Quick Reference Guide (Download PDF, 2.77M)

Quick Reference Guide (Download PDF, 2.77M)
2015 Infiniti Q50
Hybrid
Quick Reference Guide
2
4
3
1
7
6
6
10
11
Behind
steering wheel
17
Behind
5 steering wheel
8
9
12
13
19
18
18
20
21
16
22
14
22
15
23
24
VEHICLE INFORMATION DISPLAY
1 13 TILT AND TELESCOPIC STEERING COLUMN*
2 LOW TIRE PRESSURE WARNING LIGHT
14 VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH*
HEADLIGHT AND TURN SIGNAL CONTROL
3 EV INDICATOR LIGHT*
4 PUSH BUTTON IGNITION SWITCH
5 6 PADDLE SHIFTERS*
ASSIST CHARGE GAUGE
7 WINDSHIELD WIPER AND WASHER SWITCH
8 9 INTELLIGENT CRUISE CONTROL/CRUISE
CONTROL/DRIVER’S ASSISTANCE SWITCHES
10 STEERING WHEEL SWITCHES FOR
AUDIO*/BLUETOOTH®
11 INSTRUMENT BRIGHTNESS CONTROL*/
TRIP RESET SWITCH
12 VEHICLE INFORMATION DISPLAY SWITCHES
*See your Owner’s Manual for information.
15 TRUNK RELEASE SWITCH
16 HOOD RELEASE*
17 UPPER DISPLAY
18 CLIMATE CONTROL SWITCHES
19 LOWER DISPLAY
20 AUDIO SYSTEM
21 FRONT PASSENGER AIR BAG
STATUS LIGHT*
22 HEATED SEAT SWITCHES
23 INFINITI CONTROLLER
24 DRIVE MODE SWITCH*
table of contents
new system features
INFINITI Connection™ (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Approaching Vehicle Sound for Pedestrians (VSP) System . . . . . . . . . . . . . 3
Main Interface Switches Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Around View® Monitor (AVM) with Moving Object Detection (MOD)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SiriusXM Travel Link and SiriusXM Traffic (if so equipped) . . . . . . . . . . . . . 6
essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator . . . . 7
Hybrid Awareness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Direct Response Hybrid™ System Warning Light . . . . . . . . . . . . . . . . . . . . . . 8
Loose Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fuel-filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lower Display Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Driving Aids (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Active Lane Control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Heated Steering Wheel (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
first drive features
INFINITI Intelligent Key System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Trunk Lid Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Heated Seats (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatic Drive Positioner (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 13
Assist Charge Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Outside Mirror Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Starting/Stopping the Hybrid System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Windshield Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Climate Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FM/AM/HD Radio®/SiriusXM® Satellite Radio (if so equipped) . . . . . . . . . 19
USB (Universal Serial Bus) Connection Port/iPod® Interface . . . . . . . . . . . 20
Conventional (Fixed Speed) Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . 20
Intelligent Cruise Control (ICC) System (if so equipped) . . . . . . . . . . . . . . . . . . . 21
system guide
Vehicle Information Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
HomeLink® Universal Transceiver (if so equipped) . . . . . . . . . . . . . . . . . . 26
Please see your Owner’s Manual for important safety information
and system operation limitations.
• A cellular telephone should not be used for any purpose while
driving so full attention may be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
• Children 12 and under should always ride in the rear seat
properly secured in child restraints or seat belts according to
their age and weight.
• Do not drink and drive.
For more information, refer to your InTouch Owner’s Manual,
the “Safety –– Seats, seat belts and supplemental restraint
system (section 1)” and the “Starting and driving (section 5)”
of your Owner’s Manual.
Additional information about your vehicle is also available in your Owner’s
Manual, Navigation System Owner’s Manual and at www.InfinitiUSA.com.
To view detailed
instructional videos, go to
www.infinitiownersinfo.mobi/2015/q50
or snap this barcode with an
appropriate barcode reader.
new s y s te m f e a t u r e s
INFINITI Connection™* (if so equipped)
INFINITI Connection™ combines personalized
convenience, concierge settings and personal security
features to compliment the Total Ownership Experience.
For more details on INFINITI Connection or to enroll your
vehicle, please visit www.Infiniticonnection.com
or call 855-444-7244.
Available services include:
INFINITI Personal Assistant – To access INFINITI Personal Assistant, select “Connect to
Voice Menu” from the INFINITI Connection menu or touch the
key on the map screen.
At the voice prompt, say “INFINITI Personal Assistant” to be connected.
• Your INFINITI Personal Assistant can send destination information directly to your vehicle.
• Automatic Collision Notification – In case of air bag deployment, a signal is sent
containing the vehicle location and customer information to a Response Specialist who
notifies the proper authorities.
Emergency Call – This service provides emergency
assistance by connecting the subscriber to an
INFINITI Connection Specialist.
• In case of an emergency, press the in-vehicle
telematics SOS button 1 .
• A Response Specialist will provide assistance
based on the situation described by the vehicle’s occupant.
1
Enhanced Roadside Assistance – Roadside Assistance can be accessed by touching
the INFINITI Connection key on the Info menu, the
key on the map screen or by
pressing the SOS button 1 .
• This service allows subscribers to receive assistance for a non-emergency incident, such
as towing, or a third party response.
• If warranted, Roadside Assistance may also be used in conjunction with the Emergency
Assistance service by pressing the SOS button 1 .
My Schedule – Access your personal online Google Calendar™, hear details read via text-tospeech** and select location as a destination via the navigation system.
Report Stolen Vehicle – A Response Specialist will attempt to obtain location information
from a reported stolen vehicle and provide that information to local law enforcement
agencies to assist in the recovery of your stolen vehicle.
Remote Door Lock/Unlock – Remotely access your vehicle via a INFINITI Connection
Response Specialist or designated website to remotely lock or unlock your vehicle.
Alarm Notification – This system will notify you when the factory-installed vehicle alarm
system has been activated.
Scheduled Maintenance Notification – Receive scheduled maintenance notifications based
on mileage data provided by your vehicle.
*Infiniti Connection™ is only available on vehicles equipped with an optional Infiniti Connection™ subscription service.
**Laws in some communities may restrict the use of text-to-speech. Check local regulations before using this feature.
2
Maintenance Alert – Receive notification of a vehicle system malfunction that triggers
instrument panel warning lights.
Destination Assistance – Receive point-of-interest assistance via guided IVR (Interactive
Voice Response) or a Response Specialist by pressing the
key on the map screen or the
INFINITI Connection™ web portal.
Destination Send-to-Vehicle – Find and download point-of interest information from
Google Maps™. To access, go to the INFINITI Connection menu and select “Sync All
Information Feeds”. Then go to the feeds menu page and download the desired
destination information.
Connected Search – Select “Connected Search” from the Destination menu on the vehicle’s
navigation system to conduct a point-of-interest search within a certain distance of the
vehicle’s location.
Drive Zone – Monitor the movement of your vehicle within a specified region. Set up
boundaries in the Monitoring section of the INFINITI Connection web portal.
Max Speed Alert – Set up a maximum speed on the INFINITI Connection web portal. You
will receive notifications if your vehicle exceeds the max speed setting.
obile Information Service – Receive the latest news headlines, stock quotes and sports
M
scores by setting up preferences on the Mobile Information Service page in the INFINITI
Connection web portal.
Valet Alert – Use Valet Alert to set up a 0.2 mile radius around your vehicle.
• Activate alerts by pressing the “Connect to Voice Menu” button on the INFINITI
Connection screen or by pressing the
key on the map screen.
• At the prompt, say “Valet Alert” and then “Activate” or “Deactivate”.
For more information, refer to the “Viewing technical information (section 7)” of your Navigation System Owner’s Manual.
Approaching Vehicle Sound for Pedestrians (VSP) System
The VSP system helps alert pedestrians to the presence of the vehicle when it is being driven
at a low speed.
When the vehicle starts to move, it produces a sound. The sound stops when the vehicle
speed reaches approximately 19 mph (30 km/h) while accelerating.
This sound will activate again when decelerating to a speed less than 16 mph (25 km/h).
For more information, refer to the “Hybrid System Overview” section of your Owner’s Manual.
Main Interface Switches Overview
1 AUDIO – Press to navigate to the main audio screen.
From here, all of the audio functions
can be accessed.
2 MENU – Press to navigate to the main menu
1
2
3
screen. From here, there is access to the navigation
functions and all the applications, including the settings application.
3 CLIMATE – Press to navigate to the CLIMATE controls screen. From here, you have access
to climate control, heated steering wheel and heated seat functions.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
3
new s y s te m f e a t u r e s
User Registration
Driving positions, navigation, climate controls, etc.,
can be memorized for each user.
To register a new user:
1. Press the MENU button. The menu screen will appear.
2. Touch the right arrow key until Edit User
is displayed. The, touch Edit User.
3. Touch User List.
4. Touch Add New. From here, you can edit Name and Picture.
5. Touch OK when finished.
For more information, refer to the “Information and settings (section 8)” of your InTouch Owner’s Manual.
Upper Display
The upper display is controlled by the touch-screen,
INFINITI controller and the
switch on the
steering wheel.
Press OK 1 on the INFINITI controller or OK on the
steering wheel switch to display the menu screen.
From here, you are able to choose from audio
sources, map settings, hands-free phonebook and
adding new options.
Use the dial on the INFINITI controller to move the
cursor, and press OK 1 to select an item.
3
1
2
While on the map screen, use the INFINITI controller
to navigate to another location on the map by sliding
the controller in the direction you would like to go.
Press the
button 2 to return to the previous page.
MAP AND DISPLAY VIEW (with Navigation)
There are different variations of split screen views that can be displayed on the upper
display. The map is always displayed on the right-hand side of the screen. Some of the left
side options are turn list, intersection and turn by turn.
To customize the split screen views on the upper display:
1. When the current location map screen is displayed, press the MAP/VOICE 3 button on
the INFINITI controller and the display view bar will appear at the bottom of the screen.
2. Touch an icon on the display view bar, or use the dial on the INFINITI controller to scroll
through the possible options and press OK 1 to select one.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
4
Around View® Monitor (AVM) with Moving Object Detection (MOD)
(if so equipped)
With the ignition switch in the ON position, the
Around View Monitor is activated by pressing the
CAMERA button 1 , located on the control panel,
or by moving the shift lever to the R (REVERSE)
position. The control panel displays various views of
the position of the vehicle.
1
When the shift lever is in the P (PARK), N (NEUTRAL)
or D (DRIVE) position and the CAMERA button 1 is
pressed, the following views will display in order:
Start from any Control Panel screen
Front view and bird’s-eye view
Press
Press
Press
Front wide view
Front view and front-side view
Press
When the shift lever is in the R (REVERSE) position and the CAMERA button 1 is pressed,
the following views will display in order:
Rear view and bird’s-eye view
Rear view and front-side view
Press
Rear wide view
Press
Press
5
new s y s te m f e a t u r e s
The colored guide lines on the display screen indicate vehicle width and approximate
distances to objects with reference to the vehicle body line.
•R
ed 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft
(2 m) and 10 ft (3 m).
There are some areas where the system will not show objects.
•W
hen in the front or the rear view display, an
object below the bumper or on the ground may
not be viewed 2 .
•W
hen in the bird’s-eye view, a tall object near the
seam of the camera viewing areas 3 will not
appear in the monitor.
3
The distance between objects viewed on the AVM differs from the actual distance.
Objects in the bird’s-eye view will appear further than the actual distance.
MOVING OBJECT DETECTION (MOD)
If the MOD system detects moving objects
surrounding the vehicle, a yellow frame 4 will
be displayed on the camera image and a chime
will sound.
In the bird’s-eye view, a yellow frame is displayed
on those camera images (front, rear, right, left)
where moving objects are detected.
When the following are displayed:
5
6
4
7
•B
lue MOD icon 5 ; the system is operative in this view.
•G
ray MOD icon 6 ; the system is not operative in this view.
• N
o MOD icon; the system is off.
To temporarily turn the system on or off, touch the Sonar-MOD key 7 .
For more information, refer to the “Monitor system (section 7)” of your InTouch Owner’s Manual.
SiriusXM Travel Link* and SiriusXM Traffic* (if so equipped)
Your vehicle’s Navigation System is equipped with
SiriusXM Travel Link and SiriusXM Traffic capabilities.
SiriusXM Travel Link provides access to real-time
weather information and forecasts, nearby fuel
prices, movie listings and stock quotes.
SiriusXM Traffic provides information that may
help to avoid delays due to traffic incidents. Traffic
jams, roadwork, road closures around the current
location, etc., are represented graphically on the
map by icons depicting the nature of the event.
Incidents on the route are automatically displayed
when they are approached.
*These features, SiriusXM® Satellite Radio, Travel Link and Traffic, require
an active subscription. Multiple subscriptions may be necessary to activate
the various features.
For more information, refer to the “Navigation (section 4)” and the “General system information (section 6)” of your
6 Navigation System Owner’s Manual.
2
e s s e n t i a l i n f or mat ion
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Flat Tire Visit Dealer or Tire Pressure Low — Add
Air warning message will appear in the vehicle
information display 1 and the low tire pressure
warning light 2 will illuminate when one or more
tires are low in pressure and air is needed.
• T he tire pressures should be checked when
the tires are cold. The tires are considered cold
after the vehicle has been parked for 3 hours
or more or driven less than 1 mi (1.6 km) at
moderate speeds.
1
2
When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tire to the recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire, and within a few seconds, the hazard warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once and the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.
After tire pressures are adjusted, drive the vehicle at speeds above 16 mph (25 km/h). The
Flat Tire Visit Dealer or Tire Pressure Low — Add Air warning message and low tire pressure
warning light will extinguish.
When the low tire pressure warning light flashes for 1 minute and then remains on, the
TPMS is not functioning properly. Have the system checked by an INFINITI retailer.
Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the
outside temperature. Low outside temperature can lower the temperature of the air inside
the tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure
warning light to illuminate. If the warning light illuminates, check the tire pressure in your tires.
•C
heck the tire pressure (including the spare tire) often and always prior to long
distance trips.
The Tire and Loading Information label contains valuable information. Please refer to
“Technical and consumer information (section 9)” in your Owner’s Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
7
essent i al i n f o r m a t i o n
Hybrid Awareness
Your vehicle is virtually silent in the electric mode. If you exit your vehicle while it is ON but the
engine is not running, the engine will automatically start, informing you that the car is still ON.
Do not store your INFINITI Intelligent Key within the detection range of the vehicle. This may
cause welcome lights and other functions to activate, creating unwanted battery drain.
The hybrid system is designed for optimum efficiency and performance. Activation of the
electric mode may vary with driving conditions and driver input. A full battery display does
not indicate the vehicle should be in the electric mode.
The ready to drive
indicator light illuminates when the hybrid system is powered and the
vehicle may be driven.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Direct Response Hybrid™ System Warning Light
This light will illuminate when the ignition switch is in the ON position
and will extinguish when the hybrid system is started.
The light will also illuminate when a malfunction occurs in the electric
motor or hybrid system.
When this light illuminates while driving, immediately stop the vehicle in a safe location and
contact an INFINITI retailer.
If the hybrid system warning light blinks while driving, it may indicate that the Li-ion battery
charge is low and you cannot continue to drive.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the vehicle information display 1 when the fuel-filler
cap is not tightened correctly.
1
To tighten, turn the cap clockwise until a single click
is heard.
The warning message will extinguish when the
vehicle detects the fuel-filler cap is properly tightened
and the
or
button 2 is pressed.
If the cap is not properly tightened, the Malfunction
Indicator Light
may illuminate.
2
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
8
Fuel-filler Door
The fuel-filler door is located on the passenger, rear
side of the vehicle.
Ensure that at least the driver’s door is unlocked.
Push and release the left side of the fuel-filler door
to open.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
Lower Display Maintenance
Only use a microfiber cloth to clean the lower display.
For more information, refer to the “Appearance and care (section 7)” of your Owner’s Manual.
Driving Aids (if so equipped)
The trip computer displays different driving aids, including Forward Emergency Braking,
Lane Departure Prevention and Blind Spot Intervention if they are currently activated.
To disable driving aids or warnings:
1. Press the MENU button just below the lower display.
2. Touch the right arrow key until you see Driver
Assistance. Touch the Driver Assistance key.
3. Touch the key that corresponds with the
driving aid or warning you would like to turn off
(Forward Assist, Lane Assist or Blind Spot Assist).
4. Select the driving aid line key to disable.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Active Lane Control (if so equipped)
Active Lane Control slightly corrects front tire angles and steering wheel torque, allowing
the driver to make fewer steering wheel corrections.
Active Lane Control is active when:
• T he vehicle is driven at speeds of approximately 45 mph (70 km/h) and above.
• T he Lane Departure Prevention and Active Lane Control systems are enabled in the
Settings menu.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
9
essent i al i n f o r m a t i o n
Heated Steering Wheel (if so equipped)
The heated steering wheel system is designed to operate only when the surface
temperature of the steering wheel is below approximately 68°F (20°C). The steering wheel
heater will also turn off automatically after approximately 30 minutes.
To manually turn on the heated steering wheel, touch the steering wheel heater icon 1
within the CLIMATE control screen in the lower display. The indicator light will illuminate.
AUTOMATIC STEERING WHEEL HEATER
When turned on, the steering wheel heater will
automatically heat the steering wheel whenever the
temperature inside the vehicle compartment is below
approximately 68°F (20°C) at the time of pushing the
ignition to the ON position. The temperature of the
steering wheel will also fluctuate while turned on.
1
To turn on the automatic steering wheel heater:
1. P
ress the MENU button just below the lower display.
2. Touch the Settings key.
3. Touch the right arrow key until you see Others.
Touch the Others key.
4. Touch Climate.
5. Touch Auto Steering Wheel Heater 2 to turn it on.
2
For more information, refer to the “Heater and air conditioner (section 3)” of your InTouch Owner’s Manual.
Clock Set/Adjustment
To adjust the time and the appearance of the clock on the display:
1. Press the Menu button under the lower touch-screen display.
2. Touch the Settings key.
3. Locate and touch the Clock key.
The following settings can be adjusted:
On-Screen Clock: Set the clock display on or off.
When this item is on, the clock display appears.
Daylight Savings Time: The application of daylight
savings time can be turned to ON, OFF or AUTO.
2
1
C
lock Format (24h): The clock can be set to 12 hour or 24 hour times. When the indicator
light illuminates, the clock is set to the 24-hour format.
Time Zone: Adjust the time zone. Choose a time zone from the available list. Press the
button to return to the previous screen.
Offset Adjustment: The time can be adjusted forward or backward by minutes 1
and/or hours 2 . The current clock time can be set up for a difference of 12 hours and
59 minutes.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
10
f i r s t d r i v e f e at ur e s
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the engine. It is
important to make sure the Intelligent Key is with you (that
is, in your pocket or purse).
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
LOCKING AND UNLOCKING DOORS
Using Intelligent Key:
• Touch the inside of the door handle 1 to unlock the
corresponding front door.
• Pressing the request switch 2 while touching the
inside of the door handle will unlock the rest of
the doors.
• To lock the vehicle, push either door handle request
switch 3 once.
• Change vehicle settings to unlock all doors by touching the inside of
the door handle 1 . For more information, refer to the “Information
and settings (section 8)” of your Owner’s Manual.
Using Key Fob:
• Press the
button 5 on the key fob to unlock the driver’s door.
• Press the
button 5 again; all other doors will unlock.
• Press the
button 4 on the key fob.
To release the trunk lid, press the
button 6 for more than
1 second. Lift the trunk lid to access the trunk.
1
2
3
4
5
6
7
The Intelligent Key can also be used to activate the panic alarm by
pressing and holding the button 7 for more than 1 second. Once
activated, the panic alarm and headlights will stay on for a period of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is discharged
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key,
and a chime will sound.
4. Within 10 seconds after the chime sounds, push
the ignition switch while depressing the brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
11
f i rst dr i v e f e a t u r e s
Trunk Lid Release
Using the Intelligent Key while in your pocket
or purse:
•Push the trunk open request switch 1 for
more than 1 second while carrying the INFINITI
Intelligent Key with you.
1
Using the Intelligent Key Fob:
•Press the trunk button HOLD on the Intelligent Key
for more than 1 second.
•Push the truck request switch 1 while all of the
doors are unlocked.
Using the Trunk Lid release switch on the
instrument panel:
•From inside the vehicle, push down on the trunk
lid release switch 2 on the instrument panel.
2
3
To completely disable all power to the trunk lid,
push the trunk release power cancel switch 3
located in the glove box to the OFF position. While
in this position, the trunk lid cannot be opened with the trunk open
request switch 1 , trunk button
or the trunk lid release switch 2 .
HOLD
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Seat Adjustments
POWER SEAT ADJUSTMENTS
To slide the seat forward or backward, push the switch
1 forward or backward.
To recline the seatback, push the switch
forward or backward.
2
4
5
3
1
2
SEAT LIFTER
To adjust the angle of the front portion or height of the seat, push the front or rear end of the
switch
1 up or down.
POWER LUMBAR SUPPORT (if so equipped)
To adjust the seat lumbar support, push the front or back end of the switch
3 .
MANUAL LUMBAR SUPPORT (if so equipped)
To adjust the seat lumbar support, move the lever up or down.
SIDE SUPPORT (driver’s seat only) (if so equipped)
The driver’s seat side support adjusts the support on your torso.
Push the switch 4 away from you to loosen the support, or pull the switch 4 toward you for
more support.
MANUAL THIGH EXTENSION (if so equipped)
To slide the thigh extension forward or backward, pull up on the lever 5 under the front of the
seat and slide forward or backward. Release the lever to lock the seat in position.
For more information, refer to the “Safety – Seats, seat belts and supplemental restraint system (section 1)” of your Owner’s Manual.
12
Heated Seats (if so equipped)
There are 2 ways to operate the heated seats:
2
2
1. Press the heated seat switch 1 .
• Every
press of the switch allows you to cycle
through the 5 different modes of
AUTO – High – Mid – Low – OFF.
3
2. While on the CLIMATE control screen on the lower
display, touch the left or right heated seat icon 2 .
• The Left or Right Heater Settings screen is
displayed with a list of the 5 different modes of
AUTO – High – Mid – Low – OFF to choose from.
1
1
• T he indicator light on the heated seat switch
1 will illuminate when the system is in AUTO – High – Mid – Low.
•W
hile in AUTO, the heated seats will turn on and off automatically, depending on
temperature conditions in the vehicle compartment.
• T o view which of the 5 modes the system is in, press the CLIMATE button 3 . This will
bring up the CLIMATE control screen on the lower display. From here, you will see the
heated seat icons 2 for the driver’s and passenger’s side, and below the icon is the
mode the system is in currently.
For more information, refer to the “Heater and air conditioner (section 3)” of your InTouch Owner’s Manual.
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.
Follow this procedure to set the memory positions:
•C
onfirm the shift lever is in the P (PARK) position.
•P
ush the ignition switch to the ON position.
•A
djust the driver’s seat, steering column and outside mirrors to the desired positions
using the adjusting switches for each feature.
•P
ush the SET switch and within 5 seconds push the memory switch (1 or 2) for at
least 1 second.
• T he indicator light on the memory switch you select will illuminate for approximately
5 seconds and a buzzer will sound.
• T he driver’s seat, steering column and outside mirror positions are now set to
your preferences.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
13
f i rst dr i v e f e a t u r e s
Assist Charge Gauge
This shows the power consumed 2 or generated
1 by the electric motor.
1
2
For more information, refer to the “Hybrid System Overview” and the
“Instruments and controls (section 2)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch 1 right or left.
Adjust each mirror to the desired position using
the switch 2 .
1
2
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirrors surfaces downward to provide
better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the R (REVERSE) position.
3. Choose the right or left outside mirror by operating the outside mirror control switch.
4. The outside mirrors surfaces move downward.
Both outside mirror surfaces will return to their original positions when one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) position.
• The ignition switch is placed in the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Hybrid System
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP button to start
the hybrid system.
TURNING THE HYBRID SYSTEM OFF
Move the shift lever to the P (PARK) position and apply the parking brake.
Press the ignition switch START/STOP button to turn the hybrid system off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
14
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 1 to turn on the front parking, side
marker, tail, license plate and instrument panel lights. Turn the switch to the
position
2 to turn on the headlights.
AUTOLIGHT SYSTEM
The autolight system will automatically turn the
headlights on when it is dark and off when it is light.
The system will keep the headlights on for a period
of time after you turn the ignition off and all doors
are closed.
3
1
2
To activate the autolight system, turn the headlight control switch to the AUTO position 3
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF position,
position 1 or
position 2 .
HIGH BEAM SELECT
To manually select the high beam function:
1. Turn the headlight control switch to the
position 2 .
2. P
ush the headlight control switch 4 forward to select the high beam function. The blue
indicator light
illuminates in the instrument panel. Pull the headlight switch back to
the original position to select the low beam. The blue indicator light will extinguish.
Pull and release the headlight control switch 5 to flash the headlight high beams on and off.
HIGH BEAM ASSIST
The High Beam Assist system will operate when the vehicle is driven at approximately
22 mph (35 km/h) and above. If an oncoming vehicle or leading vehicle appears in front of
your vehicle when the high beam is on, the headlights will automatically be switched to the
low beam.
Following the procedure below only activates the High Beam Assist system. This does not
necessarily turn on the high beam even if there is no other traffic. Both ambient light and
traffic conditions have to be correct for the high beam to illuminate.
To activate High Beam Assist, turn the headlight
control switch to the AUTO position 3 and push the
headlight control switch 4 forward to turn on the
high beam. The high beam
assist indicator light
will illuminate.
4
5
FOG LIGHT SWITCH
The headlights must be on and the low beams
selected for the fog lights to operate.
Turn the switch (inside collar) to the
to turn the fog lights on.
position 6
Turn the switch (inside collar) to the OFF position to
turn the fog lights off.
6
15
f i rst dr i v e f e a t u r e s
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to flash, but the lever does not latch,
to signal a lane change. Hold the lever until the lane change is completed.
Move the lever up or down until the turn signal begins to flash, but the lever does not latch,
and release the lever. The turn signal will automatically flash three times.
Choose the appropriate method to signal a lane change based on road and traffic conditions.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Windshield Wiper and Washer Switch
RAIN-SENSING AUTO WIPER SYSTEM (if so equipped)
Move the lever to one of the following positions to
operate the windshield wipers:
1 Mist (MIST) – One sweep operation of the wipers.
2 Auto (AUTO) – Operates the rain-sensing wipers
MIST 1
3
OFF
AUTO 2
LO 4
HI 5
intermittently. The intermittent speed can be
adjusted by twisting the time control ring 3
to increase or decrease wiper sensitivity.
4 Low (LO) – Wipers operate at a continuous
5 High (HI) – Wipers operate at a continuous
6 Pull the lever toward you to activate the washer. The wipers will operate several times.
low-speed.
6
high-speed.
PULLING UP THE WIPER ARM
The wiper arm should be in the up position when
replacing the wiper.
To pull up the wiper arm, push the wiper switch
to the MIST 1 position twice when the ignition
switch is in the OFF position within 1 minute. The
wiper operation stops in mid-operation and the
wiper arm can be pulled up.
The shift lever should be in the P (PARK) position.
To return the wiper arm, place the wiper arm in the
down position and operate the wiper switch once.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
16
6
3
2
4
8
5
11
10
4
9
7
12
6
1
13
Climate Controls
1 CLIMATE BUTTON
Press to display the CLIMATE control screen on the lower display.
2 DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS
Press the driver’s side temperature control buttons up for warmer air or down
for cooler air.
3 PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS
To manually adjust the passenger’s side temperature, press the passenger’s side
temperature control buttons up for warmer air or down for cooler air.
4 FAN SPEED CONTROL
To manually adjust the fan speed, press the
button or touch the
key to increase
the fan speed. Press the button or touch the
key to decrease the fan speed.
5 AUTO BUTTON
Press the AUTO button to turn the system on, and the system will automatically control
the inside temperature (automatic cooling and/or dehumidified heating), air flow
distribution and fan speed.
6 MODE CONTROL BUTTON
Press the
button or touch the
the following air flow outlets:
key in the center of the lower display to cycle through
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
17
f i rst dr i v e f e a t u r e s
7 AUTO AIR RECIRCULATION KEY (if so equipped)
Touch to allow inside air recirculation and outside air circulation to switch automatically
depending on the quality of the outside air.
8 INTAKE AIR CONTROL BUTTON
Pressing the intake air control button
will cancel auto air recirculation 7 (if so
equipped) until it is re-activated from the touch-screen (see above). Press the intake
air control button
to manually control whether the interior air is recirculated
or outside air is drawn into the vehicle. When the indicator light is on, interior air is
recirculated, outside odors are avoided and the interior vehicle temperature is most
effectively maintained.
The air recirculation mode cannot be activated when the climate control system is in the
front defroster mode
or the front defroster foot vent mode .
9 A/C KEY
Touch the A/C key to turn the air conditioner system on or off. This system helps cool and
dehumidify the air inside the cabin and defog the windows.
10 DUAL KEY
Touch to turn the passenger’s side temperature controls on or off. When the system
is on, the indicator light will illuminate. This function will allow the passenger’s side
temperature to be adjusted independently from the driver’s side by pressing the
passenger’s side temperature control buttons 3 .
11 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the defroster button
to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This features removes humidity from the air.
T o defrost the front and side windows, set the driver’s side temperature controls 2 and
fan speed controls 4 to their maximum settings.
12 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS
Push the Rear window and outside mirror defroster switch
This function automatically turns off after approximately 15 minutes.
to turn the system on or off.
13 ON/OFF BUTTON
Press the ON/OFF button to turn the climate control system on or off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual and the “Heater and Air
Conditioner (section 3)” of your InTouch Owner’s Manual.
18
7
8
8
1
2
3
5
6
4
FM/AM/HD Radio®/SiriusXM®* Satellite Radio (if so equipped)
1 AUDIO BUTTON
Press to display the AUDIO screen on the lower display.
(power) BUTTON/VOL (volume) CONTROL KNOB
Press the (power) button to turn the system on or off.
Turn the VOL (volume) control knob right or left to increase or decrease the volume.
SEEK•CAT/TRACK
BUTTON
To scan quickly through each broadcasting station, press the SEEK•CAT/TRACK button to
stop at the previous or next broadcast station.
For satellite radio, press the SEEK•CAT/TRACK button to switch to the first channel of the
previous or next category.
For HD Radio®, press the SEEK•CAT/TRACK button to change the station.
Press the SEEK•CAT/TRACK button to change tracks on a CD.
Press and hold the SEEK•CAT/TRACK button to rewind or fast forward a track on a CD.
TUNE•CH/FOLDER BUTTON
To manually tune the radio, press the TUNE•CH/FOLDER button left or right.
Press and hold the TUNE•CH/FOLDER button left or right to accelerate radio tuning.
RADIO BUTTON
Press to the radio band in the order of AM, FM and satellite radio.
2 3
4
5
6 DISC•AUX BUTTON
Press to change the audio source (CD, iPod®, USB, Bluetooth® Streaming Audio or AUX).
7 STATION PRESET KEYS
Up to 36 stations/channels can be set for AM, FM and satellite radio.
To store a station in a preset, you must first select a radio band by pressing the RADIO
button then tune to the desired AM, FM or satellite radio station.
Now select and hold the desired station memory key (1-36) until the preset number is
updated on the display and a beep is heard. Programing is now complete.
To retrieve a previously set station, press the arrow right or left 8 and touch the memory
key (1-36) that contains the stored station/channel you wish to listen to.
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional satellite radio subscription service.
For more information, refer to the “Audio system (section 4)” of your InTouch Owner’s Manual.
19
f i rst dr i v e f e a t u r e s
USB (Universal Serial Bus) Connection Port/iPod® Interface
The USB port 1 is located in the center console
under the armrest.
When a compatible USB memory device or iPod® is
plugged into the USB port:
2
1
• A confirmation message appears. Select “Yes”
if you prefer to use the devices with Voice
Recognition in which song titles and artist names are registered in the system.
•C
ompatible audio files stored on the device can be played through the vehicle’s audio
system and front display.
If two USB devices are plugged in at the same time, you are able to use Voice
Recognition to choose which one should play. Just press the
button on the steering
wheel to activate Voice Recognition and follow the voice prompts.
This vehicle is equipped with Audio and Video RCA inputs 2 . This will allow you to play
audio and video through your vehicle from an external source.
For more information, refer to the “Getting Started (section 2)”, the “Audio system (section 4)” and the “Voice recognition
(section 10)” of your InTouch Owner’s Manual.
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a constant cruising speed once the vehicle has
reached 25 mph (40 km/h).
The system will automatically maintain the set speed until you tap the brake pedal,
accelerate, cancel or turn the system off.
To activate the cruise control, push the ON/OFF switch. The CRUISE indicator light in the
instrument panel will illuminate.
To set a cruising speed, accelerate the vehicle to the desired speed, push the SET – switch and
release. The CRUISE SET indicator light in the instrument panel will illuminate. Take your foot
off the accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the RES + switch. When the vehicle
attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the SET – switch. Release the switch when
the vehicle slows to the desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch.
To turn off cruise control, push the ON/OFF switch. The CRUISE indicator light in the
instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
20
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
4
To set vehicle-to-vehicle distance control mode,
press the
button 1 for less than 1.5 seconds.
The gray
indicator light 2 will illuminate.
7
8
3
1
Accelerate to the desired speed.
Push down on the SET – switch 3 and release it.
Intelligent Cruise Control will be set to the
desired speed.
Press the distance button 4 repeatedly to change
the set distance between long, middle and short.
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate 5 in set mode.
2
5
When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate 6 in
set mode.
To reset at a faster cruising speed, push up and
hold the RES + switch 7 . When the vehicle attains
the desired speed, release the switch.
6
To reset at a slower cruising speed, push down and
hold the SET – switch 3 . Release the switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch 8 . The set vehicle speed indicator
5 will change to grey.
To turn off Intelligent Cruise Control, press the
the instrument panel will extinguish.
button 1 . The
indicator light 2 in
To set conventional (fixed speed) cruise control mode:
While Intelligent Cruise Control is off, press the
button 1 and hold it down for more
than 1.5 seconds. The grey
indicator light will illuminate.
Accelerate to the desired speed.
Push down on the SET – switch and release it. The green
Cruise control should be set to the desired speed.
indicator light will illuminate.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
21
syste m g ui d e
Vehicle Information Display
When the
or
button 1 is pressed,
the following modes will appear on the vehicle
information display 2 :
1
•
Fuel Economy – Displays the current
fuel consumption.
2
•
Average Speed – Displays the average vehicle
speed since the last reset.
•
Distance/Time – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
•RANGE – Displays the estimated distance to empty
(dte) the vehicle can be driven before refueling.
3
•
Navigation (if so equipped) – Displays the
navigation route information when route guidance is set in the navigation system.
• Audio – Displays the status of the audio information.
• Driving Aids (if so equipped) – Displays driving aid status.
• Tire Pressure (if so equipped) – Displays the current tire pressure in each tire.
• Chassis Control – Displays the status of Active Lane Control and Active Trace Control.
•
Energy Flow - Displays the energy flow between the engine and the Li-ion battery and the
current charge level of the battery.
• EV Odometer - This indicates the total distance traveled using the electric motor only.
•
Acceleration Guide - Displays how efficiently the vehicle is being driven based on the
accelerator pedal position.
• Coolant Temp - Displays the current temperature of the coolant.
• Warning – Displays when a warning is present.
Push the TRIP RESET switch 3 for approximately 1 second to reset the currently displayed
trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Bluetooth® Hands-free Phone System
A cellular telephone should not be used while driving
so full attention may be given to vehicle operation.*
Bluetooth® Controls
SYSTEM OPERATING TIPS
Press the button on the steering wheel to activate
voice recognition.
Press the button to interrupt the voice prompts at
any time and speak a command after the tone.
To use the system faster, you may speak the second
level commands with the main menu command on the
main menu.
*Some jurisdictions prohibit the use of cellular telephones while driving.
22
Microphone
To decrease or increase the volume of the voice prompts, push the volume control
switches or on the steering wheel or turn the (power) button/ VOL (volume) control
knob on the audio system while the system is responding.
The Voice Recognition system allows you to choose between voice input and manual
controls of lists. Choose the method that is easiest for you. For example, when a list is
shown, you can use the
switch and push the OK switch on the steering wheel to
select an item from the displayed list instead of saying the item.
When using the
feature to navigate lists during Voice Recognition, use the spoken
menu readout feature to help navigate the list easily. Voice input is paused when menu
control is activated. To resume Voice Recognition, select a menu item by pushing the
switch or simply push the button.
R
educe background noise as much as possible by closing windows and pointing HVAC vents
away from the ceiling.
After the tone, speak naturally without long pauses and without raising your voice.
When speaking phonebook names, use full name (e.g. Michael Smith) or first
name (e.g. Michael).
T o cancel a Voice Recognition session, say “Exit” or press and hold the
for 5 seconds.
button
To go back to the previous command, say “Go back”.
F or more detailed information and instructions, refer to your cellular phone’s Owner’s Manual and
visit www.InfinitiUSA.com/bluetooth.
CONNECTING PROCEDURE
The vehicle must be stationary when
connecting the phone.
1.Press the MENU button below the lower display and
touch the Settings key.
2.Touch Bluetooth.
3.Touch Connect Device and then touch Add New.
4. Initiate connecting from the phone.
• T he connecting procedure varies according
to each cellular phone model. For detailed
connecting instructions and a list of compatible
phones, please visit
www.InfinitiUSA.com/bluetooth.
• W
hen prompted for a PIN, enter the PIN that
appears on the screen into the handset.
5. When connecting is complete, the screen will return
to the previous screen.
23
syste m g ui d e
PHONEBOOK SETUP
Depending on your cellular phone, the system may automatically download your cellular
phone’s entire phonebook to the vehicle’s Bluetooth® system.
If the phonebook does not download automatically, the vehicle’s phonebook may be set up for
manual entry.
To manually download entries:
1.Press the MENU button below the lower display.
2.Touch the Settings key.
3.Touch Phone/Mail key.
4.Touch Phone Settings key.
5.Touch Phonebook/Favorites Settings key.
6.Touch Configure Phonebook Settings key.
7.Touch Manual Phonebook Transfer key.
• From here, you are able to transfer information
from your cellular phone to your vehicle.
MAKING A CALL FROM THE PHONEBOOK
1. Press the button on the steering wheel.
2. After waiting for the tone, say “Phone”.
3. After waiting for the tone, say “Call”.
4.After the next tone, speak the name of a phonebook entry. For example, “Michael Smith”.
In some cases, names stored using all UPPERCASE letters may not be recognized by the
Voice Recognition system.
MAKING A CALL BY PHONE NUMBER
1.Press the button on the steering wheel. A tone will sound.
2. After waiting for the tone, say “Phone”.
3.After waiting for the tone, say “Dial”.
4.Say the number you wish to call, starting with the
area code in single digit format.
5.When you have finished speaking the phone
number, the system repeats it back and announces
the available commands.
6. Say “Dial”. The system acknowledges the command
and makes the call.
RECEIVING/ENDING A CALL
To accept the call, press the button on the
steering wheel or touch the Answer key.
To reject the call, touch the Decline key.
To hang-up, press the button or touch the
Hang Up key.
For more information, refer to the “Hands-Free Phone (section 5)” and the
“Voice recognition (section 10) of your InTouch Owner’s Manual or please
visit www.InfinitiUSA.com/bluetooth.
24
Navigation System (if so equipped)
I NFINITI CONTROLLER - Turn to highlight
an item and press ENTER to select the
highlighted item on the upper display menu
screen. On the map screen, turn to adjust
the map scale. To scroll the map, push the
controller in the direction you want to scroll.
1
3
1 Upper Display - Displays the map and can be
controlled by the INFINITI controller.
2 Lower Display - Displays navigation functions
2
and is not controlled by the INFINITI controller.
Press the MENU button below the lower
display to access the navigation functions.
4
5
6
7
3 Map Scale - Touch to display the scale bar.
Touch ZOOM IN or ZOOM OUT to adjust
the map scale.
4 Street Address - Touch to search for a
destination by entering an address.
5 Points of Interest - Touch to search for a destination from different categories of
businesses or locations.
6 Home - Touch to search for a route from the vehicle’s current location to the stored home location.
7 D
estination - Touch to view multiple ways to set a destination.
For more information, refer to the “Navigation (section 9)” of your InTouch Owner’s Manual. 6
25
syste m g ui d e
HomeLink® Universal Transceiver (if so equipped)
HOMELINK
T he HomeLink® Universal Transceiver can learn and consolidate the functions of up to
three different hand-held transmitters, operating items such as garage doors, property
gates, outdoor and indoor lights or alarm systems.
To program the HomeLink® Universal Transceiver:
• P
osition the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the HomeLink indicator light in view.
• P
ress and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.
T o verify the programing is complete, press and hold the HomeLink button and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the HomeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds indicates
additional steps are required to complete the programing.
A
n additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink button, press and
release the learn or smart button (the name may vary by manufacturer, but it is usually
located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.
Y
ou may have to repeat the previous two steps up to 3 times to complete the programing
process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
26
me mo
memo
me mo
Helpful Resources
Below is a list of helpful resources that can be used to learn
more about the vehicle’s systems and feature operations.
Printing: September 2014 (02) / QR15EA HV37U0 / Printed in USA
• Vehicle Owner’s Manual
•Navigation Owner’s Manual (if so equipped)
•Printed Quick Reference Guide (this document)
•www.NissanUSA.com/bluetooth
•www.NissanUSA.com/connect
•www.youtube.com/user/NissanUSA
• Nissan Consumer Affairs 1-800-647-7261
•Electronic Quick Reference Guide
(use Quick Response (QR) code or URL below)
To view detailed instructional videos,
go to www.infinitiownersinfo.mobi/2015/q50
or snap this barcode with an appropriate
barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features of
your new vehicle. Please see your Owner’s Manual for important safety information and system
operation limitations. Features and equipment in your vehicle may vary depending on model,
trim level, options selected, order, date of production, region or availability. Therefore, you may
find information about features or equipment that are not included or installed on your vehicle.
All information, specifications and illustrations in this Quick Reference Guide are those in effect
at the time of printing. NISSAN reserves the right to change specifications, performance, design
or component suppliers without notice and without obligation. From time to time, NISSAN
may update or revise this Quick Reference Guide to provide owners with the most accurate
information currently available. Please carefully read and retain, with this Quick Reference Guide,
all revision updates sent to you by NISSAN to ensure you have access to accurate and up-to-date
information regarding your vehicle. Current versions of vehicle Quick Reference Guides, Owner’s
Manuals and any updates can also be found in the Owner section of the INFINITI website at
https://owners.infinitiusa.com/iowners/navigation/manualsAndGuides. If you have questions
concerning any information in your Owner’s Manual, contact INFINITI Consumer Affairs. See the
INFINITI CUSTOMER CARE PROGRAM page in the Owner’s Manual for contact information.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement