Earthquake 9060300, 9060140, 9080300, 9080140, 9010400 Chipper/Shredder, 1692327 Vacuum Kit, 1692210 Tow Bar Kit Operating Instructions & Parts Explosions

OPERATING INSTRUCTIONS &
Parts EXPLOSIONS
CHIPPER/SHREDDERs
Model No.
9060300
9060140
9080300
9080140
9010400
1692327
1692210
Description
8.50 Torque Rated Briggs Earthquake Chipper / Shredder
8.25 Torque Rated Briggs Earthquake Chipper / Shredder (CE)
13.50 Torque Rated Briggs Earthquake Chipper / Shredder
13.50 Torque Rated Briggs Earthquake Chipper / Shredder (CE)
14.50 Torque Rated Briggs Earthquake Chipper / Shredder
Vacuum Kit
Tow Bar Kit
ARDISAM
.com
Manual No. 1713250
Rev. Date 2/15/07
© Copyright 2007 Ardisam, Inc.
All Rights Reserved. Printed in USA.
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Table of Contents
Safety Rules & Information................................. 2
Safety Decals...........................................................6
Safety Icons.............................................................7
Identification Numbers.............................................8
Initial Assembly................................................... 9
Initial Assembly........................................................9
Features & Controls.......................................... 12
Control Functions...................................................12
Operation............................................................ 13
General Operating Safety......................................13
Adding Fuel............................................................13
Starting the Engine................................................13
Stopping the Engine...............................................14
Processing Materials..............................................14
Chipping / Shredding Recommendations..............15
Storage..................................................................15
Regular Maintenance........................................ 16
Maintenance Schedule & Procedures....................16
Check for Loose Hardware....................................16
Check Safety Labels..............................................16
Inspect Cone, Hopper, & Guards...........................16
Clean Debris from Engine & Chipper.....................17
Inspect / Rotate Shredding Hammers....................17
Inspect Chipping Knives.........................................18
Check / Change Engine Air Cleaner......................18
Replace Spark Plug...............................................18
Engine Oil Type and Capacity................................19
Check Engine Oil Level..........................................19
Change Engine Oil.................................................19
Troubleshooting & Repair................................. 20
Troubleshooting Chart............................................20
Repair....................................................................21
Specifications.................................................... 23
Parts & Accessories.......................................... 23
Parts Explosions & Listings....................................24
Certificates of Conformity.......................................30
NOTE: In this manual, “left” and “right” are referred
to as seen from the operating position.
Warranty
ONE Year Limited Warranty
The Ardisam, Inc., Manufacturing Company warrants this chipper/shredder to be free from defects in material or workmanship.
Conditions of this warranty include:
What is covered under warranty:
For the first year from the date of purchase, Ardisam will furnish 100% parts and labor to correct any defect caused by faulty
material or workmanship. All products returned to Ardisam, Inc. for warranty repair must have prior approval by calling
our customer service department at 800-345-6007 for a return material authorization number (RMA#). Items subject to
normal wear and tear, due to the nature of their function are not covered under this warranty. Any unit used in a commercial
application is covered for a period of 90 days after purchase. The engine is covered under a separate warranty issued by the
engine manufacturer as stated in the engine manual.
What is not covered under warranty:
This warranty applies only to products which have not been repaired or altered outside our factory. It covers only
defects resulting from normal use, and does not cover defects arising from misuse, alteration, negligence, or accident.
This warranty applies only to the original purchaser and is nontransferable.
This warranty supersedes all other warranties either expressed or implied and all other obligations or liabilities on our part.
Ardisam, Inc., does not assume, and does not authorize any other person to assume for us, any liability in connection with
the sale of our products. This guarantee is void unless the warranty card is properly filled out and returned to Ardisam,
Inc., Cumberland, Wisconsin, within two weeks of the purchase date.
Earthquake, A Division of Ardisam, Inc.
1690 Elm Street; P.O. Box 666
Cumberland, Wisconsin 54829
800-345-6007 · Fax (715) 822-2223
E-mail: [email protected]
800-345-6007
Page OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Safety Rules & Information
Operating Safety
Congratulations on purchasing a superior-quality piece
of lawn and garden equipment. Our products are
designed and manufactured to meet or exceed all industry
standards for safety.
Power equipment is only as safe as the operator. If it is
misused, or not properly maintained, it can be dangerous!
Remember, you are responsible for your safety and that of
those around you.
Use common sense, and think through what you are
doing. If you are not sure that the task you are about to
perform can be safely done with the equipment you have
chosen, ask a professional: contact your local authorized
dealer.
Read the Manual
The operator’s manual contains important safety information you need to be
aware of BEFORE you operate your unit as well as DURING operation.
Safe operating techniques, an explanation of the product’s features and
controls, and maintenance information is included to help you get the
most out of your equipment investment.
Be sure to completely read the Safety Rules and Information found
on the following pages. Also completely read the Operation section.
Children
Tragic accidents can occur with children. Do not allow
them anywhere near the area of operation. Children
are often attracted to the unit and usage activity. Never
assume that children will remain where you last saw
them. If there is a risk that children may enter the area
where you are operating, have another responsible adult
watch them.
Page 800-345-6007
Safety Rules and Information
Moving Parts
This equipment has many moving parts that can injure you or
someone else. However, if you follow all the rules in this book,
the unit is safe to operate.
The chipper/shredder has spinning blades that can amputate
hands and feet. Do not allow anyone near the equipment
while it is running! Do not place hands or feet in the hopper or
chipper cone, or discharge chute.
Thrown Objects
This unit discharges debris at high speeds. Always wear protective goggles
and do not operate without the debris bag in place. Also, do not allow anyone
in the area while the unit is running! If someone does enter the area, shut the
unit off immediately until they leave. Organize the work area prior to starting
work.
Fuel and Maintenance
Gasoline is extremely flammable. Its vapors are also extremely flammable
and can travel to distant ignition sources. Gasoline must only be used as a
fuel, not as a solvent or cleaner. It should never be stored any place where
its vapors can build up or travel to an ignition source like a pilot light. Fuel
belongs in an approved, plastic, sealed gas can, or in the fuel tank with the
cap securely closed. Spilled fuel needs to be cleaned up immediately.
Proper maintenance is critical to the safety and performance of your unit.
Be sure to perform the maintenance procedures listed in this manual,
especially periodically testing the safety system.
800-345-6007
Page Safety Rules & Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
This unit is capable of amputating hands and feet and throwing objects. The triangle
in text
signifies important cautions or warnings which must be followed.
Preparation
1. Do not operate the equipment without wearing
adequate outer garments and safety goggles. Avoid
loose-fitting clothes and use protective footwear that
will improve footing on slippery surfaces.
Training
1. Read the operating and service instructions carefully.
Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the control quickly.
2. Keep the area of operation clear of all persons,
particularly small children, and pets.
General operation
1. Read, understand, and follow all instructions in the
manual and on the unit before starting.
2. Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
3. Only allow responsible adults, who are familiar with
the instructions, to operate the unit (local regulations
can restrict operator age).
4. Be sure the area is clear of other people before
operating. Stop the unit if anyone enters the area.
5. Never direct discharge material toward anyone. Avoid
discharging material against a wall or obstruction.
Material may ricochet back toward the operator.
6. Operate the machine only in daylight or good artificial
light.
7. Do not operate the unit while under the influence of
alcohol or drugs.
8. Always wear eye and hearing protection when
operating this unit.
9. Keep in mind the operator is responsible for accidents
occurring to other people or property.
10.It is a violation of California Public Resource Code
Section 4442 to use or operate the engine on or near
any forest-covered, brush-covered, or grass-covered
land unless the exhaust system is equipped with a
spark arrester meeting any applicable local or state
laws. Other states or federal areas may have similar
laws.
11.Always operate the chipper/shredder outdoors, on a
firm, level, earthen or grassy surface where the unit
will be stable and stay in position. Never attempt to
operate the unit on a slope, or on a wet or slippery
surface where you could slip and fall toward the
chipper cone or hopper openings.
12.Never operate the chipper/shredder on asphalt,
concrete, or other hard surfaces as material being
ejected out of the discharge chute could ricochet,
causing injury to you or bystanders.
13.Always obey the size limitations for tree limbs and
branches stated in the Waste Materials Guide portion
of this manual.
Page 14.Never leave the machine running unattended. Always
turn off the engine, wait for the rotor to come to a
complete stop, and disconnect the spark plug before
leaving the area. Always move the unit to a safe
storage area when not in use.
15.Always maintain secure footing and solid balance
while starting or operating the chipper/shredder.
Never lean directly over the machine.
16.Always stand to the side of the chipper cone when
feeding tree limbs and branches into the unit, as tree
limbs, branches, and harder woods may kick back
while being chipped.
17.Always keep hands out of the chipper cone and
shredder hopper when feeding materials. Never wrap
fingers tightly around branches as you are feeding
them into the unit, as a sudden inward surge could
pull your hands and arms into the unit.
18.Never allow material to build up in the discharge
area or shredding chamber, as this may cause new
material being fed into the machine to kickback with
sufficient force to injure you or other bystanders.
19.Never allow material to build up around the engine
during chipper/shredder operation. This could result in
a fire, or overheating of the engine.
20.Never attempt to reposition or move the chipper/
shredder unit while it is running. Doing so could cause
the machine to tip over, and reaching to steady the
unit could result in accidental insertion of your hands
into the chipper cone or shredder hopper areas.
21.Never continue to operate the machine if it starts
making unusual noise or vibration. Shut the engine
off immediately, allow the rotor to stop, disconnect the
spark plug wire and secure the wire away from the
spark plug. Inspect the unit for any signs of damage
or foreign material in the chipping or shredding areas.
Remove any solid material that may be preventing the
unit from operating properly.
22.Never attempt to clear clogs from the chipper cone,
shredder hopper or discharge chute while the unit is
running. Always shut the engine off, allow the rotor
to come to a complete stop, and remove the spark
plug wire from the spark plug before removing excess
materials.
23.Never attempt to perform any maintenance, repairs,
or attachment of accessories while the unit is running.
Always shut the unit off, allow the rotor to come to a
complete stop, and remove the spark plug wire from
the spark plug before beginning these activities.
24.Always make sure that the shredding chamber,
shredder hopper, and chipper cone are empty before
starting the unit after it has been idle. Attempting to
start the unit with material in these areas could cause
the engine starting cord to stop suddenly, injuring
your hand and fingers, or toppling the unit over.
Vibration is generally a warning sign of trouble.
800-345-6007
Safety Rules and Information
25.Before cleaning, repairing, or inspecting, shut off the
engine and make certain that all moving parts have
come to a complete stop. Disconnect the spark plug
wire and secure the wire away from the spark plug to
prevent accidental starting.
26.Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
27.Never operate the machine without proper guards,
plates, or other safety protective devices in place.28.
Use only attachments and accessories approved of
by the manufacturer or the machine.
transporting and storage
4. Never fuel the machine indoors.
5. Never store the machine or fuel container where
there is an open flame, spark, or pilot light such as
near a water heater or other appliance.
6. Never fill containers inside a vehicle or on a truck bed
with a plastic bed liner. Always place containers on
the ground away from your vehicle before filling.
7. Remove gas-powered equipment from the truck
or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with
a portable container, rather than from a gasoline
dispenser nozzle.
1. Always observe safe refueling and fuel handling
practices when refueling the unit after transportation
or storage.
2. Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an
ignition source (such as a furnace, water heater, etc.)
and cause an explosion. Fuel vapor is also toxic to
humans and animals.
3. Always use the hopper handle and built-in wheels to
move the chipper/shredder. Never lift the unit using
the fuel tank for support. If the unit must be lifted ,
always use at least two people, and always grip the
unit securely using the front leg and hopper handle.
4. Always follow the engine manual instructions for
storage preparations before storing the unit for both
short and long term periods.
5. Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
6. Never store the unit or fuel container inside where
there is an open flame or pilot light, such as in a
water heater. Allow unit to cool before storing.
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the operating activity. Never assume that children
will remain where you last saw them.
1. Keep children out of the work area and under the
watchful care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Never allow children to operate the unit.
Emissions
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. Look for the relevant Emissions Durability Period and
Air Index information on the engine emissions label.
Ignition System
1. This spark ignition system complies with Canadian
ICES-002.
Service and Maintenance
Safe Handling of Gasoline
1. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
2. Use only approved gasoline containers.
3. Never remove the gas cap or add fuel with the engine
running. Allow the engine to cool before refueling.
800-345-6007
Page Safety Rules and Information
Safety Decals
All DANGER, WARNING, CAUTION and instructional
messages on your unit should be carefully read and
obeyed. Personal bodily injury can result when these
instructions are not followed. The information is for your
safety and it is important! The safety decals below are on
your unit.
This unit has been designed and manufactured to
provide you with the safety and reliability you would
expect from an industry leader in outdoor power
equipment manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and
effectively, we have placed several safety labels on the
unit to remind you of this important information while you
are operating your unit.
Decal - Operating Instructions,
North American Models
DANGER
To avoid serious
personal injury from
rotating cutting
blades, keep hands
out of inlet while
machine is running.
Decal - Operating Instructions,
CE Models
WARNING
Avoid Serious Injury or Death
• Read and follow the operating instructions.
• Know the location and function of all controls.
• Wear proper safety goggles and hearing
protection.
• Never wear loose clothing.
• Keep hands and clothing clear of material
being pulled into the unit.
• Keep hands and feet away from the discharge
chute area.
• Keep safety devices (guards & shields)
in place and working.
• Do not operate when children or others
are present.
• Be sure all moving parts have stopped
before placing hands near the cutting
blades.
• When leaving the machine, shut off the
engine.
NO HANDS BELOW THIS LINE
Decal - Danger,
Rotating Cutting Blades,
North American Models
1731918
1731919
Decal - Danger,
Rotating Cutting Blades, Warning, Debris,
North American Models
DANGER
DANGER
Amputation Hazard
To avoid serious personal injury from rotating
cutting blades, keep hands out of inlet while
machine is running.
1732039
1731920
Decal - Danger,
Rotating Cutting Blades,
CE Models
Page These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
Amputation
Hazard
WARNING
Thrown Objects
Hazard
To avoid serious personal injury from
To avoid serious personal injury from
rotating cutting blades, keep hands out discharged debris, never operate
of discharge while machine is running. without the discharge bag installed.
1732181
Amputation Hazard
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
1731921
Decal - Danger,
Thrown Objects, Do Not Operate
Without Collection Bag,
CE Models
800-345-6007
Safety Rules and Information
Safety Icons
Warning: Read Operator’s
Manual.
Read and understand the
Operator’s Manual before using this
machine.
Danger: Thrown Objects.
This machine is capable of throwing
objects and debris. Keep bystanders
away.
Danger: Amputation Hazard.
Danger: Thrown Objects.
To avoid serious personal injury from
rotating cutting blades, keep hands
out of inlet while machine is running.
This machine is capable of throwing
objects and debris. Keep bystanders
and children away when engine is
running.
1731919
1731919
Danger: Wear Appropriate Safety
Equipment.
Danger: Do Not Place Hands in
the Machine.
This machine is capable of throwing
objects and debris. Always wear
safety goggles while operating.
To avoid serious personal injury from
rotating cutting blades, keep hands
out of inlet while machine is running.
Do not place hands in areas where
this symbol is present.
This machine’s operating sound
power level is 109 dB(A) or more.
Wear hearing protection while
operating.
1731919
1731919
Warning: Disconnect the Spark
Plug Wire Before Servicing.
Disconnect the spark plug wire, and
secure it away from the spark plug
before servicing the unit.
1731919
1731919
800-345-6007
Page Safety Rules and Information
Identification Numbers
When contacting your authorized dealer for
replacement parts, service, or information you
MUST have these numbers.
Record your model name/number, manufacturer’s
identification numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.
ID Tag
CE Models: Place the extra copy of the identification tag
in the manual.
PRODUCT
Reference
Data
Model Description Name/Number
Unit PART Number
Unit SERIAL Number
Dealer Name
Date Purchased
ENGINE Reference Data
Engine Make
Engine Model
Engine Type/Spec
Engine Code/Serial Number
CE Identification Tag Markings
A. Manufacturer’s Identification Number
B. Power Rating in Kilowatts
C. Maximum Engine Speed in Rotations per Minute
D. Sound Pressure at Operator’s Position in Decibels *
E. Manufacturer’s Address
F. Year of Manufacture
G. CE Compliance Logo
H. Mass of Unit in Kilograms
I. Sound Power in Decibels **
This unit complies with European Harmonized Lawn Mower
Standard EN 836, European Machinery Directive 98/37/EC,
and European EMC Directive 89/336/EC
A
B
F
G
I
C
D
H
E
CE Specifications
Model Number: 9060140 / 9080140
* Tested according to EN836:1997/A2:2001
Engine Maximum RPMs: 3700
** Tested according to 2000/14/EC
Power Rating: 4 kW
Mass: 52kg
Noise Guaranteed Sound Power (LwA): 109 dB(A)
Noise Sound Pressure Level (LpA): 96 dB(A)
Page 800-345-6007
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Initial Assembly
D
A
C
B
Figure 18. Installing the Chipper Cone
A.1/4-20 x 3/4 Screw, Washer, & Nut
B. 5/16-18 Flange Nut
C. Cone Base
D. Chipper Cone
Figure 19. Attaching the Hopper
Initial Assembly
Install Chipper Cone - All Models
1. Secure the chipper cone (D, Figure 18) to the chipper
cone base (C) using 1/4-20 x 3/4 screws, washers,
and nuts (A).
2. Position the chipper cone base (C) over the three
5/16-18 threaded studs protruding from the engine
plate, and attach using three 5/16-18 flange nuts (B).
3. Rotate cone and cone base away from engine so
cone does not contact engine.
4. Tighten the flange nuts securely.
Figure 20. Installing Hardware Inside the Hopper
Install the Hopper - All Models
1. Remove two 1/4 locknuts and flat washers from
hopper liner and set aside. Attach the hopper to the
rotor housing. Make sure to engage the metal lip of
the hopper liner inside the housing.
2. Secure the hopper to the rotor housing using two
5/16 x 1/2 hex head bolts, two 5/16 flat washers and
hardware removed from step 1 (Figure 19). Do not
tighten hardware at this time.
3. See Figure 20. From the inside of the hopper install
one 5/16-18 x 3/4 hex head bolt, 5/16 lockwasher,
and 5/16 flat washer into each of the upper and lower
holes of the metal hopper liner. Finger tighten only at
this time.
800-345-6007
Page Initial Assembly
4. Check that the hopper is seated correctly and tighten
all hardware.
Install the Handle - All Models
1. Lift the hopper handle up until the outer holes in the
handle align with the holes in the shredder hopper
and secure with 1/4-20 x 3/4 screws, washers, and
nuts (A, Figure 21). Insert the screws from the
outside of the shredder hopper.
A
Figure 21. Installing the Hopper Handle
A.1/4-20 x 3/4 Screw & Nut
Page 10
800-345-6007
Initial Assembly
Lift discharge
chute and slide
bag over chute.
Make sure bag
noose fits over
top of discharge
chute and notch
in chute bottom.
Pull drawstring tight.
Figure 22. Discharge Bag - North American Models
Slide bag over discharge chute.
Make sure bag
noose fits over top
of discharge chute
and notch in chute
bottom.
Pull drawstring tight.
Figure 23. Discharge Bag - CE Models
Install Discharge Bag
This product comes with a discharge bag for collection of
debris as it exits the discharge chute. Install the bag as
shown in Figure 22 or 23.
Add Engine Oil
Refer to “Engine Oil Type and Capacity” in the Regular
Maintenance section for oil type and fill procedures.
Add Fuel
Refer to “Adding Fuel” in the Operation section for fuel
specifications and filling procedures.
800-345-6007
Page 11
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Features and Controls
Figure 1. Controls
Control Functions
The information below briefly describes the function of individual controls. Operating requires the combined use of
several controls applied in specific sequences. To learn what combination and sequence of controls to use for various
tasks see the OPERATION section.
the engine starts. A warm engine may not require
choking. Move the lever right to close the choke.
Engine Stop / Throttle Control
The engine stop / throttle control lever controls turn
the engine off and controls the engine speed. Move
the throttle right to increase engine speed and left to
decrease engine speed. Moving the lever all the way
to the left stops the engine. Always operate at FULL
throttle (lever fully right).
Fuel Tank
To remove the cap, turn counterclockwise.
Chipper Cone / Shredder Hopper
Chipper Cone: The chipper cone is located on the front
of the unit next to the engine. Insert branches and tree
limbs up to approximately 3” (7.6 cm) in diameter into the
chipper cone. NEVER insert hands past the mouth of
the cone.
Recoil Starter
The recoil starter is used to turn the engine over for
starting.
Shredder Hopper: The shredder hopper is on top of the
unit. Leaves and other light waste can be loaded into the
shredder hopper. NEVER insert hands into the hopper .
Fuel Shut-Off Valve
The fuel shut-off valve is located below the air cleaner
housing. Always close the valve when the unit is not in
use.
Debris Bag: Use the debris bag to collect the material
discharged from the unit. Do not operate the unit without
the debris bag in place.
Choke
Close the choke for cold starting. Open the choke once
Page 12
800-345-6007
12
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Operation
General Operating Safety
Be sure to read all information in the Safety and
Operation sections before attempting to operate this unit.
Become familiar with all of the controls and how to stop
the unit.
Upon start-up and shut-down, you may hear the
metal-to-metal sound of the triangular hammers and Jhammers positioning themselves on the rotor. This is
normal. If this sound continues after the machine has
reached full speed, contact your dealer for an inspection
of the unit. Overloading the equipment will shorten its
life, and can cause mechanical failures.
Chipper Operation
The chipper is designed to handle tree limbs and
branches up to approximately 3” (7,6 cm) in diameter.
The chipping knives also permit the processing of course
organic matter like corn stalks. Tree branches must be
inserted large-end first into the chipper cone. Since
occasional kick-backs may occur, always stand off to the
side of the unit. Allow the self-feeding action of the unit
to draw the sticks in.
Shredder Operation
The shredder is designed to shred light brush, leaves,
and other soft but bulky organic waste. As material is
loaded into the shredder hopper it is pulled into the path
of the triangular and J-hammers by air flow.
Vacuum Attachment (Optional)
WARNING
To avoid serious personal injury from rotating
cutting blades, keep hands out of inlet while
machine is running.
In addition to the chipper cone and hopper, loose debris
may be processed by the Vacuum hose adapter kit.
Leaves may be raked directly into the leaf tray where
vacuum action will draw them into the shredder. For
hard-to-reach areas, the nozzle and hose assembly may
be used. The strength of the Vacuum may be changed
using the rotating sleeve on the nozzle. (See Vacuum Kit
parts explosion on page 28.)
Operating Location
Select an area with firm, level ground, covered by dirt or
grass. Do not operate on wet or slick surfaces, or near
bystanders. Locate and organize the materials to be
processed so that you don’t have to walk in front of the
inlet or discharge openings, and so you have adequate
room to work safely.
800-345-6007
DANGER
The exhaust from this product contains carbon
monoxide gas. Carbon monoxide is a colorless,
orderless, and tasteless gas that can cause
dizziness, nausea, unconsciousness, or even
brain damage and death if inhaled for prolonged
periods.
Operate the unit outdoors in a well ventilated
location only. Keep children, pets, and bystanders
away.
Failure to follow these instructions may result in
serious injury or death.
Adding Fuel
Do not use gasoline containing METHANOL,
gasohol containing more than 10%
ETHANOL, gasoline additives, or white gas
because engine/fuel system damage could
result.
WARNING
Gasoline is highly flammable and must be handled
with care. Never fill the tank when the engine is
still hot from recent operation. Do not allow open
flame, smoking or matches in the area. Avoid
over-filling and wipe up any spills.
To add fuel:
1. Remove the fuel cap (see Figure 1).
2. Fill the tank. Do not overfill. Leave room in the tank
for fuel expansion. Refer to your engine manual for
specific fuel recommendations.
3. Install and hand tighten the fuel cap.
Starting the Engine
1. Set the throttle to FULL.
2. Close the choke.
NOTE: A warm engine may not require choking.
3. Place one foot on the front support leg to hold the
unit firmly in place.
4. Pull the starting rope out to begin turning the engine
over. Pull slowly at first and increase speed with
each successive pull.
5. After the engine starts, open the choke and move the
engine throttle control to SLOW. Warm up the engine
Page 13
Operation
by running it for at least a minute.
6. Set throttle to FULL and begin chipping/shredding.
Stopping the Engine
NOTE: In the event of an emergency the engine can be
stopped by setting the throttle control to STOP.
1. Slide the throttle control fully left to the
STOP position.
NOTE: Upon start-up and shut-down, you may hear the
metal-to-metal sound of the triangular hammers and Jhammers positioning themselves on the rotor. This is
normal.
2. After the engine has stopped moving, remove the
spark plug wire and remove any debris from the unit
and engine.
Processing Materials
Most materials to be processed can be handled more
efficiently by following these tips.
Chipping Tips:
Figure 2. Chipping.
• Prune branches down close to the main branch to
make feeding them into the chipper cone easier.
• Large, hard, dried tree branches that resist chipping
can be processed by rotating them as you alternately
insert and retract them.
• If the material to be chipped is extremely hard, kicks
back forcefully when being fed into the chipper cone,
or cannot be easily controlled, remove the material
immediately and set it aside.
• If additional force is required to insert materials
into the chipper, the blades probably need to be
sharpened. Consult the Troubleshooting and Repair
section of this manual, or see your authorized dealer.
• Maintain control of the materials you are feeding to
prevent them from whipping around.
• Do not insert short pieces of material into the chipper
cone by hand. Use a larger piece of material to force
them into the chipper cone.
Shedding Tips
• Don’t overload the shredder by dumping large
volumes of material into the hopper opening.
• Alternate loads of wet and dry material to prevent the
discharge from becoming plugged.
• Never use any object to force material into the
shredding chamber. It could get caught in the
shredding hammers and damage the unit.
Page 14
Figure 3. Shredding.
800-345-6007
Operation
Chipping & Shredding Recommendations
Operation
Type of Waste
Permitted
Size Limitations
Notes
Shredding
Dry or moist organic
material including leaves,
plants, flowers, fruits, or
vegetables.
Branches and twigs up to
1/2” diameter and 18” long.
Alternately chip or shred moist green
waste with dry waste to avoid plugging
of the discharge chute.
Long, thicker tree limbs or
small bunches of smaller
sticks grouped together for
ease of handling.
Tree limbs and branches,
or bundles of small sticks
grouped for easier handling.
Maximum diameter of
approximately 3” (7,6 cm).
Chipping
Process at a feeding rate that allows the
rotor to keep up and maintain a high rate
of speed.
Bulky tree limbs should be pruned close
to the main stem. Always use a shorter
piece of wood to push end pieces into
the chipper cone. Never place hands in
the chipper cone.
Never chip very hard or dry materials
such as kiln dried dimensional lumber
(2x4’s etc.) or other building materials.
Never use the chipper to process
pressure-treated wood products.
Vacuum
Attachment
Light, loose, dry waste such Small materials that will not The vacuum is engineered for small,
as leaves, grass clippings, obstruct the vacuum hose. loose waste and for cleaning around
or sawdust.
decorative landscaping and flower
beds. Twigs, wet leaves, and other bulky
materials will clog the hose or obstruct
the shredding chamber.
Storage
Before you store your unit for the off-season, read the
Maintenance and Storage instructions in the Safety
Rules section, then perform the following steps:
• Perform engine maintenance and storage measures
listed in the engine owner’s manual. This includes
draining the fuel system, or adding stabilizer to
the fuel (do not store a fueled unit in an enclosed
structure - see warning).
Before starting the unit after it has been stored:
• Check all fluid levels. Check all maintenance items.
• Perform all recommended checks and procedures
found in the engine owner’s manual.
• Allow the engine to warm up for several minutes
before use.
800-345-6007
Page 15
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Regular Maintenance
Maintenance Schedule & Procedures
The following schedule should be followed for normal care of your unit.
SAFETY ITEMS
Before Every 5 Every 25 Every
100
Each Hours Hours
Use
Hours
Check for loose hardware
Every
250
Hours
•
Spring &
Fall
•
Check all safety labels
•
Inspect cone, hopper, and guards.
•
CHIPPER MAINTENANCE ITEMS
Clean debris from engine and chipper. **
Before Every 5 Every 25 Every
Each Hours Hours
100
Use
Hours
•
ENGINE MAINTENANCE ITEMS
Check Engine Oil Level *
Spring &
Fall
•
Inspect/Rotate Shredding Hammers
Inspect/Rotate Chipping Knives
Every
250
Hours
•
•
Before Every 8 Every 25 Every 50 Every
Each Hours Hours
Hours
100
Use
Hours
•
•
•
Change Engine Oil * **
Check / Change Engine Air Filter * **
Replace Spark Plug *
Spring &
Fall
•
•
*Refer to engine owner’s manual. Change original engine oil after initial break-in period of 5-8 hours.
**More often in hot (over 85° F: 30° C) weather or dusty operating conditions.
Check for Loose Hardware
Inspect Cone, Hopper, & Guards
Service Interval: Every 5 hours; every spring and fall.
Inspect the unit, checking for loose hardware or
components. Pay special attention to the hardware
attaching the chipper cone, hopper, axle, and front leg.
Service Interval: Every spring and fall.
Check that the chipper cone, shredder hopper, and
discharge guards are in place, undamaged, and secure.
Replace any damaged or missing parts.
Check Safety Labels
Service Interval: Every spring and fall.
Check that the safety labels are in place and
undamaged. Sample illustrations and part numbers
of the decals can be found on page 6. Replace any
damaged or missing decals.
Page 16
800-345-6007
Regular Maintenance
A
Figure 4. Clean Debris from Engine Cooling Fins
Figure 5. Inspect Shredder Hammers
A. Access Panel
Clean Debris from Engine &
Chipper
Service Interval: Before each use and every 100
hours.
The engine requires air flow to cool itself and for
combustion. Before each use, clean any debris from the
unit especially from around the air shroud intake, air filter,
and muffler. Every 100 hours, remove the engine air
shroud and clean out any debris from the engine cooling
fins at the locations shown in Figure 4. We recommend
having this service performed by an authorized dealer.
Inspect / Rotate Shredding
Hammers
Figure 6. Triangular Hammer Wear Area
Service Interval: Every 25 Hours, or As Necessary
The shredding hammers of this unit can be rotated to
provide a new cutting surface as required. The triangular
hammers can be rotated twice, then flipped over for a
total of 6 sharp cutting surfaces. The J-hammers can be
flipped over once. To inspect the shredding hammers:
WARNING
Amputation hazard. To avoid serious injury from
accidental starting, always disconnect the spark
plug wire and secure it away from the spark plug
when servicing the unit.
1. Disconnect the spark plug wire and secure it away
from the spark plug.
Figure 7. J-Hammer Wear Area
2. Remove the small circular access panel (A, Figure 5)
from the back of the shredder housing.
3. Inspect the cutting edges of the triangular hammers
(Figure 6) and J-hammers (Figure 7).
800-345-6007
To rotate or replace the shredding hammers, see the
Troubleshooting and Repair section.
Page 17
Regular Maintenance
Inspect Chipping Knives
Service Interval: Every 25 Hours, or As Necessary
The chipping knives of this unit can be rotated or
sharpened to provide a new cutting surface as required.
When inspecting the knives be careful to avoid touching
the sharpened edges. To inspect the chipping knives:
1. Disconnect the spark plug wire and secure it away
from the spark plug.
WARNING
To avoid serious injury from accidental starting,
always disconnect the spark plug wire and secure
it away from the spark plug when servicing the unit.
A
Figure 8. Inspect Chipper Knives
A. Chipper Cone
2. See Figure 8. Remove the nuts securing the chipper
cone to the front of the chipper. Remove the chipper
cone (A) to access the knives.
3. Using the recoil starter, slowly pull the starter rope
to rotate the rotor into position so the blades can be
seen.
To sharpen or replace the chipper knives, see the
Troubleshooting and Repair section.
Check / Change Engine Air
Cleaner
C
D
E
B
Service Interval: Every 25 Hours
The engine air cleaner assembly should be opened,
inspected, and the filer element replaced every 25 hours,
or as required if debris has built up in the assembly.
To replace the air filter and pre-cleaner assembly:
1. Loosen the screw (A, Figure 9) and remove the filter
cover (B).
2. Inspect the pre-cleaner (C) and air filter element (D).
If either are soiled, then replace.
3. Insert the new pre-cleaner (C) and air filter element
(D) inside the filter cover (B). Make sure the arrows
on the filter element are pointed up, and the lip of the
pre-cleaner covers the bottom filter pleats.
4. Insert the cover tabs (F) into the filter base slots.
5. Tilt the cover up into place and tighten the screw (A).
A
F
Figure 9. Change Air Filter
A. Screw
B. Filter Cover
C. Pre-Cleaner
D. Air Filter Element
E. Air Filter Base
F. Slots and Tabs
Replace Spark Plug
Please contact your authorized dealer to perform this
service.
Page 18
800-345-6007
Regular Maintenance
Engine Oil Type & Capacity
Select a quality engine oil using the chart in Figure
10. 5.5 HP models require 5/8 quart (0.6L) of oil. 8HP
models require 7/8 quart (0.8L) of oil.
Use oil classified API Service Class SF,
SG, SH, SJ or better with SAE Viscosity:
30 Conventional**
Check Engine Oil Level
5W-30
10W-30
Conventional*
Service Interval: Before Each Use
Check the engine oil level at the oil fill and level check
plug (A, Figure 11).
5W-30, 10W-30 Synthetic
1. Stop the engine and wait for all moving parts to stop.
2. Remove the oil fill and level check plug (A, Figure 11)
by twisting it counter-clockwise. The oil should be
filled up to the mouth of the filler opening as shown in
the Figure 11 inset.
Change Engine Oil
Service Interval: Every 50 Hours
1. Stop the engine and wait for all moving parts to stop.
Allow the unit to cool before changing the oil.
2. Remove the oil fill and level check plug (A, Figure 11)
by twisting it counter-clockwise.
˚F
-20
0
-30
-18
20 32 40
60
80
100
0 4
16
27
38
*CAUTION: Air cooled engines run hotter than automotive engines.
The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40º F (4ºC) will result in higher than normal
oil consumption. When using a multi-viscosity oil, check oil level
more frequently.
˚C
-7
**CAUTION: SAE 30 oil, if used below 40º F (4ºC), will result in hard
starting and possible engine bore damage due to inadequate
lubrication.
Figure 10. Oil Recommendations
3. Place an oil drain pan below the engine and remove
the oil drain plug (B, Figure 11). Allow the oil to drain
completely.
4. Reinstall the oil drain plug (B). Tighten the plug to
125 inch pounds (14 Nm)
A
5. Add oil to the oil fill hole (A) until the oil level is even
with the bottom edge of the oil fill hole (Figure 11
inset).
B
Figure 11. Oil Fill and Oil Drain
A. Oil Fill & Level Check Plug
B. Oil Drain Plug
800-345-6007
Page 19
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Troubleshooting & Repair
Troubleshooting Chart
While normal care and regular maintenance will extend
the life of your equipment, prolonged or constant use
may eventually require that service be performed to allow
it to continue operating properly.
The troubleshooting guide below lists the most common
problems, their causes, and remedies.
See the information on the following pages for
instructions on how to perform most of these minor
adjustments and service repairs yourself. If you prefer,
all of these procedures can be performed for you by your
local authorized dealer.
PROBLEM
WARNING
To avoid serious injury, perform maintenance on
the unit only when the engine is stopped.
Always disconnect the spark plug wire and
fasten it away from the plug before beginning the
maintenance, to prevent accidental starting of the
engine.
CAUSE
Engine will not start.
1.
2.
3.
4.
5.
6.
7.
Out of fuel.
Spark plug wire disconnected.
Engine controls not set correctly.
Spark plug fouled.
No compression. Recoil starter pulls with no resistance.
No spark. Ignition problem.
Old or stale fuel.
REMEDY
Add fuel.
Reconnect spark plug wire.
Refer to Starting in the Operation section.
Remove the spark plug, clean or replace.
See your authorized dealer.
See your authorized dealer.
See your authorized dealer.
Engine exhaust is black.
1. Dirty air filter. 2. Choke closed.
Replace air filter. See engine manual.
Open choke.
Engine runs but no material is discharged. 1. Discharge chute clogged. 2. Engine not running at full speed.
Clean out debris.
Set throttle control to FAST.
Excessive branch vibration when 1. Chipper knives dull.
chipping materials.
2. Tree limbs are extremely hard or dried out.
Sharpen or replace chipper knives.
Material is not suitable for chipping.
Unusual noise or vibration when. 1. Rotor overloaded with material.
processing material.
2. Hammers are broken, bent, or loose.
3. Hammers frozen in place.
Allow unit to clear itself before adding more material to the hopper.
Check assembly. Tighten or replace as
required.
Check for obstructions and debris. Repair as necessary.
Vacuum not working.
Install lid.
Allow material to dry.
Attach hose per instructions (see hose kit).
Clear blockage or replace.
Set throttle control to FAST.
Page 20
1.
2.
3.
4.
5.
Hopper lid not in place. Material too wet.
Hose not attached properly.
Hose obstructed or damaged.
Engine not running at full RPM.
800-345-6007
Troubleshooting & Repair
Figure 12. Removing the Shredder Hopper
Figure 13. Removing the Rotor Housing
Repair
F
E
Shredding Hammer Rotation and
Replacement
G
The cutting edges of the shredding hammers may
eventually wear out requiring rotation of the hammer or
replacement if all cutting edges have been dulled.
Triangular hammers can be rotated twice after the first
edge dulls, then flipped over once and rotated again for a
total of 6 edges. J-hammers can be flipped over once for
a total of two cutting edges.
To rotate the shredding hammers:
1. Turn the engine off and wait for all moving parts to
stop.
2. Disconnect the spark plug wire and secure it away
from the spark plug.
D
C
B
WARNING
A
To avoid serious injury from accidental starting,
always disconnect the spark plug wire and secure
it away from the spark plug when servicing the unit.
D
3. Detach the shredder hopper from the rotor housing
(Figure 12).
C
4. Remove the rotor cover by removing the hardware
that secures it to the main housing (Figure 13).
5. Note the assembly sequence of the hardware used to
secure the hammers (Figure 14). Using a 5/16” allen
wrench remove the socket head capscrew (A) and
related hardware.
6. Inspect the hammers (G, H), spacer tubes (D, F),
and hardware. If the spacer tube (D, F) shows signs
of wear, replace it. Inspect and flip, or replace the
hammers (G, H).
7. Reassemble the hammers, spacers, washers, and
800-345-6007
B
F
A
H
E
Figure 14. Removing the Rotor Housing
A. Socket Hd. Capscrew
E. Spacer, Short
B.Lockwasher, 3/8
F. Washer, 3/8 (8HP Only)
C. Washer, 7/8
G.J-Hammer
D. Spacer, LongH. Triangular Hammer
Page 21
Troubleshooting & Repair
capscrews. Torque the socket head capscrews (A)
to 30-35 ft. lbs. (41-47 N.m.)Refer to Figure 14 for
assembly. The J-hammer (G) on the opposite side of
the rotor faces outward for balanced rotation.
Repeat for all the hammers.
Chipping Knives Sharpening and
Replacement
The chipping knives should be sharpened or replaced
when tree limbs require extra force to feed into the
chipper cone.
The chipping knives may be resharpened at a 30 degree
angle until the distance between the edge of the blade
bevel and the mounting hole is less than 1/16” (1.6mm)
(see Figure 17).
Figure 15. Installing the Chipper Cone
WARNING
Amputation hazard. To avoid serious injury from
accidental starting, always disconnect the spark
plug wire and secure it away from the spark plug
when servicing the unit.
A
To inspect, sharpen, or replace the chipping knives:
1. Turn the engine off and wait for all moving parts to
stop.
2. Disconnect the spark plug wire and secure it away
from the spark plug.
3. Detach the shredder hopper from the rotor housing
(see Figure 12).
4. Remove the rotor cover by removing the hardware
that secures it to the main housing (see Figure 13).
Figure 16. Access Hole
A. Access Hole
Top View
Side View
1/16”
Min
WARNING
Cutting hazard. To avoid serious injury, avoid
contacting the sharp cutting edges of the chipping
knives.
5. Remove the chipper cone base (Figure 15).
30°
Figure 17. Chipper Knife Minimum Cutting Edge
6. Rotate the rotor assembly so that the socket head
capscrews that secure one of the chipper knives can
be accessed through the rotor cover and access hole
(Figure 16).
7. Using a 1/4” hex wrench, loosen and remove the two
socket head capscrews and chipper knife.
8. Inspect, rotate, sharpen, or replace the chipper knife.
9. Reinstall the chipper knife and tighten the socket
head capscrews to 18-20 ft. lbs (24-27 N.m.).
10.Rotate the rotor 180 degrees and repeat with the
other chipper knife. Reinstall the rotor cover and
shredder hopper when completed.
Page 22
800-345-6007
OPERATING INSTRUCTIONS and parts explosions
Chipper/Shredder Models
Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained equipment horsepower will likely be lower due to operating
limitations and environmental factors.
CHASSIS:
All Models
Chipping Capacity Approximately 3” (7.6 cm)
Shredding Capacity 1/2” x 18” Long
Chipping Knives 2
Shredding Hammers 2 J-hammers,
2 triangular hammers
Waste Reduction Ratio Approximately 20:1
Weight
Model 9060300 8.50 Torque Rating 130 lbs.
Model 9060140 8.25 Torque Rating 120 lbs.
Model 9080300 13.50 Torque Rating 130 lbs.
Model 9080140 13.50 Torque Rating 145 lbs.
Model 9010400 14.50 Torque Rating 130 lbs.
Parts & Accessories
Replacement Parts
Optional Accessories
Replacement parts are available from your authorized
dealer. Always use genuine Earthquake Service Parts.
Vacuum Kit Model No. 1692327
800-345-6007
Tow Bar Kit Model No. 1692210
Page 23
Parts Explosions & Listings
Hopper & engine group
35
34
Page 24
800-345-6007
Parts Explosions & Listings
Hopper & engine group
KEY #
PART #
DESCRIPTION
QTY.
KEY #
PART #
DESCRIPTION
QTY.
1718055 ENGINE, 5.5 HP BRIGGS
(9060140)
1
1
1960507 BOLT, SOCKET BUTTON HD,
1/4-20 X 3/4
14
23
2
1098100 RETAINER, HOPPER GUARD
1
23
1095100 GUARD, HOPPER
1
600 ENGINE, 6 HP BRIGGS INTEK
HORZ SHAFT (9060300)
1
3
4
1930642 NUT, FLANGE, 2-WAY LOCK,
1/4-20
14
23
800 ENGINE, 8 HP BRIGGS INTEK
(9080300)
1
5
1709603 SUPPORT, HOPPER GUARD
1
23
6
3621100 HANDLE
1
7
1921319 WASHER, PLAIN,
17/64 X 5/8 X 3/64
6
8
1931277 NUT, WHIZ, 5/18-18
20
9
1713272 CASTING, CHIPPER CONE 3"
1
10
1709469 HOPPER, RED
1
11
2005612 SAFETY GOGGLES
1
12
1926106 CAPSCREW, HEX,
5/16-18 X 3-1/4 GR5
1
13A
3685100 DEFLECTOR
1
13B
1709556 DEFLECTOR, FIXED
(EUROPEAN MODELS)
14
1718080 ENGINE, 8 HP BRIGGS
(9080140)
1
23
100 ENGINE, 10 HP BRIGGS
INTEK (9010400)
24
1709403 COLLECTION BAG, 24" X 36"
1
25
LBL200201 DECAL, EARTHQUAKE DASH
1
26
1926025 SCREW, PHILLIPS ROUND
HD, 1/4-20 X 1/2
2
27
1709729 INSERT, CONE
(EUROPEAN MODELS)
1
28
1921960 CAPSCREW, HEX,
1/4-20 X 1 GR5
8
1
29
1960151 WASHER, PLAIN
1/4 X 1-1/4 X 5/64
12
5001612 DECAL, DANGER
1
30
2
15
1960519 NUT, PUSH, 1/2
2
1918249 SCREW, TRUSS HD,
5/16-18 X 3/4
16
1714250 WHEEL & TIRE ASSEMBLY,
12 X 1.75
2
31
1927557 NUT, FLANGE, WHIZ LOCK,
5/16-18
2
17
1924361 WASHER, PLAIN,
17/32 X 1-1/4 X 5/64
2
32
2
18
1928635 SCREW, TAPTITE,
3/8-16 X 1-1/4
4
1709561 HOPPER HALF, UPPER, WIRE
FORM, 5/16 (EUROPEAN
MODELS)
33
1917356 LOCKWASHER, 5/16
10
19
1713099 KICKSTAND ROD
1
34
4
20
1925205 CAPSCREW, HEX,
5/16-18 X 5/8
1
1921515 CAPSCREW, HEX HD,
5/16-24 X 3/4
35
4
21
1709468 CONE, RED
10
1960506 BOLT, SOCKET BUTTON HD,
1/4-20 X 7/8
22
1713281 ENGINE PLATE ASSEMBLY
1
-
1709480 BASE PLATE, ENGINE
1
-
1713200 SPACER, BRIGGS ENGINE
1
-
1713201 PLATE, KICKSTAND, BRIGGS
ENGINE, 8 HP
1
1713203 PLATE, KICKSTAND, BRIGGS
ENGINE, 10 HP
1
695568 MUFFLER GUARD (9060140)
1
800-345-6007
Page 25
Parts Explosions & Listings
Housing & rotor group
Page 26
800-345-6007
Parts Explosions & Listings
housing & rotor group
KEY #
PART #
DESCRIPTION
QTY.
KEY #
PART #
DESCRIPTION
QTY.
1
3525100 LINER, HOPPER
1
21
1916950 NUT, HEX 3/8-16
2
2
1917356 LOCKWASHER, SPLIT 5/16
12
22
1709614 SPACER, TUBE
4
3
6518100 CAPSCREW, SOCKET HD 3/8-16
X 5/8
2
23
1709616 SPACER, 3/4" O.D. X 3/4" LONG
4
23
1713207 SPACER, 1" O.D. X 33/64" LONG
4
4
1930642 NUT, 2-WAY LOCK 1/4-20
2
24
3307612 HAMMER, TRIANGULAR
2
5
1921319 WASHER, FLAT 1/4
2
25
1960507 BOLT, SOCKET BUTTON HD,
1/4-20 X 3/4
2
1921332 CAPSCREW, HEX HD 5/16-18 X
3/4
2
6
26
5004100 DECAL, CAUTION
1
1960508 CAPSCREW, HEX SOCKET HD
W/PATCH 3/8-16 X 2 GR8
4
7
8
6005100 CAPSCREW, SOCKET HD 5/1628 X 1/2
2
27
1924874 WASHER, FLAT 5/16
4
28
3307100 J HAMMER
2
9
1919438 NUT, NYLOCK 5/16-18
2
29
1924940 WASHER, FLAT 7/8" O.D.
4
10
1931277 NUT, HEX FLANGE 5/16-18
12
30
3521100 HOUSING, ROTOR
1
11
3520100 COVER, ROTOR HOUSING
1
31
3501100 HOUSING, FAN
1
12
1920787 CAPSCREW, HEX HD 5/16-18 X
1/2
8
32
3505100 AXLE ASSEMBLY
1
13
3315612 CHIPPER KNIFE
2
33
5001612 DECAL, DANGER
1
35
1676435 WASHER, PLAIN 1/2 X 1-1/4 X
3/16
4
-
1921333 BOLT, HEX HD CAPSCREW,
5/16-18 X 1 GR5
1
14
905100 KEY 1/4 SQ. X 1-7/8
1
15
3299100 SPACER, ROTOR
1
15
1713206 SPACER, ROTOR
1
16
1919326 WASHER, FLAT 5/16
2
-
1714177 ROTOR ASSEMBLY
1
17
1714177 ROTOR, 1" HUB
1
-
1
18
6005612 CAPSCREW, SOCKET HD 5/1624 X 5/8
4
1685698 ROTOR KIT (INCLUDES KEY #'S:
2, 17, 22, 23, 26, 29)
-
1
19
1916965 LOCKWASHER, SPLIT 3/8
7
1660071 ROTOR HAMMERS & KNIVES
ASSEMBLY, 5.5 HP & 6 HP
20
6516100 CAPSCREW, SOCKET HD 3/8-24
X2
1
-
1660092 ROTOR HAMMERS & KNIVES
ASSEMBLY, 8 HP & 10 HP
1
800-345-6007
Page 27
Parts Explosions & Listings
1692210 vacuum kit (optional accessory)
KEY #
QTY.
1A
1021100 ADAPTER
1
1B
1713522 ADAPTER (EUROPEAN MODELS)
1
2
1023100 COUPLER
1
3
1025100 PLUG, CAP
1
4
1035100 HOSE, 4" DIA. X 10' LONG
1
5
1027100 LEAF TRAY
1
6
1030100 NOZZLE
1
7
1024100 RING, NOTCHED, 5" DIA. X 3" LONG
1
8
1960294 NUT, HEX FLANGE, 1/4-20
1
9
1921319 WASHER, 1/4
2
10
6041612 BOLT, PHILLIPS TRUSS HD, 1/4-20 X 1-1/2
1
11
1026100 HANDLE
1
12
1028100 GRIP, HANDLE
1
13
5001612 DECAL, DANGER
1
14
1709467 HOPPER LID, RED
1
15
1919326 WASHER, FLAT, 5/16
3
1732039 DECAL, DANGER
1
-
Page 28
PART # DESCRIPTION
800-345-6007
Parts Explosions & Listings
1692327 tow bar kit (optional accessory)
3
9
6
8
4
5
2
7
5
5
1
KEY #
QTY.
1
1713352 BENT ARM ASSEMBLY
1
2
1713414 ROD ASSEMBLY
1
3
1713357 ROD HOLDER ASSEMBLY
1
4
1710726 PIN, CLEVIS, 5/16 X 1-1/2
4
5
1918196 PIN, QUICK, 3/32 X 1-7/8
5
6
1925205 BOLT, HEX HD CAPSCREW, 5/16-18 X 5/8 GR5
1
1423B BOLT, HEX HD CAPSCREW, 5/16-18 X 2 GR5
1
7
800-345-6007
PART # DESCRIPTION
8
1919438 NUT, HEX LOCK, 5/16-18
1
9
118053 PIN, ROUND HD, 3/8 X 2
1
Page 29
Page 30
DECLARATION DE CONFORMITE
DECLARATION DE CONFORMIDAD
DICHIARAZIONE DI CONFORMITÀ
9060140
MODELLO NR.
N° DE PRODUCTO
PRODUKTNR.
PRODUKTIONSNR.
PRODUKT-NR.
.
°
EARTHQUAKE
DESCR.
Signed
Kirk Hyatt
CHIPPER EARTHQUAKE 5.5 HP BRIGGS EURO
Declares that products listed below comply to 98/37/EC + 89/336/EEC
Déclare que les produits énumérés ci-dessous sont conformes à: 98/37/EC + 89/336/EC
Erklärt, dass die unten aufgeführten Produkte mit den Vorschriften übereinstimmen 98/37/EC + 89/336/EC
Erklærer, at nedenstående produkter opfylder ... 98/37/EC + 89/336/EC
Declara que los productos relacionados mas abajo cumplen con: 98/37/EC + 89/336/EC
Verklaart dat onderstaande produkten overeenkomen met: 98/37/EC + 89/336/EC
Si dichiara che i prodotti sotto elencati sono conformi a: 98/37/EC + 89/336/EC
PRODUCT NO.
N° DE FABRICATION
ÜBEREINSTIMMUNGSERKLÄRUNG
VERKLARING VAN OVEREENKOMST
109
LIVELLO DI EMISSIONI ACUSTICHE
GARANTITO A:
Date
106
MISURATO EMISSIONI
SONORA IMPORTO :
June 2, 2006
DOCCS6
FORM NO. 1714848-14
AFGEMETEN GESEVENS
GELVIDSSTERKTE AARTAL :
MEASURED SOUND-POWER LEVEL
MESURER NIVEAU DE PUISSANCE
ACOUSTIQUE TAILLE :
GEMESSENER
SCHALLEISTUNGSPEGEL
MÅLE LYDSTYRKE BELØB :
Product Manager
Ardisam, Inc.
Cumberland, WI USA
GARANTIZA UN NIVEL DE SONORIDAD:
GEGARANDEERD GELUIDSNIVO:
GUARANTEED SOUND-POWER LEVEL
NIVEAU DE PUISSANCE
ACOUSTIQUE GARANTI:
GARANTIERTER
SCHALLEISTUNGSPEGEL:
GARANTERET STØJNIVEAU:
Declares that products listed below comply to 2000/14/EC, ANNEX V
Déclare que les produits énumérés ci-dessous sont conformes à: 2000/14/EC, ANNEX V
Erklärt, dass die unten aufgeführten Produkte mit den Vorschriften übereinstimmen 2000/14/EC, ANNEX V
Erklærer, at nedenstående produkter opfylder ... 2000/14/EC, ANNEX V
Declara que los productos relacionados mas abajo cumplen con: 2000/14/EC, ANNEX V
Verklaart dat onderstaande produkten overeenkomen met: 2000/14/EC, ANNEX V
Si dichiara che i prodotti sotto elencati sono conformi a: 2000/14/EC, ANNEX V
Ardisam Manufacturing, Inc. • 1690 Elm Street • Cumberland, WI U.S.A. 54829
DECLARATION OF CONFORMITY
KONFORMITETSERKLÆRING
5.5 hp Certificate of Conformity
800-345-6007
800-345-6007
DECLARATION DE CONFORMITE
DECLARATION DE CONFORMIDAD
DICHIARAZIONE DI CONFORMITÀ
9080140
MODELLO NR.
N° DE PRODUCTO
PRODUKTNR.
PRODUKTIONSNR.
PRODUKT-NR.
.
°
EARTHQUAKE
DESCR.
Signed
Kirk Hyatt
CHIPPER EARTHQUAKE 8 HP BRIGGS EURO
Declares that products listed below comply to 98/37/EC + 89/336/EEC
Déclare que les produits énumérés ci-dessous sont conformes à: 98/37/EC + 89/336/EC
Erklärt, dass die unten aufgeführten Produkte mit den Vorschriften übereinstimmen 98/37/EC + 89/336/EC
Erklærer, at nedenstående produkter opfylder ... 98/37/EC + 89/336/EC
Declara que los productos relacionados mas abajo cumplen con: 98/37/EC + 89/336/EC
Verklaart dat onderstaande produkten overeenkomen met: 98/37/EC + 89/336/EC
Si dichiara che i prodotti sotto elencati sono conformi a: 98/37/EC + 89/336/EC
PRODUCT NO.
N° DE FABRICATION
ÜBEREINSTIMMUNGSERKLÄRUNG
VERKLARING VAN OVEREENKOMST
110
Date
108
MISURATO EMISSIONI
SONORA IMPORTO :
DOCCS8
FORM NO. 9080140
August 23, 2006
AFGEMETEN GESEVENS
GELVIDSSTERKTE AARTAL :
MEASURED SOUND-POWER LEVEL
MESURER NIVEAU DE PUISSANCE
ACOUSTIQUE TAILLE :
GEMESSENER
SCHALLEISTUNGSPEGEL
MÅLE LYDSTYRKE BELØB :
Product Development Manager
Ardisam, Inc.
Cumberland, WI USA
LIVELLO DI EMISSIONI ACUSTICHE
GARANTITO A:
GARANTIZA UN NIVEL DE SONORIDAD:
GEGARANDEERD GELUIDSNIVO:
GUARANTEED SOUND-POWER LEVEL
NIVEAU DE PUISSANCE
ACOUSTIQUE GARANTI:
GARANTIERTER
SCHALLEISTUNGSPEGEL:
GARANTERET STØJNIVEAU:
Declares that products listed below comply to 2000/14/EC, ANNEX V
Déclare que les produits énumérés ci-dessous sont conformes à: 2000/14/EC, ANNEX V
Erklärt, dass die unten aufgeführten Produkte mit den Vorschriften übereinstimmen 2000/14/EC, ANNEX V
Erklærer, at nedenstående produkter opfylder ... 2000/14/EC, ANNEX V
Declara que los productos relacionados mas abajo cumplen con: 2000/14/EC, ANNEX V
Verklaart dat onderstaande produkten overeenkomen met: 2000/14/EC, ANNEX V
Si dichiara che i prodotti sotto elencati sono conformi a: 2000/14/EC, ANNEX V
Ardisam Manufacturing, Inc. • 1690 Elm Street • Cumberland, WI U.S.A. 54829
DECLARATION OF CONFORMITY
KONFORMITETSERKLÆRING
8 hp Certificate of Conformity
Page 31
ARDISAM
.com
Visit www.ardisam.com and discover more innovations that will
benefit you throughout the year.
Earthquake, Division of Ardisam, Inc.
1690 Elm Street; P.O. Box 666
Cumberland, Wisconsin 54829
800-345-6007 · Fax (715) 822-2223
E-mail: [email protected]