Masterflex L/S Precision 07528-10, 07528-20, 07528-30 Variable Speed Console Drive Operating Manual

Masterflex L/S Precision 07528-10, 07528-20, 07528-30 Variable Speed Console Drive Operating Manual

Below you will find brief information for Variable Speed Console Drive L/S Precision 07528-10, Variable Speed Console Drive L/S Precision 07528-20 and Variable Speed Console Drive L/S Precision 07528-30. These drives control the speed of MASTERFLEX Pump Heads to provide flow rates from 0.06 to 3400 mL/min. The 300 and 600 rpm L/S Precision Variable-Speed Console drives can mount up to two (2) MASTERFLEX Pump Heads or other pumps adapted to MASTERFLEX drives. The 100 rpm L/S Precision Variable-Speed Console drive can mount up to four (4) MASTERFLEX Pump Heads or other pumps adapted to MASTERFLEX drives.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Masterflex L/S Precision Variable Speed Console Drive 07528-10, 07528-20, 07528-30 Operating Manual | Manualzz
®
®
OPERATING MANUAL:
L/S ® PRECISION
VARIABLE SPEED
CONSOLE DRIVES
Model Nos.
MASTERFLEX® L/S® 07528-10
07528-10
07528-20
07528-30
A-1299-1059
Edition01
®
1-800-MASTERFLEX (627-8373) (U.S. and Canada only) • 11 (847) 549-7600 (Outside U.S.)
(847) 549-7600 (Local) • www.masterflex.com • [email protected]
Preface
© 2011 Thermo Fisher Scientific Inc. All rights reserved.
MASTERFLEX and L/S – Reg TM Cole-Parmer
NORPRENE, PHARMED and TYGON – Reg TM Saint-Gobain Performance Plastics Corp.
Trademarks bearing the
® symbol in this publication are registered in the U.S. and in other countries.
ORIGINAL INSTRUCTIONS
A-1299-1059
01
17651
110520
First Edition
RW
REV
ECR/ECN
DATE
DESCRIPTION
By
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
ii
Preface
Safety Precautions
SAFETY
PRECAUTIONS
DANGER: Remove power from the pump before any
cleaning operation is started.
WARNING: Remove power from the pump before attempting
any maintenance.
WARNINGS: Tubing breakage may result in fluid being sprayed
from pump. Use appropriate measures to protect operator and
equipment.
Turn Pump System off before removing or installing tubing.
Fingers or loose clothing could get caught in drive mechanism.
CAUTIONS: When changing flow direction, allow the pump to
come to a complete stop before starting again. Failure to do
so could cause permanent damage to the motor.
Replace the fuse only with one of the same type and rating.
The fuse rating and type are stated on the rear panel.
CAUTION: To avoid electrical shock, the power cord
protective grounding conductor must be connected to ground.
Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the
instructions, the protection provided by the equipment may
be impaired.
Explanation of
Symbols
CAUTION: Risk of Danger. Consult Operator’s manual for nature
of hazard and corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor
while pump is in operation. Stop pump before loading or
unloading tubing.
CAUTION: Hot Surface. Do not touch.
CAUTION: Risk of electric shock. Consult Operator’s manual for
nature of hazard and corrective actions.
WARNING:
Product Use
Limitation
This product is not designed for, nor intended for use in
patient connected applications; including, but not limited to,
medical and dental use, and accordingly has not been
submitted for FDA approval.
This product is not designed for, nor intended for use in
hazardous duty areas as defined by ATEX or the NEC (National
Electrical Code); including, but not limited to use with
flammable liquids.
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
iii
Preface
Safety
1. Read instructions before operating the unit.
2. Observe safety precautions at all times, especially when pumping
dangerous liquids.
3. If the pump runs unusually noisy or if bunching of the tubing in the
pump can be observed, make sure the tubing is clamped down tightly
and/or replace it with a new piece of tubing.
4. The L/S Precision Variable-Speed Console Drives must be wellgrounded at all times.
5. The L/S Precision Variable-Speed Console Drives are equipped with a
current-limiting circuit that will shut the motor down if any of the
following conditions exist:
a. Tubing that is too hard is loaded in the pump.
b. Incorrect tubing size or wall thickness is loaded in the pump.
c. Tubing is improperly loaded into the Pump Head.
6. The unit is fused and grounded to protect the operator in the event of
short circuits that could be caused by liquid entering the case.
CAUTION: Replace the fuse only with one of the same type
and rating. The fuse rating and type are stated on the
rear panel.
7. The L/S Precision Variable-Speed Console Drives should not be used
in outdoor or hazardous locations.
iv
L/S Precision Variable-Speed Console Drives Operating Manual
Cole-Parmer
Table of Contents
Page
Cole-Parmer
Section 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Controls, Indicators and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Section 2
INSTALLATION AND SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Before Starting Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Mounting the Pump Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Section 3
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Inserting Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Tubing Inspection and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Pump Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Keypad Lockout Enable/Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
External Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
External Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Section 4
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Motor Gear and Brush Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Section 5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Section 6
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Section 7
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Section 8
WARRANTY, PRODUCT RETURN and TECHNICAL ASSISTANCE . . . .8-1
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
Product Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
L/S Precision Variable-Speed Console Drives Operating Manual
v
Figures
Figures
Page
Controls, Indicators and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
DB9 Pin Configuration with Wiring Scheme . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Motor Gear and Brush Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
vii
Section 1
General Description
Introduction
The L/S Precision Variable-Speed Console Drives control the speed of
MASTERFLEX® Pump Heads to provide flow rates from 0.06 to 3400 mL/min.
The 300 and 600 rpm L/S Precision Variable-Speed Console drives can
mount up to two (2) MASTERFLEX Pump Heads or other pumps
adapted to MASTERFLEX drives.
The 100 rpm L/S Precision Variable-Speed Console drive can mount up to
four (4) MASTERFLEX Pump Heads or other pumps adapted to
MASTERFLEX drives.
Application Solutions
Cole-Parmer
Advantages of Peristaltic Pumps:
•
Handle abrasive slurries and corrosive fluids with minimal wear. Ideal
for titanium dioxide or diatomaceous earth filter aid applications.
•
Low maintenance; sealless and valveless design
•
Valveless design prevents clogging.
•
Inner surfaces are smooth and easy to clean.
•
Contamination free; fluid contacts only the tubing or tube material.
•
Suction lift and priming up to 8.8m water column at sea level.
•
Low shearing for handling the most shear sensitive of fluids such as
latex or fire fighting foam.
•
Capable of running dry and pumping fluids with high quantities of
entrained air, such as black liquor soap.
•
High volumetric efficiency allows operation in metering or dosing
applications where high accuracy is required.
•
Handles extremely viscous fluids.
•
Availability of tubing and tube materials that are suitable for food and
pharmaceutical use.
L/S Precision Variable-Speed Console Drives Operating Manual
1-1
Section 1
Introduction
C
Controls, Indicators
and Connectors
D
B
E
G
F
A
Figure 1-1. Controls, Indicators and Connectors
A. POWER (ON/OFF) SWITCH: Turns the unit ON or OFF.
B. SPEED KEYS: Sets the speed of the pump. The higher the number, the
faster the speed of the pump. When the speed key is depressed the
smallest speed units change first followed by an increasing rate of change.
C. FLOW DIRECTION KEY: Sets the direction of pump rotation
Clockwise/Counterclockwise. An LED annunciator indicates the
active direction. The motor is brought to a controlled stop before
reversing direction.
D. INTERNAL/EXTERNAL KEY: Changes the drive operation mode.
Internal (Local) operation from the front panel keypad is designated
by INT, external (Remote) operation is designated by EXT. In INT
mode, START/STOP, FLOW DIRECTION, and SPEED keys on the
front panel determine operating state. Depression and release of keys
enables toggling between the two operating states.
E. START/STOP KEY: Upon depression, key toggles the motor
ON/OFF during INT mode. This key will not start the drive if in
EXT mode. If pressed while operating in EXT mode (stop desired),
the button will always stop the drive and a toggle of the EXT
Start/Stop is required to restart the drive.
F. EXTERNAL/REMOTE CONNECTOR: Utilized to connect wiring
for remote control operation with a DB9 connector.
G. IEC Power Entry Module/Line Cord: Utilized to connect line cord to
drive. See page 4-1 for alternative cords.
1-2
L/S Precision Variable-Speed Console Drives Operating Manual
Cole-Parmer
Section 2
Before Starting Drive
Installation and Setup
•
The drive should be mounted on a flat horizontal surface. Up to a
maximum of two (2) Pump Heads can be added for 300 rpm and 600
rpm drives or four (4) Pump Heads for 100 rpm drives.
•
The ambient air temperature should not exceed 104° F (40° C) and
adequate air flow should be provided for.
•
The drives are provided with a grounded plug. If used in a GFCI
protected circuit, nuisance tripping may occur.
•
Tubing should be clean and routed so that bend radii are at a
minimum four (4) times the tube diameter and as short as possible.
WARNING: Turn drive off before removing or installing tubing.
Fingers or loose clothing could get caught in drive mechanism.
•
Use a tube size of appropriate diameter for the flow rate and
viscosity required.
•
For tubing selection and compatibility, see Tubing Selection Guide
within this CD.
•
For Pump Head information, see Pump Head datasheets within
this CD.
•
Before cleaning or conducting maintenance on unit remove power
from the drive.
DANGER: High voltages exist and are accessible. Use extreme
caution when servicing internal components.
Mounting the
Pump Head
Cole-Parmer
Mount Pump Head and load tubing (See Pump Head datasheets within
this CD). Check to ensure that rollers are clean and free of defects.
L/S Precision Variable-Speed Console Drives Operating Manual
2-1
Section 3
Inserting Tubing
Operation
WARNINGS: Tubing breakage may result in fluid being
sprayed from pump. Use appropriate measures to protect
operator and equipment.
Turn Pump System off before removing or installing tubing.
Fingers or loose clothing could be caught in the pump
mechanism.
CAUTION: To avoid electrical shock, the power cord protective grounding conductor must be connected to ground. Not
for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the
instructions, the protection provided by the equipment
may be impaired.
Tubing Inspection and
Replacement
Tubing should be inspected periodically for tears, cracks, cut marks,
abrasions, inability to hold pressure, bubbles in the flow stream and
reduction or loss of flow.
Tubing life may be extended by periodically moving the worn tubing
inside the occlusion bed of the pump to the outside of the occlusion bed
to the suction side of the pump. This will avoid excessive tubing wear at
any specific point.
Always move the worn tubing to the suction side of the pump.
Pump Controls
CAUTION: When changing flow direction, allow the pump
to come to a complete stop before starting again. Failure to
do so could cause permanent damage to the motor.
1. Make sure the speed is set to the minimum setting.
2. Turn the power switch ON. Increase the speed to start the pump
action. The higher the rpm setting, the faster the speed of the pump.
3. The L/S Precision Variable-Speed Console Drives are self-priming. To
begin pumping, select a flow direction with the flow direction button,
insert the intake and output tubing into a reservoir, and turn the unit
ON. Prime the tubing for at least 5 minutes. If accurate flow control is
important, allow the pump to prime for approximately 20 minutes for
more stable flow conditions.
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
3-1
Section 3
Operation
Keypad Lockout
Enable/Disable
External Operation
Press and hold the INT/EXT key. After five (5) seconds, display will
change to all dashes. Release INT/EXT key and press UP ARROW key (▲)
five (5) times. Repeat this process to unlock the keypad. When the keypad
is locked out, display will change to display all dashes (- - - - -) when a key
is depressed.
Models are equipped with inputs that can be controlled by external signals
connected at the rear panel 9-pin “D” shell connector. The external inputs
permit control of the pump by remote equipment or accessories. Figure 3-1
indicates the signal locations in the connector.
Note: Jumpers “A” and “B” are
optional. See page 3-3 External
Inputs for correct usage.
Pin No.
Description
1
Speed Control Voltage Input (0–10V) (+) input
2
Speed Control Current Input (4–20 mA) (+) input
3
Speed Control Input Reference Common
4
Local/Remote Speed Control
5
Local/Remote Speed Control Reference
6
Start/Stop and CW/CCW Reference
7
Start/Stop (+) Control
8
CW/CCW
9
Chassis (Earth) Ground
Figure 3-1. DB9 Pin Configuration with Wiring Scheme
3-2
L/S Precision Variable-Speed Console Drives Operating Manual
Cole-Parmer
Section 3
Operation
External Inputs
The front INT/EXT key enables external functions. Switching to INT on
the display disables the external functions, allowing the front panel
controls to operate the pump.
When the INT/EXT key is in the EXT position, starting and stopping the
pump is controlled by an external contact closure between pins 6 and 7
(Jumper B), and the pump speed is determined by an externally supplied
0–10V or 4–20 mA source. Connection must be made between pins 6 and
7 to Start/Stop the drive and a control voltage greater than 0V between
pins 1 and 3 or a control current greater than 4 mA between pins 2 and 3
must be applied for the pump to run.
If setting the speed from the front panel is desired with external Start/Stop
contact operation, the INT/EXT key must again be in the EXT position.
In addition, Jumper A should be in place. Jumper A connects pin 4 of the
“D” shell connector (Local/Remote) to pin 5 (Local/Remote Reference).
Start/Stop will then be controlled from the rear panel (Jumper B), and the
pump speed will be controlled from the front panel. The accessory
Footswitch (part no. 77595-35) and Handheld Remote Controller
(part no. 07528-80) are connected internally in this way.
NOTE: The signal common for the speed control voltage and current
inputs is not referenced to earth ground.
The START/STOP (pin 7), CW/CCW (pin 8) and Local/Remote (pin 4)
are digital inputs. They are internally pulled up to +5 V with respect to
earth ground via pins 5 and 6. They can alternately be driven with open
collector logic. For increased noise immunity, use of contact closures is
recommended.
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
3-3
Section 4
Replacement Parts
Maintenance
WARNING: Remove power from the pump before attempting any
maintenance.
Description
Cole-Parmer
Part Number
Brushes (set of 2)
07520-04
Brush Cap Holder
07520-03
Fuse-T3.15A, 5 x 20 mm
77500-25
Gear Service Kit (600 & 300)
07553-06
Gear Only (600 & 300 rpm)
07553-09
Gear Service Kit (100 rpm)
07553-08
Ferrite, Line Cord Snap-on, (CE Required)
B-3689-CR
Line Cord, Australia
50001-60
Line Cord, Denmark
50001-62
Line Cord, India
50001-64
Line Cord (115V), United States
50001-68
Line Cord, Israel
50001-69
Line Cord, Europe
50001-70
Line Cord, England
50001-72
Line Cord, Switzerland
50001-74
Line Cord, Italy
50001-76
Line Cord (230V), United States
50001-78
Line Cord, China
50001-79
L/S Precision Variable-Speed Console Drives Operating Manual
4-1
Section 4
Section title
Fuse Replacement
1. Place the power switch in the off position.
2. Disconnect the AC power input line cord from the receptacle.
3. Remove and check the fuse and replace if defective.
A
B
Figure 4-1. Fuse Replacement
Item
A
B
4-2
Description
IEC Power Entry Module / Line Cord
3.15A (5×20 mm) Fuse – Do Not Substitute
L/S Precision Variable-Speed Console Drives Operating Manual
Cole-Parmer
Section 4
Section title
Motor Gear and Brush
Replacement
E
A
B
F
C
D
A.
B.
C.
D.
E.
F.
6-600 & 3-300 rpm gear assembly (included in service kit 07553-06)
Gasket
1-100 rpm gear set (included in service kit 07553-08)
Gear Case cover assembly
Brush Cap
Motor Brush (set of two included in 07520-04)
Figure 4-2. Motor Gear and Brush Replacement
Cleaning
WARNING: Remove power from the pump before any cleaning
operation is started.
Keep the drive enclosure clean with mild detergents. Do not immerse or
use excessive fluid when cleaning.
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
4-3
Section 5
Troubleshooting Chart
Troubleshooting
Symptom
Remedy
Unit will not turn on
If the unit is plugged into a GFCI protected circuit verify
that the circuit has not been tripped or reset the circuit.
Verify that the unit is plugged into a functioning outlet.
Verify that the power cord is firmly attached to the unit.
Verify that the fuse for the incoming voltage is not
blown (located in the slot next to the power cord).
Unit will turn on
but pump will not spin
Check the tubing. Tubing should be snug, but not tight,
against the rollers.
Verify that the mode EXT/INT is set correctly.
Cole-Parmer
Error XX is displayed on the screen
Err's 3 & 10, check pump for obstructions, all other Errs
return unit for repair.
Unit will turn on but display would
dim and pump will not spin
Verify that the incoming voltage meets the required
minimum of 90Vrms.
Unit vibrates excessively when
pump is running
Check that the tubing was loaded properly.
L/S Precision Variable-Speed Console Drives Operating Manual
5-1
Section 6
Accessories
Cole-Parmer
Accessories
1.
Footswitch w/DB-9 male
77595-35
2.
Handheld Remote Controller
07528-80
3.
DB-9 External Control Connector
07595-45
4.
DB-9 Remote control cable, 25 FT.
07595-47
5.
Tilt Bail
07523-98
L/S Precision Variable-Speed Console Drives Operating Manual
6-1
Section 7
Specifications
Output:
Speed:
07528-30
07528-20
07528-10
Torque, Maximum:
300 & 600 rpm models
100 rpm models
Input:
Operating Voltage/Frequency:
External Inputs:
START/STOP, CW/CCW,
Remote/Local Speed Control
Voltage input
Accuracy:
Current input
Accuracy:
Environment:
Operating Temperature:
Storage Temperature:
Humidity:
Altitude:
Pollution Degree:
Construction:
Dimensions (L × W × H):
Weight:
Color:
Material:
Enclosure Rating:
Cole-Parmer
1 - 100 rpm
3 - 300 rpm
6 - 600 rpm
180 oz-in (13 kg•cm), 540 oz-in Starting
360 oz-in (26 kg•cm), 1080 oz-in Starting
90-260Vrms, 50/60 Hz, 2.2A @ 115Vrms,
1.1A @ 230 Vrms
Contact closure
0–10V DC @ 10 kohm,
±0.5% Full Scale
4–20 mA @ 250 ohm,
±0.5% Full Scale
32 to 104°F (0 to 40°C)
-13 to 149°F (-25 to 65°C)
10% to 90% non-condensing
Less than 6562 ft (2000 m)
Pollution degree 2 (indoor use–lab, office)
10.5 in × 8 in × 8 in
(267 × 203 × 203 mm)
6.9 kgs (15.2lbs)
Light Grey (5% Black)
Aluminum, ABS plastic and vinyl
IP33 per IEC-60529
L/S Precision Variable-Speed Console Drives Operating Manual
7-1
Section 7
Warranty, Product Return and
Technical Assistance
Compliance:
7-2
L/S Precision Variable-Speed Console Drives Operating Manual
UL 61010-1, CAN/CSA-C22.2 No. 61010-1
This product has been tested to the requirements of
CAN/CSA-C22.2 No. 61010-1, second edition,
including Amendment 1, or a later version of the
same standard incorporating the same level of
testing requirements.
(For CE Mark):
EN61010-1: (EU Low Voltage Directive) and
EN61326: (EU EMC Directive)
Cole-Parmer
Warranty, Product Return and
Technical Assistance
Section 8
Warranty
Use only MASTERFLEX precision tubing with MASTERFLEX pumps to
ensure optimum performance. Use of other tubing may void applicable
warranties.
This product is warranted against defects in material or workmanship, and
at the option of the manufacturer or distributor, any defective product will
be repaired or replaced at no charge, or the purchase price will be refunded
to the purchaser, provided that: (a) the warranty claim is made in writing
within the period of time specified on the warranty card, (b) proof of
purchase by bill of sale or receipted invoice is submitted concurrently with
the claim and shows that the product is within the applicable warranty
period, and (c) the purchaser complies with procedures for returns set
forth in the general terms and conditions contained in the manufacturer's
or distributor's most recent catalog.
This warranty shall not apply to: (a) defects or damage resulting from: (i)
misuse of the product, (ii) use of the product in other than its normal and
customary manner, (iii) accident or neglect, (iv) improper testing,
operation, maintenance, service, repair, installation, or storage, (v)
unauthorized alteration or modification, or (b) post-expiration dated
materials.
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
PURCHASER, AND THE MANUFACTURER AND DISTRIBUTOR
DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS,
IMPLIED, OR STATUTORY, INCLUDING WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE,
AGENT, OR REPRESENTATIVE OF THE MANUFACTURER OR
DISTRIBUTOR IS AUTHORIZED TO BIND THE
MANUFACTURER OR DISTRIBUTOR TO ANY OTHER
WARRANTY. IN NO EVENT SHALL THE MANUFACTURER OR
DISTRIBUTOR BE LIABLE FOR INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL DAMAGES.
The warranty period for this product is two (2) years from date of purchase.
Cole-Parmer
L/S Precision Variable-Speed Console Drives Operating Manual
8-1
Section 8
Warranty, Product Return and
Technical Assistance
Product Return
Technical Assistance
8-2
To limit charges and delays, contact Cole-Parmer or authorized seller for
authorization and shipping instructions before returning the product, either
within or outside of the warranty period. When returning the product, please
state the reason for the return. For your protection, pack the product
carefully and insure it against possible damage or loss. Any damages resulting
from improper packaging are your responsibility.
If you have any questions about the use of this product, contact the ColeParmer or authorized seller.
L/S Precision Variable-Speed Console Drives Operating Manual
Cole-Parmer
®
®
®
®
1-800-MASTERFLEX(627-8373)(U.S.andCanadaonly)
11(847)549-7600(OutsideU.S.)
(847)549-7600(Local)
www.masterflex.com
[email protected]
PrintedinU.S.A.

advertisement

Key Features

  • Flow rates from 0.06 to 3400 mL/min
  • Mount up to two Pump Heads (300 and 600 rpm models)
  • Mount up to four Pump Heads (100 rpm models)
  • Handles abrasive slurries and corrosive fluids
  • Low maintenance, sealless and valveless design
  • Valveless design prevents clogging
  • Inner surfaces are smooth and easy to clean
  • Contamination free, fluid contacts only the tubing or tube material
  • Suction lift and priming up to 8.8m water column at sea level

Frequently Answers and Questions

How do I change the flow direction of the pump?
Allow the pump to come to a complete stop before starting again.
What is the maximum torque of the 300 and 600 rpm models?
180 oz-in (13 kg•cm), 540 oz-in Starting
What is the maximum torque of the 100 rpm models?
360 oz-in (26 kg•cm), 1080 oz-in Starting
What is the operating voltage and frequency?
90-260Vrms, 50/60 Hz, 2.2A @ 115Vrms, 1.1A @ 230 Vrms

Related manuals

Download PDF

advertisement