Installation Instructions SPREAD LAVATORY FAUCETS

Installation Instructions SPREAD LAVATORY FAUCETS
Installation
Instructions
6500 6530
6502 6532
SPREAD LAVATORY
FAUCETS
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
Certified to comply with ANSI A112.18.1
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
1
CAUTION
60186 REV.1.8 (2/16)
Turn off water at
main supply.
CONVENTIONAL SPOUT
CONVENTIONAL OR GN SPOUT ASSEMBLY
Insert SPOUT SHANK (1, 1a) through
center hole of SINK, making sure
RUBBER GASKET (2, 2a) is properly positioned.
Assemble RUBBER WASHER (3),
RETAINER (4) and LOCKNUT (5) onto
threads of SPOUT SHANK (1, 1a) from
underside of SINK.
GOOSE NECK
SPOUT (POP-UP)
2
1
SINK
Align SPOUT and tighten LOCKNUT (5).
Be sure slot in BRASS WASHER (4) is
positioned to the rear as shown.
GOOSE NECK
SPOUT
1a
2a
SINK
3
SLOT
4
3
5
4
SLOT
5
2
VALVE ASSEMBLY WITH RIGID VALVE CONNECTIONS
Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks.
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and
attach to SPOUT SHANK (7) and tighten.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto
valves until snug against internal stop.
10
11
10
11
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten
COUPLING NUT (14) firmly.
3
MOUNTING
LEDGE
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
11
5/16'' MIN.
5
10
5
2
1
13
14
HOT
3
2
1
7
14
MOUNTING SURFACE
4
8
6
13
9
COLD
5
2a
VALVE ASSEMBLY WITH FLEXIBLE HOSE VALVE CONNECTIONS
Press TEE (8) onto SPOUT SHANK (5) making certain that the O-RING (9)
is properly seated on SPOUT SHANK (5). Push COUPLING (4) into TEE (8)
and attach to SPOUT SHANK (5) and tighten.
Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).
Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE
SUPPLIES (2) (not included. Use adjustable wrench to tighten connections.
Do not over tighten.
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK.
5
9
8
6A
7A
1A
COUPLING
NUT
1
1/2" PIPE
THREAD
2
HOT
3
7
6
FLEXIBLE
SUPPLIES
3
4
3/8 O.D.
BULL-NOSE
RISERS
COLD
COMPRESSION
NUT
FERRULE
3/8 COMPRESSION
CONNECTION
DRAIN ASSEMBLY (6542.140/.170)
Apply a bead of PUTTY around underside of DRAIN FLANGE (1) flange.
Insert DRAIN PLUG (2) into SINK drain hole.
Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4),
and LOCKNUT (5) from underneath sink.
Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG.
Connect other end to trap.
1
PUTTY
SINK
2
3
4
5
2
60186 REV.1.8 (2/16)
4
INSTALL HANDLES
7
6
2
Turn VALVES (1) to off position.
Insert ADAPTOR (8) with larger diameter over the VALVE STEM (4).
Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4).
7
5
3
8
4
1
Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into
hot valve (left side).
Insert HANDLE SCREW (7) into HANDLES and tighten with screwdriver.
5
TEST INSTALLED FAUCET
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and TEE connections for leaks.
Turn handles into OFF position and replace AERATOR.
6
AERATOR
SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW, and INDEX.
STOP
WASHER
90°
SPRING
CLIP
AERATOR may accumulate dirt causing distorted and reduced water flow.
Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow.
To clean, first turn off hot and cold water supplies, then:
CARTRIDGE
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at base of CARTRIDGE.
Replace CARTRIDGE until flange is tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW and INDEX.
SCREEN
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
60186 REV.1.8 (2/16)
SPREAD LAVATORY
FAUCETS
MODEL NUMBERS
M970041-0020A
SPOUT
6500 6530
6502 6532
066074-0070A
VR AERATOR, 0.5gpm
M922858-0020A
VR AERATOR, 0.35gpm
Appropriate finish code
CHROME
912711-0070A
O-RING
002
A911748-0020A
SPOUT GASKET
000690-0020A
HANDLE SCREW
051211-0070A
INDEX KIT (PAIR)
015025-YYY0A
DRAIN COMPLETE
030256-0070A
SPOUT
MOUNTING KIT
051210-0020A
LEVER HANDLE
070532-0040A
TAILPIECE
M970039-0020A
SPOUT
M918014-0070A
ADAPTER
051217-0020A
WRIST BLADE
HANDLE
051322-0020A
VANDAL PROOF SCREW
000690-0020A
HANDLE SCREW
M964481-0070A
AERATOR 1.2 GPM
066508-0020A
AERATOR 0.5VR GPM
051211-0070A
INDEX KIT
M922286-0020A
AERATOR 0.35 GPM
M918014-0070A
ADAPTER
904939-0020A
BONNET NUT
912711-0070A
O-RING
028757-0070A
SPOUT GASKET
951764-0070A
CARTRIDGE
FOR PRODUCTS SOLD BEFORE 1/1/16
066497-0020A
COMPLETE
DRAIN BODY
030256-0070A
SPOUT MOUNTING KIT
066116-YYY0A
DRAIN STOPPER
051212-0020A
ESCUTCHEON KIT
028617-0020A
POP-UP ROD
012112-0070A
TUBE SEAL &
COUPLING KIT
051213-0070A
VALVEMOUNTING
KIT
066117-YYY0A
FLANGE KIT
033757-0070A
TEE MOUNTING KIT
070847-0070A
CLIP
033757-0070A
TEE MOUNTING KIT
066118-0070A
PIVOT ROD
024220-0070A
COUPLING NUT
012111-0070A
TUBE & TEE KIT (8" CENTERS)
900864-0070A
DRAIN BODY
066064-0070A
TUBE & TEE KIT (12" CENTERS)
TAILPIECE INSERT
M970033-0070A
FLEXIBLE HOSE &
TEE KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
070532-0070A
TAILPIECE
072574-0070A
EXTENSION ROD
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2016
60186 REV.1.8 (2/16)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement