Chiayo DCR-511 Operation Manual

ISO 9001:2008

REGISTERED

ISO

14001

ISO 14001

REGISTERED

OHSAS

18001

OHSAS 18001

Green Product

DCT-511

DCR-511

2.4G DIGITAL TWO-WAY TOUR GUIDE SYSTEM

OPERATION MANUAL

DCT-511 Mini transmitter

Parts and functions

1. Antenna 1

2. Mute

3. Volume control

4. Power/frequency synchronizing

5. MIC-MIX-AUX IN mode switch

6. Aux input(Ø 3.5mm)

7. Power indicator

2

3

5

8. Mute indicator

9. Earphone jack (Ø 3.5mm)

10. Mini USB charging port

11. Reset

7 8 9

4 6

10

11

Instructions

1. Power ON/OFF: To turn on the transmitter, press the power button for one second and the power indicator will turn green. It turns red when battery is low or during charging. To turn off the transmitter, press and hold the power button for about 3 seconds and the indicator light will go off.

2. To activate or cancel muting, press Mute button

3. To add music as background music, just input your audio signal to AUX IN In a museum tour, you may also input the respective prerecorded introductions for various galleries.

4. Audio mode switch: If using only earphone, please switch to . For only music, please switch to . To use earphone and play music simultaneously, please switch to the middle.

5. Charging: During charging, the red light will go off once the battery is full. The charging process takes approximately four hours. Charging can be done by either mini USB or the dedicated charging box.

-1-

ISO 9001｜ISO 14001｜OHSAS 18001

DCR-511 Mini receiver

Parts and functions

1. Antenna

2. Press to talk

3. Volume control

4. Power/frequency synchronizing

5. Power indicator

6. Reception indicator

1

2

7. Earphone jack (Ø 3.5mm)

3

8. Mini USB charging port

9. Reset

4

9

5 6 7

8

Instructions

1. Power ON/OFF: To turn on the receiver, press the power button for one second and the power indicator will turn green. It turns red when battery is low or during charging. To turn off the receiver, press and hold the power button for about 3 seconds and the indicator light will go off.

2. Press to talk button: Press the talk button to talk with your guide and the conversation could be heard by other members. And release to stop.

3. Reception indicator: The LED stays green within the reception range from the tour guide. Once beyond the reception range, it will flash red and beep as a warning of dropout. In this case, please catch up and go nearer to the tour guide.

4. Charging: During charging, the red light will go off once the battery is full. The charging process takes approximately four hours. Charging can be done by either mini USB or the dedicated charging box.

-2-

Frequency synchronizing between DCT-511 and DCR-511

1. Even though the transmitter and receiver (in the same package) were ready paired at the factory, it is highly recommended that before the tour begins, the receiver should do a fresh synchronization with the specific tour leader’s transmitter.

2. Before synchronization, please make sure that the battery has enough power and then turn off the devices. Frequency synchronizing isn’t workable if the power is weak with indicator glowing RED.

3. To begin the synchronization, press DCT-511’s power button for five seconds till the mute indicator flashes green, which implies readiness to synchronize.

4. Press DCR-511’s power button for five seconds till the reception indicator flashes green, which implies readiness to synchronize. Both mute and reception indicators will glow green after the setting is completed.

5. DCT-511’s mute indicator will stop flashing after a setting period of about twelve seconds.

6. DCR-511’s reception indicator will stop flashing after a setting period of about twelve seconds.

7. To synchronize mass receivers with the transmitter, just follow STEP 2 on all receivers simultaneously.

8. Once the transmitter and receiver are synchronized, they will stay synchronized and no synchronization is needed for next subsequent usages.

-3-

ISO 9001｜ISO 14001｜OHSAS 18001

LED status of DCT-511

Part

Antenna

MUTE button

Volume Control

Power / Synchronization

MODE switch

AUX IN

Power LED

MUTE Indicator LED

Earphone IN

Mini USB socket

Reset

LED status of DCR-511

Parts

Antenna

Press to Talk button

Volume Control button

Power / Synchronization

Power Indicator

Reception Indicator

Earphone Jack

Mini USB socket

Reset

LED Function

1 Signal transmission

2 Muting ON / OFF

3 +- Loudness

4 Power ON / Off or Synchronization

5 MIC – MIX – AUX IN position switch

6 AUX IN (3.5mm)

7 Power ON / OFF indicator

8 MUTE ON / OFF or Synchronization indicator

9 Earphone IN socket (3.5mm)

10 Charging port

11 Reset

LED Function

1 Signal Receiving antenna

2 Press to Talk

3 +- Loudness

4 Power ON / Off or Synchronization

5 Power Indicator LED

6 Reception Indicator

7 Earphone input jack (3.5mm)

8 Charging port

9 Reset

-4-

POWER Indicator (Transmitter, Receiver)

Both indicators are next to the individual antenna.

Action Power LED

1. Press Power button of transmitter for GREEN

1 second. RED

2. Press power buttonof receiver for 1 second

1. When power is ON, Press Power button of transmitter for about 3 second.

2. When power is ON, Press power button of receiver for about 3 second

GREEN light goes off

During charging RED goes off

Indication

Power ON

Battery is low or charging is in progress

Power is OFF

Battery is fully charged

Before synchronization

Transmitter DCT-511

Action

Press transmitter POWER button for 1 second

Power LED

(next to antenna)

1. RED

2. GREEN

Indication

1. Battery weak, not ok for synchronization

2. Battery good, ok for synchronization

Receiver DCR-511

Action

Press transmitter POWER button for 1 second

Power LED

(next to antenna)

1. RED

2. GREEN

Indication

1. Battery weak, not ok for synchronization

2. Battery good, ok for synchronization

-5-

ISO 9001｜ISO 14001｜OHSAS 18001

During Synchronization

Synchronization indicator LEDs to watch:

Transmitter MUTE indicator LED (next to Earphone IN)

Receiver Reception indicator LED (next to Earphone IN)

Action LED

Press transmitter DCT-511 power button for 5 seconds

Indication

MUTE indicator flashes

GREEN

Transmitter is ready for synchronization

Press receiver DCR-511 power button for 5 seconds

After performing the above actions

RECEPTION LED flashes

GREEN

Receiver is ready for synchronization

Both MUTE LED and

RECEPTION LED glowing permanent

GREEN

Synchronization setting is

DONE and system is ready for use.

-6-

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:





Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.





Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of

20 centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CHIAYO ELECTRONICS CO.,LTD.

Http://www.chiayo.com.tw Email: [email protected]

Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan｜Tel:886-2-27415741｜Fax: 886-2-27525242

Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan｜Tel:886-5-2711000｜Fax:886-5-5767611

12I1313

-7-