softstarters
Motors | Energy | Automation | Coatings
Automation
Soft-Starters
www.weg.net
2
Soft-Starters
www.weg.net
Soft-Starters
Soft-Starters are static starters that accelerate,
decelerate and protect three-phase induction motors.
The control of the voltage applied to the motor by means
of adjustments to the firing angle of thyristors allows the
soft-starter to start and stop an electric motor smoothly.
With adequate adjustments of the variables, the torque
produced is adjusted to the needs of the load, so that the
required current is going to be the lowest possible for the
starting procedure.
WEG Soft-Starters are micro processed, fully digital,
state-of-the-art technology products designed to ensure
the best starting and stopping performance of induction
motors, presenting itself as a complete and low-cost solution.
The human-machine interface allows easy adjustment of the
parameters which helps set up and operation.
The soft-starter line is top-notch in motor starting and
stopping with features that allow the starting, stopping and
protection of electric motors in an easy and efficient manner.
Comparison of electric motor start-up methods
DIRECT ON LINE STARTER
WYE / DELTA
STARTING
Soft-Starters
3
www.weg.net
SSW-05
The SSW-05 Plus Micro Soft-Starters, with DSP control
(Digital Signal Processor) have been designed to supply
excellent performance during starting and stopping of
electric motors with an excellent cost/benefit ratio. The Operator Interface allows easy parameter setting,
simplifying the start-up and operation activities.
The SSW-05 Plus Micro Soft-Starters are compact,
optimizating the space in electrical panels.
The SSW-05 Plus already incorporates protection for the
driven motor.
Benefits
eduction of stress on couplings and other R
transmission devices during starting (gear boxes, sheaves).
g Extended lifetime of motor and mechanical
components due to reduced
mechanical stress.
g Easy operation, programming and maintenance.
g Simple electrical wiring.
g Operation in ambient up to 55°C (122°F).
g
Applications
Centrifugal
Pumps
Roller Tables
g Piston Compressors
g Mixers
g Fans
g
g
Certifications
4
Soft-Starters
www.weg.net
SSW-05 Wiring Diagram
Settings and Indications
Dip-switch to enable/disable the motor
protections
Three phase
power supply
LEDs to indicate fault trips
Electronic power supply
and digital inputs
LEDs to indicate the starter status
Potentiometers for pedestal voltage,
acceleration/deceleration time and
motor current settings.
Serial or remote
HMI connector
Relay outputs
Output to motor
Soft-Starters
5
www.weg.net
SSW-05 - Keypad
Remote Human-Machine Interface for remote operation on panel door or machine console. The HMI has a copy function
incorporated, allowing copying of parameters from a soft-starter to others, allowing fast reliable setting of identical starters.
Start the soft-starter
Stop the soft-starter. Resets the
soft-starter after a fault trip has
occurred
Scroll up parameters or
parameter value
Scroll down parameters or
parameter value
Parameter content
access/escape/enter
SUPERDRIVE Software
Windows-based software for setting
parameters, control and monitoring
SSW-05 Soft-Starters.
It allows setting parameters on-line
directly to the Soft-Starters and/or
setting of parameters off-line into a file.
Possibility to store user parameters
from existent SSW-05 Soft-Starters.
The communication between the
Soft-Starter and the computer is
provided through RS-232 serial
interface.
6
Soft-Starters
Model
Model
Ítem
CAB-RS-1
1m Cable for serial remote HMI
10050268
CAB-RS-2
2m Cable for serial remote HMI
10190951
CAB-RS-3
3m Cable for serial remote HMI
10211478
HMI-SSW05-RS
Remote HMI for CAB-RS cable up to 3m
10193351
www.weg.net
SSW-05 - Models
3 to 30 A
45 to 85 A
SSW-05 - Drive ratings
The tables below present the expected motor power for each soft-starter model under light load application (e.g.:
centrifugal pump). However, for the proper selection of soft-starters, please use the SDW software.
Use the motor power ratings below only as a guidance. Motor rated currents may vary with speed and manufacturer. IEC
motor powers are based on WEG 4-pole motors; NEMA motor powers are based on NEC table 430-150.
Motor voltages between 220V and 460V
IEC - 50Hz
Model
Output
Current
IEC - 60Hz
220V
230V
380V
415V
220V
230V
NEMA - 60Hz
440V
460V
230V
460V
A
kW
kW
HP
HP
HP
HP
SSW050003T2246
3
0.55
1.1
1
1.5
0.5
1.5
SSW050010T2246
10
2.2
4
3
7.5
3
5
SSW050016T2246
16
4
7.5
5
10
5
10
SSW050023T2246
23
5.5
11
7.5
15
7.5
15
SSW050030T2246
30
7.5
15
10
20
10
20
SSW050045T2246
45
11
22
15
30
15
30
SSW050060T2246
60
15
30
20
40
20
40
SSW050085T2246
85
22
45
30
60
30
60
Motor voltages between 525V and 575V
Model
IEC
NEMA
Output
Current
50Hz
525V
60Hz
575V
A
kW
HP
SSW050003T4657
3
1.5
2
SSW050010T4657
10
5.5
7.5
SSW050016T4657
16
9.2
10
SSW050023T4657
23
15
20
SSW050030T4657
30
18.5
25
SSW050045T4657
45
30
40
SSW050060T4657
60
37
50
SSW050085T4657
85
55
75
Soft-Starters
7
www.weg.net
SSW-05 - Dimensions and Weight
Dimensions
mm (in)
Frame
Size
Model
SSW050003T2246
SSW050010T2246
SSW050016T2246
SSW050023T2246
SSW050030T2246
SSW050045T2246
SSW050060T2246
SSW050085T2246
SSW050003T4657
SSW050010T4657
SSW050016T4657
SSW050023T4657
SSW050030T4657
SSW050045T4657
SSW050060T4657
SSW050085T4657
1
H
W
D
130
(5.12)
59
(2.32)
145
(5.71)
Weight
kg (lb)
185
(7.28)
79
(3.11)
172
(2.79)
1.67
(3.68)
1
130
(5.12)
59
(2.32)
145
(5.71)
0.74
(1.63)
185
(7.28)
79
(3.11)
172
(2.79)
Inside Delta
(6 cables)
Connection
Internal
Bypass
IP00
No
Yes
IP00
No
Yes
0.74
(1.63)
2
2
W
Degree of
Protection
H
1.67
(3.68)
D
Mechanical Mounting
Size
With L (mm) Height H
L
La
H
Depth P Mounting A Mounting B Mounting D
Mounting
(mm)
(mm)
(mm)
Ha (mm)
La
Weight
(Kg)
1
59
60,4 130 130,7
145
51
122
61
Bold M4/Rail 0.74
2
79
80,4 185 185,7
172
71
177
99
Bold M4/Rail 1.64
A
La, Ha, Mounting ( Only for setting with srew)
B
Ha
D
8
Soft-Starters
www.weg.net
SSW-05 - Technical Data
MODEL
Voltage
Power Supply
Starting Duty Cycle
Frequency
Electronic Supply
Cabiner Plastic
Method
CPU
Standard
Inputs
Digital
Outputs
Digital
Communication
Serial Interface
Safety
Protections
Functions
Starting Voltage
Programmable Acceleration Ramp
Programmable Deceleration Ramp
Motor Rated Current and
Soft-Starter Rated Current Ration
Temperature
Humidity
Enclosure
Control
Resources
Ambient
Altitude
Finishing
Installation
Conformities / Standards
Colour
Fastening
Safety
Low Voltage
EMC
SSW-05 Plus
220 - 460 Vac (+10%, -15%)
460 - 575 Vac (+10%, -15%)
50 / 60 Hz
Switched mode power supply (90 – 250 Vac )
IP00
Motor Voltage Variation
DSP Microcontroller
300% ( 3 x Inom. ) during 10 s, 4 starts per hour
01 input for starting and stopping
01 input for error reset
01 relay output for full voltage indication (By-Pass)
01 relay output for operation indication
RS-232C
Motor overload
Phase sequency
Phase loss
Locked rotor
SCRs overload
Overcurrent
Internal fault (watchdog)
30 - 80% of the rated voltage
1 – 20 s
Off – 20 s
30 - 100%
0 ... 55 ºC - standard operation at rated current
0 ... 90% non condensing
0 ... 1000 m (3,300 ft) - standard operation at rated current
1000...4000m - with current derating (1%/ 100 m (328 ft) above 1000m (13.300ft)
Frost gray (cover) and blue (base) WEG standard
Fastening by bolts or assembling on DIN 35 mm rail
UL 508 Standard – Industrial Control Equipment / IRAM
IEC 60947-4-2
EMC Directive 89 / 336 / EEC - Industrial Environment
Soft-Starters
9
www.weg.net
SSW-05 - Coding
SSW050010 T 2246 P P -1
2
3
4
5
6
7
-- Z
8
9
1 - Soft-Starter line SSW-05
2 - Rated output current: 0003 = 3 A
0010 = 10 A
0016 = 16 A
0023 = 23 A
0030 = 30 A
0045 = 45 A
0060 = 60 A
0085 = 85 A
3 - Input power supply voltage:
T= Three-phase
4 - power supply voltage:
2246 = 220 ... 460 V
4657 = 460 ... 575 V
5 - Product manual language:
P = Portuguese
E = English
S = Spanish
G = German
6 - Product version
P = Plus
7 - Special hardware
Blank = Standard (not available)
Hx = Optional version x (H1 ... Hn)
8 - Special software
Blank = Standard (not available)
Sx = Optional version x (S1 ... Sn)
9 - Code end
Z = Digit indicating code end
Ex.: SSW050060T4657PPZ
10
Soft-Starters
www.weg.net
SSW-06
WEG SSW-06 series soft-starters are micro-processor
controlled, fully digital and designed with state-of-the-art
technology.
Excellent acceleration and deceleration control is achieved
with an optimized cost to benefit ratio.
The HMI allows easy programming during commissioning
and operation. The built-in “Pump Control” function gives
optimized pre-set pump application parameters, avoiding
“Water Hammer”.
Benefits
32 Bits RISC high performance microcontroller;
Electronic motor protection;
g Removable Human Machine interface with double display
(LED/LCD);
g Fully programmable control methods;
g Totally flexible torque control;
g “Kick-start” function for high break-away torque
g “Pump control” function for intelligent control of pumping
systems;
g Avoids “water hammer” in pumps;
g Current peaks limits on the power supply;
g Voltage drop limits during starting;
g Voltage Range ( 220 to 575Vac and 575 to 690Vac);
g The control board power supply has EMC filter (94 to 253 Vac);
g Built-in bypass up 820A, providing size reduction and
saving;
g Back-up memory of motor protection I2t thermal image;
g Voltage and current unbalance protection;
g Over/under voltage and current protection;
Input for motor PTC;
Reduction of mechanical stress;
g Reduction of stress over couplings and transmission
devices (gearboxes, sheaves, belts, etc…);
g Increases the lifetime of the motor and mechanical
equipment of the driven machine;
g Easy operation, programming and maintenance via Keypad;
g Simplified electrical installation;
g Oriented start-up;
g Possibility for standard three leads or inside delta size
cable connection;
g All protections and function available for both types of
connection (unique in the market);
g Serial or fieldbus communication errors protection;
g Operational environment up to 55o C (without current
reduction). For model range 10A to 820A and up to 40oC
(without current reduction) for model range 950A to 1400A.
g International certifications such as IRAM, C-Tick, UL, cUL,
Gost and CE.
g
g
g
g
Soft-Starters
11
www.weg.net
SSW-06 - Applications
Chemical and Petrochemical
g
Fans / Exhaut fans
g
Centrifugal pumps
g
Dosing / Process pumps
g
Centrifugal pumps
g
Agitators / mixers
g
Compressors
g
Soap extruders
Sugar and Alcohol
Fans / Exhaut fans
g
Process pumps
g
Conveyor belts
g
Food and Ration
Dosing / Process pumps
g
Fans / Exhaut fans
g
Agitators / Mixers
g
Dryers / Furnaces
g
Pellet mills
g
Hoist / Monorails
g
Ceramic
Fans / Exhaut fans
g
Dryers / Furnaces
g
Ball mills
g
Roller tables
g
Converyor belts
g
Wood
Slicing Machine
g
Polishing Machine
g
Cutting machines
g
Wood chippers
g
Saw and plains
g
12
Soft-Starters
Plastic and Rubber
E xtruding machines
g Blow Molding
g
Mixers
g
Calenders
g
Grinders
g
Juice and Beverages
Centrifagal pumps
g
Agitators / Mixers
g
Roller tables
g
Conveyor belts
g
Bottling lines
Pulp and Paper
Dosing pumps
g
Process pumps
g
Fans / Exhaust fans
g
Agitators / Mixers
g
Rotatory filters
g
Rotatory kilns
g
Scrap conveyor
g
Papers refiners
g
Cement and Mining
Dosing / Process pumps
g
Sifting Machines / Rotating tables
g
Dynamic graders
g
Conveyor belts
g
g
Textile
Agitators / Mixers
g
Dryers / washing machines
g
g
Glasses
Fans / Exhaut fans
g
Bottle manufactoring machine
g
Roller tables
g
Converyor belts
Siderurgy and Metallurgy
Fans / Exhaust fans
g
Conveyor belt
g
Drilling & Grinding machines
g
Pumps
Refrigeration
Process pumps
g
Fans / Exhaut fans
g
Compressors
g
g
Waste water treatment
A xial flow pumps
g
Impulsion systems
g
g
Load transportation
Conveyors / Belts / Chains
g
Roller tables
g
Monorails / Hoist
g
Escalators
g
Baggage conveyors (airports)
www.weg.net
Voltage and current protections
Under and Over Voltage
It allows adjustment of the
limits for under and over
voltage protection. It is
available in both types of
connections to the motor.
Voltage
Over
Voltage
Over voltage
Rated
Over
Under
Under voltage
Current
Under and Over Current
It allows adjustment of the
limits for under and over
current protection.
Over
Rated
Under
Current
Over current
Over
Rated
Under
Rated
Under
Under current
by-pass built-in
Built-in by-pass reduces power and heating losses in the
thyristors, providing size reduction and energy saving.
It is available in the models from 10A up to 820A.
Three
phase
power
supply
Three
phase
motor
Soft-Starters
13
www.weg.net
SSW-06 - Main Functions
Voltage Ramp
It provides smooth acceleration and / or deceleration by
using voltage ramps.
Current Ramp
It allows to adjust the current limitation for the beginning of
the start. Applicable to load with higher or lower initial torque.
Voltage
Current
Deceleration
Acceleration
Current limitation
Rated current
Voltage ramp or pump control
Pump Control
Pump control provides a smooth deceleration avoiding
“overshoots”.
Fixed current limitation
Current
Current
Current limitation
Rated current
Current limitation
Rated current
Fixed current limitation
Fixed current limitation
Current Limitation
It allows the torque limitation adjustment during the starting
procedure based on application requirements.
Current
Current limitation
Torque Control
The SSW-06 has a torque control algorithm with high
performance and total flexibility for any application
requirements.
It is available in both types of connection to the motor
(standard / within the delta of the motor).
1 adjustment point - Constant torque.
2 adjustment points - Linear torque ramp.
g 3 adjustment points - Quadratic torque ramp.
g
g
Rated current
Fixed current limitation
Voltage and current Kick Starter
It provides an initial pulse of voltage or current that when
applied in the motor provides an additional initial torque to
the start the motor. Required for loads with high initial torque.
Torque
Constant torque
Rated torque
Torque control with one point
Torque
Voltage
Voltage kick starter
Rated voltage
Linear torque
Rated torque
Voltage ramp
Torque control with two points
Torque
Current
Rated torque
Rated current
Current limitation
14
Soft-Starters
Quadratic torque
Torque control with three points
www.weg.net
SSW-06 - Keypad (HMI)
Intelligent Interface
Intelligent operation interface with double display, LED (7 segments) and LCD (2 lines of 16 characters), which allows excellent
long distance visibility, with a detailed description of all parameters and messages via alphanumeric LCD display.
Selectable Language
Intelligent operation interface allows the user to choose the language to be used for programming and display of parameters
and messages in the LCD display.
The high level of hardware and software capacity of the product offers the user many options of language such as:
Portuguese, English, German and Spanish, in order to adapt to any user in the world.
LED display
(7 segments)
LCD display
Changes the display between the
parameter number and its value
(position/content).
Increases the parameters
number or its value.
It enables the motor (start).
Decreases the parameter
number or its value.
It disables the motor (stop). Also resets the
soft-starter after a fault has occurred.
LOCAL led
It reverses the rotation
direction (please verify
availability).
REMOTE led
CLOCKWISE led
COUNTER
CLOCKWISE led
It selects if the controls / reference will be received
locally in the HMI (LOC) or remotely (REM)
JOG function (Please check if available).
Copy Function
The intelligent interface also offers the “COPY” function that allows copying the parameters of a soft-starter to another,
bringing speed, reliability and programming repetition to similar applications.
SSW-06
HMI
HMI
SSW-06
Soft-Starter “A”
Soft-Starter “B”
Oriented Start-Up
Soft-starters are equipment intended to start induction motors, where adaptation and response are directly related to the
motor characteristics as well as the power supply.
The soft-starters from SSW-06 series have a programming option specially developed to simplify the start-up, by an oriented
and automatic sequence that guides the user to the sequential programming of the minimum characteristics required for
adaptation of the soft-starter to the driven motor and load.
Soft-Starters
15
www.weg.net
SSW-06 - Fieldbus Communication
The SSW-06 soft-starters can be communicated to fieldbus communication network through the most common standard
protocols in the world, as it follows:
FIELDBUS PROFIBUS DP (optional)
DeviceNet (optional)
g Modbus RTU (software embedded)
g Modbus RTU RS-485 (optional)
g EtherNet / IP ( optional)
g
g
Mainly intended to integrate large automation plants, communication networks offer many advantages in the supervision,
monitoring and on-line control of the soft-starters, providing high performance and great operational flexibility.
To be connected to communication protocols, as Profibus DP, DeviceNet and EtherNet IP, optional modules need to be fitted
in the SoftStarter. For connecting the SSW-06 to Modbus RTU network the RS-232 or RS-485 adapter can be used.
Besides providing protection, monitoring and motor control, it is allowable the use of digital and analog I/Os of the SSW-06 as
a remote unit in a profibus DP network.
PLC
FIELDBUS NETWORK
...
16
Soft-Starters
www.weg.net
SSW-06 - Superdrive G2
Windows-based Software, for SSW-06 programming, control
and monitoring.
g Automatic SSW-06 identification.
g Reads SSW-06 parameters.
g Writes SSW-06 parameters.
g Online parameters settings.
g Offline parameters settings allow an user application to
be created.
g Allows documentation of the application to be created.
g Easily accessible.
g The TRACE FUNCTION provided with Superdrive G2 version, through waveforms gives the user the possibility of status of the Soft Starter at normal operating conditions as well as for troubleshooting.
g A 2m shielded USB cable is provided with the product.
g Online help.
g Free software on the site www.weg.net
Monitoring and parameterization of the list of parameters comparison
to factory default easy
Integrated Environment
Monitoring and control window
using virtual HMI
Trace function configuration in the G2 superdrive
Status monitoring
Soft-Starters
17
www.weg.net
SSW-06 - SOFTPLC Function
A resource that provides PLC functions in the SSW-06 giving
flexibility to the user and allowing development of
customized user application programs.
LADDER programming language – WLP Software.
Access to all inverter parameters and I/Os.
g PLC, mathematical and control blocks.
g Download, upload and online monitoring.
g Memory capacity of 1kbytes.
g Allows documentation of the application to be created.
g Online help.
g Free software on the site www.weg.net
g
g
On-line monitoring
Simple and practical progranming enviromment
User’s parameters
Digital input and output monitoring
18
Soft-Starters
Virtual HMI for alteration of parameters
www.weg.net
SSW-06 - Accessories and Options
Operation interface with double display
LED and LCD, with COPY function, for local installation
(in the cover of the soft-starter) or remotely in the door of a
panel. Maximum distance 5 m (without frame).
Installation frame / human-machine interface
Remote mounting of the HMI to the door of a panel or to a
machine console. Maximum distance 5 m.
Cable length for HMI and SSW-06
Cable length (X) 1, 2, 3 and 5 m.
Fieldbus Cards
These cards enable SSW06 control via fieldbus.
RS-485 communication kit
Enables the connection of the SSW06
to a Modbus-RTU fieldbus via an isolated RS485.
COMPLETE HUMAN-MACHINE INTERFACE (standard)
REMOTE INTERFACE FRAME KIT KMR – SSW-06
REMOTE INTERFACE
INTERCONNECTION CABLES
CAB – HMI SSW-06-X
FIELDBUS Communication Kits
Profibus DP → KFB-PD
DeviceNet → KFB-DN
Profibus DPV1 → KFB-PDPV1
DeviceNet Acyclic → KFB-DD
EtherNet /IP → KFB-ENIP
Communication Kit RS-485
RS-485 → KRS-485
POWER CONNECTION TERMINALS PROTECTION KIT
(for models from 85A up to 820A)
IP 20 Kit
Protection of the power terminal blocks
USB Kit
It allows communication with a PC via USB port
I/O Expansion Kit
6 Isolated Digital Inputs and Outputs to use with
SOFTPLC.
External Current Acquisition Kit
To be used when external By-Pass is required to keep
protections activated.
KIT IP20-M2 (85A to 130A)
KIT IP20-M3 (170A to 205A)
KIT IP20-M4 (255A to 365A)
KIT IP20-M5 (412A to 604A)
KIT IP20-M6 (670A to 820A)
Communication Kit
Digital I/Os Expansion
Current Acquisition Kit
K-ECA
(for models 255A to 1400A)
Soft-Starters
19
www.weg.net
SSW-06 - A complete, flexible and compact product
Power supply incoming –
Power input terminals
Removable HMI with double
display (LCD + LED),
multi-language and
COPY function
LED display 7
segments
Liquid crystal (LCD) display
2 lines of 16 characters
32 Bits RISC high
performance
microcontroller
Network communication
modules to: Profibus DP,
DeviceNet (both optional)
Three programmable
digital relay outputs
Motor PTC
insulated input
Interface serial RS-485
Modbus-RTU (optional)
Six insulated programmable
digital inputs
Interface serial RS-232
Modbus-RTU
Control
cables access
Power output terminals to
the motor
Two programmable
analogue outputs
20
Soft-Starters
Electronic board
protection fuse
www.weg.net
SSW-06 -Typical Wiring Diagrams
Standard (3 leads)
Inside Delta Connection (6 leads)
SSW-06 Standard Connection
Motor in Y
SSW-06 Delta Connected
Motor in
ISoft-Starter= IFull Current
ISoft-Starter= Irequired
√3
= 58% of Irequired
ISoft-Starter= Irequired
1,5
= 67% of Irequired
(after the start)
(during start)
Notes
g At the Starting, for the same motor power, the Inside Delta connection (6leads) allows for a reduction of 33% of the Soft Starter current if compared to the 3 leads connection. Even when the motor is up to speed a reduction of 43% of the Soft Starter current is achieved by using 6 leads connection. Basically the Inside Delta connection option offered by the SSW-06 gives the costumer alernative ways of reducing cost and size when it comes to Soft Starter solutions.
g A 6 leads motor is required when Inside Delta Connection is used.
MOTOR
220V -∆ / 380V-Y
380V -∆ / 660V-Y
440V -∆ / 760V-Y
575V - ∆
220V -∆ / 380V- Y/
440V -∆ / 760V-Y
6 leads connection
220V -∆
380V -∆
440V -∆
575V -∆
220V -∆
440V -∆
or the same motor power, the connection within the Delta Inside Connection’ ( 6 leads), a reduction of 42% of the softF
starter current compared to the standard connection (3 leads).
g The connection within the delta of the motor (6 leads) allows the soft-starter to start a motor 73% greater than the standard
connection (3 leads).
g The connection within the delta of the motor requires 6 leads from the soft-starter to the motor.
g During the start, the motor current can be 1.5 times greater than the soft-starter one.
g After the start, the motor current can be 1.73 times greater than the soft-starter.
g
Soft-Starters
21
www.weg.net
SSW-06 - Drive Ratings
The tables below present the expected motor power for each soft-starter model under light load application (e.g.: centrifugal
pump). However, for the proper selection of soft-starters, please use the SDW software.
Use the motor power ratings below only as a guidance. Motor rated currents may vary with speed and manufacturer. IEC
motor powers are based on WEG 4-pole motors; NEMA motor powers are based on NEC table 430-150 (ratings up to 500 HP)
and on WEG 4-pole motors (ratings above 500 HP).
Inline (3 leads) connection
Motor voltages between 220V and 575V
Model
SSW060010T2257
SSW060016T2257
SSW060023T2257
SSW060030T2257
SSW060045T2257
SSW060060T2257
SSW060085T2257
SSW060130T2257
SSW060170T2257
SSW060205T2257
SSW060255T2257
SSW060312T2257
SSW060365T2257
SSW060412T2257
SSW060480T2257
SSW060604T2257
SSW060670T2257
SSW060820T2257
SSW060950T2257
SSW061100T2257
SSW061400T2257
Output
Current
A
10
16
23
30
45
60
85
130
170
205
255
312
365
412
480
604
670
820
950
1100
1400
220V
230V
kW
2.2
4
5.5
7.5
11
15
22
37
45
55
75
90
110
110
132
185
200
250
280
315
400
IEC - 50Hz
380V
525V
415V
kW
kW
4
5.5
7.5
9.2
11
15
15
18.5
22
30
30
37
45
55
55
90
90
110
110
132
132
185
160
220
185
250
220
300
250
355
315
450
355
500
450
560
500
710
560
800
710
1000
Motor voltage 690V
IEC - 60Hz
220V
440V
230V
460V
HP
HP
3
7.5
5
10
7.5
15
10
20
15
30
20
40
30
60
50
100
60
125
75
150
100
200
125
250
150
300
150
350
200
400
250
500
270
550
350
700
400
800
450
900
550
1250
NEMA - 60Hz
230V
460V
575V
HP
3
5
7.5
10
15
20
30
50
60
75
100
125
150
150
200
250
-
HP
5
10
15
20
30
40
60
100
125
150
200
250
300
300
400
500
600
700
800
900
1100
HP
7.5
10
20
25
40
50
75
125
150
200
250
300
350
450
500
600
700
900
1000
1100
1500
Model
SSW060045T5769
SSW060060T5769
SSW060085T5769
SSW060130T5769
SSW060170T5769
SSW060205T5769
SSW060255T5769
SSW060312T5769
SSW060365T5769
SSW060412T5769
SSW060480T5769
SSW060604T5769
SSW060670T5769
SSW060820T5769
SSW060950T5769
SSW061100T5769
SSW061400T5769
Output
Current
A
45
60
85
130
170
205
255
312
365
412
480
604
670
820
950
1100
1400
IEC
50Hz
690V
kW
37
55
75
110
160
185
250
300
355
400
450
560
630
800
900
1120
1400
NOTES:
1- The maximum power of the motors in the table have been calculated based on WEG 2 and 4 poles motors.
For motors with another polarity (Ex.: 6 or 8 poles), or another voltage (Ex.: 230, 400 or 460 V) and/or another supplier, please specify the soft-starter based on the motor rated current.
2 - In 950 A model, the fan voltage must be specified as 110 or 220 Vac.
3 - In 10A and 1400A models, the fan voltage is always 220 Vac.
4 – Ambient temperature (Ta) = 0… 55 C is only valid for 10A up to 820A models, for the 950A, 110A and 1400A models , Ta= 0… 40 C
22
Soft-Starters
www.weg.net
SSW-06 - Drive Ratings
Inside Delta (6 leads) connection
Motor voltages between 220V and 575V
IEC - 50Hz
Model
Output
Current
220V
230V
380V
415V
SSW060010T2257
SSW060016T2257
SSW060023T2257
SSW060030T2257
SSW060045T2257
SSW060060T2257
SSW060085T2257
SSW060130T2257
SSW060170T2257
SSW060205T2257
SSW060255T2257
SSW060312T2257
SSW060365T2257
SSW060412T2257
SSW060480T2257
SSW060604T2257
SSW060670T2257
SSW060820T2257
SSW060950T2257
SSW061100T2257
SSW061400T2257
A
77
103
147
225
294
355
441
540
631
713
831
1046
1160
1420
1645
1905
2424
kW
22
30
37
55
75
110
132
160
185
220
250
315
355
400
-
kW
37
55
75
110
160
185
220
250
315
370
450
560
630
800
900
1000
1250
IEC - 60Hz
NEMA - 60Hz
525V
220V
230V
440V
460V
230V
460V
575V
kW
55
75
90
160
220
250
315
400
450
500
630
800
900
1000
1250
1400
1800
HP
30
40
60
75
125
150
175
200
250
300
350
450
450
550
650
800
1000
HP
60
75
125
175
200
300
350
450
550
600
700
900
950
1250
1350
1500
2000
HP
25
30
50
75
100
125
150
200
250
-
HP
60
75
100
150
200
250
350
450
500
600
700
900
1000
1250
1350
1500
2000
HP
75
100
150
200
300
350
450
600
700
800
900
1100
1250
1500
1750
2000
2500
NOTES:
1- The maximum power of the motors in the table have been calculated based on WEG 2 and 4 poles motors.
For motors with another polarity (Ex.: 6 or 8 poles), or another voltage (Ex.: 230, 400 or 460 V) and/or another supplier, please specify the soft-starter based on the motor rated current.
2 - In 950 A model, the fan voltage must be specified as 110 or 220 Vac.
3 - In 10A and 1400A models, the fan voltage is always 220 Vac.
4 – Ambient temperature (Ta) = 0… 55 C is only valid for 10A up to 820A models, for the 950A, 110A and 1400A models , Ta= 0… 40 C
Soft-Starters
23
www.weg.net
SSW-06 - Dimensions and Weight
W
H
D
H
Dimensions
mm (in)
W
D
1
256
(10.08)
132
(5.20)
2
370
(14.57)
3
Weight
kg (lb)
Degree of
Protection
Inside Delta
(6 cables)
Connection
182
(7.16)
3.3
(7.3)
IP20
No
132
(5.20)
244
(9.61)
8.5
(18.7)
440
(17.32)
223
(8.78)
278
(10.94)
18.5
(40.8)
4
550
(21.65)
370
(14.57)
311
(12.24)
41.5
(91.5)
5
650
(25.59)
370
(14.57)
347
(13.66)
55
(121.3)
6
8
795
(31.30)
845
(33.27)
1147
(45.16)
540
(21.26)
570
(22.44)
685
(26.97)
357
(14.05)
347
(13.66)
432
(17.01)
120
(264.6)
107
(235.9)
217.5
(479.5)
2
370
(14.57)
132
(5.20)
244
(9.61)
8.5
(18.7)
3
440
(17.32)
223
(8.78)
278
(10.94)
18.5
(40.8)
4
550
(21.65)
370
(14.57)
311
(12.24)
41.5
(91.5)
5
650
(25.59)
370
(14.57)
347
(13.66)
55
(121.3)
6
795
(31.30)
845
(33.27)
1147
(45.16)
540
(21.26)
570
(22.44)
685
(26.97)
357
(14.05)
347
(13.66)
432
(17.01)
120
(264.6)
107
(235.9)
217.5
(479.5)
Frame
Size
Model
SSW060010T2257
SSW060016T2257
SSW060023T2257
SSW060030T2257
SSW060045T2257
SSW060060T2257
SSW060085T2257
SSW060130T2257
SSW060170T2257
SSW060205T2257
SSW060255T2257
SSW060312T2257
SSW060365T2257
SSW060412T2257
SSW060480T2257
SSW060604T2257
SSW060670T2257
SSW060820T2257
SSW060950T2257
SSW061100T2257
SSW061400T2257
SSW060045T5769
SSW060060T5769
SSW060085T5769
SSW060130T5769
SSW060170T5769
SSW060205T5769
SSW060255T5769
SSW060312T5769
SSW060365T5769
SSW060412T5769
SSW060480T5769
SSW060604T5769
SSW060670T5769
SSW060820T5769
SSW060950T5769
SSW061100T5769
SSW061400T5769
7
7
8
Internal
Bypass
Yes
IP00
(IP20 as
optional)
Yes
IP00
Yes
No
IP00
(IP20 as
optional)
No
Yes
IP00
No
No
Mechanical Mounting
Model
24
Soft-Starters
A
mm (in)
B
mm (in)
C
mm (in)
D
mm (in)
Fixation Bolt
Size
75
(2.95)
239
(9.40)
28
(1.10)
8,5
(0.33)
M5
1
75
(2.95)
350
(13.78)
28,5
(1.12)
8,5
(0.33)
M5
2
150
(5.91)
425
(16.73)
36,5
(1.44)
5,9
(0.23)
M6
3
200
(7.87)
527,5
(20.77)
85
(3.35)
10
(0.39)
M6
4
SSW060010
SSW060016
SSW060023
SSW060030
SSW060045
SSW060060
SSW060085
SSW060130
SSW060170
SSW060205
SSW060255
SSW060312
SSW060365
SSW060412
SSW060480
SSW060604
SSW060670
SSW060820
200
(7.87)
627,5
(24.70)
85
(3.35)
10
(0.39)
M6
5
350
(13.78)
775
(30.51)
95
(3.74)
7,5
(0.29)
M8
6
SSW060950
400
(15.75)
810
(31.89)
84
(3.31)
10
(0.39)
M8
7
SSW061100
SSW0601400
500
(19.68)
1110
(43.70)
93
(3.66)
15
(0.59)
M8
8
www.weg.net
SSW-06 - Mounting Clearance
A
Air flow
B
B
D
Input air flow
C
A
mm (in)
B
mm (in)
C
mm (in)
D
mm (in)
Size
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
1
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
2
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
3
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
4
150
(5.90)
30
(1.18)
150
(5.90)
150
(1.96)
5
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
6
SSW060950
150
(5.90)
30
(1.18)
150
(5.90)
50
(1.96)
7
SSW061100
SSW0601400
150
(5.90)
100
(1.18)
150
(5.90)
50
(1.96)
8
MODEL
SSW060010
SSW060016
SSW060023
SSW060030
SSW060045
SSW060060
SSW060085
SSW060130
SSW060170
SSW060205
SSW060255
SSW060312
SSW060365
SSW060412
SSW060480
SSW060604
SSW060670
SSW060820
Size01 Size02 Size03
Size04
Size05
Size06
Size07
Size08
Soft-Starters
25
www.weg.net
SSW-06 - Technical Data
Power
Control
Power Supply
Degree of protection
Control
Fan
Frequency
Metallic cabinet
Control method
CPU
Types of control
Rated
Starting Duty cycles
(10 starts / hour)
Heavy
Inputs
Digital
Outputs
Relay
Analog
Safety
Protections
Functions/resources
Standard
26
Soft-Starters
(220 to 690) Vac (-15% to +10%)
(110 to 230) Vac (-15% to +10%), or (94 to 253) Vac
Models from 255 to 820 A: 115 Vac (104 to 127) Vac / 230 vac (207 to 253) Vac
Model 950 A: 115 Vac (103,5 to 122) Vac / 230 vac (207 to 243,8) Vac
Models from 1100 to 1400 A: 230 vac (207 to 243,8) Vac
(50 to 60) Hz (+/- 10%), or (45 to 66) Hz
IP20 for 10A up to 30A / IP 00 from 45A
Motor voltage variation (Three phase induction motor)
32 Bits RISC microcontroller
Voltage ramp
Current limitation
Current limitation ramp
Pump control
Torque control 1,2 or 3 points
300% (3 x I nom.) during 30 s for 3 cables connection and during 25 s for 6 cables connection
450% (4,5 X I nom.) during 30 s with 33% rated current reduction;
450 % ( 4,5 x I nom.) during 25 s for 6 cables connection
5 x 24 Vdc insulated programmable inputs
1 x 24 Vdc insulated programmable input for motor PTC
3 programmable outputs 250 V / 2 A: (2 x NA) + (1 x NO + NC – Fault)
1 Programmable output (11 bits) 0…10 Vdc
1 programmable output (11 bits) 0...20 mA or 4...20 mA
Over voltage
Power supply phase loss
Under voltage
Output phase loss (motor)
Voltage unbalance
Thyristor failure
Under current
CPU failure (watch dog)
Over current
Programming error
Current unbalance
Serial communication error
Overload (motor) – i²t
Self-check error
Thyristors over temperature
HMI-SSW06 communication error
Motor over temperature / PTC
Starting time expired
Phase sequence failure
Fieldbus communication error
External fault
Serial communication error
Open by-pass contact failure (1)
Under voltage in the electronic board
Closed by-pass contact failure (1)
Frequency out of range
Over current in the by-pass (1)
Under current before by-pass closing (1)
Removable human-machine interface with double display LED + LCD
Programming access password
HMI language selection: Portuguese, English, Spanish and German
Control type selection: Voltage ramp, current limitation, current
limitation ramp, pump control and torque control
Local/ Remote operation selection
Self-checking and fault auto-reset
Oriented start-up according to the control type
Standard connection or Inside delta connection (not available for 690V)
All protections and functions available in both types of connection to the motor
PUMP CONTROL function (protection against “water hummer” in pumps)
COPY function (Soft-starter -> HMI or HMI -> soft-starter)
Built-in by-pass for the models 85 to 820 A
Serial interface RS-232 with Modbus RTU protocol. RS-485 optional
Insulated input for motor PTC
Standard or user parameters reset (Brings back the standard or user values)
Special features: Running hours
Programmable over and undervoltage and voltage unbalance between phases
Programmable over and undercurrent and current unbalance between phases
Under and over current before by-pass
Programmable immediate over current
Programmable time for immediate over current
Programmable immediate under current
Programmable time for immediate under current
Programmable line nominal voltage
Fully programmable voltage ramp
Programmable current limitation
Programmable current ramp
Programmable pump control
Fully flexible torque control
Auto reset of the programmable thermal memory
Thermal class protection (motor overload) programmable from class 5 to 45.
www.weg.net
SSW-06 - Technical Data
Functions/resources
Optional
Controls
Human-Machine Interface
(HMI-SSW06-LCD)
Supervision (read)
Temperature
Environment Conditions
Humidity
Altitude
Finishing Painting
Color
Standards
Safety
Low voltage
EMC
UL (USA) / cUL
(Canadá)
CE (Europe)
IRAM (Argentina)
C-Tick (Australia)
Frame for remote HMI
Cable to interconnect the soft-starter with the remote HMI 1. 2, 3 and 5 m
Rs-485 communication kit
PROFIBUS-DP communication kit
Device Net communication kit
IP20 protection for the models from 45A up to 820 A
Start, stop, reset and parameterization (main functions programming)
Increase and decrease parameters and their values
Motor current (% Soft-starter I n)
Motor current (% Motor I n)
Motor current (A)
Line frequency (0…99.9 Hz)
Line voltage (0…999 V)
Output voltage (0…999 V)
Motor torque (% motor I n)
Load active power – (kW)
Load apparent power – (kVA)
Soft-starter status
Digital and analogue inputs and outputs status
Load Cos (φ) – (0.00 – 0.99)
Powered-up Time hours
Enabled hours Operating Time
Last four error codes memory
Soft-starter software version
kWh hours Monitoring
Analog output Monitoring
SoftPLC status
Storage of the 6 most recent faults and fault diagnostics
Motor thermal memory monitoring
Fieldbus Communication status
Operating status
0 to 55 C (Models from 85 to 820 A) standard operation at rated current
0 to 40 C (Models from 950 to 1400 A) standard operation at rated current
5...90 %, non condensation
0... 1000 m: standard operation at rated current
1000... 4000 m; with output current reduction of 1%/100 m, over 1000 m
Cover: opaque gray
Cabinet: opaque blue
UL 508 Standard – Industrial control equipment (2)
EN 60947-4-2 Standard; LVD 73/23/EEC – Low voltage directive
EMC directive 89 / 336 / EEC – Industrial environment
Underwritters Laboratories Inc. – USA (2)
Certified by EPCOS
Instituto Argentino de Normalización (2)
Australian Communications Authority
Notes: (1) Models from 85A up to 820A
(2) Models from 85A up to 1400A approved, models from 10A up to 60A pending
Soft-Starters
27
www.weg.net
SSW-06 - Coding
SSW06 0085 T
1
2
3
22XX
P
O
_
_ SI
_
Z
4
5
6
7
8
10
11
9
1 - WEG soft-starter SSW-06 series
2 - Soft-starter rated output current
3 - Power supply: 0010 = 10A
0016 = 16A
0023 = 23A
0030 = 30A
0045 = 45A
0060 = 60A
0085 = 85A
00130 = 130A
00170 = 170A
0205 = 205A
0255 = 255A
0312 = 312A
0365 = 365A
0412 = 412A
0480 = 480A
0604 = 604A
0670 = 670A
0820 = 820A
0950 = 950A
1100 = 1100A
1400 = 1400A
T= three-phase
4 - Power supply voltage: 2257 = 220… 575 V
5769 = 575... 690V
5 - Manual language: P = Portuguese
E = English
S = Spanish
6 -Product version: S = standard
0 = With options
7 - Degree of protection (IP): 8 - Human-Machine interface (HMI): 9 - Special hardware: Blank = Standard (see technical data table)
Blank = Standard (with LED + LCD HMI)
SI = Without HMI
Blank = Standard
H1 = Fan 115V (950A model)
H2 = Fan 220V (950A up to 1400A model)
10 - Special software:
11 - Code end:
Blank = Standard
S1 = optional with special sofware version
Z = Product final codification indication digit
NOTE:
1 - Communication kits are optional
2 - From 950A up to 1400A models the ventilation voltage must be defined (H1 or H2)
28
Soft-Starters
www.weg.net
SSW-07 and SSW-08
The SSW-07 and SSW-08, with DSP (Digital Signal
Processor) control were designed for high performance on
motor starts and stops with an excellent cost-benefit ratio.
Easy to set up, it simplifies start-up activities and daily
operation.
The SSW-07 and SSW-08 are compact optimizing space in
electric panels.
It already incorporates electric motor protection. It adapts to
customer needs through its easy-to-install optional
accessories. Thus, a keypad and a
communication interface or a motor
PTC input can be added to the
product.
The new models of Soft Starter SSW07 and SSW-08 series has been
developed on the matter of achieving
the best cost-benefit ratio. The by-pass
built-in allows energy saving as well as
increased Soft Starter lifetime.
The SSW-07 and SSW-08 are equiped
with the same functionalities, being the
SSW07 applied for heavy load starts
and the SSW-08 for light and moderate
load starts.
Benefits
Applications
Reduction of mechanical stresses over the
coupling and transmission devices (gearboxes,
pulleys, gears, conveyors, etc) during the start;
g Increases motor and machine mechanical
equipment lifetime due to the reduction of
mechanical stress;
g Easy operation, setup and maintenance;
g Simple electrical installation;
g Operates in environments up to 55 °C (without
current reduction for all models);
g Integral, electronic motor protection;
g “Kick-Start” function for starting high
breakaway torque loads;
g Reduces “Water Hammer” in pump
applications;
g Limitation of voltage drop during start;
g Voltage Range ( 220 to 575Vac);
g Switched mode power supply with EMC filter
for the control of electronics (110 to 240 Vac);
g Built-in by-pass providing size reduction and
energy saving;
g Voltage monitoring of the electronics allows to
back-up I x t values (thermal image).
Typical Example of light and moderate loads
g Centrifugal Pump
g Immersed Centrifugal Pump
g Blade Vacuum Pump
g Screw Compressor
g Paper Refiner
g Sieving Machine
g Misturer
g
Typical Example of heavy loads
Stone Crusher
g Centrifugue
g Wood Chipper
g Wood Slicing machine
g Conveyor
g Axial and Centrifugal Fan
g Ball Mill (Ceramic)
g Hammer Mill
g
Soft-Starters
29
www.weg.net
SSW-07 and SSW-08 Wiring Diagram
SSW-07 / SSW-08
Applications
Connections, settings and indications
Power Supply input
DIP Switch to set and
enable the protections
Setting trimpots
DIP Switch for thermal
class setting
SSW-07 status
indication LEDs
Reset button
Lid for optional Plug-ins
Electronic power
supply (A1 and A2)
Relay output
Motor start / stop and
Reset digital inputs
Motor output
SSW-07 and SSW-08 - Accessories and Options
The SSW-07 and SSW-08 soft-starters can be communicated to fieldbus communication network through the most common
standard protocols in the world, as follows:
FIELDBUS PROFIBUS DP (with mfw01)
DeviceNet (optional)
g Modbus RTU RS-232 (optional)
g Modbus RTU RS-485 (optional)
g
g
Mainly intended to integrate large automation plants, communication networks offer
many advantages in the supervision, monitoring and on-line control of the soft-starters,
providing high performance and great operational flexibility.
TTo be connected to communication protocols, as Profibus DP and DeviceNet, the
SSW-07 and SSW-08 Series offer plug-in accessories to install according to the
desired protocol. For the Modbus RTU protocol, the connection can be done via RS232 or RS-485 (optional) interface.
30
Soft-Starters
PLC
“FIELDBUS” NETWORKS
www.weg.net
SSW-07 and SSW-08 - Keypad
Operation interface with display, LED
(7 segments), which allows excellent long
distance visibility. The HMI with “copy function”
built-in allows copy of certain user
configuration from an existent Soft Starter to
others. It gives reliability for applications where
the same parameters settings is desired for
more than one Soft Starter.
Local
Plug-in type HMI.
Remote
Remote HMI for placing at the panel
door or machinery console.
SSW-07 and SSW-08
local HMI
SSW-07 and SSW-08 remote HMI
Cable for connecting HMI to SSW-07 and SSW-08.
Cable length: 1,2,3,5,7.5 and 10m.
SUPERDRIVE G2
Windows-based Software, for SSW-07 and SSW-08 parameter setting, control and monitoring.
The following functionalities are provided with the Superdrive G2:
SSW-07 and SSW-08 automatic identification.
g SSW-07 and SSW-08 reading parameters
g Online parameters settings for SSW-07 and SSW-08
g Offline parameters settings to create a user application
g
Easily accessible.
upplied with a 3m RS-232 serial cable
S
when the Superdrive G2 software is
acquired.
g Free version available at WEG’s website
www.weg.net
g
g
SSW-07 and SSW-08 - Accessories and options
Modbus RTU – RS – 232
Optional Plug-in type module
for Mobus RTU communication in RS-232
Modbus RTU – RS – 485
Optional Plug-in type
module for Mobus RTU
communication in RS-485
IP20 Kit
For models from 130 A to
200 A, this kit guarantees
protection against contact
with energized parts.
Cable for connecting
RS-232. Cable length in 3
and 10m
DeviceNet
Optional Plug-in type
module for Devicenet
communication.
Motor PTC
Optional module for motor
PTC connection.
Profibus-DP
Via MFW-01/PD
Ventilation kit
For models from 45 A to
200 A. A ventilation kit is
necessary for heavy duty
starting cycle.
Soft-Starters
31
www.weg.net
Voltage
SSW-07 and SSW-08
Modes of Operation
Acceleration
Deceleration
Voltage ramp or Pump control
All settings necessary for starting any type of load is available
through trimpots and dip-switches.
Current
Voltage ramp
Allows smooth acceleration and/or deceleration, through
voltage ramps.
Current limit
Rated current
Current limit
Allows the setting of current limit during acceleration.
Fixed current limit
Voltage Kick Start
Voltage
It enables an initial voltage pulse which provides on initial
starting torque increase. This is required for starting high
breakway torque loads.
Voltage Kick start
Rated voltage
Voltage Ramp
Built-in by pass
Both SSW-07 and SSW-08 Series have built-in bypass to
minimizes power losses and heat dissipation in the thyristors,
providing size reduction and contributing to energy saving.
This is available in all models.
Three
phase
power
supply
Three
phase
motor
SSW-07 and SSW-08 - Drive Ratings
The tables below present the expected motor power for each soft-starter model under light load application (e.g.: centrifugal
pump). However, for the proper selection of soft-starters, please use the SDW software.
Use the motor power ratings below only as a guidance. Motor rated currents may vary with speed and manufacturer. IEC
motor powers are based on WEG 4-pole motors; NEMA motor powers are based on NEC table 430-150.
Motor voltages between 220V and 575V
Model
SSW070017T5
SSW070024T5
SSW070030T5
SSW070045T5
SSW070061T5
SSW070085T5
SSW070130T5
SSW070171T5
SSW070200T5
SSW080017T5
SSW080024T5
SSW080030T5
SSW080045T5
SSW080061T5
SSW080085T5
SSW080130T5
SSW080171T5
SSW080200T5
Output
Current
A
17
24
30
45
61
85
130
171
200
17
24
30
45
61
85
130
171
200
220V
230V
kW
4
5.5
7.5
11
15
22
37
45
55
4
5.5
7.5
11
15
22
37
45
55
IEC - 50Hz
380V
415V
kW
7.5
11
15
22
30
45
55
90
110
7.5
11
15
22
30
45
55
90
110
525V
kW
11
15
18.5
30
37
55
90
110
132
11
15
18.5
30
37
55
90
110
132
IEC - 60Hz
220V
440V
230V
460V
HP
HP
6
12.5
7.5
15
10
20
15
30
20
40
30
60
37
100
60
125
75
150
6
12.5
7.5
15
10
20
15
30
20
40
30
60
37
100
60
125
75
150
NEMA - 60Hz
230V
460V
575V
HP
5
7.5
10
15
20
30
50
60
75
5
7.5
10
15
20
30
50
60
75
HP
10
15
20
30
40
60
100
125
150
10
15
20
30
40
60
100
125
150
HP
15
20
25
40
50
75
125
150
200
15
20
25
40
50
75
125
150
200
NOTeS: The above maximum motor power ratings were calculated based on WEG models, 4 poles, IP55, standard, 55ºC ambient temperature.
32
Soft-Starters
www.weg.net
SSW-07 and SSW-08 - Dimensions and Weight
Model
Frame
Size
SSW070017T5
SSW070024T5
SSW070030T5
SSW070045T5
SSW070061T5
SSW070085T5
SSW070130T5
SSW070171T5
SSW070200T5
SSW080017T5
SSW080024T5
SSW080030T5
SSW080045T5
SSW080061T5
SSW080085T5
SSW080130T5
SSW080171T5
SSW080200T5
Dimensions
mm (in)
Weight
kg (lb)
H
W
D
1
162
(6.38)
95
(3.74)
157
(6.18)
1.3
(2.9)
2
208
(8.19)
144
(5.67)
203
(7.99)
3.3
(7.3)
3
276
(10.87)
223
(8.78)
220
(8.66)
7.6
(16.8)
1
162
(6.38)
95
(3.74)
157
(6.18)
1.3
(2.9)
Degree of
Protection
Inside Delta
(6 cables)
Connection
Internal
Bypass
No
Yes
No
Yes
IP20
IP00
(IP20 as
optional)
IP20
2
208
(8.19)
144
(5.67)
203
(7.99)
3.3
(7.3)
3
276
(10.87)
223
(8.78)
220
(8.66)
7.6
(16.8)
IP00
(IP20 as
optional)
A
mm
(In)
B
mm
(In)
C
mm
(In)
D
mm
(In)
Mounting
bolt
Weight
kg
(Ib)
Size
85
(3.35)
120
(4.72)
5
(0.20)
4
(0.16)
M4
1.3
(2.9)
1
132
(5.2)
148
(5.83)
6
(0.24)
3.4
(0.13)
M4
3.3
(7.28)
2
208
(8.19)
210
(8.27)
7.5
(0.3)
5
(0.2)
M5
7.6
16.8)
3
Mechanical Mounting
SSW-07 / ssw-08
Model
SSW070017
SSW070024
SSW070030
SSW070045
SSW070061
SSW070085
SSW070130
SSW070171
SSW070200
Table 3.1 Data for installation with dimensions in mm (in)
*Option for IP20 Kit
W
A
B
H
D
C
D
Soft-Starters
33
www.weg.net
SSW-07 and SSW-08 - Technical Data
Power Supply
Power
Control
Frequency
Degree of protection
Injected molded plastic case
Control
Starting Duty Cycle
Inputs
Outputs
Control Method
CPU
Types of Control
Frame Size 1
Frame Size 2 and 3
Digital
Relay
Protections (Standard)
Safety
Protections (with Accessory)
Functions / Resources
Standard
Command
Additional Functions / Resources
Programming Accessory
(HMI or Serial communication)
Supervision (Reading)
Accessories and Options
Options
Finishing
Color
Conformities / Standards
Safety
Low voltage
EMC
UL (USA) / cUL (Canada)
CE (Europe)
C-Tick (Australia)
(1) For the 45 to 200 A currents using the ventilation kit.
34
Soft-Starters
220 to 690 Vac
110 to 240 Vac (-15% to +10%), or 94 to 264 Vac
50 to 60 Hz (+/- 10%), or 45 to 66 Hz
IP20 in models from 17 to 85 A
IP00 in models from 130 to 200 A (IP20 an option)
Motor Voltage Variation
DSP type microprocessor (Digital Signal Processor)
Voltage ramp
Current limit
3 x In during 30s, 10 starts per hour
3 x In during 30s, 03 starts per hour ( availability of ventilation kit for applications
where 4 up to 10 starts per hour is demanded. )
3 isolated programmable inputs
02 relays with NO contacts, 240Vac, 1A, programmable functions
Overcurrent
Locked rotor
Overcurrent before By-pass
Excess starting time
Phase loss
Frequency outside tolerance
Inverted phase sequence
By-pass contact open
Overtemperature in power heatsink
Undervoltage in control supply
Motor Overload (class 5 to 30)
Undercurrent
Programming error
Current imbalance
Serial communication error
Under subcurrent before By-pass
HMI communication error
External fault
Overtemperature in motor PTC
Voltage ramp (Initial voltage: 30% to 90%)
Current limitation (150% to 450% of SSW-07 rated current)
Starting time (1 to 40s)
Kick Start (Off - 0.2 to 2s)
Deceleration ramp ( 0 to 40s)
Motor and SSW-07 current relation (50% to 100%)
Faults auto-reset
Thermal memory auto-reset
Factory standard reset
Soft-starter built-in By-pass
On, Off / Reset and Parameterization (function programming)
Starting time up to 999s
Deceleration time up to 999s
Program enabling password
Selection for Local / Remote operation
COPY function (SSW-07 >>> HMI and HMI >>> SSW-07)
Programmable rated voltage
Motor current (%Soft-Starter In)
Motor current (%motor In)
Motor current (A)
Current indication in each phase R-S-T
Supply network frequency
Apparent power supplied to load (kVA)
Soft-Starter status
Digital input and output status
Last 4 faults
Soft-Starter Software Version
Heatsink temperature
Motor thermal protection status
Plug-in type local HMI
HMI remote Kit
1,2,3,5,7.5 and 10m cable for remote HMI interconnection
RS-232 communication kit
SSW-07 interconnection cables>>> PC Serial (RS-232) 3 and 10m
RS-485 communication kit
Motor PTC kit
Ventilation kit for size 2 (45 to 85 A)
Ventilation kit for size 3 (130 to 200 A)
IP20 kit for size 3 (130 to 200 A)
Lid: Gray Ultra Mat
Cabinet: Blue Ultra Mat
UL 508 Standard- Industrial Control Equipment
EN60947-4-2;LVD 2006/95/EC Standard – Low voltage Directive
EMC 89/336/EEC Directive – Industrial Environment
Underwriters Laboratories Inc. – USA
Conformity test conducted by EPCOS
Australian Communication Authority
www.weg.net
SSW-07 and SSW-08 - Coding
EX SSW0X 0017 T
1
2
3
4
5
S
_ _
__
__
5
6
7
8
9
Z
10
1 - Market / Manual: EX= Export/English,
Spanish and Portuguese
2 - WEG SSW-07 and SSW-08 Series Soft-Starter
3 - Soft-Starter rated output current
4 - Soft-Starter input power supply:
T = Three-phase
5 – Power supply voltage:
5 = 220 to 575 V range
6 – Product version:
S = Standard
O = with Options
7 – Enclosure:
Blank = Standard
IP = IP20 for models from
130 A to 200 A
8 - Special Hardware:
Blank = Standard
9 - Special Software: Blank = Standard
10 - End of code:
Z = End of product code
indicator digit.
Soft-Starters
35
WEG Worldwide Operations
AUSTRALIA
WEG AUSTRALIA PTY. LTD.
3 Dalmore Drive
Carribean Park Industrial Estate
Scoresby VIC 3179 - Melbourne
Phone(s): 61 (3) 9765 4600
Fax: 61 (3) 9753 2088
info-au@weg.net
www.weg.net/au
BELGIUM
WEG BENELUX S.A.
Rue de l’Industrie 30 D,
1400 Nivelles
Phone(s): + 32 (67) 88-8420
Fax: + 32 (67) 84-1748
info-be@weg.net
www.weg.net/be
CHILE
WEG CHILE S.A.
Los Canteros 8600
La Reina - Santiago
Phone(s): (56-2) 784 8900
Fax: (56-2) 784 8950
info-cl@weg.net
www.weg.net/cl
CHINA
WEG (NANTONG) ELECTRIC
MOTOR MANUFACTURING CO.,
LTD.
No. 128# - Xinkai South Road,
Nantong Economic &
Technical Development Zone,
Nantong, Jiangsu Province.
Phone(s): (86) 0513-85989333
Fax: (86) 0513-85922161
info-cn@weg.net
www.weg.net/cn
COLOMBIA
WEG COLOMBIA LTDA
Calle 46A N82 - 54
Portería II - Bodega 7 - San
Cayetano II - Bogotá
Phone(s): (57 1) 416 0166
Fax: (57 1) 416 2077
info-co@weg.net
www.weg.net/co
FRANCE
WEG FRANCE SAS
ZI de Chenes – Le Loup
13 Rue du Morellon – BP 738
38297 Saint Quentin Fallavier
Phone(s): +33 (0) 4 74 99 11 35
Fax: +33 (0) 4 74 99 11 44
info-fr@weg.net
www.weg.net/fr
GERMANY
WEG GERMANY GmbH
Industriegebiet Turnich 3
Geigerstraße 7
50169 Kerpen-Turnich
Phone(s): +49 (0)2237/9291-0
Fax: +49 (0)2237/9292-200
info-de@weg.net
www.weg.net/de
INDIA
WEG Electric (India) Pvt. Ltd.
#38, Ground Floor, 1st Main
Road, Lower Palace Orchards,
Bangalore – 560 003
Phone(s): +91-80-4128 2007
+91-80-4128 2006
Fax: +91-80-2336 7624
info-in@weg.net
www.weg.net/in
ITALY
WEG ITALIA S.R.L.
V.le Brianza 20 - 20092 - Cinisello
Balsamo - Milano
Phone(s): (39) 02 6129-3535
Fax: (39) 02 6601-3738
info-it@weg.net
www.weg.net/it
JAPAN
WEG ELECTRIC MOTORS
JAPAN CO., LTD.
Matsumoto Bldg. 2F, 3-23-7
Kamata, Ohta-ku,
Tokyo, Japan 144-0052
Phone(s): (81) 3 3736-2998
Fax: (81) 3 3736-2995
info-jp@weg.net
www.weg.net/jp
MEXICO
WEG MEXICO, S.A. DE C.V.
Carretera Jorobas-Tula Km. 3.5,
Manzana 5, Lote 1
Fraccionamiento Parque
Industrial - Huehuetoca,
Estado de México - C.P. 54680
Phone(s): + 52 (55) 5321 4275
Fax: + 52 (55) 5321 4262
info-mx@weg.net
www.weg.net/mx
WEG Equipamentos Elétricos S.A.
International Division
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul - SC - Brazil
Phone:55 (47) 3276-4002
Fax: 55 (47) 3276-4060
www.weg.net
NETHERLANDS
WEG NETHERLANDS
Sales Office of
WEG Benelux S.A.
Hanzepoort 23C
7575 DB Oldenzaal
Phone(s): +31 (0) 541-571080
Fax: +31 (0) 541-571090
info-nl@weg.net
www.weg.net/nl
PORTUGAL
WEG EURO - INDÚSTRIA
ELÉCTRICA, S.A.
Rua Eng. Frederico Ulrich
Apartado 6074
4476-908 - Maia
Phone(s): +351 229 477 705
Fax: +351 229 477 792
info-pt@weg.net
www.weg.net/pt
RUSSIA
WEG RUSSIA
Pochainskaya Str. 17
Nizhny Novgorod
603001 - Russia
Phone(s): +7-831-2780425
Fax: +7-831-2780424
info-ru@weg.net
www.weg.net/ru
SPAIN
WEG IBERIA S.L.
Avenida de la Industria,25
28823 Coslada - Madrid
Phone(s) : (34) 916 553 008
Fax : (34) 916 553 058
info-es@weg.net
www.weg.net/es
SINGAPORE
WEG SINGAPORE PTE LTD
159, Kampong Ampat,
#06-02A KA PLACE.
Singapore 368328.
Phone(s): +65 6858 9081
Fax: +65 6858 1081
info-sg@weg.net
www.weg.net/sg
SWEDEN
WEG SCANDINAVIA AB
Box 10196
Verkstadgatan 9
434 22 Kungsbacka
Phone(s): (46) 300 73400
Fax: (46) 300 70264
info-se@weg.net
www.weg.net/se
UK
WEG ELECTRIC
MOTORS (U.K.) LTD.
28/29 Walkers Road
Manorside Industrial Estate
North Moons Moat - Redditch
Worcestershire B98 9HE
Phone(s): 44 (0)1527 596-748
Fax: 44 (0)1527 591-133
info-uk@weg.net
www.weg.net/uk
UNITED ARAB EMIRATES
WEG MIDDLE EAST FZE
JAFZA – JEBEL ALI FREE ZONE
Tower 18, 19th Floor,
Office LB181905
Dubai – United Arab Emirates
info-ae@weg.net
www.weg.net/ae
USA
WEG ELECTRIC CORP.
1327 Northbrook Parkway,
Suite 490
Suwanee 30024
Phone(s): 1-770-338-5656
Fax: 1-770-338-1632
info-us@weg.net
www.weg.net/us
VENEZUELA
WEG INDUSTRIAS VENEZUELA C.A.
Avenida 138-A
Edificio Torre Banco Occidental de
Descuento, Piso 6 Oficina 6-12
Urbanizacion San Jose de Tarbes
Zona Postal 2001
Valencia, Edo. Carabobo
Phone(s): (58) 241 8210582
(58) 241 8210799
(58) 241 8211457
Fax: (58) 241 8210966
info-ve@weg.net
www.weg.net/ve
782.06/122009 - The values shown are subject to change without prior notice.
ARGENTINA
WEG EQUIPAMIENTOS
ELECTRICOS S.A.
(Headquarters San
Francisco-Cordoba)
Sgo. Pampiglione 4849
Parque Industrial San Francisco
2400 - San Francisco
Phone(s): +54 (3564) 421484
Fax: +54 (3564) 421459
info-ar@weg.net
www.weg.net/ar
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising