PJD6544W User Guide (English)

PJD6544W User Guide (English)
PJD6345/PJD6544w
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS14971/VS14973
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yy
Reorient or relocate the receiving antenna.
yy
Increase the separation between the equipment and receiver.
yy
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yy
Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
i
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this unit near water.
Clean with a soft, dry cloth.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use of
certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the
European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
0.1%
< 0.1%
Lead (Pb)
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS2 Directives as noted below:
Examples of exempted components are:
1.Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other
lamps not specifically mentioned in the Annex of RoHS2 Directive
2.Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and
electronic ceramic parts (e.g. piezoelectronic devices)
3.Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead)
Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up to 0.4% lead by weight and as a cooper alloy containing up to 4%
lead by weight
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2013. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
Your LCD displays serial number is located on the rear side of the display.
For additional information, please see the “Customer Support” section in this guide.
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
For Your Records
PJD6345/PJD6544w
ViewSonic DLP Projector
VS14971/VS14973
PJD6345/PJD6544w_UG_ENG Rev. 1B 10-01-13
________________________________________
________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
iv
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type
AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recommend using a video source device
also equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Ground
Ground
For the U.S.A. and
Canada
For Australia and
Mainland China
Ground
Ground
For Continental Europe
For the U.K.
v
Table of contents
Introduction ........................................................................................... 1
Projector Features ................................................................................................................................. 1
Package Contents .................................................................................................................................. 2
Projector Overview ................................................................................................................................. 3
Using the Product ................................................................................. 5
Control Panel ......................................................................................................................................... 5
Connection Ports ................................................................................................................................... 6
Remote Control ...................................................................................................................................... 8
Installing the Batteries .......................................................................................................................... 11
Remote Control Operation ................................................................................................................... 12
Connection .......................................................................................... 13
Connecting a computer or monitor ....................................................................................................... 14
Connecting Video source devices ........................................................................................................ 16
Playing sound through the projector .................................................................................................... 18
Operation ............................................................................................. 20
Powering On/Off the Projector ............................................................................................................. 20
Adjusting the Projector Height ............................................................................................................. 21
Adjusting the Projector Zoom and Focus ............................................................................................. 21
Adjusting Projection Image Size .......................................................................................................... 22
Locking control keys ............................................................................................................................ 24
Setting the presentation timer .............................................................................................................. 25
Menu operation .................................................................................................................................... 26
Controlling the projector through a LAN environment .......................................................................... 38
Controlling the projector through a web browser ................................................................................. 41
Displaying images through vsPresenter .............................................................................................. 46
Displaying pictures with a USB storage device .................................................................................... 49
Maintenance ........................................................................................ 61
Cleaning the Lens ................................................................................................................................ 61
Cleaning the Projector Housing ........................................................................................................... 61
Replacing the Lamp ............................................................................................................................. 62
Specifications ...................................................................................... 64
Dimensions .......................................................................................................................................... 65
Ceiling mount installation ..................................................................................................................... 65
Appendix .............................................................................................. 66
LED Indicator Messages ...................................................................................................................... 66
Compatibility Modes ............................................................................................................................. 67
Troubleshooting ................................................................................................................................... 68
RS-232 Command and Configuration .................................................................................................. 69
IR Control Code ................................................................................................................................... 72
vi
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
• Single chip 0.55" Texas Instruments DLP® technology
• PJD6345: XGA (1024x768 pixel)
• Single chip 0.65" Texas Instruments DLP® technology
• PJD6544w: WXGA (1280x800 pixel)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
HDMI 1.4a support
PJLinkTM compatible
Support remote control with Crestron software
LAN display 4-1 (maximum 4 PC/ NB / smart phone / smart Pad display to 1
projector)
USB display supports computer connection via USB mini-B type to A type cable
Support USB flash drive for Photo / Video / music playback and office viewer
function
DynamicEco Timer function decreasing the power consumption of the lamp by up to
70% when no input signal can be detected for a set period of time.
Selectable quick power off function
Switchable normal and economic modes to reduce the power consumption
Support 3D DLP link technology
Less then 0.5w power consumption in standby mode.
Note
• The information in this manual is subject to change without notices.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
• The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
1
Package Contents
When you unpack the projector, make sure you have all these components:
Projector
AC Power Cord
VGA cable (D-SUB to DSUB)
Remote Control (IR) &
batteries (AAA *2 PCS)
ViewSonic CD Wizard
Quick Start Guide
Optional accessories
1. Ceiling mount kit
2. Replacement Lamp
3. VGA - Components adapter
Note
• Contact you dealer immediately if any items are missing, appear damaged, or if the unit
does not work.
• For maximum protection of the product, please save the original shipping carton and
packing materials and repack your product as it was originally packed at the factory if
you need to ship it.
2
Projector Overview
Front View
10
1
1.
3.
5.
7.
9.
9
2
3
8
4
Front IR remote control sensor
Projection lens
Security bar
Ventilation holes
Control panel
5 6 7
2. Elevator foot
4. Focus ring
6. Speaker
8. Zoom ring
10. Lamp cover
3
Rear View
2
1
3
1. AC power socket
3. Kensington lock
2. Connection ports
Bottom View
32
1
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
40
2
Unit: mm
150
1. Security bar
2. Ceiling mount holes
Note
• This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
• Contact your dealer for information to mount the projector on a ceiling.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a
fault should occur during operation of the unit, operate the disconnect device to switch
the power supply off, or disconnect the power plug.
4
Using the Product
Control Panel
2
3
4
T
O
E
P
M
P
1
W
E
ENTER
7
SOURCE
LA
M
P
R
8
MENU
EXIT
5
6
2
1. TEMP (Temp LED indicator)
Refer to “LED Indicator Messages”.
2. Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
3. POWER
Turn the projector on or off.
4. POWER (Power LED indicator)
Refer to “LED Indicator Messages”.
5. ENTER/Arrow key ( /Right)
Enacts the selected On-Screen Display (OSD) menu item.
When the On-Screen Display (OSD) menu is activated, #2 #5 and #7 keys are
used as directional arrows to select the desired menu items and to make adjustments.
6. MENU/EXIT
Display or exit the on-screen display menus.
7. SOURCE/Arrow key ( /Left)
Display the source selection bar.
8. LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
5
Connection Ports
2
3
12 11
10
1
13
4
5
6
7
8
9
1. AUDIO IN 1
Connect an audio output from the Computer In1 to this jack.
2. S-VIDEO
Connect S-Video output from video equipment to this jack.
3. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
4. COMPUTER OUT
Connect to a computer display, etc.
5. HDMI
Connect HDMI output from video equipment to this jack.
6. RS-232
When operating the projector via a computer, connect this to the controlling computer's RS-232C port.
7. TYPE B USB
This connector is for firmware update and mouse function support.
8. LAN
RJ45 connector for Ethernet connection.
9. MINI USB
USB display supports computer connection via USB mini-B type to A type cable.
10. COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
6
11. VIDEO
Connect composite video output from video equipment to this jack.
12. AUDIO OUT
Connect to a speaker or other audio input equipment.
13. AUDIO IN 2
Connect an audio output from the Computer In2 or video to this jack.
7
Remote Control
15
16
17
18
19
20
3
4
5
4
6
7
8
9
21
22
23
24
25
26
27
28
29
10
11
12
13
14
1. Power
Turn the projector on or off.
2. VGA1
Display COMPUTER IN 1 signal.
3. Source
Display the source selection bar.
4. Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
5.
Left
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys
are used as directional arrows to select the desired menu items and to make
adjustments.
6. My Button
User definable key for customized function
7. Menu
Display on-screen display menus.
8.
Right mouse
Perform the right button of the mouse when mouse mode is activated.
9.
Left mouse
Perform the left button of the mouse when mouse mode is activated.
10. Mouse
Switch between the normal and mouse modes.
11.
Lock
Activate panel key lock.
8
12. Pattern
Display embedded test pattern.
13. Blank
Hide the screen picture.
14. D.Eco
Decreases the power consumption of the lamp by up to 70%.
Note: It takes some time to initiate this function. Make sure the projector has been
turned on for more than 4 minutes.
15. Auto Sync
Automatically determines the best picture timings for the displayed image.
Note: Switch input source to Composite/S-Video/HDMI by sequence.
HMI only for PJD5234
16. Video
Switch input source to Composite/S-Video/HDMI by sequence.
17. VGA2
Display COMPUTER IN 2 signal.
18. Color Mode
Select the picture setup mode.
19. Enter
Confirmed selections.
20.
Right
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys
are used as directional arrows to select the desired menu items and to make
adjustments.
21. Exit
Goes back to previous OSD menu.
22. Page Up
Perform page up function when mouse mode is activated.
23. Page Down
Perform page down function when mouse mode is activated.
24. Magnify
Magnifies the projected picture size.
25. Volume
Adjust the volume level.
26. Freeze
Freeze the projected image.
27. Mute
Toggles the projector audio between on and off.
28. Aspect
Select the display aspect ratio.
29. Timer
Activate P-Timer OSD menu.
9
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer"
on page 14 for details.
2. Set the input signal to COMPUTER IN 1 or COMPUTER IN 2.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse
mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press /
• To left-click, press
• To right-click, press
/
/
.
.
.
• To operate your display software program (on a connected PC) which responds
to page up/down commands (like Microsoft PowerPoint), press Page Up/Page
Down.
• To return to the normal mode, press Mouse again.
10
Installing the Batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by the
diagram inside the compartment.
3. Close the battery cover into position.
Caution
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
• Remove batteries from remote control when not using for extended periods.
• Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
• Danger of explosion may happen if batteries are incorrectly replaced. Replce all the
batteries with new ones.
• Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
• If suspect battery leakage, wipe out the leakage and then replace new batteries.
• If the leakage adheres to your body or clothes, rinse well with water immediately.
11
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the
front
15
15
5m
8m
7m
Note
• Do not point the laser directly to the people's eyes (especially small children). There is a
danger of injury to the eyes.
• The remote control may not operate when there is sunlight or other strong light such as
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
• Do not get water on the remote control or place wet objects on it.
• Do not disassemble the remote control.
12
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
6
1
1
2
1
3
4
6
5
7
1.
3.
5.
7.
9.
Audio cable
Composite Video cable
VGA (D-Sub) to HDTV (RCA) cable
USB cable (B type to A type)
USB cable (mini-B type to A type)
2.
4.
6.
8.
8
9
HDMI cable
S-Video cable
VGA cable (D-Sub to D-Sub)
VGA to DVI-A cable
Important
• In the connections shown above, some cables may not be included with the projector
(see "Package Contents" on page 2). They are commercially available from electronics
stores.
• The connection illustrations above are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
• For detailed connection methods, see pages 14-18.
13
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
• Using a VGA cable
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
3. If you wish to use the remote paging function, take a USB cable and connect the A
type end to the USB port of the computer, and the other end to the TYPE B USB
socket on the projector. See "Using the remote mouse control" on page 10 for
details.
Important
• Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol
on the notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
• Using a USB cable
1. Take a USB cable and connect the type A end to the USB output jack of the
computer.
2. Connect the mini-B type end of the USB cable to the mini-B USB jack on the
projector.
3. Go to "My Computer", find a disk drive, then double click it to to install the USB
driver.
14
4. Double click “ViewSonic USB Mirror-only” icon on the desktop, and the ViewSonic
USB displays on the screen.
5. Select Mirror or Extension to display your contents.
Important
• ViewSonic USB function can’t support Mac OS devices.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the MONITOR OUT signal output socket on the projector to an
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on
page 14.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to
the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
Important
• In standby mode, the COMPUTER OUT output only works when COMPUTER IN 1 is
made to the projector.
15
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
• HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the
above connecting methods, however each provides a different level of video quality.
The method you choose will most likely depend upon the availability of matching
terminals on both the projector and the Video source device as described below:
Terminal name
Terminal appearance
HDMI
HDMI
S-VIDEO
S-Video
VIDEO
Video
Reference
"Connecting an
HDMI source
device" on page 16
"Connecting an SVideo source
device" on page 17
"Connecting a
composite Video
source device" on
page 18
Picture quality
Best
Good
Normal
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
16
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
•
VGA component adapter (ViewSonic P/N: CB-00008906)
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page
16 for details.
17
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 16 for details.
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and
also connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio
output of your Video source device to that sound system, instead of to the mono audio
projector.
You can also use a microphone to output the sound through the projector speaker.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Setting" on page 33 for details.
The table below describes the connection methods for different devices, and where
the sound is from.
Projector IO
Audio in 2 setting
Audio in 1
Audio in 2
Audio in
Audio in 1
Computer in 1
Audio in 2
Audio in 2
Computer in 1
Computer in 2
Composite
S-video
Microphone
Microphone
NA
Computer in 1
Computer in 2
Audio in 2
NA
Composite
S-video
The selected input signal determines which sound will be played by the projector speaker, and
which sound will be output from the projector when AUDIO OUT is connected. If you select a
PC signal; the projector can play the sound received from AUDIO IN 1/ AUDIO IN 2 or MIC.
Computer in 2
Composite
S-video
18
About the microphone input
• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the
projector.
• You can use a wireless microphone as long as a wireless module is attached to the
projector's microphone input jack and it works well with the associated devices.
• To ensure a quality use of the wireless microphone, it is recommended that your
microphone conforms to the specifications listed in the table below.
Signal
Microphone
Parameter
Transducer Principle
Impedance
Frequency response
Min
300
600
Type
Max
1K
16K
Dynamic
ohm
Hz
• There are two ways to adjust microphone volumes.
• Directly set microphone volume levels in the Video/Audio > Audio Setting >
Microphone Volume menu.
• Set projector volume levels in the Video/Audio > Audio Setting > Volume
menu, or press Volume keys (+, -) on the remote control. (The projector volume
setting will affect the microphone volume.)
• To make the microphone input available when the projector is in standby mode, turn
on the Video/Audio > Audio Setting > Active Audio Out menu.
• If the microphone is not working, check the volume setting and cable connection.
• You might get feedback noise from the microphone when you are too close to the
speaker of the projector. Move the microphone away from the speaker of the
projector. The greater volume you require, the greater distance you need to be
away from the Speaker to prevent the noise.
19
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press
to turn on the projector.
The projector takes a minute or so to warm up.
3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source when Auto source setting is ON.
• If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector to select your desired signal or press your desired
signal key on the remote control.
• If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed.
• Be sure the Quick Auto Search function in the SOURCE menu is On if you want
the projector to automatically search for the signals.
Warning
• Remove the lens cap first before powering on.
• Never look into the lens when the lamp is on. This can damage your eyes.
• This focal point concentrates high temperature. Do not place any object near it to avoid
possible fire hazard.
Powering Off the Projector:
1. Press
to turn off the projector lamp. You will see a message "Power off? Press
Power again" appear on the screen.
2. Press
again to confirm.
• When green mode is turned off, the Power LED begins flashing and the projector has entered stand-by mode.
• When green mode is turned on, the Power LED becomes steady light and the
projector has entered stand-by mode.
• If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-by
mode, simply press
to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
20
Adjusting the Projector Height
Elevator foot
The projector is equipped with an elevator foot to adjust the image height. To raise or
lower the image, turn the elevator foot to fine-tune the height.
Note
• To avoid damaging the projector, make sure that the elevator foot and tiltadjustment feet
are fully retracted before placing the projector in its carrying case.
Adjusting the Projector Zoom and Focus
Zoom ring
Focus ring
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image size by sliding the zoom ring.
21
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
PJD6345
4 : 3 Screen
Screen size
Diagonal
[inch (cm)]
(min. zoom)
(max. zoom)
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
40 (102)
62 (1.6)
69 (1.7)
24 (60.96)
3.6 (9.1)
60 (152)
94 (2.4)
103 (2.6)
36 (91.44)
5.4 (13.7)
80 (203)
125 (3.2)
137 (3.5)
48 (121.92)
7.2 (18.2)
100 (254)
156 (4.0)
172 (4.4)
60 (152.4)
9.0 (22.9)
150 (381)
234 (5.9)
257 (6.5)
90 (228.6)
13.5 (34.3)
200 (508)
312 (7.9)
343 (8.7)
120 (304.8)
18.0 (45.7)
250 (635)
390 (9.9)
429 (10.9)
150 (381.0)
22.5 (57.2)
300 (762)
468 (11.9)
515 (13.1)
180 (457.2)
27.0 (68.6)
Projection distance [inch (m)]
PJD6544w
16 : 10 Screen
Screen size
Diagonal
[inch (cm)]
(min. zoom)
(max. zoom)
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
40 (102)
51 (1.3)
61 (1.5)
21 (54)
2.6 (6.7)
60 (152)
76 (1.9)
91 (2.3)
32 (81)
4.0 (10.1)
Projection distance [inch (m)]
80 (203)
101 (2.6)
121 (3.1)
42 (108)
5.3 (13.5)
100 (254)
126 (3.2)
152 (3.9)
53 (135)
6.6 (16.8)
150 (381)
190 (4.8)
228 (5.8)
79 (202)
9.9 (25.2)
200 (508)
253 (6.4)
304 (7.7)
106 (269)
13.2 (33.7)
250 (635)
316 (8.0)
379 (9.6)
132 (337)
16.6 (42.1)
300 (762)
379 (9.6)
455 (11.6)
159 (404)
19.9 (50.5)
Note
• Position the projector in a horizontal position; other positions can cause heat build-up
and damage to the projector.
• Keep a space of 30 cm or more between the sides of the projector.
•
Do not use the projector in a smoky environment. Smoke residue may buildup on
critical parts and damage the projector or its performance
22
• Consult with your dealer for special installation such as suspending from a ceiling.
• There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should
physically test the projection size and distance using the actual projector in situ before
you permanently install it, so as to make allowance for this projector's optical
characteristics. This will help you determine the exact mounting position so that it best
suits your installation location.
23
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except
Power.
1. Press Lock on the remote control.
2. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock:
1. Press Lock on the remote control.
2. A confirmation message is displayed. Select Yes to confirm.
Important
• If you press
Power to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
• Keys on the remote control are still functional when panel key lock is enabled.
24
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to
utilize this function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to
the Option > Presentation Timer menu and press to display the Presentation
Timer page.
2. Highlight Timer Period and decide the timer period by pressing / .
3. Press to highlight Display Timer and choose if you want the timer to show up
on the screen by pressing / .
Selection
Always
1 Min/2 Min/3 Min
Never
Description
Displays the timer on screen throughout the presentation time.
Displays the timer on screen in the last 1/2/3 minute(s).
Hides the timer throughout the presentation time.
4. Press to highlight Timer Position and set the timer position by pressing
Top-Left → Bottom-Left → Top-Right → Bottom-Right
/
.
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
Selection
Count Up
Count Down
Description
Increases from 0 to the preset time.
Decrease from the preset time to 0.
6. To activate the presentation timer, highlight Start Counting and select Start
Counting. You will see the message displaying on the screen.
7. To cancel the timer, go to the Option > Presentation Timer > Start Counting
menu and highlight Off.
25
Menu operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
How to operate
1. Press MENU/EXIT on the projector or Menu on the remote control to open the
OSD menu.
2. When OSD is displayed, use / to select any feature in the main menu.
3. After selecting the desired main menu item, press to enter sub-menu for feature
setting.
4. Use / to select the desired item and adjust the settings with / .
5. Press MENU/EXIT on the projector or Menu on the remote control, the screen will
return to the main menu.
6. Press MENU/EXIT twice* on the projector or Exit on the remote control to leave
and save the settings.
*The first press leads you back to the main menu and the second press closes the
OSD menu.
26
Menu tree
Main Menu
Sub Menu
Color Mode
Settings
RGB: Brightest / PC / Movie / ViewMatch / User1 /
User2 / White Board / Black Board / Green Board
Video: Brightest / Game / Movie / ViewMatch /
User1 / User2 / White Board / DICOM SIM / Green
Board
Reference Mode RGB: Brightest / PC / Movie / ViewMatch
Video: Brightest / Game / Movie / ViewMatch
Brightness
0 - 100
Contrast
0 - 100
Color Temp.
User / Cool / Normal / Warm
Red Gain
0 - 100
Color Setting
Green Gain
0 - 100
Blue Gain
0 - 100
Color
Red / Green / Blue / Cyan /
Magenta / Yellow
Picture
Hue
-99 - +100
User Color
Saturation
0 - 199
Gain
0 - 199
White Intensity
0 - 10
Gamma
1-8
XGA: Auto/ 4:3/ 16:9 / Wide
Aspect Ratio
WXGA: Auto/ 4:3/ 16:9 / 16:10* / Anamorphic
* 16:10 only for PJD6544w
Dynamic Mode
On / Off
Keystone
-40 - +40
3D Sync
On / Off
3D Format
Auto / Frame Sequential /
3D Settings
Frame Packing / Top-Bottom /
Side-by-Side
3D Invert
On / Off
Frequency
0 - 31
Tracking
-5 - +5
H Position
-10 - +10
V Position
-10 - +10
Zoom
0 - +5
Sharpness
0 - 31
Video/Audio Video Setting
Tint
0 - 100
Saturation
0 - 100
Volume
0 - 10
Mute
On / Off
Audio Setting
Audio in 2
Audio In / Microphone In
Microphone
0 - 10
Volume
27
Projector
Projection
Menu Setting
HDMI Format
HDMI Range
Blank Screen
Message
Auto Source
Auto Power Off
Sleep Timer
Setting
Standby Setting
LAN Control
Setting
Front-Table / Front-Ceiling / Rear-Table / RearCeiling
Menu Position
Top-Left / Top-Right / Center /
Bottom-Left / Bottom-Right
Menu Display Time 5 - 60 Sec
OSD Transparency Off - 90
DVI: RGB Enhance / RGB Normal / YCbCr
HDMI: Auto / RGB Full / RGB limited / YCbCr
Normal / Enhance
Black / Red / Green / Blue / Cyan / Yellow / Magenta
/ White
On / Off
On / Off
Off - 60 Minute
Off -12 Hours
Network
On / Off
Active VGA Out
On / Off
Active Audio Out On / Off
Quick Power Off
On / Off
Smart Restart
On / Off
DC12V
On / Off
Status
Disconnect /
Connect
DHCP
On / Off
Projector IP address
Wired LAN
Subnet Mask
Default Gateway
DNS Server
Apply
Status
SSID
Wireless LAN
IP Address
Connection Mode
Network Restart
Restrat / Cancel
28
Closed Caption
Password
Presentation
Timer
Option
High Altitude
Lamp Setting
My Button
Pattern
CEC
Factory Default
Off/ CC1~CC4/ T1~T2
Change Password Input new
Confirm
password
password
Password
Yes / No
Password Delete Input
Password Delete
currently
Yes/No
password
Timer Period
0 - 240 Min
Display Timer
Always / 1 Min / 2 Min / 3 Min /
Never
Timer Position
Top-Left / Bottom-Left / TopRight / Bottom-Right
Timer Counting
Count Down / Count Up
Direction
Start Counting
Start Counting / OFF
On / Off
Lamp Hours
Lamp Hours Reset Yes / No
Eco Mode
On / Off
Dynamic Eco
Off / 5 / 10 / 15 / 20 / 25 / 30
Timer (RC)
min
Brightness / Contrast / Color Setting / Projector
Projection / Menu Position / 3D Setting / Eco Mode /
Dynamic Mode / OSD Transparency / Closed
Caption / Auto Power Off / Sleep Timer / Auto
Source
Off / 1 / 2 / 3 / 4 / 5 / User
On / Off
Yes / No
Language
Information
Input Source
Resolution
H. Frequency
V. Frequency
Lamp Hours
Mac Address
29
Picture
Color Mode
There are many factory presets optimized for various types of images.
• Brightest: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required.
• PC: Is designed for presentations under daylight environment to match PC and
notebook coloring.
• Game: Is appropriate for playing games.
• Movie: Is appropriate for playing colorful movies. This mode is suitable for viewing
in a blackened (little light) environment
• ViewMatch: Switches between high brightness performance and accurate color
performance.
• User 1:Memorize user 1 defined settings.
• User 2:Memorize user 2 defined settings.
• White Board:For white projection screen type.
• DICOM SIM:.Recommended for DICOM format files in simulation mode.
• Green Board:For green projection screen type.
Note
• DCIM SIM option is only for training or reference. It not used for actual diagnosis.
• DICOM represents for the Digital Imaging and Communications in Medicine. This is a
standard created by the American College of Radiology and the National Electrical
Manufacturers Association. This standard specifies the method of digital image data to
be transferred from one system to another.
Reference Mode
Select a picture mode that best suits your need for the image quality and further finetune the image. This function is only available when User 1 or User 2 is selected.
• Brightest: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required.
• PC: Is designed for presentations under daylight environment to match PC and
notebook coloring.
• Game: Is appropriate for playing games.
• Movie: Is appropriate for playing colorful movies. This mode is suitable for viewing
in a blackened (little light) environment
• ViewMatch: Switches between high brightness performance and accurate color
performance.
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
30
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red Gain, Green Gain, Blue Gain) to customize user color
temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range, hue, saturation and gain according
to your preference.
White Intensity
Increase the brightness of white areas.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
Aspect Ratio
Select how the picture fits on the screen:
• Auto: Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width. You want to make most use of the screen without
altering the source image’s aspect ratio.
• 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3
aspect ratio.
• 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio.
• 16:10: Scales an image so that it is displayed in the center of the screen with a
16:10 aspect ratio.
• Wide / Anamorphic: Minimizes the aspect ratio distortion by maintaining close to
the original aspect ratio in the center of the image and distributing the majority of
distortion at the edges of the displayed image.
Note
• Wide for XGA model; Anamorphic for WXGA model.
• 16:10 only for PJD6544w model .
Dynamic Mode
Choose “On” to dim the projector lamp which will automatically detect the brightness
level of the content and reduce lamp power consumption (up to 70 percent). Choose
“Off” to turn off Dynamic Mode.
Note
• When Dynamic Mode is “On”, Eco Mode will be gray out.
Keystone
Manually correct distorted images resulting from an angled projection.
Press Keystone / on the projector or remote control to display the Keystone
correction page.
Press to correct keystone at the top of the image.
Press to correct keystone at the bottom of the image.
31
3D Settings
This projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
3D Sync
When you discover the inversion of the image depth, enable this function to correct
the problem.
3D Format
Use this function to choose an appropriate 3D format if the projector cannot recognize
the 3D format.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects
the signal for 3D Sync information and once detected, it projects images in 3D format
automatically. In other cases, you may need to manually select a 3D Sync format for
the projector to project 3D images correctly.
Note
• 3D Format will be available when 3D Sync is “On”.
• The default setting is “Auto” when input source is HDMI.
• The default setting is “Side-by-Side” when input source is video or computer. “Auto”
will be unavailable.
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
3D Invert
• On: Invert left and right frame contents.
• Off: Default frame contents.
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Note
• This functions is only supported under computer mode.
Tracking
Adjust the phase of the projector relative to the computer.
Note
• This functions is only supported under computer mode.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
32
Zoom
Using the remote control
1. Press Magnify on the remote control to display the Zoom bar.
2. Press
/
to magnify the picture to a desired size.
3. Press “Enter” on the projector or remote control to switch to the paning mode and
press the directional arrows to navigate the picture. The zoom bar needed to be
shown on screen if we want to switch the paning mode.
4. To reduce size of the picture, press Magnify and press
restored to the original size.
repeatedly until it is
Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
until the Video/Audio menu is highlighted.
2. Press
to highlight Zoom.
3. Repeat steps 2-4 in the section of Using the remote control above.
Video Setting
Allow you to enter the Video Setting menu.
• Sharpness: Sharpen or soften the image.
• Tint: Shift colors toward red or green.
• Saturation: Adjust a video image from black and white to fully saturated color.
Audio Setting
Allow you to enter the Audio Setting menu.
• Volume: Adjust the projector’s volume level.
• Mute: Toggles the projector audio between on and off.
• Audio In: Switch Audio in 2 function for Audio in or Microphone in function.
• Microphome Volume: Adjust the microphone’s volume level.
Setting
Projector Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Menu Setting
Allow you to enter the Menu Setting menu.
• Menu Position: Choose the menu location on the display screen.
• Menu Display Time: Duration of OSD menu display countly starts (at idle state by
second).
• OSD Transparency: Select to change the transparency level of the OSD
background.
33
HDMI Format
Selects appropriate HDMI format automatically or manually.
Note
• This function is only available when the HDMI-input port is in use.
• When HDMI Format is “Auto”, HDMI Range will be gray out.
HDMI Range
• Enhanced: The range for HDMI output signal is from 0 - 255.
• Normal: The range for HDMI output signal is from 16 - 235.
Blank Screen
To select the screen color when Blank function is active.
Message
Enable or disable the message box at the right bottom of the screen.
Auto Source
Automatically scan through all the input source if the function in the OSD menu is On.
The function will stop the signal auto scan process and fix the signal source you
preferred if you turn Off the Auto Source.
Auto Power Off
Allows the projector to turn off automatically if no input signal is detected after a set
period of time.
Sleep Timer
No matter whether the projector detect signal or not, the projector will turn off
automatically when the countdown has finished.
Standby Setting
Network
Set whether the network function works when the projector is in standby (powered off
but connected to AC power).
Note
• Less than 0.5W power consumption when network is turned OFF.
• When Power Saving is On, the Active VGA out and Active Audio out settings are not
available.
Active VGA Out
Set whether the VGA OUT function works when the projector is in standby (powered
off but connected to AC power).
Active Audio out
Set whether the audio out function works when the projector is in standby (powered
off but connected to AC power).
Quick Power Off
• On: The projector will directly shut down without cooling procedure.
• Off: The projector will shut down following normal cooling procedure.
34
Smart Restart
Selecting On enables you to restart the projector immediately within 3 minutes after
turning it off. After 3 minutes, if the projector is not turned on again, it will directly enter
the standby mode.
DC12V
Set whether the DC12V function works when the projector is in standby (powered off
but connected to AC power).
LAN Control Setting
Wired LAN
Allow you to configure the wired LAN settings. Refer to page 38.
• Status: Display the projector’s status.
• DHCP: Abbreviation for Dynamic Host Configuration Protocol. This protocol
automatically assigns IP Address to networked devices.
• When the “DHCP” sets to “On”, it takes some time to obtain IP address from
DHCP server.
• When the "DHCP" sets to "Off", that means user will set IP address by manually.
• Projector IP Address: Numerical address to identify networked computers. This
function can only be used when DHCP is set to Off.
• The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Subnet Mask: A numeric value to define the number of bits used for a network
address of a divided network (or subnet) in an IP Address. This function can only be
used when DHCP is set to Off.
• The Subnet Mask “0.0.0.0” is prohibited.
• Default Gateway: A server (or router) to communicate across networks (subnets)
that are divided by Subnet Mask. This function can only be used when DHCP is set
to Off.
• DNS Sever: Setup DNS server address when DHCP is disable.
• Apply: Save and execute the wired LAN settings.
Wirless LAN
Allow you to configure the wireless LAN settings. Refer to page 39.
• Status: Display the projector’s status.
• SSID: Display the projector’s SSID information.
• IP Address: Numerical address to identify networked computers. This function can
only be used when DHCP is set to Off.
• The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Connection Mode: Methods for connecting to wireless networks with Wi-Fi enabled
devices.
35
Network Restart
If you encounter a malfunction of network connection and need to restart the network
settings, you can go into the Setting > LAN Control Setting > Network Restart
menu to restart network function.
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Password
Set, change or delete the password. When the password function is added, image
projection will require to input the preset password when turning on the projector.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
Lamp Setting
Allow you to enter the Lamp Setting menu.
• Lamp Hours: Display the lamp’s elapsed operating time (in hours).
• Lamp Hours Reset: Reset the lamp Hour to 0 hours.
• Eco Mode: Use this function to dim the projector lamp light output which will lower
power consumption and increase lamp life.
• Dynamic Eco Timer (RC): Sets the timer of triggering Dynamic Eco function. The
projector lamp will start dimming when the timer period has finished.
My Button
Allow user to define a short cut key on the remote control, and the function item is
selected in OSD menu.
Pattern
The projector can display several test patterns. It helps you adjust the image size and
focus and check that the projected image is free from distortion.
CEC
If the projector is connected to a DVD player with HDMI cable, selecting On will
activate the DVD player at a time when powering on the projector.
Factory Default
Restore settings to factory default.
Note
• The following settings will still remain: Keystone, Password, Projector Projection, High
Altitude and Language.
36
Language
Select the language used by the on-screen menu.
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
MAC Address
Display the MAC address.
37
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when
they are properly connected to the same local area network.
Wired connection
Internet
IP Router
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press MENU/EXIT on the projector or Menu on the remote control and then go to
Setting > Lan Control Setting menu.
3. Highlight Wired LAN and press ENTER on the projector or Enter on the remote
control.
4. Make sure the Status is Connect.
5. Press
to highlight DHCP and press
/
to select On.
6. Press
to highlight Apply and press ENTER on the projector or Enter on the
remote control.
7. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page.
The Projector IP Address, Subnet Mask, Default Gateway, and DNS Sever
settings will be displayed. Note down the IP address displayed in the Projector IP
Address row.
Important
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press
to highlight DHCP and press
/
to select Off.
3. Contact your ITS administrator for information on the Projector IP Address,
Subnet Mask, Default Gateway, and DNS Sever settings.
38
4. Press
to select the item you want to modify and press ENTER on the projector
or Enter on the remote control.
5. Press
/
to move the cursor and the enter the value.
6. To save the settings, press ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
7. or Menu on the remote control.
8. Press
to highlight Apply and press ENTER on the projector or Enter on the
remote control.
Important
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
Wireless connection
ViewSonic wireless dongle
P/N: WPD-100
To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle
(optional) to the Type A USB connector on the projector, and then only a few OSD
configuration steps are required.
1. Make sure the projector is turned on.
2. Press MENU/EXIT on the projector or Menu on the remote control and then go to
Setting > LAN Control Setting menu.
3. Highlight Wireless LAN and press ENTER on the projector or Enter on the remote
control.
4. Make sure the Status is Connect.
5. Make sure the SSID information is displayed.
6. In AP mode, you need to use your computer’s wireless connection utility to search
the projector’s SSID and connect to it. The password of connection the Wi-Fi for
the first time is “87654321”. Then you can search the projector with vsPresenter.
To use Client mode, you should connect both your computer and projector to the
same AP router and make connections with the IP address.
39
About AP and Client modes
In AP mode, you need to use your computer's wireless connection utility to search for the
projector's SSID and connect to it. Then you can search for the projector with vsPresenter.
In Client mode, you should connect both your computer and projector to the same AP
router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Client modes.
(AP Mode)
(Client Mode)
Internet
Internet
Important
• If you need more information about AP and Client modes, please refer to user
documentations for Wireless Routers which are usually available on 3C stores.
40
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in
standby mode, you can use any computer that is on the same local area network to
control the projector.
Important
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
• The screenshots in this manual are for reference only, and may differ from the actual
design.
1. Enter the address of the projector in the address bar of your browser and press
Enter.
2. The ViewSonic Network Control webpage opens.
3. Click Administrator Login and enter the default password “0000” to login.
41
4. The main page of the ViewSonic Network Control webpage appears as below.
5
6
7
8
9
10
5. To change the language for the web pages, click the down arrow to reveal a drop
down list and select a desired language.
6. To download vsPresenter, click PC or MAC depending on your computer operating
system. See "Displaying images through vsPresenter" on page 46 for details.
7. Wireless page displays the Wireless Lan information.
8. Network Settings: Provides network settings.
9. Email Alert: Allows you to setup the mail server and send system error messages
to your ITS administrator.
10. The Crestron (eControl) page displays the Crestron eControl user interface. See
"About Crestron control" on page 42 for details.
About Crestron control
1. The Crestron (eControl) page displays the Crestron eControl user interface. The
eControl page provides a variety of virtual keys to control the projector or adjust
the projected pictures.
i
i
ii
You can press
/ to reveal
more buttons.
i.
i
These buttons function the same as the ones on the OSD menus or remote
control.
42
ii. To switch between input signals, click on your desired signal.
Important
• The Menu button can also be used to go back to previous OSD menus, exit and save
menu settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
2. The tools page allows you to manage the projector, configure the LAN control
settings and secure access of remote network operation on this projector.
i
ii
iii
v
iv
i.
This area is only used with a Crestron Control System. Please contact Creston
or refer to the Crestron user manual for setup information.
ii. This area is used for naming the projector, associating it with a particular location, assigning a responsible party to it, and adjusting network settings.
iii. This area is used to set User and Admin passwords. When password protection is enabled, unauthorized changes to the projector configuration will be
avoided.
Important
• To prevent errors, only input the English alphabet and digits on the tools page.
• After making the adjustments, press the Send button and the data will be saved for the
projector.
iv. Press Exit to go back to the remote network operation page.
43
Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
Category Item
Input Length
Maximum Number of
Characters
Crestron Control
IP Address
15
IP ID
2
Port
5
Projector
Projector Name
10
Location
9
Assigned To
9
Network Configuration
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
User Password
Enabled
(N/A)
New Password
20
Confirm
2
Admin Password
Enabled
(N/A)
New Password
20
Confirm
20
3. The info page displays the information and status of this projector.
Press exit to go back to the Crestron remote network operation page.
44
4. After pressing the button “Contact IT Help”, the Title window will appear in the
upper right corner of the screen. You will be able to deliver messages to
RoomView software administrators/users who connect to the same local area
network.
Important
• Please only deliver the messages in English letters and digits.
For more information, visit http://www.crestron.com and www.crestron.com/
getroomview.
**Crestron RoomView
On the "Edit Room" page, enter the IP Address (or hostname) as shown on the
projector's on-screen display (OSD) menu, and "05" for IPID, "41794" for the reserved
Crestron control port.
About Crestron RoomView setting and command method, please access below
website to get RoomView User Guide and more information:
http://www.crestron.com/features/
roomview_connected_embedded_projectors_devices/resources.asp
45
Displaying images through vsPresenter
Downloading and installing vsPresenter
The vsPresenter is an application running on the host PC. It helps connect your
computer to an available network projector and transfer the desktop content to the
network projector via local network connection.
1. Enter the main page of Network Control. See steps 1-2 on page 41 for details.
2. Download vsPresenter.
3. When the download is complete, install the software to your computer by clicking
the exe file. Follow the on-screen instructions to complete the installation.
4. Launch vsPresenter.
5. Select display zone by clicking 1, 2, 3, 4, L, R, All, or Background and then enter
the password. The default password is “0000”.
Using vsPresenter
1
6
2
5
3
4
1. The Search page allows you to search and connect to a projector.
i.
To connect to a projector, select Directly then type the projector IP address and
click Connect.
46
ii. To search for projectors, simply click Search to list all the projectors on the
same local area network. Click the desired projectors in the Search result list,
and click Connect directly. You can also type a desired projector name and
click Search.
iii. You can link to the ViewSonic webpage control system on page 42.
2. If you want to freeze the projected image on the screen, press . Any further
movements will be not been seen on the screen until is pressed.
3. You can choose a mirror mode or extension mode from here.
i. Mirror mode is to display the content in your computer.
ii. Extension mode is to extend the computer’s display to the projected screen.
4. The Setting page allows you to configure vsPresenter.
i. To use Compatible Mode, click On.
ii. To use Audio Streaming, click On. Click Apply.
iii. To select the image quality for video or presentation, click the down arrow to
reveal a drop-down list and select a desired quality type.
iv. The Software Information is available on this page.
47
5. You can manage the connected projectors listed under vsPresenter Management.
• Under a conference mode:
1. Only the administrator can take control.
2. A projector can display up to 4 computer screens.
• You can set the name of your computer under vsPresenter Management.
• For details about the icons, please see the following:
Icon
Description
Icon
You are a normal user and
have no access to change the
password.
You are an administrator and
have authority to change the
password.
You are the user of the
projector.
You are an administrator of the
projector.
Sets a display zone for the projector.
Description
Disconnects from the projector.
Opens the web page of the
Network Control.
There is another user of the
projector.
You are a normal user of the
projector.
6. Disconnect
To disconnect from the projector(s), click the Disconnect icon.
Important
• Be sure to turn off other virtual network control programs before using vsPresenter.
48
Displaying pictures with a USB storage device
The projector is built-in an application which can display packaged images on a USB
storage device. It can eliminate the need for a computer source.
To display the images on a USB storage device:
1. Plug the USB storage device into the TYPE A USB socket.
2. Press the Source button and choose the USB A (Type-A) input. Note: If no other
sources are connected and Auto Source is on, the projector will automatically
select the USB A source.
3. Press Enter and use /
to select one of the EZ Media mode.
Photo mode
49
Folders and supported files are represented in thumbnail mode.
Press button
Up
Down
Left
Right
Enter
Exit
Action
Scroll through the thumbnails
Open a file
Go back to Photo mode
Displaying a picture
• Press AutoSync on the remote control to display OSD control menu.
Press button
Action
Up
Go to previous photo.
Down
Go to next photo.
Enter
Start slideshow.
Exit
Go back to thumbnail file.
50
Slideshows
• Photo slideshow duration time includes 2 sec, 5, sec and 10 sec.
51
Audio mode
Audio playlist is displayed on the screen.
Press button
Up
Down
Enter
Exit
Action
Go to previous audio
Go to next audio
Play audio
Go back to Audio mode
52
When audio is playing
Press button
Up
Down
Left
Right
Enter
Exit
Action
Go to previous audio
Go to next audio
Fast backward play
Fast forward play
Play/pause
Go back to playlist
53
Video mode
Video playlist is displayed on the screen.
Press button
Up
Down
Enter
Exit
Action
Go to previous video
Go to next video
Play video
Go back to Video mode
54
When video is playing
• The OSD control menu displays for few seconds. To display it again, press
Enter.
Press button
Action
Up
Go to previous video
Down
Go to next video
Left
Fast backward play
Right
Fast forward play
Enter
Play/pause
Exit
Go back to playlist
55
Office Viewer mode
Office file list is displayed on the screen.
Press button
Up
Down
Enter
Exit
Action
Go to previous file
Go to next file
Open a file
Go back to Office Viewer mode
Note
• PJD6345 support up to 1600x1200 resolution.
• PJD6544w support up to 1680x1050 resolution.
56
When Office file is displaying
Press button
Up
Down
Left
Right
Exit
Action
Page up
Page down
Zoom out
Zoom in
Go back to file list
Settings
System
Version
Language
Update
Output Mode
Video
Display Ratio
Repeat Mode
Audio
Repeat Mode
Photo
Display Ratio
Slideshow
Slideshow Duration
Description
Display current EZ Media firmware version.
Sets EZ Media on-screen display language.
Sets update method.
Sets output mode.
Description
Sets display ratio.
Sets repeat mode.
Description
Sets repeat mode.
Description
Sets display ratio.
Sets whether to activate slide shows.
Sets the time interval each image displays.
57
Supported file formats
1. Images
Image Format
Profile
Color Space
YUV400
YUV420
YUV422
YUV440
YUV444
YUV400
YUV420
YUV422
YUV440
YUV444
No limit
Baseline
JPEG
Progressive
BMP
No limit
Size Limitation
No limit
No limit
No limit
No limit
No limit
Width <= 10240 &&
height <= 6400
No limit
2. Audio
Audio Format
OGG
ADPCM-WAV
PCM-WAV
AAC
Sample rate (KHz)
8-48
8-48
8-48
8-48
Bit Rate (Kbps)
64-320
32-384
128-1536
8-256
3. Voice Record
File Format
Audio Format
.wav
IMA-ADPCM
Sample rate (KHz)
8
16
24
48
58
Bit Rate (Kbps)
32
64
192
384
4. Video
File
Extensions
Audio/Video
Profile/
Explanation
Level Support
No limit
Up to High Profile ,
Support less than 4
Levels 1- 4.1 (1080P
reference frames
30fps 20Mbps)
Up to Advance Simple profile (1080P
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Advanced Simple Profile (frame picture) ,
Levels 0-5 (1080P
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Up to High Profile ,
Support less than 4
Levels 1- 4.1 (1080P
reference frames
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P D-picture not support
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Codec
MJPEG
H.264/AVC
.avi
.divx
.mkv
XVID
Video
MPEG2
MPEG4
MPEG2
.ts
Video
H.264/AVC
MPEG1
.dat
.vob
.mpg
.mpeg
Video
MPEG2
Audio
MPEG-1 Layer I, II
MPEG-1 Layer III
(mp3)
Advanced Simple Profile (frame picture) ,
Levels 0-5 (1080P
30fps 20Mbps)
Up to High Profile ,
Levels 1- 4.1 (1080P
30fps 20Mbps)
MPEG4
.mov
.mp4
Video
H.264/AVC
Support less than 4
reference frames
5. Subtitle
Format
Font
Standard SRT
UTF-8 / UTF-16
Subtitle Size
4bits up to 448x200
2bits up to 896x200
Note: DO NOT support mixed code in subtitle files.
6. Picsel Office Viewer
File Format
Adobe PDF
Support Version
PDF 1.0
PDF 1.1
PDF 1.2
PDF 1.3
PDF 1.4
Pages/Lines Limitation
Size Limitation
Comment
Up to 1000 pages (One
File)
Up to 50MB
-
59
MS Word
MS Excel
MS PowerPoint
British Word 95.
Because office viewer does
Word 97, 2000,2002,
not load all pages of MS
2003.
Word file at the same time,
Word
there are no obvious
2007(.docx),2010(.d
limitations of page and line.
ocx)
British Excel 5, 95.
Row Limit: up to 595
Excel 97, 2000,
Column Limit: up to 256
2002, 2003.
Excel
2007(.xlsx),2010
Sheet: up tp 100
(.xlsx).
Note: Any one of three
limitations above can not
Office XP Excel.
appear on one excel file
simultaneously
British
PowerPoint 97.
PowerPoint 2000,
2002, 2003.
PowerPoint
2007(.pptx).
PowerPoint
Up to 1000 pages
2010(.pptx),.
(One File)
Office XP
PowerPoint.
PowerPoint
presentation- -2003
andearlier(.ppx)
PowerPoint
presentation- -2007
and 2010(.ppsx)
60
Up to 50MB
Not support Bold
Text in Simple
Chinese front
Up to 15MB
Not support
password-protected sheets
Up to 19MB
No support
SlideShow order
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
• Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Note
• Turn off the projector and remove the AC power cord from the power outlet before
beginning maintenance work.
• Make sure the lens is cool before cleaning.
• Do not use detergents or chemicals other than those noted above. Do not use benzene
or thinners.
• Do not use chemical sprays.
• Use a soft cloth or lens paper only.
61
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
Type number:
PJD6345
RLC-084
PJD6544w
RLC-084
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of
use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness,
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of
mercury fumes. Otherwise it could be harmful to user’s health.
62
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Option > Lamp Setting” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
• Do not use the projector with the lamp cover removed.
63
Specifications
Model name
Display system
Resolution
Optical Zoom
F/No.
Focal length
Screen size
Lamp
Input terminal
Output terminal
Control terminal
Speaker
Video compatibility
PJD6345
Single 0.55" DLP panel
XGA
(1024 × 768)
1.1X
1.97 - 2.17
21.95 - 24.18mm
30” - 300”
PJD6544w
Single 0.65" DLP panel
WXGA
(1280 × 800)
1.2X
2.58
21 - 25.6mm
30” - 300”
240W
D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5
mm stereo mini jack) x 2, HDMI x 1, 3.5 mm Mic input x1, Type A
USB x1 (supports USB flash drive display and wireless dongle for
USB display), Type mini-B USB x1 (supports USB display)
D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x
1
RS-232 x 1, Type B USB x 1 (supports firmware upgrade and
remote mouse control), RJ45 x 1, 12-Vdc trigger output x 1
16 watt x 1
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
31 - 100 KHz
24 - 120 Hz
Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Environment
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement
AC 120-240 V, 50 - 60 Hz, 3.2A
Power consumption
315 W (Max.)
Dimension (W x D x H)
294 x 219 x 113 mm
Weight
2.1 kg (4.6 lbs)
Note: Design and Specifications are subject to change without prior notice.
64
Dimensions
294 mm (W) x 219 mm (D) x 113 mm (H)
294
85
219
113
72
Ceiling mount installation
32
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
40
150
65
Appendix
LED Indicator Messages
LED Type
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Power LED
Temp LED
Lamp LED
Color
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Status
Solid
Off
Off
Flash
Off
Off
Flash
Off
Off
Solid
Off
Off
Solid
Off
Off
Solid
Flash
Flash
Solid
Off
Flash
Power LED
Temp LED
Lamp LED
Blue
Red
Red
Flash
Flash
Off
Power LED
Temp LED
Lamp LED
Blue
Red
Red
Flash
Off
Solid
Meaning
Standby mode when green mode is turned
on.
Standby mode when green mode is turned
off.
Powering up
Normal operation
Powering down
If the projector system has some problems
with its fans, the projector will shut down.
The lamp has reached its end of life and
must be changed soon. The lamp will
continue to operate until it fails. Change the
lamp. If the lamp is off, then the ballast will
become malfunction.
1. Temperature is too high. The lamp will
turn off. The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after
the projector is shut down and re-started
right away.
The lamp ignition failed. If temperature is
too high, the fans will cool the lamp.
66
Compatibility Modes
Computer:
Resolution
640 x 350
H-Sync [KHz]
37.9
24.6
31.5
37.9
37.5
43.3
61.9
31.5
37.9
31.0
35.2
37.9
48.1
46.9
53.7
76.3
48.4
56.5
60.0
68.7
97.6
67.5
47.8
60.0
85.9
64.0
65.3
75.0
65,3
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 768
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1680 x 1050
V-Sync [Hz]
85.0
50.0
59.9
72.8
75.0
85.0
120.0
70.0
85.0
50.0
56.0
60.3
72.0
75.0
85.1
120.0
60.0
70.1
75.0
85.0
120.0
75.0
60.0
60.0
85.0
60.0
60.0
60.0
60,0
Video:
Compatibility
480i
480p
576i
576p
720p
720p
1080i
1080i
1080p
1080p
Resolution
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
H-Sync [KHz]
15.8
31.5
15.8
31.3
37.5
45
33.8
28.1
67.5
56.3
67
V-Sync [Hz]
60
60
50
50
50
60
60
50
60
50
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
• Be sure that the power cord is securely connected to the projector and the other end is
plugged into an outlet with power.
• Press the power button again.
• Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
• Press SOURCE on the projector or Source on the remote control to select an
active input source.
• Be sure the external source is turned on and connected.
• For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
• Be sure the lens cover is removed.
• While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
• Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
• Press Auto Sync on the remote control.
• Press MENU on the projector or Menu on the remote control, go to Video/Audio and
adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
• Be sure nothing is blocking the remote control receiver on the front of the projector.
Use the remote control within the effective range.
• Aim the remote control at the screen or at the front or back of the projector.
• Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.
68
RS-232 Command and Configuration
D-Sub 9 pin
1
2
3
4
5
6
7
8
9
Wire List
1 CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
C1
1
2
3
4
5
6
7
8
9
SHELL
Baud Rate
Data Length
Parity Check
Stop Bit
Flow Control
COLOR
Black
Brown
Red
Orange
Yellow
Green
Blue
Purple
White
DW
115200 bps (default)
8 bit
None
1 bit
None
69
C2
1
3
2
6
5
4
8
7
9
SHELL
Function
Power
Source input
Projector position
OSD
Lamp
Fan
Keystone
Aspect ratio
Blank
Freeze
Volume
Auto source
Action
Power on
Power off
Computer1
Computer2
S-Video
Video
HDMI
Front table
Rear table
Front ceiling
Rear ceiling
Menu
Up
Down
Left
Right
ECO on
ECO off
Using hours
High Attitude on
High Attitude off
Keystone up
Keystone down
4:3
16:9
Anamorphic/Wide
Auto
Blank on
Blank off
Freeze on
Freeze off
Volume +
Volume Mute on
Mute off
Auto source on
Auto source off
Control Code
BE,EF,10,05,00,C6,FF,11,11,01,00,01,00
BE,EF,03,06,00,DC,DB,69,00,00,00,00,00
BE,EF,03,19,00,19,29,01,47,02,CC,CC,00
BE,EF,03,19,1E,90,72,01,47,02,CC,CC,00
BE,EF,03,19,00,E8,69,01,47,02,CC,CC,00
BE,EF,03,19,00,78,A8,01,47,02,CC,CC,00
BE,EF,03,19,00,DA,2B,01,47,02,CC,CC,00
BE,EF,10,07,9F,9D,0E,0A,EF,00,00,00,00
BE,EF,10,07,9F,9D,0E,0A,EF,01,00,00,01
BE,EF,10,07,9F,9D,0E,0A,EF,02,00,00,02
BE,EF,10,07,9F,9D,0E,0A,EF,03,00,00,03
BE,EF,02,06,00,E9,D3,30,00,00,00,00,00
BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
BE,EF,02,06,00,0B,D2,32,00,00,00,00,00
BE,EF,02,06,00,DA,D3,33,00,00,00,00,00
BE,EF,02,06,00,38,D2,31,00,00,00,00,00
BE,EF,03,06,00,EF,DB,6A,00,00,00,00,00
BE,EF,03,06,00,3E,DA,6B,00,00,00,00,00
BE,EF,03,06,00,BA,DB,6F,00,00,00,00,00
BE,EF,02,06,00,40,D3,80,00,00,00,00,01
BE,EF,02,06,00,40,D3,80,00,00,00,00,00
BE,EF,03,06,00,10,DB,65,00,00,00,00,00
BE,EF,03,06,00,23,DB,66,00,00,00,00,00
BE,EF,03,06,00,0D,DA,68,00,01,00,00,01
BE,EF,03,06,00,0D,DA,68,00,02,00,00,02
BE,EF,03,06,00,0D,DA,68,00,02,00,00,04
BE,EF,03,06,00,0D,DA,68,00,02,00,00,00
BE,EF,02,06,00,DF,DF,66,00,01,00,00,01
BE,EF,02,06,00,DF,DF,66,00,02,00,00,02
BE,EF,02,06,00,02,D0,2B,00,01,00,00,01
BE,EF,02,06,00,02,D0,2B,00,02,00,00,02
BE,EF,02,06,00,F1,DE,68,00,00,00,00,00
BE,EF,02,06,00,20,DF,69,00,00,00,00,00
BE,EF,02,06,00,0E,DE,67,00,01,00,00,01
BE,EF,02,06,00,0E,DE,67,00,02,00,00,02
BE,EF,03,06,00,89,DB,6C,00,00,00,00,00
BE,EF,03,06,00,58,DA,6D,00,00,00,00,00
BE,EF,02,06,00,86,D1,2F,00,00,00,00,00
BE,EF,03,06,00,6B,DA,6E,00,00,00,00,00
BE,EF,03,06,00,D5,D9,70,00,00,00,00,00
BE,EF,03,06,00,04,D8,71,00,00,00,00,00
BE,EF,02,06,00,54,EF,7C,00,01,00,00,01
BE,EF,02,06,00,54,EF,7C,00,00,00,00,00
BE,EF,02,06,00,54,EF,7C,00,01,00,00,02
BE,EF,02,06,00,54,EF,7C,00,01,00,00,03
BE,EF,02,06,00,54,EF,7C,00,01,00,00,04
BE,EF,02,06,00,54,EF,7C,00,01,00,00,05
Auto Sync
Factory default
Firmware version
System Status
3D Sync
3D Sync on
3D Sync off
Top-Bottom
Frame Sequential
Frame Packing
Side-By-Side
70
Color mode
Brightest
PC
Movie
ViewMatch
White Board
Black Board
Green Board
User 1
User 2
English
Nederlands
BE,EF,03,06,00,38,5A,88,12,08,08,12,08
BE,EF,03,06,00,38,5A,88,10,00,00,10,00
BE,EF,03,06,00,38,5A,88,13,01,01,13,01
BE,EF,03,06,00,38,5A,88,14,02,02,14,02
BE,EF,03,06,00,38,5A,88,15,05,05,15,05
BE,EF,03,06,00,38,5A,88,16,06,06,16,06
BE,EF,03,06,00,38,5A,88,17,07,07,17,07
BE,EF,03,06,00,38,5A,88,18,03,03,18,03
BE,EF,03,06,00,38,5A,88,19,04,04,19,04
BE,EF,1A,0C,00,09,0B,3A,00,01,00,00,01
BE,EF,1A,0C,00,09,0B,3A,00,02,00,00,02
BE,EF,1A,0C,00,09,0B,3A,00,03,00,00,03
BE,EF,1A,0C,00,09,0B,3A,00,04,00,00,04
BE,EF,1A,0C,00,09,0B,3A,00,05,00,00,05
BE,EF,1A,0C,00,09,0B,3A,00,06,00,00,06
BE,EF,1A,0C,00,09,0B,3A,00,07,00,00,07
BE,EF,1A,0C,00,09,0B,3A,00,08,00,00,08
BE,EF,1A,0C,00,09,0B,3A,00,09,00,00,09
BE,EF,1A,0C,00,09,0B,3A,00,0A,00,00,0A
BE,EF,1A,0C,00,09,0B,3A,00,0B,00,00,0B
BE,EF,1A,0C,00,09,0B,3A,00,0C,00,00,0C
BE,EF,1A,0C,00,09,0B,3A,00,0D,00,00,0D
BE,EF,1A,0C,00,09,0B,3A,00,0E,00,00,0E
BE,EF,1A,0C,00,09,0B,3A,00,0F,00,00,0F
BE,EF,1A,0C,00,09,0B,3A,00,10,00,00,10
BE,EF,1A,0C,00,09,0B,3A,00,11,00,00,11
BE,EF,1A,0C,00,09,0B,3A,00,12,00,00,12
BE,EF,1A,0C,00,09,0B,3A,00,13,00,00,13
BE,EF,1A,0C,00,09,0B,3A,00,14,00,00,14
BE,EF,02,06,00,22,55,76,00,00,00,00,01
BE,EF,02,06,00,22,55,76,00,00,00,00,00
BE,EF,02,06,00,40,B5,86,00,00,00,00,01
BE,EF,02,06,00,40,B5,86,00,00,00,00,00
BE,EF,02,06,00,D3,D1,2A,00,00,00,00,01
BE,EF,03,06,00,EE,DA,6B,00,00,00,00,01
BE,EF,10,05,00,C6,FF,11,11,01,00,01,01
BE,EF,03,06,00,DC,DB,69,69,00,00,69,00
Italiano
Language
Deutsch
Svenska
Suomi
Polski
Indonesia
Magnify
Green Mode
Dynamic Mode
Quick Power Off
Magnify Inc
Magnify Dec
Green Mode On
Green Mode Off
Dynamic Mode On
Dynamic Mode Off
QuickPowerOff_On
QuickPowerOff_Off
71
IR Control Code
System Code: 83F4
Format : NEC
17
08
45
41
52
40
10
0b
0e
15
0f
0c
56
30
36
72
28
06
37
05
31
18
82
8E
03
83
55
07
14
2B
27
13
Key
Power
Auto Sync
VGA1
VGA2
Video
Source
Color Mode
Enter
Up / Keystne+
Down / KeystoneLeft
Right
Menu
My Button(Function)
Exit
Mouse
Mouse left
Mouse right
Mouse Page Up
Mouse Page Down
Lock(Key pad)
Pattern
D.Eco
(Dynamic Eco)
Magnify +
Freeze
Blank
Timer (Presentation)
Volume+
VolumeMute
Aspect
Format
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
Byte1
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
Byte2
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
Byte3
17
08
41
45
52
40
10
15
0b
0c
0e
0f
30
56
28
31
36
37
06
05
8E
55
2B
Byte4
E8
f7
be
ba
ad
bf
ef
ea
f4
f3
f1
f0
CF
A9
D7
CE
C9
C8
F9
FA
71
AA
D4
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
18
03
07
27
82
83
14
13
e7
fc
f8
d8
7D
7C
eb
EC
73
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T = Telephone
Email
F = FAX
AUS= 1800 880 818
Australia/New Zealand
www.viewsonic.com.au
service@au.viewsonic.com
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
Canada
www.viewsonic.com
T (Toll)= 1-424-233-2533
service.ca@viewsonic.com
F= 1-909-468-3757
Europe
www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong
www.hk.viewsonic.com
T= 852 3102 2900
service@hk.viewsonic.com
India
www.in.viewsonic.com
T= 1800 266 0101
service@in.viewsonic.com
Korea
www.kr.viewsonic.com
T= 080 333 2131
service@kr.viewsonic.com
Latin America (Argentina) www.viewsonic.com/la/
T= 0800-4441185
soporte@viewsonic.com
Latin America (Chile)
www.viewsonic.com/la/
T= 1230-020-7975
soporte@viewsonic.com
Latin America
www.viewsonic.com/la/
T= 01800-9-157235
soporte@viewsonic.com
(Columbia)
Latin America (Mexico)
www.viewsonic.com/la/
T= 001-8882328722
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
www.viewsonic.com/la/
T= 0800-54565
soporte@viewsonic.com
Macau
www.hk.viewsonic.com
T= 853 2870 0303
service@hk.viewsonic.com
Middle East
ap.viewsonic.com/me/
Contact your reseller
service@ap.viewsonic.com
T= 1-800-688-6688 (English)
service.us@viewsonic.com
Puerto Rico & Virgin
www.viewsonic.com
T= 1-866-379-1304 (Spanish)
Islands
soporte@viewsonic.com
F= 1-909-468-3757
Singapore/Malaysia/
www.viewsonic.com.sg
T= 65 6461 6044
service@sg.viewsonic.com
Thailand
South Africa
ap.viewsonic.com/za/
Contact your reseller
service@ap.viewsonic.com
T (Toll-Free)= 1-800-688-6688
United States
www.viewsonic.com
T (Toll)= 1-424-233-2530
service.us@viewsonic.com
F= 1-909-468-3757
Country/Region
Website
74
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
for labor, and one (1) year for the original lamp from the date of the first consumer
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
original lamp from the date of the first consumer purchase; Europe: One (1) year
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1.Any product on which the serial number has been defaced, modified or removed.
2.Damage, deterioration, failure, or malfunction resulting from:
a.Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,
improper maintenance, unauthorized product modification, or failure to follow
instructions supplied with the product.
b.Operation outside of product specifications.
c.Operation of the product for other than the normal intended use or not under
normal conditions.
d.Repair or attempted repair by anyone not authorized by ViewSonic.
e.Any damage of the product due to shipment.
f. Removal or installation of the product.
g.Causes external to the product, such as electric power fluctuations or failure.
h.Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3.Removal, installation, and set-up service charges.
75
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and fitness for a
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
This warranty gives you specific legal rights, and you may also have other rights
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
76
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a.Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, unauthorized attempted repair, or failure to follow instructions supplied with the
product.
b.Any damage of the product due to shipment.
c.Causes external to the product, such as electrical power fluctuations or failure.
d.Use of supplies or parts not meeting ViewSonic’s specifications.
e.Normal wear and tear.
f.Any other cause which does not relate to a product defect.
3.Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4.Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1.To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2.Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1.Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity,
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2.Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
77
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within
Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA
de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de
C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English);
866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
78
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising