08/08/2009 10:10 If the original is placed on the platen, replace the original and press the Start key. After scanning all originals, press [Finish Scan] to start copying. 4-14 OPERATION GUIDE Copying Functions Margin/Centering Mode Shift the original image to make space on the copy for binding on the left (right) or top (bottom) side. When you copy onto paper different from the original size, you can center the original image on the paper. The following margin widths are available. Input units Margin Width Inch Models -0.75 to 0.75" (in 0.01" increments) Metric Models -18 mm to 18 mm (in 1-mm increments) 4 Margin on the Back Side When duplex copying, you can also specify the margin on the back side. Auto When [Auto] is selected, an appropriate margin is applied automatically on the rear page depending on a margin specified for the front page and a binding orientation. Separate Front/Back Margins Enables you to specify the front and back settings separately. NOTE: You can set the default margin width. Refer to Margin Default on page 8-21 for details. Use the procedure below to make copies with margins. Copies Ready to copy. Left/Right (-18 - +18) 0 Place original. (-0.75 - +0.75) " Add Shortcut Status OPERATION GUIDE 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Margin/Centering]. 4 Press [Margin] to select the copy with margin. For duplex copying, press [Back Page] and select [Auto] or [Manual]. Back Page 0 : --: 100% : --Preview Auto # Keys Top/Bottom Original Zoom Paper " Margin Centering Press the Copy key. Use [+] or [–] to enter the margins for Left/Right and Top/Bottom. Press [# Keys] to use the numeric keys for entry. Margin/Centering Off 1 Top Edge Top # Keys Cancel Original Orientation OK 08/08/2009 10:10 4-15 Copying Functions If you selected [Auto], press [OK]. If you pressed [Manual], enter the margins in the displayed screen and then press [OK]. Copies Ready to copy. Margin/Centering - Back Page Auto Place original. Left/Right (-0.75 - +0.75) " 0.25 Manual # Keys Top/Bottom Original Zoom Paper (-0.75 - +0.75) " 0.25 : --: 100% : --Preview # Keys Add Shortcut Cancel Status OK 08/08/2009 10:10 Press [Centering] to center the original image on the paper. Copies Ready to copy. Margin/Centering Off Place original. 5 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 6 Press [OK]. 7 Press the Start key to start copying. Margin Centering Original : --- Zoom Paper : 100% : --- Top Edge Top Original Orientation Preview Add Shortcut Status 4-16 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions Border Erase Use Border Erase to remove black shadows that appear around the outside of the original when making copies. The following options can be selected. Border Erase Sheet Erases black borders around the single sheet original. 4 Original Copy Border Erase Book Erases black borders around the edges and in the middle of the original such as a thick book. You can specify the widths individually to erase the borders around the edges and in the center of the book. Original Copy Individual Border Erase Specify border erase widths individually for all edges. Original Copy In each option, the available ranges are as below. Input units Border Erase Range Inch Models 0 to 2"(in 0.01" increments) Metric Models 0 mm to 50 mm (in 1-mm increments) NOTE: To specify the default width value of Border Erase, refer to Border Erase Default on page 8-20 for details. OPERATION GUIDE 4-17 Copying Functions Border Erase to Back Page When scanning a 2-sided original, this allows you to erase the borders on the back of the original. The table below shows the available settings. Item Detail Same as Front Page Border Erase performed using the same setting as the front page Do Not Erase No Border Erase performed on the back page NOTE: You can change the default setting for Border Erase to Back Page. For details, refer to Paper Selection on page 8-26. Use the procedure below to erase borders when copying. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Border Erase]. 4 Select [Border Erase Sheet] to erase borders for an individual sheet or [Border Erase Book] to erase borders for a book. Border Erase (-0.75 - +0.75) " Border Off 0.25 Border Erase Book Original : --- Zoom Paper : 100% : --- Use [+] or [–] to enter the width in Border or Gutter. Press [# Keys] to use the numeric keys for entry. Border Erase Sheet Place original. Same as Front Page # Keys (-0.75 - +0.75) " Gutter Back Page 0.25 Individual Border Erase Preview # Keys Add Shortcut Cancel OK Status 08/08/2009 10:10 Press [Individual Border Erase] to select the individual border erase. Copies Ready to copy. Border Erase (0.00 - 2.00) Off Place original. Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 4-18 Top 0.25 " Border Erase Sheet Bottom 0.25 " Border Erase Book Left 0.25 " Individual Border Erase Right 0.25 " Use [+] or [–] to enter the width in Top, Bottom, Left or Right. Press [# Keys] to use the numeric keys for entry. Same as Front Page Back Page Press [Original Orientation] to select the original orientation from either [Top Edge Top] or [Top Edge Left]. Then press [OK]. Top Edge Top # Keys Cancel Original Orientation OK 08/08/2009 For 2-sided originals, press [Back Page] and then press [Same as Front Page] or [Do Not Erase]. 10:10 5 Press [OK]. 6 Press the Start key to start copying. OPERATION GUIDE Copying Functions Booklet from Sheets The Booklet copying option allows you to copy sheet originals and produce booklets such as small brochures or pamphlets. A booklet, such as a magazine, is made by folding at the center. You can copy the cover page onto colored paper or thick paper. Paper for the cover is supplied from the multi purpose tray. To feed the cover paper from the cassette, refer to Paper Source for Cover Paper on page 8-10. NOTE: Using the optional 3,000 sheet document finisher and the folding unit enables you to saddle stitch your copies (fold them in two with staples in the center). This is limited to the A3, B4, A4-R, Ledger, Legal, Letter-R. The supported original and paper sizes are as follows. Type of Original One-sided original, Two-sided original Book original * Original Size Paper Size All* A3, B4, A4, A4-R, B5, B5-R, A5, A5-R, Ledger, Legal, Letter and Letter-R All* A3, B4, A4-R, Ledger, Legal and Letter-R A3, B4, A4-R, B5-R, A5-R, Ledger, Letter-R and 8K A4, A4-R, B5, B5-R, Letter and Letter-R A3, B4, A4-R, B5-R, A5-R, Ledger and Letter-R A4-R and Letter-R Except for custom sized originals. For binding on the left side The folded copies can be read from left to right. Original Copy For binding on the right side The folded copies can be read from right to left. Original Copy For top binding The folded copies can be read from top to bottom. Original OPERATION GUIDE Copy 4-19 4 Copying Functions The procedure for using Booklet copying is explained below. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Booklet]. 4 Press [1-sided>>Booklet] to produce a booklet from single-sided originals. Booklet Off Original Place original. 1-sided >>Booklet Press [2-sided>>Booklet] to produce a booklet from two-sided originals. Off Binding Left/Right Cover Binding Top Off 2-sided >>Booklet Original Zoom Paper : --: 100% : --Preview Add Shortcut Status Book >>Booklet Press [Book>>Booklet] to produce a booklet from an open book original. Finishing Binding Left Binding Right Binding Top Cancel Saddle Stitch Top Edge Top Original Orientation OK 08/08/2009 10:10 5 If you selected [2-sided>>Booklet] or [Book>>Booklet], choose the binding orientation in Finishing. If you selected [1-sided>>Booklet], choose the binding orientation in Finishing. 6 If you choose [1-sided>>Booklet], [2-sided>>Booklet], or [Book>>Booklet] you can add the cover. Press [Cover], select [Cover] and press [OK]. 7 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. 8 If the optional 3,000 sheet document finisher and folding unit are installed, the [Saddle Stitch] option is displayed. To use saddle stitching, press [Saddle Stitch] and then press [Bind and Fold]. You can saddle stitch up to 16 sheets (64 pages). 9 Press [OK]. 10 Platen and press the Start key. Copying begins. NOTE: When using the platen, be sure to place the originals in page order. If the originals are placed on the platen, consecutively replace each original after pressing the Start key. After scanning all originals, press [Finish Scan] to start copying. 4-20 OPERATION GUIDE Copying Functions Cover Mode Add a cover to the finished copies. You can copy the first page and/or the last page onto colored paper or thick paper fed from the different paper source than the regular one. The following two options are available. Paper for the cover is supplied from the multi purpose tray. To feed the cover paper from the cassette, refer to Paper Source for Cover Paper on page 8-10. Type of Cover Description Front Cover First page of the originals is copied on a different paper. Front and Back Covers First page and last page of the originals are copied on different paper. 4 The procedure for using Cover mode copying is explained below. Ready to copy. Copies Cover Place original. Original Zoom Paper : --: 100% : --- 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Cover]. 4 Press [Front Cover] or [Front and Back Covers]. 5 Press [OK]. 6 Press the Start key. Copying begins. Print cover pages on the different type of paper, using a different paper source. Select either [Front Cover] or [Front and Back Covers]. *Set paper source for cover in System Menu. Off Front Cover Front and Back Covers Preview Add Shortcut Status Cancel OK 08/08/2009 10:10 If the originals are placed on the platen, consecutively replace each original after pressing the Start key. After scanning all originals, press [Finish Scan] to start copying. OPERATION GUIDE 4-21 Copying Functions Form Overlay Copy the original images onto the form. Once you scan and register the form, the form is overlaid onto the original. You can also use a form that is already registered in the machine's memory. Forms Original Copy NOTE: To register a form in advance, refer to Form for Form Overlay Box on page 6-17 for details. Follow the steps as below for form overlay. Ready to copy. Copies 1 Press the Copy key. 2 Press [Layout/Edit] and then [Form Overlay]. 3 Press [Scan New Form] to use the first page of originals as a form. Form Overlay Off Place original. Density (10 - 100) 10 % NOTE: Press [+] or [–] in [Density] to adjust the density of the form. Choose from ten levels in 10% increments. Select Stored Form Scan New Form Original : --- Zoom Paper : 100% : --- None Select Form Preview Add Shortcut Cancel OK 08/08/2009 Status 10:10 To use the forms already registered, press [Select Stored Form]. Press [Select Form] to display the document boxes that store documents which can be used as a form. Select the desired form from the list and press [OK]. Copies Ready to copy. Form Overlay - Select Form Document Box Box Name Up Form for Form Overlay Custom Box Detail NOTE: To return to a higher level folder, press [Up]. 1/1 Preview Open Cancel Status OK 08/08/2009 10:10 4 Press [OK]. 5 Place the originals. Place the original for the form on top of the other originals. When using the optional document processor, the first page of the originals should be placed on the top. 6 4-22 Press the Start key to start copying. OPERATION GUIDE Copying Functions Page Numbering Number multiple pages of originals in sequential order. The formats for numbering are [-1-], [P.1] or [1/n]. The format [1/n] prints the total number of pages in the place of n. Select Top Left, Top Middle, Top Right, Bottom Left, Bottom Middle or Bottom Right as the page numbering position. 4 Original [ – 1 –] [P.1] [1/n] Use the procedure below to insert page numbers on your copies. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals in the document processor or on the platen. 3 Press [Layout/Edit] and then [Page #]. 4 Select the numbering format from [-1-], [P.1] or [1/n]. 5 Select the page numbering position. 6 To start page numbering from a page other than the first page, press [+] or [–] of 1st Page and select the starting page. You can also enter the number with the numeric keys after pressing [# Keys]. 7 To start the numbering with a number other than 1, press [+] or [–] of Start Number and enter the starting number. You can also enter the number with the numeric keys after pressing [# Keys]. 8 If you do not want page numbering through to the last page, press [Last Page]. Select Manual and use [+] or [-] to enter the final page to be numbered (a negative number of pages counting backwards from the last page). Then press [OK]. You can set a value up to -10. You can also enter the number with the numeric keys after pressing [# Keys]. Page # Auto Position Off -1- Top Left Top Middle Top Right Bottom Left Bottom Middle Bottom Right Last Page Auto P.1 1st Page Start # (1 - 10) (1 - 999) 1 1/n Denom nator # 1 Top Edge Top # Keys # Keys Cancel Status OPERATION GUIDE Original Orientation OK 08/08/2009 10:10 4-23 Copying Functions 9 The total number of pages n in the format [1/n] can be changed manually. Press [Denominator #] and select [Manual]. Press [+] or [–] to enter the total number of pages and press [OK]. You can also enter the number with the numeric keys after pressing [# Keys]. 10 Press [Original Orientation] to choose orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Press [OK]. 11 Press [OK]. 12 Press the Start key to start copying. 4-24 OPERATION GUIDE Copying Functions Memo Mode Delivers copies with a space for adding notes. You can also copy two originals onto the same sheet with a space or add lines to indicate page boundaries. NOTE: Memo mode is available for the copy paper sizes of Ledger, Legal, Oficio II, 8.5×13.5", Letter, Letter-R, Statement-R, A3, B4, Folio, A4, A4-R, B5, B5-R, A5-R, 8K, 16K and 16K-R. Layout A Reduces images of each original page for printing onto half of a page, leaving the other half blank for notes. Original Copy Layout B Reduces images of two original pages for copying onto half of a single page, leaving the other half blank for notes. Original OPERATION GUIDE Copy 4-25 4 Copying Functions Types of Page Boundary Lines The following boundary lines are available. None Solid Dotted Borders (Cropmark) Use the procedure below to insert page boundary lines on your copies. Copies Ready to copy. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then [Memo Page]. 4 Press [Layout A] or [Layout B]. Select the page layout from Layout. 5 Press [Border Line] to select the page boundary line. Press [OK]. 6 Press [Original Orientation] to select orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Press [OK]. 7 Press [OK]. 8 Press the Start key to start copying. Memo Page Layout Off Place original. Layout A Top L to R Top R to L None Layout B Border Line Original Zoom Paper : --: 100% : --- Top Edge Top Top L to B Top R to B Preview Add Shortcut Status 4-26 Cancel Original Orientation OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions Image Repeat/Double Copy Tiles the 1 copied sheet with an original image. You can also specify the area of the original to repeat. Image Repeat Copies the original image multiple times onto 1 sheet at a specified magnification. You can also specify how much of the original is repeatedly copied. Original Copy Double Copy Makes 2 copies of the same original on a single sheet. For example, you can double-copy an A4 original onto an A3 sheet which you then cut in half to make 2 copies that are identical to the original. Original Copy Follow the steps as below to use Image Repeat/Double Copy. Ready to copy. Copies 1 Press Copy key. 2 Place the originals on the platen. 3 Press [Layout/Edit] and then press [Image Repeat]. 4 Press [Zoom Priority]. To make double copies, press [Double Copy] and proceed to step 8. Image Repeat (25 - 400) Off 100 Place original. Double Copy Original : --- Zoom Paper : 100% : --- % Zoom Priority Add Shortcut OPERATION GUIDE Press [+] or [–] to set the zoom size. Press [# Keys] to enter with numeric keys. Off 6 Specify Repeat Area Preview Status 5 # Keys Cancel To set the area of the original to be repeated, press [On] for Specify Repeat Area. OK 08/08/2009 10:10 4-27 4 Copying Functions 7 Press [+] or [–] to input the area of the original to be repeated. With metric models, you can enter the border width directly using the numeric keys after pressing [#Keys]. Y1: Length from top left of platen to top edge of repeat area X1: Length from Height from top left of platen to left edge of repeat area Y2: Height of repeat area X2: Width of repeat area 4-28 8 Press [OK]. 9 Press the Start key. Copying begins. OPERATION GUIDE Copying Functions EcoPrint Use EcoPrint to save toner when printing. Use this function for test copies or any other occasion where high quality print is unnecessary. The procedure for making copies using EcoPrint is explained below. Ready to copy. Copies EcoPrint Place original. Original Zoom Paper 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Image Quality] and then [EcoPrint]. 4 Press [On]. 5 Press [OK]. 6 Press the Start key to start copying. 4 Conserve toner when printing. Use EcoPrint for test copies and other situations where high-quality copies are not necessary. : --: 100% : --- Off On Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 4-29 Copying Functions Sharpness Adjust Adjust the sharpness of image outlines. When copying penciled originals with rough or broken lines, clear copies can be taken by adjusting sharpness toward [Sharpen]. When copying images made up of patterned dots such as magazine photos, in which moire* patterns appear, edge softening and weakening of the moire effect can be obtained by setting the sharpness toward [Unsharpen]. * Patterns that are created by irregular distribution of halftone dots. Follow the steps below to adjust sharpness. Ready to copy. Copies 1 Press Copy key. 2 Place the originals on the platen. 3 Press [Image Quality] and then Press [Sharpness]. 4 Press [-3] to [3] (Unsharpen - Sharpen) to adjust the sharpness. 5 Press [OK]. 6 Press the Start key. Copying begins. Sharpness Place original. Unsharpen -3 Original : --- Zoom Paper : 100% : --- Sharpen -2 -1 0 +1 +2 +3 Preview Add Shortcut Status 4-30 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions Continuous Scan When a large number of originals cannot be placed in the document processor at one time, the originals can be scanned in separate batches and then copied as one job. With this function, originals are scanned until you press [Scan Finish]. Any of the following settings can be changed during scanning. • Original size selection • Zoom • Original orientation • Border erase • Image quality selection • Density • Type of original (2-sided/book original) • Color Selection 4 If you use Job Build, you can insert a blank paper during scanning or a blank page during duplex copying. The procedure for making copies using Continuous Scan is explained below. Ready to copy. Copies 1 Press the Copy key. 2 Press [Advanced Setup] and then [Continuous Scan]. 3 If Continuous Scan is selected, press [On]. If Job Build is selected, press [Job Build] and select desired binding orientation. Continuous Scan Off Place original. Select desired binding orientation. On 4 Press [OK]. 5 Place the originals in the document processor or on the platen and press the Start key. Job Build Original Zoom Paper : --: 100% : --- Binding Left Preview Add Shortcut Binding Right Binding Top Cancel OK 08/08/2009 Status Scan next original(s). Place the originals and press Start key. Press [Finish Scan] to start copying. Job No.: 000021 Job Name: doc20080505113414 10:10 Copies User Name: ----- Scanner Setting If [Job Build] is selected, the next page can be changed. Press [Sheet Insertion] to insert a blank paper. Press [Next Copy: On Back] in duplex copying to print the next page on back page. Finishing pages Original Size 2-sided/Book Original Density Original Orientation Original Image Next Copy: On Front Border Erase Zoom Next Copy: On Back Sheet Insertion 1/2 Cancel Status Finish Scan 08/08/2009 10:10 6 Place the next original and press the Start key. Repeat these steps to scan the remaining originals. After scanning all originals, press [Finish Scan] to start copying. OPERATION GUIDE 4-31 Copying Functions Auto Image Rotation Automatically rotates the image when the sizes of the original and the loaded paper matches but the orientations are different. The images will be rotated 90° counter-clockwise prior to copying. NOTE: To set Auto Image Rotation as the default mode, refer to Auto Image Rotation on page 8-21. The procedure for making copies using Auto Image Rotation is explained below. 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Auto Image Rotation]. 4 Press [On] to select Auto Image Rotation. 5 Press [OK]. 6 Press the Start key to start copying. Negative Image Inverts black and white portions of the image for printing. NOTE: This function is only available for black and white copy mode. Use the procedure below to make negative image copies. 4-32 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Negative Image]. 4 Press [On] to select Negative Image. 5 Press [OK]. 6 Press the Start key to start copying. OPERATION GUIDE Copying Functions Mirror Image Copies the mirrored image of the original. NOTE: This function is only available for black and white copy mode. Use the procedure below to make mirror image copies. OPERATION GUIDE 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Mirror Image]. 4 Press [On] to select Mirror Image. 5 Press [OK]. 6 Press the Start key to start copying. 4 4-33 Copying Functions Job Finish Notice Sends a notice by e-mail when a job is completed. User can be notified of the completion of a copy job while working at a remote desk, saving the time spent waiting beside the machine for copying to finish. NOTE: PC should be configured in advance so that E-mail can be used. Example of Job Finish Notice To: [email protected] Subject: 1234 Job end report mail Job No.: 000002 Result: OK End Time: Wed 27 Apr 2005 14:56:08 File Name: doc27042005145608 Job Type: Copy -----------------------------------------------1234 Use the procedure below to enable job finish notification when making copies. 1 Press the Copy key. Ready to copy. Copies 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Job Finish Notice]. 4 To select the destination from the address book, press [Address Book] on the left of the screen and then press [Address Book] in the next screen. Select the destination to be notified, then press [OK]. You can view information on the notification destination by pressing [Detail]. Job Finish Notice Off Destination Address Book User A Detail [email protected] Address Entry Detail Add Shortcut Address Book Cancel OK 08/08/2009 Status Ready to copy. 10:10 To directly enter the E-mail address, press [Address Entry]. Press [E-mail Address], enter the address and press [OK]. Copies Job Finish Notice Off Address Book E-mail Address Address Entry Add Shortcut Status 4-34 Cancel 5 Press [OK]. 6 Press the Start key to start copying. Upon completion of the job, an E-mail notice is sent to the selected destination. OK 08/08/2009 10:10 OPERATION GUIDE Copying Functions File Name Names a copy job. Add other information such as date and time or job number as necessary. You can check a job history or job status using the job name, date and time, or job number specified here. Use the procedure below to assign a name to your copy job. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [File Name Entry]. 4 Press [File Name], enter the name for a copy job, and press [OK]. File Name Entry To add date and time, press [Date and Time]. To add job number, [Job No.]. Added information is displayed in Additional Info. Add a file name. Additional information such as Job No. and Date and Time can also be set. File Name doc Additional Info Job No. Job No. NOTE: The maximum length of the file name is Date and Time Add Shortcut Status 32 characters. Cancel OK 08/08/2009 10:10 5 Press [OK]. 6 Press the Start key to start copying. Priority Override Suspends a current job and gives the selected job priority for copying. The suspended job resumes after Priority Override copying is finished. NOTE: The current job that is selected as Priority Override cannot be suspended. The procedure for using Priority Override is explained below. OPERATION GUIDE 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Priority Override]. 4 Press [On] to select Priority Override. 5 Press [OK]. 6 Press the Start key. The current copy job is suspended and the copy job selected in Priority Override starts. The suspended job resumes after Priority Override copying is finished. 4-35 4 Copying Functions Repeat Copy Enable additional copies in the desired quantity as necessary after a copy job is completed. For confidential documents, you can set up a pass code for the use of Repeat Copy. In such a case, the correct pass code must be entered when using Repeat Copy or copies will not be delivered. IMPORTANT: A Repeat Copy job is cleared when the main power switch is turned off. Repeat Copy is not available when the machine is equipped with the optional Data Security Kit. Repeat Copy cannot be used when the maximum number of Repeat Copy jobs to retain in the document box is set to zero (refer to Maximum Number of Repeat Copy Jobs Retained on page 4-37). You can select Repeat Copy as default setting. Refer to Repeat Copying on page 8-23. Giving a file name to a copy job will facilitate identification of the data when copying (refer to File Name on page 4-35). Selecting Repeat Copy Use the procedure below to select repeat copying. Ready to copy. Copies 1 Press the Copy key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Repeat Copy]. 4 Press [On]. To register a password, press [# Keys] and enter a 4-digit password. Repeat Copy Off Password(4digits) Place original. On IMPORTANT: If you forget the pass code, Repeat Copy will be unavailable. Make a note of the pass code beforehand if necessary. # Keys Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 4-36 Cancel OK 08/08/2009 10:10 5 Press [OK]. 6 Press the Start key to start copying and register this job as a Repeat Copy job. OPERATION GUIDE Copying Functions Outputting Repeat Copy Jobs The Repeat Copy jobs are stored in the Document Box. Refer to Job Box on page 3-33 to print out the Repeat Copy jobs. Maximum Number of Repeat Copy Jobs Retained You can use the procedure below to change the maximum number of copy jobs that can be retained in the document box. Use the procedure below to change the maximum number of copy jobs retained. Document Box/Removable Memory - Repeat Copy Job Retention 4 1 Press the System Menu key. 2 Press [Document Box/Removable Memory] and then [Next] of Job Box. 3 Press [Change] of Repeat Copy Job Retention. 4 Use the [+] or [-] key to enter the maximum retention number. Set the maximum number of repeat copy jobs to retain. Use [-]/[+] or the numeric keys to enter a number. *Set this number to 0 to not retain any jobs. You can also enter the number from the numeric keys. (0 - 50) 32 A number between 0 and 50 can be entered as the number of retained jobs. job(s) NOTE: If you enter a value of 0 (zero), you cannot use Cancel Status OK 08/08/2009 10:10 the Repeat Copy function. 5 OPERATION GUIDE Press [OK]. 4-37 Copying Functions 4-38 OPERATION GUIDE 5 Sending Functions This chapter explains the functions available for sending originals. • • • • • • • • • • • • • • • • • • • • • • • • • • • Original Size Selection........................................................................5-2 Sending Size Selection .......................................................................5-3 Zoom...................................................................................................5-5 Centering ............................................................................................5-6 Mixed Sized Originals .........................................................................5-7 1-sided/2-sided Selection..................................................................5-10 Original Orientation ...........................................................................5-11 File Format........................................................................................5-12 File Separation..................................................................................5-13 PDF Encryption Functions ................................................................5-14 Image Quality....................................................................................5-16 Adjusting Density ..............................................................................5-17 Scan Resolution................................................................................5-18 Sharpness.........................................................................................5-19 Background Density Adjustment.......................................................5-20 Color / Grayscale / Black and White Selection .................................5-21 Continuous Scan...............................................................................5-22 Border Erase.....................................................................................5-23 Enter Document Name/File Name ....................................................5-25 Enter E-mail Subject and Body .........................................................5-26 WSD Scan ........................................................................................5-27 Job Finish Notice ..............................................................................5-29 Send and Print ..................................................................................5-30 Send and Store .................................................................................5-30 FTP Encrypted TX ............................................................................5-31 Color Type.........................................................................................5-31 About Color Profiles ..........................................................................5-32 OPERATION GUIDE 5-1 Sending Functions Original Size Selection Select the size of originals that will serve as the basis for scanning. Be sure to select the original size when using originals of nonstandard sizes. Choose the original size from the following groups of original size. Item Detail Standard Sizes 1 Select from automatic detection and standard sizes. Size Inch models: Auto, Ledger, Legal, Letter, LetterR, Statement, Statement-R, 8.5×13.5", Oficio IIR, 11×15" Metric models: Auto, A3, B4, A4, A4-R, B5, B5R, A5, A5-R, B6, B6-R, A6-R, Folio Standard Sizes 2 Select from standard sizes except Standard Sizes 1 . Inch models: A3, B4, A4, A4-R, B5, B5-R, A5, A5-R, B6, B6-R, A6-R, Folio, 8K, 16 K, 16K-R Others Select from Hagaki and Custom Original Size *. Hagaki, Oufuku Hagaki, Custom 1 to 4 Size Entry Enter the size that is not indicated in Standard Sizes 1 and 2**. Inch models Horizontal: 2 to 17" (in 0.01" increments), Vertical: 2 to 11.69" (in 0.01" increments) Metric models: Ledger, Legal, Letter, Letter-R, Statement, Statement-R, 8.5×13.5", Oficio II-R, 11×15", 8K, 16K, 16K-R Metric models Horizontal: 50 to 432 mm (in 1 mm increments), Vertical: 50 to 297 mm (in 1 mm increments) * ** Regarding the setting method of Custom Original Size (Custom 1 to 4), refer to Custom Original Size Setup on page 8-4. The input units can be changed in the System menu. Refer to Switching Unit of Measurement on page 8-11. Use the procedure below to select the original size when sending scanned images. 5-2 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [Original Size]. OPERATION GUIDE Sending Functions Ready to send. 4 Destination Place original. Press [Standard Sizes 1], [Standard Sizes 2], [Others], or [Size Entry] to select original size. Original Size Standard Sizes 1 Place original. Standard Sizes 2 Auto Ledger Letter Letter Legal Statement Statement 11x15" 8.5x13.5" Others OficioII Original Zoom Paper : --: 100% : --- Size Entry Preview Add Shortcut Cancel OK Status 08/08/2009 Ready to send. 10:10 When you have selected [Size Entry], press [+] or [-] to set the sizes of X (horizontal) and Y (vertical). By pressing [# Keys], you can use the numeric keys. Destination Place original. Original Size Standard Sizes 1 Place original. X (2.00 - 17.00) " 17 Standard Sizes 2 # Keys Others Original Zoom Paper : --: 100% : --- 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. (2.00 - 11.69) " Y 11 Size Entry Preview # Keys Add Shortcut Cancel Status OK 08/08/2009 10:10 Sending Size Selection Select the sending size (the size of image to be sent). The table below lists the sizes. Item Detail Standard Sizes 1 Select from Same as Original Size or Standard Size. Size Inch models: Same as Original Size, Ledger, Legal, Letter, Statement, 8.5×13.5", Oficio II, 11×15" Metric models: Same as Original Size, A3, B4, A4, B5, A5, B6, A6, Folio Standard Sizes 2 Others OPERATION GUIDE Select from standard size except Standard Sizes 1. Inch models: A3, B4, A4, B5, A5, B6, A6, Folio, 8K, 16K Select from Hagaki. Hagaki, Oufuku Hagaki Metric models: Ledger, Legal, Letter, Statement, 8.5×13.5", Oficio II, 11×15", 8K, 16K 5-3 5 Sending Functions Relationship between Original Size, Sending Size, and Zoom Original Size (page 5-2), Sending Size, and Zoom (page 5-5) are related to each other. Refer to the following table. Original Size and the size you wish to send as are the same different Original Size Specify as necessary Specify as necessary Sending Size Select [Same as Original] Select the required size Zoom Select [100%] (or [Auto]) Select [Auto] NOTE: When you select Sending Size that is different from Original Size, and select the Zoom [100%], you can send the image as the actual size (No Zoom). Use the procedure below to select the size for transmission when sending scanned images. Ready to send. Destination 1 Press the Send Key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [Sending Size]. 4 Press [Standard Sizes 1], [Standard Sizes 2], or [Others] to select the sending size. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Sending Size Standard Sizes 1 Place original. Standard Sizes 2 Same as Original Size Ledger Letter Legal Statement 11x15" 8.5x13.5" OficioII Others Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 5-4 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Zoom Scans the original by automatically zooming it depending on the sending size. The table below lists the available options. Item Detail 100% No Zoom (to be scanned at actual size) Auto Zoomed automatically according to the specified sending size. NOTE: When zooming in or out, see Sending Size Selection on page 5-3 when selecting the sending size. Depending on the combination of original size and sending size, the image is placed at the edge of the paper. To center the image vertically and horizontally on the page, use the centering setting described in Centering on page 5-6. Use the procedure below to enlarge or reduce the original to match the transmission size. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Select the transmission size. 4 Press [Advanced Setup] and then [Zoom]. 5 Press [100%] or [Auto]. 6 Press [OK]. 7 Specify the destination, and press the Start key to start sending. Place original. Zoom Place original. Original Zoom Paper Enlarge or reduce original when scanning. [100%]: Scan at actual size. [Auto]: Enlarge or reduce to match sending size/storing size. : --: 100% : --- 100% Auto Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 5-5 5 Sending Functions Centering When you have scanned the original after specifying the original size and sending size, depending on these sizes, a margin is created at the bottom, left, or right side of paper. By using the centering, the image is placed with a margin equally created at each of the page Top/Bottom and Left/Right. Use the procedure below to center then image when sending a scanned image. 5-6 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Centering]. 4 Press [On]. Centering is performed. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. OPERATION GUIDE Sending Functions Mixed Sized Originals Using the optional document processor, the originals of different sizes can be placed in a batch and sent. In this operation, up to 30 originals of different sizes can be placed in the document processor at the same time. Originals of the Same Width When the original widths are the same, the combinations of originals that can be placed are as follows. • Ledger and Letter (A3 and A4) 5 Ledger • Letter Ledger Legal and Letter-R (Folio and A4-R) Legal • Letter Letter-R Letter-R l B4 and B5 OPERATION GUIDE 5-7 Sending Functions When the original widths are different The combinations of originals of different sizes that can be placed together are as follows. NOTE: When mixing the original sizes as using the following combination: Folio, A4-R, and B5-R, make sure to set the System Menu key -> Common Settings -> Original / Paper Settings -> Original Auto Detect to [On] for [Folio]. For more information, refer to Automatic Detection of Originals (Available for metric models only) on page 8-9. • A3, B4, A4, B5 • B4, A4-R, B5 • Folio, A4-R, B5-R 5-8 OPERATION GUIDE Sending Functions Use the procedure below to send mixed sized originals as a batch. 1 Press the Send key. 2 Place the original into the document processor. IMPORTANT: When you place originals of different width, place the top edge of originals to align with the width guide at the backside. If the originals are placed unevenly, they may not be scanned correctly. Ready to send. Destination 3 Press [Original/Sending Data Format] and then [Mixed Sized Originals]. 4 Select the combination of originals from [Same Width] and [Different Width]. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. 5 Mixed Size Originals Place original. Original Zoom Paper : --: 100% : --- Scan all sheets in the document processor, even if differently sized, then send. *Up to 30 sheets can be placed in the document processor for mixed size originals. Off Same Width Different Width Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 5-9 Sending Functions 1-sided/2-sided Selection Select the type and binding of original depending on the original. The table below lists the binding directions for each original type. Original Type Binding 1-sided Sheet Original 1-sided — 2-sided Sheet Original 2-sided* Binding Left/Right, Binding Top Open Book Original such as magazine and book Book Binding Left, Binding Right * Only when the optional document processor is used. Use the procedure below to select the original type and binding direction when sending scanned originals. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [2sided/Book Original]. 4 Press [1-sided], [2-sided], or [Book]. 5 When selecting [2-sided], select the binding direction and press [Original Orientation] to select the direction in which the original is set on the platen. When selecting [Book], select the binding direction. 6 Press [OK]. 7 Specify the destination, and press the Start key to start sending. Place original. 2-sided/Book Original 1-sided Place original. 2-sided Left Right Book Original : --- Zoom Paper : 100% : --- Top Edge Top Original Orientation Preview Add Shortcut Status 5-10 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Original Orientation To send the document in the orientation that can be read properly, specify the upper orientation of original. To use the functions below, select the orientation in which the original is set on the platen. • 2-sided/Book Original • Border Erase * If [On] is selected as the Orientation Confirmation (page 8-15) setting in the System Menu, the selection screen for original orientation appears when you select any of the above functions. When placing the original on the platen 5 Original [Top Edge Top] [Top Edge Left] When placing the original on the optional document processor Original [Top Edge Top] [Top Edge Left] Use the procedure below to select the orientation when placing the originals on the platen for sending. OPERATION GUIDE 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [Original Orientation]. 5-11 Sending Functions Ready to send. Destination 4 Select original orientation from [Top Edge Top] and [Top Edge Left]. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Original Orientation Select the orientation of the original document's top edge. Place original. Original : --- Zoom Paper : 100% : --- Top Edge Top Top Edge Left Preview Add Shortcut Cancel OK 08/08/2009 Status 10:10 File Format Select the file format of the image to send. The table below lists the file formats and their details. File Format Adjustable range of image quality Color mode PDF 1 Low Quality (High Comp.) to 5 High Quality (Low Comp.) Auto Color (Color/Grayscale), Auto Color (Color/Black and White), Full Color, Grayscale, Black and White TIFF 1 Low Quality (High Comp.) to 5 High Quality (Low Comp.) Auto Color (Color/Grayscale), Auto Color (Color/Black and White), Full Color, Grayscale, Black and White JPEG 1 Low Quality (High Comp.) to 5 High Quality (Low Comp.) Auto Color (Color/Grayscale), Full Color, Grayscale XPS 1 Low Quality (High Comp.) to 5 High Quality (Low Comp.) Auto Color (Color/Grayscale), Full Color, Grayscale High Comp. PDF 1 Compression Ratio Priority to 3 Quality Priority Auto Color (Color/Grayscale), Auto Color (Color/Black and White), Full Color, Grayscale NOTE: In the color mode, when auto color (color/black and white) is selected, [JPEG] and [XPS] cannot be specified, and when black and white is selected, [JPEG], [High Comp. PDF], and [XPS] cannot be specified. When [High Comp. PDF] is specified, you cannot adjust the image quality. In addition, when previewing the color of the image by selecting [High Comp. PDF], it may differ from the actual color. You can use PDF encryption functions. For details, refer to the following PDF Encryption Functions. 5-12 OPERATION GUIDE Sending Functions Use the procedure below to select the file format for transmission. Ready to send. 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [File Format]. 4 Select the file format from [PDF], [TIFF], [JPEG], [XPS], and [High Comp. PDF]. When the color mode in scanning has been selected for Grayscale or Full Color, set the image quality. Destination Place original. File Format Image Quality PDF Place original. TIFF Compression Ratio Priority Standard If you selected [PDF] or [High Comp. PDF], press [Encryption] and specify the encryption settings. Quality Priority JPEG Original : --- Zoom Paper : 100% : --Preview XPS 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Off Encryption High Comp. PDF Add Shortcut Cancel OK 08/08/2009 Status 10:10 File Separation Create several files by dividing scanned original data page by page, and send the files. Use the procedure below to split scanned original data into separate files when sending scanned originals. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format] and then [File Separation]. 4 Press [Each Page] to set File Separation. 5 Press [OK]. 6 Specify the destination, and press the Start key. The scanned original is sent after being divided into files of one page each. Place original. File Separation Create and send a file for each page of the original that was read. Place original. Original Zoom Paper : --: 100% : --- Off Each Page Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 NOTE: Three-digit serial number such as abc_001.pdf, abc_002.pdf... is attached to the end of the file name. 5-13 5 Sending Functions PDF Encryption Functions If you have selected PDF or High Comp. PDF for file format, you can restrict the access level for displaying, printing, and editing PDF's by assigning a secure password. The items you can restrict the access level with are as follows. Item Value Detail Compatibility Acrobat 4.0 or later, Acrobat 5.0 or later Select the version that is compatible with the PDF file. Password to Open Document Off, On Enter the password to open the PDF file Password to Edit/Print Document Off, On Enter the password to edit the PDF file When you have entered the password to edit/print document, you can specifically limit the operation. When you send a PDF file, use the procedure below to encrypt the PDF file for transmission. File Format - Encryption Compatibility 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Original/Sending Data Format], [File Format], [PDF] or [High Comp. PDF], and [Encryption]. 4 Press [ ] of Compatibility, select Acrobat 4.0 and later or Acrobat 5.0 and later. 5 When you enter the password to open the PDF file, select [On] of Password to Open Document. 6 Press [Password], enter a password (up to 256 characters) and then press [OK]. Acrobat 4.0 and later Encryption Level: Middle(40-bit) Password to Open Document Password to Edit/Print Document Off Password On Confirmation Off Password On Confirmation Detail Cancel Status NOTE: Refer to the Character Entry Method on page OK 08/08/2009 10:10 Appendix-10 for details on entering characters. 7 Press [Confirmation] and enter the password again for confirmation. Then press [OK]. 8 When you enter the password to edit the PDF file, select [On] of Password to Edit/Print Document. 9 In the same way as the entry of Password to Open Document, enter the password to change the PDF file. 10 Press [Detail]. 5-14 OPERATION GUIDE Sending Functions 11 Restrict the access level of the PDF file. Press [ ] of Printing Allowed to select the item (the scope of limit). The item to be displayed differs according to the version of Acrobat selected in Compatibility in step 4. File Format - Detail Printing Allowed Not Allowed Changes Allowed Not Allowed Copy ng of Text/Images/Others Disable Enable Cancel OK 08/08/2009 Status 10:10 The table below shows the available settings. Item 5 Detail Not Allowed Make the printing of PDF file impossible Allowed (Low Resolution only)* Can print the PDF file only in low resolution Allowed Can print the PDF file in original resolution * Only displayed when [Acrobat 5.0 and later] is selected in Compatibility. 12 Press [ ] of Changes Allowed, and select the item (the scope of limit). The item to be displayed differs according to the version of Acrobat selected in Compatibility in step 4. The table below shows the available settings. Item Detail Not Allowed Cannot change the PDF file Commenting Can only add commenting Inserting/Deleting/ Rotating Pages* Can only insert, delete, and rotate the pages of the PDF file Page Layout except extracting Pages** Can change the page layout except extracting the pages of the PDF file Any except extracting Pages Can conduct all operations except extracting the pages of the PDF file * ** Only displayed when [Acrobat 5.0 and later] is selected in Compatibility. Only displayed when [Acrobat 4.0 and later] is selected in Compatibility. 13 From Copying of Text/Images/Others, select [Disable] or [Enable]. OPERATION GUIDE 5-15 Sending Functions The table below shows the available settings. Item Detail Disable Prohibit the copying of text and objects on the PDF file. Enable Can copy text and objects on the PDF file. 14 Press [OK] three times to return to Original/ Sending Data Format. 15 Specify the destination, and press the Start key to start sending. Image Quality Select image quality suitable to the type of original. The table below shows the quality options. Item Detail Text+Photo Text and photos together. Photo For photos taken with a camera. Text Only text, no photos. for OCR For documents to be read by OCR.* * This function is only available for black and white mode. Use the procedure below to select the quality when sending scanned originals. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Original Image]. 4 Select the original image. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Original Image Select original image type for best results. [for OCR]: For documents to be read by OCR. Place original. Text+Photo Original : --- Zoom Paper : 100% : --- Photo Text for OCR Preview Add Shortcut Status 5-16 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Adjusting Density Use the procedure below to adjust the density when scanning the originals. The table below shows the available settings. Item Detail Manual Adjust density using 7 or 13 levels. Auto Optimum density is selected according to the density of the original. The procedure for adjusting the density is explained below. Ready to send. Destination 5 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Density]. 4 When selecting manual density adjustment, press [-3] to [+3] (Lighter - Darker) to adjust density. Place original. Density When selecting auto density adjustment, press [Auto]. Auto Place original. Lighter Normal -3 Original : --- Zoom Paper : 100% : --- -1 -2 -2.5 -1.5 Darker 0 -0.5 +1 +0.5 +2 +1.5 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. +3 +2.5 Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 5-17 Sending Functions Scan Resolution Select the fineness of scanning resolution. The finer the scanning becomes (the larger the number becomes), the better the image quality becomes. However, better resolution also results in larger file size (file capacity) and longer scanning and sending times. The selectable resolution is 200x100dpi Normal, 200x200dpi Fine, 200x400dpi Super Fine, 300x300dpi, 400x400dpi Ultra Fine, or 600x600dpi. The procedure for adjusting the scanning resolution when sending a scanned image is explained below. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Scan Resolution]. 4 Select the resolution. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Scan Resolution Select fineness of scanning resolution. The larger the number, the better the image resolution. Place original. Original Zoom Paper Preview Add Shortcut Status 5-18 600x600dpi 400x400dpi Ultra Fine 300x300dpi 200x400dpi Super Fine 200x200dpi Fine 200x100dpi Normal : --: 100% : --- Cancel OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Sharpness Select the sharpness of the image outline. The table below shows the available settings. Item Detail Sharpen Emphasize the image outline. Make letters and lines appear sharper. Unsharpen Blur the image outline. Can weaken a Moire effect (grids appearing as wavelike patterns when scanning printed photos). 5 Use the procedure below to set the sharpness when sending scanned images. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Sharpness]. 4 Press [-3] to [+3] (Unsharpen - Sharpen) to adjust the sharpness. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Sharpness Place original. Unsharpen -3 Original Zoom Paper Sharpen -2 -1 0 +1 +2 +3 : --: 100% : --Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 5-19 Sending Functions Background Density Adjustment Lightens the background of the colored original when it is too dark. NOTE: You cannot adjust the background density if you selected [Black & White] in Color / Grayscale / Black and White Selection (see page 5-21). Use the procedure below to set the background density when sending scanned images. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Background Density Adj.]. 4 Press [On], and press [1] to [5] (Lighter - Darker) to adjust the background density. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Background Density Adj. Off Background Lighter Place original. 1 Original Zoom Paper Darker On 2 3 4 5 : --: 100% : --Preview Add Shortcut Status 5-20 Cancel OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Color / Grayscale / Black and White Selection This feature allows you to select the color mode used for scanning when sending images. You can select from Auto (Color/Gray), Auto (Color/B & W), Full Color, Grayscale or Black & White. Use the procedure below to select the color mode when sending scanned images. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Color/Image Quality] and then [Color Selection]. 4 Select the color mode to be used for scanning. 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Place original. Color Selection Select scanning color. Select [Auto Color] to automatically send color originals in full color and black & white originals in black & white. Place original. Original Zoom Paper Auto Color (Color/Gray) Auto Color (Color/B & W) Full Color Grayscale : --: 100% : --Black & White Preview Add Shortcut Status OPERATION GUIDE Cancel OK 08/08/2009 10:10 5-21 5 Sending Functions Continuous Scan When the multi-page originals cannot be placed in the document processor at one time, the originals can be scanned in separate batches and then sent as one job. With this function, originals can be scanned one after another until you press [Scan Finish]. Any of the following settings can be changed during scanning. • Original Size selection • Original Orientation • 1-sided / 2-sided selection • Scan density • Image quality • Scan resolution • Color selection • Sending Size selection • Zoom • Border Erase The procedure for using continuous scanning when sending scanned images is explained below. Ready to send. Destination 1 Press the Send key. 2 Press [Advanced Setup] and then [Continuous Scan]. 3 Press [On]. Continuous Scan is selected. 4 Press [OK]. 5 Specify the destination. 6 Place the original, and press the Start key. Place original. Continuous Scan Place original. Original Zoom Paper : --: 100% : --- Scan a large number of originals in separate batches and then produce as one job. *Settings can be changed during scanning. Off On Preview Add Shortcut Status Cancel OK 08/08/2009 10:10 When the scanning is completed, change the settings as necessary. 7 Place the next original, and press the Start key. Scan the remaining originals by the same procedure. When you have scanned all the originals, press [Finish Scan] to start sending. 5-22 OPERATION GUIDE Sending Functions Border Erase Use Border Erase to remove black shadows that appear around the outside of the original when scanning and sending originals. The following options can be selected. Border Erase Sheet Erases black borders around the single sheet original. Original 5 Copy Border Erase Book Erases black borders around the edges and in the middle of the original such as a thick book. You can specify the widths individually to erase the borders around the edges and in the center of the book. Original Copy Individual Border Erase Specify border erase widths individually for all edges. Original Copy In each option, the available ranges are as below. Input units Border Erase Range Inch models 0 to 2" (in 0.01" increments) Metric models 0 mm to 50 mm (in 1-mm increments) OPERATION GUIDE 5-23 Sending Functions Border Erase to Back Page When scanning a 2-sided original, this allows you to erase the borders on the back of the original. The table below shows the available settings. Item Detail Same as Front Page Border Erase performed using the same setting as the front page Do Not Erase No Border Erase performed on the back page Use the procedure below to erase borders when sending scanned originals. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Border Erase]. 4 Press [Border Erase Sheet] to erase borders for an individual sheet or [Border Erase Book] to erase borders for a book. Place original. Border Erase Border Off (0.00 - 2.00) 0.25 Use [+] or [-] to enter the width in Border or Gutter. Press [# Keys] to use the number keys for entry. Border Erase Sheet Place original. Border Erase Book Original Zoom Paper " # Keys Gutter Back Page (0.00 - 2.00) 0.25 Individual Border Erase : --: 100% : --- Same as Front Page Press [Individual Border Erase] to select the individual border erase. " # Keys Preview Add Shortcut Cancel Use [+] or [-] to enter the border width or press [# Keys] and enter the width using the numeric keys. OK Status 08/08/2009 Ready to send. 10:10 Press [Original Orientation] to select the original orientation from either [Top Edge Top] or [Top Edge Left], and press [OK]. Destination Place original. Border Erase (0.00 - 2.00) Off Place original. Original Zoom Paper : --: 100% : --Preview Add Shortcut Status 5-24 Border Erase Sheet Top 0.25 Bottom 0.25 Border Erase Book Left 0.25 Individual Border Erase Right 0.25 " For 2-sided originals, press [Back Page] and then press [Same as Front Page] or [Do Not Erase]. " " Same as Front Page Back Page " 5 Press [OK]. 6 Specify the destination, and press the Start key to start sending. Top Edge Top # Keys Cancel Original Orientation OK 08/08/2009 10:10 OPERATION GUIDE Sending Functions Enter Document Name/File Name This setting allows you to assign a document name to scanned images. You can specify a default for the document name. Use the procedure below to assign names to scanned documents that you are sending. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [File Name Entry]. 4 Press [File Name]. 5 Enter the document name, and press [OK]. 5 Place original. File Name Entry Add a file name. Additional information such as Job No. and Date and Time can also be set. File Name Additional Info doc & [ Date and Time Job No. Add Shortcut Status ] Date and Time Cancel OK 08/08/2009 10:10 NOTE: Up to 32 characters can be entered for the document name. OPERATION GUIDE 6 Press [Job No.] to enter the job No., and [Date and Time] to enter the date and time. 7 Press [OK]. 8 Specify the destination, and press the Start key to start sending. 5-25 Sending Functions Enter E-mail Subject and Body When sending E-mail, enter the subject and body of the E-mail. Use the procedure below to enter the subject and body for an E-mail message and then send the E-mail. Ready to send. Destination 1 Press the Send key. 2 Press [Advanced Setup] and then [E-mail Subject/ Body]. 3 Press [Subject]. 4 Enter the subject, and press [OK]. Place original. E-mail Subject/Body Subject Place original. Original Zoom Paper Body : --: 100% : --Preview Add Shortcut Status Cancel OK 08/08/2009 10:10 NOTE: Up to 60 characters can be entered for the subject. 5 Press [Body]. 6 Enter the body and press [OK]. NOTE: Up to 500 characters can be entered for the body. 5-26 7 Press [OK]. 8 Specify the destination, and press the Start key to start sending. OPERATION GUIDE Sending Functions WSD Scan WSD Scan saves images of originals scanned on this machine as files on a WSD-compatible computer. NOTE: To use WSD Scan, confirm that the computer used for WSD scanning and the machine is networkconnected, and WSD Scan Setup (page 8-68) is set to On in the network settings. For information on operating the computer, refer to the computer’s help or the operation guide of your software. Installing Driver Software (for Windows Vista) 1 Click Start and then Network in the computer. 2 Right-click the machine’s icon (UTAX: CD XXX:XXX) and then click Install. 5 NOTE: If the User Account Control window appears, click Continue. If the Found New Hardware window appears, click Cancel. 3 During the installation, double-click the icon shown on the task bar to display the Driver Software Installation screen. When Your devices are ready to use is displayed on the Driver Software Installation screen, the installation is completed. 1 Press the Send Key. Procedure Using this machine Displays the screen for sending. NOTE: Depending on the settings, the address book screen may appear. In this event, press [Cancel] to display the screen for sending. OPERATION GUIDE 2 Place the originals in the document processor or on the platen. 3 Press [WSD Scan]. 4 Press [From Operation Panel] and press [Next]. 5-27 Sending Functions 5 WSD Scan - Selecting Computer Select the destination computer and press [OK]. Select the destination computer and press [OK]. Press [Reload] to reload the computer list. Computer Name Reload You can view information on the selected computer by pressing [Detail]. pc00010 pc000102 pc000103 1/1 Detail pc000104 pc000105 Cancel Status Back OK 08/08/2009 10:10 6 Select the type of originals, file format, etc., as necessary. 7 Press the Start key. Sending begins and the software installed on the computer is activated. 1 Press the Send Key. Procedure Using WSD Scan from Your Computer The send screen appears. NOTE: Depending on the settings, the address book screen may appear. In this event, press [Cancel] to display the screen for sending. 5-28 2 Place the originals in the document processor or on the platen. 3 Press [WSD Scan]. 4 Press [From Computer] and press [Execute]. 5 Use the software installed on the computer to send the images. OPERATION GUIDE Sending Functions Job Finish Notice Sends a notice by e-mail when a job is completed. Use the procedure below to specify the Job Finish Notice settings. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Job Finish Notice]. 4 To select the destination from the address book, press [Address Book] on the left of the screen and then press [Address Book] in the next screen. Place original. Job Finish Notice Off Destination Address Book Select the destination to be notified, then press [OK]. Detail Address Entry Detail Add Shortcut You can view information on the notification destination by pressing [Detail]. Address Book Cancel OK 08/08/2009 Status 10:10 5 Specify the destination to send the finish notice, and press [OK]. NOTE: For the procedure to select the destination from the Address Book, refer Specifying Destination on page 3-30. Ready to send. Destination 6 To directly enter the address, press [Address Entry] and then [E-mail Address]. 7 Enter the E-mail address, and press [OK]. 8 Press [OK]. 9 Specify the destination, and press the Start key to start sending. Place original. Job Finish Notice Off Address Book E-mail Address Address Entry Add Shortcut Status Cancel OK 08/08/2009 10:10 When the sending is completed, the finish notice is sent to the specified E-mail address. OPERATION GUIDE 5-29 5 Sending Functions Send and Print When you send originals, this feature allows you to print a copy of the document being sent. The procedure for using Send and Print is explained below. 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup] and then [Send and Print]. 4 Press [On]. 5 Press [OK]. 6 Specify the destination and press the Start key. Transmission begins and a copy of the transmitted document is printed. Send and Store When you send originals, this feature allows you to store a copy of the document being sent in a Custom Box. The procedure for using Send and Store is explained below. Ready to send. Destination 1 Press the Send key. 2 Place the originals on the platen. 3 Press [Advanced Setup], [ Store]. 4 Press [On]. 5 Select the Custom Box in which the copy is to be stored. ], and then [Send and Place original. Send and Store Custom Box Off No Name Used Area On Add Shortcut Status 5-30 0006 06 BOX001 6% 0007 07 BOX002 4% 0008 08 BOX003 8% 0009 09 BOX004 4% 0010 10 BOX005 2% Cancel If a password entry screen for the Custom Box appears, enter the password. 2/2 You can view information on the selected Custom Box by pressing [Detail]. Detail OK 08/08/2009 10:10 6 Press [OK]. 7 Specify the destination and press the Start key. Transmission begins and a copy of the transmitted document is stored in the specified Custom Box. OPERATION GUIDE Sending Functions FTP Encrypted TX This allows you to encrypt documents when you send them. If you select [On] in this option, you can then select the encryption method in the basic send screen. Use the procedure below to scan and send originals as encrypted files. 1 Press the Send Key. 2 Place the originals in the document processor or on the platen. 3 Press [Advanced Setup], [ Encrypted TX]. 4 Press [On]. 5 Press [OK]. ], and then [FTP 5 NOTE: Click Advanced -> Secure Protocols in the Embedded Web Server. Be sure that SSL of Secure Protocol Settings is On and one or more effective encryption are selected in Clientside Settings. For details, refer to the Embedded Web Server Operation Guide. Color Type This sets the color type when you send color documents. The table below shows the available settings. Item Detail RGB – sRGB Match the color reproduction space between sRGB compatible systems. Selecting RGB displays the color profile values set on the machine. Send - Color Type Spec fy the color type to send color images. RGB 1 Press System Menu key. 2 Press [Send] and [Change] of Color Type. 3 Select [RGB] or [sRGB]. 4 Press [OK]. Profile: RGB FINE 1 sRGB Cancel Status OPERATION GUIDE OK 08/08/2009 10:10 5-31 Sending Functions About Color Profiles The color scanner provides color profiles to adjust color. NOTE: The color profile data import method varies for every TWAIN/WIA-compliant software. Use the color profile after carefully reading the manual included with your TWAIN/WIA-complaint software. Selecting a color profile compatible with this device 1 Select the color profile found in the CD included with this scanner CD (Product Library) under the Color Profile folder. NOTE: Use the indicated color profiles when you chose RGB in color type. 5-32 OPERATION GUIDE 6 Document Box This chapter explains the typical procedure for utilizing Document Box. • • • • Using a Custom Box ...........................................................................6-2 Using a Job Box................................................................................6-12 Printing Documents Stored in Removable USB Memory..................6-20 Saving Documents to USB Memory (Scan to USB) .........................6-22 OPERATION GUIDE 6-1 Document Box Using a Custom Box NOTE: In the following explanation, it is assumed that user login administration is enabled. For details on User Logon privileges, refer to User Privileges on page 3-40. Creating a New Custom Box Use the procedure below to create a new box in the user box. Custom Box. No. 0001 Name Owner SALES 1 Press the Document Box key. 2 Press [Custom Box] and then [Register/Edit Box]. 3 Press [Add]. 4 Press [Change] for each item, enter the information and then press [OK]. Used Area Anonymous ---- Search(Name) Search(No.) 1/1 Store File Custom Box Job Box Detail Removable Memory Status Register/Edit Box Open FAX Box 08/08/2009 10:10 The table below lists the items to be set. Item 6-2 Detail Box No Enter the box number by pressing [-, +] or number keys. The box number can be from 0001 to 1000. A Custom Box should have a unique number. If you enter 0000, the smallest number available will be automatically assigned. Box Name Enter a box name consisting of up to 32 characters. Refer to the Character Entry Method on Appendix-10 for details on entering characters. Box Password User access to the box can be restricted by specifying a password to protect the box. Entering a password is not mandatory. Enter the same password of up to 16 characters in both [Password] and [Confirm Password]. OPERATION GUIDE Document Box Item Detail Usage Restriction To preserve the hard disk capacity, the storage capacity for a box can be restricted. To enable a capacity restriction enter a value for the storage capacity of the Custom Box in megabytes by pressing [-, +] or number keys. You can enter a limit between 1 and 30,000. (Changes according to the number of created custom boxes.) Auto File Deletion Automatically deletes stored documents after a set period of time. Press [On] to enable automatic deletion and then use [+] and [-] or the numeric keys to enter the number of days for which documents are stored. You can enter any number between 1 and 31 day(s). To disable automatic file deletion, press [Off]. Overwrite Setting Specifies whether or not old stored documents are overwritten when new documents are stored. To overwrite old documents, press [Permit]. To retain old documents, press [Prohibit]. Delete after Printed Automatically delete document from the box once printing is complete. To delete the document, press [On]. To retain the document, press [Off]. 6 NOTE: If user login administration is enabled, "Owner" and "Permission" are also displayed. Refer to Creating new Custom Boxes when user login administration is enabled on page 3-41. 5 Check the details you have entered and then press [Register]. The Custom Box is created. Setting the document deletion time Sets the time when documents stored in a custom box are deleted. The procedure for using Auto File Deletion Time is explained below. OPERATION GUIDE 1 Press the System Menu key. 2 Press [Document Box/Removable Memory], [Next] of Custom Box, [Next] of Default Setting and then [Change] of Auto File Deletion Time. 6-3 Document Box Document Box/Removable Memory - Auto File Deletion Time 3 Set the time at which the document is deleted by pressing [+], [-]. Press [# Keys] to enter the time directly using the numeric keys. 4 Press [OK]. The time for document deletion is set. Set the time to automatically delete stored documents. Minute Hour 21 30 # Keys # Keys Cancel OK Status 08/08/2009 10:10 Storing Documents The procedure for storing documents in a custom box is explained below. Custom Box. No. 0001 Name Owner SALES ---- Search(Name) 1/1 Store File Status Job Box Press the Document Box key. 2 Place the originals in the document processor or on the platen. 3 Press [Custom Box], select the box where the document will be stored and then press [Store File]. Used Area Anonymous Search(No.) Custom Box 1 etail Removable Memory Register/Edit Box NOTE: The Custom Box to store a file needs to be created in advance. If a custom box is protected by a password, enter the correct password. Open FAX Box 08/08/2009 10:10 4 Select the type of originals, scanning density, etc., as necessary. 5 Press the Start key. The original is scanned and the data is stored in the specified Custom Box. NOTE: Enter up to 64 characters as the file name. 6-4 OPERATION GUIDE Document Box Printing Documents The procedure for printing documents in a custom box is explained below. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the document you want to print and press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 000 File Name 0404200710574501 10/10/2008 09:40 21 MB 000 0404200710574511 10/10/2008 09:50 21 MB 000 0404200710574521 10/10/2008 10:00 21 MB Select the document you wish to print by checking the checkbox. The document is marked with a checkmark. Search(Name) 6 NOTE: To deselect, press the checkbox again and 1/1 remove the checkmark. Detail Preview Print Send Join Move/Copy Delete Store File 4 Press [Print]. 5 Set the paper selection, duplex printing, etc., as desired. 6 Press the Start key. Printing of the selected document begins. Close Status OPERATION GUIDE 08/08/2009 10:10 6-5 Document Box Sending Documents The procedure for sending documents in a custom box is explained below. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the document you want to send and press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 00 File Name 0404200710574501 10/10/2008 09:40 21 MB 0002 0404200710574511 10/10/2008 09:50 21 MB 0003 0404200710574521 10/10/2008 10:00 21 MB NOTE: You cannot select and send multiple documents. To deselect, press the checkbox again and remove the checkmark. Detail Preview Send Join Move/Copy Delete Store File 4 Close Status The document is marked with a checkmark. Search(Name) 1/1 Print Select the document you wish to send by checking the checkbox. 08/08/2009 Press [Send]. 10:10 The screen for sending appears. NOTE: Depending on the settings, the address book screen may appear. 5 Set the destination. NOTE: For more information on selecting destinations, refer to Specifying Destination on page 3-30. 6 6-6 Press the Start key. Sending of the selected document begins. OPERATION GUIDE Document Box Form Overlay from Custom Boxes This function allows you to retrieve images (image files), overlay them into documents stored in custom boxes and then print the results. Use the procedure below. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the document you want to overlay the image into and print, and then press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 00 File Name 0404200710574501 10/10/2008 09:40 21 MB 00 0404200710574511 10/10/2008 09:50 21 MB 00 0404200710574521 10/10/2008 10:00 21 MB Select the document you wish to print by checking the checkbox. The document is marked with a checkmark. Search(Name) NOTE: To deselect, press the checkbox again and 1/1 remove the checkmark. Detail Preview Print Send Join Move/Copy Delete Store File 4 Press [Print]. 5 Press [Functions], [Form Overlay], [Select Stored Form], and then [Select Form]. Close 08/08/2009 Status 10:10 Copies Ready to store in Box. File Name: Form Overlay Off Density (10 - 100) 100 Place original. Original : --- Zoom Paper : 100% : --- % NOTE: You can change the form density setting through 10 levels from 10% to 100%. Press the [+] or [-] buttons in Density. Select Stored Form Off Select Form Preview Add Shortcut Status Cancel OK 08/08/2009 10:10 6 In Form Overlay - Select Form, select the image file to be overlaid onto the document from the displayed document boxes. You can only select one image file. OPERATION GUIDE 7 Press [OK]. 8 Press [OK] again to return to the Functions screen. 9 Press the Start key. Printing begins. 6-7 6 Document Box Editing Documents This function allows you to move or copy documents stored in custom boxes into other boxes or to join multiple documents together. You can also copy documents to USB memory connected to this machine. Moving a Document / Copying a Document The procedure for moving or copying documents is explained below. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the document you want to move or copy and press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 00 File Name 0404200710574501 10/10/2008 09:40 21 MB 00 0404200710574511 10/10/2008 09:50 21 MB 00 0404200710574521 10/10/2008 10:00 21 MB Select the document in the list that you want to move or copy by pressing the checkbox. The document is marked with a checkmark. Search(Name) NOTE: To deselect, press the checkbox again and 1/1 remove the checkmark. Detail Preview Print Send Join Move/Copy Delete Store File 4 Press [Move/Copy]. 5 To move the document, press [Move to Custom Box]. Close 08/08/2009 Status 10:10 Custom Box. Move/Copy To copy the document, press [Copy to Custom Box] or [Copy to Removable Mem.]. Select the required operation and press [Next]. 6 Copy to Custom Box Move to Custom Box Cancel Status 6-8 Press [Next]. Copy to Removable Mem. Back Next 08/08/2009 10:10 OPERATION GUIDE Document Box 7 Job Box. To copy or move the document to a custom box, select the destination box. Move to Custom Box To copy the document to USB memory, select the destination folder and press [Next]. If necessary, set the saved file size and the file format, etc. Select the destination box and press [Move]. Document No. Name Owner Used Area 0001 Document1 Administrator 2 MB 0002 Document2 Administrator 3 MB 0003 Document3 Administrator 3 MB 0004 Document4 Administrator 5 MB Cancel Back Up 8 Open Press [Move] or [Copy] and then press [Yes] in the confirmation screen. The selected document is moved or copied. Move Status 08/08/2009 10:10 NOTE: If the box to which the document is to be moved or copied is protected by a password, enter the correct password. Joining Documents 6 The procedure for joining documents in a custom box is explained below. NOTE: You can only join a document to other documents in the same custom box. If necessary, move the documents to be joined beforehand. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the documents you want to join and press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 00 File Name 0404200710574501 10/10/2008 09:40 21 MB 00 0404200710574511 10/10/2008 09:50 21 MB 00 0404200710574521 10/10/2008 10:00 21 MB Select the documents in the list that you wish to join by pressing the checkbox. The document is marked with a checkmark. Search(Name) You can join up to 10 documents. 1/1 Detail Print Send Join Move/Copy Delete Preview NOTE: To deselect, press the checkbox again and Store File remove the checkmark. Close Status OPERATION GUIDE 08/08/2009 10:10 4 Press [Join]. 6-9 Document Box 5 Join Confirm the order of documents to combine. File Name Date and Time Highlight the document you want to rearrange and press [Up] or [Down] to move it to the correct place in the sequence. Size 2008101010574501 10/10/2008 09:40 21 MB 2008101010574511 10/10/2008 09:50 21 MB 2008101010574521 10/10/2008 10:10 21 MB Arrange the documents into the order in which they are to be joined. 1/1 Up 6 Press [Next]. 7 Press [File Name], enter the file name for the joined document and press [OK]. Down Cancel Status Next 08/08/2009 10:10 NOTE: Enter up to 32 characters as the file name. 8 Press [Join] and then press [Yes] in the confirmation screen. The documents are joined. NOTE: After joining, the original documents are left unchanged. Delete the documents if they are no longer needed. 6-10 OPERATION GUIDE Document Box Deleting Documents The procedure for deleting documents in a custom box is explained below. 1 Press the Document Box key. 2 Press [Custom Box], select the box containing the document you want to delete and press [Open]. NOTE: If a custom box is protected by a password, enter the correct password. 3 Box: Date and Time Size 0001 File Name 0404200710574501 10/10/2008 09:40 21 MB 0002 0404200710574511 10/10/2008 09:50 21 MB 0003 0404200710574521 10/10/2008 10:00 21 MB Preview Join Move/Copy Delete 6 NOTE: [Delete] is disabled until a document is selected. To deselect, press the checkbox again and remove the checkmark. Detail Send The document is marked with a checkmark. Search(Name) 1/1 Print Select the document you wish to delete by checking the checkbox. Store File Close Status OPERATION GUIDE 08/08/2009 10:10 4 Press [Delete]. The delete confirmation screen appears. 5 Press [Yes]. The document is deleted. 6-11 Document Box Using a Job Box Private Print/Stored Job Box Private Print/Stored Job Box stores the print data which is printed by using the printer driver as a Private Print/ Stored Job. Refer to the Printer Driver User Guide on how to print a job as Private Print or Stored Job using the printer driver. Printing a Document in Private Print/Stored Job Box You can print documents stored in a Private Print/Stored Job box. Use the procedure below to print a document. Job Box. 1 Press the Document Box key. 2 Press [Job Box]. 3 Select [Private Print/Stored Job] and press [Open]. 4 Select the creator of the document to print and press [Open]. 5 Select the document and press [Print]. Private Print/Stored Job User Name Files 1 User 5 2 User 2 3 User 1 4 User 1 5 User 1 1/2 Open Close Status 08/08/2009 10:10 Job Box. User: Date and Time Size 1File 10/10/2008 09:40 21 MB 2File 10/10/2008 09:45 30 MB 3File 10/10/2008 09:50 36 MB 4File 10/10/2008 09:55 21 MB 5File 10/10/2008 10:00 30 MB F le Name Print NOTE: If a password is set for the Custom Box in advance, enter the correct password. 1/1 Detail Delete Close Status 08/08/2009 10:10 6 If the document is protected by a password, enter the password using the numeric keys. 7 Specify the number of copies to print as desired. 8 Press [Start Print] to start printing. Upon completion of printing, the Private Print job is automatically deleted. 6-12 OPERATION GUIDE Document Box Deleting a Document You can delete documents stored in a Private Print/Stored Job box. Use the procedure below to delete a document. Job Box. 1 Press the Document Box key. 2 Press [Job Box]. 3 Select [Private Print/Stored Job] and press [Open]. 4 Select the creator of the document and press [Open]. Private Print/Stored Job User Name Files 1 User 5 2 User 2 3 User 1 4 User 1 5 User 1 6 1/2 Open Close Status 08/08/2009 10:10 5 Job Box. To delete the document, select the document and press [Delete]. User: F l Nam Dat a d T m 10/10/2008 09:40 21 MB 2File 10/10/2008 09:45 30 MB 3File 10/10/2008 09:50 36 MB 4File 10/10/2008 09:55 21 MB 5File 10/10/2008 10:00 30 MB Print When the delete confirmation screen appears, press [Yes]. Sz 1File If the document is protected by a password, enter the password using the numeric keys and the document is deleted. 1/1 Detail Delete Close Status 08/08/2009 10:10 Quick Copy/Proof and Hold Print Box Quick Copy/Proof and Hold box stores the print data which is printed by using the printer driver as a Quick Copy or Proof and Hold Print job. Refer to the Printer Driver User Guide on how to print a job as Quick Copy or Proof and Hold Print job using the printer driver. Setting the Number of Stored Jobs To maintain free space on the hard disk, you can set the maximum number of stored jobs. Use the procedure below to set the number of stored jobs. OPERATION GUIDE 1 Press the System Menu key. 2 Press [Document Box/Removable Memory], [Next] of Job Box, then [Change] of Quick Copy Job Retention. 6-13 Document Box 3 Document Box/Removable Memory - Quick Copy Job Retention Set the maximum number of quick copy/proof print jobs to retain. Use [-]/[+] or the numeric keys to enter a number. *Set this number to 0 to not retain any jobs. You can also enter the number using the numeric keys. (0 - 50) 32 Press [+] or [–] to enter the maximum number of stored jobs. You can enter any number between 0 and 50. job(s) NOTE: If you enter a value of 0 (zero), you cannot use the Repeat Copy function. Cancel OK 08/08/2009 Status 10:10 4 Press [OK]. The maximum number of stored jobs is set. Printing a Document You can print documents stored in the Quick Copy/Proof and Hold box. Use the procedure below to print a document. Job Box. 1 Press the Document Box key. 2 Press [Job Box]. 3 Select [Quick Copy/Proof and Hold] and press [Open]. 4 Select the creator of the document and press [Open]. 5 Select the document to print, and press [Print]. 6 Specify the number of prints as desired. 7 Press [Start Print] to start printing. Quick Copy/Proof and Hold User Name Files 1 User 5 2 User 2 3 User 1 4 User 1 5 User 1 1/2 Open Close 08/08/2009 Status 10:10 Job Box. User: Date and Time Size 1File 10/10/2008 09:40 21 MB 2File 10/10/2008 09:45 30 MB 3File 10/10/2008 09:50 36 MB 4File 10/10/2008 09:55 21 MB 5File 10/10/2008 10:00 30 MB F le Name Print 1/1 Detail Delete Close Status 6-14 08/08/2009 10:10 OPERATION GUIDE Document Box Deleting a Document You can delete documents stored in the Quick Copy/Proof and Hold box. Use the procedure below to delete a document. Job Box. 1 Press the Document Box key. 2 Press [Job Box], [Quick Copy/Proof and Hold], then [Open]. 3 Select the creator of the document and press [Open]. Quick Copy/Proof and Hold User Name Files 1 User 5 2 User 2 3 User 1 4 User 1 5 User 1 1/2 6 Open Close 08/08/2009 Status 10:10 4 Job Box. Select the document to delete and press [Delete]. The delete confirmation screen appears. User: Date and Time Size 1File 10/10/2008 09:40 21 MB 2File 10/10/2008 09:45 30 MB 3File 10/10/2008 09:50 36 MB 4File 10/10/2008 09:55 21 MB 5File 10/10/2008 10:00 30 MB F le Name Print 1/1 Detail Delete Close Status 08/08/2009 10:10 5 Press [Yes]. The document is deleted. Repeat Copy Box Setting the Number of Stored Jobs To maintain free space on the hard disk, you can set the maximum number of stored jobs. Use the procedure below to specify the maximum number of stored jobs. OPERATION GUIDE 1 Press the System Menu key. 2 Press [Document Box/Removable Memory], [Next] of Job Box, [Change] of Repeat Copy Job Retention. 6-15 Document Box 3 Document Box/Removable Memory - Repeat Copy Job Retention Set the maximum number of repeat copy jobs to retain. Use [-]/[+] or the numeric keys to enter a number. *Set this number to 0 to not retain any jobs. Use the [+] and [–] keys or the numeric keys to enter the maximum number of stored jobs. You can enter any number between 0 and 50. (0 - 50) 32 NOTE: If you enter a value of 0 (zero), no jobs are job(s) stored. 4 Cancel OK 08/08/2009 Status Press [OK]. The maximum number of stored jobs is set. 10:10 Printing a Document You can print the documents stored in the Repeat Copy box. Use the procedure below to print a document. Job Box. 1 Press the Document Box key. 2 Press [Job Box]. 3 Select [Repeat Copy] box, and press [Open]. 4 Select the document to print and press [Print]. 5 If the document is protected by a password, enter the password using the numeric keys. 6 Press [Start Print] to start printing. Repeat Copy S 1010200800101002 10/10/2008 10:00 21 MB 1/1 Detail Print Delete Close Status 08/08/2009 10:10 The Repeat Copy box job will be deleted when the main power switch is turned off. 6-16 OPERATION GUIDE Document Box Automatic Delete Setting for Temporary Documents This setting specifies that documents, such as Private Printing, Quick Copying, or Proof and Hold Printing, saved temporarily in the job box are automatically deleted after they have been saved for a set time. The table below shows the available settings. Item Detail Off Temporary documents are not automatically deleted. However, the temporary documents will be deleted when the power is turned off. 1 hour Documents are deleted after 1 hour. 4 hours Documents are deleted after 4 hours. 1 day Documents are deleted after 1 day. 1 week Documents are deleted after 1 week. 6 Use the procedure below to set automatic deletion for temporary documents. 1 Press the System Menu key. 2 Press [Document Box/Removable Memory], [Next] of Job Box, then [Change] of Deletion of Job Retention. 3 Select the time for automatic deletion. To deactivate automatic deletion, press [Off]. 4 Press [OK]. NOTE: This function is valid for documents saved after the function is set. Regardless of this function setting, temporary documents are deleted when the main power switch is turned off. Form for Form Overlay Box Storing a Form You can store forms to be used for the form overlay in the Form for Form Overlay box. You can store a 1-page form. Use the procedure below to store a form. OPERATION GUIDE 1 Press the Document Box key. 2 Place the original in the document processor or on the platen. 3 Press [Job Box]. 6-17 Document Box Job Box. 4 Select [Form for Form Overlay] and press [Open]. 5 Press [Store File]. 6 If necessary, select the image quality of original, scanning density, etc. before the original is scanned. 7 Press the Start key. The original is scanned and stored in the Form for Form Overlay box. Files Name Private Print/Stored Job 21 Quick Copy/Proof and Hold 21 Repeat Copy 21 Form for Form Overlay 21 Open Custom Box Job Box Removable Memory FAX Box Status 08/08/2009 10:10 Form for Form Overlay Name 1010200809530900 Date and Time 10/10/2008 09:00 Size 21 MB 1010200800530910 10/10/2008 09:10 30 MB 1010200800530920 10/10/2008 09:20 30 MB 1/1 Detail Print Delete Store File Close Status 08/08/2009 10:10 NOTE: For information on using image overlays with a stored form, see Form Overlay on page 4-22 and Form Overlay from Custom Boxes on page 6-7. Deleting a Form Stored You can delete the form stored in the Form for Form Overlay box. Use the procedure below to delete a form. 6-18 1 Press the Document Box key. 2 Press [Job Box]. 3 Select [Form for Form Overlay] and press [Open]. OPERATION GUIDE Document Box 4 Form for Form Overlay Name Date and Time 1010200809530900 10/10/2008 09:00 Select the form to delete and press [Delete]. The delete confirmation screen appears. Size 21 MB 1010200800530910 10/10/2008 09:10 30 MB 1010200800530920 10/10/2008 09:20 30 MB 1/1 Detail Print Delete Store File Close Status 08/08/2009 10:10 5 Press [Yes]. The form is deleted. 6 OPERATION GUIDE 6-19 Document Box Printing Documents Stored in Removable USB Memory Plugging USB memory directly into the machine enables you to quickly and easily print the files stored in the USB memory without having to use a computer. Limitations • The following file types can be printed: •PDF file (Version 1.5) •TIFF file (TIFF V6/TTN2 format) •JPEG file •XPS file •Encrypted PDF file • PDF files you wish to print should have an extension (.pdf). • Files to be printed should be saved no further down than the top 3 folder levels. • Use USB memory properly formatted by this machine. • Plug the USB memory directly into the USB memory slot (A1). We do not guarantee that USB memory printing is error free if a USB hub is used. Printing Print documents stored in the removable USB memory. 1 Plug the USB memory into the USB memory slot (A1). IMPORTANT: Use USB memory formatted by this machine. If a USB memory formatted by any other device is used, The removable memory is not formatted. may appear. To format a USB memory, press [Format] and follow the instructions on the screen. 2 When the machine reads the USB memory, Removable Memory is recognized. Displaying files. may appear. Press [Yes] to display the removable memory screen. NOTE: If the message does not appear, press the Document Box key and then [Removable Memory]. 3 Select the folder containing the file to be printed and press [Open]. The machine will display documents in the top 3 folder levels, including the root folder. NOTE: To return to a higher level folder, press [Up]. 6-20 OPERATION GUIDE Document Box Removable Memory. 4 Select the file to be printed and press [Print]. 5 Change the number of copies, duplex printing, etc. as desired. 6 Press the Start key. Printing of the selected file begins. Removable Memory Name Date and Time Size 1 Document 10/10/2008 09:30 1 MB 2 Document 10/10/2008 09:40 3 MB 3 Document 10/10/2008 09:50 4 MB 4 Document 10/10/2008 10:00 1 MB Memory Information 5 Document 10/10/2008 10:05 2 MB Remove Memory Up Delete Print Custom Box Job Box Detail Removable Memory 001/999 Open Store File FAX Box 08/08/2009 Status 10:10 Removing USB Memory Remove the USB memory. IMPORTANT: Be sure to follow the proper procedure to avoid damaging the data or USB memory. Removable Memory. 1 Press the Document Box key. 2 Press [Removable Memory]. 3 Press [Remove Memory]. 4 Remove the USB memory after Removable Memory can be safely removed. is displayed. Removable Memory Name Date and Time Size 1 Document 10/10/2008 09:30 1 MB 2 Document 10/10/2008 09:40 3 MB 3 Document 10/10/2008 09:50 4 MB 4 Document 10/10/2008 10:00 1 MB Memory Information 10/10/2008 10:05 2 MB Remove Memory Up 5 Document Delete Print Custom Box Job Box Detail Removable Memory Status OPERATION GUIDE Open 001/999 Store File FAX Box 08/08/2009 10:10 6-21 6 Document Box Saving Documents to USB Memory (Scan to USB) This function allows you to store scanned image files in USB memory connected to the machine. You can store files in PDF, TIFF, JPEG, XPS or high-compression PDF format. NOTE: The maximum number of the storable files is 100. Storing Documents The procedure for storing documents in removable USB memory is explained below. 1 Plug the USB memory into the USB memory slot (A1). IMPORTANT: Use only USB memory that has been formatted on this machine. If USB memory formatted on another device is used, The removable memory is not formatted message may appear. To format the USB memory, press [Format]. 2 When the machine reads the USB memory, Removable Memory is recognized. Displaying files. may appear. Press [Yes] to display the removable memory screen. NOTE: If the message does not appear, press the Document Box key and then [Removable Memory]. 3 Select the folder where the file will be stored and press [Open]. The machine will display the top 3 folder levels, including the root folder. Removable Memory. 4 Press [Store File]. 5 Set the type of original, file format, etc., as desired. 6 Press the Start key. The original is scanned and the data is stored in the USB memory. Removable Memory Name Date and Time Size 1 Document 10/10/2008 09:30 1 MB 2 Document 10/10/2008 09:40 3 MB 3 Document 10/10/2008 09:50 4 MB 4 Document 10/10/2008 10:00 1 MB Memory Information 2 MB Remove Memory Up 5 Document 10/10/2008 10:05 Delete Print Custom Box Status 6-22 Job Box Detail Removable Memory Open 001/999 Store File FAX Box 08/08/2009 10:10 OPERATION GUIDE 7 Status / Job Cancel This chapter explains how to check the status and history of jobs and cancel the jobs being processed or waiting to be printed. This chapter also explains how to check the remaining amount of toner and paper and the status of devices, and how to cancel the fax communication. • • • • • • • • • Checking Job Status ...........................................................................7-2 Checking Job History ..........................................................................7-9 Sending the Job Log History.............................................................7-11 Pause and Resumption of Jobs ........................................................7-13 Canceling of Jobs .............................................................................7-13 Priority Override for Waiting Jobs .....................................................7-14 Reordering Print Jobs .......................................................................7-14 Checking the Remaining Amount of Toner and Paper......................7-15 Device/Communication .....................................................................7-16 OPERATION GUIDE 7-1 Status / Job Cancel Checking Job Status Check the status of jobs being processed or waiting to be printed. Available Status Screens The processing and waiting statuses of jobs are displayed as a list on the touch panel in four different screens - Printing Jobs, Sending Jobs, Sending Jobs - Timer waiting, and Storing Jobs. The following job statuses are available. Screen Job statuses to be displayed Printing Jobs • • • • • • • • Copy Printer FAX reception i-FAX reception E-mail reception Printing from Document Box Job Report /List Printing data from removable memory Sending Jobs • • • • • • • FAX transmission i-FAX transmission PC (SMB/FTP) transmission E-mail Application Multiple destination Sending Job FAX using Delayed transmission Storing Jobs • • • • • • Scan FAX i-FAX Printer Join Box Document Copy Box Document Displaying Status Screens Use the procedure below to display the Status screen. Status Status Job Type All epted Time Type 438 Log Scheduled Job 14:47 Job Name User Name 1 Press the Status/Job Cancel key. 2 The Status screen appears. Press either of [Printing Jobs], [Sending Jobs], or [Storing Jobs] to check the status. Status InProcess [email protected] To check the scheduled transmission job, press [Sending Jobs] and then [Scheduled Job]. 1/1 For an explanation of the screen, refer to Details of the Status Screens on page 7-3. Detail Cancel Printing Jobs Status 7-2 Sending Jobs Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 10:10 OPERATION GUIDE Status / Job Cancel Details of the Status Screens The items and keys displayed on the status screens are as follows. For information on how to display the Status screen, see Displaying Status Screens on page 7-2. Printing Jobs Status Screen Status Status Job Type Job No. Log 7 All End Date Type Job Name User Name Result 000001 10/10 09:50 doc10102008095050 AAAAA InProcess 000002 10/10 09:55 doc10102008095510 AAAAA Waiting 000003 10/10 10:00 doc10102008091000 AAAAA Waiting 5 6 1 2 8 Pause All Print Jobs Printing Jobs 3 4 9 10 Priority Override Cancel Sending Jobs Storing Jobs 11 Move Up 1/1 12 Detail Device/ Communication Paper/Supplies 08/08/2009 Status 10:10 7 The table below lists the items displayed in the Printing Jobs Status screen. No. Item / Key Detail 1 Job No. Acceptance No. of job 2 Accepted Time Accepted Time of job 3 Type Icons that indicate the job type Copy job Printer job FAX reception i-FAX reception E-mail reception Job from Document Box Report / List Data from Removable Memory 4 Job Name Job Name or file name 5 User Name User Name for the executed job 6 Status Status of job InProcess: Printing: Waiting: Pause: Canceling: OPERATION GUIDE The status before starting to print. Printing Print Waiting Pausing print job or error Canceling the job 7-3 Status / Job Cancel No. 7-4 Item / Key ] of Job Type Detail 7 [ Sorts by specific type of job 8 [Pause All Print Jobs] Pauses all the printing jobs. By pressing this key again, the printing jobs will be resumed. 9 [Cancel] Select the job to be canceled from the list, and press this key. 10 [Priority Override] Select the job to be overridden, and press this key. (Refer to Priority Override for Waiting Jobs on page 7-14) 11 [Move Up] In the list, select the job that you want to move up the job queue and press this key. (Refer to Reordering Print Jobs on page 7-14) 12 [Detail] Select the job for displaying detailed information from the list, and press this key. (Refer to Checking the Detailed Information of Histories on page 7-10) OPERATION GUIDE Status / Job Cancel Sending Jobs Status screen Status Status Job Type Job No. Accepted Time Type 438 14:47 1 2 Log Scheduled Job 7 All Job Name User Name Status InProcess [email protected] 3 4 5 6 1/1 8 9 Detail Cancel Printing Jobs Sending Jobs Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 Status 10:10 The table below lists the items displayed in the Sending Jobs Status screen. No. Item / Key Detail 1 Job No. Acceptance No. of job 2 Accepted Time Accepted Time of job 3 Type Icons that indicate the job type 7 Sending Job FAX Sending Job i-FAX Sending Job PC (SMB/FTP) Sending Job E-mail Sending Job Application Sending Job Multiple 4 Destination Destination (Either destination name, FAX number, E-mail address, or server name) 5 User Name User Name for the executed job 6 Status Status of job InProcess: The status before starting sending such as during scanning originals Sending: Sending Waiting: Sending Waiting Canceling: Canceling the job Pause: Pausing the job 7 [ Only selected type of jobs is displayed. 8 [Cancel] Select the job you want to cancel from the list, and press this key. 9 [Detail] Select the job whose detailed information you want to display from the list, and press this key. (Refer to Checking the Detailed Information of Histories on page 7-10) ] of Job Type OPERATION GUIDE 7-5 Status / Job Cancel Storing Jobs Status screen Status Status Job No. Log 7 All Job Type Accepted Time Type 438 14:47 1 2 Job Name User Name Status doc20070225144758 3 4 InProcess 5 6 1/1 8 9 Detail Cancel Printing Jobs Sending Jobs Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 Status 10:10 The table below lists the items displayed in the Storing Jobs Status screen. No. Display / Key Details 1 Job No. Acceptance No. of job 2 Accepted Time Accepted Time of job 3 Type Icons that indicate the job type Storing Job Scan Storing Job Printer Storing Job FAX Storing Job i-FAX Join Box Document Copy Box Document 7-6 4 Job Name Job name or file name is displayed. 5 User Name User Name for the executed job 6 Status Status of job InProcess: The status before starting to save such as during scanning originals Storing: Storing Data Canceling: Canceling the job Pause: Pausing the job 7 [ Only selected type of jobs is displayed. 8 [Cancel] Select the job you want to cancel from the list, and press this key. 9 [Detail] Select the job whose detailed information you want to display from the list, and press this key. (Refer to Checking the Detailed Information of Histories on page 7-10) ] of Job Type OPERATION GUIDE Status / Job Cancel Checking the Detailed Information of Jobs Check the detailed information of each job. Use the procedure below to check a job's information. 1 Press the Status/Job Cancel key. 2 Press [Printing Jobs], [Sending Jobs], or [Storing Jobs]. To check the scheduled transmission, press [Sending Jobs] and then [Scheduled Job]. 3 Status Status Job Type Job No. Log Scheduled Job Select the job whose details you wish to check from the list, and press [Detail]. All Accepted Time Type 438 14:47 Job Name User Name Detailed information of the selected job is displayed. Status InProcess [email protected] 1/1 7 Detail Cancel Printing Jobs Sending Jobs Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 Status Detail Job No.: 10:10 Use [ ] or [ information. 000080 Job No.: Status/Destination: 000080 Processing Job Type: Destination: Sending Job - E-mail Detail ] to see the next or previous page of ABCDE User Name: User1 Job Name: doc20070404115151 Accepted Time: 1/2 10:10:10 Close 08/08/2009 Status Detail Job No.: 10:10 In Sending Jobs, you can check the destination by pressing [Detail] in Status/Destination. 000080 Job No.: Status/Destination: 000080 Processing Job Type: Destination: Sending Job - E-mail Detail ABCDE User Name: User1 Job Name: doc20070404115151 Accepted Time: 10:10:10 1/2 Close Status OPERATION GUIDE 08/08/2009 10:10 7-7 Status / Job Cancel Detail Job No.: Status/Destination is displayed when address is selected. Press [Detail] to display the list. Press [ ] or [ ], select a destination and press [Detail]. Information on the selected job is displayed for checking. 000081 Job Type Type All Destination Status doc20070404131415 Sending User01 Waiting 1/2 4 To exit from the detailed information, press [Close]. Detail Close Status 7-8 08/08/2009 10:10 OPERATION GUIDE Status / Job Cancel Checking Job History Check the history of completed jobs. NOTE: Job history is also available by Embedded Web Server or Network Print Monitor from the computer. Available Job History Screens The job histories are displayed separately in three screens - Printing Jobs, Sending Jobs, and Storing Jobs. The following job histories are available. Screen Job histories to be displayed Printing Jobs • • • • • • • • Copy Printer FAX reception i-FAX reception E-mail reception Printing from Document Box Job Report / List Printing data from removable memory Sending Jobs • • • • • • FAX i-FAX PC (SMB/FTP) E-mail Application Multiple destination Storing Jobs • • • • • • Scan FAX i-FAX Printer Join Box Document Copy Box Document 7 Displaying Job History Screen The procedure for displaying Job History Screen is explained below. Status Status Job Type Job No. Log 1 Press the Status/Job Cancel key. 2 Press either of [Printing Jobs], [Sending Jobs], or [Storing Jobs] to check the log, and press [Log]. All End Date Type Job Name User Name Result 000080 01/25 14:14 doc20070225141427 Completed 000081 01/25 14:22 doc20070225142253 Completed 000082 01/25 14:23 doc20070225142310 Completed 000083 01/25 14:24 doc20070225142458 Error 000084 01/25 14:30 doc20070225143034 Completed 001/001 Detail Printing Jobs Sending Jobs Status OPERATION GUIDE Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 10:10 7-9 Status / Job Cancel Checking the Detailed Information of Histories Check the detailed information of each history. Display of the detailed information of Job Finish history Use the procedure below to check the job finish history. Status Status Job Type Job No. 1 Press the Status/Job Cancel key. 2 Press [Printing Jobs], [Sending Jobs] or [Storing Jobs] and then [Log]. 3 Select the job to check details from the list, and press [Detail]. Log All End Date Type Job Name User Name Detailed information of the selected job is displayed. Result 000080 01/25 14:14 doc20070225141427 Completed 000081 01/25 14:22 doc20070225142253 Completed 000082 01/25 14:23 doc20070225142310 Completed 000083 01/25 14:24 doc20070225142458 Error NOTE: To check the information of the next/previous 000084 01/25 14:30 doc20070225143034 Completed page, press [ 001/001 ] or [ ]. Detail Printing Jobs Status Sending Jobs Storing Jobs Device/ Communication Paper/Supplies 08/08/2009 10:10 4 7-10 To exit from the detailed information, press [Close]. OPERATION GUIDE Status / Job Cancel Sending the Job Log History You can send the job log history by e-mail. You can either send it manually as needed or have it sent automatically whenever a set number of jobs is reached. Setting the destination Set the destination to which job log histories are sent. Use the procedure below to set the destination. 1 Press the System Menu key. 2 Press [Report], [Next] of Sending Job Log History and then [Change] of Destination. 3 To enter a new e-mail address, press [E-mail Address Entry]. Press [E-mail Address], enter the destination email address and then press [OK]. 4 To set an address from the address book, press [Email Address Book]. Press [Address Book]. Select the destination from the address book and press [OK]. NOTE: For information on specifying destinations, refer to Specifying Destination on page 3-30. The selected e-mail addresses is displayed. NOTE: You can view information on the selected destinations by pressing [Detail]. 5 Press [OK]. Automatic Job Log History Transmission This function automatically sends the job log history to the specified destinations whenever a set number of jobs has been logged. Use the procedure below to set automatic job log history transmission. OPERATION GUIDE 1 Press the System Menu key. 2 Press [Report], [Next] of Sending Job Log History and then [Change] of Auto Sending. 7-11 7 Status / Job Cancel Report - Auto Sending 3 Press [On] and enter the number of jobs in the job log history print by using [+]/[-] or the numeric keys. You can enter any number between 1 and 1500. 4 Press [OK]. Send job log history to the specified destination after a set number of jobs have been logged. Off Jobs (1 - 1500) On 100 Cancel Status OK 08/08/2009 10:10 Manual Job Log History Transmission You can also send the job log history to the specified destinations manually. Use the procedure below to send the job log history manually. 1 Press the System Menu key. 2 Press [Report], [Next] of Sending Job Log History and then [Execute] of Send Job Log History. When the confirmation screen appears, press [Yes]. The job log history is sent. Setting E-mail Subject Set the subject automatically entered when sending job log histories by e-mail. Use the procedure below to set the subject. 1 Press the System Menu key. 2 Press [Report], [Next] of Sending Job Log History and then [Change] of Subject. 3 Enter an e-mail subject not more than 60 characters. NOTE: Refer to the Character Entry Method on Appendix-10 for details on entering characters. 4 7-12 Check that the entry is correct and press [OK]. OPERATION GUIDE Status / Job Cancel Pause and Resumption of Jobs Pause /resume all printing jobs in printing/waiting. The procedure for pausing and resuming jobs is explained below. Status Status Job Type Job No. 1 Press the Status/Job Cancel key. 2 Press [Pause All Print Jobs] on the Printing Jobs Status screen. Printing is paused. 3 When resuming the printing of jobs that have been paused, press [Resume All Print Jobs]. Log All End Date Type Job Name User Name Result 000001 10/10 09:50 doc10102008095050 AAAAA InProcess 000002 10/10 09:55 doc10102008095510 AAAAA Waiting 000003 10/10 10:00 doc10102008091000 AAAAA Waiting Pause All Print Jobs Printing Jobs ancel Priority Override Sending Jobs Storing Jobs Status Move Up 1/1 Detail Dev ce/ Communication Paper/Supplies 08/08/2009 10:10 Canceling of Jobs For more information on canceling jobs, refer to the Canceling Jobs on page 3-42. OPERATION GUIDE 7-13 7 Status / Job Cancel Priority Override for Waiting Jobs Priority Override function suspends the current job and prints the job in waiting first. The procedure for using Priority Override is explained below. Status Status Job Type Job No. 1 Press the Status/Job Cancel key. 2 Press [Printing Jobs]. 3 Select the job to be given priority, and press [Priority Override]. 4 Press [Yes] in the confirmation screen. The current job in printing is suspended, and the job for override printing starts. 5 When the Priority Override is completed, the printing job that has been suspended will be resumed. Log All End Date Type Job Name User Name Result 000001 10/10 09:50 doc10102008095050 AAAAA InProcess 000002 10/10 09:55 doc10102008095510 AAAAA Waiting 000003 10/10 10:00 doc10102008091000 AAAAA Waiting Pause All Print Jobs Priority Override Cancel Printing Jobs Sending Jobs Move Up Storing Jobs 1/1 Detail Dev ce/ Communication Paper/Supplies 08/08/2009 Status 10:10 Reordering Print Jobs This function allows you to select a queued print job and raise its output priority. The procedure for reordering print jobs is explained below. Status Status Job Type Job No Log All End Date Type Job Name User Name doc10102008095050 AAAAA InProcess 000002 10/10 09:55 doc10102008095510 AAAAA Waiting 000003 10/10 10:00 doc10102008091000 AAAAA Waiting Printing Jobs Status 7-14 Cancel Sending Jobs Priority Override Storing Jobs Move Up Press the Status/Cancel key. 2 Press the [Printing Jobs]. 3 Select the job to be assigned a higher priority and press [Move Up]. The priority of the selected job is increased by 1 . Result 000001 10/10 09:50 Pause All Print Jobs 1 To further raise the job's priority, press [Move Up] again. Each time you press [Move Up], the priority increases by 1. 1/1 Detail Dev ce/ Communication Paper/Supplies 08/08/2009 10:10 OPERATION GUIDE Status / Job Cancel Checking the Remaining Amount of Toner and Paper Check the remaining amount of toner, paper, and staples on the touch panel. Use the procedure below to check the remaining amounts. Status Toner Information Toner Black (K) Paper Status Waste Toner OK Printing Jobs Press the Status/Job Cancel key. 2 Press [Paper/Supplies].Check the remaining amount of toner and the status of a waste toner box in Toner Information, and the remaining amount of paper in each paper source in Paper Others Size 100% 1 Type Status Ledger Plain 30% Ledger Plain 30% Letter Plain 30% Letter Plain 30% Letter Plain 0% Sending Jobs Storing Jobs Status Type Staple A Device/ Communication Status OK Paper/Supplies 08/08/2009 10:10 7 The items you can check are described below. Remaining amount of toner You can check the remaining amount of each color toner as one of 11 levels from 100 to 0%. Status of waste toner box You can check the status of waste toner box. Paper You can check the size, orientation, type, and remaining amount of paper in each paper source.The remaining amount of paper is shown by 11 levels from 100 to 0%, however, the paper in the multi purpose tray is shown by 2 levels as 100% and 0%. Others You can check the status of staples and punch waste box. NOTE: If the optional built-in finisher, document finisher, or 3,000 sheet document finisher and punch unit are installed, the Others section provides the status of the punch waste box and whether or not staples are available. OPERATION GUIDE 7-15 Status / Job Cancel Device/Communication Configure the devices/lines installed or connected to this machine or check their status. You can also control devices depending on their status. Displaying Device/Communication Screen The procedure for using the Device/Communication screen is explained below. 1 Press the Status/Job Cancel key. 2 Press [Device/Communication] The screen to check the status or configure the devices is displayed. Check of Device Status Status Scanner Hard Disk Ready. Overwriting... Printer Ready. Removable Memory Not connected. Format Remove FAX Port 2 FAX Port 1 Dialing... Line Off FAX Receiving... Manual RX Line Off i-FAX Log Printing Jobs Status Sending Jobs Storing Jobs Device/ Communication Check New FAX Paper/Supplies 08/08/2009 10:10 The items you can check are described below. Scanner The status of an original scanning in the document processor (optional) or the error information (paper jam, opened cover, etc.) is displayed. Printer Error information such as paper jam, out of toner, or out of paper, and status such as waiting or printing are displayed. Hard Disk The information such as formatting, overwriting for erasure, and error occurrence is displayed. 7-16 OPERATION GUIDE Status / Job Cancel Configuring the Devices Status Scanner Hard Disk Ready. Overwriting... Printer Ready. Removable Memory Not connected. Format Remove FAX Port 2 FAX Port 1 Dialing... Line Off FAX Receiving... Manual RX Line Off i-FAX Log Printing Jobs Sending Jobs Storing Jobs Device/ Communication Check New FAX Paper/Supplies 08/08/2009 Status 10:10 Detailed information on controlling devices is given below. Removable Memory (USB Memory) • The usage and capacity of the external media connected to this machine are displayed. • Press [Format] to format external media. • Press [Remove] to safely remove the external media. For details, refer to Removing the USB Memory in the next section. FAX Port 1, FAX Port 2 • The information such as sending/receiving and dialing is displayed. • Press [Line Off] to cancel a fax in sending/receiving. For details, refer to Canceling FAX Communication on page 7-18 in the section afterwards. • Press [Manual RX] to start a fax. Use this function when you want to talk to the sender before receiving the fax originals. For details, refer to the Operation Guide of FAX kit. • Press [Log] to display the fax transmission history. For details, refer to the Operation Guide of FAX kit. Removing the USB Memory There is a way to remove the USB memory safely. Use the procedure below to remove the USB memory. Status Scanner Hard Disk Ready. Overwriting... 1 Press the Status/Job Cancel key. 2 Press [Device/Communication] > [Remove] in Removable Memory. 3 When Device can be removed safely. is displayed, remove the USB memory. Printer Ready. Removable Memory Not connected. Format Remove FAX Port 2 FAX Port 1 Dialing... Line Off FAX Printing Jobs Receiving... Manual RX Line Off i-FAX Log Sending Jobs Status OPERATION GUIDE Storing Jobs Device/ Communication Check New FAX Paper/Supplies 08/08/2009 10:10 7-17 7 Status / Job Cancel Canceling FAX Communication Cancel fax communication. Use the procedure below to cancel the fax communication. Status Scanner Hard Disk Ready. Overwriting... 1 Press the Status/Job Cancel key. 2 Press [Device/Communication] > [Line Off] in FAX Port 1 or FAX Port 2. 3 Press [Yes] in the confirmation screen. The line is disconnected, and the fax communication is canceled. Printer Ready. Removable Memory Not connected. Format Remove FAX Port 2 FAX Port 1 Dialing... Line Off FAX Printing Jobs Status 7-18 Receiving... Manual RX Line Off i-FAX Log Sending Jobs Storing Jobs Device/ Communication Check New FAX Paper/Supplies 08/08/2009 10:10 OPERATION GUIDE 8 Default Setting (System Menu) This chapter explains how to configure various settings of the machine using the menus on the operation panel. • • • • • • • • • • • • • • • • • • • • Common Settings ...............................................................................8-2 Copy Settings....................................................................................8-26 Sending Settings...............................................................................8-29 Document Box Settings ....................................................................8-32 Printer Settings .................................................................................8-34 Printing Reports/Sending Notice.......................................................8-39 Adjustment/Maintenance ..................................................................8-42 Date/Timer ........................................................................................8-47 Editing Destination (Address Book/Adding One Touch Keys)...........8-51 Internet Browser Setup .....................................................................8-58 Applications.......................................................................................8-60 System Initialization ..........................................................................8-63 Restarting the System.......................................................................8-63 Network Setup ..................................................................................8-64 Secure Protocol ................................................................................8-69 Interface Block Setting ......................................................................8-72 Security Level (Security Level setting)..............................................8-73 Document Guard Setting ..................................................................8-73 Optional Functions ............................................................................8-75 Accessibility Display (Enlarged Touch Panel Display) ......................8-77 OPERATION GUIDE 8-1 Default Setting (System Menu) Common Settings Common settings include; • Switching the Language for Display [Language] …8-2 • Default Screen …8-2 • Sound …8-3 • Original/Paper Settings …8-4 • Switching Unit of Measurement …8-11 • Error Handling …8-12 • Paper Output …8-14 • Orientation Confirmation …8-15 • Function Defaults …8-15 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Switching the Language for Display [Language] Select the language displayed on the touch panel. Use the procedure below to select the language. 1 Press the System Menu key. 2 Press [Common Settings] and then [Change] of Language. 3 Press the key for the language you want to use. 4 Press [OK]. The touch panel language will be changed. Default Screen Select the screen appearing right after start-up (default screen). The options are as follows. The table below lists the available screens. Item 8-2 Description Copy The Copy screen (the screen shown when the Copy key is pressed) appears. Send The Send screen (the screen shown when the Send key is pressed) appears. Status The Status/Job Cancel screen (the screen shown when the Status/ Job Cancel key is pressed) appears. OPERATION GUIDE Default Setting (System Menu) Item Description Document Box The Document Box screen (the screen shown when the Document Box key is pressed) appears. Program The Program screen (the screen shown when the Program key is pressed) appears. Application The Application selecting screen (the screen shown when the Application key is pressed) appears. Accessibility Copy The Accessibility Copy screen (the screen shown when the Accessibility Display key is pressed in the Copy screen) appears. Accessibility Send The Accessibility Send screen (the screen shown when the Accessibility Display key is pressed in the Send screen) appears. Application name (Maximum 6 applications) For example, Internet Browser Each application is activated and the initial screen appears. Use the procedure below to select the default startup screen. 1 Press the System Menu key. 2 Press [Common Settings] and then [Change] of Default Screen. 3 Select the screen to be displayed as the default screen. 8 NOTE: The application names appear if the applications are installed and officially licensed on. 4 Press [OK]. Sound Set options for buzzer sound during the machine operations. The table below lists the buzzer types and their settings and details. Item Value Description Volume 0 (Mute), 1 (Minimum) to 5 (Maximum) Set the buzzer volume level. Key Confirmation Off, On Emit a sound when the control panel and touch panel keys are pressed. Job Finish Off, On Emit a sound when a print job is normally completed. Ready Off, On Emit a sound when the warm-up is completed. Warning Off, On Emit a sound when errors occur. OPERATION GUIDE 8-3 Default Setting (System Menu) Use the procedure below to set the sound options. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Sound and then [Next] of Buzzer. 3 Press [Change] of Volume, Key Confirmation, Job Finish, Ready, or Warning. 4 Select the buzzer volume level, or other sound options. Original/Paper Settings Register additional types and sizes of originals and paper. Custom Original Size Setup Set up frequently-used custom original sizes. The custom size options are displayed on the screen to select original size. The dimensions available are as follows. The table below lists the sizes that can be registered. Input units Dimensions Inch models X: 2 to 17" (in 0.01" increments) Y: 2 to 11.69" (in 0.01" increments) Metric models X: 50 to 432 mm (in 1 mm increments) Y: 50 to 297 mm (in 1 mm increments) Up to four custom original sizes can be added. Use the procedure below to set a custom original size. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Next] of Custom Original Size. 3 Press [Change] of any one of Custom 1 to Custom 4, on which you wish to register the size. 4 Press [On], and then press [+],[–] or numeric keys to enter X(horizontal) and Y (vertical) dimensions. 5 Press [OK]. 6 Move to the copy, send, or document box screen and press the Reset key. Adding a Custom Size and Media Type for Paper to Print Set up a maximum of four frequently-used custom paper sizes. The custom size options are displayed on the screen to select paper set in the multi purpose tray. The table below lists the sizes that can be registered. Input units 8-4 Dimensions Inch models H: 5.83 to 17" (in 0.01" increments) V: 3.86 to 11.69" (in 0.01" increments) Metric models H: 148 to 432 mm (in 1 mm increments) V: 98 to 297 mm (in 1 mm increments) OPERATION GUIDE Default Setting (System Menu) Up to four custom paper sizes can be added. Select media type for each paper size. Media type: Plain, Transparency, Rough, Vellum, Labels, Recycled, Preprinted, Bond, Cardstock, Color, Prepunched, Letterhead, Thick, Envelope, High Quality, Custom 1-8 NOTE: Refer to Paper Weight on page 8-7 for Custom 1-8 for media type. Use the procedure below to select a custom paper size and media type. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Next] of Custom Paper Size. 3 Press [Change] of any one of Custom 1 to Custom 4, on which you want to register the size. 4 Press [On], and then press [+],[–] or numeric keys to enter X (horizontal) and Y (vertical) dimensions. 5 Press [Media Type] to select the type of paper and press [OK] if necessary. 6 Press [OK]. 7 Move to the copy or document box screen and press the Reset key. 8 Paper Size and Media Type Setup for Cassettes Select paper size and media type for Cassette 1, 2 and optional paper feeders (Cassette 3 and 4). The available paper sizes and media types are shown in the table below. Item Paper Size Auto Automatically detect paper size. Select Metric or Inch for paper size. Standard Sizes 1 Available options are as follows: Inch models: Ledger, Legal, Letter, Letter-R, Statement-R, 8.5×13.5", Oficio II Metric models: A3, B4, A4, A4-R, B5, B5-R, A5-R, Folio Standard Sizes 2 Select a standard size except that selected in Standard Sizes 1. Inch models: A3, B4, A4, A4-R, A5-R, B5, B5-R, Folio, 8K, 16K, 16K-R Metric models: Ledger, Legal, Letter, Letter-R, Statement-R, 8.5×13.5", Oficio II, 8K, 16K, 16K-R Media Type * ** Description Plain (105 g/m2 or less), Rough, Vellum (64 g/m2 or less), Recycled, Preprint**, Bond*, Color, Prepunched**, Letterhead**, High Quality, Custom 1-8* To change to a media type other than Plain, refer to Paper Weight on page 8-7. When the paper weight settings shown below are selected, the media indicated for each setting cannot be selected. • Custom 1 to 8: Heavy1, Heavy 2, Heavy3, or Extra Heavy To print on preprinted or prepunched paper or on letterhead, refer to Special Paper Action on page 8-10. OPERATION GUIDE 8-5 Default Setting (System Menu) Use the procedure below to select the paper size and media type for each cassette. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings, [Next] of Cassette Setting, [Next] of Cassette 1 to Cassette 4, on which you want to register the size, and then [Change] of Paper Size. 3 To detect paper size automatically, press [Auto] and select Metric or Inch for Paper Size. To select paper size, press [Standard Sizes 1] or [Standard Sizes 2] for Paper Size. 4 Press [OK]. The previous screen reappears. 5 Press [Change] of Media Type to select media type and press [OK]. Paper Size and Media Type Setup for Multi Purpose Tray Select size and media type for multi purpose tray. Set up frequently-used size and media type before use. The available paper sizes and media types are shown in the table below. Item Paper Size Auto Automatically detect paper size. Select Metric or Inch for paper size. Standard Sizes 1 Available options are as follows: Inch models: Ledger, Legal, Letter, Letter-R, Statement-R, 8.5×13.5", Oficio II, Executive Metric models: A3, B4, A4, A4-R, B5, B5-R, A5-R, B6-R, A6-R, Folio Standard Sizes 2 Select a standard size except that selected in Standard Sizes 1. Inch models: A3, B4, A4, A4-R, B5, B5-R, A5-R, B6-R, A6-R, Folio, 8K, 16K, 16K-R Metric models: Ledger, Legal, Letter, Letter-R, Statement-R, 8.5×13.5", Oficio II, Executive, 8K, 16K, 16K-R Others Select special standard sizes or custom sizes*. ISO B5, Envelope #10 (Commercial #10), Envelope #9 (Commercial #9), Envelope #6 (Commercial #6 3/4), Envelope Monarch, Envelope DL, Envelope C5, Envelope C4, Hagaki, Oufuku Hagaki, Youkei 4, Youkei 2 Size Entry Enter a size not displayed in the standard sizes. Inch models: H: 5.83 to 17" (in 0.01" increments) V: 3.86 to 11.69" (in 0.01" increments) Metric models: V: 98 to 297 mm (in 1 mm increments) H: 148 to 432 mm (in 1 mm increments) Media Type * ** Description Plain (105 g/m2 or less), Transparency, Rough, Vellum (64 g/m2 or less), Labels, Recycled, Preprint**, Bond, Cardstock, Color, Prepunched**, Letterhead**, Envelope, Thick (91 g/m2 and more), High Quality, Custom 1-8** Refer to Adding a Custom Size and Media Type for Paper to Print on page 8-4 for selecting Custom 1- 4 for Custom Paper Size. Refer to Paper Weight on page 8-7 for selecting Custom 1- 8 from Media Type. To print on preprinted or prepunched paper or on letterhead, refer to Special Paper Action on page 8-10. NOTE: To change to a media type other than Plain, refer to Paper Weight on page 8-7 8-6 OPERATION GUIDE Default Setting (System Menu) Use the procedure below to select the paper size and media type for manual paper feed. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings, [Next] of MP Tray Setting and then [Change] of Paper Size. 3 To detect paper size automatically, press [Auto] and select Metric or Inch for Paper Size. To select paper size, press [Standard Sizes 1], [Standard Sizes 2], [Others] or [Size Entry] for Paper Size. If you select [Size Entry], press [+], [–] to enter X (horizontal) and Y (vertical) dimensions. Press [# Keys] to enter the paper size using the numeric keys. 4 Press [OK]. The previous screen reappears. 5 Press [Change] of Media Type to select the media type and press [OK]. Paper Weight Select weight for each media type. The options for media type and weight of paper are as follows. Paper types and weights 8 Y: Available N: Not available Paper Weight Weight (g/m2), Media type Light 64g/m2 or less Normal 1 Normal 2 Normal 3 Heavy 1 Heavy 2 Heavy 3 Extra Heavy 60g/m2 to 75g/m2 76g/m2 to 90g/m2 91g/m2 to 105g/m2 106g/m2 to 135g/m2 136g/m2 to 163g/m2 164g/m2 and more Transparencies Plain Y Y Y (default) Y N N N N Transparency N N N N N N N Y (default) Rough Y Y Y Y (default) Y N N* N Vellum Y (default) Y Y Y N N N N Labels N N N N Y (default) Y Y N Recycled Y Y Y (default) Y N N N N Preprinted Y Y Y (default) Y N N N N Bond Y Y Y Y (default) Y N N* N Cardstock N N N N Y Y (default) Y N Color Y Y Y (default) Y N N N N Prepunched Y Y Y (default) Y N N N N Letterhead Y Y Y (default) Y Y N N N Thick N N N Y Y Y (default) Y* N* OPERATION GUIDE 8-7 Default Setting (System Menu) Light Normal 1 Normal 2 Normal 3 Heavy 1 Heavy 2 Heavy 3 Extra Heavy Envelope N N N N Y Y (default) Y N High Quality Y Y Y (default) Y Y N N N Custom 1-8 Y Y Y (default) Y Y* Y* Y* Y* Paper Weight * When Heavy 1, Heavy 2, Heavy 3, or Extra Heavy is selected, the media type cannot be selected for the cassettes. For Custom 1-8, settings for duplex printing and media type name can be changed. Item Duplex Description Prohibit Duplex printing not allowed. Permit Duplex printing allowed. Name Change names for Custom 1-8. Names should be not more than 15 characters. Selecting media type at multi purpose tray, the name after change will be displayed. Use the procedure below to set the paper weight. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Next] of Media Type Setting. 3 Press [Next] for the media type whose weight you want to change. 4 Press [Change] of Paper Weight. 5 Select the weight and press [OK]. 6 Press [Close]. The previous screen reappears. 7 To change the duplex printing settings for Custom 1 (-8), press [Next] of Custom 1(-8) and then [Change] of Duplex. Select [Prohibit] or [Permit] and press [OK]. The previous screen reappears. 8 Press [Close]. 9 To change the name for Custom 1(-8), press [Next] of Custom 1(-8) and then [Change] of Name. Enter the name and press [OK]. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 8-8 OPERATION GUIDE Default Setting (System Menu) Default Paper Source Select the default paper source from Cassette 1-4 and Multi Purpose Tray. NOTE: [Cassette 3] is displayed when either of the optional paper feeder or 3,000 sheet paper feeder is installed, and [Cassette 4] is displayed when the optional paper feeder is installed. Use the procedure below to select the default paper source. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Change] of Default Paper Source. 3 Select a paper cassette for the default setting. 4 Press [OK]. 5 Move to the copy or document box screen and press the Reset key. Automatic Detection of Originals (Available for metric models only) Automatically detect originals of special or non-standard size. 8 The table below lists the special or non-standard original sizes. Item Description A6/Hagaki As A6 and Hagaki are similar in size, select either one of them for automatic detection. Folio Select Folio for automatic detection. 11x15" Select the 11×15" size for automatic detection. Use the procedure below to set automatic detection of originals. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Change] of Original Auto Detect. 3 Select [A6] or [Hagaki] of A6/Hagaki. Select [Off] to disable automatic detection or [On] to enable automatic detection of Folio and 11x15" respectively. 4 Press [OK]. Media for Auto Selection Select a default media type for auto paper selection when [Auto] is selected of Paper Selection. If Plain is selected, the paper source with plain paper loaded in the specific size is selected. Select [All Media Types] for the paper source with any kind of paper loaded in the specific size. OPERATION GUIDE 8-9 Default Setting (System Menu) Use the procedure below to select the paper size and media type used by Auto Selection. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings and then [Change] of Media for Auto (B & W). 3 Select [All Media Types] or any media type for paper selection. 4 Press [OK]. Paper Source for Cover Paper Select paper source for cover paper from Cassette 1-4 or Multi Purpose Tray. Cover is used for Booklet (see page 4-19) and Cover (see page 4-21) modes. NOTE: [Cassette 3] is displayed when either of the optional paper feeder or 3,000 sheet paper feeder is installed, and [Cassette 4] is displayed when the optional paper feeder is installed. Use the procedure below to select the paper source for the cover. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings, [ Cover. 3 Select the paper source to load cover paper. 4 Press [OK]. ] and then [Change] of Paper Source for Special Paper Action When printing on Prepunched, Preprint, and Letterhead, punch-holes might not be aligned or the print direction might be upside-down depending on how originals are set and the combination of copying functions. In such a case, select [Adjust Print Direction] to adjust the print direction. When paper orientation is not important, select [Speed Priority]. The table below lists the available settings and their details. Item 8-10 Description Adjust Print Direction Adjust print direction. Print speed is a little slower. Select this item to print on Prepunched, Preprint and Letterhead. Speed Priority Give the job speed top priority and disregard the paper orientation. Select this item when paper orientation is not important. OPERATION GUIDE Default Setting (System Menu) If you select [Adjust Print Direction], load paper according to the steps below. Example: copying on Letterhead Original Paper Finished Cassette Multi Purpose Tray Original Paper Finished Cassette Multi Purpose Tray NOTE: When loading cover paper in a cassette or multi purpose tray, load the face, on which printing is supposed to be done, upward. Use the procedure below to specify the actions performed for special paper types. 1 Press the System Menu key. 2 Press [Common Settings], [Next] of Original / Paper Settings, [ Action. 3 Select [Adjust Print Direction] or [Speed Priority]. 4 Press [OK]. 8 ] and then [Change] of Special Paper Switching Unit of Measurement Select inch or metric for the unit for paper dimensions. Use the procedure below to change the input units. 1 Press the System Menu key. 2 Press [Common Settings] and then [Change] of Measurement. 3 Select [mm] for metric or [inch] for inch. 4 Press [OK]. OPERATION GUIDE 8-11 Default Setting (System Menu) Error Handling Select whether to cancel or continue the job when error has occurred. The possible errors and what to do for the errors are as follows. Duplexing Error Select what to do when duplex printing is not possible for the selected paper size and media type. Item Description 1-sided Printed in 1-sided Display Error Error message to cancel printing is displayed. Finishing Error Select alternative actions when finishing (stapling or offsetting) is not available for the selected paper size or media type. Processing Description Ignore The setting is ignored and the job is printed. Display Error Error message to cancel printing is displayed. No Staple Error Select what to do when staples run out during printing. Item Description Ignore Printing continues without stapling. Display Error Error message to cancel printing is displayed. NOTE: The messages are displayed when the optionalbuilt-in finisher, document finisher, or 3,000 sheet document finisher is installed. Stapling Limit Error Select what to do when stapling capacity is exceeded during printing. Item Description Ignore Printing continues without stapling. Display Error Error message to cancel printing is displayed NOTE: The messages are displayed when the optionalbuilt-in finisher, document finisher, or 3,000 sheet document finisher is installed. 8-12 OPERATION GUIDE Default Setting (System Menu) Punch Waste Full Error Select what to do when the punch waste box becomes full during printing. Item Description Ignore Printing continues without punching. Display Error Error message to cancel printing is displayed. NOTE: The messages are displayed when the optional 3,000 sheet document finisher and punch unit are installed. Paper Mismatch Error Select what to do when the selected paper size or type does not match paper size or type loaded in the specified paper source while printing from the computer. Processing Description Ignore The setting is ignored and the job is printed. Display Error Error message to cancel printing is displayed. 8 Use the procedure below to specify the settings for error handling. 1 Press the System Menu key. 2 Press [Common Settings] and then [Next] of Error Handling. 3 Press [Change] at the error you wish to change the handling. 4 Select the error handling method in the selection screen for each of the errors and then press [OK]. 5 The previous screen appears. To set the handling for a different error, repeat steps 3 and 4. OPERATION GUIDE 8-13 Default Setting (System Menu) Paper Output Select output tray respectively for copy jobs, print jobs from Custom Box, computers, and FAX RX data. The options are as follows. Output Tray Descriptions Top Tray Delivery on Top Tray of the machine. Tray A, Tray B*, Tray C* Delivery to trays A to C in the optional 3,000 sheet document finisher. Finisher Tray* Delivery on Tray set to the optional built-in finisher or document finisher. Job Separator Delivery on the optional job separator. Tray 1 to 7* Delivery to trays 1 to 7 in the optional mailbox (tray 1 is the top tray). * Select [Face Up] (print surface up) or [Face Down] (print surface down) for paper orientation at output. NOTE: The optional job separator, built-in finisher, document finisher, or 3,000 sheet document finisher are required. FAX RX data output can be specified when the optional fax kit is installed. Use the procedure below to select the output tray. 1 Press the System Menu key. 2 Press [Common Settings] and then [Next] of Paper Output. 3 Press [Change] of Copy/Custom Box, Printer, or FAX Port 1 or FAX Port 2. NOTE: FAX Port 1 appears when the optional fax kit is installed. If you have 2 optional fax kits installed, Fax Port 2 appears. You can specify the output tray for the second kit (Dual FAX). 4 Select Output Tray. For [Finisher Tray], [Tray B], [Tray C] or [Tray 1] to [Tray 7], select [Face Up] (print surface up) or [Face Down] (print surface down) as the paper orientation at output. 5 Press [OK]. 6 When selecting [Face Up] (print surface up) as the paper orientation at output, press [Page Order with Face Up] and then select the order of the output pages from [Ascending] or [Descending]. NOTE: Selecting [Descending] accelerates the starting time of copying. 7 When changing the output tray of Copy/Custom Box, move to the copy or document box screen and press the Reset key. 8-14 OPERATION GUIDE Default Setting (System Menu) Orientation Confirmation Select whether to display a screen for selecting the orientation of the originals to be placed on the platen when using the following functions. (For more information, refer to page 4-10 for Original Orientation.) • Duplex • Memo mode • Margin/Centering originals • Page numbering • Border erase • Booklets • Combine mode • Staple/Punch (optional feature) Orientation Confirmation Setting Use the procedure below to select the default Orientation Confirmation setting. 1 Press the System Menu key. 2 Press [Common Settings] and [Change] of Orientation Confirmation. 3 Select the default for [Off] or [On]. 4 Press [OK]. Function Defaults 8 Defaults are the values automatically set after the warm-up is completed or the Reset key is pressed. Set the defaults for available settings such as copying and sending. Setting the frequently-used values as defaults makes subsequent jobs easier. IMPORTANT: When you have changed the defaults, to enable the change immediately, move to the copy, send, or document box screen and press the Reset key. Original Orientation Set the original orientation defaults. The available default settings are shown below. Item Description Top Edge Top Select the original's top edge at the top. Top Edge Left Select the original's top edge at the left. Refer to page 4-10 for Original Orientation. Use the procedure below to select the default orientation when originals are placed on the platen. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select [Top Edge Top] or [Top Edge Left] for the default. 4 Press [OK]. OPERATION GUIDE ], [Next] of Function Defaults and then [Change] of Original Orientation. 8-15 Default Setting (System Menu) Continuous Scan Set the continuous scan defaults. The available default settings are shown below. Item Description Off Continuous scan not performed On Continuous scan performed Refer to page 4-10 for Original Orientation. Use the procedure below to select the default settings for continuous scanning. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select [Off] or [On] for the default. ], [Next] of Function Defaults and then [Change] of Continuous Scan. Use the procedure below to select the default quality setting for originals. 4 Press [OK]. Original Image Set the default original document type. The available default settings are shown below. Item Description Text+Photo Text and photos together. Photo For photos taken with a camera. Text Only text, no photos. for OCR Image quality suitable for OCR software.* Printed Document For documents printed from this machine. * This function is only available for black and white mode. Use the procedure below to select the default quality setting for originals. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default original image. 4 Press [OK]. ], [Next] of Function Defaults and then [Change] of Original Image. Scan Resolution Select the default scanning resolution. The options are 600x600dpi, 400x400dpi Ultra Fine, 300x300dpi, 200x400dpi Super Fine, 200x200dpi Fine, 200x100dpi Normal. Use the procedure below to select the default resolution setting. 8-16 OPERATION GUIDE Default Setting (System Menu) 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default resolution. 4 Press [OK]. ], [Next] of Function Defaults and then [Change] of Scan Resolution. Color Selection (Send/Store) Select the default color mode for scanning documents. The available default settings are shown below. Color mode Description Auto Color (Color/Gray) Automatically recognize whether the document is color or black and white, and scan color documents in Full Color and black and white documents in Grayscale. Auto Color (Color/B & W) Automatically recognize whether the document is color or black and white, and scan color documents in Full Color and black and white documents in Black and White. Full Color Scan document in full color. Grayscale Scan document in grayscale for smoother and finer finish. Black & White Scan document in black and white. File size is smaller than Full Color or Grayscale. 8 Use the procedure below to select the default color mode. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default color mode. 4 Press [OK]. ], [Next] of Function Defaults and then [Change] of Color Select.(Send/Store). File Format Select the default file type to send the scanned originals. The available default settings are shown below. Item Description PDF Send files in PDF format. TIFF Send files in TIFF format. JPEG Send files in JPEG format. XPS Send files in XPS format. High Comp. PDF Send files in High Comp. PDF format (refer to page 5-14). NOTE: Refer to page 5-12 for file formats. OPERATION GUIDE 8-17 Default Setting (System Menu) Use the procedure below to select the default file format. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default file format. 4 Press [OK]. ], [Next] of Function Defaults and then [Change] of File Format. File Separation Select the default file separation setting. The available default settings are shown below. Item Description Off No file separation performed (all the pages are compiled in one file). Each Page Each scanned page is created into a separate file. NOTE: Refer to page 5-13 for file separation. Use the procedure below to select the default file separation. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default for [Off] or [Each Page]. ], [Next] of Function Defaults and then [Change] of File Separation. Press [OK]. Density Set the default density. The available default settings are shown below. Item Description Manual (Normal 0) Set to (Normal 0) in the Manual density. Auto Set to Auto density. Use the procedure below to select the default density. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default density. 4 Press [OK]. 8-18 ], [Next] of Function Defaults, [ ] and then [Change] of Density. OPERATION GUIDE Default Setting (System Menu) Zoom Select the enlarged/reduced default when paper size/sending size changed after the originals set. The available default settings are shown below. Item Description 100% Copy (send/save) at actual size (100%). Auto Automatically reduce or enlarge the originals to match paper size/ sending size. Use the procedure below to select the default zoom setting. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the default zoom setting. 4 Press [OK]. ], [Next] of Function Defaults, [ ] and then [Change] of Zoom. File Name Entry Set an automatically entered name (default) for jobs. Additional information such as Date and Time and Job No. can also be set. NOTE: Refer to page 4-35 and page 5-25 for name entry. Use the procedure below to set the default file name. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Press [File Name] to enter the file name in not more than 32 characters. ], [Next] of Function Defaults, [ ] and then [Change] of File Name Entry. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 4 Press [OK]. 5 Press [Date and Time] to add the date/time to the job, or press [Job No.] to add the job number to the job. The added information will be displayed in Additional Info. 6 Press [OK]. E-mail Subject/Body Set the subject and body automatically entered (default subject and body) when sending the scanned originals by E-mail. NOTE: Refer to Send as E-mail on page 3-24. OPERATION GUIDE 8-19 8 Default Setting (System Menu) Use the procedure below to set the default e-mail subject and message body. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Press [Subject] to enter an E-mail subject not more than 60 characters. ], [Next] of Function Defaults, [ ], and then [Change] of E-mail Subject/Body. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 4 Press [OK]. 5 Press [Body] to enter an E-mail Body not more than 500 characters. 6 Press [OK]. 7 Check that the entries are correct and press [OK]. Border Erase Default Set the default width to be erased as a border. The table below shows the measurement ranges that can be set. Input units Range Inch 0 to 2" (in 0.01" increments) Metric 0 mm to 50 mm (in 1 mm increments) NOTE: Refer to page 4-17 and page 5-23 for Border Erase. Use the procedure below to set the default border erase width. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Press [+] or [–] for the Border and Gutter width to erase. ], [Next] of Function Defaults, [ ] and then [Change] of Border Erase Default. You can use the numeric keys to enter the number directly. 4 Press [OK]. Border Erase to Back Page Select the Border Erase Method for Back Page of a sheet. The table below shows the available settings. Item 8-20 Description Same as Front Page Border Erase performed in the same setting as the front page Do Not Erase No Border Erase performed on the back page OPERATION GUIDE Default Setting (System Menu) NOTE: Refer to page 4-17 and page 5-23 for Border Erase. Use the procedure below to specify the border erase setting for the back of the page. 1 Press the System Menu key. 2 Press [Common Settings], [ Page. 3 Press [Same as Front Page] or [Do Not Erase]. 4 Press [OK]. ], [Next] of Function Defaults, [ ] and then [Change] of Border Erase to Back Margin Default Set the default margin. The table below shows the measurement ranges that can be set. Input units Range Inch -0.75 to 0.75" (in 0.01" increments) Metric -18 mm to 18 mm (in 1 mm increments) 8 Use the procedure below to set the default margin width. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Use the [+] or [-] to enter the margin widths for Left/Right and Top/Bottom. ], [Next] of Function Defaults, [ ] and then [Change] of Margin Default. You can use the numeric keys to enter the number directly. 4 Press [OK]. Auto Image Rotation Select the default Auto Image Rotation setting. The table below shows the available settings. Item Description Off No Auto Image Rotation performed. On Auto Image Rotation performed. NOTE: Refer to page 4-32 for Auto Image Rotation. Use the procedure below to set the default Auto Image Rotation settings. 1 Press the System Menu key. 2 Press [Common Settings], [ OPERATION GUIDE ], [Next] of Function Defaults, [ ] and then [Change] of Auto Image Rotation. 8-21 Default Setting (System Menu) 3 Select the default for [Off] or [On]. 4 Press [OK]. EcoPrint Select the EcoPrint default. The table below shows the available settings. Item Description Off No EcoPrint performed. On EcoPrint performed. NOTE: Refer to page 4-13 for EcoPrint. Use the procedure below to set the default EcoPrint setting. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select [Off] or [On] for the default. 4 Press [OK]. ], [Next] of Function Defaults, [ ] twice, and then [Change] of EcoPrint. PDF/TIFF/JPEG Image Select the default PDF/TIFF/JPEG file quality. Five options are available from 1 Low Quality (High Comp.) to 5 High Quality (Low Comp.). NOTE: Higher quality will make the stored files larger. Refer to page 5-12 for file formats. Use the procedure below to select the default file quality setting. 1 Press the System Menu key. 2 Press [Common Settings], [ TIFF/JPEG Image. 3 Select the default image quality from [1] (Low Quality) to [5] (High Quality). 4 Press [OK]. 8-22 ] and [Next] of Function Defaults. Press [ ] twice and then [Change] of PDF/ OPERATION GUIDE Default Setting (System Menu) High Comp. PDF Image Select the default quality setting for high compressed PDF files. The table below shows the available settings. Item Description Compression Ratio Priority Compression Ratio is given priority with smaller file size. Standard Standard quality Quality Priority Image quality is given priority with larger file size. Use the procedure below to select the default quality setting for highly compressed PDF files. 1 Press the System Menu key. 2 Press [Common Settings], [ Comp. PDF Image. 3 Select the default for [Compression Ratio Priority], [Standard], or [Quality Priority]. 4 Press [OK]. ] and [Next] of Function Defaults. Press [ ] twice and [Change] of High 8 Color TIFF Compression Settings Select the compression method for TIFF images handled on this machine. Use the procedure below to set the default Color TIFF Compression setting. 1 Press the System Menu key. 2 Press [Common Settings], [ TIFF Compression. 3 Select [TIFF V6] or [TTN2]. 4 Press [OK]. ] and [Next] of Function Defaults. Press [ ] twice and then [Change] of Color Repeat Copying Select the Repeat Copy default. The options are as follows. The table below shows the available settings. Item Description Off No Repeat Copy is performed. On Repeat Copy is performed. NOTE: This setting is not displayed when the optional Data Security Kit is installed or the Repeat Copy job is set to 0. Refer to page 4-36 for Repeat Copy. OPERATION GUIDE 8-23 Default Setting (System Menu) Use the procedure below to set the default Repeat Copy setting. 1 Press the System Menu key. 2 Press [Common Settings], [ Copy. 3 Select the default for [Off] or [On]. 4 Press [OK]. ] and [Next] of Function Defaults. Press [ ] twice and [Change] of Repeat Collate/Offset Set the defaults for Collate/Offset. The table below shows the available settings. Item Collate Offset Description Off Collate not performed. On Collate performed. Off Offset not performed. Each Set (Each Page) Offset performed. (If [Off] is selected of Collate, it is performed [Each Page].) NOTE: Refer to page 3-13 for Collate/Offset. Use the procedure below to set the default Collate/Offset settings. 1 Press the System Menu key. 2 Press [Common Settings], [ 3 Select the defaults for Collate and Offset respectively. 4 Press [OK]. ], [Next] of Function Defaults. Press [ ] twice and [Change] of Collate/Offset. JPEG/TIFF Print Select the image size (resolution) when printing JPEG or TIFF file. The table below shows the available settings. Item 8-24 Description Fit to Paper Size Fit the image size to the selected paper size. Image Resolution Print at resolution of the actual image. Fit to Print Resolution Fit the image size to the print resolution. OPERATION GUIDE Default Setting (System Menu) Use the procedure below to set the default JPEG/TIFF Print settings. 1 Press the System Menu key. 2 Press [Common Settings], [ Print. 3 Select the default for [Fit to Paper Size], [Image Resolution], or [Fit to Print Resolution]. 4 Press [OK]. ], [Next] of Function Defaults. Press [ ] twice and [Change] of JPEG/TIFF XPS Fit to Page Reduces or enlarges the image size to fit to the selected paper size when printing XPS file. Use the procedure below to set the default XPS Fit to Page settings. 1 Press the System Menu key. 2 Press [Common Settings], [ Page. 3 Select [Off] or [On] for the default. 4 Press [OK]. OPERATION GUIDE ], [Next] of Function Defaults. Press [ ] twice and [Change] of XPS Fit to 8 8-25 Default Setting (System Menu) Copy Settings The following settings are available for copying functions. • Paper Selection …8-26 • Auto Paper Selection …8-26 • Auto % Priority …8-27 • Reserve Next Priority …8-27 • Preset Limit …8-27 • Quick Setup Registration …8-28 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Paper Selection Set the default paper selection. The table below shows the available settings. Item Description Auto Automatically select the cassette containing paper in the same size as originals. Default Paper Source Select paper source set by Default Paper Source (refer to page 8-9). Use the procedure below to set the default paper selection. 1 Press the System Menu key. 2 Press [Copy] and [Change] of Paper Selection. 3 Press [Auto] or [Default Paper Source]. 4 Press [OK]. 5 Move to the copy screen and press the Reset key. Auto Paper Selection If [Auto] is selected for Paper Selection, set the paper size selection method when the zoom changes. The table below shows the available settings. Item 8-26 Description Most Suitable Size Select paper based on the current zoom and the size of the original. Same as Original Size Select paper that matches the size of the original, regardless the zoom. OPERATION GUIDE Default Setting (System Menu) Use the procedure below to specify the action performed for Auto Paper Selection. 1 Press the System Menu key. 2 Press [Copy] and [Change] of Auto Paper Selection. 3 Press [Most Suitable Size] or [Same as Original Size]. 4 Press [OK]. 5 Move to the copy screen and press the Reset key. Auto % Priority When a paper source of different size from the original is selected, select whether automatic zoom (reduce/ zoom) is performed. The table below shows the available settings. Item Description Off No zoom performed (copied in original size). On Automatic zoom performed as appropriate. 8 Use the procedure below to specify the automatic zoom priority. 1 Press the System Menu key. 2 Press [Copy] and [Change] of Auto % Priority. 3 Select the default for [Off] or [On]. 4 Press [OK]. 5 Move to the copy screen and press the Reset key. Reserve Next Priority Select the operation of the reserve copy and interrupt copy functions and for canceling jobs. Use the procedure below to select the default Reserve Next Priority setting. 1 Press the System Menu key. 2 Press [Copy] and [Change] of Reserve Next Priority. 3 Select the default for [Off] or [On]. 4 Press [OK]. Preset Limit Restrict the number of copies that can be made at one time. Options are 1-999 copies. Use the procedure below to set the limit on the number of copies. 1 Press the System Menu key. OPERATION GUIDE 8-27 Default Setting (System Menu) 2 Press [Copy] and [Change] of Preset Limit. 3 Press [+] or [–] or use the numeric keys to enter the limit for the number of copies. 4 Press [OK]. Quick Setup Registration Select the copying functions to be registered for Quick Setup. Six keys of the Quick Setup screen are allocated to typical functions but can be changed as necessary. Six items from the following options are available. Paper Selection, Zoom, Staple/Punch, Density, Duplex, Combine, Collate/Offset, Original Image, Original Size, Original Orientation, Continuous Scan NOTE: Refer to Quick Setup Screen on page 3-43 for the Quick Setup steps. Use the procedure below to register the Quick Setup functions. 1 Press the System Menu key. 2 Press [Copy] and [Next] of Quick Setup Registration. 3 Press [Change] of the function to be registered in Quick Setup. 4 Select a key (1-6) allocated on the Quick Setup Registration screen. Press [Off] to delete a key from the Quick Setup. 5 Press [OK]. If you overwrite the setting, a confirmation screen appears. Press [Yes]. 8-28 OPERATION GUIDE Default Setting (System Menu) Sending Settings The sending settings allow you to specify the following sending function options. • Quick Setup Registration …8-29 • Destination Check before Send …8-30 • Color Type …8-30 • Entry Check for New Destination …8-31 • Setting the Default Send Screen …8-31 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Quick Setup Registration Select the sending functions to be registered for Quick Setup. Six keys of the Quick Setup screen are allocated to typical functions but can be changed as necessary. Six items in the following options are available. 8 Original Size, 2-sided/Book Original, Sending Size, Original Orientation, File Format, Density, Original Image, Scan Resolution, FAX TX Resolution, Color Selection, Zoom, Continuous Scan Use the procedure below to register the Quick Setup functions. 1 Press the System Menu key. 2 Press [Send] and [Next] of Quick Setup Registration. 3 Press [Change] of the function to be registered in Quick Setup. 4 Select a key (1-6) allocated on the Quick Setup Registration screen. Press [Off] to delete a key from the Quick Setup. 5 Press [OK]. If you overwrite the setting, a confirmation screen appears. Press [Yes]. OPERATION GUIDE 8-29 Default Setting (System Menu) Destination Check before Send When performing sending jobs, display the confirmation screen of destinations after pressing the Start key. The table below shows the available settings. Item Description Off Do not display the confirmation screen of destinations. On Display the confirmation screen of destinations. NOTE: Refer to Confirmation Screen of Destinations on page 3-29 for the Quick Setup steps. Use the procedure below to set the destination check before send. 1 Press the System Menu key. 2 Press [Send] and then [Change] of Dest. Check before Send. 3 Select [Off] or [On]. 4 Press [OK]. Color Type Set the color type when you send color documents. The table below shows the available settings. Item Description RGB Send color documents in RGB. sRGB Allows you to match the color space for machines that support sRGB. Selecting RGB displays the color profile values set on the machine. Use the procedure below to set the color type. 1 Press the System Menu key. 2 Press [Send] and then [Change] of Color Type. 3 Select [RGB] or [sRGB]. 4 Press [OK]. 8-30 OPERATION GUIDE Default Setting (System Menu) Entry Check for New Destination When adding new destination, display the entry check screen to check the entered destination. The table below shows the available settings. Item Description Off Do not display the entry check screen. On Display the entry check screen. Use the procedure below to set the destination check before send. 1 Press the System Menu key. 2 Press [Send] and then [Change] of Entry Check for New Dest. 3 Select [Off] or [On]. 4 Press [OK]. Setting the Default Send Screen 8 Use this procedure to set the default screen displayed when you press the Send key. The table below shows the available settings. Item Detail Destination Displays the destination screen when the Send key is pressed (screen for sending). Address Book Displays the address book when the Send key is pressed Use the procedure below to set the default send screen. 1 Press the System Menu key. 2 Press [Send] and then [Change] of Default Screen. 3 Press [Destination] or [Address Book]. 4 Press [OK]. OPERATION GUIDE 8-31 Default Setting (System Menu) Document Box Settings The following settings are available for Document Box. • Registering / Editing Box …8-32 • Default Setting …8-32 • Job Box …8-32 • Quick Setup Registration …8-32 Registering / Editing Box Creates a new box, edits a box, or checks details of a box in the custom box, or deletes a box from the custom box. For details, refer to Using a Custom Box on page 6-2. Default Setting Sets the time at which documents in the custom box are automatically deleted. For details, refer to Setting the document deletion time on page 6-3. Job Box The following three operations can be done. For details, refer to each page shown below. • Quick Copy/Proof and Hold Print Box (page 6-13) • Repeat Copy Box (page 6-15) • Deleting a Form Stored (page 6-18) Quick Setup Registration Select the Storing in Box, Sending from Box, Printing from Box functions to be registered for Quick Setup. Six keys of the Quick Setup screen are allocated to typical functions but can be changed as necessary. The options are as follows. Store File Quick Setup Color Selection, Storing Size, Density, 2-sided/Book Original, Resolution, Zoom, Original Orientation, Original Size, Original Image, Continuous Scan Print Quick Setup Paper Selection, Collate/Offset, Staple/Punch, Duplex, Combine, Delete after Printed Send Quick Setup Sending Size, FAX TX Resolution, File Format, Delete after Transmitted 8-32 OPERATION GUIDE Default Setting (System Menu) Use the procedure below to register the Quick Setup functions. 1 Press the System Menu key. 2 Press [Document Box/Removable Memory] and [Next] of Quick Setup Registration. 3 Press [Next] of Store File, Print, or Send. 4 Press [Change] of the function to be registered in Quick Setup. 5 Select a key (1-6) allocated on the Quick Setup screen. Press [Off] to delete a key from the Quick Setup. 6 Press [OK]. If you overwrite the setting, a confirmation screen appears. Press [Yes]. 8 OPERATION GUIDE 8-33 Default Setting (System Menu) Printer Settings Printing from computers, settings are generally made on the application software screen. However, the following settings are available for configuring the defaults to customize the machine. • Emulation …8-34 • EcoPrint …8-35 • Override A4/Letter …8-35 • Duplex …8-36 • Copies …8-36 • Orientation …8-37 • Form Feed Timeout …8-37 • LF Action …8-37 • CR Action …8-38 • Paper Feed Mode …8-38 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Emulation Select the emulation for operating this machine by commands oriented to other types of printers. Selection of emulation The printer can emulate PCL 6, KPDL and KPDL(Auto). Use the procedure below to select the emulation. 1 Press the System Menu Key. 2 Press [Printer] > [Change] of Emulation. 3 Select the desired emulation. NOTE: If you selected [KPDL(Auto)], set Alternative Emulation, too. (Refer to page 8-34) When you have selected [KPDL] or [KPDL(Auto)], set KPDL Error Report, too. (Refer to page 8-35) 4 Press [OK]. Setting of Alternative Emulation When you have selected [KPDL(Auto)] as emulation mode, you can switch between KPDL and another emulation mode (alternative emulation) automatically according to the data to print. The alternative emulation you can set is [PCL6]. Use the procedure below to select the alternative emulation. 1 Press the System Menu Key. 8-34 OPERATION GUIDE Default Setting (System Menu) 2 Press [Printer] > [Change] of Emulation > [KPDL(Auto)] > [Alt Emulation]. 3 Select the desired alternative emulation and then press [OK]. 4 Press [OK]. Setting of KPDL error report When an error has occurred during printing in KPDL emulation mode, set whether or not the error report is output. The default setting is Off (not output). Use the procedure below to specify the KPDL error report setting. 1 Press the System Menu Key. 2 Press [Printer] > [Change] of Emulation > [KPDL] or [KPDL(Auto)] > [KPDL Error Report]. 3 Press [On] or [Off] and then press [OK]. 4 Press [OK]. EcoPrint EcoPrint conserves toner when printing. This is recommended for test copies where faded printing is not a problem. Use the procedure below to specify the EcoPrint setting. 1 Press the System Menu key. 2 Press [Printer] and [Change] of EcoPrint. 3 Press [Off] or [On]. 4 Press [OK]. Override A4/Letter Select whether to treat A4 size and Letter, which are similar in size, as the same size when printing. The table below shows the available settings. Item Description On A4 and Letter are regarded as the same in size. The machine will use whichever size is in the paper source. Off A4 and Letter are not regarded as the same in size. Use the procedure below to specify the override A4/Letter setting. 1 Press the System Menu key. 2 Press [Printer] and [Change] of Override A4/Letter. 3 Press [Off] or [On]. 4 Press [OK]. OPERATION GUIDE 8-35 8 Default Setting (System Menu) Duplex Select binding orientation for duplex mode. The table below shows the available settings. Item Description 1-sided No duplex mode 2-sided Bind ShortEdge Shorter edge bound 2-sided Bind LongEdge Longer edge bound Finish Use the procedure below to select a duplex setting. 1 Press the System Menu key. 2 Press [Printer] and [Change] of Duplex. 3 Press [1-sided], [2-sided Bind LongEdge], or [2-sided Bind ShortEdge]. 4 Press [OK]. Copies Set the default number of copies, from 1 to 999. Use the procedure below to specify the default number of copies. 1 Press the System Menu key. 2 Press [Printer] and [Change] of Copies. 3 Press [+],[–] or the numeric keys to set the default number of copies. 4 Press [OK]. 8-36 OPERATION GUIDE Default Setting (System Menu) Orientation Set the default orientation, Portrait or Landscape. Portrait Landscape Printer Printer Use the procedure below to set the default orientation for printing. 1 Press the System Menu key. 2 Press [Printer] and [Change] of Orientation. 3 Press [Portrait] or [Landscape]. 4 Press [OK]. 8 Form Feed Timeout Receiving print data from the computer, the machine may sometimes wait if there is no information signaling that the last page does not have any more data to be printed. When the preset timeout passes, the machine automatically prints paper. The options are between 5 and 495 seconds. Use the procedure below to set the form feed timeout. 1 Press the System Menu key. 2 Press [Printer], [ 3 Press [+] or [–] to set the Form Feed Timeout. ] and [Change] of Form Feed Timeout. You can set the timeout delay in seconds. You cannot use the numeric keys to enter this value. 4 Press [OK]. LF Action Set the line feed action when the machine receives the line feed code (character code 0AH). The table below shows the available settings. Item Description LF Only Only line feed performed. LF and CR Line feed and character return performed. Ignore LF No line feed performed. OPERATION GUIDE 8-37 Default Setting (System Menu) Use the procedure below to specify an LF action. 1 Press the System Menu key. 2 Press [Printer], [ 3 Press [LF Only], [LF and CR] or [Ignore LF]. 4 Press [OK]. ] and [Change] of LF Action. CR Action Set the character return action when the machine receives the character return code (character code 0DH). The table below shows the available settings. Item Description CR Only Only character return performed. LF and CR Character return and line feed performed. Ignore CR No character return performed. Use the procedure below to specify a CR action. 1 Press the System Menu key. 2 Press [Printer], [ 3 Press [CR Only], [LF and CR] or [Ignore CR]. 4 Press [OK]. ] and [Change] of CR Action. Paper Feed Mode While printing from the computer, select how to feed paper when the paper source and type are specified. The table below shows the available settings. Item Description Auto Search the paper source that matches the selected paper size and type. Fixed Print on paper loaded in the specified paper source. Use the procedure below to select the paper feed mode. 1 Press the System Menu key. 2 Press [Printer], [ 3 Press [Auto] or [Fixed]. 4 Press [OK]. 8-38 ] and [Change] of Paper Feed Mode. OPERATION GUIDE Default Setting (System Menu) Printing Reports/Sending Notice Print reports to check the machine settings and status. Default settings for printing the result reports can also be configured. NOTE: If user login administration is enabled, you can only print by logging in with administrator privileges. Printing Reports Printable reports are as follows. Status Page Check the information including current settings, available memory space, and optional equipment installed. Status Page xxxxx Firmware Version 8 Font List Check the font samples installed in the machine. OPERATION GUIDE 8-39 Default Setting (System Menu) Network Status Page Check the information including network interface firmware version, network address and protocol. Network Status Page xxxxx Firmware Version Service Status Page More detailed information is available than on the Status Page. Service personnel usually print the service status pages for maintenance purpose. Use the procedure below to print a report. 1 Press the System Menu key. 2 Press [Report] and [Next] of Print Report. 3 Press [Print] for the report you want to print. Printing starts. A confirmation screen appears. Press [Yes]. Send Result Report Automatically print a report of transmission result when a transmission is complete. The table below shows the available settings. Item Description Off No result report printed. On Result report automatically printed. Transmitted images can also be attached to the FAX result report. Error Only Result report printed only when a transmission ends in an error. If two or more destinations are registered, the reports are printed only for the destinations with the errors. Transmitted images can also be attached to the FAX result report. 1 Press the System Menu key. 2 Press [Report], [Next] of Result Report Setting, [Next] of Send Result Report and then [Change] of E-mail/ Folder. 3 Press [Off], [On], or [Error Only]. 4 Press [OK]. 8-40 OPERATION GUIDE Default Setting (System Menu) Report for Job Canceled before Sending Print a send result report when the job is canceled before being sent. 1 Press the System Menu key. 2 Press [Report], [Next] of Result Report Setting, [Next] of Send Result Report and then [Change] of Canceled before Sending. 3 Press [Off], [On]. 4 Press [OK]. 8 OPERATION GUIDE 8-41 Default Setting (System Menu) Adjustment/Maintenance Adjust printing quality and conduct machine maintenance. • Copy Density Adjustment …8-42 • Send/Box Density Adjust …8-42 • Print Density …8-43 • Drum Refresh …8-43 • Correcting Fine Black Lines …8-44 • System Initialization …8-44 • Display Brightness …8-44 • Silent Mode …8-45 • Charger Auto Cleaning …8-45 • Auto Color Correction...8-45 • Gray Adjustment...8-46 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Copy Density Adjustment Adjust copy density. Adjustment can be made in 7 levels both in auto and manual density modes. Use the procedure below to adjust the copy density. 1 Press the System Menu key. 2 Press [ 3 Press [Change] of Auto or of Manual. 4 Press [-3] - [+3] (Lighter-Darker) to adjust density. 5 Press [OK]. ], [Adjustment/Maintenance] and then [Next] of Copy Density Adjustment. Send/Box Density Adjust Adjust scan density when sending or storing the data in Document Box. Adjustment can be made in 7 levels both in auto and manual density modes. Use the procedure below to adjust the density. 1 Press the System Menu key. 2 Press [ 3 Press [Change] of Auto or of Manual. 4 Press [-3] - [+3] (Lighter-Darker) to adjust density. 5 Press [OK]. 8-42 ], [Adjustment/Maintenance] and then [Next] of Send/Box Density Adjust.. OPERATION GUIDE Default Setting (System Menu) Print Density Adjust print density. Adjustment can be made in 5 levels. Use the procedure below to adjust the print density. 1 Press the System Menu key. 2 Press [ 3 Press [1] - [5] (Lighter-Darker) to adjust density. 4 Press [OK]. ], [Adjustment/Maintenance] and then [Change] of Print Density. Drum Refresh Refresh the drum when image blur or white spots appear on images in copies. NOTE: Drum Refresh cannot be performed while printing. Execute Drum Refresh after the printing is done. To use [Drum Refresh], load Ledger or A3 size paper into the Multi Purpose tray. Use the procedure below to refresh the drum. 1 Press the System Menu key. 2 Press [ 3 Press [Next] of Drum Refresh. 4 Press [Execute] to perform Drum Refresh. 5 After Drum Refresh is completed, press [OK] to return to the Adjustment/Maintenance screen. 8 ], [Adjustment/Maintenance]. OPERATION GUIDE 8-43 Default Setting (System Menu) Correcting Fine Black Lines Correct fine black lines (black streaks caused by contamination), which may appear on the copies, when the optional document processor used. Paper feed direction The table below shows the available settings. Item Description Off No correction performed. On(Low) Correction performed. The reproduction of the image becomes lower when using Off. On(High) Correction performed. Select this item if black streak remains after using On (Low). The reproduction of the image becomes lower when using On (Low). NOTE: Using Correcting Fine Black Line can impair reproduction of fine characters. It is recommended to keep the default ([Off]). Use the procedure below to specify the setting for correcting fine black lines. 1 Press the System Menu key. 2 Press [ 3 Press [Off], [On(Low)] or [On(High)]. 4 Press [OK]. ], [Adjustment/Maintenance] and then [Change] of Correcting Black Line. System Initialization Initialize the hard disk mounted on the machine to return to the default mode. Refer to System Initialization on page 8-63 about the initialization procedures. Display Brightness Set the brightness of the touch panel. Use the procedure below to adjust the display brightness. 1 Press the System Menu key. 8-44 OPERATION GUIDE Default Setting (System Menu) 2 Press [ 3 Press [1] - [4] (Darker- Lighter) to adjust brightness. 4 Press [OK]. ], [Adjustment/Maintenance] and then [Change] of Display Brightness. Silent Mode Make the machine run more quietly. Select this mode when the running noise is uncomfortable. Use the procedure below to set Silent mode. 1 Press the System Menu key. 2 Press [ 3 Press [Off] or [On]. 4 Press [OK]. ], [Adjustment/Maintenance] and then [Change] of Silent Mode. Charger Auto Cleaning If black streaks appear on the printouts or scanned data, perform automatic cleaning of the main chargers. If no black line appears at the ends of the paper (margin), refer to Correcting Fine Black Lines on page 8-44. 1 Press the System Menu key. 2 Press [ 3 Press [Yes]. Automatic cleaning of the main charger starts and ends in about 45 seconds. 4 Once the cleaning ends, return to the Adjustment/Maintenance screen. ], [Adjustment/Maintenance] and then [Change] of Charger Auto Cleaning. Auto Color Correction This setting allows you to adjust the detection level used by the machine to determine whether the original is color or black and white during Auto Color Mode. Setting a lower value will result in more originals being identified as color, while a larger value will tend to increase the number of originals being identified as black and white. Use the procedure below to set the Auto Color Detection Level. 1 Press the System Menu key. 2 Press [ 3 Press one of keys [1] to [5] (Color - B & W) to set the detection level. 4 Press [OK]. ], [Adjustment/Maintenance], [ OPERATION GUIDE ] and then [Change] of Auto Color Correction. 8-45 8 Default Setting (System Menu) Gray Adjustment After prolonged use, or from the effects of surrounding temperature or humidity, the hue of printed color output may shift or color drift may occur. Use this function to correct color settings when the color of a finished copy does not match the original. NOTE: To perform gray adjustment, verify that either 11 × 8 1/2" or A4 paper is loaded into a cassette. Use the procedure below for adjustment. 8-46 1 Press the System Menu key. 2 Press [ ], [Adjustment/Maintenance], [ then [Next] of Gray Adjustment. 3 Press [Execute]. A color pattern is printed. 4 As shown in the illustration, place the printed side down on the platen with the three black boxes aligned to the top. 5 Press [Execute]. The color pattern is read and adjustment begins. 6 Press [OK] in the adjustment end confirmation screen. ] and OPERATION GUIDE Default Setting (System Menu) Date/Timer Date/Timer settings include: • Date/Time …8-47 • Date Format …8-47 • Time Zone …8-48 • Auto Panel Reset …8-48 • Auto Sleep …8-49 • Auto Error Clear …8-49 • Interrupt Clear Timer …8-50 NOTE: If user login administration is enabled, you can only change the settings by logging in with administrator privileges. Date/Time Set the date and time for the location where you use the machine. If you perform Send as E-mail, the date and time set here will be displayed on the header. CAUTION: Be sure to set Time Zone before the Date/Time setup. Use the procedure below to set the date and time. 1 Press the System Menu key. 2 Press [ 3 Press [+] or [–] to enter the date and time respectively. 4 Press [OK]. ], [Date/Timer] and then [Change] of Date/Time. NOTE: If you try to change the date/time when a trial application (page 8-75) is running, the If you change Date/Time setting, trial functions will be unavailable. Are you sure? message is displayed. To change the date/ time, press [Yes]. Date Format Select the display format of year, month, and date. The year is displayed in Western notation. Use the procedure below to select the date format. 1 Press the System Menu key. 2 Press [ 3 Select [MM/DD/YYYY], [DD/MM/YYYY], or [YYYY/MM/DD] and press [OK]. ], [Date/Timer] and then [Change] of Date Format. OPERATION GUIDE 8-47 8 Default Setting (System Menu) Time Zone Set the time difference in the location you are from GMT. Use the procedure below to set the time difference. 1 Press the System Menu key. 2 Press [ 3 Select the location. ], [Date/Timer] and then [Change] of Time Zone. NOTE: Press [ 4 ] or [ ] to select the location. Press [Off] or [On] of Summer Time and press [OK]. NOTE: If you select a region that does not utilize summer time, the summer time setting screen will not appear. Auto Panel Reset If no jobs are run for a certain period of time, automatically reset settings and return to the default setting. NOTE: Refer to page 8-15 for the default settings. Auto Panel Reset ON/OFF Select to use Auto Panel Reset or not. Use the procedure below to specify the auto panel reset setting. 1 Press the System Menu key. 2 Press [ 3 Press [Off] or [On]. 4 Press [OK]. ], [Date/Timer] and then [Change] of Auto Panel Reset. Panel Reset Timer If you select [On] for Auto Panel Reset, set the amount of time to wait before Auto Panel Reset. Options are between 5 and 495 seconds (every five seconds). NOTE: If you select [Off] for Auto Panel Reset, the time display does not appear. Use the procedure below to set the reset time. 1 Press the System Menu key. 2 Press [ 8-48 ], [Date/Timer] and then [Change] of Panel Reset Timer. OPERATION GUIDE Default Setting (System Menu) 3 Press [+] or [–] to enter the time until Auto Panel Reset is turned on. You cannot use the numeric keys to enter this value. 4 Press [OK]. Auto Sleep If no job runs for a certain period of time, automatically enter Sleep Mode. Refer to Sleep and Auto Sleep on page 2-9 for Sleep. Sleep Timer Set the amount of time to wait before Auto Sleep. Options are between 1 and 240 minutes (every one minute). Use the procedure below to set the Auto Sleep time. 1 Press the System Menu key. 2 Press [ 3 Press [+] and [–] or the numeric keys to enter the time until Auto Sleep is turned on. 4 Press [OK]. ], [Date/Timer] and then [Change] of Sleep Timer. 8 Auto Error Clear If an error occurs during printing, the print job stops to wait for the next step to be taken by the user. In the Auto Error Clear mode, automatically clear the error after a set amount of time elapses. The following errors are automatically cleared. Print overrun Memory is full Auto Error Clear ON/OFF Select whether to use Auto Error Clear or not. Use the procedure below to specify the auto error clear setting. 1 Press the System Menu key. 2 Press [ 3 Press [Off] or [On]. 4 Press [OK]. ], [Date/Timer] and then [Change] of Auto Error Clear. Error Clear Timer If you select [On] for Auto Error Clear, set the amount of time to wait before automatically clearing errors. Options are between 5 and 495 seconds (every five seconds). NOTE: If you select [Off] for Auto Error Clear, the time display does not appear. OPERATION GUIDE 8-49 Default Setting (System Menu) Use the procedure below to set the automatic error clear delay. 1 Press the System Menu key. 2 Press [ 3 Press [+] or [–] to enter the time until printing restarts. ], [Date/Timer], [ ] and then [Change] of Error Clear Timer. You cannot use the numeric keys to enter this value. 4 Press [OK]. Interrupt Clear Timer Set the period after which the machine reverts to Normal mode when it has been set to Interrupt Copy mode and then left unused. Any period between 5 and 495 seconds (in five-second increments) can be set. The procedure for setting the interrupt clear timer is explained below. 1 Press the System Menu key. 2 Press [ 3 Press [+] or [-] to enter the time for the interrupt clear timer. 4 Press [OK]. 8-50 ], [Date/Timer], [ ] and then [Change] of Interrupt Clear Timer. OPERATION GUIDE Default Setting (System Menu) Editing Destination (Address Book/Adding One Touch Keys) Save frequently used destinations to Address Book or One Touch Keys. The saved destinations can be changed. The destinations are available for Send as E-mail, Send to Folder, and Fax Transmission (optional). Adding a Destination Add a new destination to the Address Book. There are two registering methods, contacts and groups. When adding a group, enter the group name and select group members from the Address Book. NOTE: If user login administration is enabled, you can only edit destinations in the Address Book by logging in with administrator privileges. Adding a contact A maximum of 1,000 contact addresses can be registered. Each address can include the information such as destination name, E-mail address, FTP server folder path, computer folder path, and FAX No. (optional). Use the procedure below to register a new individual contact. 1 Press the System Menu key. 2 Press [Edit Destination], [Register/Edit] of Address Book, [Add], [Contact] and then [Next]. 3 To specify the address number, press [Change] in Address Number. 4 Press [+],[–] or numeric keys to enter a particular Address Number (1-2500). 8 To have the number assigned automatically, enter “0000”. NOTE: Address Number is an ID for a destination. You can select any available number out of 2,500 numbers for contacts and 500 numbers for groups. If you specify an address number that is already in use, an error message appears when you press [Register] and the number cannot be registered. If you set “0000” as the address number, the address is registered under the lowest available number. 5 Press [OK]. The screen shown in step 3 reappears. 6 Press [Change] of Name. 7 Enter the destination name (up to 32 characters) to be displayed on the Address Book and press [OK]. The screen shown in step 3 reappears. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 8 Press [E-mail] to add an e-mail address, [SMB] to add a folder on the computer, or [FTP] to add an FTP folder. The procedure differs depending on the transmission method selected. OPERATION GUIDE 8-51 Default Setting (System Menu) E-mail Address Press [Change] of E-mail Address, enter the E-mail address and press [OK].The table below explains the items to be entered. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. The Folder (FTP) Address Press [Change] of Host Name, Path, Login User Name and Login Password, enter the information for each item and press [OK]. The table below explains the items to be entered. Max. No. of Characters Item Description Host Name* FTP server host name or IP address 64 chars Path Path for the file to be stored (e.g., "\User\ScanData") If no path is entered, the file is stored in the home directory. 128 chars Login User Name User name FTP server login 64 chars Login Password Password for FTP server login 64 chars * If you specify a port number other than the default (21), use the "Host name: port number" format. (e.g., FTPhostname:140) To enter the IPv6 address, enclose the address in brackets [ ]. (e.g., [3ae3:9a0:cd05:b1d2:28a:1fc0:a1:10ae]:140) NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. Press [Connection Test] to check the connection to the FTP server you chose. If the connection fails, check the entries you made. 8-52 OPERATION GUIDE Default Setting (System Menu) The Folder (SMB) Address Press [Change] of Host Name, Path, Login User Name and Login Password, enter the information for each item and press [OK]. The table below explains the items to be entered. Item Description Max. No. of Characters Host Name* Host name or IP address of the sending computer 64 chars Path Path to the folder used to save files (e.g., “\User\ScanData”) 128 chars Login User Name User name for folder access For example, abcdnet\james.smith 64 chars Login Password Password for folder access 64 chars * If you specify a port number other than the default (139), use the “Host name: port number” format. (e.g., SMBhostname:140) To enter the IPv6 address, enclose the address in brackets [ ]. (e.g., [3ae3:9a0:cd05:b1d2:28a:1fc0:a1:10ae]:140) 8 NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. Press [Connection Test] to check the connection to the computer you chose. If the connection fails, check the entries you made. 9 Check if the destination entry is correct and press [Register]. The destination is added to the Address Book. Adding a Group Compile two or more contacts into a group. Designations in the group can be added at the same time. When adding a group, a maximum of 500 groups can be added in the Address Book. NOTE: Before adding a group in the Address Book, the contacts to be included in the group must be added first. Up to 100 destinations for the e-mail, 500 destinations for the FAX, and the total of 10 destinations for the FTP and SMB can be registered per a group. Use the procedure below to register a group. 1 Press the System Menu key. 2 Press [Edit Destination], [Register/Edit] of Address Book, [Add], [Group] and then [Next]. 3 To specify the address number, press [Change] in Address Number. OPERATION GUIDE 8-53 Default Setting (System Menu) 4 Use [+]/[-] or the numeric keys to enter an address number (1 to 2500). To have the number assigned automatically, set "0000". NOTE: Address Number is an ID for a group. You can select any available number out of 2,000 numbers for contacts and 500 numbers for groups. If you specify an address number that is already in use, an error message appears when you press [Register] and the number cannot be registered. If you set "0000" as the address number, the address is registered under the lowest available number. 5 Press [OK]. The Add Group screen reappears. 6 Press [Change] of Name. 7 Enter the group name displayed on the Address Book not more than 32 characters. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 8 Press [Member]. 9 Press [Add]. 10 Select destinations (contacts) to add to the group. NOTE: Destinations can be sorted or searched by destination name or address number. Refer to Specifying Destination on page 3-30 for Address List. 11 Press [OK]. If you have more destinations to add, repeat Steps 9 to 11. 12 Check if the selected destination was added to the group and press [Register]. Now the group is added to the Address Book. Editing a Destination Edit/delete the destinations (Contacts) you added to the Address Book. Use the procedure below to edit a destination. 1 Press the System Menu key. 2 Press [Edit Destination] and then [Register/Edit] of Address Book. 3 Select a destination or group to edit. NOTE: Destinations can be sorted or searched by destination name or address number. Refer to Specifying Destination on page 3-30 for Address List. 4 Press [Detail]. The procedure differs depending on the details to be edited. 8-54 OPERATION GUIDE Default Setting (System Menu) Editing a Contact 1 Change Address Number, Name and destination type and address. Refer to Adding a contact on page 8-51 for the details. 2 After you have completed the changes, press [Register]. 3 Press [Yes] in the change confirmation screen to register the changed destination. Editing a Group 1 Change Address Number and Name. Refer to Adding a Group on page 8-53 for the details. 2 Press [Member]. 3 To delete any destination from the group, select the destination and press [Delete]. Press [Yes] on the screen to confirm the deletion. 4 After you have completed the changes, press [Register]. 5 Press [Yes] in the change confirmation screen to register the changed group. Deleting a Contact or Group Repeat Steps 1 to 3, press [Delete]. Press [Yes] on the screen to confirm the deletion. Deletion is performed. Adding a Destination on One Touch Key 8 Add a new destination (contact or group). A maximum of 1000 destinations can be registered. NOTE: Refer to Specifying Destination on page 3-30 for use of One Touch Key. Use the procedure below to register a new destination under a One Touch key. 1 Press the System Menu key. 2 Press [Edit Destination] and [Register/Edit] of One Touch Key. 3 Select a One Touch Key number (0001 to 1000) for the destination. Pressing Quick No. Search key or [No.] enables direct entry of a One Touch Key number. Select a One Touch Key with no registered destination. 4 Press [Register/Edit]. The address book appears. 5 Select a destination (contact or group) to add to the One Touch Key number. Pressing [Detail] shows the detailed information of the selected destination. NOTE: Destinations can be sorted or searched by destination name or address number. Refer to Specifying Destination on page 3-30 for Address List. 6 Press [OK]. The destination will be added to the One Touch Key. Editing One Touch Key Edit/delete the destinations you added to One Touch Key. OPERATION GUIDE 8-55 Default Setting (System Menu) Use the procedure below to edit the One Touch key. 1 Press the System Menu key. 2 Press [Edit Destination] and then [Register/Edit] of One Touch Key. 3 Select a One Touch Key number (0001 to 1000) for the destination. Pressing Quick No. Search key or [No.] enables direct entry of a One Touch Key number. The procedure differs depending on the details to be edited. Changing the Registered Information 1 Press [Register/Edit]. 2 Select a new destination (Contact or group). Pressing [Detail] shows the detailed information of the selected destination. NOTE: Destinations can be sorted or searched by destination name or address number. Refer to Specifying Destination on page 3-30 for Address List. 3 Press [OK]. 4 Press [Yes] on the screen to add the destination to the One Touch Key. Deleting the Registered Information 1 Press [Delete]. 2 Press [Yes] on the screen to confirm the deletion of the data registered in the One Touch Key. 8-56 OPERATION GUIDE Default Setting (System Menu) Sort Settings Select the default sort setting of the address for the address book. The table below shows the available settings. Item Detail No. Displays the destination list in order of the registered number. Name Displays the destination list in order of the registered name. Use the procedure below to specify the Sort settings. 1 Press the System Menu key. 2 Press [Edit Destination], [Next] of Address Book Defaults and then [Change] of Sort. 3 Select [No.] or [Name]. 4 Press [OK]. Narrow Down Settings This procedure can be used to filter (narrow down) the types of destination listed when the address book is displayed. The table below shows the available settings. Item Detail Off Displays all destination types in the destination list. E-mail Displays only e-mail destinations. Folder Displays only folder (SMB or FTP) destinations. FAX Displays only FAX destinations. i-FAX Displays only i-FAX destinations. Group Displays only groups. Use the procedure below to specify the Narrow Down settings. 1 Press the System Menu key. 2 Press [Edit Destination], [Next] of Address Book Defaults and then [Change] of Narrow Down. 3 Select the type of destination filter. 4 Press [OK]. OPERATION GUIDE 8-57 8 Default Setting (System Menu) Internet Browser Setup This procedure sets up the Internet browser application. You can specify the following Internet browser settings. • Internet Browser Setting • Browser Preferences • Proxy Settings Internet Browser Setting This selects whether or not the Internet browser is used. Use the procedure below to specify the Internet browser setting. 1 Press the System Menu key. 2 Press [ ] and then [Internet]. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Press [Change] of Internet Browser. 4 Press [On] or [Off]. 5 Press [OK]. Browser Preferences This specifies Internet browser preferences such as your home page setting and how pages are displayed. NOTE: This is not displayed if you selected Off in Internet Browser Setting (page 8-58). Use the procedure below to set your Internet browser preferences. 1 Press the System Menu key. 2 Press [ ] and then [Internet]. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Press [Next] of Browser Environment. 8-58 OPERATION GUIDE Default Setting (System Menu) 4 To set your home page, press [Change] of Home Page, press [URL], enter the URL and then press [OK]. Press [OK] again. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 5 To set the text size, press [Change] of Text Size, select [Large], [Medium] or [Small] as the text size and then press [OK]. 6 To set the display mode, press [Change] of Display Mode, select [Normal], [Just-Fit Rendering] or [SmartFit Rendering] as the display mode and then press [OK]. 7 To specify the settings for accepting cookies, press [Change] of Cookie, select [Accept All], [Reject All] or [Prompt before Accepting] as your cookie acceptance policy and then press [OK]. Proxy Settings Use the procedure below to specify the proxy settings. 1 Press the System Menu key. 2 Press [ ] and then [Internet]. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Press [Change] of Proxy and then press [On]. To set a proxy server (HTTP) 1 Press [Keyboard] of Proxy Server (HTTP), enter the proxy address and press [OK]. 2 Press [# Keys] and enter the port number. To set a proxy server (HTTPS) 1 Press [Keyboard] of Proxy Server (HTTPS), enter the proxy address and press [OK]. 2 Press [# Keys] and enter the port number. To set domains for which no proxy is used 1 Press [Keyboard] of Do Not Use Proxy for Following Domains, enter the domain name and press [OK]. NOTE: Refer to the Character Entry Method on Appendix-10<blue> for details on entering characters. 4 Press [OK]. OPERATION GUIDE 8-59 8 Default Setting (System Menu) Applications You can install and use applications that will make your day-to-day use of this machine more efficient. Installing Applications You can install new applications. Use the procedure below to install an application. 1 Insert the USB memory containing the application to be installed into the USB memory slot (A1). NOTE: If Removable Memory is recognized. Displaying files. appears, press [No]. 2 Press the System Menu key. 3 Press [ ] and then [Application]. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Add]. 5 Select the application to be installed and press [Install]. You can view detailed information on the selected application by pressing [Detail]. 6 When the confirmation screen appears, press [Yes]. Installation of the application begins. Depending on the application being installed, the installation may take some time. Once the installation ends, the original screen reappears. 7 To install another application, repeat steps 5 to 6. 8 To remove the USB memory, press [Remove Memory] and wait until the Removable Memory can be safely removed message appears. Then remove the USB memory. Activating/Deactivating Application To use an application, set the application to Activate. Use the procedure below to start using an application. 1 Press the System Menu key. 8-60 OPERATION GUIDE Default Setting (System Menu) 2 Press [ ] and then [Application]. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Select the desired application and press [Activate]. You can view detailed information on the selected application by pressing [Detail]. NOTE: To exit an application, press [Deactivate]. 4 Enter the license key and press [Official]. Some applications do not require you to enter a license key. If the license key entry screen does not appear, go to Step 5. To use the application as a trial, press [Trial] without entering the license key. 5 When the confirmation screen appears, press [Yes]. IMPORTANT: If you change the date/time while using an application, you will no longer be able to use the application. Launching Applications You can launch any application for which Activate is set. Use the procedure below to launch an application. 1 Press the Application key. A list of available applications appears on the touch panel. 2 Press the key for the application to be launched. The application starts up. 3 To exit the application, press [✕]. 4 When the application exit confirmation screen appears, press [Yes]. NOTE: The procedure for exiting some applications may differ. OPERATION GUIDE 8-61 8 Default Setting (System Menu) Deleting Applications Use the procedure below to delete an installed application. IMPORTANT: Always exit the application to be deleted before deleting the application. (Refer to Activating/ Deactivating Application on page 8-60.) 1 Press the System Menu key. 2 Press [ ] and then [Application]. NOTE: If login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Select the application to be deleted and press [Delete]. You can view detailed information on the selected application by pressing [Detail]. 4 When the deletion confirmation screen appears, press [Yes]. The application is deleted. 8-62 OPERATION GUIDE Default Setting (System Menu) System Initialization Initialize the hard disk mounted on the machine to return to the default mode. CAUTION: System initialization will erase Custom Document Boxes, data stored in Document Box, addresses in the Address Book, user property, account information, and settings. NOTE: This item will not be displayed if the optional Data Security Kit is installed. Refer to the Data Security Kit (E) Operation Guide on the bundled CD-ROM about the functions added when the Data Security Kit is installed and related procedures. Using Network Print Monitor allows you to back up addresses in the Address Book. 1 Press the System Menu key. 2 Press [ 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 When the confirmation screen appears, press [Yes]. ], [Adjustment/Maintenance] and then [Execute] of System Initialization. 8 Initialization starts. IMPORTANT: The Formatting... Do not turn off the main power switch. message appears during initialization. Wait until initialization ends. 5 Once the initialization ends, the message Task is completed. Turn the main power switch off and on. appears. Turn the main power switch off. Restarting the System Restart the CPU without turning the main power switch off. Use this to deal with any unstable operation by the machine. (Same as the computer restart.) Use the procedure below to restart the system. 1 Press the System Menu key. 2 Press [System] and [Execute] of Restart. NOTE: If user login administration is disabled, the user authentication screen appears. Enter a login user name and password, and press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 When the confirmation screen appears, press [Yes]. The system is restarted. OPERATION GUIDE 8-63 Default Setting (System Menu) Network Setup The following network settings are available. • Checking Host Name …8-64 • TCP/IP (IPv4) Setup …8-64 • TCP/IP (IPv6) Setup …8-64 • Protocol Detail …8-66 • NetWare Setup …8-67 • AppleTalk Setup …8-68 • WSD Scan Setup …8-68 • WSD Print Setup …8-68 • Secure Protocol …8-69 • IPSec Setting …8-71 • LAN Interface Setup …8-71 Checking Host Name Check the host name of the machine. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network. Check the host name displayed under Host Name. TCP/IP (IPv4) Setup Set up TCP/IP to connect to the Windows network. Refer to TCP/IP (IPv4) Setup (by Entering IP Addresses) on page 2-12 about the procedures. TCP/IP (IPv6) Setup Set up TCP/IP (IPv6) to connect to the network. The default settings are "TCP/IP Protocol: On, TCP/IP (IPv6): Off. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Change] of TCP/IP. 4 Press [On] and then press [OK]. 5 Press [Next] of IPv6. 6 Press [Change] of IPv6. 7 Press [On]. IP Address (Link Local) appears. 8 Press [OK]. 9 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. 8-64 OPERATION GUIDE Default Setting (System Menu) Manual Setting (IPv6) Manually specify the IP address, prefix length, and gateway address of TCP/IP (IPv6). The manual setting is available when selecting [On] for TCP/IP (IPv6). Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Next] of IPv6. 4 Press [Next] of Manual Setting. 5 Press [IP Address (Manual)] to enter IP address. The format of the IPv6 address is a sequence of numbers (128 bit in total) separated by colons, e.g. 2001:db8:3c4d:15::1a2c:1a1f. 6 Press [OK]. Press [# Keys] of Prefix Length (0 - 128) to enter the prefix length using the numeric keys. 7 Press [Default Gateway] to enter the default gateway. 8 Check that all the entries are correct and Press [OK]. 9 After changing the setting, restart the system or turn the machine OFF and then ON again. 8 For detailed information on restarting the system, refer to Restarting the System on page 8-63. RA (Stateless) Settings Select whether or not to use RA (Stateless). The RA (Stateless) settings are available when selecting [On] for TCP/IP (IPv6). The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Next] of IPv6. 4 Press [Change] of RA(Stateless). 5 Press [On] or [Off] of RA (Stateless). When selecting [On], IP Address 1 to 5 (Stateless) appears. 6 Press [OK]. 7 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. DHCP (IPv6) Settings Select whether or not to use the DHCP (IPv6) server. The DHCP (IPv6) Settings are available when selecting [On] for TCP/IP (IPv6). The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Next] of TCP/IP Setting. 3 Press [Next] of IPv6. OPERATION GUIDE 8-65 Default Setting (System Menu) 4 Press [Change] of DHCP. 5 Press [On] or [Off] of DHCP. When selecting [On], IP Address (Stateful) appears. 6 Press [OK]. 7 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. Protocol Detail The table below lists the network related function settings. The network related functions are available when TCP/IP is On. Item 8-66 Default Setting Description Restarting the System* NetBEUI Selects whether or not to receive documents using NetBEUI. On Y LPD Select whether or not to receive documents using LPD as the network protocol. On Y SMTP (E-mail TX) Select whether or not to send e-mail using SMTP. Off N POP3 (E-mail RX) Select whether or not to receive e-mail using POP3. Off N FTP Client (Transmission) Select whether or not to send documents using FTP. When selecting [On], set the FTP Port Number. Use the FTP default port 21. On Y FTP Server (Reception) Select whether or not to receive documents using FTP. On Y SMB Client (Transmission) Select whether or not to send documents using SMB. When selecting [On], set the SMB default Port Number. Use the SMB default port 139. For Windows Vista, use 445. On N i-FAX Select whether or not to use i-FAX. On N LDAP Select whether or not to use LDAP. Off N SNMP Select whether or not to communicate using SNMP. On Y SNMPv3 Select whether or not to communicate using SNMPv3. Off Y HTTP Select whether or not to communicate using HTTP. On Y Port:21 Port:139 OPERATION GUIDE Default Setting (System Menu) Item Default Setting Description Restarting the System* HTTPS Select whether or not to communicate using HTTPS. SSL must be set to [On] in SSL Setup on page 8-69. On Y IPP Select whether or not to communicate using IPP. When selecting [On], set the IPP default Port Number. Use the IPP default port 631. Off Y IPP over SSL Select whether or not to use IPP over SSL. SSL must be set to [On] in SSL Setup on page 8-69. Off Y Raw Port Select whether or not to receive documents using Raw Port. On Y * Port:631 Y: The machine must be restarted after the setting is changed. N: The machine does not need to be restarted after the setting is changed. 8 Use the procedure below. The following procedure is an example for specifying the SMTP (E-mail TX) settings. 1 Press the System Menu key. 2 Press [System] and then [Next] of Network to display the network settings screen. 3 Display the item you want to set and press [Change] for that item. In this example, press [Change] of SMTP (E-mail TX). 4 Press [On] or [Off]. 5 Press [OK]. 6 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. NetWare Setup Select the NetWare network connection. After that, select frame types for NetWare network from Auto, Ethernet-II, 802.3, 802.2, or SNAP. The default settings are "On, Frame Type: Auto". Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Change] of NetWare. 3 Press [On]. 4 Press the key for the frame type you want to use. OPERATION GUIDE 8-67 Default Setting (System Menu) 5 Press [OK]. 6 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. AppleTalk Setup Select the Apple Talk network connection. Refer to AppleTalk Setup on page 2-14 about the procedures. WSD Scan Setup Select whether or not to use WSD Scan. The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Change] of WSD Scan. 3 Press [On] or [Off]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. WSD Print Setup Select whether or not to use WSD Print. The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Change] of WSD Print. 3 Press [On] or [Off]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. 8-68 OPERATION GUIDE Default Setting (System Menu) Secure Protocol Encrypt the communication between your PC and the machine using the SSL encryption. After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. The following Secure Protocol settings are available. • SSL Setup …8-69 • IPP Security Setup …8-69 • HTTP Security Setup …8-69 • LDAP Security Setup …8-70 SSL Setup Select whether or not to use SSL. The default setting is On. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network, [Next] of Secure Protocol, and then [Next] of SSL. 3 Press [On] or [Off]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. 8 For detailed information on restarting the system, refer to Restarting the System on page 8-63. IPP Security Setup Select the IPP security level. This setup is available when SSL is On. The default setting is IPP over SSL Only. NOTE: IPP must be set to [On] in Protocol Detail on page 8-66. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network, [Next] of Secure Protocol, and then [Change] of IPP Security. 3 Press [IPP over SSL Only] or [IPP or IPP over SSL]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. HTTP Security Setup Select the HTTP security level. This setup is available when SSL is On. The default setting is HTTPS Only. OPERATION GUIDE 8-69 Default Setting (System Menu) NOTE: HTTP must be set to [On] in Protocol Detail on page 8-66. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network, [Next] of Secure Protocol, and then [Change] of HTTPS Security. 3 Press [HTTP or HTTPS] or [HTTPS Only]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. LDAP Security Setup Select the type of encryption according to the type of security employed by the LDAP server. This setup is available when SSL is On. The default setting is Off. NOTE: LDAP must be set to [On] in Protocol Detail on page 8-66. The table below shows the available settings. Item Description Off Do not use security employed by the LDAP server. LDAP over SSL Use implicit mode for data communication. The server provides services using the LDAP over SSL port (636). Encryption is applied to any data communication using this port. LDAPv3/TLS Use explicit mode for data communication. Select this if the server supports the start TLS command. This uses the same port (389) as LDAP. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network, [Next] of Secure Protocol, and then [Change] of LDAP Security. 3 Press [Off], [LDAP over SSL] or [LDAPv3/TLS]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. 8-70 OPERATION GUIDE Default Setting (System Menu) IPSec Setting Sets up IPSec. The default setting is Off. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network, and then [Change] of IPSec. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Press [On]. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. LAN Interface Setup Specify the settings for the LAN interface to be used. The default setting is Auto. Use the procedure below. 1 Press the System Menu key. 2 Press [System], [Next] of Network and then [Change] of LAN Interface. 3 Select [Auto], [10BASE-T Half], [10BASE-T Full], [100BASE-TX Half] or [100BASE-TX Full] as the LAN interface. 4 Press [OK]. 5 After changing the setting, restart the system or turn the machine OFF and then ON again. For detailed information on restarting the system, refer to Restarting the System on page 8-63. OPERATION GUIDE 8-71 8 Default Setting (System Menu) Interface Block Setting This allows you to protect this machine by blocking the interface with external devices such as USB hosts or optional interfaces. The following interface block settings are available: • USB Host (USB memory slot setting) • USB Device (USB interface setting) • Optional interface (Optional interface card setting) USB Host (USB memory slot setting) This locks and protects the USB memory slot (A1) or USB port (A2) (USB host). The default setting is Unblock. Use the procedure below to specify the USB Host setting. 1 Press the System Menu key. 2 Press [System], [Next] of Interface Block Setting and then [Change] of USB Host. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Press [Block]. 4 Press [OK]. USB Device (USB interface setting) This locks and protects the USB interface connector (B1) (USB Device). The default setting is Unblock. Use the procedure below to specify the USB Device setting. 1 Press the System Menu key. 2 Press [System], [Next] of Interface Block Setting and then [Change] of USB Device. 3 Press [Block]. 4 Press [OK]. Optional interface (Optional interface card setting) This locks and protects the optional interface slots (OPT1 or OPT2). The default setting is Unblock. Use the procedure below to specify the optional interface setting. 1 Press the System Menu key. 2 Press [System], [Next] of Interface Block Setting and then [Change] of Optional Interface 1 or Optional Interface 2. 3 Press [Block]. 4 Press [OK]. 8-72 OPERATION GUIDE Default Setting (System Menu) Security Level (Security Level setting) The Security Level setting is primarily a menu option used by service personnel for maintenance work. There is no need for customers to use this menu. Document Guard Setting When the optional Printed Document Guard Kit is installed, the machine prevents the unauthorized copying and/ or transmission of documents that contain important confidential or personal information. Use the Security Watermark of Advanced in KX DRIVER to embed the guard pattern in a document. (Refer to the Printer Driver User Guide for details.) We suggest you to confirm how the machine performs this function on your environment. Canceled. copy 8 send or fax Print the guard pattern using KX DRIVER. Machine Operation after Detecting the Document Guard Pattern Item Description Common operation Displays the message that indicates the machine detected the document guard pattern and stops scanning the remaining documents. Copy functions Prints the documents in blank from the position that the machine detected the document guard pattern. Document Box functions Does not store the documents in the hard disk Send functions Cancels the job.* FAX functions Does not send the documents. * Sends the documents that are scanned before the document guard pattern is detected if you have selected File Separation. If not, every documents will not to be sent. OPERATION GUIDE 8-73 Default Setting (System Menu) Limitations: - Scanning speed will be limited to the speed of scanning 600 dpi image. (Printing speed will not be limited.) - FAX transmission will be limited to the memory transmission. Note: - The Printed Document Guard Kit should not fully prevents a leak of information. We do not guarantee any loss incurred while using this feature or when malfunction occurred with this feature. - The guard pattern printed on the colored paper or paper that is decorated with special design may not be detected. - We do not guarantee the integrity of the detection. If the malfunction occurs, contact your service representative. Use the procedure below to specify the Document Guard setting. 1 Press the System Menu key. 2 Press [System] and then [Next] of Optional Function. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Select [Document Guard] from the list and then [Activate]. 4 Enter the license key and press [Official]. To use the function as a trial, press [Trial] without entering the license key. NOTE: For details on how to enter the license key, consult your dealer or service representative. 8-74 OPERATION GUIDE Default Setting (System Menu) Optional Functions You can use the optional applications installed on this machine. Overview of the Applications The applications listed below are installed on this machine. You can use these applications for a limited period on a trial basis. • Printed Document Guard Kit This prevents the unauthorized copying and/or transmission of documents that contain important confidential or personal information. When a document is printed from a computer, this feature imprints a special pattern on the document. When anyone attempts to copy or send that document on this machine, the machine detects the pattern and protects the information by printing the document in blank, prohibiting transmission. NOTE: Restrictions such as the number of times the application can be used during the trial period differ depending on the application. Starting Application Use 8 Use the procedure below to start using an application. 1 Press the System Menu key. 2 Press [System] and then [Next] of Optional Function. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Select the desired application and press [Activate]. You can view detailed information on the selected application by pressing [Detail]. 4 In the license key entry screen, press [Official]. Some applications do not require you to enter a license key. If the license key entry screen does not appear, go to Step 5. To use the application as a trial, press [Trial] without entering the license key. 5 When the confirmation screen appears, press [Yes]. IMPORTANT: If you change the date/time while using an application, you will no longer be able to use the application. OPERATION GUIDE 8-75 Default Setting (System Menu) Checking Application Details Use the procedure below to check the details of an application. 1 Press the System Menu key. 2 Press [System] and then [Next] of Optional Function. NOTE: If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 3 Select the application you want to check the details of and press [Detail]. You can now view detailed information on the selected application. 8-76 OPERATION GUIDE Default Setting (System Menu) Accessibility Display (Enlarged Touch Panel Display) Touch panel characters and key displays can be enlarged. Use the numeric keys to select items and proceed to the next screen. NOTE: Accessibility can be used only with Copying and Sending registered on the Quick Setup screen. To set functions other than those displayed in the accessibility screens, you must return to the original display. Press the Accessibility Display key again. Press the Accessibility Display key when in the Copy or Send (i.e. the Copy or Send key indicator is On). Ready to copy. Enlarged keys or characters appear on the touch panel. Copies Operation can also be made by pressing any numeric key corresponding to the number displayed. (e.g. Press the 2 key to adjust zoom.) Quantity Auto Paper Selection 2-sided >>2-sided Duplex 100% Zoom 2 in 1 Combine Status OPERATION GUIDE Normal 0 Density Follow the instructions on the screen for subsequent operations. Off Staple/Punch 08/08/2009 10:10 8-77 8 Default Setting (System Menu) 8-78 OPERATION GUIDE 9 Maintenance This chapter describes cleaning and toner replacement. • • Cleaning..............................................................................................9-2 Toner Container and Waste Toner Box Replacement .........................9-8 OPERATION GUIDE 9-1 Maintenance Cleaning Clean the machine regularly to ensure optimum output quality. CAUTION: For safety, always unplug the power cord before cleaning the machine. Original Cover / Glass Platen Wipe the backside of the original cover, the inside of the document processor and the glass platen with a soft cloth dampened with alcohol or mild detergent. IMPORTANT: Do not use thinner or other organic solvents. Original Cover Glass Platen 9-2 OPERATION GUIDE Maintenance Slit Glass/Dual scanning area If black streaks or dirt appears in copies when using the optional document processor, clean the slit glass with the supplied cleaning cloth. The message Clean the slit glass. may be displayed if the slit glass requires cleaning. Clean the slit glass. 1.Open the document processor. 2.Clean the surface of the slit glass located on the left side with the supplied dry cloth. 3.Close the document processor and press [End]. Note that dirty glass and sheet may cause black streaks to appear in the output. When using the document processor to allow dual scanning, clean the dual scanning unit also. 02/03 End Hold Status 08/08/2009 10:10 IMPORTANT: Wipe the slit glasses with the dry accessory cloth. Do not use water, soap or solvents for cleaning. 1 Remove the cloth from the cleaning cloth compartment. 2 Open the document processor and wipe the slit glass (a). 3 Wipe the white guide (b) on the document processor. 4 When using the document processor to allow dual scanning, open the top cover of the document processor. a b OPERATION GUIDE 9-3 9 Maintenance 5 Wipe the slit glass. 6 Wipe the white roller. 7 Close the document processor top cover and return the cleaning cloth to the cleaning cloth compartment. 8 Press [End]. Separator Clean the separator regularly (at least monthly) to ensure optimum output quality. 1 9-4 Open the front cover. OPERATION GUIDE Maintenance 2 Remove cleaning brush (blue colored). 3 Pull up and open left cover 1. 4 As shown in the figure, clean dirt from the separator by moving the brush from side to side along the separator. 5 OPERATION GUIDE Put away the cleaning brush, press the specified position of the front cover and left cover 1 to close. 9-5 9 Maintenance Transfer Roller 9-6 1 Open the front cover. 2 Remove the cleaning brush (blue colored). 3 Pull up and open left cover 1. 4 As shown in the figure, clean dirt from the transfer roller by moving the brush from side to side along the roller while rotating the roller by turning the gear at the left end of the roller. OPERATION GUIDE Maintenance 5 Put away the cleaning brush, press the specified position of the front cover and left cover 1 to close. 9 OPERATION GUIDE 9-7 Maintenance Toner Container and Waste Toner Box Replacement When the touch panel displays Add toner, replace the toner without delay even if several more copies are still possible. When replacing the toner container, replace the waste toner box as well. Every time you replace the toner container, be sure to clean the parts as instructed below. Dirty parts may deteriorate output quality. CAUTION: Do not attempt to incinerate the toner container or the waste toner box. Dangerous sparks may cause burns. CAUTION: Do not attempt to force open or destroy the toner container or the waste toner box. 1 Open the front cover. 2 Push up the toner container stopper and slowly pull out the used toner container until its handle is visible WARNING: High voltage parts inside. Handle with care because there is a danger of electric shock. IMPORTANT: Do not pull the toner container all the way out without holding the handle, otherwise it will drop. 9-8 OPERATION GUIDE Maintenance OPERATION GUIDE 3 Keep the stopper up, hold the toner container handle and take out slowly 4 Unwrap a new toner container and tap its top 5-6 times. 5 Shake the toner container at least 10 times horizontally to distribute the toner evenly. 6 Insert the toner container slowly while holding its handle. 9 9-9 Maintenance 7 Using both hands, push in the toner container until it is locked. 8 Remove the waste toner box. 9 Peel the sticker off the waste toner box and remove the cap. 10 Put the cap on the opening in the waste toner box and attach the sticker to the cap 9-10 OPERATION GUIDE Maintenance 11 Put the waste toner box in the supplied plastic bag for disposal and securely tie the mouth of the bag. CAUTION: Do not attempt to incinerate the toner container or the waste toner box. Dangerous sparks may cause burns. CAUTION: Do not attempt to force open or destroy the toner container or the waste toner box. 12 Install a new waste toner box. 9 13 Remove the cleaning brush (blue colored). OPERATION GUIDE 9-11 Maintenance 14 Pull up and open left cover 1 15 As shown in the figure, clean dirt from the separator by moving the brush from side to side along the separator. 16 As shown in the figure, clean dirt from the transfer roller by moving the brush from side to side along the roller while rotating the roller by turning the gear at the left end of the roller. 17 Put away the cleaning brush after the cleaning. Close the front cover and left cover 1 by pressing specified part. 9-12 OPERATION GUIDE Maintenance 18 Open the Multi Purpose Tray and remove the filters F1 and F2. F1 T F2 19 Remove dust from the filters using a vacuum cleaner or dry cloth. IMPORTANT: Do not wash the filters with water. Do not use the attached cleaning brush. 9 20 Put the filters back in place and close the Multi Purpose Tray. NOTE: Return the exhausted toner container and waste toner box to your dealer or service representative. The collected toner container and waste toner box will be recycled or disposed in accordance with the relevant regulations. OPERATION GUIDE 9-13 Maintenance 9-14 OPERATION GUIDE 10 Troubleshooting This chapter explains how to solve problems with the machine. • • • Solving Malfunctions .........................................................................10-2 Responding to Error Messages ........................................................10-6 Clearing Paper Jams ......................................................................10-15 OPERATION GUIDE 10-1 Troubleshooting Solving Malfunctions The table below provides general guidelines for problem solving. If a problem occurs with your machine, look into the checkpoints and perform procedures indicated on the following pages. If the problem persists, contact your Service Representative. Symptom Checkpoints Reference Page Corrective Actions The operation panel does not respond when the main power switch is turned on. Is the machine plugged in? Plug the power cord into an AC outlet. — Pressing the Start key does not produce copies. Is there a message on the touch panel? Determine appropriate response to the message and respond accordingly. 10-6 Is the machine in Sleep mode? Press the Power key to recover the machine from Sleep mode. The machine will be ready to copy within 15 seconds. 2-9 Are the originals loaded correctly? When placing originals on the platen, place them face-down and align them with the original size indicator plates. 2-30 When placing originals in the optional document processor, place them face-up. 2-32 Is the machine in Auto Density mode? Set the correct density level for auto density. — Is the machine in Manual Density mode? Use [Image Quality] to set the correct density level. Blank sheets are ejected. Printouts are too light. 10-2 When changing the default density level, adjust the density manually and choose the desired level. — Is the toner distributed evenly within the toner container? Shake the toner container from side to side about several times. 9-8 Is there a message indicating the addition of toner? Replace the toner container. 9-8 Is the paper damp? Replace the paper with new paper. 2-19 Is the drum dirty? Carry out Drum Refresh. Is EcoPrint mode enabled? Disable EcoPrint mode. OPERATION GUIDE Troubleshooting Symptom Printouts are too dark. Checkpoints Corrective Actions Is the machine in Auto Density mode? Set the correct density level for auto density. Is the machine in Manual Density mode? Use [Image Quality] to set the correct density level. When changing the default density level, adjust the density manually and choose the desired level. Reference Page — — Copies have a moire pattern (dots grouped together in patterns and not aligned uniformly). Is the original a printed photograph? Set the image quality to [Print Photo]. Printouts are not clear. Did you choose appropriate image quality for the original? Select appropriate image quality. 9-2 Printouts are dirty. Is the platen or the document processor dirty? Clean the platen or the document processor. 9-2 Is the transfer roller dirty? Brush the transfer roller clean. 9-6 Is the drum dirty? Carry out Drum Refresh. Is the Printed Document Guard Kit enabled? Disable the Printed Document Guard Kit. Printouts are fuzzy. Is the machine being used in very humid conditions? Carry out Drum Refresh. Images are skewed. Are the originals placed correctly? When placing originals on the platen, align them with the original size indicator plates. 2-32 When placing originals in the optional document processor, align the original width guides securely before placing the originals. 2-32 Is the paper loaded correctly? Check the position of the paper width guides. 2-33 Is the paper loaded correctly? Load the paper correctly. 2-20 Is the paper of the supported type? Is it in good condition? Remove the paper, turn it over, and reload it. 2-20 Is the paper curled, folded or wrinkled? Replace the paper with new paper. 2-20 Are there any loose scraps or jammed paper in the machine? Remove any jammed paper. 10-15 Paper often jams. OPERATION GUIDE 10 10-3 Troubleshooting Symptom Checkpoints Reference Page Corrective Actions Printouts from the document processor have black lines. Is the slit glass dirty? Clean the slit glass. 9-3 Printouts are wrinkled. Is the paper separator of the paper feed unit dirty? Clean the paper separator. 9-4 Is the paper damp? Replace the paper with new paper. 2-19 Is the paper set in a proper orientation? Change the orientation in which the paper is positioned. — Is the machine plugged in? Plug the power cord into an AC outlet. — Is the machine powered on? Turn on the main power switch. 3-2 Is the printer cable connected? Connect the correct printer cable securely. 2-5 Was the machine powered on before the printer cable was connected? Power on the machine after connecting the printer cable. 2-5 Is Press Status Key... displayed at the top of the screen? Press the Status/Job Cancel key, [Printing Jobs], and then [Resume All Print Jobs] to restart printing. — Documents are printed improperly. Are the application software settings at the PC set properly? Check that the printer driver and application software settings are set properly. — While the operation panel was being used, the keys locked up and do not respond when pressed. Is the operation panel locked? Embedded Check the panel lock setting in Embedded Web Server and change Web the setting if necessary. Server Operation Guide Cannot print with USB memory. Was the USB memory formatted with a machine other than this machine? Format the USB memory with this machine. Is the USB host blocked? Select Unblock in the USB host settings. Check that the USB memory is securely plugged into the machine. — — Have you selected 200×100dpi Normal or 200×400dpi Super Fine for the scan resolution? Select a scan resolution other than 200×100dpi Normal or 200×400dpi Super Fine when sending an image. — Cannot print. When displaying an image sent from the machine on the PC, an image size is shrunk vertically or horizontally. 10-4 OPERATION GUIDE Troubleshooting Symptom USB memory not recognized. Perform Gray Adjustment in the System Menu. is displayed. Checkpoints Corrective Actions Check that the USB memory is securely plugged into the machine. — Is the USB host blocked? Select Unblock in the USB host settings. Over long periods of use, the effects of the ambient temperature and humidity can cause color output hues to vary slightly. Whenever the printed hues differ from the original document or image, carry out Gray Adjustment. Reference Page — 10 OPERATION GUIDE 10-5 Troubleshooting Responding to Error Messages If the touch panel displays any of these messages, follow the corresponding procedure. Alphanumeric Error Message Checkpoints Reference Page Corrective Actions Acceptable staple count exceeded. Is the acceptable staple count exceeded? For details, refer to Specifications on page Appendix-26. Press [Continue] to print without stapling. Press [Cancel] to cancel the job. — Add paper in cassette 1. Is the indicated cassette out of paper? Load paper. 2-19 Add paper in Multi Purpose tray. Is the paper of the selected size loaded in the multi purpose tray? Load the paper in the multi purpose tray which is of the size and type indicated on the touch panel. 2-22 Add staples. Has any of the document finisher run out of staples? If the staples are depleted, the machine will stop and the location of staple depletion will be indicated on the touch panel. Leave the machine on and follow the instruction to replace the staple case. Press [Continue] to print without stapling. Press [Cancel] to cancel the job. — Add toner. – Replace the toner container. 9-8 Box is not found. – This job is canceled because the specified box cannot be found. Press [End]. — Box limit exceeded. – Document box is full, and no further storage is available; Job is canceled. Press [End]. — – Repeat Copy box is full, and no further repeat copy is available. Press [Continue] to print scanned pages. Press [Cancel] to cancel the job. — – An error has occurred when connecting to the authentication server. Refer to Responding to Authentication Server Connection Error for the error message and corrective actions. 10-14 Cannot connect to Authentication Server. 10-6 OPERATION GUIDE Troubleshooting Error Message Checkpoints Corrective Actions Reference Page Cannot duplex print on this paper. Did you select a paper size/ media type that cannot be duplex printed? Select the available paper type. Press [Continue] to print without using Duplex. 3-11 Cannot execute this job. – This job is canceled because it is restricted by Job Accounting. Press [End]. — Cannot offset this paper. Did you select a paper size/ media type that cannot be offset? Select the available paper size/type. Press [Continue] to print without using Offset. 3-13 Cannot print the specified number of copies. – Only one copy is available due to processing too many jobs in parallel. Press [Continue] to continue printing. Press [Cancel] to cancel the job. — Cannot staple at the specified position. Have you selected a position that cannot be stapled? Select a position that can be stapled. Press [Continue] to print without using Staple. — Cannot staple this paper. Did you select a paper size/ type that cannot be stapled? Select the available paper size/type. Press [Continue] to print without using Staple. — Check the cover. Is there any cover which is open? Close the cover indicated on the touch panel. — Check the document processor. Is the document processor open? Close the document processor. — Is the top cover of the document processor open? Close the top cover of the document processor. 10-25 Check the finisher. Is the document finisher set correctly? Set the document finisher correctly. For details, refer to the respective Operation Guides. — Clean the slit glass. – Clean the slit glass using the cleaning cloth supplied with the document processor. 9-3 Confidential document is detected. – The machine detects the documents guard pattern. The scanned document is printed in blank and sending of the document is canceled. Failed to specify Job Accounting. – The job is canceled. Press [End]. — Failed to store job retention data. – The job is canceled. Press [End]. — OPERATION GUIDE 10 10-7 Troubleshooting Error Message Checkpoints Reference Page Corrective Actions FAX box limit exceeded. – FAX box is full, and no further storage is available. The job is canceled. Press [End]. Try to perform the job again after printing or deleting data from the FAX box. — Finisher tray is full of paper. Is the acceptable storage capacity exceeded for the document finisher tray? Remove paper from the document finisher tray. If printing can be restarted, the touch panel display will prompt you to press [Continue]. Then press [Continue]. — Hard Disk error. Job is canceled. Press [End]. – An error has occurred on the hard disk. The possible error codes and their descriptions are as follows. 01: Initialization error. Initialize the hard disk. 04: Insufficient space on the hard disk to complete this operation. Move or delete data stored on the hard disk to increase available space. — Incorrect account ID. – The Account ID does not match. Check the registered Account ID. — Incorrect box password. – Enter the correct password. — Incorrect Login User Name or Password. – Enter correct login user name or password. — Job Accounting restriction exceeded. Is the acceptable printing count restricted by Job Accounting exceeded? The printing count exceeded the acceptable count restricted by Job Accounting. Cannot print any more. This job is canceled. Press [End]. — Job separator is full of paper. Is the maximum capacity of Take some paper out of the job the job separator exceeded? separator. Printing then resumes. — KPDL error. – PostScript error has occurred. The job is canceled. Press [End]. — Machine failure. – Internal error has occurred. Make a note of the error code displayed on the touch panel. Turn off the machine, unplug the power cord, and contact your Service Representative. — Maximum number of scanned pages. Is the acceptable scanning count exceeded? Only one copy of the scanned pages is available. Press [Continue] to print, send or store the scanned pages. Press [Cancel] to cancel printing, sending or storing. — 10-8 OPERATION GUIDE Troubleshooting Error Message Checkpoints Corrective Actions Reference Page – Unable to continue the job as the memory is used up. Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job. — – The process cannot be performed due to insufficient memory. If only [End] is available, press [End]. The job will be canceled. — Paper jam. – If a paper jam occurs, the machine will stop and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instruction to remove the jammed paper. 10-15 Print overrun. – Warning. Low printer memory. The job was paused. Press [Continue] to re-start the job. — Removable memory error. – This job is canceled. Press [End]. — Removable memory is full. – This job is canceled. Press [End]. — Replace all originals and press [Continue]. – Remove originals from the document processor, put them back in their original order, and place them again. Press [Continue] to resume printing. Press [Cancel] to cancel the job. 2-32 Replace the waste toner box. – The waste toner box is full. Replace the waste toner box. 9-8 Remove all originals in the document processor. Are there any originals left in the document processor? Remove originals from the document processor. — Scanner memory is full. – Scanning cannot be performed due to insufficient memory of scanner. Only one copy of the scanned pages is available. Press [Continue] to print, send or store the scanned pages. Press [Cancel] to cancel the printing job. — Memory is full. OPERATION GUIDE 10 10-9 Troubleshooting Error Message Checkpoints Reference Page Corrective Actions Send error. – An error has occurred during transmission.Refer to Responding to Send Error for the error code and corrective actions. 10-11 Set the waste toner box. – The waste toner box is not installed correctly. Set it correctly. 9-8 Staple jam. – If a staple jam occurs, the machine will stop and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instruction to remove the jammed staple. — System error. – System error has occurred. Confirm that the Attention indicator is lighting, and then turn the main power switch off and on. — The phone receiver is off the hook. – Put down the receiver. — The removable memory is not formatted. Is the removable memory formatted by this machine? Use the removable memory formatted by this machine. — Top tray of the machine is full of paper. – Remove paper from the top tray and press [Continue]. — Unknown Toner Installed. PC Is the unauthorized product installed? Install our genuine product that is specified for this machine. — Warning low memory. – Job cannot be started. Try again later. — 10-10 OPERATION GUIDE Troubleshooting Responding to Send Error When an error occurs during transmission, Send Error appears. Check the error code and error message below, and follow the corresponding corrective actions. Error Code 1101 1102 1103 Error Message Corrective Actions Reference Page Failed to send the e-mail. Failed to send i-FAX. Check the host name of the SMTP 2-17 server on the Embedded Web Server. Failed to send via FTP. Check the host name of FTP. Failed to send via SMB. Check the host name of SMB. Failed to send via SMB. Check the SMB settings. - Login user name and login password * If the sender is a domain user, specify the domain name. - Host name - Path Failed to send the e-mail. Failed to send i-FAX. Check the followings on the Embedded Web Server. - SMTP login user name and login password - POP3 login user name and login password Failed to send via FTP. Check the FTP settings. - Login user name and login password * If the sender is a domain user, specify the domain name. - Path - Folder share permissions of the recipient Failed to send via SMB. Check the SMB settings. - Login user name and login password * If the sender is a domain user, specify the domain name. - Path - Folder share permissions of the recipient 3-25 Failed to send via FTP. Check the FTP settings. - Path - Folder share permissions of the recipient 3-25 OPERATION GUIDE 3-25 10 10-11 Troubleshooting Error Code Error Message Corrective Actions Failed to send the e-mail. Check the e-mail address. * If the address is rejected by the domain, you cannot send the e-mail. 3-24 Failed to send i-FAX. Check the i-FAX address. *If the address is rejected by the domain, you cannot send i-FAX. FAX System (S) Operation Guide Chapter 8 "Internet Faxing (i-FAX) (Option)" Failed to send via SMB. Select [On] of the SMB settings on the Embedded Web Server. 2-17 Failed to send the e-mail. Select [On] of the SMTP settings on the Embedded Web Server. Failed to send via FTP. Select [On] of the FTP settings on the Embedded Web Server. Failed to send i-FAX. Select [On] of the i-FAX settings on the Embedded Web Server. FAX System (S) Operation Guide Chapter 8 "Internet Faxing (i-FAX) (Option)" 1106 Failed to send the e-mail. Failed to send i-FAX. Check the sender address of SMTP on the Embedded Web Server. 2-17 1131 Failed to send via FTP. Select [On] of the secure protocol settings on the Embedded Web Server. 2-17 1132 Failed to send via FTP. Check the followings of the FTP server. - Is FTPS available? - Is the encryption available? 2-17 2101 Failed to send via SMB. Failed to send via FTP. Check the network and SMB settings. Check the network and FTP settings. - The network cable is connected. - The hub is not operating properly. - The server is not operating properly. - Host name and IP address - Port number 2-17 Failed to send the e-mail. Failed to send i-FAX. Check the network and Embedded Web Server. - The network cable is connected. - The hub is not operating properly. - POP3 server name of the POP3 user - SMTP server name 1104 1105 10-12 Reference Page OPERATION GUIDE Troubleshooting Error Code 2102 2103 Error Message Corrective Actions Reference Page Failed to send via FTP. Check the followings of the FTP server. - Is FTP available? - The server is not operating properly. Failed to send the e-mail. Failed to send i-FAX. Check the network. - The network cable is connected. - The hub is not operating properly. - The server is not operating properly. 2201 Failed to send the e-mail. Failed to send via FTP. Failed to send via SMB. Failed to send i-FAX. Check the network. - The network cable is connected. - The hub is not operating properly. - The server is not operating properly. – 2202 Failed to send the e-mail. Failed to send via FTP. Failed to send i-FAX. 2203 Failed to send via FTP. Failed to send via SMB. 2231 Failed to send via FTP. 2204 Failed to send the e-mail. Failed to send i-FAX. Check the e-mail size limit of the SMTP settings on the Embedded Web Server. 2-17 3101 Failed to send the e-mail. Failed to send i-FAX. Check the authentication methods of both the sender and the recipient. – Failed to send via FTP. Check the network. - The network cable is connected. - The hub is not operating properly. - The server is not operating properly. 3201 Failed to send the e-mail. Failed to send i-FAX. Check the SMTP user authentication method of the recipient. – 5101 5102 5103 5104 7102 720f – Turn the main power switch off and back on. If this error occurs several times, make a note of the displayed error code and contact your service representative. – 9181 – The scanned original exceeds the acceptable number of pages of 999. Send the excess pages separately. – OPERATION GUIDE – 10 10-13 Troubleshooting Responding to Authentication Server Connection Error If an error occurs when connecting to the authentication server, check the error message and follow the corresponding corrective action appears on the operation panel. Symptom Corrective Actions Cannot connect to authentication server. Set machine time to match the server’s time. Cannot connect to authentication server. Check the domain name. Reference Page 2-11 Check the host name. Check the connection status with the server. — Responding to an Attention Indicator Flashes If an attention indicator flashes, press [Status/Job Cancel] to check an error message. If the message is not indicated on the touch panel when [Status/Job Cancel] is pressed or the attention indicator flashes for 1.5 seconds, check the following. Symptom Cannot send fax. 10-14 Checkpoints Corrective Actions Reference Page Is the modular cord connected correctly? Connect the modular cord correctly. — Is Permitted FAX No. or Permitted ID No. registered correctly? Check Permitted FAX No. and Permitted ID No.. FAX System (S) Operation Guide Chapter 6 "Registering Permit FAX No." and "Registering Permit ID No." Has a communication error occurred? Check error codes in the TX/RX Result Report and Activity Report. If the error code starts with "U" or "E", perform the corresponding procedure. FAX System (S) Operation Guide Appendix "Error Code List" Is the destination FAX line busy? Send again. — Does the destination FAX machine respond? Send again. — Is there an error other than above? Contact your Service Representative. — OPERATION GUIDE Troubleshooting Clearing Paper Jams Job No.: 000021 Job Name: doc101020081010 If a paper jam occurs, the touch panel will display Paper misfeed and the machine will stop. Refer to these procedures to remove the jammed paper. User Name: Mike Paper jam. 1.Remove the paper. 2.Open the fuser cover and remove the jammed paper. 3.Close the cover. JAM 01/03 Hold 08/08/2009 Status 10:10 Jam Location Indicators If a paper jam occurs, the location of the jam will be displayed as the following figure with a letter corresponding to the affected component in the machine. Clearing instructions will also be displayed. Job No : 000021 Job Name: doc101020081010 User Name: M ke Paper jam. H 1 Remove the paper 2 Open the fuser cover and remove the jammed paper 3 Close the cover I JAM K J I Hold Statu G I 01/03 08/08/2009 10 10 I I G I D I A I I I Paper Jam Location Indicator Paper Jam Location F B C C Reference Page A Cassette 1 10-16 B Cassette 2 10-17 C Cassette 3 or 4 (Option) 10-18 D Multi Purpose Tray 10-19 E Inside the left cover 1, 2 or 3 10-20 F Duplex Unit 10-20 G Paper Feed Unit 10-22 OPERATION GUIDE 10 D 10-15 Troubleshooting Paper Jam Location Indicator Paper Jam Location Reference Page H Document processor (Option) 10-25 I Document finisher (Option) 10-25 J Built-in finisher (Option)) 10-27 K Job Separator (Option) 10-29 After you remove the jam, the machine will warm up again and the error message will be cleared. The machine resumes with the page which jam has occurred. Precautions with Paper Jams • Do not reuse jammed paper. • If the paper tears during removal, be sure to remove any loose scraps of paper from inside the machine. Scraps of paper left in the machine could cause subsequent jamming. • Discard paper that has jammed in the optional document finisher. A page affected by a paper jam will be printed again. CAUTION: The fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger of getting burned. Cassette 1 Follow the steps below to clear paper jams in cassette 1. 10-16 1 Pull up left cover 1 lever and open the left cover 1. 2 Remove any paper. OPERATION GUIDE Troubleshooting 3 Pull out cassette 1. 4 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 5 Push cassette 1 back in place securely. 6 Press the specified position to close left cover 1. 10 Cassette 2 Follow the steps below to clear paper jams in cassette 2. 1 OPERATION GUIDE Open left cover 2. 10-17 Troubleshooting 2 Remove any paper. 3 Pull out cassette 2. 4 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 5 Push cassette 2 back in place securely. 6 Close left cover 2. Optional Cassettes 3 and 4 Follow the steps below to clear paper jams in cassettes 3 or 4 when using the optional paper feeder. 1 10-18 Open left cover 3. OPERATION GUIDE Troubleshooting 2 Remove any paper. If the paper tears, remove every loose scrap from inside the machine. 3 Pull out the cassette in use. 4 Remove the paper. 10 5 Push the cassette back in place securely. 6 Close left cover 3. Multi Purpose Tray Follow the steps below to clear paper jams in the multi purpose tray. 1 OPERATION GUIDE Remove the paper from the multi purpose tray. 10-19 Troubleshooting Inside the Left Covers 1, 3 and 4 Follow the steps below to clear paper jams inside left cover 1, 3 or 4 when using the optional paper feeder. 1 Pull up left cover 1 lever and open the left cover 1. 2 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 3 Press the specified position to close left cover 1. Duplex Unit Follow the steps below to clear paper jams in the duplex unit. 1 10-20 Pull up left cover 1 lever and open the left cover. OPERATION GUIDE Troubleshooting 2 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 3 Press the specified position to close left cover 1. Duplex Unit and Cassette 1 Follow the steps below to clear paper jams in duplex unit and cassette 1. 1 Pull up left cover 1 lever and open the left cover. 10 2 Remove any paper. If the paper tears, remove every loose scrap from inside the machine. OPERATION GUIDE 10-21 Troubleshooting 3 Lift duplex unit and remove any paper. If the paper tears, remove every loose scrap from inside the machine. 4 Pull out cassette 1 and remove the paper. If the paper tears, remove every loose scrap from inside the machine. 5 Push cassette 1 back in place securely. 6 Press the specified position to close left cover 1. Paper Feed Unit Follow the steps below to clear paper jams in the paper feed unit. 1 10-22 Pull up left cover 1 lever and open the left cover 1. OPERATION GUIDE Troubleshooting 2 Remove any paper. If the paper tears, remove every loose scrap from inside the machine. 3 Open front cover. 4 Turn the lower green knob (A1) clockwise. 10 5 Remove any paper. If you cannot remove the paper, proceed with the next step. OPERATION GUIDE 10-23 Troubleshooting 6 Pull out paper feed unit (A2). 7 Open paper feed unit cover (A3) and remove any paper. If the paper tears, remove every loose scrap from inside the machine. 8 If the paper is torn, pull paper feed unit (A2) all the way out and lift it slightly to remove any paper. 9 Remove the paper. If you cannot remove the paper, proceed with the next step. 10 Push paper feed unit (A2) back in place, and close the front cover. 10-24 OPERATION GUIDE Troubleshooting 11 Press the specified position to close left cover 1. Optional Document Processor Follow the steps below to clear paper jams in the optional document processor. 1 Remove any paper from the original tray. 2 Open the document processor top cover. 10 3 Remove any paper. If the original tears, remove every loose scrap from inside the machine. OPERATION GUIDE 10-25 Troubleshooting If the original is difficult to remove, turn the dial. The original will scroll out to a position where it can be removed easily. If the original tears, remove every loose scrap from inside the machine. 4 Lift up reverse unit. 5 Remove the paper. If the original tears, remove every loose scrap from inside the machine. 6 Put reverse unit back in its original place and close the document processor top cover. 7 Reload the originals on the document processor tray. Optional Document Finisher If a misfeed occurs in the optional document finisher, refer to the respective Operation Guides to clear the jam. 10-26 OPERATION GUIDE Troubleshooting Built-in Finisher Follow the steps below to clear paper jams in the optional built-in finisher. 1 Remove any paper in the output section. If the paper tears, remove every loose scrap from inside the machine. 2 Remove the output tray. 3 Lift up the handle on left cover 1 and open left cover 1. (3 ) (1 ) (2 ) OPERATION GUIDE 4 Remove any paper. 5 Close left cover 1. 10-27 10 Troubleshooting 6 Re-attach the output tray. 7 Lower the finisher process tray. 8 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 9 10-28 Raise the finisher process tray OPERATION GUIDE Troubleshooting Job Separator Follow the steps below to clear paper jams in the optional job separator. 1 Remove any paper in the output section. If the paper tears, remove every loose scrap from inside the machine. 2 Pull up left cover 1 lever and open left cover 1. 3 Remove the paper. If the paper tears, remove every loose scrap from inside the machine. 4 OPERATION GUIDE Press the indicated position to close left cover 1. 10-29 10 Troubleshooting 10-30 OPERATION GUIDE 11 Management This chapter explains the following operations. • • • User Login Administration.................................................................11-2 Job Accounting ...............................................................................11-14 Data Security Kit Operations...........................................................11-27 OPERATION GUIDE 11-1 Management User Login Administration User login administration specifies how the user access is administered on this machine. Enter correct login user name and password for user authentication to login. Access are in three levels - User, Administrator, and Machine Administrator. The security levels can be modified only by the machine administrator. First User Login Administration Follow these steps for the first user login administration. Enable user login administration. (page 11-2) Add a user.(page 11-5) Log out.(page 11-4) The registered user logs in for operations.(page 11-3) Enabling/Disabling User Login Administration This enables user login administration. Select one of the following authentication methods: Item Description Local Authentication User authentication based on user properties on the local user list stored in the machine. Network Authentication User authentication based on Authentication Server. Use a user property stored in Authentication Server to access the network authentication login page. Use the procedure below to enable user login administration. 11-2 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of User Login Setting and then [Change] of User Login. OPERATION GUIDE Management 5 User Login/Job Accounting - User Login User login administration. Select authentication method. Select [Local Authentication] or [Network Authentication]. Select [Off] to disable user login administration. Off Host Name Local Authentication If you select [Network Authentication], enter the host name (62 characters or less) and domain name (256 characters or less) for the Authentication Server. Select [NTLM] or [Kerberos] as the server type. # Keys Domain Name Network Authentication Expansion Authentication Server Type NTLM Kerberos Cancel OK 08/08/2009 Status 10:10 NOTE: If the login user name and password are rejected, check the following settings. • Network Authentication setting of the machine • User property of the Authentication Server • Date and time setting of the machine and the Authentication Server If you cannot login because of the setting of the machine, login with any administrator registered in the local user list and correct the settings. If the server type is [Kerberos], only domain names entered in uppercase will be recognized. 6 Press [OK]. Login/Logout Once you enable user login administration, a login user name and password entry screen appears each time you use this machine. Login 11 Use the procedure below to login. 1 Enter login user name and password. Login to: Local Login User Name abcdef Press [# Keys] to enter the login data using the numeric keys. # Keys Login Password If the screen below appears during the operations, press [Login User Name]. 2 ******** Enter the login user name and press [OK]. # Keys NOTE: Refer to the Character Entry Method on IC Card Login Check Counter Status Cancel Appendix-10 for details on entering characters. Login 08/08/2009 10:10 3 Press [Login Password]. Press [# keys] to enter the login data using the numeric keys. OPERATION GUIDE 11-3 Management 4 Enter the login password and press [OK]. NOTE: If Job Accounting is enabled, you can browse the number of pages printed and the number of pages scanned by pressing [Check Counter]. If Network Authentication is selected as the user authentication method, either Local or Network can be selected as the authentication destination. 5 Check the login user name and password are correct, and press [Login]. Logout To log out the machine, press the Logout key to return to the login user name/login password entry screen. Auto Logout Logout is automatically executed in the following cases: 11-4 • When the Power key is pressed to enter the sleep mode • When auto sleep is activated • When auto panel reset is activated OPERATION GUIDE Management Adding a User This adds a new user. You can add Up to 1,000 users (including the default login user name). The table below explains the user information to be registered. Item Description User Name* Enter the name displayed on the user list (up to 32 characters). Login User Name* Enter the login user name to login (up to 64 characters). The same login user name cannot be registered. Login Password* Enter the password to login (up to 64 characters). Access Level* Select Administrator or User for user access privileges. Account Name Add an account where the user belongs. The user, who registered his/her account name, can login without entering the account ID. Refer to Job Accounting on page 11-14. E-mail Address The user can register his/her E-mail address. The registered address will be automatically selected for subsequent operations that need any E-mail function. * Mandatory at user registration. NOTE: By default, one of each default user with machine administrator rights and administrator privileges is already stored. Each user's properties are: Machine Administrator User Name: Login User Name: Login Password: Access Level: DeviceAdmin 42 ppm model: 4200, 52 ppm model: 5200 42 ppm model: 4200, 52 ppm model: 5200 Machine Administrator When the optional Data Security Kit is installed, the login user name and login user password are as shown below. 42 ppm model: 42004200, 52 ppm model: 52005200 Administrator User Name: Login User Name: Login Password: Access Level: Admin Admin Admin Administrator When the optional Data Security Kit is installed, the login user name and login user password are same. It is recommended to periodically change the user name, login user name and login password regularly for your security. Use the procedure below to register a new user. OPERATION GUIDE 1 Login as a user with administrator rights. 2 Press the System Menu key. 3 Press [User Login/Job Accounting]. 4 If user login administration is disabled, the user authentication screen appears. Enter your login 11-5 11 Management user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. User: User Name: Change 01 User Login User Name: Change Log n Password: Change Account Name: 0099 5 Press [Next] of User Login Setting, [Register/Edit] of Local User List, and then [Add]. 6 Press [Change] of User Name. 7 Enter the user name and press [OK]. Change ********** Access Level: User NOTE: Refer to the Character Entry Method on Change Appendix-10 for details on entering characters. 02 Account E-mail Address: IC Card Information: Change Change Empty [email protected] Cancel 8 Enter the login user name and E-mail address following 6 and 7 above. 9 Press [Change] of Login Password and then [Password]. Register 08/08/2009 Status 10:10 10 Enter the login password and press [OK]. 11 Press [Confirm Password]. 12 Enter the same login password to confirm and press [OK]. 13 Press [OK]. 14 Press [Change] of Access Level. 15 Select the user access privilege and press [OK]. 16 Press [Change] of Account Name. 17 Select the account and press [OK]. User: - Account Name Select account to which this user will be attached. Sort Account Name Name Account ID 01 Account 00001000 02 Account 00002000 03 Account 00003000 Search(Name) Search(ID) 1/2 Other Account 04 Account 05 Account NOTE: Select [Name] and [ID] from the Sort pull-down menu to sort the account list. Press [Search(Name)] or [Search(ID)] to search by account name or account ID. 00004000 00005000 Detail Cancel Status OK 08/08/2009 10:10 18 Press [Register] to add a new user on the local user list. 11-6 OPERATION GUIDE Management Changing User Properties User properties can be changed. Types of user properties that could be changed may be different depending on user access privilege. For a user with administrator rights who logs in User properties can be changed and users can be deleted. The items, which can be added, are all able to be changed. Use the procedure below to change the user properties. 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of User Login Setting and [Register/ Edit] of Local User List. 5 Select the user whose properties you wish to change. NOTE: Select [Name] and [Login Name] from the Sort pull-down menu to sort the user list. Press [Search(Name)] or [Search(Login)] to search by name or login user name. The procedure differs depending on the details to be edited. Changing user information User: User Name: Change 0099 Access Level: Log n Password: Change ********** Change User E-mail Address: Press [Detail]. 2 Refer to steps 6 to 17 of Adding a User to change a user property. 3 Press [Register]. 4 Press [Yes] in the registration confirmation screen. The user information is changed. Change 01 User Login User Name: 1 Account Name: Change 02 Account Change [email protected] IC Card Information: Cancel Status OPERATION GUIDE Change Empty Register 08/08/2009 10:10 11-7 11 Management Deleting a user 1 Press [Delete]. 2 Press [Yes] on the screen to confirm deletion. The selected user will be deleted. NOTE: The default user with administrator rights cannot be deleted. For a user without administrator rights who logs in These users can partially change their own user properties including user name, login password, and E-mail address. Although login user name, access level, or account name cannot be changed, the users can check the present status. Use the procedure below to change user properties. User: User Name: 1 Press the System Menu key. 2 Press [User Property]. 3 Refer to steps 6 to 17 of Adding a User to change user properties. Change 01 User Login User Name: Detail 0099 Account Name: User [email protected] Detail 02 Account Change IC Card Information: Empty Cancel Status Press [Detail] of Login User Name or Account Name to check the present status. Change ********** Access Level: E-mail Address: Login Password: Register 08/08/2009 10:10 4 11-8 Press [Register] to finalize changed user properties. OPERATION GUIDE Management Unknown login user name Job This specifies the behavior for handling the jobs sent with unknown login user names or User ID (i.e. unsent IDs). If the User Login is set to invalid and Job Accounting is set to valid, follow the procedure when the Account ID is unknown. The table below shows the available settings. Item Description Reject The job is rejected (not printed). Permit The job is permitted to be printed. Use the procedure below to process jobs sent from unknown users. 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Change] of Unknown ID Job. 5 Press [Reject] or [Permit]. 6 Press [OK]. 11 OPERATION GUIDE 11-9 Management Group Authorization Settings Set restrictions of the machine usage by each individual group registered in the authentication server. NOTE: To use the group authorization settings, [Network Authentication] must be selected for the authentication method in Enabling/Disabling User Login Administration on page 11-2. Select [On] for LDAP in Protocol Detail on page 8-66. Group Authorization Use the group authorization. Use the procedure below. 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of User Login Setting, [Next] of Group Authorization Set., and then [Change] of Group Authorization. 5 Press [On]. 6 Press [OK]. Group List Register the groups that is restricted the machine usage. Up to 20 groups can be individually registered. Other users and groups belong to Others. The table below explains the group information to be registered. Item Description Group ID* Enter the ID displayed on the group list (between 1 and 4294967295). Group Name Enter the name displayed on the group list (up to 32 characters). Access Level Select Administrator or User for group access privileges. Print Restriction Select whether or not to reject usage of print functions for the printer. Copy Restriction Select whether or not to reject usage of copy functions. Send Restriction Select whether or not to reject usage of the send functions. FAX TX Restriction Select whether or not to reject usage of the FAX transmissions. Storing Restr. in Box Select whether or not to reject usage of storing in the document boxes. 11-10 OPERATION GUIDE Management Item Description Storing Restr. in Memory * Select whether or not to reject usage of storing in the removable memory. For Group ID, specify PrimaryGroupID assigned by ActiveDirectory of Windows. If you are using Windows Server 2008, check Attribute Editor tab of user properties. If you are using Windows Server 2000/2003, check ADSIEdit. ADSIEdit is a support tool included on the installation CD-ROM for Windows Server OS (under \SUPPORT\TOOLS). Use the procedure below. User Login/Job Accounting - Group List 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of User Login Setting, [Next] of Group Authorization Set., [Register/Edit] of Group List, and then [Add]. Register the groups that is restricted the machine usage. (Maximum: 20) Group ID Group Name Others Add Detail Delete Cancel Register 08/08/2009 Status 11 10:10 Group:xxx 5 Press [Change] of Group ID. Group ID: Change Group Name: Change 6 Enter the group ID and press [OK]. Access Level: Change Print Restriction: Change 7 Press [Change] of Group Name. Copy Restriction: Change 8 Enter the group name and press [OK]. Send Restriction: NOTE: Refer to the Character Entry Method on Change 1/2 Cancel Status Appendix-10 for details on entering characters. Register 08/08/2009 10:10 9 Press [Change] of Access Level. 10 Select the user access privilege and press [OK]. 11 Press [Change] of Print Restriction. 12 Select [Reject Usage] or [Off] and press [OK]. OPERATION GUIDE 11-11 Management 13 Follow steps 11 and 12 above to set Copy Restriction, Send Restriction, FAX TX Restriction, Storing Restr. in Box, and Storing Restr. in Memory. 14 Press [Register] to add a new group on the group list. Obtain Network User Property Set the required information to obtain the network user property from the LDAP server. NOTE: To obtain the network user property from the LDAP server, [Network Authentication] must be selected for the authentication method in Enabling/Disabling User Login Administration on page 11-2. The table below explains the required information to be registered.Use the procedure below. Item Description Server Name*1 Enter the LDAP server name or the IP address (up to 64 characters). Port Set the LDAP port number or use the default port 389. Name 1*2 Enter the LDAP Attribute to obtain the user name to be displayed from the LDAP server (up to 32 characters). Name 2*3 Enter the LDAP Attribute to obtain the user name to be displayed from the LDAP server (up to 32 characters). E-mail Address*4 Enter the LDAP Attribute to obtain the e-mail address from the LDAP server (up to 32 characters). Search Timeout Set the amount of time to wait before time-out in seconds (from 5 to 255 seconds). LDAP Security Select the type of encryption according to the type of security employed by the LDAP server. *1 *2 *3 *4 11-12 If using Active Directory of Windows, the server name may be same as the server name entered in the network authentication. If using Active Directory of Windows, displayName of Attribute may be used as Name 1. Name 2 can be left out. When you assign displayName in Name 1 and department in Name 2, and if the value of displayName is "Mike Smith" and the value of department is "Sales" in Active Directory of Windows, the user name appears as Mike Smith Sales. If using Active Directory of Windows, mail of Attribute may be used as E-mail Address. 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator OPERATION GUIDE Management privileges. Refer to Adding a User on page 11-5 for the default login user name and password. User Login/Job Accounting - Network User Property Get the network user information. Off LDAP Server Information: Server Name On Port: 192.181.11.11 389 # Keys 4 Press [Next] of User Login Setting, [Change] of Obtain NW User Property. 5 Press [On]. 6 Press [Server Name]. 7 Enter the LDAP server name or the IP address and press [OK]. 8 Press [# keys] to enter the LDAP port number using the numeric keys. 9 Press [Name 1]. 30 sec. Acquisition of User Information: Name 1 Search Timeout displayName Off Name 2 E-mail Address LDAP Security mail Cancel Status OK 08/08/2009 10:10 10 Enter the LDAP Attribute to obtain the user name to be displayed and press [OK]. 11 Follow steps 9 and 10 above to set Name 2. 12 Press [E-mail Address]. 13 Enter the LDAP Attribute to obtain the e-mail address and press [OK]. 14 Press [Search Timeout] to set the amount of time to wait before time-out. 15 Press [+], [-] or the numeric keys to enter the time. 16 Press [LDAP Security] to select the type of 11 encryption according to the type of security employed by the LDAP server. 17 Select [Off], [LDAP over SSL], or [LDAPv3/TLS] and press [OK]. OPERATION GUIDE 11-13 Management Job Accounting Job accounting Manages the copy/print count accumulated by individual accounts by assigning an ID to each account. Job accounting helps the following activities in business organizations. • Manageability of up to 1,000 individual accounts. • Availability for account IDs with as many as eight digits (between 0 and 99999999) for security. • Integrated management of printing and scanning statistics through the use of an identical account ID. • Tracking the print volume for each account and for all accounts combined. • Restricting the print counter in one-page increments up to 9,999,999 copies. • Resetting the print counter for each account or for all accounts combined. First Job Accounting Setup Follow these steps for the first job accounting setup. Enable job accounting. (page 11-14) Add an account. (page 11-16) Log out. (page 11-15) Other users login for operations. (page 11-15) Enabling/Disabling Job Accounting Enable job accounting. Use the procedure below to specify the job accounting setting. 11-14 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting, and then [Change] of Job Accounting. 5 Press [On]. To disable job accounting, press [Off]. OPERATION GUIDE Management 6 Press [OK]. NOTE: When the display returns to the System Menu default screen, logout is automatically executed and the screen to enter the Account ID appears. To continue the operation, enter the Account ID. Login/Logout If job accounting is enabled, an account ID entry screen appears each time you use this machine. Use the procedure below to login and logout. Login 1 Enter the account ID. In the screen below, enter the account ID using the numeric keys and press [Login]. NOTE: If you entered a wrong character, press the Clear key and enter the account ID again. ******** If the entered account ID does not match the registered ID, a warning beep will sound and login will fail. Enter the correct account ID. Check Counter Status Login 08/08/2009 10:10 By pressing [Counter Check], you can refer to the number of pages printed and the number of pages scanned. When the screen to enter the login user name and password appears If user login administration is enabled, the screen to enter the login user name and password appears. Enter a login user name and password to login. (Refer to Login/Logout on page 11-3.) If the user has already registered the account information, the account ID entry would be skipped. (Refer to Adding a User on page 115.) 2 Proceed to complete the rest of the steps. Logout When the operations are complete, press the Logout key to return to the account ID entry screen. OPERATION GUIDE 11-15 11 Management Adding an Account This section explains how to add a new account. The following entries are required. Item Description Account Name Enter the account name (up to 32 characters). Account ID Enter the account ID as many as eight digits (between 0 and 99999999). Restriction This Prohibits printing/scanning or restricts the number of sheets to load. Refer to Restricting the Use of the Machine on page 11-18. Use the procedure below to register a new account. Account: xx Account Name: Change 01 Account Account ID: 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting, [Register/ Edit] of Accounting List, and then [Add]. 5 Press [Change] of Account Name. 6 Enter the account name and press [OK]. The Account screen reappears. Change 00001000 Copy Restriction (Total): Off Change Print Restriction (Total): Change NOTE: Refer to the Character Entry Method on Off Appendix-10 for details on entering characters. 1/2 Cancel Status Register 08/08/2009 10:10 7 Follow steps 5 and 6 above to enter the Account ID. NOTE: Any account ID that has already registered cannot be used. Enter any other account ID. 11-16 8 Activate or deactivate restriction. Refer to Restricting the Use of the Machine on page 11-18. 9 Press [Register] to add a new account on the Account List. OPERATION GUIDE Management Managing Accounts This changes the registered account information or deletes the account. Use the procedure below to manage accounts. User Login/Job Accounting - Accounting List 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting and then [Register/Edit] of Accounting List. 5 Select an account to change or delete. Register an account that is permitted to use this machine. (Maximum: 1000) Sort Account Name Name Account ID 01 Account 00001000 02 Account 00002000 03 Account 00003000 Search(Name) Press [Search(Name)] or [Search(ID)] to search by account name or account ID. Search(ID) 1/2 Add 04 Account 00004000 05 Account 00005000 Detail The procedure differs depending on the details to be edited. Delete Close 08/08/2009 Status NOTE: Select [Name] or [ID] from the Sort pull-down menu to sort the account names. 10:10 Changing account information Account: xx Account Name: Press [Detail]. 2 Refer to steps 5 to 7 of Adding an Account and steps 2 to 5 of Restricting Using the Machine to change account information. 3 Press [Register]. 4 Press [Yes] in the registration confirmation screen. The account information is changed. Change 01 Account Account ID: Change 00001000 Copy Restriction (Total): 11 1 Change Off Print Restriction (Total): Change Off 1/2 Cancel Status Register 08/08/2009 10:10 Deleting an account OPERATION GUIDE 1 Press [Delete]. 2 Press [Yes]. To delete the account. 11-17 Management Managing the Copier/Printer Counts You can select how the copying and printing page counts are shown - either the total of both or each of copying and printing individually. The selection may influence restriction on the count and count method. Refer to Restricting the Use of the Machine on page 11-18, Counting the Number of Pages Printed on page 11-23 and Printing an Accounting Report on page 11-26 for details. Use the procedure below to set the counting methods. 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting, [Next] of Default Setting and then [Change] of Copier/Printer Count. 5 Press [Total] or [Split]. 6 Press [OK]. Restricting the Use of the Machine This section explains how to restrict the use of the machine by account or the number of sheets available. The items that can be restricted differ depending on whether [Split] or [Total] is selected for Managing the Copier/Printer Counts on page 11-18. Restriction Items [Split] selected for Copier/Printer Count Item 11-18 Detail Copy Restriction (Total) Limits the total number of sheets used for copying. Print Restriction (Total) Limits the total number of sheets used for printing. Scan Restriction (Others) Limits the number of sheets scanned (excludes copying). FAX TX Restriction Limits the number of sheets sent by fax. This is displayed when the optional fax kit is installed. FAX Port Restriction Restricts the ports used for faxing. This is displayed when two optional FAX kits are installed. OPERATION GUIDE Management [Total] selected for Copier/Printer Count Item Detail Print Restriction (Total) Limits the total number of sheets used for copying and printing. Scan Restriction (Others) Limits the number of sheets scanned (excludes copying). FAX TX Restriction Limits the number of sheets sent by fax. This is displayed when the optional fax kit is installed. FAX Port Restriction Restricts the ports used for faxing. This is displayed when two optional FAX kits are installed. Applying Restriction Restriction can be applied in two modes as follows: Item Description Off No restriction given Counter Limit Restricts the print counter in one-page increments up to 9,999,999 copies. Reject Usage Restriction is applied. *Select [Off], [Use Port 1 Only] or [Use Port 2 Only] as the FAX Port Restriction setting. Use the procedure below to select a restriction method. Account:** - Copy Restriction (Total) 1 Follow steps 1 to 4 of Adding an Account on page 11-16. 2 Press [Change] for the item to be restricted. 3 Select the restriction mode. Restrict use of the functions. Off If [Counter Limit] is selected, press [+],[-] or numeric keys to select the number of pages. Limit (1 - 9999999) Counter Limit 99999 page(s) Reject Usage Cancel Status OPERATION GUIDE OK 08/08/2009 10:10 4 Press [OK]. 5 Repeat steps 2 to 4 for other accounts to be restricted. 6 Press [Register]. The restricted account is added. 11-19 11 Management Applying Limit of Restriction This specifies how the machine behaves when the counter has reached the limit of restriction. The table below describes the action taken. Item * Description Immediately * Job stops when the counter reaches its limit. Subsequently Printing/scanning of the job continues but the subsequent job will be rejected. Alert Only Job continues while displaying an alert message. The next job will be prohibited in sending or in storing in the box. Use the procedure below to apply the restriction limit. 11-20 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting, [Next] of Default Setting and then [Change] of Apply Limit. 5 Select [Immediately], [Subsequently], or [Alert Only]. 6 Press [OK]. OPERATION GUIDE Management Default Counter Limit When you add a new account, you can change the default restrictions on the number of sheets used. You can set any number from 1 to 9,999,999 in 1-sheet increments. The items that can be set differ depending on whether [Split] or [Total] is selected for Managing the Copier/ Printer Counts on page 11-18. Available Settings [Split] selected for Copier/Printer Count Item Detail Copy Restriction (Total) Sets the default restriction on the number of sheets used for copying. Print Restriction (Total) Sets the default restriction on the total number of sheets used for printing. Scan Restriction (Others) Sets the default restriction on the number of sheets used for scanning (excludes copying). FAX TX Restriction Sets the default restriction on the number of sheets used for sending faxes. This is displayed when the optional fax kit is installed. [Total] selected for Copier/Printer Count Item Detail Print Restriction (Total) Sets the default restriction on the total number of sheets used for copying and printing. Scan Restriction (Others) Sets the default restriction on the number of sheets used for scanning (excludes copying). FAX TX Restriction Sets the default restriction on the number of sheets used for sending faxes. This is displayed when the optional fax kit is installed. 11 Use the procedure below to specify the counter limits. OPERATION GUIDE 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter a login user name and password, and press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 11-21 Management User Login/Job Accounting - Copy Restriction (Total) 4 Press [Next] of Job Accounting Setting, [Next] of Default Setting and then [Next] of Default Counter Limit. 5 Press [Change] for the item you want to modify and then press [+] or [-] or use the numeric keys to enter the default restriction on the number of sheets. 6 Press [OK]. 7 To set another default restriction, repeat steps 5 to 6. Set the default limit value for restricting use of the functions for each account by counter. (1 - 9999999) 9999999 Cancel Status 11-22 OK 08/08/2009 10:10 OPERATION GUIDE Management Counting the Number of Pages Printed This counts the number of pages printed. Counts are classified into Total Job Accounting and Each Job Accounting. A new count can also be started after resetting the count data which was stored for a certain period of time. Types of the counts are as follows. Item Printed Pages Detail Displays the number of pages copied and printed, and the total number of pages used. You can also use [Count by Paper Size] and [Count by Duplex/Combine] to check the number of pages used. • For copying, you can check the pages used for black and white copying. • For printing, you can check the pages used for black and white printing. • You can use [Count by Paper Size] to check the number of pages used in the paper size set in Counting by Paper Size on page 11-25 as well as the number of pages used in other paper sizes. • You can use the [Count by Duplex/Combine] to check the number of pages used in Duplex (1-sided) mode, Duplex (2sided) mode and the total for both, as well as the pages used in Combine (None) mode, Combine (2in1) mode, Combine (4in1) mode and the total for all three. Scanned Pages Displays the number of pages scanned for copying, faxing* and other functions, as well as the total number of pages scanned. FAX Transmission Pages* Displays the number of pages faxed. FAX Transmission Time* Displays the total duration of fax transmissions. * 11 Only displayed when the optional fax kit is installed. Total Job Accounting/Resetting the Counter This counts the number of pages for all accounts and resets the counts for those accounts together at the same time. Use the procedure below to check and reset the counter. OPERATION GUIDE 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 11-23 Management User Login/Job Accounting - Total Job Accounting Printed Pages: Check Scanned Pages: 2 Press [Next] of Job Accounting Setting and then [Next] of Total Job Accounting. 5 Press [Check] at the function to check the count. The results will be displayed. 6 Confirm the count and press [Close]. 7 Press [Execute] of Counter Reset to reset the counter. 8 Press [Yes] on the screen to confirm the reset. The counter is reset. Check FAX Transmission Time: FAX Transmission Pages: 4 00:00:10 Counter Reset: Execute Close 08/08/2009 Status 10:10 Each Job Accounting/Resetting the Counter This counts the number of pages for each account and resets the counts by account. Use the procedure below to display and reset the counter. User Login/Job Accounting - Each Job Accounting 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting and [Check] of Each Job Accounting. 5 Select the account to check the count. Maintain a separate counter for each account (department). Sort Account Name Name Account ID Others Search(Name) Search(ID) 䋱/䋱 Other Account NOTE: Select [Name] or [ID] from the Sort pull-down menu to sort the account names. Press [Search(Name)] or [Search(ID)] to search by account name or account ID. 6 Detail Press [Detail]. Close Status 11-24 08/08/2009 10:10 OPERATION GUIDE Management Account: Printed Pages: Scanned Pages: Check FAX Transmission Pages: Press [Check] at the function to check the count. The results will be displayed. 8 Confirm the count and press [Close]. 9 Press [Execute] of Counter Reset to reset the counter. Check FAX Transmission Time: 2(20) 7 0:00:10 Counter Reset: 10 Press [Yes] on the screen to confirm the reset. The Execute counter will be reset. Close 08/08/2009 Status 10:10 Counting by Paper Size This counts the number of pages by paper size (e.g. Letter). NOTE: Paper size is available in five types, - 1 to 5. These types are specified in accounting reports. Refer to Printing an Accounting Report on page 11-26. In addition to paper size, media type can also be specified (e.g. count the letter-size color paper used). If no media type is specified, usage is counted for all media types of that size. Use the procedure below to count the number of pages. User Login/Job Accounting - Paper Size 1 Select the paper sizes and types to count. Off On A3 A4 A5 B4 B5 Folio Ledger Legal Letter Statement 1 Press the System Menu key. 2 Press [User Login/Job Accounting]. 3 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 4 Press [Next] of Job Accounting Setting, [Next] of Default Setting, [Change] of Count by Paper Size, [Change] of Paper Size 1 to 5 and then [On]. 5 Select the paper size. 6 Press [Media Type] to specify media type. 7 Select the media type and press [OK]. 8 Press [Close]. Plain Media Type Cancel Status OPERATION GUIDE OK 08/08/2009 10:10 11-25 11 Management Printing an Accounting Report Total pages counted at all relevant accounts can be printed as an accounting report. Reports have different formats depending on how the count of copiers and printers is administered. When Split is selected for Managing the Copier/Printer Count ACCOUNT.REPORT xxxxx Firmware Version For the count by paper size, the report will be printed by size. Use the procedure below to print a job accounting report. 11-26 1 Check that Letter or A4 paper is loaded in the cassette. 2 Press the System Menu key. 3 Press [User Login/Job Accounting]. 4 If user login administration is disabled, the user authentication screen appears. Enter your login user name and password and then press [Login]. For this, you need to login with administrator privileges. Refer to Adding a User on page 11-5 for the default login user name and password. 5 Press [Next] of Job Accounting Setting and then [Print] of Print Accounting Report. 6 Press [Yes] on the screen to confirm the printing. OPERATION GUIDE Management Unknown Account ID Jobs The behavior of the machine when it receives a job from unknown account ID (i.e. unsent ID) can be specified. Refer to Unknown login user name Job on page 11-9 for details. Checking and Printing Counter Press the Counter key to check the number of sheets printed and scanned. Counter Printed Pages Copy Black&White: Printer 300 FAX 600 Total 100 You can check the number of pages printed in each paper size by pressing [Printed Pages by Paper Size]. 1000 Scanned Pages Copy Originals: Print Status Page FAX 300 Others 100 Total 1000 Printed Pages by Paper Size Status 1400 Close 08/08/2009 10:10 Data Security Kit Operations Installing the optional Data Security Kit adds [Data Security] on the System Menu. Refer to the Data Security Kit (E) OPERATION GUIDE on the bundled CD-ROM for descriptions of the [Data Security] options and the procedures for using them. 11 OPERATION GUIDE 11-27 Management 11-28 OPERATION GUIDE Appendix • • • • • Optional Equipment ...............................................................Appendix-2 Character Entry Method.......................................................Appendix-10 Paper ...................................................................................Appendix-13 Specifications .......................................................................Appendix-21 Glossary...............................................................................Appendix-27 OPERATION GUIDE Appendix-1 Optional Equipment Overview of Optional Equipment The following optional equipment is available for the machine. Document Processor Document Processor (Dual scan DP) Document Table Job Separator 3,000 Sheet Document Finisher Built-in Finisher Document Finisher Appendix-2 Paper Feeder 3,000 Sheet Paper Feeder OPERATION GUIDE Key Counter DP FAX Kit Expansion Memory OPERATION GUIDE Appendix-3 Document Processor Automatically scans originals. Also you can perform duplex copying and split copying. For document processor operation, refer to Loading Originals in the Document Processor on page 2-32. Paper Feeder Two additional cassettes identical to the printer’s double cassettes can be installed in the printer. Paper capacity and loading method are the same as Cassettes 1 and 2. NOTE: Left cover 4 is located on the left side of the paper feeder for use in clearing paper jams. 3,000 Sheet Paper Feeder In addition to the printer's cassettes, you can also install an optional 3,000 sheet paper feeder capable of holding up to 3,000 sheets of A4 or B5 paper. NOTE: The 3,000 sheet paper feeder features a removable cover on the left side of the feeder (left cover 4) for removing paper when a paper jam occurs. Document Finisher The document finisher holds a large quantity of finished copies. The finisher offers a convenient means of sorting. Sorted finished copies may also be stapled. For further details, refer to the document finisher Operation Guide. 3,000 Sheet Document Finisher This is a large-capacity document finisher capable of holding large print runs and of separating and offsetting multiple copies of a printout into individual copies. It can also staple or hole-punch (optional) the offset printouts. For details, refer to the 3,000 Sheet Document Finisher Operation Guide. A mail box and folding unit are also available as options. Appendix-4 OPERATION GUIDE Built-in Finisher The built-in finisher holds a large quantity of finished prints. The finisher offers a convenient means of sorting. Sorted finished prints may also be stapled. 2 1 1. Finisher tray 2. Finisher process tray The finisher tray serves as an output tray of sorted prints. Extend the auxiliary tray to sort Ledger, Legal, Letter, Letter-R, A3, B4, A4, A4-R, B5 or Folio prints. Adding Staples 1 OPERATION GUIDE Pull to open the stapler front cover. Appendix-5 Appendix-6 2 Pull out the staple holder. 3 Remove the empty staple case from the staple holder. 4 Holding the staple holder in your left hand and a new staple case in your right hand, insert the staple case into the staple holder in the direction of the arrow. 5 Insert the staple case fully as far as it will go. Pull to remove the paper tape wound on the staple case. OPERATION GUIDE 6 Insert the staple holder into the slot of the staple unit again. When fully inserted, the staple holder locks with a clicking sound. 1 Pull out the staple holder referring to steps 1 and 2 of Adding Staples. 2 Holding the knob A on the face plate of the staple holder, lift the face plate. 3 Clear the staple jammed in the cartridge end (staple-loaded side). 4 Lower the face plate of the staple holder. 5 Insert the face plate back in place. When fully inserted, the face plate locks with a clicking sound. Clearing Staple Jams A OPERATION GUIDE Appendix-7 6 After lifting the staple unit slightly, lower it and insert it again into its place. 7 Close the stapler front cover. Job Separator Separate paper according to output tray for easier sorting. Specify as the output tray for copy or print jobs. Or, specify as the default output tray for printing from the copy or Document Box screen, printing from the PC, and printing of the received fax data. There is a paper indicator in the front of the machine that shows whether there is paper in the Job Separator. CAUTION: Note that some paper types have a tendency to curl and may jam in the paper eject unit. If the ejected paper slips or stacks unevenly, turn the paper in the cassette over and try again. NOTE: • To ensure that paper is delivered to the Job Separator, select the output destination or change the default setting. (For details, refer to the Paper Output on page 8-14.) • When removing paper from the Job Separator, pull it out at an angle. Key Counter Use the key counter to monitor machine usage. The key counter offers a convenient solution for centralized management of copy volume for different departments in a large company. Inserting the Key Counter Insert the key counter securely into the key counter slot. NOTE: When the key counter function is activated, copies can only be made when a key counter is inserted. If the key counter is not inserted, Insert key counter. will be displayed. Appendix-8 OPERATION GUIDE FAX Kit By installing the FAX kit, fax send/receive is enabled. Also, it is possible to use it as a network fax, by using it with a computer. When two FAX kits are installed, the units can be connected to two different telephone lines which will enable quicker message transmission to a number of recipients. If one of the lines is dedicated to receiving, the busy line time can be reduced. For further details, refer to Fax Kit Operation Guide. Expansion Memory Image storage memory (128 MB) that allows the machine to receive more pages of incoming faxed originals. Expansion memory should only be installed or removed by the service representative. Data Security Kit The Data Security Kit overwrites all unnecessary data in the storage area of the hard disk so that it cannot be retrieved. The Data Security Kit encrypts data before storing it in the hard disk. It guarantees higher security because no data cannot be decoded by ordinary output or operations. Printed Document Guard Kit This prevents the unauthorized copying and/or transmission of documents that contain important confidential or personal information. When a document is printed from a computer, this feature imprints a special pattern on the document. When anyone attempts to copy or send that document on this machine, the machine detects the pattern and protects the information by printing the document in blank, prohibiting transmission. Document Table Place original or other documents when using the machine. It has a drawer to accommodate clips. OPERATION GUIDE Appendix-9 Character Entry Method To enter characters for a name, use the on-display keyboard in the touch panel following the steps as explained below. NOTE: QWERTY, QWERTZ and AZERTY are available as keyboard layouts the same as a PC keyboard. Press the System Menu key, [Common Settings] and then [Change] of Keyboard Layout to choose desired layout. QWERTY layout is used here as an example. You may use another layout following the same steps. Entry Screens Lower-case Letter Entry Screen 2 1 Use the keyboard to enter. Limit: 128 characters Input: 0 characters Backspace 1 2 q 3 w a 6 4 e s z r d x Upper-case 5 t f c 7 y g v Lower-case 6 u h b 8 i j n No./Symbol 9 0 o k m p l , ! [ ] / OK 08/08/2009 Appendix-10 Display/Key 8 5 Space Cancel No. \ : Status 7 4 ^ ; . 3 9 10 10:10 11 Description 1 Display Displays entered characters. 2 Limit Display Displays maximum number of characters. 3 Cursor Key Press to move the cursor on the display. 4 [Backspace] Press to delete a character to the left of the cursor. 5 Keyboard Press a character to enter. 6 [Upper-case] Press to use upper-case letters. 7 [Lower-case] Press to use lower-case letters, 8 [No./Symbol] Press to enter numbers and symbols. 9 [Space] Press to insert a space. OPERATION GUIDE No. Display/Key Description 10 [Cancel] Press to cancel entered characters and return to the screen before the entry. 11 [OK] Press to finalize entry and return to the screen before the entry. Upper-case Letter Entry Screen Use the keyboard to enter. Limit: 128 characters Input: 0 characters Backspace ! @ Q # W A S Z Upper-case $ E % R D X F C Lower-case ^ T G V & Y H B * U J N ( I ) O K M No./Symbol L < _ P : > + { } | " ? Space Cancel OK 08/08/2009 Status 10:10 Number/Symbol Entry Screen Use the keyboard to enter. Limit: 128 characters Input: 0 characters Backspace 1 2 3 4 5 6 7 8 9 0 ! " # $ % & ’ ( ) * + , - . / : ; < > ? @ [ \ ] ^ _ ` { | } Upper-case Lower-case No./Symbol Space Cancel 12 OPERATION GUIDE Display/Key [ OK 08/08/2009 Status No. 12 ]/[ ] 10:10 Description To enter a number or symbol not shown in the keyboard, press the cursor key and scroll the screen to view other numbers or symbols to enter. Appendix-11 Entering Characters Follow the steps shown below to enter List A-1 for example. 1 Press [Upper-case]. 2 Press [L]. The letter L is shown on the display. 3 Press [Lower-case]. 4 Press [i], [s], [t] and [Space]. 5 Press [Upper-case]. 6 Press [A]. 7 Press [No./Symbol]. 8 Press [ ] or [ ] repeatedly to view the keyboard containing [-] and [1]. 9 Press [-] and [1]. Use the keyboard to enter. Limit: 128 characters Input: 1 characters L Backspace ! @ Q # W A $ E S Z % R D X T F C & Y G V Lower-case Upper-case ^ * U H B ( I J N ) O K M _ P L < + { : > } | " ? Space No./Symbol Cancel OK 08/08/2009 Status 10:10 Use the keyboard to enter. Limit: 128 characters Input: 4 characters List Backspace 1 2 q 3 w a 4 e s z r d x Upper-case 5 t f c 7 y g v Lower-case 6 u h b 8 i j n 0 o k m No./Symbol 9 p l , ! [ ; . ` ] \ ’ / @ _ Space Cancel OK 08/08/2009 Status 10:10 Use the keyboard to enter. Limit: 128 characters Input: 8 characters List_A-1 Backspace 1 2 3 $ % & ; < | } Upper-case 4 5 6 7 8 9 0 ! " # ’ ( ) * + , - . / : > ? @ [ \ ] ^ _ ` { Lower-case No./Symbol Space Cancel Status OK 08/08/2009 10:10 10 Check that the entry is correct. Press [OK]. Appendix-12 OPERATION GUIDE Paper This section explains the paper sizes and types that can be used in the paper source. Cassettes and the optional paper feeder Supported types Plain paper (60 to 105 g/m2) Recycled paper (60 to 105 g/m2) Supported paper sizes Ledger, Legal, Letter, Letter-R, Statement, A3, B4, A4, A4-R, B5, B5-R, A5-R, Oficio II, 8.5 × 13.5", Folio, 8K, 16K, 16K-R No. of sheets 500 (80g/m2) Optional 3,000 sheet paper feeder Supported types Plain paper (60 to 105 g/m2) Recycled paper (60 to 105 g/m2) Supported paper sizes Letter, A4, B5 No. of sheets 3,000 (80g/m2) Multi Purpose tray (MP tray) Supported types Plain paper (45 to 160 g/m2) Recycled paper (45 to 160 g/m2) Colored paper (45 to 160 g/m2) Supported paper sizes Ledger, Legal, Letter, Letter-R, Executive-R, Statement, A3, B4, A4, A4-R, B5, B5-R, A5-R, B6-R, A6-R, Oficio II, 8.5 × 13.5", 8K, Folio, 16K, 16K-R No. of sheets 200 (80g/m2) 130 (120g/m2) 100 (160g/m2) 50 (200g/m2) Other sizes: Portrait - 3 7/8 to 11 5/8" or 98 to 297 mm Landscape - 5 7/8 to 17" or 148 to 432 mm Postcards Oufuku Hagaki (return postcard) Postcards (100 × 148 mm) Return postcard (148 × 200 mm) Postcards:80 Return postcard:80 Envelopes Envelope DL, Envelope C5, Envelope C4, Envelope #10 (Commercial #10), Envelope #9 (Commercial #9), Envelope #6 (Commercial #6 3/4), Monarch, ISO B5, Youkei 2, Youkei 4 Other sizes: Portrait - 3 7/8 to 11 5/8" or 98 to 297 mm Landscape - 5 7/8 to 17" or 148 to 432 mm 20 Transparency (OHP film) Letter, Letter-R, A4, A4-R 25 OPERATION GUIDE Appendix-13 Basic Paper Specifications This machine is designed to print on standard copy paper as used in regular ('dry') copiers and page printers such as laser printers. It also supports a variety of other types of paper that conform to the specifications given in this appendix. Be careful when choosing paper. Paper unsuitable for the machine may cause jams or may be wrinkled. Supported Paper Use standard copy paper for regular copiers or laser printers. The printing quality will be affected by the quality of paper. Poor quality paper may result in unsatisfactory output. Basic Paper Specifications The following table lists the specifications of paper that is supported with this machine. Refer to the subsequent sections for further details. Criteria Weight Specifications Cassettes: 60 to 105 g/m2 Multi purpose tray: 45 to 160 g/m2 Thickness 0.086 to 0.110 mm Dimensional accuracy ±0.7 mm Squareness of corners 90° ±0.2° Moisture content 4 to 6% Grain direction Long grain (paper supply direction) Pulp content 80% or more NOTE: Some recycled paper does not meet requirements for use with this machine as listed in the Basic Paper Specifications shown below, such as moisture or pulp content. For this reason, we recommend purchasing a small amount of recycled paper as a sample for testing prior to use. Choose recycled paper that gives the best printing results and contains low levels of paper dust. We are not responsible for the problems occurred from the use of paper that does not conform to our specifications. Choosing the Appropriate Paper This section describes guidelines for choosing paper. Condition Avoid using paper with bent corners or that is curled, dirty, or torn. Do not use paper that has a rough surface or paper fiber lint, or that is especially delicate. Use of paper in any of these conditions will not only deliver poor Appendix-14 OPERATION GUIDE copies but may also cause jams and shorten the useful life of the machine. Choose paper with a smooth and even surface; however, avoid paper with a treated surface as it may damage the drum or fusing unit. Ingredient Do not use paper such as paper that has been surface-treated or paper that contains plastic or carbon. These paper may produce harmful fumes from the heat of printing and may damage the drum. Be sure to use the standard paper that contains at least 80% pulp, i.e., not more than 20% of the total paper content consists of cotton or other fibers. Supported Paper Sizes Paper of the following sizes is supported by the machine. Measurements in the table take into account a ±0.7 mm dimensional accuracy for length and width. Corner angles must be 90° ± 0.2°. Multi Purpose Tray Cassette or Multi Purpose Tray A6-R (105 × 148 mm) A3 (297 × 420 mm) B6-R (128 × 182 mm) B4 (257 × 364 mm) Hagaki (100×148mm) A4 (297 × 210 mm) Oufuku Hagaki (148 × 200 mm) A4-R (210 × 297 mm) Executive (7 1/4 ×10 1/2") B5 (257 × 182 mm) Envelope DL (110 × 220 mm) B5-R (182 × 257 mm) Envelope C5 (162 × 229mm) A5-R (148 × 210 mm) Envelope C4 (229 × 324mm) Folio (210 × 330 mm) ISO B5 (176 × 250 mm) Ledger Envelope #10 (Commercial #10) (4 1/8 × 9 1/2") Legal Envelope #9 (Commercial #9) (3 7/8 × 8 7/8") Letter Envelope #6 (Commercial #6 3/4) (3 5/8 × 6 1/2") Letter-R Envelope Monarch (3 7/8 ×7 1/2") Statement-R Youkei 2 (114 × 162 mm) Oficio II Youkei 4 (105 × 235 mm) 8.5 × 13.5" Size Entry (98 × 148 to 297 × 432 mm) 8K (273 × 394 mm) 16K (273 × 197 mm) 16K-R (197 × 273 mm) OPERATION GUIDE Appendix-15 Smoothness The paper surface should be smooth. With paper that is too smooth and slippery, several sheets may accidentally be supplied at once, causing jams. Basis Weight In countries that use the metric system, basis weight is the weight in grams of one sheet of paper one square meter in area. In the United States, basis weight is the weight in pounds of one ream (500 sheets) of paper cut to the standard size (or trade size) for a specific grade of paper. Paper that is too heavy or too light may be supplied incorrectly or cause paper jams, which may cause excessive wear of the machine. Mixed paper weight (i.e., thickness) may cause several sheets to be supplied at once accidentally and may also cause blurring or other printing problems if the toner fails to adhere correctly. The recommended basis weight is between 60 and 163 g/m2 for the cassettes and between 60 to 220 g/m2 for the multi purpose tray. Thickness Avoid using paper that is too thick or thin. Signs that paper may be thin include frequent problems with paper jams or with several sheets being supplied at once. Paper jams may also indicate that the paper is too thick. The proper thickness is between 0.086 and 0.110 mm. Moisture Content Paper moisture content is the ratio of moisture to dryness expressed as a percentage. Moisture affects how the paper is supplied, the electrostatic changeability of the paper, and how the toner adheres. Paper moisture content varies depending on the relative humidity in the room. High relative humidity causes paper to become damp, making the edges expand so it appears wavy. Low relative humidity causes paper to lose moisture, making the edges tighten and weakening print contrast. Wavy or tight edges may cause the paper to slip when it is supplied. Try to keep the moisture content between 4 to 6%. To maintain the right level of moisture content, bear in mind the following considerations. • Store paper in a cool, well-ventilated place. • Store paper flat and unopened in the package. Once the package is opened, reseal it if the paper is not to be used for a while. • Store paper sealed in the original package and box. Put a pallet under the carton to keep it raised above the floor. Especially during rainy seasons keep the paper a sufficient distance away from wooden or concrete floors. • Before using paper that has been stored, keep it at the proper moisture level for at least 48 hours. • Do not store paper where it is exposed to heat, sunlight, or dampness. Other Paper Specifications Porosity: The density of the paper fibers Stiffness: Paper must be stiff enough or it may buckle in the machine, causing jams. Appendix-16 OPERATION GUIDE Curl: Most paper naturally tends to curl after the package is opened. When paper passes through the fixing unit, it curls upward slightly. To deliver flat printouts, load the paper so that the curl faces towards the bottom of the paper tray. Static electricity: During printing, paper is electrostatically charged so that the toner adheres. Choose paper that can be discharged quickly so that copies do not cling together. Whiteness: Paper whiteness affects print contrast. Use whiter paper for sharper, brighter copies. Quality: Machine problems may occur if sheet sizes are not uniform or if corners are not square, edges are rough, sheets are uncut, or edges or corners are crushed. In order to prevent these problems, be especially careful when you cut the paper yourself. Packaging: Choose paper that is properly packaged and stacked in boxes. Ideally, the packaging itself should have been treated with a coating to inhibit moisture. Specially treated paper: We do not recommend printing onto the following types of paper, even if it conforms to the basic specifications. When you use these kinds of paper, purchase a small amount first as a sample to test. • Glossy paper • Watermarked paper • Paper with an uneven surface • Perforated paper Special Paper This section describes printing onto special paper and print media. The following paper and media can be used. • Transparencies • Preprinted paper • Bond paper • Recycled paper • Thin paper (from 60 g/m2 to 64 g/m2 or less) • Letterhead • Colored paper • Prepunched paper • Envelopes • Cardstocks (Hagaki) • Thick paper (from 106 g/m2 to 200 g/m2 or less) • Labels • High-quality paper When using these paper and media, choose that are designed specifically for copiers or page printers (such as laser printers). Use the multi purpose tray for transparencies, thick paper, envelopes, cardstocks, and label paper. OPERATION GUIDE Appendix-17 Choosing Special Paper Although special paper that meets the following requirements can be used with the machine, print quality will vary considerably due to differences in the construction and quality of special paper. Thus, special paper is more likely than regular paper to cause printing problems. Before purchasing special paper in volume, try testing a sample to ensure the print quality is satisfactory. General precautions when printing onto special paper are given below. Note that we are not responsible for any harm to the user or damage to the machine caused by moisture or specifications of special paper. Select a cassette or multi purpose tray for special paper. Transparencies Transparencies must be able to withstand the heat of printing. Transparencies must meet the following conditions. Criteria Specifications Heat resistance Must withstand at least 190°C Thickness 0.100 to 0.110 mm Material Polyester Dimensional accuracy ±0.7 mm Squareness of corners 90° ±0.2° To avoid problems, use the multi purpose tray for transparencies and load transparencies with the long side facing the machine. If transparencies jam frequently at output, try pulling the leading edge of sheets gently as they are ejected. Hagaki Burrs Burrs Before loading Hagaki into the multi purpose tray, fan them and align the edges. If the Hagaki paper is curled, straighten it before loading. Printing onto curled Hagaki may cause jams. Use unfolded Oufuku Hagaki (available at post offices). Some Hagaki may still have rough edges developed by a paper cutter on the back side. Remove any such rough edges by placing the Hagaki on a flat surface and rubbing the edges gently a few times with a ruler. Envelopes Use the multi purpose tray for envelopes. Due to the structure of envelopes, printing evenly over the entire surface may not be possible in some cases. Thin envelopes in particular may be wrinkled by the machine in some cases as they pass through. Before purchasing envelopes in volume, try testing a sample to ensure the print quality. Storing envelopes for a long period may cause them to become wrinkled. Thus, keep the package sealed until you are ready to use them. Appendix-18 OPERATION GUIDE Keep the following points in mind. Do not use envelopes with exposed adhesive. In addition, do not use the type of envelope in which the adhesive is exposed after the top layer is peeled off. Serious damage may be caused if the paper covering the adhesive comes off in the machine. Do not use envelopes with certain special features. For example, do not use envelopes with a grommet for winding a string to close the flap or envelopes with an open or film-covered window. If paper jams occur, load fewer envelopes at once. To prevent paper jams when printing onto multiple envelopes, do not allow more than ten envelopes remain in the output tray at once. Thick Paper Before loading thick paper in the multi purpose tray, fan it and align the edges. Some thick paper may still have rough edges developed by a paper cutter on the back side. Remove any such rough edges just as with Hagaki by placing the paper on a flat surface and rubbing the edges gently a few times with a ruler. Printing onto paper with rough edges may cause jams. NOTE: If the paper is not supplied correctly even after it is smoothed, load the paper in the multi purpose tray with the leading edge raised a few millimeters. Label Be sure to feed labels from the multi purpose tray. For selecting labels, use extreme care so that the adhesive may not come in direct contact with any part of the machine and that the labels are not easily peeled from the carrier sheet. Adhesives that stick to the drum or rollers and peeled labels remaining in the machine may cause a failure. When printing onto labels, you must be liable for the print quality and possible trouble. Top sheet Adhesive layer Carrier sheet Labels consist of three layers as shown in the illustration. The adhesive layer contains materials that are easily affected by the force applied in the machine. The carrier sheet bears the top sheet until the label is used. This composition of labels may cause more problems. The label surface must be covered completely with the top sheet. Gaps between labels may cause peeling of labels, resulting in a serious failure. OPERATION GUIDE Appendix-19 Some label paper has large margins on the top sheet. When using such paper, do not peel these margins from the carrier sheet before completing output. Allowed Not allowed Top sheet Carrier sheet Use label paper that conforms to the following specifications. Item Specifications Top sheet weight 44 to 74 g/m² Basis weight (overall paper weight) 104 to 151 g/m² Top sheet thickness 0.086 to 0.107 mm Overall paper thickness 0.115 to 0.145 mm Moisture content 4 to 6 % (composite) Colored Paper Colored paper must conform to the specifications listed on the page 2 of the Appendix. In addition, the pigments in the paper must be able to withstand the heat of printing (up to 200°C or 392°F). Preprinted Paper Preprinted paper must conform to the specifications listed on the page 2 of the Appendix. The colored ink must be able to withstand the heat of printing. It must be resistant to silicone oil as well. Do not use paper with a treated surface such as glossy paper used for calendars. Recycled Paper Recycled paper must conform to the specifications listed on the page 2 of the Appendix; however, its whiteness may be considered separately. NOTE: Before purchasing recycled paper in volume, try testing a sample to ensure that the print quality. Appendix-20 OPERATION GUIDE Specifications NOTE: Specifications are subject to change without notice. Machine Description Item 42 ppm model 52 ppm model Type Desktop Printing Method Electrophotography by semiconductor laser, tandem drum system Supported Original Types Sheet, Book, 3-dimensional objects (maximum original size: 11 × 17"/A3) Original Feed System Fixed Paper Weight Cassette 1, 2 60 to 105 g/m2 Multi Purpose Tray 45 to 200 g/m2 Cassette 1, 2 Plain, Rough, Vellum, Recycled, Preprinted, Bond, Color (Colour), Prepunched, Letterhead, High Quality, Custom 1 to 8 (Duplex: Same as Simplex) Multi Purpose Tray Plain, Transparency (OHP film), Rough, Vellum, Labels, Recycled, Preprinted, Bond, Cardstock(Hagaki), Color (Colour), Prepunched, Letterhead, Thick, Envelope, High Quality, Custom 1 to 8 Cassette 1, 2 Maximum: 11 × 17"/A3 (Duplex: 11 × 17"/A3) Minimum: 5 1/2 × 8 1/2"/A5R (Duplex: 5 1/2 × 8 1/2"/A5-R) Multi Purpose Tray Maximum: 11 × 17"/A3 Minimum: 5 1/2 × 8 1/2"/A6-R Paper Type Paper Size Zoom Level Manual mode: 25 to 400%, 1% increments Auto mode: Preset Zoom Printing Speed A4/Letter 42 sheets/min A4-R/Letter-R 27 sheets/min A3/Ledger 23 sheets/min B4/Legal 23 sheets/min B5 42 sheets/min B5-R 22 sheets/min A5-R/A6-R 16 sheets/min First Print Time (A4, feed from Cassette) 3.9 seconds or less Warm-up Time (22°C/71.6°F, 60%) Power on 30 seconds or less Sleep 15 seconds or less OPERATION GUIDE A4/Letter 52 sheets/min A4-R/Letter-R 31 sheets/min A3/Ledger 26 sheets/min B4/Legal 26 sheets/min B5 52 sheets/min B5-R 24 sheets/min A5-R/A6-R 18 sheets/min Appendix-21 Description Item 42 ppm model Paper Capacity Output Tray Capacity Cassette 500 sheets (80 g/m2) Multi Purpose Tray 200 sheets (80 g/m2) Top tray 250 sheets (80 g/m2) with built-in finisher 150 sheets (80 g/m2) with optional job separator 250 sheets (80 g/m2) Continuous Copying 1 to 999 sheets Image Write System Semiconductor laser and electrophotography Main Memory Standard 2048 MB Maximum 2048 MB Hard Disk Interface 160 GB Standard USB Interface Connector: 1 (USB Hi-Speed) USB memory slot: 2 (Full-Speed USB) Network interface: 1 (10 BASE-T/100 BASE-TX) Option KUIO/W slot: 2 Resolution Operating Environment 52 ppm model 600 × 600 dpi Temperature 10 to 32.5°C/50 to 90.5°F Humidity 15 to 80% Altitude 2,500 m/8,202 ft maximum Brightness 1,500 lux maximum Dimension (W × D × H) 23 9/16 × 25 7/16 × 29 5/16" (Main unit only) 599 × 646 × 745 mm Weight (without toner container and waste toner box) 187 lb/85 kg Space Required (W × D) 29 5/8 × 25 7/16" (Using multi purpose tray) 753 × 646 mm Power Source 120 V AC, 60 Hz, 12 A/220 to 240 V AC, 50 Hz, 6.3 A Options Document processor, Paper feeder, 3,000 sheet paper feeder, Document finisher, 3,000 sheet document finisher, Job separator, Built-in finisher, Key counter, FAX kit, Expansion memory, Data Security Kit, Printed Document Guard Kit Appendix-22 OPERATION GUIDE Printer Item Description Printing Speed Same as Copying Speed. First Print Time (A4, feed from Cassette) 4.8 seconds or less Resolution 600 dpi Operating System Windows 2000 (Service Pack 2 or later), Windows XP, Windows Server 2003, Windows Vista, Apple Macintosh OS 10.x Interface USB Interface Connector: 1 (USB Hi-Speed) Network interface: 1 (10 BASE-T/100 BASE-TX) Standard Page Description Language PRESCRIBE Scanner Item Description Operating System Windows 2000 (Service Pack 2 or later), Windows XP, Windows Vista System requirements CPU: 600Mhz or higher RAM: 128MB or more Resolution 600 dpi, 400 dpi, 300 dpi, 200 dpi, 200 ×100 dpi, 200 × 400 dpi (Resolution in FAX mode included) File Format TIFF (MMR/JPEG compression), JPEG, XPS, PDF (MMR/JPEG compression), PDF (high compression) Scanning Speed *1 1-sided B/W 52 Images/min Interface Ethernet (10 BASE-T/100 BASE-TX) Network Protocol TCP/IP Transmission System PC transmission *1 *2 *3 SMB Scan to SMB FTP Scan to FTP, FTP over SSL E-mail transmission SMTP Scan to E-mail TWAIN scan*2 WIA scan*3 When using the dual scan document processor (except TWAIN and WIA scanning) Available Operating System: Windows 2000 (Service Pack 2 or later), Windows XP, Windows Vista Available Operating System: Windows Vista OPERATION GUIDE Appendix-23 Document Processor (option) Item Description Original Feed Method Automatic feed Supported Original Types Sheet originals Paper Size Maximum: Ledger/A3 Minimum: Statement-R/A5-R Paper Weight 45 to 160 g/m2 Loading Capacity 100 sheets (50 to 80 g/m2) maximum Mixed original sizes (auto selection): 30 sheets (50 to 80 g/m2) maximum Dimensions (W) × (D) × (H) 22 23/32 × 21 × 7 5/64" 577 × 534 × 180 mm Weight Approx. 26 lbs. / Approx. 12 kg Dual scan DP model: Approx. 29 lbs. / Approx. 13 kg Paper Feeder (option) Item Description Paper Supply Method Friction Feed (No. Sheets: 500, 80 g/m2, 2 cassettes) Paper Size Ledger, Legal, Oficio II, 8.5×13.5", Letter, Letter-R, Statement-R, A3, B4, A4, A4-R, B5, B5-R, A5-R, Folio, 8K, 16K, 16K-R Supported Paper Paper weight: 60 - 160 g/m2 Media types: standard, recycled, color Dimensions (W) × (D) × (H) 23 1/32 × 23 15/64 × 12 13/32" 585 × 590 × 315 mm Weight Approx. 57 lbs. / Approx. 26 kg 3,000 Sheet Paper Feeder (option) Item Description Paper Supply Method Friction Feed (No. Sheets: 3,000 (80 g/m2)) Paper Size A4, B5, Letter Supported Paper Paper weight: 60 - 105 g/m2 Media types: standard, recycled, color Appendix-24 OPERATION GUIDE Item Description Dimensions (W) × (D) × (H) 23 × 23 5/8 × 12 23/64" 585 × 600 × 314 mm Weight Approx. 50.71 lbs / Approx. 23 kg Document Finisher (option) Item Description Number of Trays 1 tray Paper Size (Non-stapling) Ledger, Legal, Oficio II, 8.5×13.5", A3, B4, 8K: 500 sheets Letter, Letter-R, A4, A4-R, B5, B5-R, 16K, 16K-R: 1,000 sheets Supported Paper Weight Stapling: 90 g/m2 or less Maximum Sheets for Stapling Ledger, Legal, Oficio II, 8.5×13.5", A3, B4, 8K: 25 sheets Letter, Letter-R, A4, A4-R, 16K: 50 sheets (Paper weight 90 g/m2 or less) Dimensions (W) × (D) × (H) 25 × 20 63/64 × 40 5/16" 634.9 × 533 × 1013.5 mm Weight Approx. 58.42 lbs. / Approx. 26.5 kg 3,000 Sheet Document Finisher (option) Item Description Number of Trays 3 trays Paper Size Tray A (NonStapling) Ledger, Legal, Oficio II, 8.5×13.5", A3, B4, Folio, 8K: 1,500 sheets Letter, Letter-R, A4, A4-R, B5, 16K: 3,000 sheets Tray B Ledger, Legal, Oficio II, 8.5×13.5", A3, B4, Folio, 8K: 100 sheets Letter, Letter-R, Statement-R, A4, A4-R, B5, B5-R, A5R, B6-R, A6-R, 16K, 16K-R : 200 sheets Tray C Letter, Statement-R, A4, B5, A5-R, B6-R, A6-R, 16K: 50 sheets Supported Paper Weight Stapling: 90 g/m2 or less Maximum Sheets for Stapling Ledger, Legal, Oficio II, 8.5×13.5", A3, B4, Folio, 8K: 30 sheets A4, A4-R, B5, Letter, Letter-R, 16K: 50 sheets (Paper weight 90 g/m2 or less) Dimensions (W) × (D) × (H) 27 1/2 × 22 9/16 × 42 13/16" 687 × 573 × 1087mm Weight Approx. 121.3 lbs / Approx. 55 kg OPERATION GUIDE Appendix-25 Job Separator (option) Item Description Number of Trays 1 tray Maximum Sheets 100 sheets (80 g/m2) Paper Size Ledger, Legal, Oficio II, 8.5×13.5", Letter, Letter-R, Executive-R, Statement-R, A3, B4, A4, A4-R, B5, B5-R, A5-R, Folio Paper Type Paper weight: 45 - 160 g/m2 Paper type: plain, recycled, color, thin Dimensions (W) × (D) × (H) 20 13/16 × 18 11/16 × 3 3/16" 530 × 475 × 82 mm Weight 3.3 lbs. or less / 1.5 kg or less Built-in Finisher Item Description Number of Trays 1 tray Paper Size (Non-stapling) Ledger, Legal, A3, B4, Folio: 250 sheets Letter, Letter-R, A4, A4-R, B5: 500 sheets 60 to 80 g/m2 Maximum Sheets for Stapling Ledger, Legal, A3, B4, Folio: 20 sheets Letter, Letter-R, A4, A4-R, B5: 30 sheets (Paper weight 80 g/m2 or less) Dimensions (W) × (D) × (H) 12 3/16 × 16 1/8 × 6 5/16" 310 × 410 ×160 mm Weight 20 lbs. or less / 9 kg or less NOTE: Consult your dealer or service representative for recommended paper types. Appendix-26 OPERATION GUIDE Glossary Accessibility The machine is designed featuring good accessibility even for the elderly and those who are physically challenged or visually impaired. Touch panel characters can be enlarged while the touch panel is adjustable in two angles. AppleTalk AppleTalk, which comes with Apple Computer's Mac OS, is a network protocol. AppleTalk enables file/printer sharing and also enables you to utilize application software that is on another computer on the same AppleTalk network. Auto Form Feed Timeout During data transmission, the machine may sometimes have to wait until receiving the next data. This is the auto form feed timeout. When the preset timeout passes, the machine automatically put paper out. However, no output is performed if the last page has no data to be printed. Auto-IP Auto-IP is a module that enables dynamic IPv4 addresses to be assigned to a device on startup. However, DHCP requires a DHCP server. Auto-IP is a server-less method of choosing an IP address. IP addresses between 169.254.0.0 to 169.254.255.255 are reserved for Auto-IP and assinged automatically. Auto Paper Selection A function to automatically select paper in the same size as original at printing Auto Sleep A mode designed for electrical power saving, activated when the machine is left unused or data transfer for a specific period. In Sleep mode, power consumption is kept to a minimum. Bonjour Bonjour, also known as zero-configuration networking, is a service that automatically detects computers, devices and services on an IP network. Bonjour, because an industry-standard IP protocol is used, allows devices to automatically recognize each other without an IP address being specified or DNS server being set. Bonjour also sends and receives network packets by UDP port 5353. If a firewall is enabled, the user must check that UDP port 5353 is left open so that Bonjour will run correctly. Some firewalls are set up so as to reject only certain Bonjour packets. If Bonjour does not run stably, check the firewall settings and ensure that Bonjour is registered on the exceptions list and that Bonjour packets are accepted. If you install Bonjour on Windows XP Service Pack 2 or later, the Windows firewall will be set up correctly for Bonjour. Default Gateway This indicates the device, such as a computer or router, that serves as the entrance/exit (gateway) for accessing computers outside the network that you are on, When no specific gateway is designated for a destination IP address, data is sent to the host designated as the Default Gateway. OPERATION GUIDE Appendix-27 DHCP (Dynamic Host Configuration Protocol) Dynamic Host Configuration Protocol (DHCP) that automatically resolves IP addresses, subnet masks, and gateway addresses on a TCP/IP network. DHCP minimizes the load of network management employing a large number of client computers because it relieves individual clients including printers from the IP address being assigned. DHCP (IPv6) DHCP (IPv6) is the next-generation of the Internet's Dynamic Host Configuration Protocol and supports IPv6. It extends the BOOTP startup protocol that defines the protocols used for transferring configuration information to hosts on the network. DHCP (IPv6) permits the DHCP server to use its expanded functionality to send configuration parameters to an IPv6 node. Because the network addresses that can be used are allocated automatically, the IPv6 node management workload is reduced in systems where the administrator has to exercise close control over IP address allocation. dpi(dots per inch) A unit for resolution, representing the number of dots printed per inch (25.4 mm). EcoPrint Mode A printing mode that helps save toner. Copies made in this mode are thus lighter than normal. Emulation The function to interpret and execute other printers' page description languages. The machine emulates operation of PCL6, KPDL, and KPDL (automatic). FTP(File Transfer Protocol) A protocol to transfer files on the TCP/IP network, whether the Internet or an intranet. Along with HTTP and SMTP/POP, FTP is now frequently used on the Internet. Grayscale A computer color expression. Displayed images of this sort are typically composed of shades of gray, varying from black at the weakest intensity to white at the strongest, without any other colors. Gray levels are displayed in numerical levels: that is, white and black only for 1 bit; 256 gray levels (including white and black) for 8 bits; and 65,536 gray levels for 16 bits. Help A Help key is provided on this machine's operation panel. If you are unsure of how to operate the machine, would like more information on its functions or are having problems getting the machine to work properly, press the Help key to view a detailed explanation on the touch panel. IP Address An Internet protocol address is a unique number that represents a specific computer or related device on the network. The format of an IP address is four sets of numbers separated by dots, e.g. 192.168.110.171. Each number should be between 0 and 255. Appendix-28 OPERATION GUIDE IPP IPP (Internet Printing Protocol) is a standard that uses TCP/IP networks such as the Internet to enable print jobs to be sent between remote computers and printers.IPP is an extension of the HTTP protocol used to view websites and enables printing to be carried out via routers on printers in remote locations. It also supports the HTTP authentication mechanisms along with SSL server and client authentication as well as encryption. KPDL (Kyocera Page Description Language) Kyocera's PostScript page description language compatible with Adobe PostScript Level 3. Multi Purpose (MP) Tray The paper supply tray on the right side of the machine. Use this tray instead of the cassettes when printing onto envelopes, Hagaki, transparencies, or labels. NetBEUI (NetBIOS Extended User Interface) An interface, developed by IBM in 1985, as an update from NetBIOS. It enables more advanced functions on smaller networks than other protocols such as TCP/IP, etc. It is not suitable for larger networks due to lack of routing capabilities to choose the most appropriate routes. NetBEUI has been adopted by IBM for its OS/2 and Microsoft for its Windows as a standard protocol for file sharing and printing services. NetWare Novell's network management software that is able to run on a variety of operating systems. POP3 (Post Office Protocol 3) A standard protocol to receive E-mail from the server in which the mail is stored on the Internet or an intranet. PostScript A page description language developed by Adobe Systems. It enables flexible font functions and highlyfunctional graphics, allowing higher quality printing. The first version called Level 1 was launched in 1985, followed by Level 2 that enabled color printing and two-byte languages (e.g. Japanese) in 1990. In 1996, Level 3 was released as an update for the Internet access and PDF format as well as gradual improvements in implementation technologies. PPM (prints per minute) This indicates the number of A4 size printouts made in one minute. Printer Driver The software to enable you to print data created on any application software. The printer driver for the machine is contained in the CD-ROM enclosed in the package. Install the printer driver on the computer connected to the machine. RA(Stateless) The IPv6 router communicates (transmits) information such as the global address prefix using ICMPv6. This information is the Router Advertisement (RA). ICMPv6 stands for Internet Control Message Protocol, and is a IPv6 standard defined in the RFC 2463 "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification". OPERATION GUIDE Appendix-29 Send as E-mail A function to send the image data stored in the machine as an E-mail attachment. E-mail addresses can be selected from the list or entered at each time. SMTP (Simple Mail Transfer Protocol) A protocol for E-mail transmission over the Internet or an intranet. It is used for transferring mail between mail servers as well as for sending mail from clients to their servers. Status Page The page lists machine conditions, such as the memory capacity, total number of prints and scans, and paper source settings. Subnet Mask The subnet mask is a way of augmenting the network address section of an IP address. A subnet mask represents all network address sections as 1 and all host address sections as 0. The number of bits in the prefix indicates the length of the network address. The term "prefix" refers to something added to the beginning and, in this context, indicates the first section of the IP address. When an IP address is written, the length of the network address is indicated by the prefix length after a forward slash (/). For example, "24" in the address "133.210.2.0/24". In this way, "133.210.2.0/24" denotes the IP address "133.210.2.0" with a 24-bit prefix (network section). This new network address section (originally part of the host address) made possible by the subnet mask is referred to as the subnet address.When you enter the subnet mask, be sure to set the DHCP setting to Off. TCP/IP (Transmission Control Protocol/Internet Protocol) TCP/IP is a suite of protocols designed to define the way computers and other devices communicate with each other over a network. TCP/IP (IPv6) TCP/IP (IPv6) is based on the current Internet protocol, TCP/IP (IPv4). IPv6 is the next-generation Internet protocol and expands the available address space, which resolves the problem of the lack of addresses under IPv4, while also introducing other improvements such as additional security functionality and the capacity to prioritize data transmission. TWAIN (Technology Without Any Interested Name) A technical specification for connecting scanners, digital cameras, and other image equipment to the computers. The TWAIN compatible devices enable you to process image data on any relevant application software. TWAIN is adopted on a large amount of graphic software (e.g. Adobe Photoshop) and OCR software. USB (Universal Serial Bus)2.0 A USB interface standard for Hi-Speed USB 2.0. The maximum transfer rate is 480 Mbps. This machine is equipped with USB 2.0 for high-speed data transfer. Appendix-30 OPERATION GUIDE WIA (Windows Imaging Acquisition) A function to import images supported after Windows Me/XP from digital cameras and other peripheral devices.This function replaces what TWAIN used to do; the feature is provided as a part of Windows functions and improves ease of operation, so that you import images directly to My Computer without using any application. OPERATION GUIDE Appendix-31 Appendix-32 OPERATION GUIDE Index Index Numerics 1-sided/2-sided Selection 5-10 3,000 sheet document finisher Appendix-4 3,000 sheet paper feeder Appendix-4 A Accessibility 8-77, Appendix-27 Adjusting Density 5-17 Auto 3-7 Manual 3-7 Adjusting the Operation Panel Angle 2-10 Adjustment/Maintenance 8-42 Auto Color Correction 8-45 Color Calibration Cycle 8-46 Copy Density Adjustment 8-42 Correcting Fine Black Lines 8-44 Display Brightness 8-44 Drum Refresh 8-43 Gray Adjustment 8-46 Send/Box Density 8-42 Silent Mode 8-45 System Initialization 8-44 AppleTalk Appendix-27 Setup 2-14 Applications 8-60 Attention Indicator 1-4 Auto Image Rotation 4-32 Auto Paper Selection Appendix-27 Auto Sleep 2-9, Appendix-27 B Background density adjust Send 5-20 Bonjour Appendix-27 Booklet from Sheets 4-19 Left side 4-19 Right side 4-19 Top binding 4-19 Border Erase Copy 4-17 Send 5-23 Bundled Items 2-2 Buzzer 8-3 OPERATION GUIDE C Cassette Loading Paper 2-20 Paper Size and Media Type 8-5 Cassette 1 1-4 Cassette 2 1-4 Caution Labels ix CD-ROM 2-2 Centering 5-6 Changing Language 2-10, 8-2 Character Entry Method Appendix-10 Cleaning Dual scanning area 9-3 Glass Platen 9-2 Original Cover 9-2 Separator 9-4 Slit Glass 9-3 Transfer Roller 9-6 Clip Holder 1-4 Color Background Density Adjust 5-20 Color / Grayscale / Black and White Selection 5-21 Color Profiles 5-32 Color Type 5-31, 8-30 Gray Adjustment 8-46 Color mode 3-6 Color Selection (Send/Store) 8-17 Color type 5-31 Combine Mode 2-in-1 Mode 4-13 4-in-1 Mode 4-13 Page Boundary Lines 4-14 Embedded Web Server 2-16 Connecting LAN Cable 2-5 Power Cable 2-6 USB Cable 2-6 Connection Method 2-3 Continuous Scan Copy 4-31 Index-1 Index Send 5-22 Conventions in This Guide xxvii Copy Appendix-9 Adjusting Density 3-7 Collate Copying 3-13 Duplex Copying 3-11 Offset Copying 3-13 Originals 4-2 Selecting Image Quality 3-8 Setup 8-26 Zoom Copying 3-9 Copy Settings 8-26 Auto % Priority 8-27 Auto Paper Selection 8-26 Border Erase for Back Page 8-26 Paper Selection 8-26 Preset Limit 8-27 Quick Setup Registration 8-28 Reserve Next Priority 8-27 Copying Functions 4-1 Counting the Number of Pages Printed by Paper Size 11-25 Counter 11-27 Each Job 11-24 Printing a Report 11-26 Total Job 11-23 Unknown Account ID Jobs 11-27 Counting the Number of Pages Printed 11-23 Cover Mode 4-21 Custom Box Creating a New Box 6-2 Deleting Documents 6-11 Editing Documents 6-8 Form Overlay 6-7 Join Documents 6-9 Move Documents 6-8 Printing Documents 6-5 Sending Documents 6-6 Storing Documents 6-4 User Privileges 3-40 D Date/Timer 8-47 Auto Error Clear 8-49 Auto Panel Reset 8-48 Auto Sleep 8-49 Index-2 Date Format 8-47 Date/Time 8-47 Setup 8-47 Time Zone 8-48 Default 8-15 Auto Image Rotation 8-21 Border Erase 8-20 Border Erase to Back Page 8-20 Collate/Offset 8-21 Color Selection (Send/Store) 8-17 Color TIFF Compression Settings 8-23 Continuous Scan 8-16 Density 8-18 EcoPrint 8-22 E-mail Subject/Body 8-19 File Format 8-17, 8-18 File Name 8-19 High Comp. PDF Image 8-23 JPEG/TIFF Print 8-24 Margin 8-21 Original Image 8-16 Original Orientation 8-15 PDF/TIFF/JPEG Image 8-22 Repeat Copying 8-23 Scan Resolution 8-16 XPS Fit to Page 8-25 Zoom 8-19 Default Gateway Appendix-27 Default Screen 8-2 Density Adjustment Copy 3-7 Send 5-17 Destination 8-51 Adding 8-51 Adding a contact 8-51 Adding a Group 8-53 Choosing by One Touch Key 3-32 Choosing by Speed Dial 3-32 Choosing from the Address Book 3-30 Editing 8-54 One Touch Key 8-55 Quick No. Search key 3-3 Search 3-31 Sending to Different Types of Destinations (Multi Sending) 3-32 Device 7-16 OPERATION GUIDE Index Canceling FAX Communication 7-18 Checking Status 7-16 Configuring 7-17 Displaying Screen 7-16 USB Memory 7-17 DHCP Appendix-28 DHCP (IPv6) Appendix-28 Document Box 3-33, 6-1 Basic Operation 3-35 Custom Box 3-33, 6-2 Document deletion time 6-3 Form Overlay 6-7 Job Box 3-33, 6-12 Quick Setup Registration 8-32 What is Document Box? 3-33 Document Finisher Appendix-4, Appendix25 Document Guard 8-73 Document Processor Appendix-4, Appendix-24 How to Load Originals 2-33 Loading Originals 2-32 Not Supported Originals 2-32 Part Names 2-32 Supported Originals 2-32 Document Table Appendix-9 Double Copy 4-27 dpi Appendix-28 Duplex 3-11, 8-36 E EcoPrint Mode Appendix-28 Copy 4-13 Print 8-35 E-mail Send as E-mail 3-24 Emulation Appendix-28 Selection 8-34 Energy Star Program xxv Enlarged Display 8-77 Enter E-mail Subject and Body 5-26 Enter key 1-3, 3-3 Entry Body 5-26 Document Name 5-25 File Name 4-35, 5-25 Subject 5-26 OPERATION GUIDE Error Handling 8-12 Error Messages 10-6 Expansion Memory Appendix-9 F File Format 5-12 PDF 5-14 File Name 4-35 File Separation 5-13 Form Overlay 4-22 Storing a Form 6-17 FTP Appendix-28 FTP (Reception) Protocol Detail 8-66 FTP Encrypted TX 5-31 G Glass Platen Cleaning 9-2 GPL xxii Gray Adjustment 8-46 Grayscale 5-21, Appendix-28 Green Knob 1-5 Grounding the Machine xi H Help Appendix-28 Host Name 8-64 HTTP Protocol Detail 8-66 HTTPS Protocol Detail 8-67 I Image Quality Send 5-16 Image repeat copy 4-27 Included Guides 2 Installation Precautions x Interface Block 8-72 Internet Browser 8-58 Interrupt Clear Timer 8-50 Interrupt Copy 3-16 IP Address Appendix-28 IPP Appendix-29 IPP over SSL Protocol Detail 8-67 J Job Index-3 Index Available Status 7-2 Canceling 3-42, 7-13 Checking History 7-9 Checking Status 7-2 Detailed Information 7-7 Detailed Information of Histories 7-10 Details of the Status Screens 7-3 Displaying History Screen 7-9 Displaying Status Screens 7-2 Pause and Resumption 7-13 Reordering 7-14 Sending the Job Log History 7-11 Job Accounting 11-14 Managing the Copier/Printer Counts 11-18 Restricting the Use of the Machine 11-18 Job Box Form Overlay Box 6-17 Private Print/Stored Job Box 6-12 Quick Copy/Proof and Hold Print Box 6-13 Repeat Copy Box 6-15 Job Finish Notice 5-29 Copy 4-34 Send 5-29 K Key Counter Appendix-8 KPDL Appendix-29 L Label Appendix-19 LAN Cable Connecting 2-5 LAN Interface Setup 8-71 LDAP Protocol Detail 8-66 Left Cover 1 1-4 Left Cover 1 Lever 1-4 Left Cover 2 1-4 Legal Information xx Login 3-2, 11-3 Logout 3-2, 11-3 LPD Protocol Detail 8-66 M Main Power Switch 1-6 Management 11-1 Index-4 Job Accounting 11-14 User Login Administration 11-2 Margin/Centering Mode 4-15 Memo Mode 4-25 Mirror Image 4-33 Mixed Sized Originals 4-7 Combinations 4-7 Copy Size 4-9 Send 5-7 Monotype Imaging License Agreement xxiv MP Tray Cleaning 8-47 Multi Purpose (MP) Tray Appendix-29 Paper Size and Media 2-28, 8-6 Multi Purpose Tray 1-6 Multi Sending (Sending to Different Types of Destinations ) 3-32 N Negative Image 4-32 NetBEUI Appendix-29 Protocol Detail 8-66 NetWare Appendix-29 Setup 8-67 Network Preparation 2-12 Setup 8-64 Network Cable 2-4 Connecting 2-5 Network Interface 2-4 O One Touch Key Changing the Registered Information 8-56 Deleting the Registered Information 8-56 Editing 8-55 Open SSL xxii Operation Panel 1-2, 1-4 Option 3,000 sheet document finisher Appendix-4 3,000 sheet paper feeder Appendix-4 Data Security Kit Appendix-9 Document Finisher Appendix-4 Document Processor Appendix-4 Document Table Appendix-9 Expansion Memory Appendix-9 FAX Kit Appendix-9 OPERATION GUIDE Index Job Separator Appendix-8 Key Counter Appendix-8 Overview Appendix-2 Paper Feeder Appendix-4 Option Interface Slot 1-6 Optional Functions 8-75 Orientation Confirmation 8-15 Original Loading in the Document Processor 2-32 Placing on the Platen 2-30 Size xxviii Original Cover 1-4 Cleaning 9-2 Original Orientation Copy 4-10 Document Processor 4-10 Orientation Confirmation 8-15 Send 5-11 Original Placement Indicator Indications and Status 2-33 Original Size Indicator Plates 1-4, 2-30 Original Size Selection Send 5-2 Original SSLeay License xxiii Originals Automatic Detection 8-9 Copy 4-2 Custom 8-4 Setup 8-4 Size Selection 4-2, 5-2 Output Destination 4-12 Output Tray 8-14 P Page Numbering 4-23 Paper Appropriate Paper Appendix-14 Auto Selection 8-9 Before Loading 2-19 Cassette 8-5 Checking the Remaining Amount of Paper 7-15 Custom 8-4 Default Paper Source 8-9 Loading Envelopes 2-24 Loading in the Cassettes 2-20 OPERATION GUIDE Loading in the Multi Purpose Tray 2-22 Multi Purpose Tray 8-6 Paper Source for Cover Paper 8-10 Setup 8-4 Size and Media 2-26, Appendix-13 Special Paper 8-10, Appendix-17 Specifications Appendix-14 Weight 8-7 Paper Feed Unit 1-5 Paper Feeder Appendix-4 Paper Jam 10-15 Cassette 1 10-16 Cassette 2 10-17 Cassettes 3 and 4 10-18 Document Finisher 10-26 Document Processor 10-25 Duplex Unit 10-20 Duplex Unit and Cassette 1 10-21 Inside the Left Covers 1, 2 and 3 10-20 Jam Location Indicators 10-15 Multi Purpose Tray 10-19 Precaution 10-16 Paper Length Guide 2-20 Paper Selection 4-4 Cassette 4-4 Multi Purpose Tray 4-5 Paper Width Guides 2-20 Part Names 1-1 Platen 1-4 Placing Originals 2-30 POP3 Appendix-29 POP3 (E-mail RX) Protocol Detail 8-66 PostScript Appendix-29 Power Cable Connecting 2-6 Power Off 2-8 Power On 2-7 Power Supply xi PPM Appendix-29 Precautions for Use xii Preparation 2-1 Preparing Cables 2-4 Print Job Reordering 3-43 Printed Document Guard Kit Appendix-9 Index-5 Index Printer Setup 8-34 Printer Driver Appendix-29 Printer Settings 8-34 Copies 8-36 CR Action 8-38 Duplex 8-36 EcoPrint 8-35 Emulation 8-34 Form Feed Timeout 8-37 LF Action 8-37 Orientation 8-37 Override A4/Letter 8-35 Paper Feed Mode 8-38 Printing 3-21 Printing from Applications 3-21 Printing Reports/Sending Notice 8-39 Font List 8-39 Network Status Page 8-40 Service Status Page 8-40 Status Page 8-39 Transmission Result Reports 8-40 Priority Override 4-35, 7-14 Product Library 2-2 Programmed Copying 3-46 Editing and Deleting 3-47 Recalling 3-46 Registering 3-46 Punch 3-19 Q Quick No. Search key 1-3, 3-3 Quick Setup Screen 3-43 Changing Registration 3-44, 8-28, 8-29, 832 R RA (Stateless) Appendix-29 Raw Port Protocol Detail 8-67 Receive Indicator 1-4 Repeat Copy 4-36 Maximum Number 4-37 Outputting 4-37 Selecting 4-36 Replacement Toner Container 9-8 Waste Toner Box 9-8 Index-6 Reserve Next 3-15 Reserve Next Priority 8-27 Resolution Appendix-22, Appendix-23 Restarting the System 8-63 S Safety Conventions i Safety Instructions Regarding the Disconnection of Power xvi Scan Resolution 5-18 Default settings 8-16 Scanner Cleaning 8-47 Secure Protocol 8-69 Send File Format 5-12 Image Quality 5-16 Original Size Selection 5-2 Print 5-30 Sending Size Selection 5-3 Setup 8-29 Store 5-30 Sending Send as E-mail 3-24 Send to Folder (FTP) 3-27 Send to Folder (SMB) 3-26 Sending E-mail 2-17 Sending Functions 5-1 Sending Settings 8-29 Color Type 8-30 Quick Setup Registration 8-29 Sending Size Selection 5-3 Sending to Different Types of Destinations (Multi Sending) 3-32 Separator Cleaning 9-4 Setting Date and Time 2-11 Sharpness adjust Copy 4-30 Send 5-19 Shortcuts 3-48 Adding 3-48 Sleep 2-9 Slit Glass 1-4 Cleaning 9-3 SMTP Appendix-30 SMTP (E-mail TX) Protocol Detail 8-66 OPERATION GUIDE Index SNMP Protocol Detail 8-66 SNMPv3 Protocol Detail 8-66 Solving Malfunctions 10-2 Specifications Built-in Finisher Appendix-26 Document Finisher Appendix-25 Document Processor Appendix-24 Job Separator Appendix-26 Machine Appendix-21 Paper Feeder Appendix-24 Printer Appendix-23 Scanner Appendix-23 Specifying Destination 3-29, 3-30 Status / Job Cancel 7-1 Status Page 8-39, Appendix-30 Subnet Mask Appendix-30 Supplies Checking the Remaining Amount 7-15 Switching the Language 2-10, 8-2 Switching Unit of Measurement 8-11 Symbols i System Initialization 8-63 System Menu 8-1 T TCP/IP Appendix-30 TCP/IP (IPv4) Setup 2-12 TCP/IP (IPv6) Appendix-28 Setup 8-64 Toner Container Checking the Remaining Amount of Toner 7-15 Replacement 9-8 Trade Names xxi Transfer Roller Cleaning 9-6 TWAIN Appendix-30 U USB Appendix-30 OPERATION GUIDE USB Cable Connecting 2-6 USB Interface 1-6, 2-4 USB Memory Printing Documents 6-20 Removing 6-21 Saving Documents 6-22 User Login Administration 11-2 Adding 11-5 Changing Properties 11-7 Enabling/Disabling 11-2 Group Authorization Settings 11-10 Login 11-3 Logout 11-4 Unknown login user name Job 11-9 W Waste Toner Box 1-5 Replacement 9-8 Status 7-15 WIA Appendix-31 WSD Print Setup 8-68 WSD Scan 5-27 Setup 8-68 X XPS File formats 5-12, 8-17 Printing documents stored in Removable USB Memory 6-20 Saving documents to Removable USB Memory 6-22 Z Zoom Copying Auto Zoom 3-9 Manual Zoom 3-9 Preset Zoom 3-9 XY Zoom 3-10 Zoom Mode Copy 5-5 Send 5-5 Index-7 Index Index-8 OPERATION GUIDE We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. E1 MEMO MEMO UTAX GmbH, Ohechaussee 235, 22848 Norderstedt, Germany
advertisement