RC-22 RC-60 RC-42, RC-44 Remote Control

RC-22 RC-60 RC-42, RC-44 Remote Control
T1358 - Jablotron -JA-60 - AN
27.12.2005
9:27
Stránka 4
RC-22
RC-42, RC-44
Remote Control
RC-42
The RC-22 is a large-size wireless remote controller used in JA-6x systems. It can especially be used
as a panic or emergency button. It is designed for walls
or under-desk mounting. It can also be used as a wireless switch with UC-2xx receivers. An LED indicator
confirms button pressing.
Power
Battery life time
Working range
Dimensions
6 V battery (L1016)
typical 1 year
max. 100 m (open area)
80 x 80 x 15 mm
RC-28
Wireless Door Bell Button
RC-60
Remote Control
Remote Control
RC-44
The RC-44 remote control combines two pairs of
buttons. It can be used to operate multiple wireless
Jablotron devices. For example one RC-44 can control
a house alarm, gate and garage door or two independent partitions in the house alarm or up to 6 different
devices when used with Jablotron UC receivers.
For easy operation the RC-44 has its buttons marked by symbols of the lock ( , ) and by open – close
“semaphore” ( , ).The RC-42 is the same remote control as the RC-44 except that it is built into the housing
with only two buttons ( , ), which have identical functions to the left pair of RC-44 buttons.
The RC-44 has a unique optional “keypad locking”
feature to prevent accidental activation or its unauthorized use.
By simultaneous pressing of both buttons in the
pair the panic signal will be sent to the control unit.
The RC-28 remote control is a single channel
transmitter that is used especially with the UC-260
acoustic indicator as a wireless doorbell button. It can
also be used with other UC-2xx receivers.
Power
Battery life time
Operating frequency
Working range
Dimensions
6 V battery (L1016)
typical 1 year
433 MHz
max. 50 m (open area)
80 x 28 x 15 mm
SP-01
Loud Intercom
Power
alkaline battery L1016 6V
Battery life time
typical 1 year
Working range with JA-6x
30 m (open area)
Dimensions
52 x 18 x 12 mm
PC-60B
The RC-60 is used to arm and disarm JA-6x wireless control panels. It can be connected to an external
controller, such as an access system, card or chip reader, electrical lock etc. It provides tamper protection for
the external device. Two inputs can be used in different
modes.
In the first mode one input is used for arming and
the other one for disarming.
In the second mode connecting the A input to the
GND triggers the ARM signal and disconnecting it from
the GND triggers the DISARM signal. Temporary or
permanent connection of the B input to GND causes
PANIC signal transmission.
THE JA-60 WIRELESS SYSTEM
BRIEF PRODUCT CATALOGUE
GSM Building Alarm JA-63KRG PROFI
Power
2x 1.5 V AAA batteries
Battery life time
typical 1 year
External inputs
2 (EOL or NC contacts)
Indication LED
testing & low battery
Operating frequency
433 MHz
Working range
max. 100 m (open range)
Complies with
EN 50131-1 grade 2
Dimensions
110 x 30 x 27 mm + antenna 40 mm
32 wireless detectors
AN-01A
Computer Interface
Wire Antenna
8 wireless remote
controls or keypads
Wireless sirens
and indicators
SP-01 is designed to be connected to the simulated telephone line connector on the JA-60GSM communicator. Loud Intercom allows to talk and to listen to
the monitored premises in the case of alarm or other
event (fire, panic and others).
The PC-60B allows a computer to be connected
to JA-63Kxx PROFI and JA-65Kxx MAESTRO control
panel. Using the ComLink software, you can supervise
the system, download the event’s log, setup the system,
view RF signal etc.
PC connection
Operating system
Cable length
GSM Link
A web page for remote access to the JA-60GSM
USB port
MS Windows
2.0 m
JA-60U
Remote Access Modem
The AN-01 wire antenna is designed to be used
with Jablotron radio products with operating frequency
of 430 - 450 MHz.
System Bus Keypad
Frequency
Installation
Cable length
Operating temperature
430 - 450 MHz
vertical
1.6 m
10 °C to 40 °C
AN-03
Outdoor Antenna
Internet access
www.GSMlink.cz is an internet web page for
remote access to the JA-60GSM communicator or
other Jablotron GSM products. Access to GSM link is
protected by a password and by a unique registration
code for the device.
GSM link provides the installer with a comfortable tool to monitor and setup the system in a graphical,
user-friendly environment. A user can control, check
the status of the system and set parameters that can
be changed in user mode.
Data between GSM link and the device is transferred
via SMS messages or better still, if it is supported by the
SIM card in the device, via GSM/GPRS.
4 hardwired zones
The JA-60U modem connects a personal computer remotely to the system via a telephone line.
The provided ComLink software allows you to supervise the system, to read data from the control panel’s
memory, to setup the system etc.
Power
230 V AC – 12 V DC adapter (max. 1.5 W)
Communication protocol
Jablotron’s encrypted
Operating system
MS Windows
PC connection
COM serial port
Dimensions
130 x 95 x 26 mm
The AN-03 antenna is designed to be used with
Jablotron radio products with operating frequency
of 430 - 450 MHz. It is suitable for outdoor use.
Frequency
Installation
Cable length
Operating temperature
430 - 450 MHz
vertical
3m
40 °C to 70 °C
JA60-012006-EN
Phone calls and SMS
Home appliances
remote control
Internet connection
www.jablotron.com
T1358 - Jablotron -JA-60 - AN
27.12.2005
9:27
JA-60E
Stránka 2
UC-222
JA-60F
JA-60P
JA-60N
JA-60B
System Bus Keypad
Wireless Keypad
Universal Receiver
Wireless P.I.R. Detector
Wireless Magnetic Door Contact
Wireless Glass Break Detector
The JA-60E is a bus system keypad for Jablotron
JA-6x control panels. It is connected to the control
panel by a 4-wire cable. Multiple keypads can be connected to a single control panel. The keypad has a built
in tamper sensor and it also checks the number
of attempts to enter an access code. The alarm system's status is indicated by the LED indicators, the built
in display and built in buzzer. The backlit keypad can be
used to operate and to program the system. The
JA-60E can be used together with the JA-60U modem
to remotely operate the control panel.
The JA-60F is an optional wireless keypad for
JA-6x wireless control panels. It can operate the system in exactly the same way as the built-in keypad on
the control panel or the JA-60E hardwired bus system
keypad. The LED indicators, display and built-in buzzer
indicate the alarm system's status. Multiple keypads
can be used with a control panel. The keypad has
a built in tamper sensor and it also checks the number
of attempts to enter an access code. The keypad performs regular auto testing and reports its conditions
regularly to the system for full supervision. Being wireless, it can help an installer to monitor the system functions when performing a “walk” test. For longer working
range an optional external antenna, AN-01, can be
used.
The UC-222 wireless controller is powered by
230 V AC. Its output relay contact operates at 230 V
AC, as well. Up to 30 remote controls, wireless detectors or keypads can be enrolled to the unit. There are
four different operating modes available for each remote control. The controller can be used for automatic
lighting control, remote operating of electric appliances, access control etc.
When used in conjunction with a JA-6x wireless
control panel, the output relays of the UC-222 unit can
copy signals from the control panel‘s outputs. The
UC-222 can also receive signals directly from RC-xx
controllers and JA-60 detectors for various applications.
The JA-60P is an intruder detector designed to
detect human body movement in a protected area.
Digital processing insures a high immunity to false
alarms and outstanding stability. The JA-60P uses
a sophisticated radio communication protocol with
a high level of data safety. The detector performs regular auto testing and reports its condition regularly to the
system for full supervision. Built in tamper sensors protect against opening or removal from its location.
The JA-60N magnetic door detector is equipped
with a magnet. Movement of the magnet triggers the
internal sensor in the detector. It can trigger an instant
or delayed intruder alarm and it also has built in tamper sensors. Special inputs for external sensors are
available. The JA-60N uses a sophisticated radio communication protocol with a high level of data safety. The
detector makes regular auto testing and reports its
condition regularly to the system for full supervision.
The JA-60B is an acoustic glass break detector
that provides easy and reliable protection against robbery. It ensures extremely high reliability and false
alarm immunity. One sensor covers an entire room,
regardless of the number of windows. A dual technology detection method (air pressure and sound analysis)
is combined with digital processing to guarantee high
sensitivity to the breaking of glass. The detector is also
protected against tampering. The detector is regularly
supervised. The JA-60B can be tested with GBT-212
simulator.
Power
Power
Power consumption
Operating frequency
Operating range
Peripheries
Power
2x 1.5 V AAA batteries
Battery life time
typical 1 year
Detection method
magnetic reed sensor
External sensor inputs
input & tamper (EOL)
LED indication
testing & low battery
Operating frequency
433 MHz
Working range
max. 100 m (open area)
Complies with
EN 50131-1 grade 2
Dimensions
110 x 30 x 27 mm + antenna 40 mm
Power
2x 1.5 V AAA batteries
Battery life time
typical 1 year
Built in sensor
dual technology acoustic sensor
LED indication
testing & low battery
Working distance
max. 9 m
Operating frequency
433 MHz
Working range
max. 100 m (open area)
Complies with
EN 50131-1 grade 2
Dimensions
55 x 75 x 22 mm + antenna 40 mm
Power supply
12 V DC (from the bus line)
Power consumption
typ. 40 mA
Codes
master & 14 user codes, service code
Connecting cable
4-core cable, max. 100 m
Complies with
EN 50131-1 grade 2
Dimensions
140 x 80 x 26 mm
4x 1.5 V AAA batteries
or 12 V DC power adaptor (optional)
Battery life time
typical 1 year
Codes
master & 14 user codes, service code
Radio communication
bidirectional,
digital hopping code
Operating frequency
433 MHz
Working range
max. 50 m (open area)
Complies with
EN 50131-1 grade 2
Dimensions
140 x 80 x 26 mm + antenna 80 mm
JA-60A
UC-260 / UC-261
Wireless Outdoor Siren
The JA-60A siren is designed for outdoor use. It is
powered from its own AC adapter and has a built in
back up battery. The siren communicates wirelessly
with the JA-6x wireless control panel with two-way
communication. It contains a high-powered siren and a
strobe light. In addition to signaling alarms, it can also
provide arming and disarming chirps. The siren performs regular self-testing and reports its condition
regularly to the system for full supervision. Built in
tamper sensors trigger an alarm if there is any attempt
to tamper with the siren. For longer range, an optional
external antenna, AN-01A, can be used.
230 V AC
(110 V AC optional) – adapter included
Back up battery
6 V, 1.3 Ah (included)
Battery life time
up to 5 years
Siren
piezoelectric, 118 dB
Siren timer
set by the control panel
Strobe light timer
60 minutes
Operating frequency
433 MHz
Working range
max. 100 m (open area)
Complies with
EN 50131-1 grade 2
Dimensions
230 x 158 x 75 mm
Output relay
Modes
Dimensions
230 V AC (110 V AC optional)
max. 1.5 W
433 MHz
100 m (30 m for RC-11)
30 remote controls
or wireless detectors
max. 6.3 A/250 V
short pulse (3 sec), long pulse (2 min),
latch, ON/OFF
100 x 73 x 25 mm + antenna 86 mm
UC-216
Power
Battery life time
Detection method
Coverage
Optional lenses
2x 1.5 V AAA batteries
typical 1 year
dual PIR with digital processing
12 m, 120°
corridor, horizontal
and vertical curtain
LED indication
testing & low battery
Operating frequency
433 MHz
Working range
max. 100 m (open area)
Complies with
EN 50131-1 grade 2
Dimensions
70 x 90 x 65 mm
JA-60V
JA-60SR / JA-60SP
JA-60G
Acoustic Indicator
Universal Receiver
Wireless Outdoor PIR Motion Detector
Wireless Smoke Detector
Wireless Gas Leak Detector
The UC-260 “plug-in” wireless acoustic indicator
can be used as a high-power indoor alarm siren for the
JA-6x system. It can also indicate entrance/exit delays.
With the RC-28 or RC-22 buttons the indicator can also
be used as a doorbell. Selectable “melody ” sounds can
be indicated, as well, when desired detectors of the
alarm system are triggered. Up to 8 RC-xx remote controls or JA-60 detectors can be enrolled directly to the
UC-260.
Jablotron offers also UC-261 wireless acoustic
indicator (two way communication), which send an
error report to the control panel in the case of disconnection from the power.
The UC-216 is a three-channel receiver of coded
signals. The status of the outputs is indicated on the
front panel. The UC-216 can be used to control alarm
and access systems, to trigger a panic alarm, etc.
There are 4 different operating modes available for
each remote control. A digital hopping code ensures
high security. When used in conjunction with a JA-6x
wireless control panel, the output relays of the UC-216
unit can copy signals from the control panel‘s outputs.
The UC-216 can also receive signals directly from
RC-xx controllers and JA-60 detectors for various
applications.
The JA-60V is an outdoor intruder detector designed to detect human body movement in an open area.
Used PIR detector produced by Optex (Optex VX
402R) has two double-layered detection patterns
(upper and lower) both have to be activated to trigger
the alarm. This reduces false alarms, particularly those
caused by temperature changes, light reflection or
small animals. A tamper triggers an alarm if there is
any attempt to open the detector. The built-in transmitter is compatible with all JA-6X control panels.
A smoke detector recognizes smoke and wirelessly transmits this information to a control panel.
It also has a built in siren to warn people in the immediate vicinity. Functioning of the detector can be checked anytime by pressing the test button. Testing can
also be easily activated using a standard audio/video
infrared remote control. The detector is monitored
regularly.
Ionic detectors are not suitable for places with
a high concentration of a steam. Optical detectors on
the other hand should not be used in a dusty environment.
The JA-60G reacts to combustible gases (natural
gas, city gas, propane, butane, methane, hydrogen
etc.) by signaling a fire alarm. It also has a built in buzzer to warn people in the immediate vicinity and an output relay to control an electrical valve if installed in
a gas supply inlet.
The detector is regularly supervised.
Power
Power consumption
Siren mode
Doorbell & Chime
Compatible with
Operating voltage
12 - 24 V DC or 15 V AC
Power consumption
stand-by 10 mA
Operating frequency
433 MHz
Operating range
100 m (30 m for RC-11)
Output relays
max. 120 V/1 A
Output transistor
max. 40 V/0.2 A
Modes
short pulse (3 sec), latch, ON/OFF,
garage door mode
Complies with
EN 50131-1 grade 2
Dimensions
100 x 73 x 25 mm + antenna 86 mm
Power
230 V AC (110 V AC optional)
1.5 W
115 dB
8 melodies available
JA-6x control panels;
RC-xx remote controls;
JA-60 detectors
Operating frequency
433 MHz
Working range
max. 100 m (open area)
Dimensions
90 x 65 x 45 mm + antenna 40 mm
Power
Battery life time
Working frequency
Coverage
Working range
Complies with
Waterproof
Humidity
Dimensions
3 V – 2x 1.5 V AAA batteries
about 1 year
433.92 MHz
max. 12 m/90°
max. 100 m (open area)
EN 50131-1, class II
IP 54
95 %
198 x 80 x 108 mm
Power
Battery lifetime
Detection method
Covered space
Built in siren loudness
LED indication
Operating frequency
Working range
Dimensions
2x 1.5 V AA batteries
typical 1 year
ionic (max. 4 kBq.)/optical
chamber
50 m3
94 dB/m
self-testing every 60 sec
433 MHz
max. 100 m (open area)
∅ 120 x 40 mm
Power
230 V AC (optional 110 V AC)
Detection method
hot fiber sensor
Relay output over switching contact max. 230 V/5 A
Sensitivity
two levels (10 and 20% of LEL)
Built in buzzer
94 dB/0.3 m
Area covered
50 m2
Operating frequency
433 MHz
Working range
max. 40 m (open area)
Dimensions
100 x 73 x 39 mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising