advertisement
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 1
®
ALPHA WASH 700
C61350
INSTRUCTION MANUAL
Page
21
21
7
14
22
4
5
2
3
INDEX
Contents
Safety information
Unpacking and preparation
Installation and start-up
Control panel
Menu setting
Maintenance
Technical information
Cause and solution of problems
Channel functions
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.
Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.
1
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 2
ALPHA WASH 700
700W
3
IP20
Pb
SAFETY INFORMATION
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 3 metres
(9’ 10”) from the lens of the projector.
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (
Class I
appliance according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to connect to the electricity line, in order to avoid overloading.
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 150°C (302°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the likelihood of the lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another
20 minutes to avoid getting burnt.
The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be mounted and, if visibly damaged, they have to be replaced with genuine spares.
• Lamp
The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the apparatus.
- Carefully read the "operating instructions" provided by the lamp manufacturer.
- Immediately replace the lamp if damaged or deformed by heat.
• Battery
This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. Instructions on how to remove the battery from the product are available on
www.claypaky.it
The products referred to in this manual conform to the European Community Directives to which they are subject:
•
Low Voltage 2006/95/CE
•
Electromagnetic Compatibility 2004/108/CE
2
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 3
UNPACKING AND PREPARATION
1
099100
2 x 183102/802
Lamp 700W
(fitted into projector)
Packing contents
- Fig. 1
2
LOCKED
UNLOCKED
3
45° 45°
90°
90
°
°
90
90°
PAN Mechanism Lock and Release (every 90°)
- Fig. 2
TILT Mechanism Lock and Release (every 45°)
- Fig. 3
ALPHA WASH 700
3
LOCKED
UNLOCKED
5° 5°
4 4
° °
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 4
INSTALLATION AND START-UP
4
Installing the projector
- Fig. 4
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
5
2
1
2
1
3
Connecting and disconnecting power cable
- Fig. 5
ALPHA WASH 700
4
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 5
CONTROL PANEL
6
Mains
L
N
Connecting to the mains supply
- Fig. 6
7
DMX 512
5 PIN
5
4
3
1
2
SCREEN
SIGNAL
SIGNAL
DMX 512
5
DMX 512
3 PIN
2
3
1
SCREEN
Connecting to the control signal line (DMX)
- Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT:
The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
8
Fixture ID
2
Dmx Address
1
Warning Message
SIGNAL
SIGNAL
Switching on the projector
- Fig. 8
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model Firmware xxx (Fixture ID) System errors
Alpha WASH Version X.X.X Dmx Address xxx E: .........................
700 Date - Hour W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel
(Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
F key will be cancelled.
Continue
➔
5
ALPHA WASH 700
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 6
9
28
28
Reversal of the display
- Fig. 9
To activate this function, press UP
B and DOWN
C keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
Functions of the buttons - Using the menu
F
C
DOWN
B
UP
D
LEFT
E
RIGHT
Confirms the displayed value, or activates the displayed function, or enters the successive menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
USING THE MENU:
1) Press
F once – “Main Menu” appears on the display.
2) Use the UP
B and DOWN
C keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.13
3) Press
F to display the first item in the selected menu.
4) Use the UP
B and DOWN
C keys to select the MENU items.
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
F to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds.
ALPHA WASH 700
6
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 7
1
4
Option
Information
Manual
Control
Test
Advanced
Set Up
Dmx
Address
Channel
Mode
Fixture ID
Ethernet
Interface
Manual
Control
Lamp
Reset
Channel
ALPHA WASH 700
MENU SETTING
MAIN MENU
2
Option Lamp Dmx
Pan / Tilt
Color
Shutter
Power Mode
Shutter
On Error
Dimmer On
Shutter
4-700W
Full fan speed
400W
Low fan speed
4-700W
Auto fan speed
Invert
Pan
Invert
Tilt
Swap
Pan-Tilt
Encoder
Pan-Tilt
Color
Mixing
Color mixing curve
Fixed Wheel
Shortcut
Display
Setting
Default
Preset
User
Preset 1
User
Preset 2
User
Preset 3
3
Information
5
Test Pan / Tilt
Colour
Beam
All
7
System
Version
Board
Diagnost.
Dmx
Monitor
Fans
Monitor
Network params
System
Errors
Fixture
Hours
Lamp
Hours
Lamp
Strikes
6
Advanced
Access code
1234
Upload
Firmware
Setup
Model
Calibration
Continue
➔
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 8
NOTE: On grey the default options
Set Up
Dmx
Address
Address xxx
ALPHA WASH 700
Channel
Mode
Standard
Vector
Fixture ID Value xxx
Ethernet
Interface
Control
Protocol
Repeat on
DMX
Universe
8
SET UP MENU
DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS.
1) Press
F
- the current DMX Adress appear on the display.
2) Use the UP
B and DOWN
C
, RIGHT
E keys to plan the DMX
Address.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
CHANNEL MODE
Allows you to select a channel arrangement from the two available.
1) Press
F
- the current settings appear on the display (Standard or
Vector).
2) Use the UP
B and DOWN
C keys to select one of the following settings:
- Standard
- Vector
3) Press
F to confirm the selection or LEFT
D to keep current settings.
FIXTURE ID
Allows you to select the FIXTURE ID.
1) Press
F
- the current Fixture ID appear on the display.
2) Use the UP
B
, DOWN
C
, RIGHT
E keys to plan the Fixture ID.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
F
.
2) Use the UP
B and DOWN
C keys to select the “Ethernet Interface” options to set:
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the control unit used:
1) Press
F the current setting appears on the display.
2) Use the UP
B and DOWN
C keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
F to confirm the selection or LEFT
D to keep the current setting.
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal to all the connected projectors.
1) Press
F the current setting appears on the display.
2) Use the UP
B and DOWN
C keys to select one of the following settings:
-
Disabled:
DMX transmission disabled.
-
Enabled on primary:
DMX transmission enabled.
3) Press
F to confirm the selection or LEFT
D to keep the current setting.
Universe
It lets you assign the “Universe” number to be assigned to a series of projectors.
1) Press
F
– the current Universe address appears on the display.
2) Use the UP
B
, DOWN
C
, RIGHT
E keys to set the Universe address.
3) Press
F to confirm the selection or LEFT
D to keep the current setting.
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 9
Option Lamp Dmx
On
Off
Pan / Tilt
Invert
Pan
On
Off
ALPHA WASH 700
Invert
Tilt
On
Off
Swap
Pan-Tilt
On
Off
Encoder
Pan-Tilt
On
Off
Color
Color
Mixing
Rgb
Cmy
Color
Mixing curve
Curve 1
Curve 2
Fixwheel
Shortcut
On
Off
OPTIONS MENU
LAMP DMX
Used for enabling lamp remote control channel.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off) the lamp remote control channel.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
PAN / TILT
Invert pan
Used for reversing Pan movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off)
PAN inversion.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
Invert tilt
Used for reversing tilt movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
Tilt inversion.
B and DOWN
C keys to enable (On) or disable (Off)
3) Press
F to confirm the selection or LEFT
D to keep current settings.
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
COLOR
Color mixing
Used for reversing the CMY color mixing system.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys select one of the following settings:
RGB color mixing mode
CMY color mixing mode
3) Press
F to confirm the selection or LEFT
D to keep current settings.
Color mixing curve
It lets you select the “Color mixing curve” from the two available.
1) Press
F the current setting appears on the display.
2) Use the UP
B and DOWN
C keys to select one of the following settings:
Curve 1
Curve 2
3) Press
F to confirm the selection or LEFT
D to keep the current setting.
9
Fixed wheel short-cut
Used for optimizing color change time so that the disc turns in the direction that requires shorter movement.
1) Press
F
– the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off) color change optimization.
3) Press
F to confirm the selection, or LEFT
D to keep current settings.
Continue
➔
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 10
Shutter
Shutter
On Error
On
Off
Dimmer On
Shutter
On
Off
Power Mode
4-700W
Full fan speed
400W
Low fan speed
4-700W
Auto fan speed
Display
On
Off
ALPHA WASH 700
Setting
Default
Preset
User
Preset 1
User
Preset 2
User
Preset 3
Load
Preset 2
Save To
Preset 2
Load
Preset 3
Save To
Preset 3
Reset To
Dafault
Go Back
Load
Preset 1
Save To
Preset 1
SHUTTER
Shutter on error
Used for automatically closing the stop/strobe in the event of Pan/Tilt position error.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off) automatic stop/strobe closing in the event of Pan/Tilt position error.
3) Press
F to confirm the selection, or LEFT
D to keep current settings.
Dimmer on Shutter
Enables automatic closing of the dimmer when the strobe is completely closed.
1) Press
F
– the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off) the automatic closing of the dimmer.
3) Press settings.
F to confirm the selection, or LEFT
D to keep current
POWER MODE
Allows you to select a Power Mode from the three available.
1) Press
F
- the current settings appear on the display.
2) Use the UP
B and DOWN
C keys to select one of the following settings:
-
4-700W Full fan speed
: Lamp can change from full-power (700W) to half-power (400W) using the LAMP CONTROL channel. Fans always work at Full speed.
-
400W Low fan speed
: Lamp constantly works in half-power mode
(400W) while the Fan always works at Low speed. With LAMP
CONTROL channel you can only switch the lamp ON and OFF.
-
4-700W Auto fan speed
: Lamp can change from full-power (700W) to half-power (400W) using the LAMP CONTROL channel. Automatically the fans switch from Full speed to Low speed respectively.
3) Press
F to confirm the selection or LEFT
D to keep current setting.
DISPLAY
Used for automatically reduce brightness on the display after about 30 seconds in idle.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to enable (On) or disable (Off) the decreasing of display brightness.
3) Press
F to confirm the selection or LEFT
D to keep current settings.
SETTING
Used to save 3 different settings of the items in the options menu and relative submenus.
1) Press
F
- “Default preset” appears on the display.
2) Use the UP
B and DOWN
C keys to select one of the following configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
3) Press
F
- “Load preset X” appears on the display.
4) Use the UP
B and DOWN
C keys to select:
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting and return to the next higher level.
10
(*) DEFAULT PRESET
Used for restoring default values on all options menu items and relevant submenus.
1) Press
F
, a confirmation message (Are you sure?) appears on the display.
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 11
2) Select YES to confirm the selction or NO to keep current setting.
OPTION
Lamp DMX
Invert Pan
DEFAULT
On
Off
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
Color mixing
Color mixing curve
Fixed Wheel Shortcut
Shutter on error
Dimmer on Shutter
Power Mode
Display
Off
Off
On
CMY
Curve 1
On
Off
Off
4-700 Full fan speed
On
Information
ALPHA WASH 700
System
Errors
Fixture
Hours
Lamp
Hours
Lamp
Strikes
Total XXX
Partial XXX
Reset...
INFORMATION MENU
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since the fixtures switching-on.
1) Pressing
F you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?) appears on the display.
2) Select YES to reset the list or NO to go back.
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
F
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the last reset to date.
2) Press
F to reset partial projector working hours a confirmation message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the current setting and return to the top menu level.
Total XXX
Partial XXX
Reset...
LAMP HOURS
Used for displaying the lamp working hours (total and partial).
1) Press
F
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working hours with the lamp on (from manufacture to date).
Partial counter
Counts the number of lamp working hours since the last reset to date.
2) Press
F to reset partial lamp working hours, a confirmation message
(Are you sure ?) appears on the display.
3) Select YES to reset partial counter or NO to keep the current setting and return to the top menu level
Total XXX
Partial XXX
Reset...
11
LAMP STRIKES
Used for displaying the number of times the lamp was turned on (total and partial).
1) Press
F
- the number of times the lamp was turned on (total and partial) appears on the display.
Total counter
Counts the number of times the lamp was turned on (from manufacture to date).
Partial counter
Counts the number of times the lamp was turned on since the last reset to date.
Continue
➔
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 12
ALPHA WASH 700
System
Version
Board Revis. Hw.rv.
CPU brd x.x.x x.x
com.dev x.x
0: PT-3f x.x x.x
1: 6-Ch x.x x.x
2: 8-Ch x.x x.x
Board
Diagnost.
Board Status Err%
0:PT-3f Good 0.00
1:6-Ch Good 0.00
2:8-Ch Good 0.00
Dmx
Monitor
Fans
Monitor
Fan Speed (RPM)
Ball.In. XXXX
Eff.In XXXX
Lamp XXXX
Network params
Manual
Control
Lamp
On
Off
Reset
No
Yes
Channel
2) Press
F to reset partial lamp strikes hours, a confirmation message
(Are you sure ?) appears on the display.
3) Select YES to reset partial counter or NO to keep the current setting and return to the top menu level
SYSTEM VERSION
Used for displaying the software and hardware version of each board installed in the projector.
CPU brd (CPU board)
0: PT-3f (Pan / Tilt board)
1: 6-Ch (6 channel board)
2: 8-Ch (8 channel board)
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Pan / Tilt board)
1: 6-Ch (6 channel board)
2: 8-Ch (8 channel board)
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in percentage (Perc).
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
Ball. IN (Ballast IN Fan)
Eff.IN (Effects IN Fan)
Lamp (Lamp Fan)
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address:
Internet Protocol address (two projectors must not have the same IP address)
IP mask: 255.0.0.0
Mac address:
Media Access Control: the projector’s Ethernet Address
12
MANUAL CONTROL
LAMP
Used for turning lamp on and off from the projector control panel.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B and DOWN
C keys to turn the lamp on (On) or off (Off)
3) Press
F to confirm the selection or LEFT and return to the top level.
D to keep current settings
RESET
Used for resetting the projector.
1) Press
F to reset the projectors, a confirmation message (Are you sure
?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level.
CHANNEL
Used for setting channel levels from the projector control panel.
1) Press
F
- the first channel appears on the display.
2) Use the UP
3) Press
B and DOWN
C keys to select the required channel:
F and use the UP
B and DOWN
C keys to select the required DMX level (value between 0 and 255).
4) Press LEFT
D to return to the top menu level.
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 13
Test
Pan-Tilt
Colour
Beam
All
TEST MENU
TEST
Allows you to check the proper functioning of effects.
1) Press
F to return to the top menu level.
2) Use the UP
3) Press
B and DOWN
C keys to select the required test.
F to confirm the selection or LEFT
D to keep current settings.
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colour effects (CMY / CTO / Colour wheel)
Beam effects (Stopper-Strobe / Dimmer / Beam shaper / Zoom)
All effects
Advanced
Code
1234
Upload
Firmware
Transfer the firmware on all the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model may damage the fixture.
Are you sure ?
Yes/No
Calibration
ADVANCED MENU
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP
B
, DOWN
C
, RIGHT
E keys.
Press
F
- "Menu advanced" appears on the display
UP LOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
F
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level
SETUP MODEL
Allows you to change the default model of projector.
1) Press
F a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current setting and return to the top menu level.
CALIBRATION
Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.
1) Press
F
- “channels” appears on the display.
2) Using the UP regulate.
3) Press
B and DOWN
C keys, select the effect you wish to
F and use the RIGHT
E
, UP
B and DOWN
C buttons to make the adjustment by setting a value between 0 and 255.
4) Press
F to confirm the selection or LEFT
D to keep current settings and return to the top level.
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
F
– a confirmation message appears on the display (Reset calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the current setting and return to the top menu level.
ALPHA WASH 700
13
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 14
10
1
1/4 Turn
MAINTENANCE
2
11
1
3
4
Locking and releasing Pan and Tilt movements
- Refer to the instructions in the UNPACKING AND PREPARATION section.
Opening the head covers
- Fig. 10.
Closing the head covers
- Fig. 11.
2
1/4 Turn
ALPHA WASH 700
14
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 15
12 13
1
A
Upper Side
1
2
Opening and closing lamp compartment
- Fig. 12
14
OK NO NO
Lamp regulation
- Fig. 14
To centre the lamp, turn the three adjusting screws as shown in the figure.
ALPHA WASH 700
15
2
A
Lower Side
3
A
Lamp change
- Fig 13
Take the new lamp out of its package and insert in the fitting.
WARNING: do not touch the lamp’s envelope with bare hands.
Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.
Upper Side
Lower Side
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 16
15
Upper Side
Parts requiring frequent cleaning.
Periodical cleaning
- Fig. 15
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
•
General cleaning of internal parts.
•
Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.
•
General visual check of the internal components, cabling, mechanical parts, etc.
•
Electrical, photometric and functional checks; eventual repairs.
ALPHA WASH 700
16
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 17
16
Lower Side
1
Thermostat
2
Upper Side
3
Extraction of the effect modules: Preliminary operations
- Fig. 16
4
ALPHA WASH 700
17
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 18
17
Upper Side
1
Upper Side
2
Extraction of the effect modules
- Fig. 17
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules:
Repeat the operations indicated in Fig. 16 - 17 - 18 and 19 in reverse order.
ALPHA WASH 700
18
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 19
18
Lower Side
3
4
Upper Side
Upper Side
5
Extraction of the effect modules
- Fig. 18
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules:
Repeat the operations indicated in Fig. 16 - 17 - 18 and 19 in reverse order.
ALPHA WASH 700
19
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 20
19
Lower Side
6
7
Upper Side
Upper Side
8
Extraction of the effect modules
- Fig. 19
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules:
Repeat the operations indicated in Fig. 16 - 17 - 18 and 19 in reverse order.
ALPHA WASH 700
20
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 21
575
(22.64")
385
(15,16")
410
(16,14")
375
(14.76")
50
(1,97")
220
(8,66")
220
(8,66")
390
(15,35")
405
(15.94")
505
(19,88")
Power supplies available
100-120V 50/60Hz
200-240V 50/60Hz
Input power
• 1050VA a 230V 50Hz.
Lamp
Discharge lamp.
• Type MSR GOLD 700/2
- Cap PGJX28
- Colour temperature 7200 K
- Luminous flux 50000 lm
- Average life 750 h
- Any working position
Motors
17 stepper motors, operating with microsteps, totally microprocessor controlled.
Optical unit
• Elliptic reflector with high luminous efficiency
Channels
Max 21 control channels.
Inputs
• DMX 512
Movable body
• Movement by means of two stepper motors, controlled by microprocessor.
• Automatic repositioning of PAN and TILT after accidental movement not controlled by control unit.
• Travel:
- PAN = 540°
- TILT = 250°
• Maximum speeds:
- PAN = 3.20 (Normal) / 2.90 (Fast)
- TILT = 1.89 (normal) / 1.75 (Fast)
• Resolution:
- PAN = 2.11°
- PAN FINE = 0.008°
- TILT = 0.98°
- TILT FINE = 0.004°
TECHNICAL INFORMATION
IP20 protection rating
• Protected against the entry of solid bodies larger than 12mm (0.47”).
• No protection against the entry of liquids.
CE Marking
In conformity with the European Union Low Voltage
Directive 2006/95/CE and Electromagnetic compatibility Directive 2004/108/CE.
Safety Devices
• Bipolar circuit breaker with thermal protection.
• Automatic break in power supply in case of overheating or failed operation of cooling system.
Cooling
Forced ventilation with axial fans.
Body
• Aluminium structure with die-cast plastic cover.
• Two side handles for transportation.
• Device locking PAN and TILT mechanisms for transportation and maintenance.
Working position
Functioning in any position.
Weight
• about 20.60 Kg (45lbs 5ozs).
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON
ELECTRONICS NON-OPERATIONAL
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES
No mains supply.
Lamp exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
CHECKS AND REMEDIES
Check the power supply voltage.
Replace the lamp. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
PROBLEMS
ALPHA WASH 700
21
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 22
CHANNEL FUNCTION
ALPHA WASH 700
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
STANDARD
CYAN
MAGENTA
YELLOW
CTO
COLOUR WHEEL
STOP / STROBE
DIMMER
DIMMER FINE
BEAM SHAPER INSERTION
BEAM SHAPER ROTATION
ZOOM
PAN
PAN FINE
TILT
TILT FINE
FUNCTION
RESET
LAMP CONTROL (with Option "Lamp Dmx" ON)
19
20
21
CHANNEL MODE
VECTOR
CYAN
MAGENTA
YELLOW
CTO
COLOUR WHEEL
STOP / STROBE
DIMMER
DIMMER FINE
BEAM SHAPER INSERTION
BEAM SHAPER ROTATION
ZOOM
PAN
PAN FINE
TILT
TILT FINE
FUNCTION
RESET
LAMP CONTROL (with Option "Lamp Dmx" ON)
PAN - TILT TIME
COLOUR TIME
BEAM TIME
ALPHA WASH 700
22
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 23
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.
• STOP / STROBE - channel 6 • COLOUR MIXING - channel 1 - 2 - 3
Operation with option color mixing: RGB
CHANNEL 1 CHANNEL 2 CHANNEL 3
BIT
255
%
100
EFFECT
COLOUR EXCLUDED
BIT % EFFECT
252 - 255
98.7 - 100
OPEN
239 - 251 93.7 - 98.2
RANDOM FAST STROBE
226 - 238
88.7 - 93.2
RANDOM MEDIUM STROBE
213 - 225 83.7 - 88.2
RANDOM SLOW STROBE
208 - 212 81.7 - 83.2
OPEN
207 81.2
FAST PULSATION
108 42.5
SLOW PULSATION
104 - 107 41.0 - 42.0
OPEN
103 40.5
FAST STROBE (12 flash/sec)
0
0.0
COLOUR INSERTED
CYAN MAGENTA YELLOW
IMPORTANT:
The lamp dim to half power 1 second after all the 3 channels stay at 0% level. The lamp goes back to full power when the channels level is put higher than 0%.
Operation with option color mixing: CMY
CHANNEL 1 CHANNEL 2 CHANNEL 3
BIT
255
%
100
EFFECT
COLOUR INSERTED
4
0 - 3
1.7
0.0 - 1.2
SLOW STROBE (1 flash/sec)
CLOSED
IMPORTANT:
The lamp dim to half power 1 second after the channel stay at
0% level. The lamp goes back to full power when the channel level is put higher than 0%.
• DIMMER - channel 7
BIT
255
%
100
EFFECT
MAGENTA YELLOW
0 0.0
COLOUR EXCLUDED
CYAN
IMPORTANT:
The lamp dim to half power 1 second after all the 3 channels stay at 100% level. The lamp goes back to full power when the channels level is put lower than 100%.
• C.T.O. - channel 4
CHANNEL 4
BIT
255
%
100
EFFECT
FILTER INSERTED
0 0.0
The lamp is linearly dimmed from full power to half power electronicaly and mechanically from half power to off.
• DIMMER FINE - channel 8
BIT
255
%
100
EFFECT
CTO
• COLOUR WHEEL - channel 5
0 0.0
FILTER EXCLUDED
BIT
255
%
100
EFFECT
FAST ROTATION (160 rpm)
0 0.0
• BEAM SHAPER INSERTION - channel 9
BIT
170-255
%
EFFECT
66.7-100 SHAPER 2
ALPHA WASH 700
37
30
22
15
8
0
75
67
60
52
45
128
127
120
112
105
97
90
82
50.0
49.7
47.0
44.0
41.2
38.0
35.0
32.0
29.5
26.2
23.7
20.5
17.5
14.2
11.7
8.7
6.0
3.2
0.0
SLO W ROTATION (0.2 rpm)
BLUE + WHITE
BLUE
ORANGE + BLUE
ORANGE
AQUAMARINE + ORANGE
AQUAMARINE
LAVENDER + AQUAMARINE
LAVENDER
LIGHT GREEN + LAVENDER
LIGHT GREEN
GREEN + LIGHT GREEN
GREEN
CTB + GREEN
CTB
RED + CTB
RED
WHITE + RED
WHITE
23
85-169 33.2-66.2
SHAPER 1
0 - 84 0.0 - 33.0
WHITE
Continue
➔
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 24
• BEAM SHAPER ROTATION - channel 10
STOP
540°
360°
0°
BIT
255
%
100
EFFECT
FAST ROTATION (120 rpm)
193 75.5
191 - 192 74.7 - 75.0
190 74.2
SLOW ROTATION (3 rph)
STOP
SLOW ROTATION (3 rph)
128
127
105
84
63
42
21
0
50.0
49.7
41.7
33.0
24.7
16.2
8.2
0.0
FAST ROTATION (120 rpm)
POSITION 540 °
POSITION 450
°
POSITION 360
°
POSITION 270
°
POSITION 180
°
POSITION 90 °
POSITION 0 °
• ZOOM - channel 11
BIT
255
%
100
EFFECT
WIDE BEAM
• PAN FINE - channel 13
Operation with option InvertPan
G
Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
Off)
BIT
255
%
100
0 0.0
Operation with option InvertPan
G
On
(Tilt conventionally represented at 14% and option Invert Tilt
G
Off)
BIT
255
%
100
• PAN - channel 12
Operation with option InvertPan
G
Off
0 0.0
NARROW BEAM
(Tilt conventionally represented at 14% and option Invert Tilt
BIT
255
%
100
G
Off)
0 0.0
• TILT - channel 14
Operation with option Invert Tilt
G
Off
(Pan conventionally represented at 0% and option Invert Pan
G
Off)
BIT
255
%
100
128 50.0
0 0.0
Operation with option InvertPan
G
On
(Tilt conventionally represented at 14% and option Invert Tilt
G
Off)
BIT
255
%
100
ALPHA WASH 700
0 0.0
24
0 0.0
Operation with option Invert Tilt
G
On
(Pan conventionally represented at 0% and option Invert Pan
G
Off)
BIT
255
%
100
128 50.0
0 0.0
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 25
• TILT FINE - channel 15
Operation with option Invert Tilt
G
Off
(Pan conventionally represented at 0% and option Invert Pan
BIT
255
%
100
G
Off)
0 0.0
Operation with option Invert Tilt
G
On
(Pan conventionally represented at 0% and option Invert Pan
G
Off)
BIT
255
%
100
• LAMP CONTROL (only with option LAMP DMX On) - channel: 18
IMPORTANT:
Alpha Wash 700 is not provided with hot restrike igniter
ON
ON
ON
ON
OFF
OFF
BIT
255
180
179
101
100
26
25
0
%
100
70.5
70.0
39.5
39.0
10.0
9.7
0.0
EFFECT
LAMP ON (FULL POWER)
Lamp ignition after 5 s in full power levels.
Immediate transition from half to full power.
LAMP ON (FULL POWER)
LAMP ON (HALF POWER)
Immediate transition from full to half power.
Lamp ignition not allowed in half power.
LAMP ON (HALF POWER)
LAMP OFF
Lamp switch off passing throug the unused range and staying 5 s in
Lamp OFF levels.
LAMP OFF
UNUSED RANGE
0 0.0
• FUNCTION - channel: 16
BIT
255
%
100
UNUSED RANGE
EFFECT
52 20.5
51 20.0
LINEAR (DEFAULT)
39 15.0
26 10.0
CONVENTIONAL
NORMAL SPEED
FAST SPEED (DEFAULT) 13 5.0
0-12 0.0-4.7
UNUSED RANGE
DIMMER CURVE
FUNCTION
PAN-TILT
FUNCTION
The functions are actived passing through the "unused range" and staying 5 seconds in necessary level
• RESET - channel: 17
BIT
255
%
100
EFFECT
COMPLETE RESET
Complete reset is activated passing throug the unused range and staying
5 seconds in complete reset levels.
128
127
50.0
49.7
COMPLETE RESET
PAN / TILT RESET
Pan / Tilt reset is activated passing throug the unused range and staying
5 seconds in Pan / Tilt reset levels.
77 30.0
76 29.7
26 10.0
25 9.7
0 0.0
PAN / TILT RESET
EFFECTS RESET
Effects reset is activated passing throug the unused range and staying
5 seconds in Effects reset levels.
EFFECTS RESET
UNUSED RANGE
ALPHA WASH 700
25
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 26
TIMING CHANNELS
Timing Channel Channel function
19 Pan - Tilt time Pan - Tilt - (Pan fine - Tilt fine)
20 Colour time CMY - CTO - Colour wheel
21 Beam time Dimmer - Zoom
TIME TABLE
58
59
60
61 14
62
63
64
65
66 16
67
68
69
70
71 18
72
73
74
75
76 20
77
78
79 21
80
81
82
83
84 23
85
BIT Seconds
43 8.6
44 8.8
45 9
46 9.2
47 9.4
48 9.6
49 9.8
50 10
51 10.2
52 10.4
53 10.6
54
55
56
57
25 5
26 5.2
27 5.4
28 5.6
29 5.8
30 6
31 6.2
32 6.4
33 6.6
34 6.8
35 7
36 7.2
37 7.4
38 7.6
39 7.8
40 8
41 8.2
42 8.4
BIT Seconds
0 Full
1 0.2
2 0.4
3 0.6
4 0.8
5 1
6 1.2
7 1.4
8 1.6
9 1.8
10 2
11 2.2
12 2.4
13 2.6
14 2.8
15 3
16 3.2
17 3.4
18 3.6
19 3.8
20 4
21 4.2
22 4.4
23 4.6
24 4.8
102 30
103
104
105
106
107 32
108
109
110
111
112 34
113
114
115
116
117 36
118
119
120
121
122 38
123
124
125 39
126
127
128
BIT Seconds
86
87
88
89 25
90
91
92
93
94 27
95
96
97
98
99 29
100
101
BIT Seconds
172
173 58
174
175
176 59
177
178
179
180
181 65
182
183
184
185
186 75
187
188
189
190
191 85
192
193
194
195
196 95
197
198
200
201 110
202
203
204 120
205
206
208
209 140
210
211
213
214 160
215
145 47
146
147
148
149
150 49
151
152
153 50
154
155
156
157
158 52
159
160
161
162
BIT Seconds
129
130 41
131
132
133
134
135 43
136
137
138
139
140 45
141
142
143
144
163 54
164
165
166
167
168 56
169
170
171
BIT Seconds
216
217
218
219 180
220
221
222
223
224 200
225
226
227 210
228
229
230
231
232 230
233
234
235
236
237 250
238
239
240
241
242 270
243
244
245
246
247 290
248
249
250
251
252
253
254
Follow cue
Data
ALPHA WASH 700
26
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 27
099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 28
CLAY PAKY
S.p.A.
- Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311- Fax +39-035-301876 -
www.claypaky.it
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project