Amigo Fiesta 1 Owner's Manual

Amigo Fiesta 1 Owner's Manual
Fiesta One
OWNER’S MANUAL
1
TABLE OF CONTENT
1.
PREFACE…………………………………………………………….. 3
2.
SAFETY NOTICE…………………………………………………… 4
2.1 Before Driving
2.2 While Driving
3
EMI …………………………………………………………………… 7
4.
ASSEMBLY AND DISASSEMBLY………………………………… 9
5.
PARTS INTRODUCTION…………………………………………... 10
Parts Description
6.
OPERATION………………………………………………………… 11
6.1 Operation Panel
6.2 How to Operate Your Vehicle
6.3 How to Set to Freewheel Mode
7.
CHARGING AND BATTERY………………………………………. 16
7.1 Charging the Battery
7.2 Charger
7.3 Battery
8.
INSPECTION AND MAINTENANCE…………………………….. 19
8.1 Daily Checking
8.2 Regular Checking Record
8.3 Battery, Circuit Breaker and Tire
8.4 Maintenance
8.5 Storage
9.
TROUBLE SHOOTING…………………………………………….. 23
10.
SPECIFICATIONS………………………………………………….. 24
11.
WARRANTY…………………………………………………………. 25
11.1 Vehicle Serial Number
11.2 Warranty Policy
2
1 . P R E FAC E
Please carefully read this owner’s manual before using the vehicle. Improper use of the
vehicle could result in harm, injury or accidents.
♦ This owner’s manual includes operation instructions for all aspects of the vehicle,
assembly, and how to deal with possible accidents.
♦ This owner’s manual is written solely for the Fiesta™ One.
♦ The symbols used in this manual are explained below.
[
Warning
V
Attention
L
Improper use of this vehicle could lead to serious injury
Improper use of this vehicle could lead to personal injury and/or
property damage.
Suggestion Follow these instructions to maintain safe and efficient operations
and functions of this vehicle.
♦ This manual includes a repair and maintenance record chart and the Warranty. Please
keep it in safe place or in the vehicle.
♦ If someone else uses the vehicle, make sure that you give them the instruction
manual for his or her reference.
♦ We reserve the right to make design modification without notifying the buyer. It is
your responsibility to maintain an updated manual either by requesting it through
mail or visiting our website.
“Caution: Federal law restricts this device to sale by or on the order of a
practitioner licensed by the law of the State in which he/she practices.”
3
2.
SAFETY
N OT I C E
2.1 Before Driving
The user should get familiar with all functions and features to operate this vehicle before
driving. Please always keep safety in mind. There may be situations where the user
should have a trained assistant present so the user can become familiar with the
operations and functions of the vehicle. An assistant can be a family member or a care
professional. To minimize any personal injury please read all of the following safety
precautions prior to driving.
¾ The same traffic rules that apply to pedestrians apply to the use of this vehicle
For your safety, please follow the rules that apply to pedestrians.
♦ Ride on the sidewalk, parkway or pedestrian areas only. Never ride on freeways or
roads. It may be difficult for traffic to see you when driving your vehicle.
♦ Always be aware of all obstacles around you. (Cars, people, terrain, and weather).
♦ Be extremely cautious when driving your vehicle in busy areas, shopping malls,
business centers, etc.
♦ If you take prescription drugs please consult your physician before operating your
vehicle. Some medications may impair your ability to maintain safe operations of
your vehicle.
♦ Please do not operate your vehicle when you are under the influence of alcohol, this
may impair your ability to operate your vehicle in a safe manner.
♦ Please do not drive your vehicle at night.
♦ Please follow pedestrian traffic lights.
¾ Practice operating your vehicle
Use care and common sense when driving your vehicle. While becoming familiar
with the operations of your vehicle, please practice in a wide open area, like a park.
In order not to fall out of your vehicle while driving, keep in mind the status of the
driving motion, such as accelerating, stopping, turning, reversing and up-and-down
ramps.
♦ Please set the speed dial to the low setting during your initial practice.
♦ Be sure to have someone accompany you and watch out for your safety when
driving for the first time.
♦ Be sure you are able to control and operate your vehicle easily and confidently. Then
you can adjust your vehicle to a higher speed.
¾
The Fiesta One vehicle is limited to one passenger
Do not carry passengers on your vehicle. (Including children)
4
2.
SAFETY
N OT I C E
¾ Do not use this vehicle to carry or haul goods
♦ The maximum weight that can be carried is 220 lbs (100 kg) (includes goods). Refer
to section “9-SPECIFICATIONS” on page 24 “WEIGHT CAPACITY”
♦ Maximum loading weight for the basket is 8.8 lbs.
2.2 While Driving
¾ Please carry out daily inspections. It is important to complete your daily checklist
before each use to insure your vehicle will operate smoothly and safely.
Refer to section 7.1 “DAILY CHECKING” on page 19.
¾ Do not stretch your body out of the vehicle while driving
♦ Such action may cause you to lose your balance or to be injured due to falling.
♦ Pay attention to avoid your clothes being tangled in the wheels.
¾ When crossing train tracks.
♦ Before entering the crossing please stop completely. When crossing make sure that
the vehicles wheels do not get stuck in track.
¾ Do not use your vehicle under circumstances below.
♦ Roads with heavy traffic, mud, gravel, bumps, snow or ice. Use caution on roads
that have a canal or waterway without any fences or hedges or that are too narrow.
These conditions can affect the performance of your vehicle and could lead to an
accident or injury.
Keep away from places where your wheels may get stuck.
♦ Do not drive at night or in raining, snowing, misting or gale weather. Driving in
these conditions may affect your ability to drive in a safe manner and could lead to
an accident or injury.
♦ Do not drive your vehicle in “S” curves or make sudden turns. Sudden turns or
driving in a zig-zag motion can result in the tipping of your vehicle and could lead to
possible injury or damage to your vehicle. To avoid accidents, it is a good idea to
practice making turns to become familiar with how your vehicle maneuvers.
♦ Your vehicle is not designed to travel up or down stairs or escalators, always use an
elevator.
¾ About mobile phone and other electric equipment.
♦ Do not use a mobile phone or other wireless communication devices while driving.
♦ Do not charge your mobile phone or other electric device from your vehicle’s
battery.
¾ Ramps, inclines and declines
♦ Do not drive onto steep ramps. Refer to section “9-SPECIFICATIONS” on page 24
“SLOPE GRADE ABILITY.”
5
2.
SAFETY
N OT I C E
♦ When coming to an inclined road, please drive slowly. You should adjust the speed
dial to a middle setting. It is a good idea to maintain a safe speed and avoid any
sudden stops or starts. When going down a decline it is a good idea to set the speed
dial to a low setting to insure a safe and controlled descent. Never put the vehicle in
reverse when driving down a decline.
♦ Do not drive over large drop offs. Refer to section “9-SPECIFICATIONS” on page
24 “MAX. GROUND CLEARANCE”
♦ Do not cross wide gutters, it may cause your wheels to get stuck.
♦ Please slow down when driving on roads with drop offs.
♦ Do not make sudden turns when driving on gravel roads or ramps.
♦ Avoid any terrain or obstacle that makes you feel uncomfortable or if you have any
doubt that your vehicle will not perform in a safe manner.
♦ Many buildings now have ramps with 180 degree turns, so it is a good idea to
practice your turning skills so you do not get stuck on railings or get caught on any
obstacles which could lead to injury.
[ WARNING
♦ Do not set the vehicle in freewheel mode when driving on an incline or decline.
♦ To protect yourself, while you are driving down a steep decline (over 13 degrees),
the vehicle will not be driven automatically and an electromagnetic brake will
activate, turn the power on again to restart your vehicle.
¾ Maximum User Weight Limit
Refer to section “9-SPECIFICATIONS” on page 24 “WEIGHT CAPACITY.”
Loading over the limitation will lead to the damage of your vehicle or malfunction
and hence your safety. The warranty does not cover this type of over-loading
damage.
6
3.
EMI
This portion of the owner’s manual will provide the user with basic information about
the problems with EMI, known sources of EMI, protective measures either to lessen the
possibility of exposure or to minimize the degree of exposure; and this section also
shows some conditions that unexpected or erratic movements may occur.
Caution: It is very important that you read this information regarding the possible
effects of electromagnetic interference on your electric vehicle.
¾ ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE
SOURCES
Powered vehicles may be susceptible to electromagnetic interference (EMI), which is
interfering electromagnetic energy (EM) emitted from sources such as radio stations,
TV stations, amateur radio (HAM) transmitters, two-way radios, and cellular phones.
The interference from radio wave sources can cause an electric powered vehicle to
release its brakes, move by itself, or move in unintended directions. It can also
permanently damage the electric powered vehicle’s control system. The intensity of
the interfering EM energy can be measured in volts per meter (V/m). Each electric
powered vehicle can resist EMI up to certain intensity. This is called its “immunity
level”. The higher the immunity level is, the greater the protection is. At this time,
current technology is capable of achieving at least a 20 V/m immunity level, which
would provide useful protection from the more common sources of radiated EMI.
This electric powered vehicle model as shipped, with no further modification, has an
immunity level of 20 V/m without any accessories.
There are a number of sources of relatively intense electromagnetic fields in the
everyday environment. Some of these sources are obvious and easy to avoid. Others
are not apparent and exposure is unavoidable. However, we believe that by following
the warning listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held portable transceivers (transmitter-receivers) with the antenna mounted
directly on the transmitting unit. Examples include: citizens band (CB) radios,
walkie talkies, cellular telephones and other personal communication devices.
NOTE: Some cellular telephones and similar devices transmit signals while they are
ON, even when not being used.
2. Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances and taxis. These usually have the antenna mounted on the outside of
the vehicle.
7
3.
EMI
3. Long-range transmitters and transceivers, such as commercial broadcast transmitter
(radio and TV broadcast antenna towers) and amateur (HAM) radios.
Note: Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD players, and cassette players and small appliances, such
as electric shavers and hair dryers, are not likely to cause EMI problems to your
powered vehicle.
¾ ELECTRIC POWERED VEHICLE ELECTROMAGNETIC INTERFERENCE
(EMI)
Because EM energy rapidly becomes more intense as you move closer to the
transmitting antenna (source), the EM fields from hand-held radio wave sources
(transceivers) are of special concern. It is possible to unintentionally bring high
levels of EM energy very closer to the powered vehicle’s control system while using
these devices. This can affect powered vehicle movement and braking. The
warnings listed below are recommended to prevent possible interference with the
control system of the powered vehicle.
¾ WARNINGS
Electromagnetic interference (EMI) from sources such as radio and TV stations,
amateur radio (HAM) transmitters, two-way radios, and cellular phones can affect
electric powered vehicles and motorized scooters. Following the warnings listed
below should reduce the chance of unintended brake release or electric powered
vehicle movement that could lead to serious injuries.
1. Do not operate hand-held transceivers-receivers, such as citizens band (CB) radios,
or turn ON personal communication devices, such as cellular phones, while the
powered vehicle is turned ON.
2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
coming close to them.
3. If unintended movement or brake release occurs, turn the electric powered vehicle
OFF as soon as it is safe.
4. Be aware that adding accessories or components, or modifying the electric powered
vehicle, may make it more susceptible to EMI (Note: There is no easy way to
evaluate their effect on the overall immunity of the powered vehicle).
5. Report all incidents of unintended movement or brake release to the electric
powered vehicle to the manufacturer, and note whether there is a source of EMI
nearby.
¾ IMPORTANT INFORMATION
1. 20 Volts per meter (V/m) is generally an acceptable immunity level against EMI
(The higher the level, the greater the protection). This product has an immunity level
of 20 V/m without any accessories connected to it.
8
4 . A S S E M B LY A N D D I S A S S E M B L E Y
¾ Removing the Seat and Folding the Handle
1.Remove the seat height adjuster pin and
loosen the seat height adjustment bolt.
2.Once you have removed the pin and loosened
the bolt (As shown by arrows)
3.Remove the seat by pulling it up
from the base of the vehicle.
4. Loosen the tiller and fold the handle bars down.
¾ Removing the Battery Pack
¾ Removing the Rear Wheels and Motor
¾ Note
9
5.
¾
PA R T S I N T RO D U C T I O N
PARTS DESCRIPTION, FIESTA ONE
1.Speed Dial
2.Speed Control Lever
3.Rubber Handlebar
4. Tiller
5. Tiller Angle Adjustment
6. Head Tube
7. Fork
8. Front Wheel
9. Foldable Seat
10. Seat Turning Lever
11. Seat Height-Adjusting Pin
12. Battery Carrying Lever
13. Rear Wheel
14.Motor/Rear Wheel Carrying Lever 15.Off-BoardChargerSocket
16.Freewheel Mode Lever 17. Anti-Tip Wheels
18.Reset
1.
2.
9.
3.
4.
10.
5.
11.
12.
6.
7.
8.
13.
14.
15.
16.
17.
18.
10
6.
O P E R AT I O N
6.1 OPERATION PANEL
1.
2.
3.
4.
5.
6.
Speed Dial
Horn Button
Handle Bar
Key Hole
Speed Control Lever
Battery Condition Meter
6.2 HOW TO OPERATE YOUR VEHICLE
¾ Power switch
Turn the key to power ON or OFF
ON: Power is turned on when key is in the
Horizontal position
OFF: Power is turned off when key is in the
Vertical position
¾ Speed Dial
Allows the user to adjust the forward and
reverse speed.
¾ Forward, Reverse and Braking
♦ Pull the speed control lever down with your right hand and the vehicle will move
forward.
♦ Pull the speed control lever down with your left hand and the vehicle will move
backward.
♦ The horn will beep when the vehicle is in reverse.
♦ Release the speed control lever while in either forward or reverse direction, the
electromagnetic brake in the motor will be activated and the vehicle will stop.
11
6 . O P E R AT I O N
¾ Horn Button
The warning horn will be activated when you push the button. Push the button again,
and the horn will be cancelled.
¾ Key Hole/ Power Switch
Turning the key to “ON” will turn on the vehicle.
¾ Braking
♦ Electromagnetic brake: Release the speed control lever completely and the
electromagnetic brake will be activated.
[ WARNING
When going down an incline, NEVER set to free-wheel mode. In such cases, the
electromagnetic brake will not activate.
¾ Seat
♦ The seat can be turned to 90 degree increments.
♦ Push the seat adjustable bar forward to change angle
♦ Seat height can be adjusted by loosening the seat
height adjustment bolt and removing the seat height
adjustment pin, adjusting the seat to the desired
height and then re-tightening the bolt and inserting
the seat height adjustment pin.
¾ Armrest Adjustment
♦ The armrest width can be adjusted using a 5mm Allen
wrench.
VATTENTION
Be sure to return the seat to the forward position before driving.
12
6 . O P E R AT I O N
¾ Battery Condition Meter
♦ The needle points out the remaining power. Right
side in green range: full power. Left-side in red
range: not enough power.
♦ The remaining power indicated by battery meter
will vary by the driving time and the way the
vehicle is driven. The repeated starting, stopping,
climbing will consume the power more quickly.
L SUGGESTION
1. You are recommended to charge the batteries immediately when the needle points to
the yellow or red area.
2. After charging or replacing the batteries, drive the vehicle for 2-3 minutes to make
sure the battery holds a charge.
3. In wintertime, the batteries may respond slower and the traveling distance may be less
than in the summertime.
4. When driving on an incline, the needle may suddenly move to red and yellow area,
and move back to the green area when the vehicle is on level ground. This is normal.
5. Under normal circumstances, it is natural for the capacity of the batteries to decay as
time passes which will result in short travel distance compared to brand new batteries.
When you find the travel distance is about 50% of brand new batteries traveling
distance, it is time for replacement batteries. If you continue to use the old batteries
less travel distance will be expected.
6. Travel distances will be shortened when driving frequently on a slope or ground with
big dips, due to more power consumption.
¾ Tiller Adjustment
The Tiller can be adjusted between 00 ~800 by following these steps.
1. Loosen the adjusting lever on the tiller.
2. Adjust the tiller to the desired angle.
3. Tighten the lever, and the tiller will be fixed in the desired angle.
13
6 . O P E R AT I O N
¾ Starting and Driving
1.
2.
3.
4.
5.
Make sure the seat is properly installed.
Make sure the tiller has been properly secured.
Make sure the armrest has been returned to the lowest position.
Turn the power switch to “ON”. .
Check battery meter to ensure there is enough power for your trips. If you have the
doubt about the remaining power, please charge the battery before leaving.
6. Set to the proper speed by the speed dial.
7. Be sure the forward / reverse speed lever is in working condition.
8. Make sure the electromagnetic brake is in working condition.
V ATTENTION
1. Do not push both Right Hand & Left Hand side speed levers simultaneously. This
might lead you to be unable to control your vehicle.
2. Do not turn the power switch to OFF while driving. This will lead to an emergency
stop and possible danger.
3. Do not set to highest speed when driving indoors.
4. Do not adjust speed dial while driving, the sudden change of the highest speed may
endanger you and cause the failure of your vehicle.
5. Do not place magnetic devices near the area of the control panel. This could affect the
safe operation of your vehicle.
6. Be careful while driving in heavy traffic or crowded areas.
7. While reversing the vehicle, be aware of people or objects around you.
¾ About Driving speed
The speed scale is printed on speed dial label, ranging from left (Lowest speed) to right
(Highest speed.) The end of right side is the maximum speed.
Speed Scale
Left side
Middle
Right side
Circumstances of Recommend speed
♦ Speed equivalent to walking slowly
♦ On an incline or decline
♦ Driving indoors or in a narrow space
♦ Speed equivalent to walking normally
♦ Driving outdoors on flat ground
♦ Speed equivalent to walking quickly
♦ Driving in an open space.
14
6 . O P E R AT I O N
¾ Stopping
1. Release the speed control lever completely. The vehicle will naturally brake and stop.
2. Turn the power switch to “OFF”. Then pull out the key.
VATTENTION
♦ The stopping distance will vary with your forward / reverse speed. Begin braking as
early as you can.
♦ While parking your vehicle, be sure to park on flat ground and then turn the power
to “OFF” before you get off.
6.3 HOW TO SET TO FREE-WHEEL MODE
♦ Driving mode: Push the lever down completely, the vehicle can be driven by motor
power.
♦ Free-wheel Mode: Lift the lever up completely, the vehicle can be moved manually.
Freewheel Mode
Drive–on Mode
15
7 . C H A RG I N G A N D BAT T E RY
7.1 CHARGING BATTERY
Be sure to follow all procedures below.
1. Turn the power switch to “OFF.”
2. Open the charging socket cap and insert charger.
3. Do not stop the charge until the battery is
completely charged.
4. The charging duration is 8 hours, but it will vary up to 10
hours, based on the status of battery and ambient
temperature.
5. The battery package can be removed from vehicle and
separately charged.
6. Disconnect the cord when charging is complete.
L SUGGESTION
1. Do not disconnect the charger cord if the charging is not completed. The battery life
will be seriously shortened or decayed if the batteries are repeatedly used without
being fully charged. Be sure to fully charge the batteries every time.
2. Always continue the charge until the needle stops in green area. NEVER stop
charging before it is completed.
3. When finished charging, the electric power will slowly discharge if the cord is
disconnected.
4. If you do not use your vehicle for long periods of time, it should be charged at least
every three months to keep the batteries in good condition.
5. Charging time will be affected by the ambient temperature, and it will be longer in
the wintertime.
VATTENTION: Please follow the rules below to avoid accidents while charging.
1. Please charge the batteries completely with every use and make sure voltage is correct.
2. Never disassemble or modify the plug.
3. Please charge in a well ventilated space that is not directly exposed to sunlight. Do not
charge in a space which is humid, or under rainfall and morning dews.
4. Do not cover the vehicle with any waterproof cloth or other objects while charging.
5. Do not charge in temperatures less than 14 degrees F or higher than 122 degrees F, as
the charger may not work and the battery may be damaged.
16
7 . C H A RG I N G A N D BAT T E RY
[ WARNING
1. Keep away from flammable objects while charging. This may lead to fire or
explosion of the batteries.
2. As the batteries may produce hydrogen, do not smoke while charging. Always
charge your batteries in a well-ventilated space.
3. Never connect or disconnect the charger cord with wet hands. Do not connect or
disconnect the charger cord if it is wet. This may lead to an electric shock.
7.2 CHARGER
♦ Never pull out the charging cord before the battery
is fully charged. The charging cord should be away
from heat and water. When charging, the cord needs
to be tightly inserted in the sockets.
[WARNING
Please park the vehicle near the electric outlet and slowly pull out the charging cord.
If the charging cord is broken, DO NOT charge the vehicle until a new charger cord
is obtained.
7.3
BATTERY
♦ Do not expose the battery to temperatures below 14 degrees F or above 122 degrees F
when charging or storing the vehicle. Exceeding the specified temperature ranges can
lead to freezing or over heating of the batteries. Such case will damage the batteries
and shorten their lifetime.
♦ The batteries used on your vehicle are sealed lead acid batteries, maintenance-free, so
it is not necessary to change the batteries’ liquid or refill the liquid.
[WARNING
Do not open the battery seal cap at any time.
17
7 . C H A RG I N G A N D BAT T E RY
¾ Cleaning the battery
If the battery is contaminated by dirty water, battery acid, dust or other garbage, the
battery will discharge quickly. Follow these steps to clean the battery.
1.
2.
3.
4.
5.
6.
Turn the vehicle power switch to OFF.
Remove the seat and battery pack.
Remove the battery case cover by removing fasteners.
Use a clean cloth to wipe off the soiled area.
Take out the battery.
Clean the battery with a clean cloth. If the terminal is covered by white powder, please
clean it by using warm water.
7. Reassemble battery pack.
L SUGGESTION
If necessary, ask for help from your local Dealer for cleansing and replacing of the
battery.
L SUGGESTION
1. Make sure the terminal is installed properly and replace the cover.
2. Do not use the batteries to charge telecom equipment or other items.
3. Battery capability will vary with outside conditions. The driving distances will
be shorter in the winter. If the vehicle is not to be used for a long time, please
charge the batteries at least every three months.
4. Always replace both batteries simultaneously.
18
8. INSPECTION AND MAINTENANCE
8.1 DAILY CHECKING
Check following items before driving. If you find any thing abnormal, go to your
local Dealer for further instructions before using it.
Item
♦
♦
Speed Control Dial
♦
♦
Speed Control Lever
♦
♦
Motor
♦
Freewheel Mode
♦
♦
Battery Condition meter
♦
Horn
♦
Seat
♦
♦
Tires
♦
♦
♦
Other
♦
Handle bar
Inspection Content
Are they loose?
Can they be turned left and right smoothly?
Can it be adjusted freely and function properly?
Does the vehicle move when the lever is pressed down?
Does the vehicle stop if the lever is released?
Are there any abnormal noises from the motor?
Does the electromagnetic brake work properly?
Does free-wheel mode lever work properly?
Does the needle move when power is switched on?
Is the remaining power enough for your trip?
Does the horn work properly?
Can the seat be turned and adjusted properly?
Are there any cracks or other damage to the tires?
Do they have proper air pressure?
Check the tires tread depth.
Are there any abnormal noises?
Is there oil leakage from transmission box?
VATTENTION
Go to your local Dealer for inspection and maintenance if you find anything wrong.
19
8. INSPECTION AND MAINTENANCE
8.2 REGULAR CHECKING RECORD
To make sure your vehicle remains in good condition, go to your local Dealer regularly
for maintenance and record it every six months after purchasing. (Fee Required)
L SUGGESTION
Even if you don’t use your vehicle for a long time, the vehicle should be maintained
regularly.
I – Inspection
C - Clean
Item \ Period
A-Adjustment
L - Add Oil
R-Repair
RP- Replacement
1
mth
Forward/Reverse speed lever
Operate
The function of switches
Panel
Connection of Socket / Plug is good?
Operation and Noise
Motor Function of Electromagnetic Brakes
Connection of Socket / Plug is good?
Trans- Freewheel mode lever
mission Any oil leakage from transmission box
Looseness or corrosion of terminals
Battery Connection of Socket / Plug is good
Any broken electrical cords
Charging function and LED light
Charger
Any broken Sockets / Plugs / Cords
Angle adjustment bar
Seat
Seat post looseness
Right /Left Turn of tiller
Tiller
Adjustment of Tiller angle
Crack or damage of tire surface
Tire
Tread depth
Abnormal wearing
20
6
mth
12
mth
T - Tightening
18
mth
24
mth
30
mth
8. INSPECTION AND MAINTENANCE
Item \ Period
Wheel
Rim
1
mth
6
mth
12
mth
18
mth
24
mth
30
mth
Tightness of bolts and nuts
Wear or deformation around tires
Checked by
Inspector
Date Checked
8.3 BATTERY, CIRCUIT BREAKER AND TIRE
¾ Battery
Refer to section “7-CHARGING AND BATTERY” on page 17 “7.3 BATTERY”
¾ Circuit Breaker
There is one circuit breaker on the vehicle. It is located near the rear of the vehicle. If
the power switch is ON, and needle of the battery condition meter doesn’t move, check
the circuit breaker.
L SUGGESTION
Ask for help from your local Dealer for inspecting or replacing the fuse, since the
tiller shroud has to be removed first for replacement of fuse.
¾ Tire
The condition of the tires depends on how you drive and use your vehicle.
♦ Inspecting Tire Tread
♦ Please check the tread depth regularly. Replace the tires when the tread depth is less
than 0.5 mm.
VATTENTION
When tread depth is below 0.5mm, it can easily lead to vehicle slippage, making
braking distances longer. Replace the tires as soon as possible.
21
8. INSPECTION AND MAINTENANCE
8.4 MAINTENANCE
♦ You must maintain the vehicle frequently if you constantly drive on grass, sand, or
gravel road.
♦ Do not use water, oil or other chemical solution to clean your vehicle. To prevent
damaging the electronic components and PC board, do not spray the vehicle with water.
Please clean the vehicle by wiping it with either dry or moist cloth.
♦ Please take the vehicle to your local Dealer for repairs and adjustments. Improper
adjustments could lead to accidents or vehicle malfunction.
♦ Please use soft and dry clothes to keep your vehicle tidy. Please use moderate or mild
detergents to clean the vehicle.
VATTENTION
When conducting the maintenance of your vehicle, please turn the power switch OFF
and remove the charger cords.
LSUGGESTION
♦ Do not splash water directly on your vehicle. This could lead to the malfunction of
the electric system.
♦ Do not use gasoline, solvents or vaporizing solution, the shroud may be deformed or
damaged.
♦ Do not use wax.
8.5
STORAGE
Make sure the vehicle is stored under the following circumstances:
♦ Make sure the Power switch is turned to “OFF”.
L SUGGESTION
Please store the vehicle in a location where it is out of direct sunlight, rain, or dew.
When stored for a long time, please charge the battery to the full power and then
disconnect the battery terminal. For any details, inquire at your local Dealer.
22
9 . T RO U B L E S H O OT I N G
¾ When you have trouble with your vehicle
♦ You can inspect the following before taking your vehicle to your local Dealer.
Problem
Checking points and corrective action
Does not start ♦ Is the power switch set OFF?
↓
Turn the power switch to ON.
♦ Does the battery still have power?
♦ Is the battery indicator working?
↓
Charge the battery.
♦ Is the charger plugged into the vehicle?
↓
Unplug the charger and put away the cord.
Does not go
♦ Check to be sure the free wheel lever is engaged
¾ If you cannot solve the problem by yourself, contact your local Dealer for help.
23
1 0 . S P E C I F I C AT I O N S
Fiesta One
Model name
Overall Height (without seat)
34.6”
Overall Length
39.5”
Overall Width
19.7”
Motor Output
DC 24V 270W
12V×12AH×2PCs
HP 24V 3AMP (Automatic Type)
off-board
Battery
Charger
Front Wheel
2”x8” foam filled tire × 1 PCs
(50mmx200mm)
Rear Wheel
2”x8” foam filled tire × 2 PCs
(50mmx200mm)
Break System
Intelligent regenerative electromagnetic brake
102 lbs (including seat and battery)
Net Weight
220 lbs (100 kg)
Weight Capacity
13 degrees
Slope Grade Ability
8-10 miles (12-16 km)
Continuous Traveling Distance
Forward: 4.4 mph (7.1km/h)
Maximum Speed
Turning Radius
36.5" (927.1mm)
Maximum Ground Clearance
1.88” (47.8mm)
Seat Overall Height
13.4" (340mm)
Seat Overall Width
15.7" (400mm)
Seat Overall Depth
15.4" (390mm)
Seat Overall Weight
23 lbs (10.4 kg)
Remark -- The manufacturer reserves the right to modify the specifications if needed. The
final specifications are subject to any change when you purchase the vehicle at the shop.
Traveling distance range is based on a 180 pound (81kg) driver on a flat surface. Range
depends on battery type, driver weight, terrain traveled, ambient temperature, and user’s
charging routine.
24
11. WARRANTY
11.1 VSN (VEHICLE SERIAL NUMBER)
To ensure after-sale service and warranty service, please fill in the vehicle serial number
that is located on the back right hand side of the frame.
Model
Serial #
Fiesta One
11.2 WARRANTY POLICY
Amigo Mobility International, Inc. (AMI) warranties the original completed unit it
distributes to the original purchaser.
1. Structural components including platform, seat post, transaxle, motor, controller,
battery charger and seat, are warranted against defects in materials and workmanship
for one (1) year. Cuts and tears in seats are not covered by warranty.
2. AMI warranties batteries supplied from its factory. AMI factory-supplied batteries
carry Amigo brand labels. A six-month battery warranty from the date of purchase
applies against the battery manufacturer’s defects in workmanship or materials.
Damage caused by battery moisture, spillage, or leakage is exclusive of warranty.
When removing a battery, always set on cardboard or newspapers to avoid damage.
3. Weight Restrictions: PLATFORM: Use of this product by persons exceeding
220lbs. is not recommended and limits warranty to six (6) months.
4. Items replaced under warranty, are covered by the original warranty. (Warranty
replacement does not extend the warranty period.)
5. AMI is obligated to repair or replace products or parts returned by the purchaser, and
found to be defective under warranty at its headquarters in Bridgeport, Michigan.
6. For unit and parts, this warranty does not cover accidental damage, misuse, normal
wear and tear, such as LED lights, electrical and mechanical switches, wires, belts,
chains and resistors, or use of products for other than personal purposes. Damage
during shipment is not covered by the warranty.
7. If inspection determines that a returned part or unit is fully functional, it will be
returned at the expense of the owner. Opening sealed components will void the
warranty.
8. Accessories and parts that are not a part of the original completed unit, or rebuilt units,
will have a one (1) year warranty against defects in materials and workmanship.
25
11. WARRANTY
This warranty begins when the unit is sold to the original owner. If warranty
information, such as owner’s name, serial number or date of purchase is not available,
then AMI will use the production date of the unit as the effective warranty date.
This warranty supersedes and is in lieu of all other warranties, expressed or implied, and
no person, agent or dealer is authorized to give any warranties on behalf of AMI, nor to
assume for AMI any other liability concerning any of its products unless made in writing
and signed by an official of AMI. Any unauthorized repair or modification will void
this warranty and release AMI from any liability.
This warranty gives you specific rights, with the possibility of other rights, which vary
depending upon your locality.
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement