Aten VS0201 2-Port VGA Switch User Manual
ATEN VS0401 is a high-performance KVM switch that allows users to control up to four computers using a single keyboard, mouse, and monitor. It features advanced capabilities such as front panel pushbuttons for easy port selection, remote control for switching from anywhere in the room, and RS-232 serial commands for integration with home automation systems or other control devices.
Advertisement
Advertisement
2/4-Port VGA Switch with Audio
VS0201 / VS0401
User Manual
www.aten.com
ii
VS0201 / VS0401 User Manual
FCC Information
Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that relates to China.
VS0201 / VS0401 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International http://support.aten.com
Telephone Support
For telephone support, call this number:
International
China
Japan
Korea
North America
United Kingdom
886-2-8692-6959
86-10-5255-0110
81-3-5615-5811
82-2-467-6789
1-888-999-ATEN ext 4988
44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iii
VS0201 / VS0401 User Manual
Package Contents
The VS0201 / VS0401 package consists of:
1 VS0201 / VS0401 2/4-Port VGA Switch with Audio
1 Power Adapter
1 User Instructions*
Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit, and/or any of the devices connected to it.
* Features may have been added to the VS0201 / VS0401 since this manual was published. Please visit our website to download the most up-to-date version.
© Copyright 2015 ATEN® International Co., Ltd.
Manual Date: 2015-07-24
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
iv
VS0201 / VS0401 User Manual
Contents
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
VS0201 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VS0401 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VS0201 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
VS0401 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the RS-232 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Manual Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pushbutton Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VS0201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VS0401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Configuring the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switch Port Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
v
VS0201 / VS0401 User Manual
Switch Mode Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Echo Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Standby Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Dynamic DDC Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Pushbutton Lock Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Read Firmware Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Baud Rate Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 23
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Appendix
vi
VS0201 / VS0401 User Manual
About this Manual
This User Manual is provided to help you get the most from your system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VS0201 / VS0401 system.
Its purpose, features and benefits are presented, and its front and back panel components are described.
Chapter 2, Hardware Setup, describes how to set up your VS0201 /
VS0401 installation.
Chapter 3, Operation, explains the fundamental concepts involved in
operating the VS0201 / VS0401.
Chapter 4, The Firmware Upgrade Utility, explains how to download the
firmware upgrade utility and install updates on the VS0201 / VS0401.
An Appendix, provides specifications and other technical information regarding the VS0201 / VS0401.
vii
VS0201 / VS0401 User Manual
Conventions
This manual uses the following conventions:
Monospaced
[ ]
1.
♦
→
Indicates text that you should key in.
Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them:
[Ctrl+Alt].
Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start
→
Run means to open the Start menu, and then select Run.
Indicates critical information.
Product Information
For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
International
North America http://www.aten.com
http://www.aten-usa.com
viii
Chapter 1
Introduction
Overview
The VS0201 / VS0401 2/4-Port VGA Switch with Audio allows you to connect two/four source computers to a single monitor or projector with full audio and quickly switch between the devices for use.
The convenient front panel pushbuttons and IR remote control allow you to easily toggle between VGA/Audio sources, while front panel LEDs indicate the connected source device at a glance. In addition, with support for up to 300
MHz bandwidth, the VS0201 / VS0401 allows for the transmission of large amounts of display information at very high speeds for a clear professional appearance.
Furthermore, for complete systems integration, serial control is standard through the VS0201 / VS0401’s built-in RS-232 ports, which allow the switch to be controlled through a high-end controller or PC.
The ability to use high-end serial control devices to initiate RS-232 commands allows the VS0201 / VS0401 to be controlled by a secondary system to utilize advanced switch functions such as port switching, auto switching, and front panel pushbutton lock.
The VS0201 / VS0401 is perfect for the meeting room, media centers, class rooms, or any presentation environment requiring multiple audio/video sources to be accessed on a single display.
1
VS0201 / VS0401 User Manual
Features
Displays the video output of two (VS0201) or four (VS0401) computers on a single monitor or projector
Quick and easy switching between VGA/Audio sources via front panel pushbuttons, RS-232, or IR remote control
Superior video quality – up to 1920 x 1440
Long-distance transmission – up to 65 m
Supports– VGA, SVGA, UXGA, WUXGA, and multisync monitors
Video DynaSync™ - Exclusive ATEN technology eliminates boot-up display problems and optimizes resolution when switching between ports
Built-in bi-directional RS-232 serial port for high-end system control, and advanced RS-232 functions*
RS-232 Functions:
Auto Switching – sets the priority for auto switching to a connected port
Pushbutton Lock – locks use of the front panel pushbuttons
Supports stereo audio
Dynamic DDC compatible
Supports up to 300 MHz bandwidth for optimal video quality
LED indication of power status and source device
All-metal casing provides durability and protection
Plug-and-play – no software installation required
Note: The VS0201 / VS0401 RS-232 AP and GUI instructions can be downloaded from the ATEN website: www.aten.com.
2
Chapter 1. Introduction
Requirements
Source Device
The following equipment must be installed on the source device or computer that acts as a source of VGA/Audio content:
VGA video card with HDB-15 connector
Audio source with stereo output
Display Device
A VGA, SVGA, UXGA, WUXGA or multisync monitor or multimedia projector with an HDB-15 connector
Stereo and/or balanced audio speakers
Cables
1 VGA/Audio cable for each source device you will be connecting
1 VGA/Audio cable for your display device
3
VS0201 / VS0401 User Manual
Components
VS0201 Front View
1
VS0401 Front View
1
2
3 4
4
3
4
2
No.
1
Component
Port Selection
Pushbuttons
2 Port LEDs
3
4
Power Pushbutton
Power LED
Function
Pressing a port selection pushbutton routes the
VGA/Audio source from the corresponding input port to the output port for display.
There is one port LED next to each port selection pushbutton. This lights green to indicate that the corresponding port has been selected.
The connected port LED will flash when the front panel pushbuttons are manually locked.
Push this button to turn on / off the switch.
The LED (green) lights up when the switch is powered on.
The LED (orange) lights up to indicate that the switch is in standby mode.
Chapter 1. Introduction
VS0201 Rear View
2
3
4
1
5
6
VS0401 Rear View
2
3
1
5
6
4
No.
1
2
3
4
5
6
Component
Grounding Terminal
Function
The grounding wire used to ground the unit attaches here.
RS-232 Serial Port This is the serial remote port for input source selection and high-end system control.
Connect the IR Receiver to this port.
External IR Receiver
Port
Video / Audio Input Each input section is comprised of a VGA connector and a mini stereo audio jack. The cables that connect to the video and audio output ports on the computers/source devices plug in here.
Power Jack The power adapter cable plugs in here.
Video / Audio Output The cables that connect to the video and audio ports for the video display and audio output plug in here.
5
VS0201 / VS0401 User Manual
This Page Intentionally Left Blank
6
Chapter 2
Hardware Setup
1. Important safety information regarding the placement of this
device is provided on page 29. Please review it before
proceeding.
2. Make sure that the power to all devices connected to the installation are turned off. You must unplug the power cords of any computers that have the Keyboard Power On function.
Installation
Installation of the VS0201 / VS0401 is simply a matter of plugging in the appropriate cables.
To install the switch, refer to the installation diagram on page 8 as you perform
the following steps:
1. Use a VGA/Audio cable to connect the VGA/Audio input of the video display and speaker devices to the VGA/Audio output ports on the rear of the VS0201 / VS0401.
2. Use VGA/Audio cables to connect the VGA/Audio output ports on the source device(s) to the VGA/Audio input ports on the VS0201 / VS0401.
Two/Four VGA/Audio input ports are located on the rear of the switch.
3. Use a grounding wire to ground the unit by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object.
4. Plug the provided power adapter into an appropriate AC power source; plug the power adapter cable into the power jack on the VS0201 / VS0401.
5. (Optional) To control the VS0201 / VS0401 system through the RS-232 port, connect the hardware/software controller here.
6. (Optional) Connect the IR Receiver into the External IR Receiver Input
Port.
The installation is complete, you may power on the display and source devices.
7
VS0201 / VS0401 User Manual
Installation Diagram
5
3
6
4
OR
1
2
Installing the RS-232 Controller
In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS0201 / VS0401, use a RS-232 serial cable. The end connecting to the VS0201 / VS0401 should have a 9-pin male connector. Refer to step 5 on the diagram above.
Note: To configure the RS-232 serial port see page 11.
8
Chapter 3
Operation
Overview
The VS0201 / VS0401 2/4-Port VGA Switch with Audio offers easy source device selection with either the front panel pushbuttons, IR remote control, or
RS-232 serial interface. This chapter describes Source Selection, Power on
Detection mode, Pushbutton Lock, Powering Off/Restarting, and the RS-232 serial port configuration and commands.
Note: Whenever the VS0201 / VS0401 is powered on, it automatically remembers the last connected port being used and connects to it.You may choose one of the methods outlined below to select a different port.
Manual Source Selection
To select the source device to view on your VGA display, press the front panel pushbutton that corresponds to the port it is connected to.
Note: The Port LED (green) light indicates which port is currently selected.
Remote Control Source Selection
First plug the External IR Receiver into the rear of the VS0201 / VS0401, place the receiver where the IR signal can be reached, and aim the remote at the
External IR receiver.
To select a source device with the remote control, press the number button that corresponds to the port it is connected to, or cycle through the source devices by pushing the Port Up and Port Down buttons on the remote control unit, as such:
Use the Port Up button to select the next port in ascending order (from left to right on the front view panel).
Use the Port Down button to select the previous port in descending order
(from right to left on the front view panel).
9
VS0201 / VS0401 User Manual
Pushbutton Lock
Pushbutton Lock allows you to secure your device by locking use of the front panel pushbuttons. To lock/unlock the front panel pushbuttons, do the following:
VS0201
Press and hold both 1 and 2 port selection pushbuttons for 5 seconds, then release.
VS0401
Press and hold both 1 and 4 port selection pushbuttons for 5 seconds, then release.
Note: 1. The front panel port LED will flash at one second intervals to indicate the pushbutton lock feature is enabled.
2. Repeat the steps above to unlock the front panel pushbuttons.
Powering Off and Restarting
If you power off the VS0201 / VS0401, follow these steps before powering it on again:
1. Power off the attached devices.
2. Unplug the power adapter cable from the VS0201 / VS0401.
3. Wait 10 seconds, and then plug the power adapter cable back in.
4. After the VS0201 / VS0401 is powered on, power on the attached devices.
10
Chapter 3. Operation
RS-232 Serial Interface
The VS0201 / VS0401’s built-in bi-directional RS-232 serial interface allows system control through a high-end controller, PC, and/or home automation / home theater software package.
Configuring the Serial Port
The controller’s serial port should be configured as follows:
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
19200
8
None
1
None
The RS-232 control commands for Switch Port, Auto Switch, Power on
Detection, Dynamic DDC, Pushbutton Lock, Read Firmware and Reset are found on the pages that follow.
Verification
In the steps below, after entering a command, a verification message appears at the end of the command line as follows:
Command OK - indicates that the command is correct and successfully performed by the switch
Command incorrect - indicates that the command has the wrong format and/or values.
11
VS0201 / VS0401 User Manual
Switch Port Command
The formulas for Switch Port commands are as follows:
1. Switch Command + Input Command + Port Number [Enter]
For example, to switch the input port to port 02, type the following:
sw i02 [Enter]
2. Switch Command + Control [Enter]
For example, to switch to the next port, type the following:
sw + [Enter]
The following tables show the possible values and formats for the Switch Port formulas:
Command
sw
Description
Switch command
Input Command
i
Description
Input command
Port number
xx
Control
+
-
Description
01-04 port (default is 01)
Description
Switch to next port
Switch to previous port
Note: 1. Each command string can be separated with a space.
2. If the Port Number string is skipped, the default value is used.
The following table shows the available list of commands:
Command
sw
Input
i
Port
xx
Control Enter Description
[Enter] Switch to input port xx
+
-
[Enter]
[Enter]
Switch to the next input
Switch to the previous input
12
Chapter 3. Operation
Switch Mode Command
You can choose how the VS0201 / VS0401 behaves when a new input source is connected. There are three Switch Modes:
Default- The switch behaves normally without the automatic switching operation.
Next- Switch priority is placed on the next port that has a new source device connected to it (default).
Auto- Places priority on a selected port so that when a source is connected to the said port, the VS0201 / VS0401 automatically switches to it, and the port can not be changed until the source is unplugged or auto switching is disabled.
In addition, the Go To function enables the VS0201 / VS0401 to switch to the next port with a powered on source device when the current input source device is powered off. The Go To function works independent of the modes listed above.
The formulas for Switch Mode commands are as follows:
1. Switch Mode Command + Input Command + Port Number + Control
[Enter]
For example, to enable Auto mode for port 02, type the following:
swmode i02 auto [Enter]
2. Switch Mode Command + Control [Enter]
For example, to enable Next mode, type the following:
swmode next [Enter]
3. Switch Mode Command + Control [Enter]
For example, to enable Default mode to disable Next/Auto mode, type the following:
swmode default [Enter]
4. Switch Mode Command + Control [Enter]
For example, to enable the Go To function, type the following:
swmode goto on [Enter]
13
VS0201 / VS0401 User Manual
The following tables show the possible values and formats for the Switch
Mode formulas:
Command
swmode
Description
Switch Mode command
Input Command
i
Description
Input command
Port number
xx
Control
default next auto
Control
goto on goto off
Description
01-04 port (default is 01)
Description
No automatic switching operation
Priority is placed on the next port that has a new source connected to it (default)
Priority is placed on a selected port
Description
Enable Go To function:
Switch to the next port with a powered on source device when the current input source is off
Disable Go To function (default)
The following table lists the available commands:
Command
swmode
Input
i
Port #
xx
Control
default next auto goto on goto off
Enter Description
[Enter] Use Default switch mode
[Enter] Use Next switch mode
[Enter] Use Auto switch mode for port #
[Enter] Go To function enabled
[Enter] Go To function disabled
14
Chapter 3. Operation
Echo Command
If the Echo feature is enabled, each action from the front panel pushbuttons or
IR remote control sends a corresponding acknowledgement message to the controller or management device connected to the RS-232 port.
The formula for the Echo command is as follows:
1. Echo Command + Control [Enter]
For example, to enable the Echo function, type the following:
echo on [enter]
The following tables show the possible values and formats for the Control formulas:
Command
echo
Description
Echo command
Control
on off
Description
Enable Echo function
Disable Echo function (default)
The following table lists the available commands:
Command
echo
Control
on off
Enter
[Enter]
[Enter]
Description
Echo function enabled
Echo function disabled
15
VS0201 / VS0401 User Manual
Standby Command
The Standby command puts the device in a power saving mode. The action is the same as using the front panel or IR remote power button. When standby mode is on or off either of the three methods (RS-232, front panel, or remote control) can bring the device into or out off standby mode.
The formula for the Standby command is as follows:
1. Standby Command + Control [Enter]
For example, to put the device in standby mode, type the following:
standby on [Enter]
The following tables show the possible values and formats for the Standby formulas:
Command Description
Control
on off
Description
Enable Standby mode
Disable Standby mode (default)
Note: Each command can be separated with a space.
The following table lists the available commands:
Command
standby
Control
on off
Enter
[Enter]
[Enter]
Description
Standby mode enabled
Standby mode disabled (default)
16
Chapter 3. Operation
Dynamic DDC Command
The Dynamic DDC feature is used to monitor the connected display and provide the correct updated EDID information to the source device so that the display is optimized. With Dynamic DDC off, source devices do not receive updated EDID data which can cause display issues. If there is a problem with your display quality, it is recommended that Dynamic DDC be turned off.
The formula for the Dynamic DDC command is as follows:
1. Dynamic DDC Command + Control [Enter]
For example, to turn on the Dynamic DDC feature, type the following:
ddc on [Enter]
The following tables show the possible values and formats for the Dynamic
DDC formulas:
Command
ddc
Description
Dynamic DDC command
Control
on off
Description
Enable Dynamic DDC
Disable Dynamic DDC (default)
Note: Each command can be separated with a space.
The following table lists the available commands:
Command
ddc
Control
on off
Enter
[Enter]
[Enter]
Description
Dynamic DDS enabled
Dynamic DDS disabled (default)
17
VS0201 / VS0401 User Manual
Pushbutton Lock Command
The Pushbutton Lock feature allows you to secure your device by locking use of the front panel pushbuttons.
The formula for the Pushbutton Lock command is as follows:
1. Pushbutton Lock Command + Control [Enter]
For example, to disable use of the front panel pushbuttons, type the following:
button off [Enter]
The following tables show the possible values and formats for the Control command:
Command
button
Description
Pushbutton Lock command
Control
on off
Description
Enable front panel pushbuttons
(default)
Disable front panel pushbuttons:
Source port LED flashes every 1 second to indicate pushbuttons are locked
Note: Each command can be separated with a space.
The following table lists the available commands:
Command
button
Control
on off
Enter
[Enter]
[Enter]
Description
Front panel pushbuttons enabled (default)
Front panel pushbuttons disabled
18
Chapter 3. Operation
Read Firmware Command
The Read Firmware feature allows you to read the firmware information of the
VS0201 / VS0401.
The formula for the Read Firmware command is as follows:
1. Read Firmware Command + Control [Enter]
For example, to display the firmware information, type the following:
read version [Enter]
The following tables show the possible values and formats for the Read
Firmware formulas:
Command
read
Description
Read Firmware command
Control
version
Description
Read device firmware version
Note: Each command can be separated with a space.
The following table lists the available commands:
Command
read
Control
version
Enter
[Enter]
Description
Read device firmware version
19
VS0201 / VS0401 User Manual
Reset Command
The Reset feature resets the device back to the factory default settings. The reset function does not effect the on/off power status of the device.
The formula for the Rest commands is as follows:
1. Reset Command [Enter]
For example, to reset back to the factory default settings, type the following:
reset [Enter]
The following table shows the value for the formula:
Command
reset
Description
Reset command
Note: Each command can be separated with a space.
The following table lists the available commands:
Command
reset
Enter
[Enter]
Description
Reset the device back to the factory default settings
20
Chapter 3. Operation
Baud Rate Command
You can select the RS-232 Baud Rate you want the VS0201 / VS0401 to use.
Options are 9600, 19200 (default), and 38400.
The formula for the Baud Rate command is as follows:
1. Baud Rate Command + Control [Enter]
For example, to select 38400 as your baud rate, type the following:
baud 38400 [enter]
The following tables show the possible values and formats for the Baud Rate formulas:
Command
baud
Description
Baud Rate command
Control
9600
19200
38400
Description
Use 9600 baud rate
Use 19200 baud rate (default)
Use 38400 baud rate
The following table lists the available commands
:
Command
baud
Control
9600
Enter
[Enter]
19200
38400
[Enter]
[Enter]
Description
Sets the baud rate to
9600
Sets the baud rate to
19200
Sets the baud rate to
38400
21
VS0201 / VS0401 User Manual
This Page Intentionally Left Blank
22
Chapter 4
The Firmware Upgrade Utility
Introduction
The purpose of the Windows-based Firmware Upgrade Utility is to provide an easy process for upgrading the VS0201 / VS0401. The program comes as part of a Firmware Upgrade Package that is specific for each device.
As new firmware versions become available, new firmware upgrade packages are posted on our website. Check the website regularly to find the latest information and packages.
Downloading the Firmware Upgrade Package
To download the firmware upgrade package:
1. On our Website go to: Download - Firmware and choose the device model, or from the VS0201 / VS0401 product page under the Resources tab, select Firmware. A list of available firmware upgrade packages appears.
2. Choose the firmware upgrade package that you wish to install (usually the most recent) and download it to your computer.
23
VS0201 / VS0401 User Manual
Preparation
To prepare for the firmware upgrade, do the following:
1. Use an RS-232 cable to connect a COM port on your computer to the RS-
232 Serial Port of your VS0201 / VS0401.
2. Unplug the VS0201 / VS0401’s power adapter.
3. Hold-down front panel pushbutton 1 and plug the power adapter into the
VS0201 / VS0401 to power the unit.
4. If successful,
The VS0201 / VS0401’s port 1 and port 2 LEDs will start flashing and you can start the upgrade process as explained on the next page.
24
Chapter 4. The Firmware Upgrade Utility
Starting the Upgrade
To upgrade the firmware:
1. Run the downloaded firmware upgrade package file either by doubleclicking the file icon, or by opening a command line and entering the full path to it.
The Firmware Upgrade Utility welcome screen appears:
Note: The screens shown in this section are for reference only. The wording and layout of the actual screens put up by the Firmware
Upgrade Utility may vary slightly from these examples.
2. Read and Agree to the License Agreement (click the I Agree radio button).
(Continues on next page.)
25
VS0201 / VS0401 User Manual
(Continued from previous page.)
3. Click Next to continue. The Firmware Upgrade Utility main screen appears. The devices capable of being upgraded are listed in the Device
List panel:
4. Click Next to perform the upgrade. The port 1 and port 2 LEDs will flash while the upgrade is in process.
If you enabled Check Firmware Version, the Utility compares the device's firmware level with that of the upgrade files. If it finds that the device's version is higher than the upgrade version, it brings up a dialog box informing you of the situation and gives you the option to continue or cancel.
26
If you didn't enable Check Firmware Version, the Utility installs the upgrade files without checking whether they are a higher level, or not.
Status messages appear in the Status Messages panel, and the progress toward completion is shown on the Progress bar.
Chapter 4. The Firmware Upgrade Utility
Upgrade Succeeded
After the upgrade has completed, all port LEDs will stop flashing and a screen appears to inform you that the procedure was successful:
Click Finish to close the Firmware Upgrade Utility.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
27
VS0201 / VS0401 User Manual
Firmware Upgrade Recovery
There are three conditions that call for firmware upgrade recovery:
When a firmware upgrade is manually aborted.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the device.
2. Connect the RS-232 cable to the RS-232 Serial Port.
3. Repeat the upgrade procedure.
28
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V phase-to-phase voltage.
To prevent damage to your installation it is important that all devices are properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/national wiring codes.
Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.
29
VS0201 / VS0401 User Manual
If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or un-interruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing rests on any cables.
Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need for service.
The device does not operate normally when the operating instructions are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
30
Appendix
Technical Support
International
For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com
For telephone support, Telephone Support, page iii
North America
Email Support
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
Telephone Support [email protected]
http://www.aten-usa.com/support
1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operating system, revision level, expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
31
VS0201 / VS0401 User Manual
Specifications
Function
Display Connections
Connectors Input Video
Audio
Output
Switches
LEDs
RS-232 Port
IR Input port
Power
Port Selection
Power
Selected
Power
Video
Power Consumption
Environment Operating Temp.
Storage Temp
Humidity
Physical
Properties
Housing
Weight
Dimensions
(L x W x H)
Video
Audio
VS0201 VS0401
2
2 x HDB-15 Male (Blue)
2 x Mini Stereo Jack
Female (Green)
1 x HDB-15 Female
(Blue)
4
4 x HDB-15 Male (Blue)
4 x Mini Stereo Jack
Female (Green)
1 x HDB-15 Female
(Blue)
1 x Mini Stereo Jack
Female (Green)
1 x Mini Stereo Jack
Female (Green)
1 x DB-9 Female (Black)
1 x Mini Stereo Jack Female (Black)
2 x Pushbuttons
1 x DC Jack
4 x Pushbuttons
1 x Pushbutton
2 x (Green) 4 x (Green)
1 x (Green / Orange)
1920x1440 @ 30 m
1280x1024 @ 65 m
DC5.3V, 0.6W
0–50ºC
-20–60ºC
0–80% RH, Non-condensing
Metal
0.45kg
13 x 7.61 x 4.2 cm
0.66kg
20 x 7.61 x 4.2 cm
32
Appendix
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or update. For further inquiries, please contact your direct vendor.
33

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Displays the video output of four computers on a single monitor or projector
- Quick and easy switching between VGA/Audio sources via front panel pushbuttons, RS-232, or IR remote control
- Superior video quality – up to 1920 x 1440
- Long-distance transmission – up to 30 m *
- Supports VGA, SVGA, UXGA, WUXGA and multisync monitors
- Video DynaSync™ – Exclusive ATEN technology eliminates boot-up display problems and optimizes resolution when switching between ports
- Built-in bi-directional RS-232 serial port for high-end system control **
- RS-232 Control:
- • Power On Detection – if one VGA source is powered off, the VS0401 will automatically switch to the next powered-on
- source