WAUS Power Supplies Core Assortment Catalogue 2015 Issue #3
ISSUE #3
Switch-mode and uninterruptible power supplies
Core Assortment Catalogue 2015
Australia & New Zealand
www.weidmuller.com.au
Would you accept a power failure in your application?
Our power supply solutions are never-ending!
Machinery
Transportation
INSTAPOWER
PRO-E
PROeco
For applications wherever space and
efficiency is the overall requirement
For OEM applications where DIN rail is
not used
For General purpose applications
•• Building
•• Very small control cabinets for
machinery
•• Terminal boxes
•• Consumer machines
•• Electronic signs
•• Custom design
•• Process (e.g Instrumentation)
•• Machinery (e.g. control system)
•• Energy (e.g. SCADA system)
•• Transportation (e.g. signalling)
DIN rail mount
Page 20
Chassis mount
Page 18
DIN rail mount
Page 8
Energy
Process
PROmax
DC UPS
PRO-H
Use in demanding applications where
varying loads or high temperatures
exist
Energy Storage to bridge 24VDC
supplies during mains power
interruptions
For applications where reliability is
paramount. Active redundancy with
ATEX approvals.
•• Process (e.g. Water treatment)
•• Machinery (e.g. Conveying systems)
•• Energy (e.g. Renewable energy)
•• Transportation
•• Process (e.g. Water treatment)
•• Machinery (e.g. Conveying systems)
•• Energy (e.g. Renewable energy)
•• Transportation
•• Process (Oil & Gas, chemical)
•• Energy
DIN rail mount
Page 10
DIN rail mount
Page 12
DIN rail mount
Page 16
Find the perfect product to meet your requirement
Our extensive portfolio of power supplies at a glance
NO = NO contact
CO = CO contact
Start-up @ –40°C = In the range of –40 to –25°C the device starts, but some technical parameter may differ (i. e., ripple-voltage).
%
u
%
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Order No.
Marine engineering
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Power distribution
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Simple process applications
●
●
●
●
●
●
●
●
●
●
●
●
●
Energy technology
%
●
●
●
●
●
●
●
●
●
●
●
●
●
Process industry
●
87
●
87
●
90
●
91
●
93
●
87
–25
●
88 > 0.5 II
to
●
+70
89
●
90
●
90
●
90
●
90
●
90
●
90
●
90
●
91
●
91
●
–25 91.5
●
to 92.5
●
90
+70
●
91
> 0.5 III
●
91.5
SEMI F47
● Start-up 92.5
@
●
86
● –40°C 89
●
89
Cl1Div2
●
91
●
91.5
Some not yet awarded
●
92.5
(status July 2014)
82
85
85
85
88
87
–25
89
to
> 1.8 II
87
+70
90
89
91
88
Cl1Div2
88
88
Machine construction and plant manufacture
Approvals
Surge category
MTBF time [Mh]
Efficiency [%]
Temperature range [°C]
Side-by-side connectability
Status relay
Power boost [60 s]
Derating at [°C]
Power rating [V]
Rated current [A]
NO
24 3 72
NO
24 5 120
NO
24 10 240
NO
24 20 480
NO
24 40 960
NO
24 5 120
NO
24 10 240 > 55
NO
24 20 480
NO
24 40 960
NO
12 6 72
NO
12 10 120
NO
48 5 240
NO
48 10 480
CO
24 3 72
CO
24 5 120
CO
24 7.5 180
CO
24 10 240
CO
24 20 480
CO
24 40 960
24 5 120
120% CO
CO
24 10 240
> 60
300% CO
24 20 480
@ 1 s CO
24 40 960
CO
5 14 70
CO
12 6 72
CO
12 10 120
CO
48 5 240
CO
48 10 480
CO
48 20 960
NO
12 6 70
NO
12 12 140
NO
24 3.8 90
NO
24 3.8 90
NO
24 7.5 180
NO
24 15 360
NO
24 25 600
> 40
NO
48 2 96
NO
48 4 192
NO
48 7.5 360
NO
48 12.5 600
NO
24 7.5 180
NO
24 15 360
NO
24 25 600
Recommendation for application
Field cabinets
80–370
80–370
80–370
80–370
80–370
450–870
450–870
450–870
450–870
80–370
80–370
80–370
80–370
80–370
80–370
80–370
80–370
80–370
80–370
450–800
450–800
450–800
450–800
80–370
80–370
80–370
80–370
80–370
80–370
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
Additional functions
Small and series machine construction
85–264
85–264
85–264
85–264
85–264
340–575
340–575
340–575
340–575
85–264
85–264
85–264
85–264
85–277
85–277
85–277
85–277
85–277
85–277
3 x 320–3 x 575
3 x 320–3 x 575
3 x 320–3 x 575
3 x 320–3 x 575
85–277
85–277
85–277
85–277
85–277
85–277
85–264
85–132/187–264
85–264
85–264
85–132/187–264
85–132/187–264
85–132/187–264
85–264
85–132/187–264
85–132/187–264
85–132/187–264
85–132/187–550
85–132/187–550
85–132/187–550
Rated voltage [V]
1
1
1
1
1
3
3
3
3
1
1
1
1
1
1
1
1
1
1
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
Output side
DC input voltage [V]
PRO ECO 72 W 24 V 3 A
PRO ECO 120 W 24 V 5 A
PRO ECO 240 W 24 V 10 A
PRO ECO 480 W 24 V 20 A
PRO ECO 960 W 24 V 40 A
PRO ECO3 120 W 24 V 5 A
PRO ECO3 240 W 24 V 10 A
PRO ECO3 480 W 24 V 20 A
PRO ECO3 960 W 24 V 40 A
PRO ECO 72 W 12 V 6 A
PRO ECO 120 W 12 V 10 A
PRO ECO 240 W 48 V 5 A
PRO ECO 480 W 48 V 10 A
PRO MAX 72 W 24 V 3 A
PRO MAX 120 W 24 V 5 A
PRO MAX 180 W 24 V 7,5 A
PRO MAX 240 W 24 V 10 A
PRO MAX 480 W 24 V 20 A
PRO MAX 960 W 24 V 40 A
PRO MAX3 120 W 24 V 5 A
PRO MAX3 240 W 24 V 10 A
PRO MAX3 480 W 24 V 20 A
PRO MAX3 960 W 24 V 40 A
PRO MAX 70 W 5 V 14 A
PRO MAX 72 W 12 V 6 A
PRO MAX 120 W 12 V 10 A
PRO MAX 240 W 48 V 5 A
PRO MAX 480 W 48 V 10 A
PRO MAX 960 W 48 V 20 A
CP T SNT 70 W 12 V 6 A
CP T SNT 140 W 12 V 12 A
CP T SNT 90 W 24 V 3.8 A
CP T SNT 90 W 24 V 3.8 A CL2
CP T SNT 180 W 24 V 7.5 A
CP T SNT 360 W 24 V 15 A
CP T SNT 600 W 24 V 25 A
CP T SNT 90 W 48 V 2 A
CP T SNT 180 W 48 V 4 A
CP T SNT 360 W 48 V 7.5 A
CP T SNT 600 W 48 V 12.5 A
CP T SNT2 180 W 24 V 7.5 A
CP T SNT2 360 W 24 V 15 A
CP T SNT2 600 W 24 V 25 A
AC input voltage [V]
Phases
Input side
Description
PRO-H
PROmax
PROeco
Series / family
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
1469470000
1469480000
1469490000
1469510000
1469520000
1469530000
1469540000
1469550000
1469560000
1469570000
1469580000
1469590000
1469610000
1478100000
1478110000
1478120000
1478130000
1478140000
1478150000
1478170000
1478180000
1478190000
1478200000
1478210000
1478220000
1478230000
1478240000
1478250000
1478270000
1105430000
1105440000
1105790000
1194410000
1105810000
1105820000
1105840000
1194420000
1105850000
1105860000
1105870000
1194480000
1194490000
1194310000
INSTAPOWER
Supplementary modules
UPS
CP DC BUFFER 24 V 20 A
Status relay
Parallel connection option
Side-by-side connectability
24
22.5–29.5
10
240
●
≤5
●
22.5–30
24
20
1313320010
–25
to
+70
480
●
●
●
1370050010
●
1370040010
CP DC UPS 24 V 20 A/10 A
20–30
Uin–0.3 V
20/10
480/240
●
CP DC UPS 24 V 40 A
20–30
Uin–0.3 V
40
960
●
24
24
24
24
24
10 A / 11.3 min.
10 A / 11.3 min.
10 A / 26.5 min.
10 A / 51 min.
10 A / 81 min.
1.3 Ah
3.4 Ah
7.2 Ah
12 Ah
17 Ah
CP A BATTERY 24 V DC 1,3 Ah
CP A BATTERY 24 V DC 3,4 Ah
CP A BATTERY 24 V DC 7,2 Ah
CP A BATTERY 24 V DC 12 Ah
CP A BATTERY 24 V DC 17 Ah
Order No.
Approvals (all CE)
Power rating [W]
18–31.2
Temperature range [°C]
Rated current [A]
Additional functions
Adjustable range [V]
CP DCDC 250 W 24 V 10 A
Output
Rated voltage [V]
AC input voltage [V]
Input
DC input voltage [V]
DC/DC
Description
Series / family
≤2
≤2
≤2
≤2
≤2
●
●
●
●
●
CP T RM 10 (PRO-H redundancy module)
24
24
24–27
15
●
CP T RM 20 (PRO-H redundancy module)
24
24
24–27
25
●
CP DM 10 (diode module)
10–40
UIN–0.7
10
CP DM 20 (diode module)
10–40
UIN–0.7
20
CP M DM 20 (diode module)
18–30
UIN–0.7
20
●
≤5
●
CP M DM 40 (diode module)
18–30
UIN–0.7
40
●
≤5
●
CP M CAP (capacity module)
18–30
UIN
40 A/1 ms
●
≤5
●
1
1
1.5
1.5
2
28
24
22.5
18
10
0
to
+40
–25
to
+70
–10
to
+55
●
●
●
●
●
CP SNT 24 W 28 V 1 A
CP SNT 24 W 24 V 1 A
CP SNT 24 W 15 V 1,5 A
CP SNT 24 W 12 V 1,5 A
CP SNT 24 W 5 V 2 A
85–265
85–265
85–265
85–265
85–265
120–300
120–300
120–300
120–300
120–300
28
24
15
12
5
CP SNT 25 W 5 V 5 A
85–264
110–370
5
4–8
5
25
≤3
●
CP SNT 48 W 12 V 4 A
85–264
110–370
12
9–15
4
48
≤3
●
CP SNT 48 W 24 V 2 A
85–264
110–370
24
15–28
2
48
≤3
●
CP SNT 48 W 48 V 1A
85–264
110–370
48
46–55
1
48
≤3
●
1251220000
1406930000
1251070000
1251080000
1251090000
1251110000
1105880000
1105890000
8710620000
8768650000
1222210000
–25
to
+70
1222220000
1222240000
–20
to
+50
9928890028
9928890024
9928890015
9928890012
9928890005
8754960000
–10
to
+70
8754970000
8739140000
8879230000
We cannot guarantee that the publications or software we provide to customers for the purpose of placing orders are completely free of errors. We make every effort to correct such errors once we become aware of them.
Product Overview
Power Supply Distribution
As an industrial connectivity partner, Weidmüller offers you power supply solutions in
a variety of reliability levels – which accurately fit into your application right down to
the very last detail.
Input/supply
Lightning and surge protection
AC distribution
Switched-mode power supply units
PROeco
Upstream protective circuit for the
AC input: modular terminals for a
flexible connection to the mains
and our VARITECTOR lightning and
surge protectors for supplementary
or complete protection of your power
supply.
PROmax
Expansion modules
PRO-H
Diode module
System components
Capacity module
The correct switched-mode power
supply unit is an essential element of
a permanently reliable cabinet and
supplies the fuel for all the automation
equipment. The expansion modules
allow you to supplement individual
functions.
Electronic fuse
Depending on which requirements the
devices in your automation have and
how they are protected or supported
in a customised manner, the system
components turn your power supply
into a solution for your application.
Uninterruptible power supply (UPS)
Distribution
DC/DC converters
WAVEGUARD
PRV Terminal
Distribution of the DC control voltages
for the individual consumer paths.
Control energy distribution
Marshalling and potential distribution
Contents
Power Supplies
8
NEW
PROeco
16
• High reliability in a compact size.
• 12 - 48V, 72 – 960W
• 1 or 3 phase operation
10
NEW
PROmax
• High performance with extended life
• 12-48V, 70-600W
• Active redundancy system
18
DC UPS and Battery Modules
20
• Secure DC energy for automation
• Intuitive UPS
• High quality battery system
14
DC Buffer Module
DC/DC converter
• Isolate and regulate 24V DC power
Weidmüller product portfolio
Weidmüller offers a comprehensive range of products for electrical
connectivity, transmission and conditioning of power, signal and data
in industrial environments. See our website at
www.weidmuller.com.au for more information about our products.
INSTAPOWER
• Powerful and efficient in small spaces
• Din Rail mount
• 25-48W
21
• Maintenance free power storage
• Short duration with high operating
temperature
15
NEW
PRO-E
• Power for alternative systems
• Plate mount
• 5-48V, 25-350W
• Maximum power with minimal size
• 5 - 48V, 72 – 960W
• 1, 2 or, 3 phase operation
12
PRO-H
Electronic Fusing
• Electronic fusing with advantages
• Fast switching, local and remote
reset
21
Fuse Terminals
• Overload and short-circuit protection
Power Supply Selection Considerations/Glossary
For Power Supply Applications and Glossary
please see pages 22-26.
Switched-mode power supply units connectPower PROeco
NEW
Tackle your power supply economically
PROeco bundles all of the basic functions in a compact design
Noticeably energy-saving
A high degree of efficiency of up to 93 % and
minimal no-load losses ensure low energy
consumption and a long service life.
A
B
C
93 %
Rapid status diagnosis
The tricolour LED display and an
integrated status relay make it easier
to analyse statuses and errors during
commissioning and operation.
D
Robust and reliable
PROeco power packs work reliably in a wide
temperature range from –25 °C to +70 °C
and boast a high MTBF value of more than
500,000 hours.
Extremely compact
With a max. depth of 120 mm, PROeco power
supplies even fit into small cabinets.
The compact design also saves up to 50 %
space in the cabinet.
8
Power supply solution
Together with the uninterruptible DC USP,
the diode modules or CAP modules, you
can create a power supply solution that is
tailored to your requirements.
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
Switched-mode power supply units connectPower PROeco
PROeco power supplies
With basic functionality and a high level of reliability
Provides a complete range
•• Single and three-phase switch-mode power supply units
•• 12V, 24V, 48V models
•• Slim design
•• Large temperature range from –25 °C to 70 °C
•• The output voltage can be precisely adjusted via the multi
turn potentiometer on the front
•• Remote monitoring via integrated status relay
•• Tricoloured LED indicators for simple error detection
•• Advanced visual warning at 90 % and 100% rated output
•• International approvals: CE; TÜV (EN/IEC 60950-1);
cULus, RCM
Ambient temp. operating
–25 °C…+70 °C
Storage temperature
Max. perm. air humidity (operation)
Degree of protection
Class of protection
Pollution degree
Insulation voltage input/output
MTBF
Parallel connection option
Housing version
–40 °C…+85 °C
5 %…95 % RH
IP 20
I, with PE connection
2
3 kV E/A / 2 kV E/earth / 0.5 kV A/earth
> 500.000 h acc. to IEC 1709 (SN29500)
yes, max. 5 without diode module
metal, corrosion resistant
Mounting position, installation notice horizontal on mounting rail TS 35, 50 mm spacing
top and bottom for free air circulation
Short-circuit protection
Overload protection
Yes, automatic restart
Yes, IU characteristic curve
Overtemperature protection
Yes, automatic restart
EMC / shock / vibration
Noise emission acc. to EN55022
Class B
Noise immunity tests acc. to
EN61000-4-2 (ESD),
EN61000-4-3 and EN61000-4-8 (Fields),
EN61000-4-4 (Burst), EN61000-4-5 (Surge),
EN61000-4-6 (conducted), EN61000-4-11 (Dips)
Limiting of mains voltage
harmonic currents
Acc. to EN61000-3-2
Resistance against vibration
and shock
1 g acc. to EN50178, shock: 15 g in all directions
Electrical safety (applied standards)
\
Derating curves
Electrical equipment of machines
Acc. to EN60204
Safety transformers for
switched-mode power units
Acc. to EN61558-2-17
Machinery with
electronic equipment
Acc. to EN50178 / VDE0160
Safety extra-low voltage
Protective separation
Protection against electrical shock
SELV acc. to EN60950-1, PELV acc. to EN60204-1
VDE0100-410
Acc. to DIN57100-410
Protection against dangerous
shock currents
Acc. to VDE0106-101
Note: Adjustable output voltage - 12V: 10...16V, 24V: 22...28V, 48V: 42...56V
≤ 480 Watt
120
100
100
80
80
60
40
60
40
20
20
0
–25
960 Watt
120
Ioutput (% IN)
General technical data
Ioutput (% IN)
Technical data
%
0
20
30
40
50
Ambient temperature (°C)
60
70
0
–25
0
20
30
40
50
Ambient temperature (°C)
70
PROeco
Ordering Data
Single-phase
N. Voltage N. Current
PRO ECO 72W
24V
3A
PRO ECO 120W 24V
5A
PRO ECO 240W 24V
10A
PRO ECO 480W 24V
20A
PRO ECO 960W 24V
40A
PRO ECO 72W
12V
6A
PRO ECO 120W 12V
10A
PRO ECO 240W 48V
5A
PRO ECO 480W 48V
10A
Three-phase
PRO ECO3 120W 24V
5A
PRO ECO3 240W 24V
10A
PRO ECO3 480W 24V
20A
PRO ECO3 960W 24V
40A
Diode module 24V only
CP DM 10
2 x 10 A
CP DM 20
2 x 20 A / 1 x 40 A
60
H x W x D/ Weight
125/34/100 mm/ 0.5 kg
125/40/100 mm/ 0.6 kg
125/60/100 mm/ 1 kg
125/100/120 mm/ 1.6 kg
125/160/120 mm/ 2.9 kg
125/34/100 mm/ 0.6 kg
125/40/100 mm / 0.7 kg
125/60/100 mm / 1 kg
125/100/120 mm/ 1.6 kg
1469470000
1469480000
1469490000
1469510000
1469520000
1469570000
1469580000
1469590000
1469610000
125/40/100 mm/ 0.6 kg
125/60/100 mm / 1 kg
125/100/120 mm/ 1.3 kg
125/160/120 mm/ 2.5 kg
1469530000
1469540000
1469550000
1469560000
125/55.5/110 mm/ 399 g
125/55.5/110 mm/ 411 g
8710620000
8768650000
*N. = Nominal
9
connectPower PROmax switched-mode power supply unit
NEW
Powerful power supply for machines and systems
PROmax offers flexible solutions for ambitious automation
Space-saving width
With extremely small width and direct side-by-side
fitting, minimal space is required on the DIN rail.
Robust and reliable supply
MTBF values exceeding 500,000 hours and a
wide temperature range of –25 °C to +70 °C
ensure reliable supply of the systems. Start-up
temperatures of –40 °C make the PROmax
particularly robust.
Universal application
Variants with 3 A to 40 A output current, output
voltages of 5 V DC to 48 V DC and numerous
approvals (e.g. GL, UL, Class I, Div. 2) enable
universal application solutions the world over.
Powerful
Continuous output power of up to 120 % at
temperatures up to +45 °C and high output
peaks up to 300 % ensure safe operation, also at
the limits.
Surge protection devices
VARITECTOR PU - Class II
power protection for individual
consumers - offers protection
against surge voltages for
supplying industrial production.
For more information see CAT 4.4
10
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
connectPower PROmax switched-mode power supply unit
PROmax power to outperform
Offers flexible solutions for ambitious automation
Powerful supply for machines and systems
•• Single and two/three phase models
•• 5V, 12V, 24V, 48 V models
•• High power reserves up to 60°C and a start-up at -40°C for
safe operation
•• Robust thanks to an input voltage range of up to 277 V
AC, surge protection category III and SEMI F47
•• Side-by-side connectability and a very thin design to save
space in the cabinet
•• International approvals guarantee an international use
SEMIF47
u (EMC1)
Cl. I Div. 2
General technical data
Derating curves
Current limiting
> 120 % IN
Insulation voltage input earth
Insulation voltage output earth
Insulation voltage input/output
Earth leakage current
Series switching capability
Ambient temp. operating
Storage temperature
Start up
Humidity at operating temperature
Class of protection
Pollution degree
MTBF
Housing version
3.5 kV
0.5 kV
4 kV
3.5 mA
Yes
-25 °C...+70 °C (derating @ 60 °C)
-40 °C...+85 °C
≥ -40 °C
5...95 %, no condensation
1
2
>500,000h (25°C, IEC 61709)
Metal, corrosion resistant
Status indication
LED red/green and relay (≥21.6 V DC LED green,
relay on/ ≤20.6 LED red, relay off)
Mounting position, installation notice
Horizontal on TS35 mounting rail, with 50 mm of
clearance at top and bottom for air circulation. Can
be mounted side by side with no space in between.
EMC / shock / vibration
Noise immunity tests acc. to
EN55024; EN55022; IEC61000-3-2,-3;
IEC61000-4-2,-3,-4,-5,-6,-8,-11
Resistance against vibration and shock
2.3 g / 30 g in all directions
Electrical safety (applied standards)
Electrical equipment of machines
Acc. to EN60204
Safety transformers for switched-mode
power units
Acc. to EN61558-2-16
Machinery with electronic equipment
Acc. to EN50178 / VDE0160
Safety extra-low voltage
SELV acc. to EN60950,
PELV acc. to EN60204, IEC61204
Protective separation
Protection against electrical shock
VDE0100-410
Acc. to DIN57100-410
Protection against dangerous
shock currents
Acc. to VDE0106-101
Note: Adjustable output voltage -
5V: 4.5...7V, 12V: 10...15V, 24V: 22.5...29.5V,
48V: 30...56V
Max. limiting average on state current [A]
/RDG
Technical data
7HPSƒ&
Typ\Temp. 45°C
1ph 24V/3A 3.6
1ph 24V/5A
6
1ph 24V/7.5A 9
1ph 24V/10A 12
1ph 24V/20A 24
1ph 24V/40A 48
1ph 5V/14A 16.8
1ph 12V/6A 7.2
1ph 12V/10A 12
1ph 48V/5A
6
1ph 48V/10A 12
1ph 48V/20A 24
3ph 24V/5A
6
3ph 24V/10A 12
3ph 24V/20A 24
3ph 24V/40A 48
50°C
3.3
5.7
8.5
11.3
22.6
45.2
15.8
6.8
11.3
5.7
11.3
22.6
5.7
11.3
22.6
45.2
55°C
3.2
5.4
8
10.7
21.4
42.8
15
6.4
10.7
5.4
10.7
21.4
5.4
10.7
21.4
42.8
65°C
2.6
4.4
6.6
8.8
17.6
35.2
12.3
5.3
8.8
4.4
8.8
17.6
4.4
8.8
17.6
35.2
70°C
2.2
3.8
5.6
7.5
15
30
10.5
4.5
7.5
3.8
7.5
15
3.8
7.5
15
30
PROmax
Ordering Data
Single-phase
N. Voltage N. Current
PRO MAX 72W
24V
3A
PRO MAX 120W 24V
5A
PRO MAX 180W 24V
7.5A
PRO MAX 240W 24V
10A
PRO MAX 480W 24V
20A
PRO MAX 960W 24V
40A
PRO MAX 70W
5V
14A
PRO MAX 72W
12V
6A
PRO MAX 120W 12V
10A
PRO MAX 240W 48V
5A
PRO MAX 480W 48V
10A
PRO MAX 960W 48V
20A
2/3-phase
PRO MAX3 120W 24V
5A
PRO MAX3 240W 24V
10A
PRO MAX3 480W 24V
20A
PRO MAX3 960W 24V
40A
Diode module 24V only
CP M DM20
2 x 10 A
CP M DM40
2 x 20 A / 1 x 40 A
*N. = Nominal
60°C
3
5
7,5
10
20
40
14
6
10
5
10
20
5
10
20
40
H x W x D/ Weight
130/32/125 mm/ 0.6 kg
130/40/125 mm/ 0.8 kg
130/50/125 mm/ 0.9 kg
130/60/125 mm/ 1 kg
130/90/150 mm/ 2.0 kg
130/140/150 mm/ 3.4 kg
130/32/125 mm/ 0.6 kg
130/32/125 mm/ 0.6 kg
130/40/125 mm/ 0.8 kg
130/60/125 mm/ 1 kg
130/90/150 mm/ 2.0 kg
130/140/150 mm/ 3.4 kg
1478100000
1478110000
1478120000
1478130000
1478140000
1478150000
1478210000
1478220000
1478230000
1478240000
1478250000
1478270000
130/40/125 mm/ 0.65 kg
130/60/125 mm/ 1.3 kg
130/70/150 mm/ 1.3 kg
130/140/150 mm/ 3.1 kg
1478170000
1478180000
1478190000
1478200000
130/34/150 mm/ 0.3 kg
130/60/150 mm/ 0.6 kg
1222210000
1222220000
11
DC-UPS uninterruptible power supply
DC-UPS uninterruptible power supply
Safe energy in automation
Can be used around the world
International approvals (cURus, cULus) and TÜV
certification facilitate the use of these products
around the world, and in different applications.
Space saving
The ability to mount the UPS components
side-by-side in only 66 mm width saves
space in the electronics cabinet.
Quick error analysis
The charging level indicator and the
status and error indicators facilitate
rapid error analysis.
{\
Long battery service life
The temperature-compensated characteristic charge
curve ensures the best charge for the battery.
This maintains the battery‘s long service life.
Flexible application
Multiple operation modes optimise
the use of battery power and
facilitate its flexible application.
Time saving
The three additional active 24 V DC
transistor outputs simplify cabling
and save time.
Create your own, individual
power supply solution
Buffers short duration
You can reliably bridge short power
interruptions of several 100 ms with the
maintenance-free buffer module.
Versatile battery modules
of 1.3 to 17 Ah
The battery modules are equipped with
maintenance-free AGM VRLA batteries. An
integrated temperature sensor ensures the
constant, accurate charging of the battery.
The PROmax power supply units
with diverse add-on modules
meet nearly every requirement for
durable power supplies.
12
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
DC-UPS uninterruptible power supply
Uninterruptible power supplies
DC-UPS 10/20A or 40A
Backup power supplies
•• Hold up time of 40A for 30mins or 1A for 30 hours
•• Extended battery life with temperature controlled charging
•• 1 digital input for Interlock
•• 3 relay outputs +3 digital—Fault, Buffering, Charging
•• LED indication of status
•• Hold up times from 0.5 to 45 mins - ∞
•• -25 to +70°C operation
•• 1.3, 3.4, 7.2, 12, and 17Ah Battery modules
•• NEW Battery test button
\
Technical data
Indication
Electrical safety (applied standards)
Status relay ( max.load 30 V AC/DC 0.1 A)
Fault (alarm), battery operation (buff.), charging
(charg.)
Transistor outputs (24 to 27 V DC max.
load 150 mA)
Fault (alarm), battery operation (buff.), charging
(charg.)
LED status indicator
Three-colour LED: battery capacities
> 85 % green, > 40 % yellow, > 20 % red,
< 20 % red (flashing)
Green/yellow LED: normal / buffering
Yellow/red LED: temperature alarm / alarm
Yellow/red LED: switch-off / battery fault
General technical data
Ambient temperature (operational)
–25 °C…+70 °C
Storage temperature
Max. perm. air humidity
Protection degree
Class of protection
Pollution severity level
Overvoltage category
–40 °C…+85 °C
5…95 %
IP 20
3
2
III
Insulation voltage input/output to housing/
ground
1300 V DC 1 min (typetest)
MTBF
> 500,000 hours acc. to IEC 1709
Protection against reverse voltages from
the load
32…34 V DC
Parallel connection option
Housing version
Yes, only with diode module for redundancy
Metal, corrosion resistant
Mounting position, installation notice
Horizontal on mounting rail TS 35,
50 mm above and below
Space for free movement of air
Overload protection
Yes
Short-circuit protection
Yes
EMC / shock / vibration
Interference emission
Interference immunity tests
Acc. to EN55022 Class B
Acc.to EN61000-4-2 (ESD), EN61000-4-3 and
EN61000-4-8 (fields),
EN61000-4-4 (burst), EN61000-4-5 (surge),
EN610004-6 (conducted),
EN61000-4-11 (dips)
Resistance against vibration and shock
Acc.to IEC60954 Vibration: 2.3 g,
Acc.to IEC60068-2-31 shock: 30 g in all
directions
Acc. to EN60204
Safety transformers for switch-mode power
supplies
Acc. to EN61558-2-17
Machinery with electronic equipment
Acc. to EN50178 / VDE0160
Extra-low voltage protection
SELV acc. to EN60950, PLEV acc. to EN60204
Battery supply time
UPS control unit
Ordering Data - UPS
Type
CP DC UPS
CP DC UPS
*N. = Nominal
N. Voltage N. Current
24V
20A/10A
24V
40A
H x W x D/ Weight
130/66/150 mm/ 1 kg
130/66/150 mm/ 1 kg
Buffer Time
1.3Ah
3.4Ah
7.2Ah
12Ah
17Ah
10A
20A
40A
11.3min
5min
-
11.3min
5min
-
26.5min
11.5min
5min
51min
22.7min
9min
81min
34min
13.5min
MAX O/P current
15A
25A
50A
50A
50A
* Table shows approximate time (when fully charged) based on current.
If unsure select 1 battery size higher.
Type
CP A BATTERY
CP A BATTERY
CP A BATTERY
CP A BATTERY
CP A BATTERY
*N. = Nominal
N. Voltage
24V DC
24V DC
24V DC
24V DC
24V DC
1370050010
1370040010
Battery modules
Ordering Data - Batteries
Battery modules data details
Battery Size
Electrical equipment of machines
N. Current
1.3 Ah
3.4 Ah
7.2 Ah
12 Ah
17 Ah
H x W x D/ Weight
148/52/124 mm/ 1.5 kg
144/108/137 mm/ 3.6 kg
155/162/134 mm/ 5.9 kg
155/229/134 mm/ 9.2 kg
178/242/160 mm/ 13.3 kg
1406930000
1251070000
1251080000
1251090000
1251110000
13
Uninterruptible power supply - DC Buffer modules
DC Buffer Module
Your 24 V DC supply saviour
The perfect backup solution
Buffer units use capacitor base storage instead of batteries to
over-ride short dips in the 24V DC power supply to provide a
smooth and continuous supply for 260ms at 20A, or 1A for
6 seconds. Buffer units are simply installed in series between
the 24V DC supply and the load and are maintenance free
with a MTBF greater than 57 years, providing 2 outputs for
feedback of ready and fault plus LED indication.
•• Maintenance Free
•• Parallel units to increase time
•• Output notification for OK and Fail
•• LED status indication
•• Operating temperature range: -25 ˚C...70 ˚C
Technical data
Input
DC Buffer Module
Ordering Data
Dimensions
150/66/130
1.15kg
Input voltage
24V DC (22.5...30V DC)
Input current
Max. input current
0...22A
22A
Weight
Input protection
Transient surge protection,
35V DC suppressor diode
Type
Output
24V DC
Output voltage adjustable range
Output current
22.5...30 V DC
20A, Max.22A
Parallel connection option
Yes, to increase buffer time,
without diode module
Series connection option
Overload protection (Discharging process)
Over voltage protection (Discharging process)
Fail - Relay
NO
≥ 22A
31...34 V
30V AC/DC 2A
Ready - Active Digital
24V DC, 300mA voltage
Indication
Ready
General data
Length x Width x Height mm
Ordering data
Output voltage
CP DC BUFFER 24V 20A
1251220000
non-safe load
Green LED
95%
Memory medium
Charging time
Buffering time
Internal, capacitor
25S
200˜ 300ms at 20A 6S at 1A
MTBF
>100.000h acc. MIL-HDBK 217(Bellcore);
>500.000h acc. IEC 1709(SN29500)
Ambinent temperature
- 25 ˚C...+70 ˚C (mounted without clearance
between units)
Storage temperature
-40...+85 ˚C
Clamping mm2 (norminal/min./max.)
Order No.
Block diagram
Efficiency
Screw connection data
\
%
Input
10/0.3/16
Output
10/0.3/16
Safe Load
Signal
Line
Buffer time
4/0.13/6
7
[S]
Buffering Time
6
5
4
3
2
1
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
[A]
24 V DC
14
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
connectPower DC/DC converter
DC/DC converter
Stablise and isolate 24V DC supply
Isolate and regulate your DC supply
The 10A, 24V/24V DC-DC converter is designed to isolate
and regulate 24V DC supplies distributed from other sources.
With a voltage range of 18-31V DC input/ 22.5...29.5V
output, can be used in Ship building, Process or Automation
applications. The DC/DC converter can eliminate ground
loops on long 24V DC runs, be used in floating ground
systems, or regulate supply from a 24V DC battery system.
•• Wide ranging input
•• Adjustable output voltage
•• Integrated fault alarm
•• Wide operating temperature
General technical specifications
Ordering Data
Output characteristic curve / current limit
IU / > 120 % IR
Earth discharge current
Ambient temp. Operating / storage temp.
Max. permitted humidity (operational)
Protection degree
Class of protection
Contamination degree
< 0.005 mA
–25 °C … +70 °C / –40 °C … +85 °C
5 %…95 % RH
IP 20
III
2
Insulation voltage
2.5 kV AC 1 min. / 1.5 kV AC 1 min. / 0.5 kV
AC 1 min.
Overvoltage category
III
MTBF
> 500,000 hrs. according to IEC 1709
(SN29500)
Protection against load reverse voltages
Parallel capability (without diode module)
Mountable side-by-side without gaps
Housing version, metal
Signal operations
Mounting position, installation notice
33…34 V DC
Yes, max. 5
Yes
Resistant to corrosion
LED green / red
Horizontal on TS 35 DIN rail, above and below
50 mm
Clearance for air circulation, suitable for aligning
without clearance gap
For installation in rotating systems
Yes
Metal clip-on foot
EMC / shock / vibration
Noise emission according to EN55022
Interference immunity tests, according to
Limiting of mains voltage harmonic currents
Resistance against vibration and shock
Electrical safety (applied standards)
150 / 60 / 130 mm
1250 g
Length x Width x Height mm
Weight
Ordering data
CP DCDC 250W 24V 10A
1313320010
Type
Order No.
Accessories
Type
CP A WALL ADAPTER 45MM
SDIS 0.5X3.0X100
SDIS 1.0X5.5X125
Order No.
1461850000
9008380000
9008410000
Description
Wall mount bracket
Small screwdriver
Large screwdriver
Derating curves
Connection diagram
PE N
+
L
Load
Temperature derating
130
–
120
Charger
110
100
90
80
70
60
Class B
EN61000-4-2 (ESD), EN61000-4-3 and
EN61000-4-8 (Fields),
EN61000-4-4 (Burst), EN61000-4-5 (Surge),
EN610004-6 (conducted),
EN61000-4-11 (Dips)
According to EN 61000-3-2
DC/DC converter
Dimensions
Pout [% Pn]
Technical data
\u
%
20
30
40
50
60
70
80
Battery bank
Ambient temperature [°C]
–
+
According to EN50178, shock: 5 g in all
directions
Electrical equipment of machines
According to EN60204
Safety transformers for switched-mode
power units
According to EN61558-2-17
Machinery with electronic equipment
According to EN50178 / VDE0160
Safety extra-low voltage
SELV according to EN60950,
PLEV according to EN60204
Protective separation
Protection against electrical shock
VDE0100-410
According to DIN57100-410
Protection against dangerous shock currents
According to VDE0106-101
15
connectPower PRO-H
PRO-H power supply
Industrial power supplies for extreme requirements
Shock & vibration proof
Designed for use in areas of high shock and vibration.
Status Alarms
Green LED OK
Red LED OFF
Remote alarms
16
Reliable
Equiped for long reliable service life. High
Mean Time Between Failures (MTBF) up to
1.8 Million hours.
Robust
Wide temperature range from –25 °C to +70 °C.
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
connectPower PRO-H
PRO-H power supply
High performance power supplies
For extreme requirements
The PRO-H is a new generation of high performance DIN-rail
mounted single and two phase wide voltage power supplies
designed to provide extended service life in Process and
Machinery applications where reliability is paramount. The
SNT2 models provide continuous output with supply inputs
from 100-500VAC, providing a truly universal supply for any
electrical power system. The PRO-H Redundancy modules are
active modules that communicate with PRO-H power supplies
to provide 100% current sharing ensuring your redundancy
provides the best performance.
% { \ | CB
Scheme
•• MTBF >100 years
•• Output OK signalling
•• Wide operating voltage
•• Active redundancy modules
•• Remote input for output on/off
General technical data
Derating curves
Ambient temp. operating / storage temp.
Max. perm. air humidity (operation)
Degree of protection / Class of protection
Insulation voltage input/output
-25…+70 °C / -25 °C…+85 °C
95 % RH
IP 20 / I, with PE connection
4 kV I/O, 2 kV I/earth, 0.5 kV O/earth
MTBF according to IEC 61709
CP T … 70/90 W
> 1.8 Mio. h
CP T … 140 W
> 1.2 Mio. h
CP T … 180/360/600 W > 0.9 Mio. h
Protection against reverse voltages from
the load
16 V DC / 35 V DC / 63 V DC
Parallel connection option
Housing version
Overload protection
Short circuit protection
Yes, without diode module
Metal, corrosion resistant
Thermal protection, automatic restart
Unlimited, automatic restart
Mounting position, installation notice
Horizontal on TS 35 mounting rail, with 80 mm
space at top and bottom.
Side by side mounting with 50 mm clearance.
Stripping length (rated connection)
7 mm
Signal indication
Power Good Signal
Max. limiting average on state current [A]
CP T SNT...
100
90
Output Power [% Pmax]
Technical data
600 W
80
70
90 W
180 W
360 W
60
50
40
-25
40
50
70 W
140 W
60
Potential free, floating signal contact
NO contact: 30 V DC / 1.0 A max. for 12/24 V
DC modules
NO contact: 48 V DC/ 0.5 A max. for 36/48 V
DC modules
Active output signal
70 W: 11 V DC ± 1 V DC / 20 mA max.
140 W: 11 V DC ± 1 V DC / 40 mA max.
90 W: 22 V DC ± 2 V DC / 10 mA max.
180/360/600 W 24 V DC, 22 V DC± 2 V DC /
20 mA max.
180/360/600 W 48 V DC, 44 V DC± 4 V DC /
15 mA max.
50°C
5.7
9.5
3.1
6.3
12.5
22.5
15.0
1.6
3.3
6.3
11.3
6.3
12.5
22.5
60°C
5.4
7.0
2.5
5.0
10.0
20.0
13.3
1.3
2.5
5.0
10.0
5.0
10.0
20.0
70°C
4.5
3.7
1.7
3.3
6.7
13.3
9.0
0.8
1.7
3.3
7.5
3.3
6.7
13.3
Ordering Data
Type CP T SNT
Trigger point: 12 V Version 9…11 V DC
Trigger point: 24 V Version 18...22 V DC
Trigger point: 48 V Version 36...44 V DC
70
Temperature [°C]
Typ\Temp.
40°C
1 ph 12V/6A
6.0
1 ph 12V/12A
12.0
1 ph 24V/3.8A
3.8
1 ph 24V/7.5A
7.5
1 ph 24V/15A
15.0
1 ph 24V/25A
25.0
1 ph 36V/16.5A 16.5
1 ph 48V/2A
2.0
1 ph 48V/4A
4.0
1 ph 48V/7.5A
7.5
1 ph 48V/12.5A 12.5
1-2 ph 24V/7.5A 7.5
1-2 ph 24V/15A 15.0
1-2 ph 24V/25A 25.0
Output voltage Output current
CP T SNT 70W 12V 6A
12V DC
6.5 A
CP T SNT 140W 12V 12A
CP T SNT 90W 24V 3.8A
CP T SNT 180W 24V 7.5A
CP T SNT 360W 24V 15A
CP T SNT 600W 24V 25A
CP T SNT 180W 48V 4A
CP T SNT 360W 48V 7.5A
12V DC
24V DC
24V DC
24V DC
24V DC
48V DC
48V DC
13.0 A
3.75 A
7.5 A
15 A
25 A
4A
7.5 A
CP T SNT 600W 48V 12.5A
48V DC
12.5 A
CP T SNT2 180 W 24 V 7.5 A
24V DC
7.5 A
CP T SNT2 360 W 24 V 15 A
24V DC
15 A
CP T SNT2 600 W 24 V 25 A
24V DC
25 A
CP T RM 10
24V DC
15A @ 24V DC @ 40°C
CP T RM 20
24V DC
25A @ 24V DC @ 40°C
Type CP T SNT2
PRO-H diode modules
Order No.
1105430000
1105440000
1105790000
1105810000
1105820000
1105840000
1105850000
1105860000
1105870000
1194480000
1194490000
1194310000
1105880000
1105890000
17
PRO-E power supply
NEW
PRO-E power supply
Plate-mounted single-phase power supply for
autonomous applications
Safe operation
Overload protection, short-circuit protection,
surge protection and reverse polarity protection
guarantee stable operation.
Has a wide range of uses
Wide range input voltage of
85–264 V AC and 110–370 V DC.
18
Robust
Wide operating temperature range
from – 25°C to 70°C
(derating from 50°C, 70 % at 70°C).
Can be used around the world
All-purpose usage due to worldwide
approvals CE, UL, TÜV, CCC.
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
PRO-E power supply
PRO-E power supply
Plate-mounted power supplies
For industrial automation
Our new plate-mounted PRO-E power supplies offer an
excellent price/performance ratio and are designed for
all-purpose use. Thanks to the wide variety of models with
output voltages of 5 V, 12 V, 24 V and 48 V, as well as
extensive international approvals, it is suitable for use in many
applications. The performance bandwidth ranges from 25 W
up to 350 W. Individual adaptability makes PRO-E the right
choice for your power supply
% { \ | CB
•• Stable DC output voltage
•• Wide AC and DC input voltage range
•• Adjustable output voltage
•• Wide operating temperature range: -25 ˚C...70 ˚C
•• Worldwide approvals: CE, UL, TÜV, CCC, CB
•• Robust and stable housing
Scheme
Dimensions
Technical data
Input
Input voltage
85–264 VAC, 110–370 VDC
Input frequency
47–63 Hz
Output
Output voltage
5 VDC
Output voltage adjustment
±10 % of the rated output voltage
(with potentiometer)
12 VDC
24 VDC
Rated output power
25W, 50W, 75W, 100W, 150W, 250W, 350W
Overload protection
120~150 % Iconst. of the rated output current,
automatic restart
Over voltage protection, YES
5.6~6.8 V 13.5~16.2V 28~32 V
Hold-up time
≥20 ms
Control at 10…100 % load (load regulation) 0.5 % - 350W ≤ 2%
Parallel connection option
Isolation to enclosure
48 VDC
55~62 V
0.5 kVAC
Isolation input – earth
1.5 kVAC
Isolation input – output
CP E SNT 25W 5V 5A
3 kVAC
General data
Operating temperature
–20 °C to 70 °C (>50 °C derating, see diagram);
70% @ 70 °C
Storage temperature
Humidity during storage
Efficiency, 76 ... 87 %
Status indicator
Standards
–20 °C to +85 °C
5~95 %
77 %
79 %
green LED
EN 60950
Electromagnetic compatibility
EN 55011, EN 55022, EN 55024,
EN 61000-6-2, 3
Fixing
Weight
wall mounting, screwable
0.24 kg - 1025 kg
Approvals and marks
CE, cURus, TÜV, CCC, CB
Screw connection
Wire cross-section
mm² 0.34~4
84 %
83 %
Dimensions H x W x D mm
28 x 51 x 91 mm
35 x 100 x 105 mm
40 x 98.5 x 135 mm
40 x 97.5 x 164 mm
40 x 99 x 205 mm
230 x 115 x 49.5 mm
230 x 115 x 49.5 mm
Ordering Data
Type
with diode module
Isolation output – earth
Type
CP E SNT 25W
CP E SNT 50W
CP E SNT 75W
CP E SNT 100W
CP E SNT 150W
CP E SNT 250W
CP E SNT 350W
Output voltage Output current Output power
5V
5A
25 W
CP E SNT 25W 12V 2.1A
CP E SNT 25W 24V 1.1A
CP E SNT 25W 48V 0.57A
CP E SNT 50W 5V 10A
CP E SNT 50W 12V 4.2A
CP E SNT 50W 24V 2.2A
CP E SNT 50W 48V 1.1A
CP E SNT 75W 5V 12A
CP E SNT 75W 12V 6A
CP E SNT 75W 24V 3.2A
CP E SNT 75W 48V 1.6A
CP E SNT 100W 5V 16A
CP E SNT 100W 12V 8.5A
CP E SNT 100W 24V 4.5A
CP E SNT 100W 48V 2.3A
CP E SNT 150W 12V 12.5A
CP E SNT 150W 24V 6.5A
CP E SNT 150W 48V 3.3A
CP E SNT 250W 12V 21A
CP E SNT 250W 24V 10.5A
CP E SNT 250W 48V 5.2A
CP E SNT 350W 24V 14.6A
12V
24V
48V
5V
12V
24V
48V
5V
12V
24V
48V
5V
12V
24V
48V
12V
24V
48V
12V
24V
48V
24V
2.1A
1.1A
0.57A
10A
4.2A
2.2A
1.1A
12A
6A
3.2A
1.6A
16A
8.5A
4.5A
2.3A
12.5A
6.5A
3.3A
21A
10.5A
5.2A
14.6A
25 W
25 W
25 W
50W
50W
50W
50W
75W
75W
75W
75W
100W
100W
100W
100W
150W
150W
150W
250W
250W
250W
350W
CP E SNT 350W 48V 7.3A
48V
7.3A
350W
Order No.
1202640000
1202630000
1202620000
1202610000
1202590000
1202580000
1202450000
1202460000
1202470000
1202480000
1202490000
1202510000
1165820000
1165830000
1165840000
1165850000
1165870000
1165880000
1165890000
1202520000
1202530000
1202540000
1202550000
1202560000
19
connectPower INSTAPOWER
INSTAPOWER
Single phase 25-48W
Adjustable output versatility
The INSTAPOWER single phase 25-48W power supplies
provide the answer to a wide range of power supply needs.
Just four different modules provide for all output voltages
from 4 to 55V DC. An easily accessible trimpot is provided
via an access port to enable wide adjustment to meet your
requirements. Fully protected against overload, INSTAPOWER
48W provides up to 50% over current to start your load.
•• Wide range of adjustment & universal AC/DC inputs
•• Suitable for use as a DC/DC Converter
•• Ultra-compact only 70mm wide
•• Mounts on standard TS35 DIN rail
%
\
Technical data
Type
CP SNT 25W 5V 5A
4-8V DC
Output voltage
Output current
Input voltage
CP SNT 48W 12V 4A
CP SNT 48W 24V 2A
9-15V DC
15-28V DC
4A
2A
85-264V AC / 110-370V DC
85-264V AC / 110-370V DC
CP SNT 48W 48V 1A
46-55V DC
1A
85-264V AC / 110-370V DC
5A
85-264V AC / 110-370V DC
Order No.
8754960000
8754970000
8739140000
8879230000
INSTAPOWER
Single phase 24W
For driving inductive loads
Devices such as relays, contactors, solenoids and motors
all require an initial starting current many times their
normal level. The compact INSTAPOWER range has the
capacity to supply the initial inrush current to start inductive
loads and can actually provide 3 times their rated output for
a short duration.
•• Thermal overload protection & automatic restart
•• High Efficiency & universal inputs
•• Compact design only 52mm wide
•• Mounts on standard TS35 DIN rail
•• Suitable for use as a DC/DC converter
%
\
Technical data
Type
20
CP SNT 24W 5V 2A
5V DC
Output voltage
Output current
Input voltage
CP SNT 24W 12V 1.5A
CP SNT 24W 15V 1.5A
CP SNT 24W 24V 1A
12V DC
15V DC
24V DC
1.5 A
1.5 A
1A
85-265V AC / 120-300V DC
85-265V AC / 120-300V DC
85-265V AC / 120-300V DC
CP SNT 24W 28V 1A
28V DC
1A
85-265V AC / 120-300V DC
2A
85-265V AC / 120-300V DC
Order No.
9928890005
9928890012
9928890015
9928890024
9928890028
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
Fuse protection
WAVEGUARD
24V DC Electronic fuse protection
•• Front panel on/off switch
•• Local or remote reset
•• LED status indication
Technical data
Type
Unom [V]
IOUT [A]
WGS 24 V dc 1.6 A
24
1.6
WGS 24 V dc 3.15 A
WGS 24 V dc 6.3 A
WGS 24 V dc 8.0 A
24
24
24
3.15
6.3
8.0
WGS 24 V dc 0.5–5 A
24
0.5–5 adjustable
Order No.
8618890000
8618910000
8618930000
8618940000
8710270000
\
%
Fuse Terminals
Overload and short-circuit protection
ZSI
28 V DC
WSI 6
Metric fuses
WSI 6 LD
Metric fuses / bipolar LED
ETA 1170
Ordering data
Type
ZSI 2x6/4x2.5 FC
Qty.
10
Order No.
1058520000
*Note: Suitable for auto fuse or circuit breaker
Accessories
Circuit breaker 1170
3
4
5
6
7.5
8
10
15
20
25
Colour
violet
pink
orange
green
brown
yellow
red
blue
yellow
white
Ordering data
Type
WSI 6
Qty.
50
Order No.
1011000000
*Note: Suitable for auto fuse or circuit breaker
Order No.
1278730000
1278740000
1278750000
1278760000
1278770000
1278780000
1278790000
1278810000
1278820000
1278830000
Accessories for WSI 6 / LD
Screwable
cross-connection
2-pole
3-pole
4-pole
10-pole
G-fuse cartridge,
5 x 20 mm
0.10 A fast
0.20 A fast
0.25 A fast
0.50 A fast
Type
Current
Order No.
QL 2 SAK6N
QL 3 SAK6N
QL 4 SAK6N
QL 10 SAK6N
Type
32 A
57 A
57 A
32 A
Voltage
0194300000
0194400000
0194500000
0338300000
Order No.
G 20/0.10 A/F
G 20/0.20 A/F
G 20/0.25A/F
G 20/0.50A/F
250 V
250 V
250 V
250 V
0430300000
0430400000
0430500000
0430600000
Ordering data
Type
Description
WSI 6/LD 10-36V DC/AC 10-36V AC/DC
WSI 6/LD 30-70V DC/AC 30-70V AC/DC
WSI 6/LD 60-150V DC/AC 60-150V AC/DC
WSI 6/LD 250AC
140-250V AC/DC
*Note: Suitable for auto fuse or circuit breaker
Accessories for WSI 6 / LD
G-fuse cartridge,
5 x 20 mm
0.63 A fast
1.00 A fast
1.60 A fast
2.00 A fast
2.50 A fast
3.15 A fast
4.00 A fast
5.00 A fast
6.30 A fast
Order No.
1011300000
1012200000
1012300000
1012400000
Type
Voltage
Order No.
G 20/0.63 A/F
G 20/1.00A/F
G 20/1.60 A/F
G 20/2.00A/F
G 20/2.50 A/F
G 20/3.15 A/F
G 20/4.00 A/F
G 20/5.00 A/F
G 20/6.30 A/F
250 V
250 V
250 V
250 V
250 V
250 V
250 V
250 V
250 V
0439000000
0430700000
0430800000
0430900000
0431000000
0431100000
0431200000
0431300000
0431400000
21
Technical overview
Application specific requirements
Weidmüller – power supply solutions for all applications
Parallel operation
+
DC-DC conversion
Load
DC UPS
–
PE
N
+
L
Load
+
24 V DC
24 V DC
+–
–
–
Charger
Battery bank
–
+
L
N
PE
Alarm Status
Increasing the output power
Galvanic isolation and stabilisation
Uninterruptible power supply
The direct parallel circuit consisting
of several power supplies enables
customised adaptation of the output
power. This must not be confused
with redundant switching, when the
stabilised load current is to be shared
equally.
DC/DC converters galvanically isolate
the input from the output voltage and
prepare them:
Mains interruptions and brown-outs are
a frequent cause of system failures.
Battery-supported or capacitor based
uninterruptible power supply units
(UPS) units cover these types of mains
network faults and thereby increase
system availability.
•• PROeco, PROmax and PRO-H power
supply units: up to five devices can
be connected in parallel.
•• Also featuring our INSTAPOWER
power supplies: up to three devices
can be directly switched in parallel.
•• Indication of the failure of individual
devices can be achieved using
optional diode modules.
•• To compensate for voltage losses
which occur due to the higher cable
resistance,
•• To avoid ground loops which can
occur in plants which are spread
over a large area.
•• A potential-free alarm relay and a
transistor output give you full status
monitoring.
•• The DC/DC-Converter is a protection
class III device, thus you can use
them in floating earth systems such
as might be found when operating
back-up batteries.
Useful information
To ensure the most even
distribution of the load within the
parallel connected power supply
units, the voltage difference
must not be more than ±50
mV. This balance is achieved
when the plus wire is connected.
Symmetrical wiring also helps
to distribute the current uniformly.
22
Charging Status
Buffering Status
Antenna
Solar Cell
Antenna
•• Different status relays permit status
monitoring.
•• The UPS control unit monitors the
input voltage and, in the event of
a fault, switches immediately to
battery operation.
•• When the power is restored, the
input voltage is again switched
over to the load and the battery is
recharged.
•• An integrated deep-discharge
protection system and an optimised
charge curve ensure that the battery
has a long service life.
24VDC
I/O Devices
and Sensors
I/O 24VDC
24VDC
Radio
Transmitter
24V (powered)
SCADA System
or Other Type
of Control System
24VDC
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
Technical overview
CAP module
Redundancy
+
Load
Electronic fusing
+
–
Load
–
Load 1
+
Load 2
Load 3
Load 4
–
Alarm
A
L1
L2
L3
PE
Status relay
24 V
+
Load
–
A
B
B
Status relay
24 V
L1
L2
L3
PE
Reset
L N PE
Power reserve for peak currents
Redundant power supply units
Selective load protection
For selective triggering of circuit
breakers or for short-term additional
power reserves, a capacitor module
can be integrated into the 24 V circuit.
The availability of the power supply
units is increased by the use of
redundant circuits. Here, each
individual power supply unit can cope
with the total load required in the event
of a failure by itself.
The breakdown of the whole secondary
load into individual load circuits which
have quick-operating safety elements in
case of a fault is known as selective
load protection. Electronic fuses are
ideal to meet the special requirements
found in selective load protection.
•• The integrated alarm relay monitors
the input voltage, thereby monitoring
the status of the 24 V DC power
supply.
•• Sufficient power for the pulse
triggering of circuit breakers (MCBs)
•• To further increase the power
reserves, multiple capacitor modules
can be connected in parallel.
Ordering Data
Type
CP M CAP
U [V]
18-30
I [A] / 1 [ms]
40
Order No.
7760052061
•• In the case of redundancy switching,
the diode module‘s output current
must not exceed that of either
switched-mode power supply units.
•• Diode modules are also used
for a secure parallel circuit of
switched-mode power supply units.
•• Full status monitoring thanks to
integral alarm monitoring the voltage
of both inputs.
Useful information
TIP
The capacitor module can be
used independently of the output
power from the power supply
modules. When triggering circuit
breakers, the line impedance
must be observed. You will find
the relevant values for circuit
breakers here:
www.weidmueller.com/MCB
An example of redundant power
supply units
•• The tripping characteristic curve of
the electronic fuse is, on the one
hand, fast enough to switch off the
faulty circuit quickly; and on the
other, tolerant enough to deal with a
motor start-up or capacitive loads.
•• A switch to turn the output on or off
means that it is simpler to diagnose
errors and to commission.
•• The fuse triggering is signalled via a
potential-free alarm relay
•• A reset input allows the fuse to be
switched on again remotely.
for an output current of 20A:
2 x PRO-M, 20A + 1x CP M DM20
for 40A output load:
2 x PRO-M, 40A + 2x CP M DM40
23
Technical overview
Active redundancy
24 V
PRO-M
24 V
–
100% Load
50% Load
Pout [% PN]
50% Load
24 V
PRO-M
24 V
M
M
130
120 Additional
Power
110 Reserve
up
to 45°C
100
90
80
70
60
t
3 ms
Temperature derating Temperature derating
130
Pout [% PN]
+
L
N
PE
20
30
40
120 Additional
Power
110 Reserve
up
to 45°C
100
90
Δ –2.5 %
U [V]
U out
U out
Δ –2.5 %
80
Power
Power
70
Reserve
Reserve
60
20 50
30 60
40 70
50 80
60
Ambient temperature [°C]
Ambient temperature [°C]
70
80
IN
I Reserve
IN
I [A]
I Reserve
t
PRO-M Output Power Derating Curve
U/I output characteristic with power reserve
Active load distribution
Operating temperature, power
reserve and derating
Short-circuit and overload
Active load distribution (active current
sharing) ensures that a load current is
evenly shared over two power supplies.
The availability of the total power
supply is increased considerably, as
each power supply is always operated
with just half of the nominal load at
most.
Power supply units for industrial use
offer extended operating temperature
ranges (–25 to +70 °C). Up to the
“derating” operating point, they have
power reserves, above this point they
can only be operated at reduced load.
The PROmax power supply units follow
the IU output characteristic curve in the
event of a short-circuit/overload and are
therefore permanently short-circuit proof.
Useful information
Only use devices of the same
type at all times. Active load
distribution is guaranteed by
means of the redundancy
modules CP T RM 10 and CP T
RM 20.
•• Up to 45 °C, the device can
be operated continuously with
maximum of 120 % of rated current.
•• Up to 60 °C is 100% of rated current
available.
•• Compared to Hicc-up or foldback
characteristic curves, operation with
almost any capacitive loads is possible.
•• PROmax power supply units deliver a
constant 120 to 150 % of the nominal
current in short-circuit operation with a
simultaneously reduced voltage.
•• When the short-circuit or the overload
is removed, there is a prompt return to
normal operation.
Inrush current limit
Inrush current limiters improve the
dimensioning of the mains fuses
•• Power supply units from the lower
power classes mainly have a passive
inrush current limiter, e.g. PRO-M 3
A and 5 A models.
•• Power supply units with larger
power classes have an active inrush
current limiter, e.g. all 1-phase PRO-M
modules above 10 A.
24
U [V]
I
Imax
Imax
Without active current limiting
With active current limiting
t
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
I
Power Supply Selection Considerations
Power Supply Selection Considerations
Output Voltage
All Weidmüller Switchmode Power Supplies have a
regulated output voltage, that is the output voltage remains
constant irrespective of input voltage or load current,
provided the supply voltage is within the specified range.
Most models can be powered from DC as well as AC
Environmental
Environmental issues to consider are the ambient
temperature where the power supply is expected to operate.
Note the derating for high ambient temperature use.
Vibration in the area of use must also be considered.
Power Boost
All Weidmüller Switchmode Power Supplies have start up
boost of up to 400%. This allows for non resistive loads to
be started. Inductive loads, i.e. solenoid valves and motors,
have a starting current as high as six times full load current,
while capacitive loads, i.e. some electronic devices and
PLC’s with input filtering capacitors have a start up current
of up to twelve times. Switchmode power supplies have
a built in protection circuit which turns the output off if a
sudden load is introduced which exceeds the rated load of
the power supply.
Method of operation
Primary switchmode power supplies are distinguished by a
high degree of efficiency and also by their compact
dimensions and moderate generation of heat. The mains
voltage is rectified directly. The rectified voltage is then
chopped with a higher frequency than that of the mains
frequency. A transformer (which can be quite small due to
the high switching frequency) converts the voltage with the
switching frequency to the required value.
Short Ciruit Protection
Short circuit protection is also built in so that if there is
a short circuit in the load circuit the power supply will
shutdown until the short circuit is removed, and will auto
start.
Mounting
Mounting types available are “DIN” rail mounting or chassis
/ panel mounting. Wall mount options are also available.
Redundancy
For redundant operation where two identical power supplies
are connected in parallel, for reliability and safety reasons
the use of diode auctioneering modules is necessary. In this
configuration there is no possibility of a back feed from one
power supply to the other and supply failure alarms can
be operated.
Load Sharing
When two or more power supplies are to be connected in
parallel for power sharing the output voltage of the power
supplies must be adjusted to be within 50mV of each other.
To achieve this the voltmeter being used must be accurate
and all test leads must be securely connected when making
the adjustment, not just held or pushed onto the terminals.
The method of wiring must also be done in the correct
configuration so as to avoid different wire lengths when
bridging the power supplies. If possible the use of a single
higher output power supply is a better option than parallel
connect smaller power supplies. It is often difficult to get
more than two parallel connected power supplies to
current share.
The voltage is now rectified and smoothed by a filter. This
regulator control itself is carried out by means of pulse-width
modulation. The on and off times of the chopper
transformers are regulated to ensure that the output voltage
remains stable.
Overload Protection
Overload thermal protection is built in to protect the power
supply if the load applied is in excess of the rated current,
for a period of time. This will shutdown the output until
the power supply cools down, and will need to be reset by
disconnecting and reconnecting the input supply.
25
Glossary
Glossary
AGM
Stands for Absorbed Glass Mat. AGM batteries belong to the
VRLA battery family which has the electrolyte absorbed in a
fiberglass mat separator. A gel cell has the electrolyte mixed
with silica dust to form an immobilized gel. Very thin glass
fibres are woven into a mat to increase surface area enough
to hold sufficient electrolyte on the cells for their lifetime.
Float Charge
Float Charge is the constant voltage that is applied
continuously to a voltaic cell/battery under operation. The
voltage could be held constant for the entire duration of
the battery cell‘s operation held for a particular phase of
charging by the charger. The appropriate float voltage varies
significantly with the chemistry and construction of the
battery, and ambient temperature. With the appropriate
voltage for the battery type and with proper temperature
compensation, a float charger may be kept connected
indefinitely without damaging the battery.
Hold-up time (mains-failure bridging time)
The hold-up time (also known as the mains-failure bridging
time) is the interval from the start of the mains outage to
the point in time when the output voltage can no longer be
maintained at its original level. The hold-up time indicates
how long a mains outage may last before it influences the
output voltage. For DC power supplies, EN 61204 requires a
bridging time of at least 20 ms.
U
UA
hold-up time
Power failure
(cutoff)
t
Inrush current
The inrush current refers to the peak current that occurs
when turning on a consumer load. Switched-mode power
supplies have storage capacitors in the input which can
cause significant current peaks while the mains power
is being switched on. A variety of circuitry solutions can
be used to attenuate these current peaks. In the simplest
solution, an inrush limiter is used. Active switching
can be used in other cases. The peak current specification
indicates which upstream fuse should be used in the circuit.
If a fuse is selected which is too sensitive, it can trigger
when the mains power is switched on.
Interlock
The bridge link across the interlock terminals must be
removed to avoid unintended battery operation during
installation and initial test.
26
IU characteristic curve
The IU characteristic curve is a special output characteristic
curve that protects power supply units from overloads and
short circuits. It offers the best performance with regards
to overload and short circuit capabilities. A current limit
is activated at a specific current level (for example, 110
or 120% on the nominal rating). As the load continues to
increase, the output voltage is reduced according to the
current limit curve until it reaches a level approaching zero
volts. Thus a pulsating mode of operations is avoided for
short-term overloads. Large capacitive loads or motors
are brought back up along the slope of the current-limit
characteristic curve. After a short circuit or overload is
fixed, the IU characteristic curve offers the advantage
of immediately returning to the normal voltage control
mechanism. The full output voltage is then immediately
available. The IU characteristic curve is becoming the
established standard for modern power supplies.
Additional variants are available which pertain to the
peak current capacity and the slope of the current-limit
characteristic curve.
U
UA
INominal I Limit
I
UPS
Uninterruptable Power Supply is a 3 stage device. Input
stage, charger for maintaining batteries, and output
stage. If the input power is reduced or drops, energy is
derived from the charged batteries to deliver power to
the output instantaneously.
VRLA Batteries
Stands for Valve Regulated Lead-Acid Battery. More
commonly known as a sealed lead-acid battery.
These batteries have a pressure relief valve which will
activate when the battery is recharged at high voltage.
VRLA batteries offer several advantages compared with
flooded lead–acid cells. The battery can be mounted in any
position, since the valves only operate on overpressure faults.
Since the battery system is designed to be recombinant
and eliminate the emission of gases on overcharge, room
ventilation requirements are reduced and no acid fume
is emitted during normal operation. The volume of free
electrolyte that could be released on damage to the case
or venting is very small. There is no need (nor possibility) to
check the level of electrolyte or to top up water lost due to
electrolysis, reducing inspection and maintenance.
WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
You have equipped your system with an everlasting supply
We take care of the rest with links
Make your system completely reliable and efficient. Our portfolio helps you do this with coordinated
products from the power supply to simple installation in the cabinet.
Your application requirements don‘t stop at guaranteeing reliable system availability. The upstream
power supply and optimum lightning and surge protection are just as important. Downstream, custom-fit
potential distributors and reliable signal and data transmission are essential if your system is to run
smoothly. Our extensive portfolio caters to every need including simple installation thanks to our
high-quality tools and marker systems.
When it comes to supplying power,
we assist you with a range of practical
products. We offer you convenient and
space-saving cabling options for a huge
variety of cross-sections. The products
in our VARITECTOR family reliably
protect your power distribution and the
downstream devices against lightning
and surge damages.
Our relay modules and solid-state
relays for the digital interface layer
are characterised by reliability and
longevity. They switch and amplify
digital signals in your automation and
are used for galvanic isolation between
5 V, 12 V, 24 V up to 230 V AC/DC.
During planning and installation work,
you benefit from different designs and
a wide variety of variants.
u-remote, the innovative remote I/O
solution in an IP 20 package reliably
combines sensors and actuators with
the control using an extremely wide
range of field bus systems. Benefit from
the modular and compact design, and
shrink the size of your cabinets. Our
Industrial Ethernet devices offer an
extensive communication infrastructure
in your machine network.
Let‘s connect.
Find out more about the products and services we offer to guarantee
a permanent supply for your automation, please see website or
Electronics Main Line Australian and New Zealand 2014-2015
We cannot guarantee that there are no mistakes in the
publications or software provided by us to the customer for the
purpose of making orders. We try our best to quickly correct
errors in our printed media.
All orders are based on our general terms of delivery, which can
be reviewed on the websites of our group companies where you
place your order. On demand we can also send the general terms
of delivery to you.
27
Weidmüller – Partner in Industrial Connectivity.
As experienced experts we support our customers and partners around the world
with products, solutions and services in the industrial environment of power,
signal and data. We are at home in their industries and markets and know the
technological challenges of tomorrow. We are therefore continuously developing
innovative, sustainable and useful solutions for their individual needs.
Together we set standards in Industrial Connectivity.
To find your local Weidmüller Distributor or Partner please visit www.weidmuller.com.au/au/distributors
Or contact your preferred supplier below:
Weidmüller Pty Ltd (Head Office)
43 Huntingwood Drive,
Huntingwood NSW 2148
Phone +61 (0) 2 9671 9999
Fax +61 (0) 2 9671 9900
Email info@weidmuller.com.au
www.weidmuller.com.au
Order number: WAUS Power Supplies Core Assortment Catalogue 2015 Australia & New Zealand
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising