D10 Electronic Configuration: Pocket Guide

D10 Electronic Configuration: Pocket Guide
Prior to commissioning the system, please ensure that you
have connected the wiring of all components in the system to
the controller terminals correctly. Kindly refer to the diagrams
provided on the back of this document for details.
1. If powering up the system
ex-factory, it will request for
the operating Profile
(operating standard) to be
set.
&
ZA: Standard profile for
South Africa
&
CE: Standard profile for
the European Union
&
UL325: Standard profile
for the USA compliant
with requirements but not
certified
2. Select the Profile that will
suit the specific region from the list. With this set, the system will
automatically proceed to the Limit Setup Menu. Follow the
onscreen instructions to complete the setup procedure.
3. If powering up at any stage after this, push and hold the oblong
enter button ( ) for two seconds. Select the Limits Menu by
pressing the enter button ( ). Follow the onscreen instructions to
complete the setup procedure.
Section 3 below provides the full menu of features that can be set up
on the system.
An explanation of each feature is provided in Section 21, Controller
Features of the full installation manual available on
www.centsys.co.za.
When setting up the D5-Evo and D10 system via the LCD display, all
the steps that have to be followed are clearly provided via the display.
It is only necessary to note the following:
&
To get into Setup Mode, press the (
follow the instructions provided
) button for two seconds and
&
The buttons provided on the controller for navigating the system are
not marked because at each step during the setup, the function
given to each button is provided on the display
&
When not in Setup Mode, i.e. Normal Mode, the (
used as a test button for operating the system
&
The triangular up or down (
the diagnostic screens
) button is
) buttons are used to scroll through
&
For each feature a Factory Default Setting has been programmed
into the controller. Referred to as an Operating Standard or
Profile, these defaults have been determined to suit the
requirements of the specific region where the installation is being
carried out. It is only necessary to change a feature where the
default does not suit the installation. When selecting any feature in
the menu, details of the current setting stored in the controller are
displayed
The schedule of Factory Defaults are detailed in the full
installation manual, available for download on
www.centsys.co.za
Icon
Menu
1.
Sub-menu
1.1. Setup wizard
Setting limits
2.
Safety
2.1. Collision force
2.2.
2.3.
2.4.
2.5.
Collision count
Alarm output
LCK input as ESTOP
External gate
indication status
3.
3.1.
3.2.
3.3.
3.4.
Autoclose
Autoclose Status
Autoclose Timer
Autoclose Override
Autoclose advanced
options
4.
Modes of operation
4.1. Operating mode
5.
Run profile
5.1. Positive Close Mode
5.2. Pre-open delay
5.3. Pre-close delay
5.4 Opening speed
5.5. Closing speed
5.6. Ramp-up distance
5.7. Ramp-down distance
5.8. TRG stop distance
5.9. IRB stop distance
5.10.Crawl distance
5.11.Torque limit
2.1.1. Opening collision force
2.1.2. Closing collision force
2.5.1.
2.5.2.
2.5.3.
2.5.4.
2.5.5.
2.5.6.
2.6.7.
2.5.8.
2.5.9.
Indicator output
Closed indication
Part close indication
Closing indication
Part open indication
Opening indication
Open indication
Pedestrian indication
Unknown indication
3.4.1.
3.4.2.
3.4.3.
Autoclose fully open
Autoclose partly open
Autoclose partly closed
4.1.1.
4.1.2.
4.1.3.
4.1.4.
4.1.5.
Standard Mode
Condominium Mode
Reversing Mode
PLC
Deadman Control Mode
5.1.1. Positive Close Mode Status
5.1.2. Positive Close Mode Force
Icon
Menu
6.
Infrared beams
6.1. PIRAC control
Sub-menu
6.1.1. PIRAC status
6.1.2. Stop on open
6.1.2.1.
6.1.2.2.
6.2. IR beam test
Stop on open
status
Stopping
distance
6.2.1. On/Off
6.2.2. Test beam selection
(IRBC; IRBO; IRBC
and IRBO)
6.3. IRBO=IRBC on closing
6.4. IR beam alarms
6.4.1. Ambush Alarm
6.4.1.1. Ambush Alarm
on/off
6.4.1.2. Broken IRB time
6.4.2. Break-in Alarm on/off
6.4.3. Alarm output selection
7.
7.1.
7.2.
7.3.
7.4.
Pedestrian
Pedestrian open position
Pedestrian Autoclose time
Pedestrian pre-open delay
Pedestrian pre-close delay
8.
Courtesy Light
8.1. Courtesy Light Timer
8.2. Light Profile
9.
ChronoGuard
9.1. Time and date
9.2. Time-Periods
8.2.1.
8.2.2.
8.2.3.
8.2.4.
Courtesy
Pre-flash
Pre-flash
Pre-flash
Light
A
B
C
9.2.1. Add Time-period
9.2.1.1. Auto function
9.2.1.2. Time-bar
function
9.2.2. Delete Time-period
9.2.3. Edit review Time-periods
9.3. Exclusions
9.3.1. Add exclusion
9.3.1.1. Auto function
9.3.1.2. Time-bar
function
9.3.2. Delete exclusion
9.3.3. Edit review exclusions
9.4. Delete all Time-periods
and exclusions
Icon
Menu
10. General settings
10.1.Operating standard
(ZA; CE; UL325)
10.2.Reset options
Sub-menu
10.2.1. Factory defaults
10.2.2. Delete all remotes
10.2.3. Delete all Time-periods
and exclusions
10.2.4. Reset all
10.3.Diagnostic screen on/off
10.4.Test button
disabled/enabled
10.5.Backup EEPROM
10.6.Restore EEPROM
11. Remote controls
Press button of
valid transmitter
(if menu locked)
11.1.Add remotes
11.2.Delete remotes
11.2.1.
11.2.2.
11.2.3.
11.2.4.
11.2.5.
11.3.Edit remote button
11.4.Autolearn
11.5.Lock Tx menu
11.6.Onboard receiver
enable/disable
Delete remote by ID
Delete remote button
Delete remote by
button
Delete not present
On/Off
Delete all remotes
4. Diagnostic LEDs
The D5-Evo and D10 controllers have a series of diagnostic LEDs
which indicate the state of the inputs.
Normally-open inputs are indicated by a red LED, and normally-closed
inputs by a green LED.
An illuminated red LED indicates that the signal is present
(e.g. intercom button pressed), while a non-illuminated green LED
indicates that the signal is absent (e.g. IRB broken).
Safety Close - green LED
On when the closing beam
is not activated
Safety Open - green LED
On when the opening
beam is not activated
Lck/Stp - green LED
On when the Lck/Stp
input is not activated
Trg - red LED
On when the trigger signal
is present
Ped - red LED
On when the pedestrian
signal is present
FRX - red LED
On when a free-exit
signal is present
Aux - red LED
On when an auxiliary
signal is present
Status- red LED
This LED indicated the status of
the gate as per the table below:
LED indication
Gate status
Off
Gate is closed
On
Gate is partially or fully open
Continuous slow flash
Gate is opening
Continuous fast flash
Gate is closing
One flash every two seconds
Pillar Light Override is activated
Two flashes every two seconds
No mains present
LED indication
Gate status
Three flashes every two seconds
Battery voltage is low
Four flashes every two seconds
Multiple collisions have occurred
The LCD display shows useful information regarding the status of the
system.
1. Battery icon
Indicates the state of charge of the battery.
&
Four solid bars = full capacity
&
Two solid bars = 50% capacity
&
No solid bars, with the icon flashing = battery empty
2. Mains icon
Displays the presence or absence of mains voltage:
&
Plug solid = mains present and battery charging
&
Plug hollow and flashing = No mains present and battery not
charging
3. Autoclose information
&
Displays the state of the Autoclose function
&
Displays off if Autoclose is not selected
&
OVR if Autoclose is overridden, and the remaining Autoclose
time if Autoclose is active
&
POVR indicates that the PIRAC option is overriden
4. Pillar light information
&
Displays the remaining light time if Courtesy Light Mode is
selected
&
Pre-flashing mode is displayed if pre-flash is selected
&
LIT will be indicated if the pillar light has been turned on
permanently
A warning buzzer will sound (where applicable) as per the table below:
Number of beeps
Fault type
Gate
continues
to operate
User can
correct
error
Break-in alarm
Continuous tone for 30 seconds
Alarm
N/A
N/A
Ambush alarm
Continuous tone until IRBs are cleared
Alarm
N/A
N/A
Periodic until condition is cleared by user (500/500ms)
Collision
No
Yes
Three beeps periodically for 30 seconds
Power system fault
Yes*
Yes
Auxiliary overload
Five beeps periodically for 30 seconds
Hardware
No
No
Holiday Lockout
One beep periodically for 30 seconds
User
No
Yes
Emergency stop
Inhibitor name
Multiple collision
Battery low
Priority
One beep periodically for 30 seconds
User
No
Yes
Time-barring
One beep periodically for 5 seconds
User
No
Yes
No limits set
Three short beeps for 5 seconds
Lost
No
Yes
Mains failure
Two beeps periodically for 30 seconds
Power system fault
Yes
Yes
Beams broken (any)
One beep periodically for 30 seconds
User
No
Yes
Beams failure
Five beeps periodically for 30 seconds
Hardware
No
No
DOSS disconnected
Five beeps periodically for 30 seconds
Hardware
No
No
Fuse blown
Five beeps periodically for 30 seconds
Hardware
No
Yes
Motor disconnected
Five beeps periodically for 30 seconds
Hardware
No
Yes
Bridge damaged
Five beeps periodically for 30 seconds
Hardware
No
No
Gate stalled
Four beeps periodically for 10 seconds
Collision
No
Yes
Periodic while gate runs(500/500ms)
Lost
Yes
Yes
No magnet detected
Gate will close fully and then shutdown for two minutes
1.
Always check that the circuit breaker in the
electrical panel is in the OFF position, and that
all high voltage circuits (more than 42.4V) are
completely isolated from the mains supply
before doing any work.
2.
Ensure that all low voltage systems (less than 42.4V) are
suitably protected from damage, by disconnecting all
sources of power such as chargers and batteries before
doing any work.
3.
All electrical work must be carried out according to the
requirements of all applicable local electrical codes. (It is
recommended that a licensed electrical contractor perform
such work).
Connect all wiring
Connect the controller to the required input and output devices as per
the wiring diagram on the right hand side.
Light/Light
Pillar light connection. (A normally-open
potential-free input)
Safe Common
Used for switching the power supply to the safety
beams, if automatic beam testing is required
Aux 12V Out
Auxiliary power connection. Provides +12V DC
supply for auxiliary equipment such as a radio
receiver, photo cells, etc. It is electronically limited
to 300mA
Safety Close
Closing beam safety input. (A normally-closed
potential-free input)
Safety Open
Opening beam safety input. (A normally-closed
potential-free input)
Lck/Stp
Holiday Lockout or emergency stop input.
(A normally-closed potential-free input)
Trg
Trigger input. (A normally-open potential-free
input)
FRX
Free-exit input. (A normally-open potential-free
input)
Aux
Activates the pillar light relay. (A normally-open
potential-free input).
Ped
Pedestrian opening input. (A normally-open
potential-free input)
Com
Common termination point. All trigger signals,
etc. have their return path to one of the Com
terminals
Status
External gate status indicator. (A low current
output signal). An output terminal which provides a
low current, drive (approx. 4,5V DC, 20mA) to a
LED which can be used to indicate the gate status
remotely)
Aux IO
The Aux IO terminal provides an open collector
output which can be used for alarm or auto function
purposes
Motor
Motor output – connects to the thick blue motor
wire
Motor
Motor output – connects to the thick black motor
wire
12V/24 +
Positive battery connection.
Battery terminal normally indicated as + or
red (right hand battery)
12V/24 -
Negative battery connection.
Battery terminal normally indicated as - or
black (left hand battery)
12V/24V this will either be 12V or 24V depending on the motor
voltage of the operator
Latched
A switch that remains in a connected or
disconnected state similar to a standard light switch
Non-Latched
A switch that momentarily makes contact, and may
be spring loaded similar to a push button door step
Once the installation has been successfully completed and tested, it is
important for the installer to explain the operation and safety
requirements of the system.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement