AcerPower F1/Aspire T310
Service Guide
Service guide files and updates are available
on the AIPG/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
AcerPower F1/Aspire T310
Service Guide
Service guide files and updates are available
on the AIPG/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on AcerPower F1/Aspire T310 service guide.
Date
2003/10/29
Chapter
Chapter 1
Updates
> Amend the FSB speed up to
800MHz on page 2
> Memory portion
> Memory combination portion
2003/12/18
II
Chapter 1
>Amend the Rear Panel and
mainboard layout without SATA
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
Chapter 1
System Specifications
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features & Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Acer Power F1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Acer Power F1 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Aspire T310/Acer Power F1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . 8
Power Management Function (ACPI support function) . . . . . . . . . . . . . . . 16
Chapter 2
System Utilities
17
Entering Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power Mangement Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
PnP/PCI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
PC Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Frequency/Voltage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Load Fail-Safe Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Load Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Set Supervisor/User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Save and Exit Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Exit Without Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Chapter 3
Machine Disassembly and Replacement
43
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Standard Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Opening the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the Modem card,CD-ROM,Floppy and HDD . . . . . . . . . . . . . . .46
Removing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Heatsink and the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the LED Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the Daughter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Standard Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Installing the Daughter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Installing the LED Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Installing the Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Installing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Installing the Heatsink and the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Installing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Installing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Installing the Modem card,CD-ROM, Floppy and HDD . . . . . . . . . . . . . . . .52
Installing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Installing the Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Closing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
VII
Table of Contents
Chapter 4
Troubleshooting
55
Power-On Self-Test (POST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Post Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
POST Error Messages List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Error Symptoms List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Chapter 5
Jumper and Connector Information
71
Checking Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Setting Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Checking Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Connecting Case Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Front Panel Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Connecting Optional Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chapter 6
FRU (Field Replaceable Unit) List
79
Appendix A
Model Definition and Configuration
91
Appendix B
Test Compatible Components
93
Microsoft WinXP Home Environment Test . . . . . . . . . . . . . . . . . . . . . . . . 94
Appendix C
VIII
Online Support Information
99
Chapter 1
System Specifications
Overview
The Aspire T310/AcerPower F1 supports Intel Pentium 4 Northwood based micro-ATX, IBM PC/AT
compatible system with PCI/AGP bus.
Chapter 1
1
Features & Specifications
CPU
T
Support Intel P4 Northwood (Socket 478) processor.
T
Support 800MHz, 533MHz or 400MHz FSB.
T
Support up to 3.06GHz+ P4 processor.
T
Support Intel Hyper Threading Technology.
Chipset
T
SiS 661FX, SiS964L
Memory
T
Socket Type: DDR-SDRAM PC2700/PC2100/PC3200(DDR400) 184-pin socket.
T
Support 64Mb, 128Mb, 256Mb, 512 Mb and 1Gb technologies.
T
Total: 64MB ~ 2GB (please refer to the AVL list for compatibility).
Graphics
T
On-die VGA
T
1 VGA port
AGP/PCI
T
One AGP 8X/4X 1.5V slot
T
Three PCI 2.2 5V slots
T
One FDD slot supports 1.44MB/3 mode 3.5” devices
T
Slot Type: 40 pin IDE slot
T
Slot Quantity: 2
T
Transfer rate support:
FDD
IDE
T
T
T
PIO Mode: 0/1/2/3/4
T
Ultra DMA 66/100/133
Storage Type support:
T
HDD/CD-ROM/CD-RW/DVD
T
Zip 250
ATA-100 transfer rate
Audio
T
Embedded RealTek ALC655 audio codec with 16-bit Sound Blaster compatibility
T
Chip (Additional): AC97 Codec, 20 bit with amplifier
T
Interface: AC Link
T
Channel: 6
T
Connectors support:
T
2
Line-in/Line-out (rear)
Chapter 1
T
Microphone-in (rear)/Microphone-in (front) (Default)
T
Headphone Out (front) (Default)
LAN
T
Supports 10/100MB ethernet environment
T
Connectors Quantity:
USB
T
T
On-board: 4 (rear)
T
Connector Pin: 4
Transfer Rate:
T
USB 2.0/1.1
BIOS
T
4MB Award BIOS with Plug and Play BIOS
T
ACPI, SMBIOS 2.3, Green and Boot Block.
T
Provides DMI 2.0, WFM 2.0, WOL, WOR, chassis intrusion and SM Bus for system management.
Others
Chapter 1
T
Suspend to RAM/Disk
T
PC2001 Compliant
T
Support PS2 Keyboard/Mouse and USB Keyboard/Mouse wake up function
3
Acer Power F1 Front Panel
The computer’s front panel consists of the following:
Label
4
Description
1
Optical Drive
2
FDD Drive
3
Power Button
4
Universal Serial Bus (USB) Ports
5
Microphone Jack
6
Speaker/Headphone jack
Chapter 1
Acer Power F1 Rear Panel
1
2
3
4
5
6
7
8
9
10
13
11
12
14
No.
Description
Label
No.
Description
1
Power Code Socket
2
Voltage Selector Switch
3
Fan Aperture
4
PS/2 Keyboard Port
5
PS/2 Mouse Connector
6
Serial Connector
7
Printer Connector
8
Monitor Connector
9
USB Connector
10
RJ-45 Ethernet Connector
11
Microphone Jack
12
Line-Out Jack
13
Line-In Jack
14
Extension Card Slots
Chapter 1
Description
5
Aspire T310/Acer Power F1
Label
6
Description
1394A2
IEEE 1394 Header
AGP1
Accelerated Graphics Port
ATX1
Standard 20-pin ATX power connector
ATX2
ATX12V power connector
AUDIO1
Front audio connector
AUXIN1
Auxiliary Audio input header
CASFAN1
Case fan connector
CDIN1
Primary CD-in Connector
COM2
Onboard serial port header COM2
CPU SOCKET
Micro PGA 478-pin socket for Pentium 4 CPUs
CPUFAN1
Cooling fan for CPU
DIMM1-DIMM2
Two 184-pin DDR SDRAM
Chapter 1
Label
Chapter 1
Description
FDD1
Floppy disk drive connector
IDE1
Primary IDE channel
IDE2
Secondary IDE channel
JP1
Clear CMOS jumper
JP3
BIOS flash protect jumper
NBFAN1
Cooling fan for NB
PANEL1
Connector for case front panel switches and LED
indicators
PCI1~PCI3
Three 32-bit add-on card slots
SATA1~SATA2
Two serial ATA headers
SJ1
Single color LED header
SPDIFO1
SPDIF out header
USB3 ~ USB4
Two connectors for front panel USB ports
7
Hardware Specifications and Configurations
Processor
Item
Specification
Type
Pentium 4
Socket
478
Speed
1.8G~3.06G and 3.2G
Minimum operating speed
0 MHz (If Stop CPU Clock in Sleep State in BIOS Setup is
set to Enabled.)
BIOS
Item
Specification
BIOS code programmer
Award
BIOS version
v6.0
BIOS ROM type
Flash ROM
BIOS ROM size
4MB
BIOS ROM package
32-pin DIP package
Support protocol
PCI 2.2, APM1.2, DMI 2.00.1, E-IDE, ACPI 1.0, ESCD 1.03,
ANSI ATA 3.0, PnP 1a, Bootable CD-ROM 1.0, ATAPI
Boot from CD-ROM feature
Yes
Support to LS-120 drive
No
Support to BIOS boot block feature
No
NOTE: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List
Hotkey
c
8
Function
Enter BIOS Setup Utility
Description
Press while the system is booting to
enter BIOS Setup Utility.
Chapter 1
This section has two table lists, system memory specification and the possible combinations of memory
module.
System Memory
Item
Specification
Memory socket number
2 sockets (4 banks)
Support memory size per socket
64MB / 128MB / 256MB/ 512MB/1G
Support maximum memory size
1G x2
Support memory type
DDR SDRAM
Support memory speed
DDR400/333/266
Support memory voltage
2.5 V
Support memory module package
184-pin DIMM
Support to parity check feature
Yes
Support to Error Correction Code (ECC)
feature
No
Memory module combinations
You can install memory modules in any combination as
long as they match the above specifications.
Memory Combinations
Slot
Memory Module
Total Memory
Slot 1
64, 128, 256, 512MB, 1G
64MB~1G
Slot 2
64, 128, 256, 512MB, 1G
64MB~1G
Maximum System Memory Supported
2G
Cache Memory
Item
Specification
First-Level Cache Configurations
Cache function control
Enable/Disable by BIOS Setup
Second-Level Cache Configurations
L2 Cache RAM type
PBSRAM
L2 Cache RAM size
Celeron: 128K
Intel P4: 256K/512K
PreScoot: 1024K
L2 Cache RAM speed
One-half the processor core clock frequency
L2 Cache RAM voltage
L2 Cache function control
Enable/Disable by BIOS Setup
L2 Cache scheme
Fixed in write-back
Video Memory
Item
Memory size
Chapter 1
Specification
32 MB or above
9
This section has two table lists, the video interface specification and its supported display modes.
Video Interface
Item
Specification
Video controller
661FX
Video controller resident bus
AGP bus
Video interface support
Video YUV texture in all texture formats
H/W DVD accelerator
Display Screen Resolution
Refresh Rate (Hz)
Hor. Scan (KHz)
Pixel Clock (MHz)
640x480
60
31.5
25.2
640x480
72
37.4
32.0
640x480
75
37.5
31.5
640x480
85
43.3
36.0
640x480
120
63.7
55.0
800x600
56
35.2
36.0
800x600
60
37.8
39.9
800x600
72
48.0
50.0
800x600
75
46.9
49.5
800x600
85
53.7
56.2
800x600
100
62.5
67.5
800x600
120
76.1
81.0
800x600
160
101.9
110.0
1024x768
70
56.5
75.0
1024x768
75
60.0
78.8
1024x768
100
79.0
110.0
1280x1024
43
50.0
80.0
1280x1024
60
64.0
110.0
1280x1024
85
91.2
157.5
1600x1200
60
76.2
156.0
1600x1200
85
106.2
229.5
Audio Interface
Item
10
Specification
Audio controller
SiS 964L
Audio controller resident bus
AC’97
Audio function control
Enable/disable by BIOS Setup
Mono or stereo
Stereo
Resolution
20 bits
Chapter 1
Audio Interface
Item
Specification
Compatibility
Sound Blaster Pro/16 compatible
Mixed digital and analog high performance chip
Enhanced stereo full duplex operation
High performance audio accelerator and AC’97 support
Full native DOS games compatibility
Virtual FM enhances audio experience through real-time FM-toWavetable conversion
MPU-401(UART mode) interface for wavetable synthesizers and
MIDI devices
Integrated dual game port
Meets AC’97and WHQL specifications
Music synthesizer
Yes, internal FM synthesizer
Sampling rate
48 KHz (max.)
MPU-401 UART support
Yes
Microphone jack
Supported
Headphone jack
Supported
IDE Interface
Item
Specification
IDE controller
SiS 964L
IDE controller resident bus
PCI bus
Number of IDE channel
2
Support IDE interface
E-IDE (up to PIO mode-4 and Ultra DMA 33/66), ANSIS ATA
rev.3.0 ATAPI
Support bootable CD-ROM
Yes
Floppy disk drive Interface
Item
Specification
Floppy disk drive controller
ITE 8705
Floppy disk drive controller resident
bus
ISA bus
Support FDD format
360KB, 720KB, 1.2MB, 1.44MB, 2.88MB
Chapter 1
11
Parallel Port
Item
Specification
Parallel port controller
ITE8705
Parallel port controller resident bus
ISA bus
Number of parallel ports
1
Support ECP/EPP
SPP / Bi-directional / ECP / EPP
Connector type
25-pin D-type female connector
Parallel port function control
Enable/disable by BIOS Setup
Optional ECP DMA channel
(in BIOS Setup)
DMA channel 1
DMA channel 3
Optional parallel port I/O address
(via BIOS Setup)
378h
278h
Optional parallel port IRQ
(via BIOS Setup)
IRQ5
IRQ7
Serial Port
Item
Serial port controller
Specification
ITE8705
Serial port controller resident bus
ISA bus
Number of serial port
2
16550 UART support
Yes
Connector type
9-pin D-type female connector
Optional serial port I/O address
(via BIOS Setup)
COM1: 2F8h, 3E8h, 2E8h
COM2: 3E8h, 3F8h, 2F8h
Optional serial port IRQ
(via BIOS Setup)
COM1: IRQ 3, and 4
COM2: IRQ 4, and 3
USB Port
Item
Specification
Universal HCI
USB 2.0
USB Class
Support legacy keyboard for legacy mode
Memory Address Map
Address
12
Size
Function
000000 - 07FFFF
512KBytes
Host Memory
080000 - 09FFFF
128KBytes
Host/PCI Memory
0A0000 - 0BFFFF
128KBytes
PCI/ISA Video Buffer Memory
0C0000 - 0C7FFF
32KBytes
Video BIOS Memory
0C8000 - 0DFFFF
96Kbytes
ISA Card BIOS & Buffer Memory
0E0000 - 0EFFFF
64Kbytes
BIOS Extension Memory
Setup and Post Memory
PCI Development BIOS
Chapter 1
Memory Address Map
Address
Size
0F0000 - 0FFFFF
Function
64Kbytes
System BIOS Memory
100000 - UPPER LIMIT
Main Memory
UPPER LIMIT - 4GBytes
PCI Memory
PCI INTx# and IDSEL Assignment Map
PCI INTx #
PCI Devices
Device IDSEL: ADxx
INTA#
ADIMM-slot
N
INTB#
PCI-Slot1
AD20
INTC#
PCI-Slot2
AD21
INTD#
PCI-Slot3
AD22
PCI Slot IRQ Routing Map
PCI INTX#
INTA
INTB
INTC
INTD
Bus Mastering
PCI slot 1
Route 4
Route 1
Route 2
Route 3
Enabled
PCI slot 2
Route 3
Route 4
Route 1
Route 2
Enabled
PCI slot 3
Route 2
Route 3
Route 4
Route 1
Enabled
I/O Address Map
Hex Range
000-01F
020-021
040-043
060-060
061-061
070-071
080-08F
0A0-0A1
0C0-0DF
0F0-0FF
170-177
1F0-1F7
278-27F
2F8-2FF
378-37F
3F0-3F5
3F6-3F6
3F7-3F7
3F8-3FF
0CF8
0CFC
778-77A
Chapter 1
Devices
DMA Controller-1
Interrupt Controller-1
System Timer
Keyboard Controller 8742
System Speaker
CMOS RAM Address and Real Time Clock
DMA Page Register
Interrupt Controller-2
DMA Controller-2
Math Co-Processor
Secondary IDE
Primary IDE
Parallel Printer Port 2
Serial Asynchronous Port 2
Parallel Printer Port 1
Floppy Disk Controller
Secondary IDE
Primary IDE
Serial Asynchronous Port 1
Configuration Address Register
Configuration Data Register
Parallel Printer Port 1
13
IRQ Assignment Map
IRQx
System Devices
Add-On-Card Devices
IRQ0
Timer
N
IRQ1
Keyboard
N
IRQ2
Cascade Interrupt Control
N
IRQ3
Serial Alternate
Reserved
IRQ4
Serial Primary
Reserved
IRQ5
MPU-401(Alternate)
Reserved
IRQ6
Floppy Disk
Reserved
IRQ7
Parallel Port
Reserved
IRQ8
Real Time Clock
N
IRQ9
N
Reserved
IRQ10
N
Reserved
IRQ11
N
Reserved
IRQ12
PS/2 Mouse
Reserved
IRQ13
Math Coprocessor Exception
N
IRQ14
Primary IDE
Reserved
IRQ15
Secondary IDE
Reserved
NOTE: N - Not be used
DRQ Assignment Map
DRQx
System Devices
Add-On-Card Devices
DRQ0
N
Reserved
DRQ1
N
Reserved
DRQ2
FDD
N
DRQ3
N
Reserved
DRQ4
Cascade
N
DRQ5
N
Reserved
DRQ6
N
Reserved
DRQ7
N
Reserved
NOTE: N - Not be used
Main Board Major Chips
Item
14
Controller
System core logic
SiS 661FX
Video controller
SiS 661FX
Super I/O controller
ITE8705
Audio controller
SiS 964L
LAN controller
RTL8100C
HDD controller
SiS 964L
Keyboard controller
SiS 964L
Chapter 1
Environmental Requirements
Item
Specifications
Temperature
Operating
+10 ~ +35°C
Non-operating
-20 ~ +60°C (Storage package)
Humidity
Operating
20% to 80% RH
Non-operating
20% to 80% RH
Vibration
Operating (unpacked)
5 ~ 16 Hz: 0.015 mm
16 ~ 250 Hz: 0.21 G
Non-operating (packed)
5 ~ 27.1 Hz: 0.6 G
27.1 ~ 50 Hz: 0.016 mm
50 ~ 500 Hz: 2 G
Mechanical Specifications
Item
Specification
Weight
One 3 ½ FDD and one 3.5 HDD
(without packing)
Varied by local configuration
Dimensions
(main footprint)
190mm * 320mm * 360mm
Switching Power Supply 200W
Input Frequency
Frequency Variation Range
50MHz
47MHz to 53MHz
60MHz
57MHz to 63MHz
Input Voltage
Variation Range
100 - 120 VRMS
90 - 132 VRMS
200 - 240 VRMS
180 - 264 VRMS
Input Current
Measuring Range
4A
90 -132 VRMS
2A
180 - 264 VRMS
Output Requirements
Regulation
Current Rating
+5V
+-5%
15A
+12V
+-5%
3A
-12V
+-10%
0.3A
+3.3V
+-4%
12A
+5Vaux
+-5%
3A
Chapter 1
15
Power Management Function (ACPI support function)
Device Standby Mode
T
Independent power management timer for hard disk drive devices
(0-15 minutes, time step=1 minute).
T
Hard disk drive goes into Standby mode (for ATA standard interface).
T
Disable V-sync to control the VESA DPMS monitor.
T
Resume method: device activated (Keyboard for DOS, keyboard & mouse for Windows).
T
Resume recovery time: 3-5 sec.
Global Standby Mode
T
Global power management timer (2-120 minutes, time step=10 minute).
T
Hard disk drive goes into Standby mode (for ATA standard interface).
T
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
T
Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
T
Resume recovery time: 7-10 sec.
Suspend Mode
T
Independent power management timer (2-120 minutes, time step=10 minutes) or pushing external
switch button.
T
CPU goes into SMM.
T
CPU asserts STPCLK# and goes into the Stop Grant State.
T
LED on the panel turns amber colour.
T
Hard disk drive goes into SLEEP mode (for ATA standard interface).
T
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
T
Ultra I/O and VGA chip go into power saving mode.
T
Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
T
Return to original state by pushing external switch button, modem ring in and USB keyboard for
ACPI mode.
T
ACPI specification 1.0b.
T
S0, S1, S3 and S5 sleep state support.
T
On board device power management support.
T
On board device configuration support.
ACPI
16
Chapter 1
Chapter 2
System Utilities
Most systems are already configured by the manufacturer or the dealer. There is no need to run
Setup when starting the computer unless you get a Run Setup message.
The Setup program loads configuration values into the battery-backed nonvolatile memory called CMOS RAM.
This memory area is not part of the system RAM.
NOTE: If you repeatedly receive Run Setup messages, the battery may be bad/flat. In this case, the system
cannot retain configuration values in CMOS.
Before you run Setup, make sure that you have saved all open files. The system reboots immediately after
you exit Setup.
Chapter 2
17
Entering Setup
Power on the computer abd the system will start POST (Power On Self Test)prosecc. When the message of
“Press DEL to enter SETUP” appears on the screen, press the key of [Delete] to enter the setup menu.
NOTE: If the message disappears before you respond and you still wish to enter Setup, restart the system by
turning it OFF and On. You may also restart the system by simultaneously pressing [Ctrl+Alt+Delete].
The Setup Utility main menu then appears:
The command line at the bottom of the menu tells you how to move within a screen and from one screen to
another.
T
To select an option, move the highlight bar by pressing
T
To change a parameter setting, press
T
Press
to return to the main menu. If you are already in the main menu, press
exit Setup.
or
or
then press
.
until the desired setting is found.
again to
The parameters on the screens show default values. These values may not be the same as those in your
system.
The grayed items on the screens have fixed settings and are not user-configurable.
NOTE: Due to the application of a new version of BIOS Setup program, you may find the BIOS menu is largely
different from the former models. However, you will soon find out that this version is much more
compact than the former ones.
18
Chapter 2
Product Information
The screen below appears if you select Product Information from the main menu:
The Product Information menu contains general data about the system, such as the product name, serial
number, BIOS version, etc. These information is necessary for troubleshooting (maybe required when asking
for technical support).
The following table describes the parameters found in this menu:
Parameter
Description
Product Name
Displays the model name of your system.
System S/N
Displays your system’s serial number.
Main Board ID
Displays the main board’s identification number.
Main Board S/N
Displays your main board’s serial number.
System BIOS Version
Specifies the version of your BIOS utility.
SMBIOS version
The System Management Interface (SM) BIOS allows you to check your system
hardware components without actually opening your system. Hardware checking
is done via software during start up. This parameter specifies the version of the
SMBIOS utility installed in your system.
BIOS Release Date
Displays the release date of the BIOS utility.
Chapter 2
19
Standard CMOS Features
Select Standard CMOS Features from the main menu to configure some basic parameters in your system.
The following screen shows the Standard CMOS Features menu:
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Date
Description
Lets you set the date following the weekdaymonth-day-year format
Options
Weekday: Sun, Mon...Sat
Month: Jan, Feb...Dec.
Day: 1 to 30
Year: 1980 to 2079
Time
Lets you set the time following the hour-minutesecond format
Hour: 0 to 23
Allows you to configure the hard disk drive
connected to the master port of IDE channel 0.
IDE Device Model Number:
None
Minute: 0 to 59
Second: 0 to 59
IDE Channel 0 Master
To enter the IDE Channel 0 Master setup, press
[Enter].
The IDE CD-ROM is always automatically
detected.
IDE Channel 0 Slave
Allows you to configure the hard disk drive
connected to the slave port of IDE channel 0.
IDE Device Model Number:
None
To enter the IDE Channel 0 Slave setup, press
[Enter].
The IDE CD-ROM is always automatically
detected.
20
Chapter 2
Parameter
IDE Channel 1 Master
Description
Allows you to configure the hard disk drive
connected to the master port of IDE channel 1.
Options
IDE Device Model Number:
None
To enter the IDE Channel 1 Master setup, press
[Enter].
The IDE CD-ROM is always automatically
detected.
IDE Channel 1 Slave
Allows you to configure the hard disk drive
connected to the slave port of IDE channel 1.
IDE Device Model Number:
None
To enter the IDE Channel 1 Slave setup, press
[Enter].
The IDE CD-ROM is always automatically
detected.
Drive A
Allows you to configure your floppy drive A.
1.44 MB, 3.5-inch
None
360 KB, 5.25-inch
1.2 MB, 5.25-inch
720 KB, 3.5-inch
2.88 MB, 3.5-inch
Drive B
Allows you to configure your floppy drive B.
1.44 MB, 3.5-inch
None
360 KB, 5.25-inch
1.2 MB, 5.25-inch
720 KB, 3.5-inch
2.88 MB, 3.5-inch
Floppy 3 Mode Support
Floppy 3 is the standard Japanese floppy drive
mode. Supported by the BIOS, the selected
diskette drive can read 720KB, 1.2MB and
1.44MB on a 3.5” diskette.
Disabled, Enabled
Video
This item specifies the type of video card in use.
The default setting is VGA/EGA. Since current
PCs use VGA only, this function is almost
useless and may be disregarded in the future.
VGA/EGA
This parameter enables you to control the
system stops in case of Power On Self Test
errors (POST).
All Errors
Halt On
CGA40
CGA80
Mono
No Errors
All but Keyboard
All but Diskette
All by Disk/Key
Base Memory
Refers to the option of memory that is available
to standard DOS programs. DOS systems have
an address space od 1MB, but the top 384KB
(called high memory) is reserved for system use.
This leaves 640 KB of conventional memory.
Everything above 1MB is either extended or
extended memory.
Extended Memory
Memory above and beyond the standard 1MB of
base memory that DOS supports. Extended
memory is only available in PCs with an Intel
80286 or later microprocessor. Extended
memory is not configured in any special manner
and is therefore unavailable to most DOS
programs. However, MS Windows and OS/2 can
use extended memory.
Total Memory
Total based and extended memory, and I/O ROM
384KB available to the system.
Chapter 2
21
IDE Channel 0/1 Master/Slave Setup
The following screen appears if you select any of the IDE drive parameters:
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Description
Options
IDE HDD AutoDetection
Auto-detects your hard disk drive
Press [Enter]
IDE Channel 0 Master
Display the type of device installed.
Auto
IDE Channel 0 slave
None
IDE Channel 1 Master
Manual
IDE Channel 1 Slave
Access Mode
Selects the HDD access mode
Auto
Large
LBA
CHS
22
Capacity
Shows the size of your HDD in MB
xxxxx MB
Cylinder
Shows your hard disk’s numberof cylinders
0 to 65535
Head
Shows your hard disk’s number of heads
0 to 255
Precomp
Selects the precomp number for old HDD parking
0 to 65535
Landing Zone
Selects the Land Zone number for old HDD parking
0 to 65535
Sector
Shows your hard disk’s number of sectors
0 to 255
Chapter 2
Advanced BIOS Features
The following screen shows the Advanced BIOS Features:
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Description
Options
CPU Feature
The items allow you to set the Thermal Monitor
1 (on die throtting) and the Thermal Monitor 2
(on ratio & VID transition).
Press [Enter]
Hard Disk Boot Priority
Selects the hard disk boot priority.
Press [Enter]
CPU L1 & L2 Cache
Uses internal level 1 (L1) and external level 2
(L2) cache memory to improve performance.
Enabled
Hyper-Threading
Technology
This item is only available when CPU and the
chipset support Hyper-Threading.
Enabled
Quick Power On Self Test
This parameter speeds up POST by skipping
some items that are normally checked.
Enabled
First / Second / Third Boot
Device
The items allow you to set the sequence of boot
device where BIOS attempts to load the disk
operating system.
Floppy, LS120, HDD-0, SCSI,
CDROM, HDD-1, HDD-2, HDD-3, ZIP,
LAN, Disabled (Disable this sequence
).
Disbaled
Disbaled
Disbaled
The sequence following the order of
HDD, Floppy and CD-ROM is
recommended.
Boot Other Device
Chapter 2
This parameter allows you to specify the system
boot up search sequence.
Enabled
Disbaled
23
Parameter
Description
Options
Swap Floppy Drive
Setting to Enabled will swap floppy drive a: and
b:.
Enabled
Boot Up Floppy Seek
Setting to Enabled will make BIOS seek floppy
drive a: before booting the system.
Enabled
Sets the NumLock status when the system is
powered on. Setting to On will turn on the
NumLock key when the system is powered on.
Setting to Off will allows users to use the arrow
keys on the numeric keypad.
On
This item is to set the Gate A20 status. A20
refers to the first 64KB of extended memory.
When the default value Fast is selected, the
Gate A20 is controlled by port 92 or chipset
specific method resulting in faster system
performance. When Normal is selected, A20 is
controlled by a keyboard controller or chipset
hardware.
Fast
This item enables or disables the display of the
ATA 66/100 IDE Cable Msg.
Enabled
This item is used to enable or disable the
typematic rate setting including Typematic Rate
and Typematic Deplay.
Enabled
Typematic Rate
After Typematic Rate Setting is enabled, this
item allows you to set the rate (characters/
second) at which at keys are accelerated.
Settings: 6,8,10,12,15,20,24 and 30.
Typematic Delay
This item allows you to select the delay
between when the key was first pressed and
when the acceleration begins
Settings: 250, 500, 750 and 1000.
Security Option
Specifies the type of BIOS password protection
that is implemented. Setup means that the
password prompt appears only when end users
try to run Setup. System means that a
password prompt appears every time when the
computer is powered on or when end users try
to run Setup.
Setup
This field is used to enable or disable the APIC
(Advanced Programmable Interrupt Controller).
Due to compliance with PC2001 design guide,
the system is able to run in APIC mode.
Enabling APIC mode will expand available IRQ
resources from the system.
Enabled
OS Select For DRAM >
64MB
This item is only required if you have installed
more than 64MB of memory and you are
running the OS/2 operating system.
Non-OS2
HDD S.M.A.R.T Capability
The S.M.A.R.T (Self-Monitoring, Analysis, and
Reporting Technology) system is a diagnostics
technology that monitors and predicts device
performance.
Enabled
This item determines whether the BIOS will be
copied to RAM for faster execution.
Enabled
Silent Boot
Enables or disables the display of the logo
during boot.
Enabled
Configuration Table
Enables or disables the configuration table.
Enabled
Boot Up NumLock Status
Gate A20 Option
ATA 66/100 IDE Cable Msg.
Typematic Rate Setting
APIC Mode
Video BIOS Shadow
Disabled
Disabled
Off
Normal
Disbaled
Disabled
System
Disabled
OS2
Disabled
Disabled
Disabled
Disabled
24
Chapter 2
Advanced Chipset Features
The advanced cipset features setup option is used to change the values of the chipset registers. These
registers control most of the system options in the computer.
NOTE: Change these settings only if you are familiar with the chipset.
DRAM Clock/Timing Control
Press [Enter] to enter the sub-menu and the following screen appears:
Chapter 2
25
The following table describes each parameter under the sub-menu. Settings in boldface are the default and
suggested values.
Parameter
Description
Options
Current CPU Frequency /
Current DRAM Frequency
Shows the CPU and DRAM frequency.
Performance Mode
Enables this item to enhance the system
performance.
Enabled
DRAM Timing Control
Enables you to select the CAS latency time in
HCLKs of 2, 2.5, or 3. The value is set at the
factory depending on the DRAM installed. Do not
change the values in this field unless you change
specifications of the installed DRAM or the
installed CPU.
By SPD
DRAM CAS Latency
This item controls the timing delay (in clock
cycles) before the DRAM starts a read command
after receiving it.
2T, 2.5T, 3T
RAS Active Time(tRAS)
This item allows you to set the amount of time a
RAS can be kept open for multiple accesses.
High figures will improve performance.
4T, 5T, 6T, 7T, 8T, 9T
RAS Precharge Time(tRP)
This is the duration of the time interval during
which the Row Address Strobe signal to a DRAM
is held low during normal Read and Write Cycles.
This is the minimum interval between completing
one read or write and starting another from the
same (non-page mode) DRAM. Techniques such
as memory interleaving, or use of Page Mode
DRAM are often used to avoid this delay. Some
chipsets require this parameter in order to set up
the memory configuration properly. The RAS
Precharge value is typically about the same as
the RAM Access (data read/write) time.
2T, 3T, 4T, 5T
RAS to CAS Delay(tRCD)
This is the amount of time a CAS is performed
after a RAS. The lower the better, but some
DRAM does not support low figures.
2T, 3T, 4T, 5T
Disabled
Manual
The other two parameters under the Advanced Chipset Features are presented below. Settings in boldface
are the deafult and suggested values.
AGP & P2P Bridge Control
Press [Enter] to enter the sub-menu and the following screen appears:
Description
Options
AGP Aperture Size
Parameter
This setting controls just how much system RAM
can be allocated to AGP for video purposes. The
aperture is a portion of the PCI memory address
range dedicated to graphics memory address
space. Host cycles that hit the aperture range are
forwarded to the AGP without any translation.
32MB, 64MB, 128MB, 256MB,
512MB
Graphic Window WR
Combin
This item determines whether the graphic
windows base address is valid or not.
Enabled
AGP Fast Write Support
Enables and disables AGP Fast Write Support.
Disabled
AGP Data Rate
This item allows you to control AGP card data
transfer rate.
Disabled
Enabled
26
Auto, 1x, 2x, 4x ,8x
Chapter 2
OnChip AGP Control
Press [Enter] to enter the sub-menu and the following screen appears:
Parameter
VGA Share Memory Size
Parameter
System BIOS Cacheable
Description
Selects the VGA share memory size
Options
16, 32MB, 64MB, 128MB
Description
Options
Enables or disables the system BIOS cacheable. Disabled
Enabled
Video RAM Cacheable
Enables or disables the video RAM cacheable.
Disabled
Enabled
Chapter 2
27
Integrated Peripherals
The following table describes each Integrated Peripherals parameters. Settings in boldface are the default
and suggested values.
SIS OnChip IDE Device
Press [Enter] to enter the sub-menu and the following screen appears:
Parameter
Options
This setting enables or disables the internal
primary and secondary PCI & IDE controllers.
Both, Disabled, Primary,
Secondary
IDE Primary Master PIO
Setting these items to “Auto” activates the HDD
speed auto-detect function. The PIO mode
specifies the data transfer rate of the HDD. For
example, mode 0 data transfer rate is 3.3MB/s,
mode 1 is 5.2 MB/s, mode 2 is 8.3MB/s, mode 3
is 11.1 MB/s and mode 4 is 16.6MB/s. If your
hard disk performance becomes unstable, you
may manually try the slower mode.
Auto, mode 1, mode 2, mode 3
and mode 4
IDE Primary Slave PIO
IDE Secondary Master PIO
IDE Secondary Slave PIO
28
Description
Internal PCI/IDE
Primary Master UltraDMA
These items allow you to set the Ultra DMA 33/
66/100 mode supported by the hard disk drive
Secondary Master UltraDMA connected to your primary and secondary IDE
connectors.
Secondary Slave UltraDMA
Auto
Primary Salve UltraDMA
Disables
IDE DMA Transfer Access
This item allows you to enabled the transfer
access of the IDE DMA.
Enabled
IDE Burst Mode
This allows your hard disk controller to use the
fast block mode to transfer data to and from the
hard disk drive.
Enabled
Disabled
Disabled
Chapter 2
SIS OnChip PCI Device
Press [Enter] to enter the sub-menu and the following screen appears:
Parameter
USB Controller
USB Ports Number
Description
Options
This item enables the USB controller. Leave this
at the default “Enabled”, if you want to connect
USB devices to your computer.
Enabled
This item enables you to determine the number
of USB ports.
6 Potrs
Disabled
5 Potrs
4 Potrs
3 Potrs
USB 2.0 Support
Enable this item if the system supports USB 2.0
Enabled
Disabled
This item allows the BIOS to interact with a USB
keyboard or mouse to work with MS-DOS based
utilities and non-Windows modes.
Enabled
This item lets you enable or disable the USB
mouse driver within the onboard BIOS. The
keyboard driver simulates legacy mouse
command and lets you use a USB mouse during
POST or after boot if you do not have a USB
driver in the operating system.
Enabled
This option allows you to control the onboard
AC97 audio. Disable this item if you are going to
install a PCI audio add-on card.
Enabled
SIS Serial ATA Controller
This item allows you to control the SiS Serial ATA
controller.
Enabled
SIS Serial ATA Mode
This item allows you to change SiS Serial ATA
mode.
IDE
USB Legacy Support
USB Mouse Support
SIS AC97 AUDIO
Disabled
Disabled
Disabled
Disabled
RAID
Onboard SuperIO Device
Press [Enter] to enter the sub-menu and the following screen appears:
Parameter
Onboard FDC Controller
Description
Options
Enables or disables the onboard floppy disk drive
controller.
Enabled
Onboard Serial Port 1
This option is used to assign the I/O address and
interrupt request (IRQ) for onboard serial port 1
(COM1).
Disable, 3F8/IRQ4, 2F8/IRQ3,
3E8/IRQ4, 2E8/IRQ3, Auto
Onboard Serial Port 2
This option is used to assign the I/O address and
interrupt request (IRQ) for onboard serial port 1
(COM2).
Disable, 3F8/IRQ4, 2F8/IRQ3,
3E8/IRQ4, 2E8/IRQ3, Auto
Onboard Parallel Port
This option is used to assign the I/O address and
interrupt request (IRQ) for the onboard parallel
port.
Disabled, 378/IRQ7, 278/IRQ5,
3BC/IRQ7
Parallel Port Mode
Enables you to set the data transfer protocol for
your parallel port.
SPP, EPP, ECP, ECP+EPP
Disabled
SPP (Standard Parallel Port), EPP (Enhanced
Parallel Port), ECP (Extended Capabilities Port)
and ECP+EPP.
ECP Mode Use DMA
Chapter 2
When the onboard parallel port is set to ECP
3, 1
mode, the parallel port can use DMA 3 or DMA 1.
29
Parameter
Description
Options
SIS Serial ATA Controller
This item allows you to control the SiS Serial ATA
controller.
Enabled
SIS Serial ATA Mode
This item allows you to change SiS Serial ATA
mode.
IDE
Parameter
Disabled
RAID
Description
Onboard 1394 Device
(optional)
Enables or disables the onboard 1394.
Onboard LAN function
Enables and disables the onboard LAN.
Options
Enabled
Disabled
Enabled
Disabled
Onboard LAN Boot ROM
IDE HDD Block Mode
Init Display First
30
Use this item to enable and disable the booting
from the onboard LAN or a network add-in card
with a remote boot ROM installed.
Enabled
Enable this field if your IDE hard drive supports
block mode. Block mode enables BIOS to
automatically detect the optimal number of block
read and writes per sector that the drive can
support. It also improves the speed of access to
IDE devices.
Enabled
Use this item to specify whether your graphics
adapter is installed in one of the PCI slots or is
integrated on the motherboard.
PCI Slot
Disabled
Disabled
AGP
Chapter 2
Power Management Setup
The Power Management menu lets you configure your system to most effectively save energy while operating
in a manner consistent with your own style of computer use.
The following screen shows the Power Management parameters and their default settings:
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
ACPI Suspend Type
Suspend Mode
Chapter 2
Description
Options
This item specifies the power saving modes for
ACPI function. S1(POS): The S1 sleep mode is
a low power state. In this state, no system
context (CPU or chipset) is lost and hardware
maintains all system context. S3 (STR): The S3
sleep mode is s power-down state in which
power is supplied only to essential components
such as main memory and wake-capable
devices and all system context is saved to main
memory. The information stored in memory will
be used to restore the PC to the previous state
when an wake-up event occurs. S1&S3: Both S1
and S3 will be adopted.
S3
The CPU clock will be stopped and the video
signal will be suspended if no Power
Management events occur for a specified length
of time. Full power function will return when a
Power Management event is detected.
Disabled, 1 Min, 2 Min, 4 Min,
8 Min, 12 Min, 20 Min, 30 Min,
40 Min, 1Hour
S1
S1&S3
31
Parameter
Description
Options
This item is to control the mode in which the
monitor will shut down.
Always On
Always On: Always keep the monitor on.
Suspend --> Off: During suspend mode, the
monitorwill shut down. Susp, Stby --> During
suspend or standby mode, the monitor will shut
down. All Modes --> Off: The monitor is turned
off during doze, standby or suspend mode.
Susp, Stby --> Off
This item determines the manner in which the
monitor is blanked.
V/H SYNC+Blank
V/H SYNC+Blank: This selection will cause the
system to turn off the vertical and horizontal
synchronization ports and write blanks to the
video buffer. Blank Screen: This option only
write blanks to the video buffer. DPMS
Supported: Initial display power management
signaling.
DPMS Supported
Modem Use IRQ
This setting names the interrupt request (IRQ)
line assigned to the modem (if any) on your
system. Activity of selected IRQ always
awakens the system.
3, 4, 5, 7, 9, 10, 11, AUTO
Hot Key Function As
This option allows you to set the Hot Key
functionality
Disable
Video Off Option
Video Off Method
Suspend Off
All Modes
Blank Screen
Power Off
Suspend
HDD Power Down
Soft-off by PWR-BTTN
If HDD activity is not detected for the length of
time specified in this field, the hard disk drive will
be powered down while all other devices remain
active.
Disabled
This feature allows users to configure the power
button function.
Instant Off: The power button
functions as a normal poweron/-off button.
1~15 Mins
Delay 4 Sec: When you press
the power button, the
computer enters the suspend/
sleep mode, but if the button is
pressed for more than four
seconds, the computer will be
turned off.
Aftrer PC Power Lose
This item specifies when your system reboot
after a power failure or interrupt occurs.
Off
On
Former-Sts
Delay Prior to Thermal
Enables you to set the delay time before the
CPU enters auto thermal mode.
None
1 Min, 2 Min, 4 Min, 8 Min, 16
Min, 32 Min, 64 Min
PM Wake Up Events
Press [Enter] to enter the sub-menu and the following screen appears:
32
Chapter 2
The following table describes each parameter under the sub-menu. Settings in boldface are the default and
suggested values.
Parameter
Description
Options
This option determines whether any activity for
IRQ 3-7/9-15 will cause the system to wake from
a power saving mode.
Enabled
Determines whether the system will monitor IRQ
8 activity and wake the system from a power
saving mode when IRQ 8 is activated.
Enabled
An input signal on the serial Ring Indicator (RI)
line (in other words, an incoming call on the
modem) awakens the system from a soft off
state.
Enabled
This item specifies whether the system will be
awakened from power saving modes when
activity or input signal of the specified hardware
peripheral or component is detected.
Enabled
This option allows you to specify whether the
system will be awakened from power saving
modes when activity or input signal of the
specified hardware peripheral or component is
detected.
Enabled
PS2KB Wakeup from S3
This option allows you to set hot key combination
to turn on the system by keyboard.
Hot Key
PS2MS Wakeup from S3
This option allows you to set the mouse action to
turn on the system.
Enabled
Resume by Alarm
When set to Enabled, the following three fields
become available: Month Alarm, Day of Month
Alarm, and Time Alarm Upon arrival of the alarm
time, it will instruct the system to wake up.
Enabled
IRQ [3-7, 9-15], NMI
IRQ 8 Break Suspend
Power On by Ring
Wake-Up by PCI Card
USB Port Wakeup from S3
Chapter 2
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
33
Parameter
Primary/Secondary IDE
FDD, COM, LPT Port
PCI PIRQ[A-D]#
34
Description
Options
When this item is enabled, the system power will
resume the system from a power saving mode if
there is any activity on primary or secondary IDE
channels 0 or 1.
Enabled
When this item is enabled, the system will restart
the power-saving timeout counters when any
activity is detected on the floppy disk drive, serial
ports, or the parallel port.
Enabled
When this item is enabled, any activity from one
of the listed devices wakes up the system.
Enabled
Disabled
Disabled
Disabled
Chapter 2
PnP/PCI Configuration
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Reset Configuration Data
Resources Controlled By
Description
Options
Selecting “Enabled” to reset Extended System
Configuration Data (ESCD) only if you installed
a new add-on and the system reconfiguration
has caused such a serious conflict that the
operating system can not boot. Otherwise, you
should leave it unchanged.
Disabled
This BIOS can automatically configure all of the
boot and Plug and Play compatible devices.
You can also set it as Manual and go into each
of the sub menu to choose specific resources.
Auto (ESCD)
Enabled
Manual
IRQ Resources
The items are adjustable only when “Resources PCI Device
Controlled By” is set to Manual. By pressing
Reserved
“Enter” to access the sub menu.
PCI/VGA Palette Snoop
Disabled - Data read or written by the CPU is
only directed to the PCI VGA device’s palette
registers.
Enabled - Data read or written by the CPU is
directed to both the PCI VGA device’s palette
registers and the ISA VGA device’s palette
registers, permitting the palette registers of both
VGA devices to be identical.
Disabled
Enabled
*If any ISA bus adapter in the
system requires VGA Palette
snooping, the setting must be set
to “Enabled”.
NOTE: It is strongly recommended that only experienced users should make any changes to the default
settings.
Chapter 2
35
PC Health Status
The following table describes the parameters found in this menu:
36
Parameter
Description
Shutdown Temperature
This option is for setting the shutdown temperature
level for the processor. When the processor
reaches the temperature you set, the ACPI-aware
system will be shut down.
System Component
Characteristics
These items display the current status of all of the
mainboard hardware devices/components such as
CPU voltages, temperatures and all fans’ speeds.
Options
Chapter 2
Frequency/Voltage Control
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Description
Options
CPU Clock Ratio
If the CPU Ratio is set to Manual, end users can
choose a suitable ratioto support the CPU.
8x to 50x
Auto Detect DIMM/PCI Clk
This option allows you to enable/disable the
feature of auto detecting the clock frequency of
the installed DIMM/PCI bus.
Enabled
When the motherboard’s clock generator pulses,
the extreme values (spikes) of the pulses creates
EMI (Electromagnetic Interference). The spread
Spectrum function reduces the EMI generated by
modulating the pulses so that the spikes of the
pulses are reduced to flatter curves. If you do
not have any EMI problem, leave the setting at
Disabled for optimal system stability and
performance. But if you are plagued by EMI,
setting to Enabled for EMI reduction. Remember
to disable Spread Spectrum if you are
overlocking because even a slight jitter can
introduce a temporary boost in clockspeed which
may just cause your overlock ed processor to
lock up.
Enabled
Spread Spectrum
Chapter 2
Disabled
Disabled
37
Load Fail-Safe Defaults
This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility:
Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The
fail-safe defaults place no great demands on the system and are generally stable. If your system is not
functioning correctly, try installing the fail-safe defaults as a first step in getting your system working properly
again. If you only want to install fail-safe defaults for a specific option, select and display that option.
38
Chapter 2
Load Default Settings
This option opens a dialog box that lets you install defaults for all appropriate items in the Setup Utility.
Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The
defaults place demands on the system that may be greater than the performance level of the components,
such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults
when your hardware does not support them. If you only want to install setup defaults for a specific option,
select and display that option.
Chapter 2
39
Set Supervisor/User Password
When this function is selected, the following message appears at the center of the screen to assist you in
creating a password.
Type the password, up to eight characters, and press <Enter>. The password typed now will clear any
previously entered password from CMOS memory. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also press <Esc> to abort the selection.
To disable password, just press <Enter> when you are prompted to enter password. A message will confirm
the password being disabled. Once the password is disabled, the system will boot and you can enter BIOS
Setup freely.
If you have selected “System” in “Security Option” of “BIOS Features Setup” menu, you will be prompted for
the password every time the system reboots or any time you try to enter BIOS Setup.
If you have selected “Setup” at “Security Option” from “BIOS Features Setup” menu, you will be prompted for
the password only when you enter BIOS Setup.
Supervisor Password has higher priority than User Password. You can use Supervisor Password when
booting the system or entering BIOS Setup to modify all settings. Also you can use User Password when
booting the system or entering BIOS Setup but can not modify any setting if Supervisor Password is enabled.
40
Chapter 2
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the
Setup Utility.
When the Save and Exit dialog box appears, press <Y> to save and exit, or press <N> to return to the main
menu.
Chapter 2
41
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit
the Setup Utility.
When the Exit Without Saving dialog box appears, press <Y> to discard changes and exit, or press <N> to
return to the main menu.
NOTE: If you have made settings that you do not want to save, use the "Exit Without Saving" item and press
<Y> to discard any changes you have made.
42
Chapter 2
Chapter 3
Machine Disassembly and Replacement
Please also refer to the AcerPower F1 Service CD for the assembly/disassembly procedure.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge.
T
Wire cutter.
T
Phillips screwdriver (may require different size).
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatches when putting back the components.
NOTE: The AcerPower F1 mechanical housing is similar with AcerPower SV.
Chapter 3
43
General Information
Before You Begin
Before proceeding with the disassenbly procedure, make sure that you do the following:
44
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
Chapter 3
Standard Disassembly Procedure
This section tells you how to disassemble the system when you need to perform system service. Please also
refer to the disassembly video, if available.
CAUTION: Before you proceed, make sure you have turned off the system and all peripherals connected to it.
Opening the System
1.
Place the system unit on a flat, steady surface.
2.
Turn the housing back, and remove the screws as shown here.
3.
Slide the side door out. Then remove it.
Removing the Front Panel
1.
Release the six latches behind the front bezel.
2.
Remove the bezel by following the instruction below.
Removing the Cables
1.
Disconnect the Aux-In cable.
Chapter 3
45
2.
Disconnect the CD-In cable.
3.
Disconnect the floppy cable.
4.
Disconnect the IDE1 and IDE2 cable.
Removing the Modem card, CD-ROM, Floppy and HDD
46
1.
Detach the modem card.
2.
Disconnect the CD-ROM power, IDE and CD-In cables.
3.
Disconnect the floppy cable and power cable.
4.
Disconnect the HDD power cable and IDE cable.
Chapter 3
5.
Press the latch and remove the CD-ROM drive.
6.
Press the latch and remove the floppy drive.
7.
Press the latch again to release the hard disk module.
8.
Detach the HDD from the bracket.
Removing the Power Supply
1.
Remove the main ATX power connector as shown here.
2.
Remove the Pentium 4(ATX-12V) power connector as shown here.
3.
Remove the four screws as shown here.
Chapter 3
47
4.
Remove the power supply.
Removing the Heatsink and the CPU
1.
Disconnect the Pentium 4 CPU power cable.
2.
Release the two heatsink latches.
3.
Remove the heatsink module.
4.
Remove the CPU by following the instructions here.
Removing the Memory
1.
48
Pop out the memory and remove it as shown here.
Chapter 3
Removing the Mainboard
1.
Remove the six screw as shown here.
2.
Remove the motherboard as shown here.
Removing the Power Button
1.
Remove the power button as shown here.
Removing the LED Module
1.
Remove the LED module by following the instructions here.
Removing the Daughter Board
1.
Remove the screw as shown here.
2.
Detach the USB cable and audio cable from the daughter board.
Chapter 3
49
Standard Reassembly Procedure
This section tells you how to reassemble the system when you need to perform system service. Please also
refer to the assembly video, if available.
Installing the Daughter Board
1.
Connect the audio cable and USB cables to the daughter board.
2.
Fasten the daughter board with one screw as shown here.
Installing the LED Module
1.
Install the LED module by following the instructions here.
Installing the Power Button
1.
Attach the power button as shown here.
Installing the Mainboard
1.
50
Put the motherboard to the original position as shown here.
Chapter 3
2.
Secure the motherboard with the six screw as shown here.
Installing the Heatsink and the CPU
1.
Place the CPU to the CPU socket by following the instructions here.
2.
Place the heatsink module.
3.
Secure the heatsink with the two heatsink latches.
4.
Connect the Pentium 4 CPU power cable.
Installing the Memory
1.
Insert the memory to the DIMM slot as shown here.
Chapter 3
51
Installing the Power Supply
1.
Place the power supply to the original position as shown here.
2.
Secure the power supply with the four screws as shown here.
3.
Connect the Pentium 4(ATX-12V) power connector to the motherboard as shown here.
4.
Connect the main ATX power connector to the motherboard as shown here.
Installing the Modem card, CD-ROM, Floppy and HDD
52
1.
Insert the HDD to the bracket by following the instructions here.
2.
Place the HDD module back to the original position.
3.
Place the floppy drive back to the original position.
Chapter 3
4.
Place the CD-ROM drive back to the original position.
5.
Connect the HDD power cable and IDE cable.
6.
Connect the floppy cable and power cable.
7.
Connect the CD-ROM power, IDE and CD-In cables.
8.
Place the modem card back to one PCI slot. Then secure the modem card with the screw.
Installing the Cables
1.
Connect the IDE1 and IDE2 cable to the motherboard.
2.
Connect the floppy cable to the motherboard.
Chapter 3
53
3.
Connect the CD-In cable to the motherboard.
4.
Connect the Aux-In cable to the motherboard.
Installing the Front Panel
1.
Place the front bezel back to the original position.
Closing the System
54
1.
Place the side door back to the original position.
2.
Secure the side door with the two screws as shown here.
Chapter 3
Chapter 4
Troubleshooting
This chapter provides troubleshooting information for the AcerT310/AcerPower F1:
Chapter 4
T
Power-On Self-Test (POST)
T
Index of Error Messages
T
Index of Error Codes and Error Beeps
T
Index of Error Symptoms
T
Undetermined Problems
55
Power-On Self-Test (POST)
Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during
POST, but is for the most part transparent to the user.
The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the
system components, and controls the operation of the power-on password option. If POST discovers
errors in system operations at power-on, it displays error messages on screen, generates a check
point code at port 80h or even halts the system if the error is fatal.
The main components on the main board that must be diagnosed and/or initialized by POST to ensure
system functionality are as follows:
56
T
Microprocessor with built-in numeric co-processor and cache memory subsystem
T
Direct Memory Access (DMA) controller
T
Interrupt system
T
Three programmable timers
T
ROM subsystem
T
RAM subsystem
T
RTC RAM subsystem and real time clock/calendar with battery backup
T
Onboard serial interface controller
T
Onboard parallel interface controller
T
Embedded hard disk interface and one diskette drive interface
T
Keyboard and auxiliary device controllers
T
I/O ports
T
PS/2-compatible mouse port
T
PS/2-compatible keyboard port
T
Serial ports
T
Parallel ports
T
USB port
Chapter 4
POST Check Points
When POST executes a task, it uses a series of preset numbers called check point to be latched at port 80h,
indicating the stages it is currently running. This latch can be read and shown on a debug board.
The following table describes the Acer common tasks carried out by POST. A unique check point number
represents each task.
Checkpoint
Description
CFh
Test CMOS R/W functionality
C0h
Early chipset initialization:
•
•
•
C1h
Detect memory
•
•
Chapter 4
Disable shadow RAM
Disable L2 Cache (socket 7 or below)
Program basic chipset registers
Auto-detection of DRAM size, type and ECC.
Auto-detection of L2 cache (socket 7 or below)
C3h
Expand compressed BIOS code to DRAM
C5h
Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM
0h1
Expand the Xgroup codes locating in physical address 1000:0
02h
Reserved
03h
Initial Superio_Early_Init switch
04h
Reserved
05h
1. Blank out screen
2. Clear CMOS error flag
06h
Reserved
07h
1. Clear 8042 interface
2. Initialize 8042 self-test
08h
1. Test special keyboard controller for Winbond 977 series
Super I/O chips
2. Enable keyboard interface
09h
Reserved
0Ah
1. Disable PS/2 mouse interface (optional)
2. Auto detect ports for keyboard & mouse followed by a port
& interface swap (optional)
3. Reset keyboard for Winbond 977 series Super I/O chips
0Bh
Reserved
0Ch
Reserved
0Dh
Reserved
0Eh
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails. keep beeping the speaker.
0Fh
Reserved
10h
Auto detect flash type to load appropriate flash R/W codes into
the run time area in F000 for ESCD & DMI support.
11h
Reserved
57
Checkpoint
Description
12h
Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for
override.
13h
Reserved
14h
Program chipset default values into chipset. Chipset default values are MODBINable by OEM customers.
15h
Reserved
16h
Initial onboard clock generator if Early_Init_Onboard_Generator
is defined. See also POST 26h.
17h
Reserved
18h
Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).
19h
Reserved
1Ah
Reserved
1Bh
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.
1Ch
Reserved
1Dh
Initial EARLY_PM_INIT switch
1Eh
Reserved
1Fh
Load keyboard matrix (notebook platform)
20h
Reserved
21h
HPM Initialization (notebook platform)
22h
Reserved
23h
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If Smos checksum
fails, use default value instead.
24h
Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy information.
25h
Early PCI Initialization:
•
•
•
58
Enumerate PCI bus number
Assign memory & I/O resource
Search for a valid VGA device & VGA BIOS, and put it into
C000:0
26h
1. If Early_Init_Onboard_Generator is not defined Onboard
clock generator initialization. Disable respective clock
resource to empty PCI & DIMM slots.
2. Init onboard PWM
3. Init onboard H/W monitor devices
27h
Initialize INT 09 buffer
28h
Reserved
29h
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address.
2. Initialize the APIC for Pentium class CPU
3. Program early chipset according to CMOS setup. Example:
onboard IDE controller.
4. Measure CPU speed.
Chapter 4
Checkpoint
Chapter 4
Description
2Ah
Reserved
2Bh
Invoke Video BIOS
2Ch
Reserved
2Dh
1. Initialize double-byte language font (Optional)
2. Put information on screen display, including Award title,
CPU type, CPU speed, full screen logo.
2Eh
Reserved
2Fh
Rederved
30h
Reserved
31h
Reserved
32h
Reserved
33h
Reset keyboard if Early_Reset_KB is defined e.g. Winbond 977
series Super I/O chips. See also POST 63h
34h
Reserved
35h
Test DMA Channel 0
36h
Reserved
37h
Test DMA Channel 1
38h
Reserved
39h
Test DMA page registers
3Ah
Reserved
3Bh
Reserved
3Ch
Test 8254
3Dh
Reserved
3Eh
Test 8259 interrupt mask bits for channel 1
3Fh
Reserved
40h
Test 8259 interrupt mask bits for channel 2
41h
Reserved
42h
Reserved
43h
Test 8259 functionality
44h
Reserved
45h
Reserved
46h
Reserved
47h
Initialize EISA slot
48h
Reserved
49h
1. Calculate total memory by testing the last double word of
each 64K page.
2. Program write allocation for AMD K5 CPU.
4Ah
Reserved
4Bh
Reserved
4Ch
Reserved
4Dh
Reserved
59
Checkpoint
Description
4Eh
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not identical.
4Fh
Reserved
50h
Initialize USB Keyboard & Mouse
51h
Reserved
52h
Test all memory (clear all extended memory to 0)
53h
Clear password according to H/W jumper (Optional)
54h
Reserved
55h
Display number of processors (multi-processor platform)
56h
Reserved
57h
1. Display PnP logo
2. Early ISA PnP initialization - Assign CSN to every ISA PnP
device
58h
Reserved
59h
Initialize the combined Trend Anti-Virus code
5Ah
Reserved
5Bh
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Ch
Reserved
5Dh
1. Initialize Init_Onboard_Super_IO
2. Initialize Init_Onboard_AUDIO
5Eh
Reserved
5Fh
Reserved
60h
Okay to enter Setup utility; i.e. not until this POST stage can
users enter the CMOS setup utility.
61h
Reserved
62h
Reserved
63h
Reset keyboard if Early_Reset_KB is not defined.
64h
Reserved
65h
Initialize PS/2 Mouse
66h
Reserved
67h
Prepare memory size information for function call:
INT 15h ax=E820h
60
68h
Reserved
69h
Turn on L2 cache
6Ah
Reserved
6Bh
Program chipset registers according to items described in Setup
& Auto-configuration table
6Ch
Reserved
Chapter 4
Checkpoint
Description
6Dh
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to “Auto”.
6Eh
Reserved
6Fh
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware
70h
Reserved
71h
Reserved
72h
Reserved
73h
Reserved
74h
Reserved
75h
Detech &install all IDE device: HDD, LS120, ZIP, CDROM...
76h
(Optional feature)
Enter AWDFLASH.EXE if:
- AWDFLASH.EXE is found in floppy drive.
- ALT+F2 is prrssed.
77h
Detect serial ports & parallel ports
78h
Reserved
79h
Reserved
7Ah
Detect & install co-processor
7Bh
Reserved
7Ch
Init HDD write protect
7Dh
Reserved
7Eh
Reserved
7Fh
Switch back to text mode if full screen logo is supported.
- If errors occur, report errors & wait for keys
- If no errors occur or F1 key is pressed to continue:
Clear EPA or customization logo.
Chapter 4
80h
Reserved
81h
Reserved
82h
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo).
3. If password is set, ask for password.
83h
Save all data in stack back to CMOS
84h
Initialize ISA PnP boot devices
85h
1. USB final initialization
2. Switch screen back to text mode
86h
Reserved
87h
NET PC: Build SYSID structure
88h
Reserved
89h
1. Assign IRQs to PCI devices.
2. Set up ACPI table at top of the memory.
8Ah
Reserved
61
Checkpoint
62
Description
8Bh
1. Invoke all ISA adapter ROMs
2. Invoke all PCI ROMs (except VGA)
8Ch
Reserved
8Dh
1. Enable/Disable Parity Check according to CMOS setup.
2. APM Initialization
8Eh
Reserved
8Fh
Clear noise if IRQs
90h
Reserved
91h
Reserved
92h
Reserved
93h
Read HDD boot sector information for Trend Anti-Virus code
94h
1.
2.
3.
4.
5.
6.
7.
8.
95h
Update keyboard LED & typematic rate
96h
1.
2.
3.
4.
5.
FFh
Boot attempt (INT 19h)
Enable L2 cache
Program Daylight Saving
Program boot up speed
Chipset final initialization
Power management final initialization
Clear screen & dispaly summary table
Program K6 write allocation
Program P6 class write combining
Build MP table
Build & update ESCD
Set CMOS century to 20h or 19h
Load CMOS time into DOS timer tick
Build MSIRQ routing table
Chapter 4
POST Error Messages List
If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error
Messages List” to diagnose system problems. If you did not receive any error message, look for a description
of your error symptoms in “Error Sympton List”.
NOTE: When you have deemed it necessary to replace an FRU, and have done so, you must run a total
system check to ensure that no other activity has been affected by the change. This system check can
be done through the diagnostics program.
NOTE: Check all power supply voltages, switch, and jumper settings before you replace the main board. Also
check the power supply voltages if you have a “system no-power” condition.
NOTE: To diagnose a problem, first find the BIOS error messages in the left column. If directed to a check
procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the
first Action/FRU listed in right column is the most likely cause.
BIOS Messages
Action/FRU
I/O Parity Error
1. System board
CPU Clock Mismatch
1. Enter BIOS Setup and load the default settings.
2. Ensure BIOS setting for processor is set
correctly.
Real Time Clock Error
CMOS Battery Bad
CMOS Checksum Error
1. Enter BIOS Setup and load the default settings.
2. RTC Battery.
3. System Board.
Equipment Configuration Error
1. Ensure the system configuration set in BIOS
Setup is correct.
2. Enter BIOS Setup and load the default settings.
3. RTC battery.
4. System board.
System Management Memory Bad
Memory Error at MMMM:SSSS:OOOOh
1. Insert the memory modules in the DIMM sockets
properly, then reboot the system.
2. Memory module.
3. System board.
RAM Parity Error
1. Enter BIOS Setup to disable parity check.
2. Memory module
3. System board
PS/2 Keyboard Error or Keyboard Not
Connected
PS/2 Keyboard Interface Error
PS/2 Keyboard Locked
1.
2.
3.
4.
5.
Onboard xxx... Conflict(s)
1. Enter BIOS Setup and load the default settings.
2. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
Floppy Disk Controller Error
Floppy Drive A Error
Floppy Drive B Error
1. Diskette drive cable/connection.
2. Diskette drive.
3. System board
On Board Parallel Port Conflict(s)
On Board Serial Port 1 Conflict(s)
On Board Serial Port 2 Conflict(s)
1. Enter BIOS Setup and load the default settings.
2. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
Chapter 4
Re-connect PS/2 keyboard and mouse.
Enter BIOS Setup and load the default settings.
PS/2 keyboard
PS/2 mouse
System board
63
BIOS Messages
64
Action/FRU
Floppy Drive(s) Write Protected
Hard Disk Drive(s) Write Protected
1. Ensure that the diskette drive is not set to [Write
Protected] in the Security Options in BIOS
Setup.
2. Load default settings in Setup.
IDE Drive 0 Error
IDE Drive 1 Error
IDE Drive 2 Error
IDE Drive 3 Error
1.
2.
3.
4.
5.
IRQ Setting Error
Expansion ROM Allocation Fail
I/O Resource Conflict(s)
Memory Resource Conflict(s)
1. Load default settings in Setup.
2. Enter BIOS Setup and set the Reset
Resource Assignments of the PnP/PCI
Options to Yes, then reboot the system.
3. Remove all adapter cards that are NOT factoryinstalled, then reboot the system
PCI Device Error
1. Load default settings in Setup.
2. Enter BIOS Setup and set the Reset
Resource Assignments of the PnP/PCI
Options to Yes, then reboot the system.
3. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
PS/2 Pointing Device Interface Error
PS/2 Pointing Device Error
1.
2.
3.
4.
5.
DMI Table Was Destroyed
1. Flash BIOS
Press “DEL” key to enter Setup or F1 key to
continue
1. Press DEL to enter Setup and reconfigure the
system.
Press ESC to turn off NMI, or any key to reboot
1. Press ESC to reject NMI error or press any other
key to reboot the system.
Insert system diskette and press ENTER key to
reboot
1. Insert a bootable disk into the floppy disk drive
or remove this disk if a hard disk is installed.
Enter BIOS Setup and load the default settings.
Check IDE drive jumper.
IDE hard disk drive power.
IDE hard disk drive cable/connection.
IDE hard disk drive.
Re-connect PS/2 keyboard and mouse.
Enter BIOS Setup and load the default settings.
PS/2 mouse
PS/2 keyboard
System board
Chapter 4
Error Symptoms List
NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure,
replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/
FRU listed in right column is the most likely cause
.
Error Symptom
Action/FRU
Processor / Processor Fan
NOTE: Normally, the processor fan should be operative, and the processor clock setting should be
exactly set to match its speed requirement before diagnosing any processor problems.
Processor fan does not run but power
supply fan runs.
1. Ensure the system is not in power saving mode. See
“Power Management” in chapter 2.
2. With the system power on, measure the voltage of
processor fan connector. Its reading should be +12Vdc.
3. System board.
Processor test failed.
1. Processor
2. System board
System Board and Memory
NOTE: Ensure the memory modules are installed properly and the contact leads are clean before
diagnosing any system problems.
Memory test failed.
1. See "Memory"
2. System board
Incorrect memory size shown or
repeated during POST.
1. Insert the memory modules in the DIMM sockets properly,
then reboot the system.
2. Memory module.
3. System board.
System works but fails to enter power
saving mode when the Power
Management Mode is set to Enabled,
and power saving timer set in BIOS has
elapsed.
1. Enter BIOS Setup and load default settings.
In Windows 98, check settings in Power Management
Property of Control Panel.
2. Reload software from Recovery CD.
System hangs before system boot.
1. See "Index of Symptoms"
2. See "Undetermined Problems"
System hangs after system boot.
1. Execute a system test and set it to stop at “Halt on Error”
to see the potential cause of the problem.
2. See “Undetermined Problems”.
Blinking cursor only; system does not
work.
1.
2.
3.
4.
Diskette/IDE drive connection/cables
Diskette/IDE disk drives
See “Undetermined Problems”.
System board
Diskette Drive
NOTE: Ensure the diskette drive is configured correctly in BIOS Setup and its read/write head is
clean before diagnosing any diskette drive problems.
Media and drive are mismatched.
Chapter 4
1. Ensure the diskette drive is configured correctly in the
Disk Drives of BIOS Setup.
2. Ensure the diskette drive is correctly formatted.
3. Diskette drive connection/cable
4. Diskette drive
5. System board
65
Error Symptom
Action/FRU
Diskette drive does not work.
1. Ensure the diskette drive is not set to None in the Disk
Drives of BIOS Setup.
2. Diskette drive power
3. Diskette drive connection/cable
4. Diskette drive
5. System board
Diskette drive read/write error.
1. Diskette.
2. Ensure the diskette drive is not set to Write protect
in the Security Options of BIOS Setup.
3. Diskette drive cable.
4. Diskette drive.
5. System board.
Diskette drive LED comes on for more
than 2 minutes when reading data.
1.
2.
3.
4.
Diskette
Diskette drive connection/cable
Diskette drive
System board
Diskette drive LED fails to light, and the
drive is unable to access for more than 2
minutes.
1.
2.
3.
4.
5.
Diskette
Diskette drive power
Diskette drive connection/cable
Diskette drive
System board
Diskette drive test failed.
1.
2.
3.
4.
Diskette
Diskette drive
Diskette drive cable
System board
Hard Disk Drive
NOTE: Ensure hard disk drive is configured correctly in BIOS Setup, cable/jumper are set correctly
before diagnosing any hard disk drive problems.
Hard disk drive test failed.
1.
2.
3.
4.
Enter BIOS Setup and Load default settings.
Hard disk drive cable.
Hard disk drive.
System board.
Hard disk drive cannot format
completely.
1.
2.
3.
4.
Enter BIOS Setup and Load default settings.
Hard disk drive cable.
Hard disk drive.
System board.
Hard disk drive has write error.
1. Enter BIOS Setup and Load default settings.
2. Hard disk drive.
Hard disk drive LED fails to light, but
system operates normally.
1. With the system power on, measure the voltage of hard
disk LED connector.
2. Hard drive LED cable.
CD/DVD-ROM Drive
NOTE: Ensure CD/DVD-ROM drive is configured correctly in BIOS Setup, cable/jumper are set
correctly and its laser beam is clean before diagnosing any CD/DVD-ROM drive problems.
CD/DVD-ROM drive LED doesn't come
on but works normally.
66
1. CD/DVD-ROM drive
Chapter 4
Error Symptom
CD/DVD-ROM drive LED flashes for
more than 30 seconds before LED
shutting off.
Action/FRU
1. CD/DVD-ROM may have dirt or foreign material on it.
Check with a known good disc.
2. CD/DVD-ROM is not inserted properly.
3. CD/DVD-ROM is damaged.
Software asks to reinstall disc.
Software displays a reading CD/DVD
error.
CD/DVD-ROM drive cannot load or eject
when the system is turned on and its
eject button is pressed and held.
1. Disconnect all cables from CD/DVD-ROM drive except
power cable, then press eject button to try to unload the
disk.
2. CD/DVD-ROM drive power.
3. CD/DVD-ROM drive
CD/DVD-ROM drive does not read and
there are no messages are displayed.
1. CD may have dirt or foreign material on it. Check with a
known good disc.
2. Ensure the CD/DVD-ROM driver is installed properly.
3. CD/DVD-ROM drive.
CD/DVD-ROM drive can play audio CD
but no sound output.
1. Ensure the headphone jack of the CD/DVD-ROM has an
output.
2. Turn up the sound volume.
3. Speaker power/connection/cable.
4. CD/DVD-ROM drive.
Real-Time Clock
Real-time clock is inaccurate.
1. Ensure the information in the Date and Time of BIOS
Setup is set correctly.
2. RTC battery.
3. System board
Audio software program invokes but no
sound comes from speakers.
1. Speaker power/connection/cable.
Audio
Modem
Modem ring cannot wake up system
from suspend mode.
1. Ensure the Modem Ring Indicator in BIOS Setup or
Power Management is set to Enabled.
2. If PCI modem card is used, reinsert the modem card to
PCI slot firmly or replace the modem card.
3. If ISA modem card is used, ensure the modem ring-in
cable from the modem card to system board is connected
properly.
4. In Win 98, ensure the telephone application is configured
correctly for your modem and set to receive messages
and/or fax.
Data/fax modem software program
invokes but cannot receive/send data/
fax
1. Ensure the modem card is installed properly.
Fax/voice modem software program
invokes but has no sound output. (Data
files are received normally; voice from
modem cannot be produced, but system
sound feature works normally.)
1. Ensure the modem voice-in cable from modem adapter
card to system board
Video and Monitor
Video memory test failed.
Video adapter failed.
Chapter 4
1. Remove all non-factory-installed cards.
2. Load default settings (if screen is readable).
3. System board
67
Error Symptom
68
Action/FRU
Display problem:
- Incorrect colors
No high intensity
Missing, broken, or incorrect characters
Blank monitor(dark)
Blank monitor(bright)
Distorted image
Unreadable monitor
Other monitor problems
1.
2.
3.
4.
Monitor signal connection/cable.
Monitor
Video adapter card
System board
Display changing colors.
1. Monitor signal connection/cable
2. Monitor
3. System board
Display problem not listed above
(including blank or illegible monitor).
1. “Monitor".
2. Load default settings (if screen is readable).
3. System board
Chapter 4
Error Symptom
Action/FRU
Parallel/Serial Ports
Execute “Load BIOS Default Settings” in BIOS Setup to confirm ports presence before diagnosing any
parallel/serial ports problems.
Serial or parallel port loop-back test
failed.
1. Make sure that the LPT# or COM# you test is the same
as the setting in BIOS Setup.
2. Loop-back.
3. System board.
Printing failed.
1. Ensure the printer driver is properly installed. Refer to the
printer service manual.
2. Printer.
3. Printer cable.
4. System board.
Printer problems.
1. Refer to the service manual for the printer.
Keyboard
Some or all keys on keyboard do not
work.
1. Keyboard
Power Supply
Pressing power switch does not turn off
system. (Only unplugging the power
cord from electrical outlet can turn off the
system.)
1. Ensure the Power Switch < 4 sec. in BIOS Setup of
Power Management is not set to Suspend.
2. Power switch cable assembly
Pressing power switch does not turn on
the system.
1. Ensure the power override switch (situated at the back of
the machine, just above the connector for the power
cable) is not set to OFF.
2. Power switch cable assembly.
Executing software shutdown from
Windows98 Start menu does not turn off
the system. (Only pressing power switch
can turn off the system).
1. Load default settings.
2. Reload software from Recovery CD.
No system power, or power supply fan is
not running.
1. Power Supply
2. System Board
Other Problems
Any other problems.
Chapter 4
1. Undetermined Problems
69
70
Chapter 4
Chapter 5
Jumper and Connector Information
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the mainboard.
Setting Jumpers
Use the mainboard jumpers to set system configuration options. Jumpers with more than one pir are
numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.
Jumper
Description
The illustrations below show a 2-pin
jumper. When the jumper cap is
placed on both pins, the jumper is
SHORT. If you remove the jumper
cap, or place the jumper cap on just
one pin, the jumper is OPEN.
Short
Open
This illustration shows a 3-pin
jumper. Pins1 and 2 are SHORT.
1 2
3
Chapter 5
71
Checking Jumper Settings
The following illustration shows the location of the mainboard jumpers. Pin 1 is labeled.
Jumper
Type
Description
JP1
3-pin
Clear CMOS
Setting (default)
1-2: Normal
2-3: Clear CMOS
JP1
1
JP3
2-pin
BIOS Protect
1-2: Write Enable
2-3: Write Disable
JP3
1
Jumper
72
Description
JP1 : Clear CMOS Jumper
This jumper is to clear the contents of CMOS memory. You may need
to clear the CMOS memory if the settings in the Setup Utility are
incorrect that prevents your mainboard from operating. To clear the
CMOS memory, disconnect all the power cables from the mainboard
and then move the jumper cap into the CLEAR setting for a few
seconds. This jumper enables you to reset BIOS.
JP3: BIOS Protect Jumper
This jumper enables you to prevent the BIOS from being updated
(flashed). Set the jumper to disabled if you are going to update your
BIOS. After updating the BIOS, return it to the default setting
(Enabled).
Chapter 5
Connecting Case Components
After you have installed the mainboard into a case, you can begin connecting the mainboard components.
Refer to the following:
Description
1.
Connect the CPU cooling
fan cable to CPUFAN1.
2.
Connect the case cooling
fan connector to
CASFAN1.
3.
Connect the Northbridge
cooling fna to NBFAN1.
4.
Connect the case LED
cable to SJ1. Connect the
case switches and
indicator LEDs to the
PANEL1.
5.
Connect the standard
power supply connector
to ATX1.
6.
Connect the Pentium 4
processor auxiliary case
power supply connector
to ATX2.
Connector
ATX1: ATX 20-pin Power Connector
Pin
Signal Name
Pin
Signal Name
1
+3.3V
11
+3.3V
2
+3.3V
12
-12V
3
Ground
13
Ground
4
+5V
14
PS NO#
5
Ground
15
Ground
6
+5V
16
Ground
7
Ground
17
Ground
8
PWRGD
18
+5V
9
+5VSB
19
+5V
10
+12V
20
+5V
ATX2: ATX12V Power Connector
Pin
Signal Name
1
+12V
2
+12V
3
Ground
4
Ground
Chapter 5
73
CPUFAN1/CASFAN1/NBFAN1: Fan Power Connectors
Pin
Signal Name
Function
1
GND
System Ground
2
+12V
Power +12V
3
Sense
Sensor
SJ1: Single Color LED Header
Pin
Signal Name
Function
1
ACPI LED
MSG LED(-) Green
2
ACPI LED
MSG LED(-) Green
3
SB5V
Power LED(+)
ACPI LED Function
Setting
74
Signal Name
Color
S0
Light
S1
Blinking
S3
Blinking
S4/S5
Dark
Chapter 5
Front Panel Connector
The front panel connect (PANEL 1) provides a standard set of switch and LED connectors commonly
found on ATX or micro-ATX cases. Refer to the table below for information:
Setting
Pin
Signal
Function
Pin
Signal
Function
1
HD_LED_P
Hard disk LED
([positive)
2
FP PWR/SLP
MSG LED(dual
color or single
color (+))
3
HD_LED_N
Hard disk active
LED (negative)
4
FP PWR/SLP
MSG LED( dual
color or single
color(-))
5
RST_SW_N
Reset Switch
6
PWR_SW_P
Power Switch
7
RST_SW_P
Reset Switch
8
PWR_SW_N
Power Switch
9
RSVD
Reserved
10
NC
No Pin
Function
Description
Hard Disk Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual
indication that data is being read from or written to the hard drive. For
the LED to function properly, an IDE drive should be connected to the
onboard IDE interface. The LED will also show activity for devices
connected to the SCSI ( hard drive activity LED ) connector.
Power/Sleep/ Message Waiting
LED
Connecting pis 2 and 4 to a signal- or dual-color, front panel mounted
LED provides power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pins 5 and 7 to a
momentary-contact switch that is normally open. When the switch is
closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8
to a momentary-contact switch that is normally open. The switch
should maintain contact for at least 50ms to signal the power supply to
switch on or off. The time requirement is due to internal debounce
circuitry. After receiving a power on/off signal, at lease two seconds
elapses before the power supply recognizes another on/off signal.
Chapter 5
75
Connecting Optional Devices
Refer to the following for information on connecting the mainboard’s optional devices:
AUDIO1: Front Panel Audio Connector
This connector allows the user to install auxiliary front-oriented microphone and line-out ports for easier
access.
Pin
76
Signal Name
Function
1
AUD_MIC
Front Panel Microphone input signal
2
AUD_GND
Ground used by Analog Audio Circuits
3
AUD_MIC_BIAS
Microphone Power
4
AUD_VCC
Filtered +5V used by Analog Audio Circuits
5
AUD_FPOUT_R
Right Channel Audio signal to Front Panel
6
AUD_RET_R
Right Channel Audio signal to Return from
Front Panel
7
HP_ON
Reserved for future use to control Headphone Amplifier
8
KEY
No Pin
9
AUD_FPOUT_L
Left Channel Audio signal to Front Panel
10
AUD_RET_L
Left Channel Audio Signal to Return from
Front Panel
Chapter 5
SPDIFO1: SPDIF out header (optional)
You can purchase an optional 24-bit digital audio extension bracket from a third-party vendor. You can
use the audio RCA jacks to connect to digital audio devices. If your CD-ROM/DVD drive has digital audio
output, you can connect it to the input pins of the SPDIF connector.
Pin
Singal Name
Function
1
SPDIF
SPDIF digital output
2
+5VA
5V analog power
3
NC
Not Connector
4
GND
Ground
AUXIN1:Auxiliary-in Header
This connector is an additional line-in audio connector. It allows you to attach a line-in cable when your
rear line-in jack is set as line out port for 4-channel function.
Pin
Signal Name
Function
1
AUX_L
AUX in left channel
2
GND
Ground
3
GND
Ground
4
AUX_R
AUX in right channel
SATA1/SATA2: Serial ATA Headers
These connectors are use to support the new Serial ATA devices for the highest date transfer rates
(150 MB/s), simpler disk drive cabling and easier PC assembly.It eliminates limitations of the current
Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
Pin
Signal Name
Pin
2
Signal Name
1
GND
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
-
-
1394A2: IEEE 1394a Header
Use this header to connect to any IEEE 1394a interface.
Pin
Signal Name
Pin
Signal Name
1
TPA+
2
TPA-
3
GND
4
GND
5
TPB+
6
TPB-
7
Cable-Power
8
Cable-Power
9
NC
10
GND
Chapter 5
77
USB3/USB4: Front Panel USB Connectors
The mainboard has two USB ports installed on the rear edge I/O port array. Additionally, some computer
cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector
to connect the front mounted ports to the mainboard.
Pin
Signal Name
Function
1
VREG_FP_USBPWR0
Front Panel USB Power
2
VREG_FP_USBPWR0
Front Panel USB Power
3
USB_FP_P0-
USB Port 0 Negative Signal
4
USB_FP_P1-
USB Port 1 Negative Signal
5
USB_FP_P0+
USB Port 0 Positive Signal
6
USB_FP_P1+
USB Port 1Positive Signal
7
GND
Ground
8
GND
Ground
9
KEY
No Pin
10
USB_FP_OC0
Overcurrent Signal
NOTE: Please make sure that the USB cable has the same pin assignement as indicated above. A
different pin assignment may cause damage or system hang-up.
COM2: Onboard Serial Port Connector
Connect a serial port extension bracket to this header to add a second serial port to your system.
Pin
78
Singal Name
Function
1
NDCDB
Data Carry Detect
2
NSINB
Serial Data In
3
NSOUTB
Serial Data Out
4
NDTRB
Data Terminal Ready
5
GND
Ground
6
NDSRB
Data Set Ready
7
NRTSB
Request to Send
8
NCTSB
Clear to Send
9
NRIB
Ring Indicator
10
Key
Key
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of
AcerPower F1 / Aspire T310. Refer to this chapter whenever ordering for parts to repair or for RMA (Return
Merchandise Authorization).
Chapter 6
79
AcerPower F1 / Aspire T310 Exploded Diagram
80
Chapter 6
NOTE: Due to the Aspire T310 (new black bezel) is smiliar with AcerPower F1 (white bezel); meanwhile, you
will see some parts which are the same.
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/, if you do not own a specific
account, you can still access the system with guest; guest). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list
of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to
order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to
return it.
AcerPower F1
Picture
Partname
Part No.
Memory
DDR266 256MB 0.14U 32MX8*8 NANYA NT256D64S88B0G-75B
DDR266 512MB 0.14U 32MX8*16 NANYA NT512D64S8HB0G-75B
DDR333 256MB INFENION
DDR333 128MB 0.14U 16M*16*4 NANYA NT128D64SH4B1G-6K
DDR333 256MB 0.14U 32M*8*8 NANYA NT256D64S88B1G-6K
DDR333 512MB 0.14U 32M*8*16 NANYA NT512D64S8HB1G-6K
DDR333 256MB MICRON MT8VDDT3264AG-335CA CL2.5
DDR400 128MB INFINEON HYS64D16301GU-5-B
DDR400 256MB INFINEON HYS64D32300GU-5-B
DDR400 512MB INFINEON HYS64D64320GU-5-B
DDR400 256MB NANYA NT256D64S88B1G-5T EA
DDR400 512MB NANYA
KN.25603.012
KN.51203.008
KN.25602.002
KN.12803.005
KN.25603.008
KN.51203.004
KN.25604.008
KN.12802.005
KN.25602.008
KN.51202.006
KN.25603.011
TBD
CELERON 2.4GHZ/400FSB/128K
CELERON 2.6GHZ/400FSB/128K (MULTIPLE VID)
NORTHWOOD 2.6GHZ/128K/400FSB
NORTHWOOD 2.4GHZ/512K/533FSB
NORTHWOOD 2.8GHZ/512K/533FSB
NORTHWOOD 2.4GHZ/512K/800FSB
NORTHWOOD 2.6GHZ/512K/800FSB
NORTHWOOD 2.8GHZ/512K/800FSB
NORTHWOOD 3.0GHZ/512K/800FSB
KC.DCD01.24A
KC.DCD01.26A
KC.DPD01.26A
KC.DPD01.24B
KC.DPD01.28B
KC.DP001.24C
KC.DP001.26C
KC.DP001.28C
KC.DP001.30C
FDD 1.44MB PANASONIC JU-256A048P WHITE
KF.25602.002
CPU/PROCESSOR
FDD/Floppy Disk Drive
Chapter 6
81
AcerPower F1
Picture
Partname
Part No.
HDD/Hard Disk Drive
HDDPROTEGE 40G 5400RPM, ATA-100 WD WD400EB-42CPF0
HDD 80G 5400RPM, ATA-100 WD WD800EB-00DJF0
HDD C2 40G 5400 RPM, ATA-100 SEAGATE ST340015A
HDD U9 80G 5400 RPM, ATA-100 SEAGATE ST380012A
HDD ALPINE 80G 7200RPM, ATA-100 SEAGATE ST380011A
HDD ALPINE 120G 7200RPM, ATA-100 SEAGATE ST3120022A
HDD XL40S 40G 7200RPM, ATA-100 WD 400BB-00DEA0
HDD XL80S 80G 7200RPM WD WD800BB-00DKA0
HDD XL80 120G 7200RPM WD 1200BB-00DWA0
HDD 40G 7200RPM, ATA-100 HITACHI HDS722540VLAT20
HDD 80G 7200RPM, ATA-100 HITACHI HDS722580VLAT20
HDD 120G 7200RPM, ATA-100 HITACHI HDS7225120VLAT20
KH.04008.004
KH.08008.004
KH.04001.002
KH.08001.002
KH.08001.001
KH.12001.001
KH.04008.002
KH.08008.003
KH.12008.001
KH.04007.007
KH.08007.005
KH.12007.003
CD-ROM/DVD-ROM/CD-RW
CD-ROM DRIVE 52X BTC F564E WHITE
CD-ROM DRIVE 52X MSI MS-8152 WHITE
KD.52X0A.002
KD.0520B.002
CD-RW DRIVE 52X24X52X LITE-ON LTR-52246S WHITE
KR.52X01.001
DVD-ROM DRIVE 16X PIONEER DVD-121CHF WHITE
DVD-ROM DRIVE 16X PIONEER DVD-121RD WHITE
DVD-ROM DRIVE 16X LITI-ON XJ-HD166S WHITE
DVD-ROM DRIVE 16X HLDS GCR-8162B WHITE
KV.01605.002
KV.16X05.003
KV.16X04.002
TBD
COMBO DRIVE 48X HLDS GCC-4480B WHITE
KO.48X0A.001
DVD DUAL DRIVE 4X NEC ND-1300A WHITE
DVD DUAL DRIVE 4X PIONEER DVR-106RD WHITE
KU.0040B.001
KU.00405.002
SUPERMULTI PLUS 4X DVD HLDS GSA-4040B WHITE
KU.0040C.001
IDE HDD CABLE ATA66 40PIN
50.PSPVF.001
IDE CD-ROM CABLE ATA66 40PIN
50.PSPVF.002
IDE FDD CABLE 34PIN
50.PSPVF.003
Cables
82
Chapter 6
AcerPower F1
Picture
Partname
Part No.
AUDIO CABLE 8PIN 2CON
50.S03VF.001
FRONT INTERNAL USB CABLE
50.S03VF.002
MB E61ML P4/661FX/964L/2DIMM/3PCI
MB.S0307.001
VGA CARD ATI RADEON 9200 (8X) 64MB DDR W/ TV
OUT(NTSC), ATX BRACKET FIC
VGA CARD ATI RADEON 9200 (8X) 64MB DDR W/ TV OUT(PAL),
ATX BRACKET FIC
VGA CARD ATI RADEON 9600 128MB DDR W/ TV OUT + DVI
(PAL), ATX BRACKET FIC A96
VGA CARD ATI RADEON 9600 128MB DDR W/ TV + DVI OUT
(NTSC), ATX BRACKET FIC A96
VGA CARD XABRE200 AGP 8X 32MB, ATX BRACKET
VG.A9207.001
MODEM CARD 56K F-1156I(+)/R12 ATX GVC-AAP
MODEM CARD 56K F-1156I(+)/R12 PACIFIC ATX GVC-USA
MODEM CARD 56K F-1156I(+)/R12 GVC-AUSTRALIA
FX.56I02.003
FX.56I02.001
FX.56102.005
USB/ AUDIO DAUGHTER BOARD FOXCONN
55.PSPVF.001
POWER SUPPLY 230W W/O PFC FSP FSP200-ATV(A)
POWER SUPPLY 230W W PFC FSP 200-ATV(A)(PF)
PY.23008.003
PY.23008.004
Main board
Boards/Cards
VG.A9207.002
VG.A9607.001
VG.A9607.002
VG.20005.001
Power Supply
Case/Cover/Bracket Assembly
Chapter 6
FRONT BEZEL W/ POWER BUTTON, 5.25" 3.5" EMPTY COVER,
USB DOOR
60.P01VF.001
POWER BUTTON
42.PSPVF.001
SIDE DOOR
60.PSPVF.002
CHASSIS W/ I/O BRACKET
60.P01VF.002
I/O BRACKET
33.S03VF.001
RETENTION MODULE
TBD
LED MODULE
42.P01VF.001
83
AcerPower F1
Picture
Partname
Part No.
EMPTY COVER FOR 5.25" DEVICE
42.PSPVF.005
HDD BRACKET
33.PSPVF.002
FILLER COVER FOR 3.5" DEVICE
42.PSPVF.007
MOUSE PS2 2 BUTTON+WHEEL KYE POWER SCROLL PS2
WHITE
OPTICAL MOUSE USB 2 BUTTON+WHEEL WHITE
MS.PSE04.003
PS/2 KEYBOARD, KBP2971, US VER., 104KEYS
PS/2 KEYBOARD, KBP2971, T.CHINESE VER., 104KEYS
PS/2 KEYBOARD, KBP2971, ARABIC VER., 104KEYS
PS/2 KEYBOARD, KBP2971, THAI VER., 104KEYS
PS/2 KEYBOARD, KBP2971, SPANISH/US VER., 105KEYS
PS/2 KEYBOARD, KBP2971, INT'L US VER., 104KEYS
PS/2 KEYBOARD, KBP2971, CANADIAN/FRENCH VER, 105KEYS
PS/2 KEYBOARD, KBP2971, BRAZILIAN VER., 107KEYS
PS/2 KEYBOARD, KBP2971, UK VER., 104KEYS
PS/2 KEYBOARD, KBP2971, FRENCH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, GERMANY VER., 105KEYS
PS/2 KEYBOARD, KBP2971, ITALIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SWISS VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SWEDEN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, BELGIUM VER., 105KEYS
PS/2 KEYBOARD, KBP2971, DUTCH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, HOLLAND VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SPANISH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, PORTUGESE VER., 105KEYS
PS/2 KEYBOARD, KBP2971, ICELAND VER., 105KEYS
PS/2 KEYBOARD, KBP2971, NORWEGIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, HEBREW VER., 105KEYS
PS/2 KEYBOARD, KBP2971, POLISH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SLOVENIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SLOVAKIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, TURKEY VER., 105KEYS
PS/2 KEYBOARD, KBP2971, RUSSIAMVER., 104KEYS
PS/2 KEYBOARD, KBP2971, HUNGARIA VER., 105KEYS
PS/2 KEYBOARD, KBP2971, GREEK VER., 104KEYS
KB.KBP03.003
KB.KBP03.010
KB.KBP03.008
KB.KBP03.005
KB.KBP03.025
KB.KBP03.006
KB.KBP03.028
KB.KBP03.032
KB.KBP03.027
KB.KBP03.013
KB.KBP03.014
KB.KBP03.012
KB.KBP03.002
KB.KBP03.029
KB.KBP03.009
TBD
KB.KBP03.021
KB.KBP03.025
KB.KBP03.022
KB.KBP03.019
KB.KBP03.020
KB.KBP03.015
KB.KBP03.016
KB.KBP03.017
KB.KBP03.018
KB.KBP03.023
KB.KBP03.024
KB.KBP03.030
KB.KBP03.031
Peripheral
84
MS.PSE04.001
Chapter 6
AcerPower F1
Picture
Partname
Part No.
USB Keyboard, KU0355, US Ver., 104keys
USB Keyboard, KU0355, T.Chinese Ver., 104keys
USB Keyboard, KU0355, Arabic Ver., 104keys
USB Keyboard, KU0355, Thai Ver., 104keys
USB Keyboard, KU0355, Spanish/US Ver., 105keys
USB Keyboard, KU0355, Int'l US Ver., 104keys
USB Keyboard, KU0355, Canadian/French Ver., 105keys
USB Keyboard, KU0355, Brazilian Ver., 107keys
USB Keyboard, KU0355, UK Ver., 104keys
USB Keyboard, KU0355, French Ver., 105keys
USB Keyboard, KU0355, Germany Ver., 105keys
USB Keyboard, KU0355, Italian Ver., 105keys
USB Keyboard, KU0355, Swiss Ver., 105keys
USB Keyboard, KU0355, Swedish Ver., 105keys
USB Keyboard, KU0355, Belgium Ver., 105keys
USB Keyboard, KU0355, Dutch Ver., 105keys
USB Keyboard, KU0355, Holland Ver., 105keys
USB Keyboard, KU0355, Spanish Ver., 105keys
USB Keyboard, KU0355, Portugese Ver., 105keys
USB Keyboard, KU0355, Iceland Ver., 105keys
USB Keyboard, KU0355, Norwegian Ver., 105keys
USB Keyboard, KU0355, Hebrew Ver., 105keys
USB Keyboard, KU0355, Polish Ver., 105keys
USB Keyboard, KU0355, Slovenian Ver., 105keys
USB Keyboard, KU0355, Slovakian Ver., 105keys
USB Keyboard, KU0355, Turkey Ver., 105keys
USB Keyboard, KU0355, RussiamVer., 104keys
USB Keyboard, KU0355, Hungaria Ver., 105keys
USB Keyboard, KU0355, Greek Ver., 104keys
KB.KUP03.002
KB.KUP03.003
KB.KUP03.008
KB.KUP03.005
KB.KUP03.004
KB.KUP03.006
KB.KUP03.028
KB.KUP03.032
KB.KUP03.027
KB.KUP03.013
KB.KUP03.014
KB.KUP03.012
KB.KUP03.001
KB.KUP03.029
KB.KUP03.009
KB.KUP03.021
KB.KUP03.025
KB.KUP03.022
KB.KUP03.019
KB.KUP03.020
KB.KUP03.015
KB.KUP03.016
KB.KUP03.017
KB.KUP03.018
KB.KUP03.023
KB.KUP03.024
KB.KUP03.030
KB.KUP03.031
KB.KUP03.034
SPEAKER USB 3" *2 NEOSONICA THYME510 WHITE
SP.51004.001
CPU FANSINK P4 478 2.8G (AND BELOW) FOXCONN
PKP111G01D32 W/ LATCH
CPU FANSINK P4 478 FOR 3.0GHZ CPU (AND ABOVE)
FOXCONN PKP159GB1D22 + 92X92X25
HI.1110B.001
RUBBER FOOT
47.P01VF.001
M/B, USB BOARD SCREW
86.PSPVF.001
FDD, CD-ROM SCREW
86.PSPVF.002
CHASSIS SCREW
86.PSPVF.003
SPS SCREW
86.PSPVF.004
Speaker
Fansink
TBD
Foot Stand
Screws
Chapter 6
85
Aspire T310
Picture
Partname
Part No.
Memory
DDR266 256MB 0.14U 32MX8*8 NANYA NT256D64S88B0G-75B
DDR266 512MB 0.14U 32MX8*16 NANYA NT512D64S8HB0G-75B
DDR333 256MB INFENION
DDR333 128MB 0.14U 16M*16*4 NANYA NT128D64SH4B1G-6K
DDR333 256MB 0.14U 32M*8*8 NANYA NT256D64S88B1G-6K
DDR333 512MB 0.14U 32M*8*16 NANYA NT512D64S8HB1G-6K
DDR333 256MB MICRON MT8VDDT3264AG-335CA CL2.5
DDR400 128MB INFINEON HYS64D16301GU-5-B
DDR400 256MB INFINEON HYS64D32300GU-5-B
DDR400 512MB INFINEON HYS64D64320GU-5-B
DDR400 256MB NANYA NT256D64S88B1G-5T EA
DDR400 512MB NANYA
KN.25603.012
KN.51203.008
KN.25602.002
KN.12803.005
KN.25603.008
KN.51203.004
KN.25604.008
KN.12802.005
KN.25602.008
KN.51202.006
KN.25603.011
TBD
CELERON 2.4GHZ/400FSB/128K
CELERON 2.6GHZ/400FSB/128K (MULTIPLE VID)
NORTHWOOD 2.6GHZ/128K/400FSB
NORTHWOOD 2.4GHZ/512K/533FSB
NORTHWOOD 2.8GHZ/512K/533FSB
NORTHWOOD 2.4GHZ/512K/800FSB
NORTHWOOD 2.6GHZ/512K/800FSB
NORTHWOOD 2.8GHZ/512K/800FSB
NORTHWOOD 3.0GHZ/512K/800FSB
KC.DCD01.24A
KC.DCD01.26A
KC.DPD01.26A
KC.DPD01.24B
KC.DPD01.28B
KC.DP001.24C
KC.DP001.26C
KC.DP001.28C
KC.DP001.30C
FDD 1.44MB PANASONIC JU-256A048P BLACK
TBD
HDDPROTEGE 40G 5400RPM, ATA-100 WD WD400EB-42CPF0
HDD 80G 5400RPM, ATA-100 WD WD800EB-00DJF0
HDD C2 40G 5400 RPM, ATA-100 SEAGATE ST340015A
HDD U9 80G 5400 RPM, ATA-100 SEAGATE ST380012A
HDD ALPINE 80G 7200RPM, ATA-100 SEAGATE ST380011A
HDD ALPINE 120G 7200RPM, ATA-100 SEAGATE ST3120022A
HDD XL40S 40G 7200RPM, ATA-100 WD 400BB-00DEA0
HDD XL80S 80G 7200RPM WD WD800BB-00DKA0
HDD XL80 120G 7200RPM WD 1200BB-00DWA0
HDD 40G 7200RPM, ATA-100 HITACHI HDS722540VLAT20
HDD 80G 7200RPM, ATA-100 HITACHI HDS722580VLAT20
HDD 120G 7200RPM, ATA-100 HITACHI HDS7225120VLAT20
KH.04008.004
KH.08008.004
KH.04001.002
KH.08001.002
KH.08001.001
KH.12001.001
KH.04008.002
KH.08008.003
KH.12008.001
KH.04007.007
KH.08007.005
KH.12007.003
CPU/PROCESSOR
FDD/Floppy Disk Drive
HDD/Hard Disk Drive
CD-ROM/DVD-ROM/CD-RW
86
Chapter 6
Aspire T310
Picture
Partname
Part No.
CD-ROM DRIVE 52X BTC F564E BLACK
CD-ROM DRIVE 52X MSI MS-8152 BLACK
KD.0520A.001
KD.0520B.003
CD-RW DRIVE 52X24X52X LITE-ON LTR-52246S BLACK
KR.05201.001
DVD-ROM DRIVE 16X PIONEER DVD-121CHF BLACK
DVD-ROM DRIVE 16X PIONEER DVD-121RD BLACK
DVD-ROM DRIVE 16X LITI-ON XJ-HD166S BLACK
DVD-ROM DRIVE 16X HLDS GCR-8162B BLACK
TBD
KV.01605.003
TBD
KV.0160D.001
COMBO DRIVE 48X HLDS GCC-4480B BLACK
KO.0480A.001
DVD DUAL DRIVE 4X NEC ND-1300A BLACK
DVD DUAL DRIVE 4X PIONEER DVR-106RD BLACK
TBD
KU.00405.009
SUPERMULTI PLUS 4X DVD HLDS GSA-4040B BLACK
KU.0040D.007
IDE HDD CABLE ATA66 40PIN
50.PSPVF.001
IDE CD-ROM CABLE ATA66 40PIN
50.PSPVF.002
IDE FDD CABLE 34PIN
50.PSPVF.003
AUDIO CABLE 8PIN 2CON
50.S03VF.001
FRONT INTERNAL USB CABLE
50.S03VF.002
MB E61ML P4/661FX/964L/2DIMM/3PCI
MB.S0307.001
Cables
Main board
Boards/Cards
Chapter 6
87
Aspire T310
Picture
Partname
Part No.
VGA CARD ATI RADEON 9200 (8X) 64MB DDR W/ TV
OUT(NTSC), ATX BRACKET FIC
VGA CARD ATI RADEON 9200 (8X) 64MB DDR W/ TV OUT(PAL),
ATX BRACKET FIC
VGA CARD ATI RADEON 9600 128MB DDR W/ TV OUT + DVI
(PAL), ATX BRACKET FIC A96
VGA CARD ATI RADEON 9600 128MB DDR W/ TV + DVI OUT
(NTSC), ATX BRACKET FIC A96
VGA CARD XABRE200 AGP 8X 32MB, ATX BRACKET
VG.A9207.001
MODEM CARD 56K F-1156I(+)/R12 ATX GVC-AAP
MODEM CARD 56K F-1156I(+)/R12 PACIFIC ATX GVC-USA
MODEM CARD 56K F-1156I(+)/R12 GVC-AUSTRALIA
FX.56I02.003
FX.56I02.001
FX.56102.005
USB/ AUDIO DAUGHTER BOARD FOXCONN
55.PSPVF.001
POWER SUPPLY 230W W/O PFC FSP FSP200-ATV(A)
POWER SUPPLY 230W W PFC FSP 200-ATV(A)(PF)
PY.23008.003
PY.23008.004
VG.A9207.002
VG.A9607.001
VG.A9607.002
VG.20005.001
Power Supply
Case/Cover/Bracket Assembly
FRONT BEZEL W/ POWER BUTTON, 5.25" 3.5" EMPTY COVER,
USB DOOR
60.S03VF.001
POWER BUTTON
42.S03VF.001
SIDE DOOR
60.S03VF.002
CHASSIS W/ I/O BRACKET
60.S03VF.003
I/O BRACKET
33.S03VF.001
RETENTION MODULE
TBD
LED MODULE
42.S03VF.002
SWITCH HOLDER ASSY
42.S03VF.003
EMPTY COVER FOR 5.25" DEVICE
42.S03VF.004
HDD BRACKET
33.PSPVF.002
FILLER COVER FOR 3.5" DEVICE
42.S03VF.005
Peripheral
88
Chapter 6
Aspire T310
Picture
Chapter 6
Partname
Part No.
MOUSE PS2 2 BUTTON+WHEEL KYE POWERSCROLL PS2
BLACK
OPTICAL MOUSE USB 2 BUTTON+WHEEL KYE
POWERSCROLL USB SILVER
MS.PSE04.006
PS/2 Keyboard, KBP2971, US Ver., 104keys
PS/2 Keyboard, KBP2971, T.Chinese Ver., 104keys
PS/2 Keyboard, KBP2971, Thai Ver., 104keys
PS/2 Keyboard, KBP2971, Arabic Ver., 104keys
PS/2 Keyboard, KBP2971, Spanish/US Ver., 105keys
PS/2 Keyboard, KBP2971, Int'l US Ver., 104keys
PS/2 Keyboard, KBP2971, Canadian/French Ver., 105keys
PS/2 Keyboard, KBP2971, Brazilian Ver., 107keys
PS/2 Keyboard, KBP2971, UK Ver., 104keys
PS/2 Keyboard, KBP2971, French Ver., 105keys
PS/2 Keyboard, KBP2971, Germany Ver., 105keys
PS/2 Keyboard, KBP2971, Italian Ver., 105keys
PS/2 Keyboard, KBP2971, Swiss Ver., 105keys
PS/2 Keyboard, KBP2971, Swedish Ver., 105keys
PS/2 Keyboard, KBP2971, Belgium Ver., 105keys
PS/2 Keyboard, KBP2971, Dutch Ver., 105keys
PS/2 Keyboard, KBP2971, Holland Ver., 105keys
PS/2 Keyboard, KBP2971, Spanish Ver., 105keys
PS/2 Keyboard, KBP2971, Portugese Ver., 105keys
PS/2 Keyboard, KBP2971, Iceland Ver., 105keys
PS/2 Keyboard, KBP2971, Norwegian Ver., 105keys
PS/2 Keyboard, KBP2971, Hebrew Ver., 105keys
PS/2 Keyboard, KBP2971, Polish Ver., 105keys
PS/2 Keyboard, KBP2971, Slovenian Ver., 105keys
PS/2 Keyboard, KBP2971, Slovakian Ver., 105keys
PS/2 Keyboard, KBP2971, Turkey Ver., 105keys
PS/2 Keyboard, KBP2971, RussiamVer., 104keys
PS/2 Keyboard, KBP2971, Hungaria Ver., 105keys
PS/2 Keyboard, KBP2971, Greek Ver., 104keys
KB.KBP03.066
KB.KBP03.067
KB.KBP03.069
KB.KBP03.068
KB.KBP03.070
KB.KBP03.071
KB.KBP03.072
KB.KBP03.073
KB.KBP03.074
KB.KBP03.075
KB.KBP03.076
KB.KBP03.077
KB.KBP03.078
KB.KBP03.079
KB.KBP03.080
KB.KBP03.081
KB.KBP03.082
KB.KBP03.083
KB.KBP03.084
KB.KBP03.085
KB.KBP03.086
KB.KBP03.087
KB.KBP03.088
KB.KBP03.089
KB.KBP03.090
KB.KBP03.091
KB.KBP03.092
KB.KBP03.093
KB.KBP03.094
MS.PSE04.005
89
Aspire T310
Picture
Partname
Part No.
USB Keyboard, KU0355, Canadian/French Ver., 105keys
USB Keyboard, KU0355, US Ver., 104keys
USB Keyboard, KU0355, T.Chinese Ver., 104keys
USB Keyboard, KU0355, Arabic Ver., 104keys
USB Keyboard, KU0355, Thai Ver., 104keys
USB Keyboard, KU0355, Thai Ver., 104keys
USB Keyboard, KU0355, Spanish/US Ver., 105keys
USB Keyboard, KU0355, Int'l US Ver., 104keys
USB Keyboard, KU0355, Brazilian Ver., 107keys
USB Keyboard, KU0355, UK Ver., 104keys
USB Keyboard, KU0355, French Ver., 105keys
USB Keyboard, KU0355, Germany Ver., 105keys
USB Keyboard, KU0355, Italian Ver., 105keys
USB Keyboard, KU0355, Swiss Ver., 105keys
USB Keyboard, KU0355, Sweden Ver., 105keys
USB Keyboard, KU0355, Belgium Ver., 105keys
USB Keyboard, KU0355, Dutch Ver., 105keys
USB Keyboard, KU0355, Holland Ver., 105keys
USB Keyboard, KU0355, Spanish Ver., 105keys
USB Keyboard, KU0355, Portugese Ver., 105keys
USB Keyboard, KU0355, Iceland Ver., 105keys
USB Keyboard, KU0355, Norwegian Ver., 105keys
USB Keyboard, KU0355, Hebrew Ver., 105keys
USB Keyboard, KU0355, Polish Ver., 105keys
USB Keyboard, KU0355, Slovenian Ver., 105keys
USB Keyboard, KU0355, Slovakian Ver., 105keys
USB Keyboard, KU0355, Turkey Ver., 105keys
USB Keyboard, KU0355, RussiamVer., 104keys
USB Keyboard, KU0355, Hungaria Ver., 105keys
USB Keyboard, KU0355, Greek Ver., 104keys
KB.KUS03.010
KB.KUP03.034
KB.KUP03.035
KB.KUP03.037
KB.KUP03.038
KB.KUS03.008
KB.KUP03.036
KB.KUS03.009
KB.KUS03.001
KB.KUP03.041
KB.KUP03.039
KB.KUP03.040
KB.KUS03.011
KB.KUP03.042
KB.KUS03.012
KB.KUS03.003
KB.KUS03.013
KB.KUS03.002
KB.KUS03.004
KB.KUS03.004
KB.KUS03.014
KB.KUS03.015
KB.KUS03.016
KB.KUS03.017
KB.KUS03.018
KB.KUS03.019
KB.KUS03.020
KB.KUS03.021
KB.KUS03.022
KB.KUS03.023
SPEAKER USB 3" *2 NEOSONICA THYME510 BLACK
SP.51004.003
CPU FANSINK P4 478 2.8G (AND BELOW) FOXCONN
PKP111G01D32 W/ LATCH
CPU FANSINK P4 478 FOR 3.0GHZ CPU (AND ABOVE)
FOXCONN PKP159GB1D22 + 92X92X25
HI.1110B.001
RUBBER FOOT
47.S03VF.001
M/B, USB BOARD SCREW
86.PSPVF.001
FDD, CD-ROM SCREW
86.PSPVF.002
CHASSIS SCREW
86.S03VF.001
SPS SCREW
86.PSPVF.004
Speaker
Fansink
TBD
Foot Stand
Screws
90
Chapter 6
Appendix A
Model Definition and Configuration
The AcerPower F1 / Aspire T310 Model No. Define:
1.
Trade Mark:
2.
Brand Name: Acer
3.
Description: Intel Pentium4/Celeron Processor
4.
Product Name: AcerPower F1 / Aspire T310
Appendix A
91
92
Appendix A
Appendix B
Test Compatible Components
AcerPower F1 / Aspire T310 compatibility is tested and verified by Acer’s internal testing department. All of its
system
functions are tested under the environments of Windows XP Home.
Appendix B
93
Microsoft Windows XP Home Environment Test
Components
Specifications
Model Description
Main Board
Foxconn
P4/661FX/964L/2DIMM/3PCI
E61ML
P4/661FX/964L/2DIMM/3PCI, with 1394
E61ML-2
Celeron 2.4GHz/400FSB/128K
SL6VU, RK80532RC056128
CPU
Intel
Celeron 2.5GHz/400FSB/128K
Celeron 2.6GHz/400FSB/128K (Multiple
VID)
SL6V3, RK80532RC064128
Celeron 2.8GHz/400FSB/128K
P4 2.5Ghz/400FSB/512K
Northwood 2.4Ghz/512k/533FSB
SL6PC, RK80532PE056512
Northwood 2.8Ghz/512k/533FSB
SL6PF, RK80532PE072512
Northwood 2.4G Socket 478
Northwood 2.4Ghz/512k/800FSB
Northwood 2.6G Socket 478
Northwood 2.6Ghz/512k/800FSB
Northwood 2.8G Socket 478
Northwood 2.8Ghz/512k/800FSB
Northwood 3.0G Socket 478
Northwood 3.0Ghz/512k/800FSB
Northwood 3.2G Socket 478
Northwood 3.2Ghz/512k/800FSB
DDR 266 256MB 0.14u 32MX8*8
HYS64D32000GU-7-B
DIMM (DDR 266/333/400)
Infineon
Nanya
Micron
DDR 400 128MB
HYS64D16301GU-5-B
DDR 400 256MB
HYS64D32300GU-5-B
DDR 266 256MB 0.14u 32Mx8*8
NT256D64S88B0G-75B
DDR 266 512MB 0.14u 32Mx8*16
NT512D64S8HB0G-75B
DDR 333 128MB 0.14u 16M*16*4
NT128D64SH4B1G-6K
DDR 333 256MB 0.14u 32M*8*8
NT256D64S88B1G-6K
DDR 333 512MB 0.14u 32M*8*16
NT512D64S8HB1G-6K
DDR 400 256MB
NT256D64S88B1G-5T EA
DDR 400 512MB
NT512D64S8HB1G-5T
DDR 333 256MB
MT8VDDT3264AG-335CA CL2.5
HDD (5400RPM/7200RPM)
WD
Seagate
94
Protege 40G 5400RPM, ATA-100
WD400EB-42CPF0
WD 80G 5400RPM, ATA-100
WD800EB-00DJF0
XL40S 40G 7200RPM, ATA-100
400BB-00DEA0
XL80S 80G 7200RPM
WD800BB-00DKA0
XL80 120G 7200RPM
1200BB-00DWA0
C2 40G 5400 RPM, ATA-100
ST340015A
U9 80G 5400 RPM, ATA-100
ST380012A
Alpine 80G 7200RPM, ATA-100
ST380011A
Alpine 120G 7200RPM, ATA-100
ST3120022A
Appendix B
Components
Hitachi
Specifications
Model Description
40G 7200RPM, ATA-100
Vancover III HDS722540VLAT20
80G 7200RPM, ATA-100
Vancover III HDS722580VLAT20
80G 7200RPM
120G 7200RPM, ATA-100
Vancover III HDS722580VLAT20
120G 7200RPM
52X
F564E
52X/24X/52X
LTR-52246S
CD-ROM
BTC
CD-RW
Liteon
DVD
Liteon
16X/40X
XJ-HD166S
Pioneer
16X/40X
DVD-121RD
16X/40X
DVD-121CHF
16X/40X
GDR-8162B
48X Combo
GCC-4480B
NEC
4X DVD DUAL
ND-1300A
Pioneer
4X DVD DUAL
DVR-106RD
4X DVD SuperMulti Plus
GSA-4040B
HLDS
Combo
HLDS
DVD Dual
SuperMultiPlus
HLDS
Modem Card
GVC
F-1156I(+)/R12-AAP
F-1156I(+)/R12-USA
F-1156I(+)/R12-Australia
Housing
Foxconn
Microtower/3*3.5"+2*5.25"
TF165
SPS
FSP
FSP200-ATV(A), 230W non-PFC SPS
FSP200-ATV(A)(PF), 230W PFC SPS
FDD
Panasonic
1.44M 3.5”
7-in-1 card reader
ECS
3.5" (black) 7-in-1 card reader
UCR-61
3.5" (black) 7-in-1 card reader
UCR-61, w/1394
Daughter Board
Foxconn
USB/Audio daughter board
Mouse
KYE
PS/2 mouse, 2 button+wheel
PowerScroll PS2
USB optical mouse, 2 button+wheel
PowerScroll USB
USB, 3" *2
Thyme510
Speaker
Neosonica
Monitor
Appendix B
95
Components
Compal
Specifications
Model Description
17" CRT
MONITOR,AC711,TCO99,N.M.,W/
EUROPE POWER CORD
17" CRT
MONITOR,AC711,TCO99,N.M.,W/UK
POWER CORD
17" CRT
MONITOR,AC711,TCO99,N.M.,W/O
POWER CORD
17" CRT
MONITOR,AC711,TCO99,N.M.,W/US
POWER CORD(STK)
17" CRT MONITOR,AC711,MPRII,N.M.,W/
US POWER CORD(AAC)
17" CRT MONITOR,AC711,MPRII,N.M.,W/
O POWER CORD
17" CRT MONITOR,AC711,MPRII,E.M.,W/
O POWER CORD
17" CRT MONITOR,AC711,MPRII,S.M.,W/
O POWER CORD
17" CRT MONITOR,AC711,MPRII,S.M.W/
AUSTRALIA POWER CORD
17" CRT MONITOR,AC711,MPRII,N.M.,W/
EUROPE POWER CORD
17" CRT MONITOR,AC711,MPRII,N.M.,W/
US POWER CORD(STK)
17" CRT MONITOR,AC711,MPRII,E.M.,W/
O POWER CORD(AAC)
17" CRT MONITOR,AC711,MPRII,N.M.,W/
CHINA POWER CORD
96
Appendix B
Components
Compal
Specifications
Model Description
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/EUROPE POWER
CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/UK POWER CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/O POWER CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/AUSTRALIA
POWER CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/SWISS POWER
CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/CHINA POWER
CORD
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/US POWER
CORD(AAC)
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/US POWER
CORD(STK)
15" LCD MONITOR,AL511(002),W/O
SPEAKER,TCO99,W/US POWER
CORD(STK)
Jean
15" LCD MONITOR,AL513,W/O
SPEAKER,TCO99,W/US POWER
CORD(STK)
15' LCD MONITOR,AL512,W/
SPEAKER,TCO99,W/US POWER
CORD(STK)
Liteon
17" CRT,86K,AC707,MPRII,N.M.,W/US
POWER CORD(STK)
17" LCD MONITOR, AL702,W/ SPEAKER,
TCO99, W/US POWER CORE (STK)
15' LCD MONITOR,AL512,W/
SPEAKER,TCO99,W/US POWER
CORD(STK)
Liteon
17" CRT,86K,AC707,MPRII,N.M.,W/US
POWER CORD(STK)
17" LCD MONITOR, AL702,W/ SPEAKER,
TCO99, W/US POWER CORE (STK)
Appendix B
97
98
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides for all models
T
User's manuals
T
Training materials
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveler's Warranty (ITW)
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
99
100
Appendix C
Download PDF

advertising