Operator’s Manual Precedent™ Rear Remote Control Panel

Operator’s Manual Precedent™ Rear Remote Control Panel
Operator’s Manual
Ingersoll Rand’s Climate Solutions sector delivers energy-efficient HVACR solutions for
customers globally. Its world class brands include Thermo King, the leader in transport
temperature control and Trane, a provider of energy efficient heating, ventilating and
air conditioning systems, building and contracting services, parts support and advanced
controls for commercial buildings and homes.
Precedent™ Rear
Remote Control Panel
(Place this document with unit Operator’s Manual)
TK 56211-2-OP (Rev. 0, 09/15)
©2015 Ingersoll-Rand Company
Printed in U.S.A.
Operator’s Manual
Ingersoll Rand’s Climate Solutions sector delivers energy-efficient HVACR solutions for
customers globally. Its world class brands include Thermo King, the leader in transport
temperature control and Trane, a provider of energy efficient heating, ventilating and
air conditioning systems, building and contracting services, parts support and advanced
controls for commercial buildings and homes.
©2015 Ingersoll-Rand Company
Printed in U.S.A.
Precedent™ Rear
Remote Control Panel
(Place this document with unit Operator’s Manual)
TK 56211-2-OP (Rev. 0, 09/15)
Precedent™
Rear Remote Control Panel
(Place this document with unit Operator’s Manual)
TK 56211-2-OP (Rev. 0, 09/15)
Copyright© 2015 Thermo King Corp., Minneapolis, MN, USA
Printed in USA
Table of Contents
Rear Remote Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rear Remote Control Panel Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rear Remote Control Action Set to Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rear Remote Control Action Set to STAND BY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Reading a Typical Remote Standard Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Remote Control Panel Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Turning the Unit ON or OFF (Configured for STAND BY Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Turning the Unit On and Off (Configured for RUN Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Changing the Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Selecting Cycle-Sentry or Continuous Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Displaying the Discharge Air Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Viewing and Clearing Alarm Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Starting a Manual Defrost Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Sending a Start of Trip Marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Running a Pretrip Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2
Rear Remote Control Panel
The optional Rear Remote Control Panel is connected to the
control system and is used to operate the unit from a remote
location, typically at the rear of the trailer. In the illustration
below all display segments are turned on.
Rear Remote Control Panel
Functionality
The Rear Remote Control Panel functions that are available to
the user are determined by the setting of the Rear Remote
Control Action features in the Guarded Access / Unit
Configuration Menu. The Rear Remote Control Action can be
set to either RUN or STAND BY.
When the unit is turned on at the Rear Remote Control Panel
either the Standard Display or [STAnd by] will appear on the
display.
Figure 1: Rear Remote Control Panel
Rear Remote Control Action Set to
Run
If the Rear Remote Control Action is set to RUN the Standard
Display will be present on the Rear Remote Control Panel and
the unit will start and run when the Rear Remote Control Panel
ON Key is pressed. Pressing the Rear Remote Control Panel
OFF Key will turn the unit off.
3
Rear Remote Control Panel
If the control system is powered up from the Rear Remote
Control Panel the Standard Display will appear in both the
Rear Remote Control Panel display and the unit Control Panel
display. When set to RUN the Rear Remote Control Panel
allows the following:
•
Turn the unit on and off
•
Unit will start and run
•
Change the Setpoint
•
Select Cycle-Sentry or Continuous Mode
•
Display discharge air temperature
•
Display and clear alarm codes
•
Initiate a manual defrost cycle
•
Send a Start of Trip marker to the ServiceWatch and
CargoWatch Data Loggers
•
Initiate a Pretrip Test
4
Rear Remote Control Action Set to
STAND BY
If the Rear Remote Control Action is set to STAND BY,
pressing the Rear Remote Control Panel ON Key will power
up the control system, but the unit will not start and run.
Pressing the Rear Remote Control Panel OFF Key will turn the
unit off. The Control Panel on the unit must be used to start and
stop unit operation.
In addition to turning the unit on and off, when set to STAND
BY the Rear Remote Control Panel allows the following:
•
Turn the unit on and off
•
Unit will not start and run
•
Change the Setpoint
•
Select Cycle Sentry or Continuous Mode (unless
prevented by OptiSet Plus)
•
Display discharge air temperature
•
Display and clear alarm codes
•
Send a Start of Trip marker to the ServiceWatch and
CargoWatch Data Loggers
Rear Remote Control Panel
When in STAND BY, the unit will not start and run and a
defrost cycle or Pretrip Test cannot be started.
If the control system is powered up from the remote control
panel a stand by message will appear in both the remote control
panel display and the unit Control Panel display as shown in
Figure 2 and Figure 3.
When the StAnd bY display is shown, press the Select Key to
show the Remote Standard Display. When the remote standard
Display is shown, the setpoint and operating mode can be
changed, the discharge air temperature can be displayed and
alarms can be viewed and cleared. In addition, a Start of Trip
can be sent to the data loggers.
After the last key is pressed, the display will return to the
StAnd bY display shown in Figure 4 in about 10 seconds.
Figure 2: Rear Remote Control Panel Display
Figure 4: Press Select Key
Figure 3: Unit Control Panel Display
5
Rear Remote Control Panel
Keypad
The nine touch sensitive keys are used to turn the unit on and
off. They also allow the setpoint to be changed, Cycle Sentry
or Continuous Mode to be selected, Alarm Codes and other
operating data to be displayed and Pretrip Tests and Defrost
Cycles to be performed. A Start of Trip marker can also be sent
to the data loggers.
Figure 5: Rear Remote Control Panel
ON Key
Turns the unit on as determined
by the setting of Rear Remote
Control Action.
OFF Key
Turns the unit off.
Up Arrow
Key
Increases setpoint or changes
other setting.
Down
Arrow Key
Decreases setpoint or changes
other setting.
Select Key
Allows Cycle-Sentry to be turned
on and off, displays the discharge
air temperature and alarms.
Enter Key
Executes a prompt or loads a
new setpoint or other setting.
Pretrip Key Initiates a Pretrip Test.
6
Rear Remote Control Panel
TK Logo
Key
Sends a Start of Trip marker to
the data logger.
Initiates a defrost cycle if
Defrost Key
conditions allow.
Display
The display normally shows the Standard Display of return air
temperature and setpoint. The icons on either side of the
display indicate operating modes and alarms. The display
shown here has all possible segments lighted. The display
icons are defined below.
Cool Icon
This icon appears when the unit is
cooling.
Heat Icon
This icon appears when the unit is
heating.
Modulation
Icon
This icon appears when the unit is
in modulation.
Defrost Icon
This icon appears when the unit is
defrosting.
Cycle-Sentry This icon appears when the unit is
Icon
operating in Cycle-Sentry mode.
Alarm Icon
This icon appears when an alarm
condition has been detected.
This icon appears when the unit is
Electric
operating in the optional electric
Standby Icon
standby mode.
Figure 6: Rear Remote Control Panel
Setpoint
Icon
This icon appears when the
setpoint is being shown in the
display.
Not Used
This icon appears during a remote
control panel test but is not
currently used.
7
Rear Remote Control Panel
Reading a Typical Remote
Standard Display
The Remote Standard Display shows the temperature and
setpoint. The icons at the sides of the display indicate operating
conditions.
Remote Control Panel Lockout
The remote control panel may be locked out during some
control system functions such as Service Test Mode, Interface
Board Test Mode and while setting programmable features. If
this is the case the display shown in Figure 8 will appear. The
display will return to the Remote Standard Display when
allowed by the control system.
Figure 7: Remote Standard Display
The Remote Standard Display in Figure 7 shows the following
information:
• The temperature (typically return air temperature) is
35.8°F.
• The setpoint is 35°F.
• The unit is cooling as shown by the icon at the upper left
side of the display.
• The unit is operating in Cycle Sentry mode as shown by
the icon at the upper right side of the display.
8
Figure 8: Remote Lock Out Display
Rear Remote Control Panel
Turning the Unit ON or OFF
(Configured for STAND BY
Operation)
The control system is turned on by pressing the ON Key and
off by pressing the OFF Key. When the On Key is pressed the
remote display briefly shows all segments and then StAnd by
as shown in Figure 9. A stand by message will also appear on
the unit Control Panel display. The setpoint can be changed but
the unit will not start and run. Only the Select Key, Enter Key
and Up and Down Arrow Keys are functional. The unit can be
started and run by pressing the unit Control Panel ON Key.
Turning the Unit On and Off
(Configured for RUN Operation)
The unit is turned on by pressing the ON key and off by
pressing the OFF key. When the ON key is pressed the remote
display briefly shows all segments and then COn FIg as the
control system initializes. Then the Remote Standard Display
will appear as shown in Figure 10. The unit will start and run if
necessary.
IMPORTANT: To change the setpoint, press the Select Key to
show the Remote Standard Display. The setpoint can now be
changed as shown on page 10.
Figure 10: Standard Display
Figure 9: Stand By Display
9
Rear Remote Control Panel
Changing the Setpoint
The setpoint can be changed when the Remote Standard
Display is shown.
1.
When the Remote Standard Display is shown, press the
Up or Down Arrow Keys to select the desired setpoint
(Figure 11).
Figure 11: Press Up or Down Arrow Keys
2.
10
When the desired setpoint is shown on the display,
immediately press the Enter Key to load the new setpoint.
The display will briefly show [Lod] and then the new
setpoint will reappear in the display.
IMPORTANT: The Enter key (Figure 12) must be pressed or
the setpoint will not be changed. The display will return to the
Standard Display and the setpoint will return to the old
setpoint in about 10 seconds if the Enter Key is not pressed.
Alarm Code 127 Setpoint Not Entered is set, to indicate that
the setpoint change was started but not completed.
Figure 12: Press Enter Key
IMPORTANT: Confirm that the correct setpoint is set.
Rear Remote Control Panel
Selecting Cycle-Sentry or
Continuous Mode
Cycle Sentry or Continuous Mode operation can be changed
using the Select Key.
1.
When the Remote Standard Display is shown, press the
Select key once to display the Cycle Sentry prompt.
Figure 14: Press Up or Down Arrow Keys
3.
When the desired selection is shown, press the Enter Key
(Figure 15) to load the setting. The display will briefly
show [Lod] and then the new selection will briefly appear
in the display.
Figure 13: Press Select Key
2.
Use the Up and Down Arrow Keys to chose either YES or
nO. Yes = Cycle Sentry Mode. nO = Continuous Mode.
Figure 15: Press Enter Key
4.
The display will then return to the Remote Standard
Display.
11
Rear Remote Control Panel
Displaying the Discharge Air
Temperature
Viewing and Clearing Alarm
Codes
The discharge air temperature can be shown using the Select
Key.
Alarm Codes can be displayed and cleared using the Select
Key.
1.
1.
When the Remote Standard Display is shown, press the
Select Key twice. The discharge air temperature will be
shown in the display for about 10 seconds.
When the Remote Standard Display is shown, press the
Select Key three times. Any alarm codes present will be
shown in the display, with the most recent alarm code
shown first. If no alarm codes are present the display will
show [00].
Figure 16: Press Select Key Twice
2.
The display will then return to the Remote Standard
Display.
Figure 17: Press Select Key Three Times
2.
12
To clear a displayed alarm code, press the Enter Key. The
display will briefly show CLEAr ALm.
Rear Remote Control Panel
Starting a Manual Defrost Cycle
If conditions allow, a manual defrost cycle can be initiated
using the Defrost Key.
1.
Press the Defrost Key. The defrost prompt [EnTEr dEF]
will appear in the display.
Figure 18: Press Enter Key
3.
If any additional alarms are present, the next alarm will be
shown. If no other alarms are present the display will
briefly show [00].
Figure 20: Press Defrost Key
2.
Figure 19: No Alarms Display
4.
When the defrost prompt is shown, press the Enter Key to
start a manual defrost. The display will briefly show
LOAd dEF and then a defrost cycle will begin if
conditions allow.
The display will then return to the Remote Standard
Display.
13
Rear Remote Control Panel
Sending a Start of Trip Marker
A Start of Trip marker can be sent to the data loggers using the
TK Logo Key.
1.
Press the TK Logo Key. The Start of Trip [EnTEr SOt]
prompt will appear in the display.
Figure 21: Press Enter Key
3.
The display will return to the Remote Standard Display.
The Defrost Icon will be shown in the display.
Figure 23: Press TK Logo Key
Figure 22: Defrost Icon Displayed
4.
14
The defrost cycle will terminate automatically.
Rear Remote Control Panel
2.
When the Start of Trip prompt is shown, press the Enter
Key to send a Start of Trip marker to the CargoWatch and
ServiceWatch data loggers. The display will briefly show
LOAd SOt.
1.
Clear any alarm codes as shown previously.
2.
Press the Pretrip Key. The Pretrip [EntEr PrE] prompt will
appear in the display.
Figure 25: Press Pretrip Key
Figure 24: Press Enter Key
3.
The display will then return to the Remote Standard
Display.
Running a Pretrip Test
3.
When the Pretrip prompt is shown, press the Enter Key to
start a Pretrip Test. The display will briefly show LOAd
PrE. If the unit is not running a Full Pretrip Test will be
performed. If the unit is running a Running Pretrip Test
will be performed.
A Pretrip Test can be started using the Pretrip Key as long as
the unit is not in STAND BY. If the unit is not running when
the Pretrip Test is started a Full Pretrip Test will be performed.
If the unit is running when the Pretrip Test is started a Running
Pretrip Test will be performed.
15
Rear Remote Control Panel
5.
When the Pretrip Test is complete the display will show
PASS, CHEC or FAIL. Pressing the Select Key will return
to the Remote Standard Display.
Figure 26: Press Enter Key
4.
When the Pretrip Test is running the display will show PrE
trP. The Control Panel will show the Pretrip Test progress.
Figure 27: Pretrip Display
16
Figure 28: Pass Pretrip Display
Operator’s Manual
Ingersoll Rand’s Climate Solutions sector delivers energy-efficient HVACR solutions for
customers globally. Its world class brands include Thermo King, the leader in transport
temperature control and Trane, a provider of energy efficient heating, ventilating and
air conditioning systems, building and contracting services, parts support and advanced
controls for commercial buildings and homes.
Precedent™ Rear
Remote Control Panel
(Place this document with unit Operator’s Manual)
TK 56211-2-OP (Rev. 0, 09/15)
©2015 Ingersoll-Rand Company
Printed in U.S.A.
Operator’s Manual
Ingersoll Rand’s Climate Solutions sector delivers energy-efficient HVACR solutions for
customers globally. Its world class brands include Thermo King, the leader in transport
temperature control and Trane, a provider of energy efficient heating, ventilating and
air conditioning systems, building and contracting services, parts support and advanced
controls for commercial buildings and homes.
©2015 Ingersoll-Rand Company
Printed in U.S.A.
Precedent™ Rear
Remote Control Panel
(Place this document with unit Operator’s Manual)
TK 56211-2-OP (Rev. 0, 09/15)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement