Iiyama ProLite B2209HDS-1 User Guide Manual Pdf

Iiyama ProLite B2209HDS-1 User Guide Manual Pdf
USER MANUAL
ENGLISH
Thank you very much for choosing the
iiyama LCD monitor.
We recommend that you take a few
minutes to read carefully through this
brief but comprehensive manual before
installing and switching on the monitor.
Please keep this manual in a safe
place for your future reference.
Downloaded from ManualMonitor.com Manuals
ENGLISH
Downloaded from ManualMonitor.com Manuals
Congratulations!
The display you have just purchased carries the TCO’03 Displays
label. This means that your display is designed, manufactured
and tested according to some of the strictest quality and
performance product, designed with the user in focus that also
minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
• Good visual ergonomics and image quality in order to improve the working environment for the user
and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution,
reflectance, colour rendition and image stability.
Energy
• Energy-saving mode after a certain time – beneficial both for the user and the environment
• Electrical safety
Emissions
• Electromagnetic fields
• Noise emissions
Ecology
• The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 001
• Restrictions on
o chlorinated and brominated flame retardants and polymers
o heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in cooperation
with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s
TCO has been involved in influencing the development of IT equipment in a more user-friendly
direction. Our labelling system started with displays in 1992 and is now requested by users and ITmanufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
Downloaded from ManualMonitor.com Manuals
ENGLISH
environmental requirements in the world. This makes for a high
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 2004/108/EC “EMC
Directive” , 2006/95/EC “Low Voltage Directive” and 2009/125/EC “ErP Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in
residential areas, business and light industrial premises and small-scale enterprises, inside as
well as outside of the buildings. All places of operation are characterised by their connection to
the public low voltage power supply system.
ENGLISH
IIYAMA CORPORATION: Breguetlaan 8, 1438BC Oude Meer The Netherlands
A certified power supply cord has to be used with this equipment. The relevant national installation
and/or equipment regulations shall be considered. A certified power supply cord not lighter than
ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2
or H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible cord be of synthetic rubber
according to IEC 60245 (designation H05RR-F 3G 0.75mm2) shall be used.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the address:
http://www.iiyama.com
You can access the Web page of different countries from there.
We reserve the right to change specifications without notice.
All trademarks used in this user manual are the property of their respective owners.
Downloaded from ManualMonitor.com Manuals
TABLE OF CONTENTS
FOR YOUR SAFETY.............................................................................................. 1
SAFETY PRECAUTIONS ................................................................................ 1
SPECIAL NOTES ON LCD MONITORS.......................................................... 3
CLEANING....................................................................................................... 3
BEFORE YOU OPERATE THE MONITOR ............................................................ 4
FEATURES ...................................................................................................... 4
CHECKING THE CONTENTS OF THE PACKAGE ......................................... 4
FITTING AND REMOVAL OF BASE : ProLite B2209HDS .............................. 5
FITTING AND REMOVAL OF BASE : ProLite E2209HDS .............................. 6
CONTROLS AND CONNECTORS : ProLite B2209HDS ................................. 7
CONTROLS AND CONNECTORS : ProLite E2209HDS ................................. 8
CONNECTING YOUR MONITOR : ProLite B2209HDS .................................. 9
CONNECTING YOUR MONITOR : ProLite E2209HDS .................................. 10
COMPUTER SETTING .................................................................................... 11
ADJUSTING THE HIGHT AND THE VIEWING ANGLE : ProLite B2209HDS .. 12
ADJUSTING THE VIEWING ANGLE : ProLite E2209HDS ............................. 12
OPERATING THE MONITOR................................................................................. 13
ADJUSTMENT MENU CONTENTS ................................................................ 15
SCREEN ADJUSTMENTS............................................................................... 20
POWER MANAGEMENT FEATURE ............................................................... 23
TROUBLE SHOOTING .......................................................................................... 24
RECYCLING INFORMATION................................................................................. 25
APPENDIX ............................................................................................................ 26
SPECIFICATIONS : ProLite B2209HDS ......................................................... 26
SPECIFICATIONS : ProLite E2209HDS ......................................................... 27
DIMENSIONS : ProLite B2209HDS ................................................................ 28
DIMENSIONS : ProLite E2209HDS ................................................................ 28
COMPLIANT TIMING....................................................................................... 29
Downloaded from ManualMonitor.com Manuals
ENGLISH
CUSTOMER SERVICE .................................................................................... 3
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
ENGLISH
and contact your dealer or iiyama service center immediately. Further use may be dangerous and can
cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire
or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any
object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may
cause electric shock.
1
FOR YOUR SAFETY
Downloaded from ManualMonitor.com Manuals
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire.
To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also
cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable
is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is
recommended as looking at the screen continuously can cause eye strain.
FOR YOUR SAFETY
Downloaded from ManualMonitor.com Manuals
2
ENGLISH
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position
to the correct position.
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
ENGLISH
pattern you use.
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In this
case, the screen can be recovered slowly by changing the image or turning off the
Power Switch for some hours.
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
CUSTOMER SERVICE
NOTE
The fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama service
center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
CLEANING
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION
For safety reasons, turn off the power switch and unplug the monitor before you clean
it.
NOTE
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and the
LCD screen.
Thinner
Spray-type cleaner
Benzine
Wax
Abrasive cleaner
Acid or Alkaline solvent
Touching the cabinet with any product made from rubber or plastic for a long time may
cause degeneration or loss of paint on the cabinet.
CABINET
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
LCD
Periodic cleaning with a soft dry cloth is recommended.
SCREEN
Don't use tissue paper etc. because these will damage the LCD screen.
3
FOR YOUR SAFETY
Downloaded from ManualMonitor.com Manuals
BEFORE YOU OPERATE THE MONITOR
FEATURES
Supports Resolutions up to 1920 × 1080
High Contrast 1000:1 (Typical), ACR Function Available / Brightness 300cd/m2
(Typical), Quick Response Time 5ms (Typical)
Digital Character Smoothing
ENGLISH
Automatic Set-up
Stereo Speakers
2 × 2W Stereo Speakers
Plug & Play VESA DDC2B Compliant
Windows® 95/98/2000/Me/XP/Vista/7 Compliant
Power Management (VESA DPMS Compliant)
Ergonomic Design TCO ’03
VESA Mounting Standard (100mm×100mm) Compliant
Keyhole for Security Lock
CHEKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the monitor.
If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office.
Power Cable*1
D-Sub Signal Cable
Audio Cable
Stand*
Screw for stand fixing*
CAUTION
3
2
Safety Guide
DVI-D Signal Cable
Stand-Base
Quick Start Guide
*1 The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
2
* Accessory for ProLite E2209HDS.
*3 Accessory for ProLite B2209HDS.
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
4
FITTING AND REMOVAL OF BASE : ProLite B2209HDS
CAUTION
Put the monitor on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid electric shock or damage.
ENGLISH
<Installation>
A Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay
the monitor flat on a table with front face down.
B Install the Stand-Base to the Monitor.
C Fix the Monitor to the Stand by the screw firmly and then push-down knob.
Push-down knob
Screw for Stand-Base fixing
Stand-Base
<Removal>
A Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay
the monitor flat on a table with front face down.
B Pull the knob upwards, then remove the screw and the Stand-Base.
<Stopper pin>
Please stand the monitor and then remove the stopper
pin on the back of the stand slowly while pushing top
face of the stand before you install the monitor. Careful
attention is required as the monitor is sprung loaded
and may expand quickly when removing it.
Stopper pin
5
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
FITTING AND REMOVAL OF BASE : ProLite E2209HDS
CAUTION
Put the monitor on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid electric shock or damage.
<Installation>
Lay the monitor flat on a table with front face down.
ENGLISH
A Put a piece of soft cloth on the table beforehand to
prevent the monitor from being scratched.
Stand
B Insert stand into the monitor as shown in figure.
C Install the stand-base to the stand.
Stand
Stand-Base
<Removal>
Hooks
A Put a piece of soft cloth on the table beforehand to
prevent the monitor from being scratched.
Lay the monitor flat on a table with front face down.
B Press and hold the hooks inside, and pull the
Stand-Base.
C Insert thin stick into hole, push stick in whilst pulling
the stand away.
Thin Stick
Release hole
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
6
ENGLISH
CONTROLS AND CONNECTORS : ProLite B2209HDS
HDMI
<Front>
Power Switch (
DVI-D
D-SUB
AUDIO
<Back>
)
Power Indicator
NOTE Blue:
Normal operation
Orange: Power Management
The monitor enters into power management mode which reduces the power
consumption to less than 1W when receiving no horizontal and/or vertical
sync signal.
Menu / Select Button (MENU)
+ / Volune Button ( + )
- / ECO Mode Button ( - )
Auto Button (AUTO)
Speakers
AC Connector (AC IN)
Cable Holder
Keyhole for Security Lock
NOTE You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
Headphone Connector (AUDIO)
Audio Connector (AUDIO)
D-SUB mini 15pin Connector (D-SUB)
DVI-D 24pin Connector (DVI)
HDMI Connector (HDMI)
7
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
HDMI
<Front>
Power Switch (
DVI-D
D-SUB
ENGLISH
CONTROLS AND CONNECTORS : ProLite E2209HDS
AUDIO
<Back>
)
Power Indicator
NOTE Blue:
Normal operation
Orange: Power Management
The monitor enters into power management mode which reduces the power
consumption to less than 1W when receiving no horizontal and/or vertical
sync signal.
Menu / Select Button (MENU)
+ / Volune Button ( + )
- / ECO Mode Button ( - )
Auto Button (AUTO)
Speakers
AC Connector (AC IN)
Keyhole for Security Lock
NOTE You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
Headphone Connector (AUDIO)
Audio Connector (AUDIO)
D-SUB mini 15pin Connector (D-SUB)
DVI-D 24pin Connector (DVI)
HDMI Connector (HDMI)
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
8
CONNECTING YOUR MONITOR : ProLite B2209HDS
Ensure that both the computer and the monitor are switched off.
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor first and then to the power supply.
Turn on your monitor and computer.
ENGLISH
NOTE
The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If
a special cable is required please contact your local iiyama dealer or regional iiyama office.
For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama
office for a suitable adaptor.
Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
<Back>
Power Cable
(Accessory)
Audio Cable (Accessory)
D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable
(Accessory)
Computer
HDMI Cable (Not included)
[ Collect Cables ]
A Put the cables through the cable holder.
B Collect cables at the back of the stand.
9
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
AV Equipment
CONNECTING YOUR MONITOR : ProLite E2209HDS
Ensure that both the computer and the monitor are switched off.
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor first and then to the power supply.
Turn on your monitor and computer.
The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If
a special cable is required please contact your local iiyama dealer or regional iiyama office.
For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama
office for a suitable adaptor.
Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
<Back>
Power Cable
(Accessory)
Audio Cable (Accessory)
D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable
(Accessory)
Computer
HDMI Cable (Not included)
AV Equipment
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
10
ENGLISH
NOTE
COMPUTER SETTING
Signal Timing
Change to the desired signal timing listed on page 29: COMPLIANT TIMING.
Windows 95/98/2000/Me/XP/Vista/7 Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied.
ENGLISH
For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com
NOTE
For additional information on how to download the driver for your touch screen monitor,
please access the internet site noted above.
Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
11
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B2209HDS
For optimal viewing it is recommended to position
yourself directly opposite to the full face of the
monitor, then adjust the monitor’s height and
angle to your own preference.
Hold the panel so that the monitor does not topple
when you change the monitor’s height or angle.
You are able to adjust the monitor's height up to
ENGLISH
110mm
110mm, angle up to 170 degrees right and left, 20
degrees upward.
NOTE
Do not touch the LCD screen when you
change the height or the angle. It may
cause damage or break the LCD screen.
Careful attention is required not to catch
your fingers or hands when you change
the height or the angle.
ADJUSTING THE VIEWING ANGLE : ProLite E2209HDS
For optimal viewing it is recommended to look at the full face of
the monitor.
Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
You are able to adjust the monitor’s angle up to 20° upward, 5°
downward.
In order to ensure a healthy and relaxed body position
when using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed 10
20
degrees. Adjust the monitor’s angle to your own preference.
NOTE
Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD screen.
5
Careful attention is required not to catch your fingers
or hands when you change the angle.
Do not tilt the post beyond 20 degrees except when
repacking the monitor in its box.
To do so may cause the monitor to fall over and
break.
BEFORE YOU OPERATE THE MONITOR
Downloaded from ManualMonitor.com Manuals
12
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 29. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 20 for SCREEN ADJUSTMENTS.
Press the MENU Button to start the On Screen Display feature. There are additional
Menu items which can be switched by using the + / - Buttons.
ENGLISH
Luminance
Contrast
50
Brightness
50
Eco
Off
Picture Mode
ACR
Standard
ON
B Select the Menu item which contains the adjustment icon relating to the adjustment
you want to make. Press the MENU Button. Then, use the + / - Buttons to highlight
the desired adjustment icon.
C Press the MENU Button again. Use the + / - Buttons to make the appropriate
adjustment or setting.
D Press the AUTO Button to leave the menu, and the settings you just made would
be automatically saved.
For example, to correct for vertical position, select Menu item of Image Setup and then press the
MENU Button. Then, select V.Position by using the + / - Buttons.
An adjustment page appears after you press the MENU Button. Then, use the + / - Buttons to
change the vertical position settings. The vertical position of the overall display should be changing
accordingly while you are doing this.
Press the AUTO Button lastly, it ends, any changes are saved in the memory.
Image Setup
Clock
50
Phase
50
H.Position
50
V.Position
50
Aspect
Full
NOTE
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the Timeout has passed. Also, the AUTO button can be used to return previous menu
and turn off the On-Screen Display.
Any changes are automatically saved in the memory when the On Screen Display disappears.
Turning off the power should be avoided while using the Menu.
Adjustments for H. / V. Position, Clock and Phase are saved for each signal timing. Except for these
adjustments, all other adjustments have only one setting which applies to all signal timings.
13
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
ADJUSTMENT MENU CONTENTS
Luminance
Luminance
Contrast
50
Brightness
50
Eco
Off
Picture Mode
Standard
Adjustment Item
Problem / Option
Button to Press
Too dull
Contrast
Too intense
Too dark
Brightness *
Too bright
Off
Eco
ENGLISH
ON
ACR
Direct
Mode1
Mode2
Mode3
Brightness of back-light is reduced.
Brightness of back-light is reduced more than Mode1.
Brightness of back-light is reduced more than Mode2.
For general windows environment and monitor
Standard
default setting.
Internet
Game
Movie
Sport
For text editing and viewing in a word processing
environment.
For internet environment.
For PC game environment.
For movie and video environment.
For sport environment.
On
Increased Contrast Ratio
Off
Typical Contrast Ratio
Text
Picture Mode
ACR
Normal
NOTE ACR adjusts brightness according to the image, and improve the contrast ratio during
move playing.
Contrast, Brightness, sRGB, Eco and Picture Mode cannot be adjusted and selected while
ACR is active.
*
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
Direct
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Eco: Press the - Button when the Menu is not displayed.
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
14
Image Setup
Image Setup
Clock
50
Phase
50
H.Position
50
V.Position
50
Aspect
ENGLISH
Adjustment Item
Problem / Option
Too narrow
Clock*1,2
Phase*1,2
Too wide
To correct flickering text or lines
Too left
H. Position*2
Too right
Too low
V. Position*2
Aspect
Too high
Full
Expansion display
Aspect
Expansion display of Aspect
*1 See page 20 for SCREEN ADJUSTMENTS.
*2 Only Analog Input.
15
Full
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
Button to Press
Color Temp.
Color Temp.
Mode1
Color Temp.
Warm
User-R
50
User-G
50
User-B
50
Problem / Option
Mode1
Mode2
Mode3
Warm
Normal
Gamma
Cool
Color Temp.
User
sRGB
NOTE
Button to Press
ENGLISH
Adjustment Item
Gamma
Normal
Dark
High contrast
Greenish white
Yellowish white
Bluish white
User-R
User-G
User-B
sRGB
Too weak
Too strong
sRGB is an international standard which defines and unifies the difference of color
appearance between equipment.
You can not adjust the Brightness, Contrast, Gamma and Eco during sRGB mode
because those settings are locked.
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
16
OSD Setup
OSD Setup
H.Position
50
V.Position
50
Timeout
50
Language
ENGLISH
Adjustment Item
H.Position
V.Position
English
Problem / Option
Button to Press
OSD is too left
OSD is too right
OSD is too low
OSD is too high
Timeout
You can set the OSD display duration time
between 5 and 60 seconds.
Language
English
Deutsch
Français
Español
Italiano
17
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
English
German
French
Spanish
Italian
Portuguese
Portuguese
Simplified Chinese
Russian
Japanese
Others
Others
Input :
Resolution :
H.Frequency :
V.Frequency :
Adjustment Item
Reset
Signal Select
NOTE
Direct
Yes
Auto
Auto
HDMI
1920(H)㧖1080(V)
68KHz
60Hz
Problem / Option
Button to Press
Yes
Factory-preset data is restored.
No
Return to Menu.
Auto
Select the signal input automatically.
D-sub
DVI-D
HDMI
Select the D-SUB input.
Select the DVI-D input.
Select the HDMI input.
ENGLISH
Reset
Signal Select
HDMI audio
Information
At selected Auto, you can switch the input source by pressing and holding of the AUTO
Button for 1-2 seconds, However it will automatically be selected when just one source is
using.
In Power Management Mode input switching is disabled.
Input source is fixed, not selected automatically when D-sub, DVI-D and HDMI which are
selected.
HDMI audio*
Auto
Select the audio input automatically.
LINE IN
Select the LINE IN input.
Displays information regarding the current input signal coming
from the graphic card in your computer.
Information
NOTE See your graphic card user guide for more information
about changing the resolution and refresh.
* Suitable for HDMI input only.
Direct
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Signal Select: Pressing and holding of the AUTO Button for 1-2 seconds when the Menu is not
displayed.
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
18
Direct
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Volume: Press the + Button when the Menu is not displayed.
Adjustment Item
ENGLISH
Volume
Problem / Option
Button to Press
Too soft
Too loud
Only Analog Input
Auto Adjust: Press the AUTO Button when the Menu is not displayed.
Adjustment Item
Auto Adjust *
*
Problem / Option
Adjust H. / V. Position, Clock and Phase automatically.
For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 20 for
SCREEN ADJUSTMENTS.
19
Button to Press
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
The monitor is designed to provide the best performance at resolution of 1920 × 1080, but can not
provide the best at resolutions of less than 1920 × 1080 because the picture is automatically stretched
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Adjust depending on the resolution or signal
timing.
The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment
pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Clock and
Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.
com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista/7.
A Display the picture at the optimum resolution.
B Enter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE
NOTE
Consult the appropriate documentation for doing this.
Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting of
“Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Color bar
Zebra pattern
Picture frame
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
20
ENGLISH
to fit the full screen. It is recommended to operate at resolution of 1920 × 1080 in normal use.
C Press the Auto Button. (Auto Adjust)
D Adjust the image manually by following procedure below when the screen has a flicker or
blur, or the picture does not fit in the display area after performing the Auto Adjust.
ENGLISH
E Adjust the V.Position so that the top and bottom of the picture frame will fit to the display
area.
F 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge of
the display area.
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
NOTE
NOTE
When the left side of the picture frame moves apart from the left edge of the display
area during the Clock adjustment, adjust steps 1) and 2).
Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
The picture may flicker during the Clock, H.Position and V.Position adjustment.
In case the picture frame is bigger or smaller than the data display area after the Clock
adjustment, repeat steps from C.
21
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
NOTE
NOTE
In case the strong flicker or blurs remain on a part of the screen, repeat steps F and
G because the Clock may not be adjusted correctly. If the flicker or blurs still remain,
set the refresh rate of computer to low (60Hz) and repeat steps from C again.
Adjust the H.Position after the Phase adjustment if the horizontal position moves during
the adjustment.
H Adjust the Brightness and Color to get the desired picture after you complete the Clock and
Phase adjustments.
Put back your favorite wallpaper.
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
22
ENGLISH
G Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
POWER MANAGEMENT FEATURE
The power management feature of this product complies with power saving requirement of VESA
DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when
your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
ENGLISH
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor
enters into Power Management Mode which reduces the power consumption to less than 1W. The
screen becomes dark, and the power indicator turns to orange. From Power Management Mode,
the image reappears in several seconds when either the keyboard or the mouse are touched again.
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
Blue
Orange
POWER 0
1W
CONSUMPTION
NOTE
100%
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
23
OPERATING THE MONITOR
Downloaded from ManualMonitor.com Manuals
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3. If you are experiencing a problem which is not described below or you cannot correct the problem,
discontinue using the monitor and contact your dealer or iiyama service center for further assistance.
Check
ENGLISH
Problem
The picture does
not appear.
(Power indicator
does not light up.)
The Power Cable is firmly seated in the socket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
(Power indicator
is blue.)
If the blank screen saver is in active mode, touch the keyboard or the mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
(Power indicator
is orange.)
If the monitor is in power management mode, touch the keyboard or the mouse.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The screen is not
synchronized.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The video output level of the computer is within the specification of the monitor.
The screen
position is not in
the center.
The signal timing of the computer is within the specification of the monitor.
The screen is too
bright or too dark.
The video output level of the computer is within the specification of the
monitor.
The screen is
shaking.
The power voltage is within the specification of the monitor.
The signal timing of the computer is within the specification of the monitor.
TROUBLE SHOOTING
Downloaded from ManualMonitor.com Manuals
24
ENGLISH
Problem
Check
No sound.
The audio equipment (computer etc.) is ON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
The audio output level of the audio equipment is within the specification of
the monitor.
The sound is too
loud or too quiet.
The audio output level of the audio equipment is within the specification of
the monitor.
A strange noise is
heard.
The Audio Cable is properly connected.
RECYCLING INFORMATION
For better environment protection please don't dispose your monitor.
Please visit our web site: www.iiyama.com/recycle for monitor recycling.
25
TROUBLE SHOOTING / RECYCLING INFORMATION
Downloaded from ManualMonitor.com Manuals
APPENDIX
Size Category
22"
LCD Panel
Driving system
a-Si TFT Active Matrix
Size
Diagonal: 21.5" (55cm)
Pixel pitch
0.248mm H × 0.248mm V
Brightness
300cd/m2 (Typical)
Contrast ratio
1000 : 1 (Typical), ACR Function Available
Viewable angle
Right / Left : 85 degrees each, Up / Down: 80 degrees each (Typical)
Response time
5ms (Black, White, Black), 2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Analog: Horizontal: 24.0-80.0kHz, Vertical: 55-75Hz
Digital: Horizontal: 30.0-80.0kHz, Vertical: 55-75Hz
Maximum Resolution
1920 × 1080, 2.1 MegaPixels
Input Connector
D-Sub mini 15 pin, DVI-D 24 pin,HDMI
Plug & Play
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Input Video Signal
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance
Digital: HDMI (1.2)
Input Audio Connector
ø 3.5mm mini jack (Stereo)
Input Audio Signal
1.0Vrms maximum
Headphone Connector
ø 3.5mm mini jack (Stereo)
Speakers
2W × 2 (Stereo speakers)
Maximum Screen Size
477.5mm W × 268.6mm H / 18.8" W × 10.6" H
Power Source
100-240VAC, 50/60Hz, 1.5A
Power Consumption*
41W typical, Power management mode: 1W maximum
Dimensions / Net Weight
513.0 × 399.5-509.5 × 249.5mm / 20.2 × 15.7-20.1 × 9.8" (W×H×D)
6.3kg / 13.9lbs
Tilt Angle
Upward: 20 degrees Right / Left : 170 degrees each
5 to 35°C / 41 to 95°F
Environmental Considerations Operating: Temperature
10 to 80% (No condensation)
Humidity
Storage: Temperature -20 to 60°C / -4 to 140°F
5 to 85% (No condensation)
Humidity
Approvals
NOTE
TCO ’03, CE, TÜV-GS
* Audio equipment is not connected.
APPENDIX
Downloaded from ManualMonitor.com Manuals
26
ENGLISH
SPECIFICATIONS : ProLite B2209HDS
ENGLISH
SPECIFICATIONS : ProLite E2209HDS
Size Category
22"
LCD Panel
Driving system
a-Si TFT Active Matrix
Size
Diagonal: 21.5" (55cm)
Pixel pitch
0.248mm H × 0.248mm V
Brightness
300cd/m2 (Typical)
Contrast ratio
1000 : 1 (Typical), ACR Function Available
Viewable angle
Right / Left : 85 degrees each, Up / Down: 80 degrees each (Typical)
Response time
5ms (Black, White, Black), 2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Analog: Horizontal: 24.0-80.0kHz, Vertical: 55-75Hz
Digital: Horizontal: 30.0-80.0kHz, Vertical: 55-75Hz
Maximum Resolution
1920 × 1080, 2.1 MegaPixels
Input Connector
D-Sub mini 15 pin, DVI-D 24 pin,HDMI
Plug & Play
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Input Video Signal
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance
Digital: HDMI(1.2)
Input Audio Connector
ø 3.5mm mini jack (Stereo)
Input Audio Signal
1.0Vrms maximum
Headphone Connector
ø 3.5mm mini jack (Stereo)
Speakers
2W × 2 (Stereo speakers)
Maximum Screen Size
477.5mm W × 268.6mm H / 18.8" W × 10.6" H
Power Source
100-240VAC, 50/60Hz, 1.5A
Power Consumption*
41W typical, Power management mode: 1W maximum
Dimensions / Net Weight
513.0 × 366.0 × 181.5mm / 20.2 × 14.4 × 7.2" (W×H×D)
4.3kg / 9.5lbs
Tilt Angle
Upward: 20 degrees Downward : 5 degrees each
5 to 35°C / 41 to 95°F
Environmental Considerations Operating: Temperature
10 to 80% (No condensation)
Humidity
Storage: Temperature -20 to 60°C / -4 to 140°F
5 to 85% (No condensation)
Humidity
Approvals
NOTE
27
TCO ’03, CE, TÜV-GS, PSE
* Audio equipment is not connected.
APPENDIX
Downloaded from ManualMonitor.com Manuals
DIMENSIONS : ProLite B2209HDS
513.0mm/20.2"
479.5mm/18.9"
ENGLISH
(
249.5mm/9.8"
270.5mm/10.6"
308.5mm/12.1"
399.5mm/15.7" (509.5mm/20.1")
68.5mm/2.7"
) : Maximum adjustment range
DIMENSIONS : ProLite E2209HDS
513.0mm/20.2"
479.5mm/18.9"
181.5mm7.2"
270.5mm/10.6"
308.5mm/12.1"
366.0mm/14.4"
68.5mm/2.7"
220.5mm/8.7"
APPENDIX
Downloaded from ManualMonitor.com Manuals
28
COMPLIANT TIMING
PC Input
Horizontal
Frequency
Vertical
Frequency
Dot Clock
31.469kHz
59.940Hz
25.175MHz
37.500kHz
75.000Hz
31.500MHz
37.861kHz
72.809Hz
31.500MHz
35.156kHz
56.250Hz
36.000MHz
37.879kHz
60.317Hz
40.000MHz
46.875kHz
75.000Hz
49.500MHz
48.363kHz
60.004Hz
65.000MHz
56.476kHz
70.069Hz
75.000MHz
60.023kHz
75.029Hz
78.750MHz
63.981kHz
60.020Hz
108.000MHz
79.976kHz
75.025Hz
135.000MHz
55.935kHz
59.887Hz
106.500MHz
70.635kHz
74.984Hz
136.750MHz
WSXGA+ 1680 × 1050
65.290kHz
60.000Hz
146.250MHz
Full HD
1920 × 1080
640 × 480
832 × 624
66.590kHz
59.930Hz
138.500MHz
35.000kHz
66.667Hz
30.240MHz
*
49.725kHz
74.500Hz
57.283MHz
*
1024 × 768
60.150kHz
74.720Hz
80.000MHz
*
640 × 400
24.827kHz
56.424Hz
21.053MHz
*
Video Mode
VGA
ENGLISH
SVGA
VESA
XGA
SXGA
640 × 480
800 × 600
1024 × 768
1280 × 1024
WXGA+ 1440 × 900
Macintosh
PC9801
NOTE * Digital input is not compliant.
29
APPENDIX
M068A21
Downloaded from ManualMonitor.com Manuals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising