DFI DT122-CR Pre-Configured System & Chassis Installation guide

DT122-CR

Installation Guide

Package Contents

• 1 DT122-CR system unit

• 1 HDD drive bay kit

• 1 Quick Installation Guide

• 1 CD disk includes:

- Drivers/Manual

Optional Items

• Power Cord www.dfi .com

1

Front View

Reset Button

Power LED

Power Button

HDD LED

Rear View

PS/2 Mouse/KB

COM 1

Expansion slot

LAN 1-2

USB 2.0

HDMI

DVI-I

USB 3.0

Line-out Line-in/Surround

Mic-in/Center+Subwoofer

2

PROCESSOR

CHIPSET

LAN

COM

DISPLAYS

USB

AUDIO

Key Features

DT122-CR

3rd/2nd Generation Intel

®

Core

TM

processors

Intel

®

QM77

2 LAN ports

1 COM port

2 DVI-I (1 DVI-D Signal), 1 HDMI

4 Type A USB 3.0/2.0/1.1 ports

2 Type A USB 2.0/1.1 ports

2 Type A USB 2.0/1.1 ports (optional)

Mic-in/Center+Subwoofer, Line-in/Surround, Line-out

3

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices connected to it has been powered-off.

2. Disconnect all power cords and cables.

3. The 4 mounting screws on the sides of the system are used to secure the cover to the chassis. Remove these screws and then put them in a safe place for later use.

Mounting screw

Mounting screw

4

4. After removing the mounting screws, slide the cover backwards.

Slide the Cover Backward

5. The DIMM sockets and SATA drive bay are readily accessible after removing the chassis cover.

SODIMM socket

2.5"/3.5" SATA drive bay

5

Installing a 2.5" or 3.5" SATA

Drive

lnstalling a 2.5" SATA Drive

1. Remove the 4 mounting screws that secure the drive bay to the system.

Mounting screw

Drive bay

Mounting screw

2. Turn to the other side of the drive bay and remove the

4 mounting screws that secure the HDD brackets to the drive bay.

Drive bay

Mounting screw

6

3. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket and then use the provided mounting screws to secure the drive in place.

Mounting screw

Mounting screw

HDD bracket

SATA drive

7

4. Turn to the other side of the drive bay. Use the provided mounting screws from step 2 to secure the

SATA drive bay assembly onto the drive bay.

Drive bay

Mounting screw

Mounting screw

5. Place the SATA drive bay assembly into the chassis.

Secure the SATA drive bay with the mounting screws you removed in step 1.

Mounting screw

Mounting screw

8

6. Connect the SATA data cable and SATA power cable to the connectors on the SATA drive.

SATA power cable

SATA data cable

9

lnstalling a 3.5" SATA Drive

1. Remove the 4 mounting screws that secure the drive bay to the system.

Mounting screw

Drive bay

Mounting screw

2. Insert the spacer into the anti-shock bumper. You will fi nd the spacers in the HDD drive bay kit that comes with the DT122 package.

spacer spacer

Drive bay

3. Place the SATA drive on the drive bay. Align the mounting holes of the SATA drive with the mounting holes on the drive bay.

SATA drive

Drive bay

10

4. Use the provided mounting screws to secure the SATA drive onto the drive bay.

Mounting screw

Mounting screw

Drive bay

5. Place the drive bay into the chassis. Secure the drive bay with the mounting screws you removed in step 1.

Mounting screw

Mounting screw

6. Connect the SATA data cable and SATA power cable to the connectors on the SATA drive.

SATA data cable

SATA power cable

11

Installing the PCI or PCIe x16

Expansion Card

Important:

When inserting the riser card, please select a card within 175mm (as shown on the next picture).

1. The PCIe x16 slot on the motherboard is used to insert a TS200-1P and TS200-1E riser card.

To install the expansion card, you need to remove the mounting bracket and the mounting screw that secure the bracket to the chassis and then remove the bracket. Put the screw and the brackets in a safe place for later use.

Mounting screw

Mounting bracket

12

Bracket

Mounting bracket and mounting screw

T200-1P

PCI slot

T200-1E

PCIe x16 slot

13

2. Insert the Expansion card with a bracket into the PCI or PCIe x16 slot that is on the riser card. Replace the screw you removed in step 1 to secure the bracket in place.

PCI

Bracket

Mounting bracket and mounting screw

Expansion card

Rear view

Note:

The Expansion card used in the above illustrations may not resemble the actual cards. These illustrations are for reference only.

14

Mounting Options

Wall mount

There are 2 types of wall mount brackets:

A

Type A wall mount kit include:

• 2 type A wall mount brackets

1. If the mounting screw has been previously attached to the top cover of the system, please remove them fi rst.

Mounting screw

Mounting screw

15

2. At the sides of the system, use the mounting screws removed in step 1 to secure the wall mount brackets on each side of the system.

Wall mount bracket

Mounting screw

Wall mount bracket

319.00

Ø5.00

Ø3.60

4-#6-32

Ø4.00

Ø8.50

300.00

16

Type B wall mount kit include:

• 2 type B wall mount brackets

1. The 4 mounting holes on the sides of the system are used to mount the type B wall mount bracket.

2. Use the provided mounting screws to secure the type

B wall mount brackets on each side of the system.

Wall mount bracket

Wall mount bracket

17

5.00

R2.50

300.00

335.00

360.00

Ø8.50

5.00

16

R2.50

55.00 78.00

18

Board Layout and Jumper Settings

USB 2.0

COM1 RS232/Power select (JP1)

1

PS/2

Mouse/KB

USB 8

USB 9

2

JP1

6

1 5

1 1

2

1

Chassis intrusion

PS/2 power select (JP2)

9

2 1

COM6

6

5

COM1 RS232/422/485 select ( JP4 )

9

2 1

COM5

COM 1

HDMI

USB 8-9 power select ( JP8 )

9 9

1

2 1

COM4

2 1

COM3

13

1

Power-on select ( JP7 )

DDR3_2 SODIMM

DDR3_1 SODIMM

Socket G2 rPGA 988B

ATX Power

9

COM2

12

24

2 6

6

2 1

2

5

1

COM2 RS232/

422/485 Select

(JP5)

Buzzer

1 5

COM2 RS232/Power select (JP3)

DVI-I

DVI-I

1

CPU fan

SPI Flash BIOS

System fan

SW1

1

2

ON

11

19

2 1

DIO

1

Front panel

1

1

USB 0-1/ 2-3 power select (JP6)

Battery

SATA 0

LAN 1

USB3.0 (0-1)

SATA 3.0

SATA 1

1

LVDS LCD panel

2 1

SATA 4

1

LAN 2

USB3.0 (2-3)

Mini PCIe

Backlight level (JP11)

10 9

Line-in/ Surround

Line-out

2 1

Mic-in/ Center+Subwoofer

Front audio

1

S/PDIF

LCD/Inverter power

1

1

40 39

PCIe x16

1

5

Intel

QM77

2

6

SATA 5

1

1

Standby

Power LED

Clear CMOS

(JP10)

9

10

9

SATA 2.0

USB 6-7

1

USB 4-5

USB 2.0

1

2

1

2

PCIe x1

Clear CMOS

Normal (default)

Clear CMOS

JP10

1-2 On

2-3 On

USB Power: 0-1/2-3 (JP6)/ 8-9 (JP8)

+5V (default) 1-2 On

+5V_standby 2-3 On

PCIe x1

COM 1 (JP4), COM 2 (JP5) RS232/RS422/RS485 Select

RS232 (default) 1-2 On

RS422 Full Duplex

RS485

3-4 On

5-6 On

Power-on Select JP7

PS/2 Power Select

+5V (default)

+5V_standby

JP2

1-2 On

2-3 On

COM 1 (JP1), COM 2 (JP3) RS232/Power

RS232 (default) 1-3, 2-4 On

RS232 with power 3-5 (+5V),

4-6 (+12V) On

Backlight Level Select

+5V (default)

+3V3

JP11

1-2 On

2-3 On

Auto Power-on

Panel Power Select

+12V

+5V

+3.3V (default)

PCIe x16 Supported Confi gurations

One PCIe x8, Two PCIe x4

Two PCIe x8

One PCIe x16 (default)

2-3 On

JP9

1-2 On

3-4 On

5-6 On

SW1

1-2 On

1 On, 2 Off

1-2 Off

19

934-DT1220-200G

A26212342