09n8216
IBM® Netfinity® 7600
IBM
Installation Guide
SC09-N821-60
NOTE
Before using this information and the product it supports, be sure to read the general information in
“Appendix A. Product warranties and notices,” on page 31.
First Edition (March 2000)
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION, 2000. All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or disclosure is subject
to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Appendix A. Product warranties and
notices . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 1.Introduction . . . . . . . . . . . . . . . . 1
Warranty Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
IBM Statement of Limited Warranty for United States,
Puerto Rico, and Canada (Part 1 - General Terms) . 31
IBM Statement of Warranty Worldwide except
Canada, Puerto Rico, Turkey, United States (Part 1 –
General Terms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Part 2 - Worldwide Country-Unique Terms . . . . . . . 36
Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Edition Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Year 2000 readiness and instructions. . . . . . . . . . . . . 41
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Electronic emission notices . . . . . . . . . . . . . . . . . . . . . . . 42
Federal Communications Commission (FCC)
Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Industry Canada Class A emission compliance
statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Australia and New Zealand Class A statement. . . . 43
United Kingdom telecommunications safety
requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
European community directive conformance
statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Taiwan electrical emission statement . . . . . . . . . . . . 44
Japanese Voluntary Control Council for Interference
(VCCI) statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications and features . . . . . . . . . . . . . . . . . . . . . . . . 2
Notices used in this book . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Major components of the Netfinity 7600 server . . . . . . . 4
Chapter 2.Installing options . . . . . . . . . . . 7
Working inside a server with power on. . . . . . . . . . . . . . 7
Installing adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing memory options. . . . . . . . . . . . . . . . . . . . . . . . 10
Installing a drive in a hot-swap bay . . . . . . . . . . . . . . . . 12
Installing a microprocessor . . . . . . . . . . . . . . . . . . . . . . . 13
Installing a hot-swap power supply. . . . . . . . . . . . . . . . 14
Cabling the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chapter 3.Starting the server . . . . . . . . . . 17
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Information LED panel. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 4.Configuring your server . . . . . 21
Using the ServerGuide CDs. . . . . . . . . . . . . . . . . . . . . . . 21
After installing the NOS . . . . . . . . . . . . . . . . . . . . . . . 22
Netfinity systems management solutions . . . . . . . . . . . 22
Chapter 5.Solving problems . . . . . . . . . . . 23
POST beep code descriptions . . . . . . . . . . . . . . . . . . . . .
POST error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ServerGuide startup problems . . . . . . . . . . . . . . . . . . . .
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
24
26
27
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
IBM® Netfinity® 7600 Installation Guide
Safety
Before installing this product, read the Safety Information book.
Antes de instalar este produto, leia o Manual de Informações sobre Segurança.
Před instalací tohoto produktu si přečtěte příručku bezpečnostních instrukcí.
Læs hæftet med sikkerhedsforskrifter, før du installerer dette produkt.
Lue Safety Information -kirjanen, ennen kuin asennat tämän tuotteen.
Avant de procéder à l'installation de ce produit, lisez le manuel Safety Information.
Vor Beginn der Installation die Broschüre mit Sicherheitshinweisen lesen.
Przed zainstalowaniem tego produktu należy przeczytać broszurę Informacje Dotyczące
Bezpieczeństwa.
Prima di installare questo prodotto, leggere l'opuscolo contenente le informazioni
sulla sicurezza.
© Copyright IBM Corp. 2000
v
Lees voordat u dit product installeert eerst het boekje met veiligheidsvoorschriften.
Les heftet om sikkerhetsinformasjon (Safety Information) før du installerer dette
produktet.
Antes de instalar este produto, leia o folheto Informações sobre Segurança.
Перед установкой продукта прочтите брошюру по технике безопасности
(Safety Information).
Pred inštaláciou tohto produktu si pre ítajte Informa nú brožúrku o bezpe nosti.
Preden namestite ta izdelek, preberite knjižico Varnostne informacije.
Antes de instalar este producto, lea la Información de Seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Installálás el tt olvassa el a Biztonsági el írások kézikönyvét !
vi
IBM® Netfinity® 7600 Installation Guide
Statement 1
Danger
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
•
Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
•
Connect all power cords to a properly wired and grounded electrical outlet.
•
Connect to properly wired outlets any equipment that will be attached to
this product.
•
When possible, use one hand only to connect or disconnect signal cables.
•
Never turn on any equipment when there is evidence of fire, water, or
structural damage.
•
Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless instructed
otherwise in the installation and configuration procedures.
•
Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To connect:
To disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from
outlet.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
3. Remove signal cables from
connectors.
4. Remove all cables from devices.
vii
Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode
if not properly used, handled, or disposed of.
Do not:
•
Throw or immerse into water.
•
Heat to more than 100 C (212 F)
•
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
•
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Danger
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note
the following. Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the beam.
viii
IBM® Netfinity® 7600 Installation Guide
Statement 4
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
ix
Statement 5
CAUTION:
The power control button on the device and the power supply do not turn off
the electrical current supplied to the device. The device also might have more
than one power cord. To remove all electrical current from the device, ensure
that all power cords are disconnected from the power source.
1
2
3
x
IBM® Netfinity® 7600 Installation Guide
Chapter 1. Introduction
Thank you for purchasing an IBM® Netfinity® 7600 server. This Installation Guide
provides the information needed to:
•
Set up and cable your server
•
Start and configure your server
•
Install your network operating system (NOS)
Packaged with this Installation Guide are software CDs that help you configure
hardware, install device drivers, and install the network operating system (NOS).
Also included is an IBM Netfinity Documentation CD that provides detailed
information about this server.
Your server comes with a three-year limited warranty and 90-Day IBM Start Up
Support. If you have access to the World Wide Web, you can obtain up-to-date
information about your server model and other IBM server products at the following
World Wide Web address:
http://www.ibm.com/pc/us/netfinity/
Refer to the Rack Installation Instructions for complete details on rack installation and
removal instructions.
Record your product information in this table.
© Copyright IBM Corp. 2000
Product name
_________________________________________
Machine type
_________________________________________
Model number
_________________________________________
Serial number
_________________________________________
1
Specifications and features
The following table provides a summary of the features and specifications for your
Netfinity 7600 server.
Environment:
Microprocessor:
Size
•
Intel® Pentium®III Xeon™
•
Height: 356 mm (14 in.) (8U)
•
32 KB of level-1 cache
•
Depth: 650 mm (25.6 in.)
•
1 MB of level-2 cache (min)
•
Width: 440 mm (17.3 in.)
•
Expandable to four
microprocessors
•
Weight: 34.4 kg (76 lb.) to 61
kg (134 lb.) depending upon
configuration
•
— Server on: 10° to 35° C
(50° to 95° F). Altitude: 0
to 914 m (3000 ft.)
— Server on: 10° to 32° C
(50° to 89.6° F). Altitude:
914 m (3000 ft.) to 2133
m (7000 ft.)
Memory:
•
Maximum: 16 GB
Integrated functions:
•
Type: ECC, SDRAM,
Registered DIMMs
•
Netfinity Advanced System
Management processor
•
Slots: 4-way interleaved, 16
slots
•
IBM ServeRAID controller
(three channels)
•
Dual channel Ultra2 (LVD)
SCSI controller, one
external port, one internal
port
Drives standard:
•
Diskette: 1.44 MB
•
CD-ROM: 40X IDE
•
•
Humidity:
— Server on: 8% to 80%
— Server off: 8% to 80%
Heat output:
One 10BASE-T/100BASETX AMD Ethernet controller
Hot-swap: 10 slim-high or 7
half high
•
Two serial ports
•
One parallel port
Non-hot-swap: Two 5.25inch
•
Two universal serial bus
ports
•
Minimum configuration:
1023.9 BTU
•
Keyboard port
•
•
Mouse port
Maximum configuration:
2764.6 BTU
•
Video port
PCI expansion slots:
•
Four 33 MHz 64-bit
•
Two 66 MHz 64-bit
Hot-swap power supplies:
Acoustical noise emissions:
•
Sound power, idling: 6.3 bel
maximum
•
Sound power, operating: 6.3
bel maximum
•
Sound pressure, operating:
48 dBa maximum
250 Watt (115-230 V ac)
•
Minimum: Three
•
Maximum: Four
Redundant cooling:
•
— Server off: 10° to 43° C
(50° to 110° F).
Maximum altitude: 2133
m (7000 ft.)
•
Expansion bays:
•
Air temperature:
Four hot-swap fan
assemblies
Video:
Approximate heat output in
British Thermal Units (BTU) per
hour
Electrical input:
•
Sine-wave input (50-60 Hz)
required
•
Input voltage low range:
— Minimum: 90 V ac
— Maximum: 137 V ac
•
Input voltage high range:
— Minimum: 180 V ac
— Maximum: 265 V ac
•
Input kilovolt-amperes
(kVA) approximately:
•
S3 video controller
— Minimum: 0.08 kVA
•
Compatible with SVGA and
VGA
— Maximum: 0.52 kVA
•
4 MB video memory
Table 1. Features and specifications
2
IBM® Netfinity® 7600 Installation Guide
Notices used in this book
This information product contains notices that relate to a specific topic. The Caution
and Danger notices also appear in the multilingual safety booklet that came with your
Netfinity product. Each notice is numbered for easy reference to the corresponding
notices in the safety booklet.
The notice definitions are as follows:
•
Notes: These notices provide important tips, guidance, or advice.
•
Attention: These notices indicate possible damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in
which damage could occur.
•
Caution: These notices indicate situations that can be potentially hazardous to
you. A caution notice is placed just before descriptions of potentially hazardous
procedure steps or situations.
•
Danger: These notices indicate situations that can be potentially lethal or
extremely hazardous to you. A danger notice is placed just before descriptions of
potentially lethal or extremely hazardous procedure steps or situations.
Chapter 1. Introduction
3
Major components of the Netfinity 7600 server
The orange color on components and labels in your server identifies hot-swap or hotplug components. This means that you can install or remove the components while
the system is running, provided that your system is configured to support this
function. For complete information about installing or removing a hot-swap or hotplug component, see the information provided in the procedures in this document.
The blue color on components and labels indicates touch points where a component
can be gripped, a latch moved, and so on.
Hot-swap
drive
4
Removable-media
drive
IBM® Netfinity® 7600 Installation Guide
Filler Panel
Fan assembly
Power supply
Terminator card
Memory
module
Memory board
Shuttle
Microprocessor
I/O board
Chapter 1. Introduction
5
6
IBM® Netfinity® 7600 Installation Guide
Chapter 2. Installing options
This chapter provides the basic information needed to install hardware options in
your server. This section is for all users, but is written with the experienced user in
mind. If you need more detailed installation information, see the User’s Reference on
the IBM Netfinity Documentation CD.
Working inside a server with power on
Your server supports hot plug, hot add, and hot swap devices and is designed to
operate safely while turned on with the cover removed. Follow these guidelines when
you work inside a server that is turned on:
•
Avoid loose-fitting clothing on your forearms. Button long-sleeved shirts before
working inside the server; do not wear cufflinks while you are working inside
the server.
•
Do not allow your necktie or scarf to hang inside the server.
•
Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist
watches.
•
Remove items from your shirt pocket (such as pens or pencils) that could fall
into the server as you lean over it.
•
Take care to avoid dropping any metallic objects, such as paper clips, hair pins,
or screws, into the server.
Installing adapters
This section describes how to install hot-plug PCI adapters. Before you continue with
the adapter-installation procedure, review the following:
•
Slots 1 and 2 support 3.3 V and universal non-hot-plug PCI adapters only.
•
Slots 3–6 support 5.0V and universal PCI adapters.
Note:
Universal PCI adapters support both 3.3V and 5.0V operation.
•
The system scans PCI slots 1 through 6 to assign system resources; then, the
system starts (boots) the PCI devices in the following order: processor and I/O
board devices, slots 1 and 2, and then slots 3 through 6.
•
You can install hot-plug PCI adapters in PCI slots 3-6. You can also install nonhot-plug PCI adapters in these slots.
© Copyright IBM Corp. 2000
7
The illustrations in this document might differ slightly from your hardware.
Non-hot-plug PCI slots
1-2 (on PCI bus A)
External Attention LEDs for
hot-plug slots
Internal Attention LEDs for
hot-plug slots
Power LEDs
for hot-plug slots
8
IBM® Netfinity® 7600 Installation Guide
Hot-plug PCI slots
3-6 (on PCI bus B)
The following illustration shows the installation of a hot-plug adapter.
Adapter
retention latch
Adapter retention latch
Adapter
Tab
Attention: When you handle Electrostatic Discharge-Sensitive devices (ESD), take
precautions to avoid damage from static electricity. For details on handling these
devices, refer to the following Web site and use a search term of ESD:
http://www.ibm.com/
To install an adapter.
1. Review the information in “Safety” on page v.
2. If you are installing a non-hot-plug adapter, turn off the server and disconnect all
cables.
3. Remove the top cover.
4. Select a slot, open the tab and the expansion-slot cover, and remove the
expansion-slot cover.
5. Install the adapter in the slot; then, close the tab and adapter retention latch.
6. Install the top cover.
7. If you installed a non-hot-plug adapter, connect all cables and power cords.
Chapter 2. Installing options
9
Installing memory options
Before you install memory, review the following:
•
All the DIMMs installed in each set must be the same size and speed, but all the
sets do not have to contain DIMMs of the same size and speed.
•
The memory board contains 16 DIMM connectors and supports 4-way memory
interleaving.
•
Install only 3.3 V, 168-pin, 8-byte, registered DIMMs. Only 100 MHz, 72-bit,
registered, synchronous, error correcting code (ECC), SDRAM configuration
DIMM memory is supported for the 128 MB, 256 MB, 512 MB and 1 GB DIMMs.
•
If you install 4 GB of memory, some of the memory is reserved for system
resources. The amount reserved for system resources depends on the
configuration of the server.
•
If you install 16 GB of memory, the Configuration/Setup Utility will display the
memory that is usable by the network operating system. This amount of
memory might differ from the amount of memory you have installed.
•
Installing or removing DIMMs changes the configuration information in the
server. Therefore, after installing or removing a DIMM, you must save the new
configuration information using the Configuration/Setup Utility program. See
the User’s Reference on the IBM Netfinity Publication CD for more information.
•
Install the DIMMs as shown in Table 2.
Set of 4 DIMMs
First set (shipped as standard)
J1, J5, J9, J13
2nd set
J2, J6, J10, J14
3rd set
J3,J 7,J 11,J 15
4th set
J4, J8, J12, J16
Table 2. DIMM installation order
10
install DIMMs in these connectors:
IBM® Netfinity® 7600 Installation Guide
The illustrations in this document might differ slightly from your hardware.
Pop rivets
Processor housing
cover
DIMM
Memory board
Attention: When you handle Electrostatic Discharge-Sensitive devices (ESD), take
precautions to avoid damage from static electricity. For details on handling these
devices, refer to the following Web site and use a search term of ESD:
http://www.ibm.com/
To install a memory module:
1. Review the information in “Safety” on page v.
2. Turn off the server and remove the power cords.
3. Remove the top cover.
4. Remove the processor housing cover and remove the memory board assembly
from the server.
5. Select the connectors in which to install the DIMMs.
6. Install the DIMMs in the connectors.
7. Replace the memory board assembly in the server and replace the processor
housing cover.
8. Install the top cover.
9. Connect all cables and power cords.
Chapter 2. Installing options
11
Installing a drive in a hot-swap bay
Your server supports ten 1-inch (26 mm) slim-high or seven 1.6-inch (42 mm) halfhigh, 3.5-inch hot-swap hard disk drives in the hot-swap bays.
Note:
See the User’s Reference on the IBM Netfinity Documentation CD for
information on installing devices in the non-hot-swap bays.
The illustrations in this document might differ slightly from your hardware.
Slim filler
Filler panel
Drive tray handle
(in open position)
Attention: When you handle Electrostatic Discharge-Sensitive devices (ESD), take
precautions to avoid damage from static electricity. For details on handling these
devices, refer to the following Web site and use a search term of ESD:
http://www.ibm.com/
To install a drive in a hot-swap bay:
1. Review the information in “Safety” on page v.
2. Remove the filler panel.
3. Place the drive handle in the open position and slide the drive into the bay.
4. Close the drive handle.
5. If there is a gap above or below the drive, remove the slim filler from the filler
panel and install it above or below the drive.
12
IBM® Netfinity® 7600 Installation Guide
Installing a microprocessor
Your server comes with one microprocessor installed in connector J2. This is the
startup (boot) microprocessor. A microprocessor installed in connector J3 is
microprocessor 2; a microprocessor installed in connector J4 is microprocessor 3; a
microprocessor installed in connector J5 is processor 4. If more than one
microprocessor is installed, the highest numbered microprocessor is the one the server
will start from. The lower numbered microprocessors are used as application
microprocessors.
The illustrations in this document might differ slightly from your hardware.
Pop rivets
Processor housing
cover
VRM
Terminator card
Attention: When you handle Electrostatic Discharge-Sensitive devices (ESD), take
precautions to avoid damage from static electricity. For details on handling these
devices, refer to the following Web site and use a search term of ESD:
http://www.ibm.com/
To install an additional microprocessor kit:
1. Review the information in “Safety” on page v.
2. Turn off the server and remove the power cords.
3. Remove the top cover.
4. Remove the processor housing cover.
5. Remove the terminator card from the connector.
6. Install the microprocessor.
Note:
Each microprocessor connector must contain either a terminator card or a
microprocessor.
7. Install the voltage regulator module (VRM).
8. Install the processor housing cover.
9. Install the top cover.
10. Cable the server and connect all power cords.
Chapter 2. Installing options
13
Installing a hot-swap power supply
If you install or remove a power supply, observe the following precautions:
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any component
that has this label attached. There are no serviceable parts inside these
components. If you suspect a problem with one of these parts, contact a service
technician.
14
IBM® Netfinity® 7600 Installation Guide
The illustrations in this document might differ slightly from your hardware.
Attention: When you handle Electrostatic Discharge-Sensitive devices (ESD), take
precautions to avoid damage from static electricity. For details on handling these
devices, refer to the following Web site and use a search term of ESD:
http://www.ibm.com/
Handle
Filler panel
DC power light
AC power light
To install an additional power supply:
1. Review the information in “Safety” on page v.
2. Remove the filler panel.
3. Place the handle on the power supply in the open position.
4. Slide the power supply into the chassis and press the handle to the closed
position.
5. Plug the power cord into the power supply; then, into a properly grounded
electrical outlet.
6. Verify that the DC Power light and the AC Power light on the power supply are
lit, indicating that the power supply is operating properly.
Statement 6
CAUTION:
If you install a strain-relief bracket option over the end of the power cord that is
connected to the device, you must connect the other end of the power cord to an
easily accessible power source
Chapter 2. Installing options
15
Cabling the server
Refer to the following illustration for the location of the input and output connectors
on your server.
The illustrations in this document might differ slightly from your hardware.
Parallel
Serial A
System management
Ethernet
Serial B
ASM Interconnect
port A
USB1
USB2
ASM Interconnect
port B
Video
Ultra2 SCSI
Keyboard
Mouse
Refer to the following illustration for an example of proper cable routing.
16
IBM® Netfinity® 7600 Installation Guide
Chapter 3. Starting the server
Use the following procedure to start your server.
1. Turn on all external devices, such as the monitor.
Note:
After you plug the power cord into an outlet, wait 20 seconds before
pressing the power control button. During this time, the power control
button will not respond because the system management microprocessor
is being initialized.
2. Press the power control button on the front of the server. The power-on light
comes on and the power-on self-test (POST) begins.
Controls and indicators
The following illustration shows the controls and indicators on the server.
Information LED panel
Power-control button
Reset button
Diskette drive in-use light
Diskette-eject button
CD-ROM drive in-use light
CD-ROM eject/load button
Hard-disk
activity light
Hard-disk
status light
Hard-disk drive status light: Each of the hot-swap drives has a status light.
When this amber light is on continuously, the drive has failed. When the light
flashes slowly (one flash per second), the drive is being rebuilt. When the light
flashes rapidly (three flashes per second), the controller is identifying the drive.
Hard-disk activity light: Each of the hot-swap drives has a hard-disk activity
light. When this green light is flashing, the drive is being accessed.
CD-ROM eject/load button: Press this button to eject or retract the CD-ROM
tray.
CD-ROM drive in-use light: When this light is on, the CD-ROM drive is being
accessed.
Diskette-eject button: Press this button to eject a diskette from the drive.
Diskette drive in-use light: When this light is on, the diskette drive is being
accessed.
© Copyright IBM Corp. 2000
17
Reset button: Press this button to reset the server and run the power-on self-test
(POST).
Power control button: Press this button to manually turn on or off the server.
You can start the server in several ways:
— You can turn on the server by pressing the Power Control button on the
front of the server.
Note:
After you plug the power cords of your server into electrical outlets,
wait 20 seconds before pressing the Power Control button. During
this time the system-management processor is initializing and the
Power Control button does not respond.
— If the server is turned on, a power failure occurs, and unattended-start mode
is enabled in the Configuration/Setup utility program, the server will start
automatically when power is restored.
— If AC power is present, the server is off, and the wake-up feature is enabled
in the Configuration/Setup utility program, the wake-up feature will turn
on the server at the set time.
— If AC power is present, the server is off, and ring-signal detect is enabled in
the Configuration/Setup utility program, you can turn on the server by
telephone input.
— The Netfinity Advanced System Management Processor also can turn on the
server.
You can turn off the server in several ways:
— You can turn off the server by pressing the Power Control button on the
front of the server. Pressing the Power Control button starts an orderly
shutdown of the operating system, if this feature is supported by your
operating system, and places the server in standby mode.
18
IBM® Netfinity® 7600 Installation Guide
Statement 5
CAUTION:
The power control button on the device and the power supply do not turn off
the electrical current supplied to the device. The device also might have more
than one power cord. To remove all electrical current from the device, ensure
that all power cords are disconnected from the power source.
1
2
3
Note:
After turning off the server, wait at least 5 seconds before pressing
the Power Control button to power the server on again.
— You can press and hold the Power Control button for more than 4 seconds to
cause an immediate shutdown of the server and place the server in standby
mode. You can use this feature if the operating system stalls.
— You can disconnect the server power cords from the electrical outlets to shut
off all power to the server.
Note:
Wait about 15 seconds after disconnecting the power cords for your
system to stop running. Watch for the System Power light on the
operator information panel to stop blinking.
Information LED panel: The lights on this panel give status information for
your server. See “Information LED panel”.
Chapter 3. Starting the server
19
Information LED panel
The following illustration shows the status lights on the Information LED panel.
POST-complete
System power
OK
System error
Hard disk drive
activity
1
2
3
4
100 LINK TX
MB OK
RX
Information
Processor
activity
Ethernet speed
Ethernet-link
status
Ethernet
transmit/receive
activity
System power light: When this green light is on, power is present in the server.
When this light flashes, the server is in standby mode (the system power supply
is turned off and ac current is present). When this light is off, the power
subsystem, the ac power, or a light has failed.
Attention: If the system power light is off, it does not mean there is no electrical
current present in the server. The light might be burned out. To remove all
electrical current from the server, you must unplug the server power cords from
the electrical outlets or from the uninterruptible power device.
POST-complete light: This green light is on when the power-on self-test (POST)
completes without any errors.
Hard disk drive activity light: This green light flickers when there is activity on
a hard disk drive.
Processor activity lights: One or more of these green lights are on when there is
microprocessor activity. The number of lights that are on indicates the number of
microprocessors with activity.
Information light: When this amber light is on, the server power supplies are
nonredundant or some other noncritical event has occurred. The event is
recorded in the Event log. See the User’s Reference on the IBM Netfinity
Documentation CD for instructions on viewing the Event log.
Ethernet transmit/receive activity light: When this green light is on, there is
activity between the server and the network.
System error light: This amber light is on when a system error occurs. A light on
the diagnostics LED panel will also be on to further isolate the error. (For more
information, see the User’s Reference on the IBM Netfinity Documentation CD.)
Ethernet-link status light: When this green light is on, there is an active
connection on the Ethernet port.
Ethernet speed 100 Mbps: When this green light is on, the Ethernet speed is
100 Mbps. When the light is off, the Ethernet speed is 10 Mbps.
20
IBM® Netfinity® 7600 Installation Guide
Chapter 4. Configuring your server
The ServerGuide CDs provide software setup tools and installation tools that are
specifically designed for your IBM Netfinity server. Use these CDs during the initial
installation of your server to configure basic hardware features and to simplify your
network operating system installation. (See “Using the ServerGuide CDs” for more
information.) The ServerGuide CDs also contain a collection of application programs,
which you can install after your server is up and running.
In addition to the ServerGuide CDs, you can use the following configuration
programs to customize your server hardware:
•
Configuration/Setup Utility
The Configuration/Setup Utility program is part of the basic input/output system
(BIOS) code that comes with your server. You can use this program to configure
serial and parallel port assignments, change interrupt request (IRQ) settings,
change the drive startup sequence, set the date and time, and set passwords.
•
SCSISelect Utility
With the built-in SCSISelect Utility program, you can configure the devices that
are attached to the integrated SCSI controller. Use this program to change
default values, resolve configuration conflicts, and perform a low-level format
on a SCSI hard disk drive.
•
ServeRAID programs
Your server comes with a ServeRAID adapter installed. You must use the
ServeRAID configuration program to define and configure your disk-array
subsystem before you install your operating system.
Attention: Refer to the User’s Reference on the IBM Netfinity Documentation CD for
detailed instructions for using the configuration programs and ServerGuide CDs.
Using the ServerGuide CDs
The ServerGuide CDs provide state-of-the-art programs to detect the server model
and hardware options that are installed, configure Netfinity server hardware, provide
device drivers, and install your network operating system (NOS).
Note:
If the ServerGuide CD does not start, see “ServerGuide startup problems” on
page 26.
1. Insert the Netfinity Setup and Installation CD, and restart the server.
2. Follow the instructions on the screens to:
a. Select your language.
b. Select your keyboard layout and country.
c. View the Overview to learn about ServerGuide features.
d. View the README file to review installation tips about your NOS and
adapter.
e. Start the setup and hardware configuration programs.
f. Start the NOS installation. You will need your copy of the NOS CD.
Note:
© Copyright IBM Corp. 2000
For information on the supported NOS versions, refer to the Netfinity
Setup and Installation CD label.
21
After installing the NOS
Be sure to take advantage of the following additional software that is included with
the ServerGuide package:
•
Operating System Updates CDs — include selected NOS updates that are
provided by NOS software developers.
•
Netfinity Applications CDs — include powerful applications that are ready to
install; their use requires no software keys.
Note:
See the CD labels for a current list of updates and applications or start
the Netfinity Applications and view the online overview.
Netfinity systems management solutions
Your IBM Netfinity server includes the Advanced System Management Processor.
This systems management subsystem monitors your Netfinity server and notifies you
when problems occur. It performs automated actions if specified thresholds are
reached and enables you to resolve system problems remotely (using a serial or
Advanced System Management Interconnect connection), even if the server is
powered down or the operating system has locked up.
Your server comes with the IBM Netfinity Manager™ program and Client Services for
Netfinity Manager version 5.2
Some versions of the ServerGuide package contain the IBM Netfinity Manager
software. For information about how to install applications that are included in the
ServerGuide package, see the ServerGuide information.
IBM Netfinity Manager is a comprehensive set of hardware management utilities.
These utilities enable you to manage industry-standard, Intel-processor-based, server,
desktop, workstation, and notebook systems over network operating systems from
Microsoft, SCO, Novell, and IBM. These utilities support multiple protocols,
including TCP/IP, IPX, NetBIOS, SNA, SLIP, and HTTP. This robust set of systems
management software tools delivers comprehensive local and remote system control
over the entire life cycle of the system.
22
IBM® Netfinity® 7600 Installation Guide
Chapter 5. Solving problems
sme lborp gnivloS
This section provides basic troubleshooting information to help you resolve some
common problems that might occur while setting up your server.
If you cannot locate and correct the problem using the information in this section,
refer to the " Solving problems" section on the IBM Netfinity Documentation CD and the
"Support for Netfinity Servers" flowchart in the front of this booklet.
POST beep code descriptions
snoi tpi rcsed edoc pe b tsoP
POST emits one beep to signal successful completion. If POST detects a problem
during startup, other beep codes might occur. You can use the following beep code
descriptions to help identify and resolve problems that are detected during startup.
Note:
See the "Solving problems" section of the User’s Reference on the IBM Netfinity
Documentation CD for more information about the POST beep codes.
Beep code
Descriptions of the POST beep codes
No beep
Call for service.
Continuous
If no video appears, the startup microprocessor failed. Verify that the startup
microprocessor is installed correctly. If it is, replace the startup microprocessor. If the
problem persists, call for service.
One short
POST completed successfully. One beep also occurs after POST if you enter an incorrect
password.
Two short
Follow the instructions that appear on the screen.
Three short
POST detected a system memory error. Verify that the memory is installed correctly. If it
is, replace the failing memory module.
Repeating
short
The system board might contain a failing component.
1. Verify that the keyboard and pointing devices are connected properly.
2. Ensure that nothing is resting on the keyboard.
3. Disconnect the pointing device; then, restart the server. If the problem goes away,
replace the pointing device. If the problem remains, call for service.
One long and
one short
If the video controller on the system board is being used, call for service. If you installed
an optional video adapter, replace the failing adapter
One long and
two short
A video I/O adapter ROM is not readable, or the video subsystem is defective. If you
installed an optional video adapter, replace the failing adapter. If the problem remains,
call for service.
One long and
three short
The system-board video subsystem has not detected a monitor connection to the server.
Ensure that the monitor is connected to the server. If the problem persists, replace the
monitor.
Table 3. POST beep code descriptions
© Copyright IBM Corp. 2000
23
Post error messages
Beep code
Two long
and two
short
All other
beep codes
Descriptions of the POST beep codes
POST does not support the optional video adapter. Replace the optional video adapter
with one that is supported by the server or use the integrated video controller.
1. Verify that the system memory modules are installed correctly.
2. Tun off the server; then, restart the server. If the problem remains, call for service.
Table 3. POST beep code descriptions
POST error messages
segas em ror e t soP
The following table provides an abbreviated list of the error messages that might
appear during POST.
Note:
24
See the "Solving problems" section of the User’s Reference on the IBM Netfinity
Documentation CD for more information about the POST beep codes.
IBM® Netfinity® 7600 Installation Guide
Post error messages
POST message
Failing device or problem
found
Suggested action
129
L1 cache of a microprocessor
Check the installation of your microprocessors.
162
Change in device configuration
Verify that your optional devices are turned on and
installed correctly.
163
Time of day has not been set
Set the correct date and time.
164
Change in memory
configuration
Verify that your memory is installed properly; then,
restart the server and run the Configuration/Setup
Utility program.
201
Change in memory
configuration
Verify that your memory is fully seated and installed
properly.
229
L2 cache of a microprocessor
Check the installation of your microprocessors.
289
Failing DIMM was disabled
Verify that your memory is correct for your server
and that it is installed properly.
301
Keyboard and keyboard
controller
Ensure that the keyboard cable is connected and
nothing is resting on the keyboard keys.
962
Parallel port configuration error
Start the Configuration/Setup program and verify
that the parallel-port setting is correct.
11xx
Serial port error
Verify that the serial cable is connected correctly.
1162
Serial port configuration conflict
Start the Configuration/Setup program and ensure
that the IRQ and I/O port assignments needed by
the serial port are available.
1601
BIOS update needed
Download and install the latest system BIOS level.
1800
PCI adapter hardware interrupt
Start the Configuration/Setup program and verify
that the interrupt resource settings are correct.
2400
Video controller and memory
Verify that the monitor is connected correctly.
00019xxx
Processor x is not functioning or
failed the built-in test
Verify that processor x is installed correctly. If the
problem remains, replace processor x.
00180xxx
A PCI adapter requested a
resource that is not available
Start the Configuration/Setup program and ensure
that the resources needed by the PCI adapter are
available.
012980xx
Data for processor x
Download and install the latest system BIOS level.
01298200
Microprocessor speed mismatch
Install microprocessors with identical speeds.
I9990305
POST could not find an
operating system.
Install your operating system.
303
2462
012981xx
Table 4. Abbreviated list of POST error messages
Chapter 5. Solving problems
25
ServerGuide startup problems
ServerGuide startup problems
sme lborp putrats ediuGrevreS
Look for the symptom in the left column of the chart. Probable solutions to the
problem are in the right column.
Setup
Netfinity Setup
and Installation
CD won’t start.
Suggested action
•
Be sure the system is a supported Netfinity server with a
startable (bootable) CD-ROM drive.
•
If the startup (boot) sequence settings have been altered, be
sure the CD-ROM is first in the boot sequence.
•
If more than one CD-ROM drive is installed, be sure that
only one drive is set as the primary drive. Start the CD
from the primary drive.
ServeRAID
•
program cannot
view all installed •
drives - or cannot install
NOS.
Be sure there are no duplicate SCSI IDs or IRQ
assignments.
Be sure that the hard disk drive is connected properly.
The Operating
System
Installation
program
continuously
loops.
Free up more space on the hard disk.
ServerGuide
won't start your
NOS CD.
Be sure the NOS CD you have is supported by ServerGuide. See
the Netfinity Setup and Installation CD label for a list of NOS
versions supported.
Can't install NOS Either there is no logical drive defined (ServeRAID systems) or
- option is
the ServerGuide system partition is not present. Run the setup
grayed out.
and configuration program.
TechConnect
CD
Can't start
TechConnect
CD.
Be sure you're starting the CD on a system with Microsoft
Windows installed.
Can't view
publications
from
TechConnect
CD, or text is
unreadable.
Be sure you have the Adobe reader installed (available from the
TechConnect CD).
Diskette Factory
CD
Get "time out" or
"Unknown host"
errors
26
Suggested action
IBM® Netfinity® 7600 Installation Guide
Suggested action
Be sure you have access to the Internet through FTP directly.
Troubleshooting chart
Troubleshooting chart
t rahc gnitohselbuorT
Notes:
1. Refer to the "Solving problems" section of the User’s Reference on the IBM Netfinity
Documentation CD for more detailed troubleshooting charts.
2. If you cannot find the problem in the troubleshooting charts, run the diagnostic
programs. If you have run the diagnostic test programs, or if running the tests
does not reveal the problem, call for service.
Monitor problems
Testing
Suggested action
Some IBM monitors have their own self-tests. If you suspect a problem with
your monitor, refer to the information that comes with the monitor for
adjusting and testing instructions.
If you still cannot find the problem, call for service.
The screen is blank.
Verify that:
1. The server power cord is plugged into the server and a working
electrical outlet.
2. The monitor cables are connected properly.
3. The monitor is turned on, and the Brightness and Contrast controls are
adjusted correctly.
If the items above are correct and the screen remains blank, call for service.
Only the cursor appears.
Call for service.
The monitor works when
you turn on the server, but
goes blank when you start
some application programs.
Verify that:
1. The primary monitor cable is connected to the video port.
2. You installed the necessary device drivers for the applications.
If the items above are correct and the screen remains blank, call for service.
Wavy, unreadable, rolling,
distorted screen, or screen
jitter.
If the monitor self-tests show the monitor is OK, consider the location of the
monitor. Magnetic fields around other devices (such as transformers,
appliances, fluorescent lights, and other monitors) can cause screen jitter or
wavy, unreadable, rolling, or distorted screen images. If this happens, turn
off the monitor. (Moving a color monitor while it is turned on might cause
screen discoloration.) Then move the device and the monitor at least 305
mm (12 in.) apart. Turn on the monitor.
Notes:
1. To prevent diskette drive read/write errors, be sure the distance
between monitors and diskette drives is at least 76 mm (3 in.).
2. Non-IBM monitor cables might cause unpredictable problems.
3. An enhanced monitor cable with additional shielding is available for
the 9521 and 9527 monitors. For information about the enhanced
monitor cable, see your IBM reseller or IBM marketing representative.
If the problem remains, call for service.
Wrong characters appear on
the screen.
If the wrong language is displayed, update the BIOS with the correct
language.
If the problem remains, call for service.
Chapter 5. Solving problems
27
Troubleshooting chart
Power problems
The server does not power
on.
Suggested action
Verify that:
1. The power cables are properly connected to the server.
2. The electrical outlet functions properly.
3. The type of memory that is installed is correct.
4. If you just installed an option, remove it, and restart the server. If the
server now powers on, you might have installed more options than the
power supply can support.
5. The LEDs on the power supply are on.
If the problem remains, call for service.
Microprocessor problems
The server emits a
continuous tone during
POST.
Suggested action
The startup (boot) microprocessor is not working properly.
Verify that the startup microprocessor is seated properly. If it is, replace the
startup microprocessor.
If the problem remains, call for service.
Memory problems
Suggested action
The amount of memory
Verify that:
displayed is less than the
1. The memory modules are seated properly.
amount of memory installed.
2. You have installed the correct type of memory.
3. If you changed the memory, you updated the memory configuration
using the Configuration/Setup Utility program.
4. All banks of memory on the DIMMs are enabled. The server might
have detected a problem and automatically disabled a DIMM bank, or a
DIMM bank could have been manually disabled.
If the above items are correct, run the memory-diagnostic program. The
system might have detected a bad memory module and automatically
reallocated memory to enable you to continue to operate. If the memory
tests fail, call for service or replace the failing DIMM.
28
IBM® Netfinity® 7600 Installation Guide
Troubleshooting chart
Option problems
An IBM option that was just
installed does not work.
Suggested action
Verify that:
1. The server supports the option. Refer to the "Support for Netfinity
Servers" flowchart for information about obtaining ServerProven™
compatibility information from the World Wide Web.
2. You followed the installation instructions that came with the option.
3. The option is installed correctly.
4. You have not loosened any other installed options or cables.
5. You updated the configuration information using the
Configuration/Setup Utility program. Whenever memory or an option
is changed, you must update the configuration.
If the problem remains, call for service.
Expansion enclosure
problems
The SCSI expansion
enclosure used to work, but
does not work now.
Suggested action
Verify that:
1. The cables for all external SCSI options are connected correctly.
2. The last option in each SCSI chain, or the end of the SCSI cable, is
terminated correctly.
3. Any external SCSI option is turned on. You must turn on an external
SCSI option before turning on the server.
For more information, see the documentation for your SCSI options and
expansion enclosure.
Service processor problems
Netfinity Service Processor
Manager reports a general
monitor failure
Suggested action
Disconnect the server from all electrical sources, wait for 30 seconds,
reconnect the server to the electrical sources, and restart the server.
If a problem remains, call for service.
Chapter 5. Solving problems
29
Troubleshooting chart
30
IBM® Netfinity® 7600 Installation Guide
Appendix A. Product warranties and notices
This chapter contains warranty and emission notices. It also contains trademarks and
general-information notices.
Warranty Statements
The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by
country. Part 2 is the same for all countries. Be sure to read both the Part 1 that applies
to your country and Part 2.
•
United States, Puerto Rico, and Canada (Z125-4753-05 11/97)
(Part 1 - General Terms)
•
Worldwide except Canada, Puerto Rico, Turkey, and United States (Z125-569701 11/97)
(“Part 1 - General Terms,” on page 34)
•
Worldwide Country-Unique Terms
(“Part 2 - Worldwide Country-Unique Terms” on page 36)
IBM Statement of Limited Warranty for United States,
Puerto Rico, and Canada (Part 1 - General Terms)
This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 Country-unique Terms. The terms of Part 2 may replace or modify those of Part
1.The warranties provided by IBM in this Statement of Limited Warranty apply only
to Machines you purchase for your use, and not for resale, from IBM or your reseller.
The term "Machine" means an IBM machine, its features, conversions, upgrades,
elements, or accessories, or any combination of them. The term "Machine" does not
include any software programs, whether pre-loaded with the Machine, installed
subsequently or otherwise. Unless IBM specifies otherwise, the following warranties
apply only in the country where you acquire the Machine. Nothing in this Statement
of Warranty affects any statutory rights of consumers that cannot be waived or limited
by contract. If you have any questions, contact IBM or your reseller.
Machine - Netfinity 7600
Warranty Period* - Three Years
*Contact your place of purchase for warranty service information. Some IBM
Machines are eligible for On-site warranty service depending on the country where
service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and workmanship
and 2) conforms to IBM's Official Published Specifications. The warranty period for a
Machine is a specified, fixed period commencing on its Date of Installation. The date
on your sales receipt is the Date of Installation, unless IBM or your reseller informs
you otherwise.
© Copyright IBM Corp. 2000
31
During the warranty period IBM or your reseller, if approved by IBM to provide
warranty service, will provide repair and exchange service for the Machine, without
charge, under the type of service designated for the Machine and will manage and
install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and IBM or
your reseller are unable to either 1) make it do so or 2) replace it with one that is at
least functionally equivalent, you may return it to your place of purchase and your
money will be refunded. The replacement may not be new, but will be in good
working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
improper maintenance by you, or failure caused by a product for which IBM is not
responsible. The warranty is voided by removal or alteration of Machine or parts
identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION
TO JURISDICTION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO
THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN
THAT EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such as
assistance via telephone with "how-to" questions and those regarding Machine set-up
and installation, will be provided WITHOUT WARRANTIES OF ANY KIND.
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. In the
United States, call IBM at 1-800-772-2227. In Canada, call IBM at 1-800-565-3344. You
may be required to present proof of purchase.
IBM or your reseller provides certain types of repair and exchange service, either at
your location or at a service center, to keep Machines in, or restore them to,
conformance with their Specifications. IBM or your reseller will inform you of the
available types of service for a Machine based on its country of installation. IBM may
repair the failing Machine or exchange it at its discretion.
When warranty service involves the exchange of a Machine or part, the item IBM or
your reseller replaces becomes its property and the replacement becomes yours. You
represent that all removed items are genuine and unaltered. The replacement may
not be new, but will be in good working order and at least functionally equivalent to
the item replaced. The replacement assumes the warranty service status of the
replaced item.
Any feature, conversion, or upgrade IBM or your reseller services must be installed on
a Machine which is 1) for certain Machines, the designated, serial-numbered Machine
and 2) at an engineering-change level compatible with the feature, conversion, or
32
IBM® Netfinity® 7600 Installation Guide
upgrade. Many features, conversions, or upgrades involve the removal of parts and
their return to IBM. A part that replaces a removed part will assume the warranty
service status of the removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that prevent
its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s
possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential, proprietary
or personal information contained in a Machine which you return to IBM or your
reseller for any reason. You should remove all such information from the Machine
prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In some
cases, the Machine may not be new and may have been previously installed.
Regardless of the Machine’s production status, IBM’s appropriate warranty terms
apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other liability,
you are entitled to recover damages from IBM. In each such instance, regardless of
the basis on which you are entitled to claim damages from IBM (including
fundamental breach, negligence, misrepresentation, or other contract or tort claim),
IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000
(or equivalent in local currency) or the charges (if recurring, 12 months’ charges
apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF,
OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL, INCIDENTAL,
OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF IBM, ITS
SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
Appendix A. Product warranties and notices
33
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
IBM Statement of Warranty Worldwide except Canada,
Puerto Rico, Turkey, United States (Part 1 – General
Terms)
This Statement of Warranty includes Part 1 - General Terms and Part 2 - Countryunique Terms. The terms of Part 2 may replace or modify those of Part 1. The
warranties provided by IBM in this Statement of Warranty apply only to Machines
you purchase for your use, and not for resale, from IBM or your reseller. The term
"Machine" means an IBM machine, its features, conversions, upgrades, elements, or
accessories, or any combination of them. The term "Machine" does not include any
software programs, whether pre-loaded with the Machine, installed subsequently or
otherwise. Unless IBM specifies otherwise, the following warranties apply only in the
country where you acquire the Machine. Nothing in this Statement of Warranty
affects any statutory rights of consumers that cannot be waived or limited by contract.
If you have any questions, contact IBM or your reseller.
Machine - Netfinity 7600
Warranty Period* - Three Years
*Contact your place of purchase for warranty service information. Some IBM
Machines are eligible for On-site warranty service depending on the country where
service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and workmanship
and 2) conforms to IBM’s Official Published Specifications. The warranty period for a
Machine is a specified, fixed period commencing on its Date of Installation. The date
on your sales receipt is the Date of Installation, unless IBM or your reseller informs
you otherwise.
During the warranty period IBM or your reseller, if approved by IBM to provide
warranty service, will provide repair and exchange service for the Machine, without
charge, under the type of service designated for the Machine and will manage and
install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and IBM or
your reseller are unable to either 1) make it do so or 2) replace it with one that is at
least functionally equivalent, you may return it to your place of purchase and your
money will be refunded. The replacement may not be new, but will be in good
working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
improper maintenance by you, or failure caused by a product for which IBM is not
responsible. The warranty is voided by removal or alteration of Machine or parts
identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
34
IBM® Netfinity® 7600 Installation Guide
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION
TO JURISDICTION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO
THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN
THAT EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such as
assistance via telephone with "how-to" questions and those regarding Machine set-up
and installation, will be provided WITHOUT WARRANTIES OF ANY KIND.
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. You may be
required to present proof of purchase.
IBM or your reseller provides certain types of repair and exchange service, either at
your location or at a service center, to keep Machines in, or restore them to,
conformance with their Specifications. IBM or your reseller will inform you of the
available types of service for a Machine based on its country of installation. IBM may
repair the failing Machine or exchange it at its discretion.
When warranty service involves the exchange of a Machine or part, the item IBM or
your reseller replaces becomes its property and the replacement becomes yours. You
represent that all removed items are genuine and unaltered. The replacement may
not be new, but will be in good working order and at least functionally equivalent to
the item replaced. The replacement assumes the warranty service status of the
replaced item.
Any feature, conversion, or upgrade IBM or your reseller services must be installed on
a Machine which is 1) for certain Machines, the designated, serial-numbered Machine
and 2) at an engineering-change level compatible with the feature, conversion, or
upgrade. Many features, conversions, or upgrades involve the removal of parts and
their return to IBM. A part that replaces a removed part will assume the warranty
service status of the removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that prevent
its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
Appendix A. Product warranties and notices
35
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s
possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential, proprietary
or personal information contained in a Machine which you return to IBM or your
reseller for any reason. You should remove all such information from the Machine
prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In some
cases, the Machine may not be new and may have been previously installed.
Regardless of the Machine’s production status, IBM’s appropriate warranty terms
apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other liability,
you are entitled to recover damages from IBM. In each such instance, regardless of
the basis on which you are entitled to claim damages from IBM (including
fundamental breach, negligence, misrepresentation, or other contract or tort claim),
IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000
(or equivalent in local currency) or the charges (if recurring, 12 months’ charges
apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF,
OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL, INCIDENTAL,
OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF IBM, ITS
SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Part 2 - Worldwide Country-Unique Terms
ASIA PACIFIC
AUSTRALIA: The IBM Warranty for Machines: The following paragraph is added
to this Section:
The warranties specified in this Section are in addition to any rights you may have
under the Trade Practices Act 1974 or other legislation and are only limited to the
extent permitted by the applicable legislation.
Extent of Warranty: The following replaces the first and second sentences of this
Section:
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
operation in other than the Specified Operating Environment, improper maintenance
by you, or failure caused by a product for which IBM is not responsible.
36
IBM® Netfinity® 7600 Installation Guide
Limitation of Liability: The following is added to this Section:
Where IBM is in breach of a condition or warranty implied by the Trade Practices Act
1974, IBM’s liability is limited to the repair or replacement of the goods or the supply
of equivalent goods. Where that condition or warranty relates to right to sell, quiet
possession or clear title, or the goods are of a kind ordinarily acquired for personal,
domestic or household use or consumption, then none of the limitations in this
paragraph apply.
PEOPLE’S REPUBLIC OF CHINA: Governing Law: The following is added to this
Statement:
The laws of the State of New York govern this Statement.
INDIA: Limitation of Liability: The following replaces items 1 and 2 of this Section:
1. liability for bodily injury (including death) or damage to real property and
tangible personal property will be limited to that caused by IBM’s negligence;
2. as to any other actual damage arising in any situation involving nonperformance
by IBM pursuant to, or in any way related to the subject of this Statement of
Warranty, IBM’s liability will be limited to the charge paid by you for the
individual Machine that is the subject of the claim.
NEW ZEALAND: The IBM Warranty for Machines: The following paragraph is
added to this Section:
The warranties specified in this Section are in addition to any rights you may have
under the Consumer Guarantees Act 1993 or other legislation which cannot be
excluded or limited. The Consumer Guarantees Act 1993 will not apply in respect of
any goods which IBM provides, if you require the goods for the purposes of a
business as defined in that Act.
Limitation of Liability: The following is added to this Section:
Where Machines are not acquired for the purposes of a business as defined in the
Consumer Guarantees Act 1993, the limitations in this Section are subject to the
limitations in that Act.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
The following terms apply to all EMEA countries.
The terms of this Statement of Warranty apply to Machines purchased from an IBM
reseller. If you purchased this Machine from IBM, the terms and conditions of the
applicable IBM agreement prevail over this warranty statement.
Warranty Service
If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or United Kingdom, you
may obtain warranty service for that Machine in any of those countries from either (1)
an IBM reseller approved to perform warranty service or (2) from IBM.
If you purchased an IBM Personal Computer Machine in Albania, Armenia, Belarus,
Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary,
Kazakhstan, Kirghizia, Federal Republic of Yugoslavia, Former Yugoslav Republic of
Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia,
or Ukraine, you may obtain warranty service for that Machine in any of those
countries from either (1) an IBM reseller approved to perform warranty service or (2)
from IBM.
The applicable laws, Country-unique terms and competent court for this Statement
are those of the country in which the warranty service is being provided. However,
Appendix A. Product warranties and notices
37
the laws of Austria govern this Statement if the warranty service is provided in
Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech
Republic, Federal Republic of Yugoslavia, Georgia, Hungary, Kazakhstan, Kirghizia,
Former Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania,
Russia, Slovak Republic, Slovenia, and Ukraine.
The following terms apply to the country specified:
EGYPT: Limitation of Liability: The following replaces item 2 in this Section:
2. as to any other actual direct damages, IBM’s liability will be limited to the total
amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
FRANCE: Limitation of Liability: The following replaces the second sentence of the
first paragraph of this Section:
In such instances, regardless of the basis on which you are entitled to claim damages
from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
GERMANY: The IBM Warranty for Machines: The following replaces the first
sentence of the first paragraph of this Section:
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this Section:
The minimum warranty period for Machines is six months.
In case IBM or your reseller are unable to repair an IBM Machine, you can
alternatively ask for a partial refund as far as justified by the reduced value of the
unrepaired Machine or ask for a cancellation of the respective agreement for such
Machine and get your money refunded.
Extent of Warranty: The second paragraph does not apply.
Warranty Service: The following is added to this Section:
During the warranty period, transportation for delivery of the failing Machine to IBM
will be at IBM’s expense.
Production Status: The following paragraph replaces this Section:
Each Machine is newly manufactured. It may incorporate in addition to new parts, reused parts as well.
Limitation of Liability: The following is added to this Section:
The limitations and exclusions specified in the Statement of Warranty will not apply
to damages caused by IBM with fraud or gross negligence and for express warranty.
In item 2, replace "U.S. $100,000" with "1.000.000 DEM."
The following sentence is added to the end of the first paragraph of item 2:
IBM’s liability under this item is limited to the violation of essential contractual terms
in cases of ordinary negligence.
IRELAND: Extent of Warranty: The following is added to this Section:
Except as expressly provided in these terms and conditions, all statutory conditions,
including all warranties implied, but without prejudice to the generality of the
foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of Goods
and Supply of Services Act 1980 are hereby excluded.
Limitation of Liability: The following replaces items one and two of the first
paragraph of this Section:
1. death or personal injury or physical damage to your real property solely caused by
IBM’s negligence; and 2. the amount of any other actual direct damages, up to the
38
IBM® Netfinity® 7600 Installation Guide
greater of Irish Pounds 75,000 or 125 percent of the charges (if recurring, the 12
months’ charges apply) for the Machine that is the subject of the claim or which
otherwise gives rise to the claim.
Applicability of suppliers and resellers (unchanged).
The following paragraph is added at the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in respect of
any default shall be limited to damages.
ITALY: Limitation of Liability: The following replaces the second sentence in the first
paragraph:
In each such instance unless otherwise provided by mandatory law, IBM is liable for
no more than: (item 1 unchanged) 2)as to any other actual damage arising in all
situations involving non-performance by IBM pursuant to, or in any way related to
the subject matter of this Statement of Warranty, IBM’s liability, will be limited to the
total amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
The following replaces the second paragraph of this Section:
Unless otherwise provided by mandatory law, IBM and your reseller are not liable for
any of the following: (items 1 and 2 unchanged) 3) indirect damages, even if IBM or
your reseller is informed of their possibility.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND:
Limitation of Liability: The following is added to this Section:
IBM’s entire liability to you for actual damages arising in all situations involving
nonperformance by IBM in respect of the subject matter of this Statement of Warranty
will be limited to the charge paid by you for the individual Machine that is the subject
of your claim from IBM.
TURKIYE: Production Status: The following replaces this Section:
IBM fulfills customer orders for IBM Machines as newly manufactured in accordance
with IBM’s production standards.
UNITED KINGDOM: Limitation of Liability: The following replaces items 1 and 2
of the first paragraph of this Section:
1. death or personal injury or physical damage to your real property solely caused by
IBM’s negligence; 2. the amount of any other actual direct damages or loss, up to the
greater of Pounds Sterling 150,000 or 125 percent of the charges (if recurring, the 12
months’ charges apply) for the Machine that is the subject of the claim or which
otherwise gives rise to the claim.
The following item is added to this paragraph:
3. breach of IBM’s obligations implied by Section 12 of the Sale of Goods Act 1979 or
Section 2 of the Supply of Goods and Services Act 1982.
Applicability of suppliers and resellers (unchanged).
The following is added to the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in respect of
any default will be limited to damages.
NORTH AMERICA
CANADA: Warranty Service: The following is added to this section:
To obtain warranty service from IBM, call 1-800-565-3344.
UNITED STATES OF AMERICA: Warranty Service: The following is added to this
section:
To obtain warranty service from IBM, call 1-800-772-2227.
Appendix A. Product warranties and notices
39
Notices
References in this publication to IBM products, programs, or services do not imply
that IBM intends to make these available in all countries in which IBM operates. Any
reference to an IBM product, program, or service is not intended to state or imply that
only that IBM product, program, or service may be used. Subject to IBM’s valid
intellectual property or other legally protectable rights, any functionally equivalent
product, program, or service may be used instead of the IBM product, program, or
service. The evaluation and verification of operation in conjunction with other
products, except those expressly designated by IBM, are the responsibility of the user.
IBM may have patents or pending patent applications covering subject matter in this
document. The furnishing of this document does not give you any license to these
patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
This section contains trademarks, electronic emission notices, and other important
information.
Any references in this publication to non-IBM Web sites are provided for convenience
only and do not in any manner serve as an endorsement of those Web sites. The
materials at those Web sites are not part of the materials for this IBM product and use
of those Web sites is at your own risk.
Edition Notice
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements
and/or changes in the product(s) and/or the program(s) described in this publication
at any time.
This publication was developed for products and services offered in the United States
of America and the United Kingdom. It is possible that this publication may contain
reference to, or information about, IBM products (machines and programs),
programming, or services that are not announced in your country. Such references or
information must not be construed to mean that IBM intends to announce such IBM
products, programming, or services in your country.
Requests for technical information about IBM products should be made to your IBM
reseller or IBM marketing representative. No part of this publication may be
reproduced or distributed in any form or by any means without prior permission in
writing from the International Business Machines Corporation.
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION,
2000. All rights reserved.
40
IBM® Netfinity® 7600 Installation Guide
Note to U.S. Government Users — Documentation related to restricted rights — Use,
duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule
Contract with IBM Corp.
Year 2000 readiness and instructions
This is a Year 2000 Readiness Disclosure.
A product is Year 2000 Ready if the product, when used in accordance with its
associated documentation, is capable of correctly processing, providing and/or
receiving date data within and between the 20th and 21st centuries, provided all other
products (for example, software, hardware, and firmware) used with the product
properly exchange date data with it.
This IBM PC hardware product has been designed to process four-digit date
information correctly within and between the 20th and 21st centuries. If your IBM
computer is on when the century changes, you should turn it off and then back on
again once, or restart the operating system, to ensure that the internal clock resets
itself for the new century.
This IBM PC product cannot prevent errors that might occur if software you use or
exchange data with is not ready for the Year 2000. IBM software that comes with this
product is Year 2000 Ready. However, software from other companies might come
with this IBM PC product. IBM cannot take responsibility for the readiness of that
software. You should contact the software developers directly if you wish to verify
readiness, understand limitations, or look for any software updates.
To learn more about IBM PC products and the Year 2000, visit our Web site at
http://www.ibm.com/pc/year2000. The information and tools there can help you
with your Year 2000 transition plan, especially if you have multiple IBM PCs. IBM
encourages you to check periodically for updated information.
Trademarks
The following terms are trademarks of the IBM Corporation in the United States or
other countries or both:
Alert on LAN
OS/2 Warp
Aptiva
PC Server
Chipkill
PC 300
DB2
Predictive Failure Analysis
EtherJet
ServeRAID
HelpCenter
ServerGuide
HelpWare
ServerProven
IBM
SurePath
IntelliStation
TechConnect
Netfinity
ThinkPad
Netfinity Advanced System Management
Update Connector
Netfinity Manager
ValuePoint
OS/2
Wake on LAN
Appendix A. Product warranties and notices
41
Lotus and Domino are trademarks of Lotus Development Corporation in the United
States, other countries, or both.
Tivoli and NetView are trademarks of Tivoli Systems Inc. in the United States, other
countries, or both.
Intel, MMX, LANDesk, Pentium, Pentium II Xeon, and Pentium III Xeon are
trademarks or registered trademarks of Intel Corporation in the United States, other
countries, or both.
Microsoft, Windows, and Windows NT are trademarks or registered trademarks of
Microsoft Corporation.
UNIX is a registered trademark in the United States and other countries and is
licensed exclusively through The Open Group.
Java and all Java-based trademarks and logos are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States, other countries, or both.
Other company, product, and service names may be trademarks or service marks of
others.
Important notes
Processor speeds indicate the internal clock speed of the microprocessor; other factors
also affect application performance.
When referring to hard disk drive capacity, MB stands for 1000000 bytes and GB
stands for 1000000000 bytes. Total user-accessible capacity may vary depending on
operating environments.
Maximum internal hard disk drive capacities assume the replacement of any standard
hard disk drives and population of all hard disk drive bays with the largest currently
supported drives available from IBM.
Unless otherwise stated, IBM makes no representations or warranties with respect to
non-IBM products. Support (if any) for the non-IBM products is provided by the third
party, not IBM.
Some software may differ from its retail version (if available), and may not include
user manuals or all program functionality.
Electronic emission notices
Federal Communications Commission (FCC)
Statement
Federal Communications Commission (FCC) Class A Statement
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
42
IBM® Netfinity® 7600 Installation Guide
Properly shielded and grounded cables and connectors must be used in order to meet
FCC emission limits. IBM is not responsible for any radio or television interference
caused by using other than recommended cables and connectors or by unauthorized
changes or modifications to this equipment. Unauthorized changes or modifications
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A emission compliance
statement
Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard
entitled Digital Apparatus, ICES-003 of the Department of Communications.
Avis de conformité aux normes du ministère des Communications du Canada
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel brouiller:
Appareils Numériques, NMB-003 édictée par le ministre des Communications.
Australia and New Zealand Class A statement
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety
requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for
indirect connection to public telecommunication systems in the United Kingdom.
European community directive conformance statement
This product is in conformity with the protection requirements of EC Council
Directive 89/336/EEC on the approximation of the laws of the Member States relating
to electro-magnetic compatibility.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Appendix A. Product warranties and notices
43
Taiwan electrical emission statement
Japanese Voluntary Control Council for Interference
(VCCI) statement
Power cords
For your safety, IBM provides a power cord with a grounded attachment plug to use
with this IBM product. To avoid electrical shock, always use the power cord and plug
with a properly grounded outlet.
IBM power cords used in the United States and Canada are listed by Underwriter’s
Laboratories (UL) and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified cord
set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a
maximum of 15 feet in length and a parallel blade, grounding-type attachment plug
rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSAcertified cord set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor
cord, a maximum of 15 feet in length and a tandem blade, grounding-type attachment
plug rated 15 amperes, 250 volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a
grounding-type attachment plug. The cord set should have the appropriate safety
approvals for the country in which the equipment will be installed.
IBM power cords for a specific country or region are usually available only in that
country or region.
44
IBM® Netfinity® 7600 Installation Guide
IBM power cord part
number
Used in these countries and regions
13F9940
Argentina, Australia, China (PRC), New Zealand, Papua New Guinea, Paraguay,
Uruguay, Western Samoa
13F9979
Afghanistan, Algeria, Andorra, Angola, Austria, Belgium, Benin, Bulgaria, Burkina
Faso, Burundi, Cameroon, Central African Rep., Chad, Czech Republic, Egypt,
Finland, France, French Guiana, Germany, Greece, Guinea, Hungary, Iceland,
Indonesia, Iran, Ivory Coast, Jordan, Lebanon, Luxembourg, Macau, Malagasy,
Mali, Martinique, Mauritania, Mauritius, Monaco, Morocco, Mozambique,
Netherlands, New Caledonia, Niger, Norway, Poland, Portugal, Romania, Senegal,
Slovakia, Spain, Sudan, Sweden, Syria, Togo, Tunisia, Turkey, former USSR,
Vietnam, former Yugoslavia, Zaire, Zimbabwe
13F9997
Denmark
14F0015
Bangladesh, Burma, Pakistan, South Africa, Sri Lanka
14F0033
Antigua, Bahrain, Brunei, Channel Islands, Cyprus, Dubai, Fiji, Ghana, Hong
Kong, India, Iraq, Ireland, Kenya, Kuwait, Malawi, Malaysia, Malta, Nepal,
Nigeria, Polynesia, Qatar, Sierra Leone, Singapore, Tanzania, Uganda, United
Kingdom, Yemen, Zambia
14F0051
Liechtenstein, Switzerland
14F0069
Chile, Ethiopia, Italy, Libya, Somalia
14F0087
Israel
1838574
Thailand
62X1045
Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman Islands, Colombia,
Costa Rica, Dominican Republic, Ecuador, El Salvador, Guatemala, Guyana, Haiti,
Honduras, Jamaica, Japan, Korea (South), Liberia, Mexico, Netherlands Antilles,
Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Suriname, Taiwan, Trinidad
(West Indies), United States of America, Venezuela
Appendix A. Product warranties and notices
45
46
IBM® Netfinity® 7600 Installation Guide
Index
A
I
S
acoustical noise emissions 2
adapter
installing 7
adapters 7
important notes 42
information LED panel 19
information light 20
safety information
electrical vii, x
laser products viii
lifting server 15
safety requirements
electronic emission Class A notice 42
FCC Class A notice 42
SCSISelect Utility program 21
ServeRAID Configuration program
L
B
beep codes 23
C
CD-ROM 2
Class A electronic emission notice
42
components
color 4
major 4
Configuration/Setup Utility program 21
configuring your server 21
D
diskette drive 2
documentation CD 1
E
electrical input 2
electronic emission Class A notice
42
environment 2
error messages
POST 24
Ethernet link status light 20
Ethernet transmit/receive activity
light 20
F
FCC Class A notice 42
H
heat output 2
hot-swap drive 12
specifications 2
LEDs
front of server 20
hard disk drive 20
M
21
major components 4
memory 10
installing 10
specifications 2
microprocessor 13
specifications 2
ServerGuide
CDs 21
error symptoms 26
size 2
specifications 2
system error light 20
system power light 20
systems management 22
N
T
non-hot-swap drive
specifications 2
NOS See operating system
notices
electronic emission, Class A 42
FCC, Class A 42
miscellaneous 42
product 42
trademarks 41
trademarks 41
troubleshooting chart 27
turning off the server 18
O
V
operating system, installing 21
video 2
voltage regulator module 13
VRM 13
P
U
United States electronic emission
Class A notice 42
United States FCC Class A notice 42
PCI expansion slots 2
power control button 18
power cords 44
power supply
installing 14
specifications 2
problems, solving 23
product
notices 42
W
R
year 2000 readiness and instructions
Web site 1
weight 2
working with the server with the
power on 7
Y
41
reset button 18
47
48
IBM® Netfinity® 7600 Installation Guide
IBM
Part Number:
09N8216
SC09-N821-60
*07SC09N82160*
0409N8216
09N8216
Printed in the United States of America
on recycled paper containing 10&
recovered post-consumer fiber.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement