INSTALLATION MANUAL
INSTALLATION MANUAL
SEE-THRU DIRECT VENT FIREPLACE
English and French Installation Manuals Available Through Your Local Dealer or Visit Our Website at www.kozyheat.com
Les manuels d’installation en anglais et en français sont disponibles chez votre détaillant local ou en visitant notre site Web : www.kozyheat.com
IMPORTANT:
This installation manual is to be used in conjunction with SUPPLEMENTAL
INSTALLATION AND HOMEOWNER INFORMATION MANUAL. Read both manuals before installing
and operating appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This appliance may be installed in an aftermarket permanently located,
manufactured home (USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.
—Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
◙ Do not try to light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
◙ If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
www.kozyheat.com
Report No. 216-F-13b-6.5
TMT-APRIL 2013-REV-11-SEPARATE
INTRODUCTION
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
CONGRATULATIONS!
We welcome you as a new owner of a Kozy Heat gas fireplace. Kozy Heat products are
designed with superior components and materials and assembled by trained craftsmen who
take pride in their work. The burner and valve assembly are 100% test-fired and the complete
fireplace is thoroughly inspected before packaging to ensure that you receive a quality product.
Our commitment to quality and customer satisfaction have remained the same for over 30
years. We offer a complete line of gas and wood fireplaces, unique cabinets and stylish
accessories to compliment any décor. Adding a fireplace is one of the best ways to increase the
value of your home and we are proud to offer a network of dealers throughout the country to
help make your experience everything you imagine. We pride ourselves in being dedicated to
not only function and reliability, but customer safety as well. We offer our continual support
and guidance to help you achieve the maximum benefit and enjoyment from your Kozy Heat
gas fireplace.
Jim Hussong
President
Dudley Hussong
Board Chairman
Homeowner Reference Information
We recommend that you record the following information about your fireplace.
Model Name:______________________________ Date purchased/installed:_____________________________________
Serial Number:____________________________
Location on fireplace:________________________________________
Dealership purchased from:__________________
Dealer Phone:______________________________________________
Notes:_______________________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
1
TABLE OF CONTENTS
INTRODUCTION
Introduction and Homeowner Reference Information
VENTING (cont.)
1
TABLE OF CONTENTS
Table of Contents
2
20
Pier Conversion Installation
3
Log Set Installation
4
Control Board Removal
24
24
Fireplace Dimensions
5
Control Board Installation
Clearances
6
GRILL SET
Installation Overview
7
Grill Set Installation / Removal
Placement Clearance Requirements
7
FINALIZING THE INSTALLATION
PREPARE THE FIREPLACE
26
27
8
Burner Tube Adjustment / Troubleshooting
Top Stand-Off Assembly & Installation
8
MAINTENANCE
FRAMING
Maintenance
Vertical Terminations
9
WARRANTY
Horizontal Terminations
9
Warranty
Minimum Finished Opening Dimensions
10
WALL PASS-THRU INSTALLATION
Wall Pass-Thru Installation
11
HORIZONTAL HEAT SHIELD INSTALLATION
Horizontal Heat Shield Installation
11
MANTEL REQUIREMENTS
Mantel Requirements
12
GLASS FRAME ASSEMBLY
Glass Frame Assembly Removal / Removal
12
GAS LINE CONNECTION
Gas Line Connection
13
VENTING
Approved Venting
14
Restrictor
14
Elbows
14
Horizontal Vent System Clearances
15
Min. / Max. Horizontal Vent System Information
15
Vertical Vent System Clearances
15
Min. / Max. Vertical Vent System Information
15
Horizontal / Vertical Combination Venting
16
Kozy Heat #800-1 Series Flex Vent Installation Instructions
17-18
2
25
Restrictor Troubleshooting / Installation after Termination Completion
Nailing Flange Assembly & Installation
10
22-23
CONTROL BOARD
SPECIFICATIONS
Wall Enclosure Rough Opening
21
LOG SET INSTALLATION
COMMONWEALTH OF MASSACHUSETTS INFORMATION
Commonwealth of Massachusetts Information
19
Vertical Cap Requirements
PIER CONVERSION INSTALLATION
SAFETY INFORMATION
Safety Information
Termination Cap Location
28
29-30
SAFETY INFORMATION
This fireplace has been tested by OMNI-Test Laboratories, Portland, Oregon and complies with:
ANSI Z21.88-2009/CSA 2.33-2009, “Standard for Vented Gas Fireplace Heaters.”
CAN/CGA 2.17-M91 (R2009), “Gas-Fired for Use at High Altitudes.”
CAN/CSA P.4.1-09, “Testing Method for Measuring Annual Efficiency”.
This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation Code, CSA B149.1
Installation and repair should be done only by a qualified service person. The appliance should be inspected by a
qualified service person before use. Annual inspection by a qualified service person is required to maintain warranty.
More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulation air passageways of the appliance be kept clean.
If this appliance is installed directly on carpeting, tile or other combustible material other than wood flooring, the
appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at
risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other flammable material should not be placed on or near the appliance.
Adequate accessibility clearances for servicing and proper operation must be maintained.
This appliance must not share or be connected to a chimney flue serving any other appliance.
Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor and liquids.
The flow of combustion and ventilation air must not be obstructed.
Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.
The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance.
Work should be done by a qualified service technician.
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH THE GLASS/FRAME ASSEMBLY REMOVED, CRACKED
OR BROKEN. REPLACEMENT OF THE GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR
QUALIFIED SERVICE PERSON .
The glass assembly, Part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass assembly.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance.
Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this appliance.
Keep burner and control compartment clean.
Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect this
appliance and to replace any part of the control system and any gas control which has been under water.
3
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
NOTE
The following requirements reference various Massachusetts and national codes not contained in this manual.
For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than (7) feet above finished grade in the
area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
INSTALLATION OF CARBON MONOXIDE DETECTORS
At time of installation of side wall horizontally vented gas fueled equipment, the installing plumber or gas-fitter shall observe that a hard wired carbon
monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing
plumber or gas-fitter shall observe that a battery operated or hard wired carbon monoxide detector is installed on each additional level of the dwelling,
building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an
alarm shall be installed.
APPROVED CARBON MONOXIDE DETECTORS
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS
certified.
SIGNAGE
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum of eight (8) feet above grade directly in line
with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print no less the one-half inch
(1/2) in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
INSPECTION
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the
inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08 (2) (a) 1 through 4.
EXEMPTIONS
The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through 4:The equipment listed in Chapter 10 entitled “Equipment Not Required To Be
Vented” in the most current edition of NFPA 54 as adopted by the Board; and Product Approved side wall horizontally vented gas fueled equipment installed
in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components
with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
Detailed instructions for the installation of the venting system design or the venting system components; and
A complete parts list for the venting system design or venting system.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED
When the manufacturer of Product Approved side wall horizontally vented gas equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements shall be satisfied by the manufacturer:
The referenced “special venting systems” instructions shall be included with the appliance or equipment installation instructions and;
The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed
installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
4
SPECIFICATIONS
FIREPLACE DIMENSIONS
FIREPLACE
DIMENSIONS
WARNING
LETTER KEY
A
B
C
D
E
F
G
H
I
DESCRIPTION
Height
Width
Depth
Glass Frame
Height
Stand-off
Height
Vent end to
Vent Center
See-Thru sides
to Vent Center
Front to Gas
Line Hole Center
Floor to Gas Line
Hole Center
INCHES
34-1/2
38-3/4
24
26
11-1/2
7-7/8
12
8-1/4
2-1/2
MILLIMETERS
876
984
610
660
292
200
305
210
64
All stand-off brackets must be attached to fireplace. Do not remove. Top stand-off brackets are not load bearing.
Non-combustible zone: Top stand-offs provide 11-1/2” (292mm) minimum clearance to header. Use only non-combustible
material in this area for entire width of fireplace. Do not use wood, sheetrock etc. in this zone. Other clearances apply.
All clearances must be maintained.
E
11-1/2”
(292mm)
A
34-1/2”
(876mm)
D
26”
(660mm)
Front View
I
2-1/2”
(64mm)
H
8-1/4”
(210mm)
B
38-3/4”
(984mm)
Top View
C
24”
(610mm)
F
7-7/8”
(200mm)
G
12”
(305mm)
Figure 5a
5
SPECIFICATIONS
WARNING
All stand-off brackets must be attached to fireplace. Do not remove. Top stand-off brackets are not load bearing.
Non-combustible zone: Top stand-offs provide 11-1/2” (292mm) minimum clearance to header. Use only non-combustible
material in this area for entire width of fireplace. Do not use wood, sheetrock etc. in this zone. Other clearances apply.
All clearances must be maintained.
SEE-THRU
PIER
68”
(1727mm)
33-1/2”
(851mm)
42-1/4”
(1073mm)
24”
(610mm)
46”
(1168mm)
46”
(1168mm)
24”
(610mm)
1-3/4”
(44mm)
IMPORTANT
1-3/4”
(44mm)
Overall finished depth: 24” (610mm). This measurement includes facing material. Material used will determine rough opening depth.
This depth must not be less than 19” (482mm) to maintain non-combustible zone requirements.
Figure 6a
CLEARANCES
Top of unit face to header
11-1/2” (292mm)
From unit vented/non-vented ends
1-3/4” (44mm)
From optional decorative full door faces
1/4” (6mm)
To flooring
0” (0mm)
See-thru applications: Unit top to ceiling
33-1/2” (851mm)
Pier applications: Unit top to ceiling
24” (610mm)
Unit side to adjacent sidewall
1-3/4” (44mm)
Unit front to combustibles
36” (914mm)
Top of unit to 3/4” (19mm) trim
11-3/4” (298mm)
Mantel 12” (305mm) deep from top of fireplace
12” (305mm)
6
SPECIFICATIONS
INSTALLATION OVERVIEW
NOTE
The qualified installer should follow the procedure best suited for the installation.
1.
Frame an opening for the fireplace, allowing for vent installation (top or rear) and type of installation (corner or flat wall application).
2.
If masonry (optional) is used, prepare foundation for the masonry load. A lintel is required to support the added weight above fireplace.
3.
Attach nailing flanges to fireplace.
4.
Insert fireplace into framing.
5.
Install hearth (if applicable).
6.
Complete gas line installation.
7.
Complete electrical hook-up. Install any standard or optional electrical components at this time.
8.
Complete venting installation.
9.
Secure fireplace to flooring through holes in outer box bottom and to framing with nailing flanges. Verify all clearances at this point.
10. Install facing material, mantel or cabinetry, allowing room for optional full face doors, if applicable.
11. Install logs.
12. Install grills and optional decorative doors / faces.
13. Verify proper operation of fireplace and all components.
PLACEMENT CLEARANCE REQUIREMENTS
This fireplace must be installed on a level surface capable of supporting the fireplace and venting.
Fireplace must be placed directly on wood or non-combustible surface (not linoleum or carpet) extending entire depth and width of
fireplace.
Due to high surface temperatures, fireplace should be located out of traffic and away from furniture and draperies.
This fireplace may be installed in a bedroom.
Please be aware of the large amount of heat this fireplace will produce when determining a location.
7
PREPARE THE FIREPLACE
NAILING FLANGE ASSEMBLY & INSTALLATION
IMPORTANT
Mobile home installations: Fireplace must be secured to floor.
When installed, nailing flanges provide the minimum 1-3/4” (44mm) clearance from fireplace sides. Depending on facing material, nailing flanges
can be adjusted forward or back up to 1/2” (13mm).
1.
Remove nailing flanges from fireplace sides.
SEE-THRU INSTALLATIONS:
All (8) stud tabs will be used to secure fireplace to framing studs.
REMOVE SCREWS
PIER INSTALLATIONS:
Only vented end stud tabs (4) are used to secure fireplace to framing studs.
2.
Bend nailing flange as shown in illustration below.
3.
Secure to fireplace and framing studs as shown.
4.
Use appropriate screws or fasteners to secure fireplace to flooring through
holes located in fireplace bottom.
BEND AT
PERFORATION
FRAMING STUD
NAILING FLANGE
INSTALLED
Figure 8a
STAND-OFF ASSEMBLY & INSTALLATION
IMPORTANT
Top stand-off brackets must be formed and attached prior to positioning fireplace into framed opening.
Stand-off brackets are not load bearing.
Never permanently remove these assemblies from fireplace – they must be installed regardless of finish material used.
Stand-off brackets are attached to fireplace top in a flat state for shipping.
1. Remove and save stand-off brackets and screws.
2. Remove screws located under stand-off brackets.
3. Form each stand-off bracket as shown.
BEND AT PERFORATIONS
4. Re-attach to fireplace using screws previously removed.
Figure 8b
8
FORMED STAND-OFF
FRAMING
Determine exact position of your fireplace, including hearth height, width, and depth, (if applicable). If possible, place fireplace in such a
manner that vent termination will be placed between two studs, eliminating the need for additional framing.
If masonry is to be used (optional), prepare the necessary foundation for the masonry load. When masonry construction is being used, a
lintel must be used over the top of fireplace to support the added weight. See-Thru applications: #617 Lintel Iron
Pier applications:
#788-T Lintel Iron
Build hearth to desired size and height. If a hearth extension is desired, combustible material may be used.
NOTE
WARNING
Consider height of hearth finish material (stone, brick, etc.) when building fireplace platform. The bottom of fireplace must be
level with finished hearth to allow for lower grill operation and proper fit of optional decorative full door faces.
Install fireplace on hard metal or wood surface extending the full width and depth of fireplace.
Minimum platform size: 38-3/4” (984mm) wide x 24” (610mm) deep.
FIRE HAZARD: Do NOT install directly on carpeting, vinyl, or any combustible material other than wood.
IMPORTANT
Vent cap location must be in compliance with guidelines on page 19 of this manual.
VERTICAL TERMINATIONS
Follow vent pipe manufacturer’s installation instructions for vertical terminations. A minimum 1” (25mm) clearance on all sid es of
vertical vent pipe must be maintained.
IMPORTANT
Restrictor (included) required for all vertical terminations. See page 14 for installation instructions.
HORIZONTAL TERMINATIONS
Horizontal Vent Heat Shield must be installed when using a 90˚ elbow to horizontally position the vent system or when using
#800-1 Series Kozy Heat flexible vent system for horizontal terminations. See page 11 for installation instructions.
IMPORTANT
Kozy Heat wall thimble pass-thru (#800-WPT or #800-WPT2) must be used on all horizontal vent runs.
Follow instructions on page 11.
Follow vent pipe manufacturer’s installation instructions for horizontal terminations. Include
required 3” (76mm) top clearance and 1” (25mm) sides and bottom clearances for approved
rigid vent systems and the Kozy Heat #800-1 series flexible vent system.
10-7/8”
(276mm)
Frame a 12-1/2” (318mm) high (H) x 10-7/8” (276mm) wide (W) opening on exterior wall
for chimney termination. This opening size includes required 3” (76mm) at top and
1” (25mm) at sides and bottom for rigid vent systems and Kozy Heat #800-1 series flex vent
systems.
MINIMUM HORIZONTAL FRAMING DIMENSIONS
VENT PIPE TOP (A)
12-1/2”
(318mm)
NAT. GAS
LP GAS
RIGID PIPE
48-1/8” (1222mm)
52-3/4” (1340mm)
KOZY HEAT #800-1 SERIES FLEX PIPE
54-1/2” (1384mm)
54-1/2” (1384mm)
Figure 9a
9
FRAMING
WALL ENCLOSURE ROUGH OPENING
Framing dimensions should allow for wall covering thickness and fireplace facing materials. If using a hearth, adjust rough
opening size as necessary to maintain at least the minimum clearance requirements.
IMPORTANT
Overall finished depth is 24” (610mm). This measurement includes facing material. Material used will determine framing depth.
This depth must not be less that 19” (482mm) to maintain non-combustible zone requirements.
Header must be installed in the upright position to maintain non-combustible zone requirements.
Non-combustible facing material may be applied over (but not directly to) fireplace. This will prevent facing material from
falling off due to heat expansion. Do not obstruct the flow of ventilation air.
MINIMUM FINISHED OPENING DIMENSIONS: SEE-THRU INSTALLATIONS
(APPLIES TO BOTH HORIZONTAL AND VERTICAL VENTING TERMINATIONS)
46” (1168mm) High x 42-1/4” (1073mm) Wide x 24” (610mm) Deep.
MINIMUM FINISHED OPENING DIMENSIONS: PIER INSTALLATIONS
(APPLIES TO BOTH HORIZONTAL AND VERTICAL VENTING TERMINATIONS)
46” (1168mm) High x 40-1/2” (1029mm) Wide x 24” (610mm) Deep.
NOTE
Provide adequate clearance in front of fireplace to operate lower grill, open and close optional decorative doors / full door faces,
access components, installation of gas line, fan, etc.
WARNING
DO NOT OBSTRUCT UPPER AND LOWER GRILL OPENINGS. ROOM AIR ENTERS THROUGH LOWER PASSAGE, IS HEATED AND
EXITS THROUGH THE UPPER PASSAGE. BLOCKING THESE PASSAGES MAY RESULT IN OVERHEATING, CREATING A
POTENTIALLY HAZARDOUS SITUATION.
NOTE
Measurements are FINISHED dimensions (wall covering / facing material included).
24”
(610mm)
40-1/2”
(1029mm)
42-1/4”
(1073mm)
24”
(610mm)
46”
(1168mm)
46”
(1168mm)
Pier application with minimum venting for
horizontal application shown.
See-Thru application shown for
vertical application.
Figure 9a
10
WALL PASS-THRU INSTALLATION
IMPORTANT
#800-WPT or #800-WPT2 Wall Pass-Thru must be used on all horizontal vent terminations.
This includes both interior and exterior walls. Follow instructions below.
FRAMING DIMENSIONS FOR #800-WPT KOZY HEAT WALL PASS-THRU
12-1/2” (318mm) HIGH x 10-7/8” (276mm) WIDE
WARNING
IMPORTANT
MAINTAIN ALL CLEARANCES AS STATED IN THIS INSTALLATION MANUAL.
If using Kozy Heat series flexible vent system, remove inner ring on each wall pass-thru section with a tin snips.
This will provide adequate room for the flexible vent system.
A.
Measure wall thickness; cut insulation panel (included) this length.
B.
Install wall pass-thru section marked #1 (3/8” (10mm) flange) into framed opening. Secure to interior wall with screws (not provided).
C.
From the exterior, place insulation between flange and top of framed opening in wall pass-thru section #1.
D.
Install section marked #2 of wall pass-thru into framed opening, overlapping metal sections as necessary to accommodate wall thickness.
Secure to exterior wall with screws (not provided).
HEAT SHIELD MUST BE FLUSH
WITH WALL PASS -THRU.
3/8” (10mm) FLANGE MUST
BE ON INSIDE WALL.
INSULATION
CUT RING OUT OF BOTH SECTIONS IF INSTALLING
#800-1 SERIES FLEX VENTING.
Figure 11a
HORIZONTAL HEAT SHIELD INSTALLATION
WARNING
The horizontal heat shield (included) must be installed if a 90˚
elbow is installed directly off top of fireplace, or if using Kozy Heat
#800-1 series flexible vent system in a horizontal venting
configuration.
1.
Remove center insulation section from top of fireplace.
2.
Install 90˚ degree elbow onto fireplace following vent pipe manufacturer’s
instructions.
3.
Install remaining venting.
4.
Bend sides and end of horizontal vent heat shield at 90˚ angles.
5.
Align holes in horizontal heat shield to holes in fireplace top, secure with (8)
screws provided in fireplace components packet.
Remove center
insulation section
Horizontal Vent
Heat Shield
installed
11
Figure 11b
MANTEL REQUIREMENTS
20 in.
(508mm)
12 in.
(305mm)
20 in.
(508mm)
3/4 in.
(20mm)
12 in.
(305mm)
11-3/4 in.
(298mm)
Figure 12a
GLASS FRAME ASSEMBLY
CAUTION
TO PREVENT GLASS FRAME ASSEMBLY FROM FALLING FROM FIREPLACE AND BECOMING DAMAGED, FOLLOW THESE
INSTRUCTIONS EXACTLY WHEN REMOVING AND INSTALLING GLASS FRAME ASSEMBLY.
REMOVE GLASS FRAME ASSEMBLY
1.
Locate spring-loaded handles securing glass frame assembly at top &
bottom of firebox.
2.
Pull bottom handles out and down to release glass frame assembly bottom.
3.
Pull top handles out and up to release glass frame assembly top.
4.
Remove glass frame assembly from fireplace.
Pull latches out and up to release glass frame
assembly top.
Pull latches out and down to attach glass frame
assembly top.
INSTALL GLASS FRAME ASSEMBLY
1.
Place glass frame assembly onto fireplace front.
2.
Pull top handles out and down to secure glass frame assembly top.
3.
Pull bottom handles out and up to secure glass frame assembly bottom.
Pull latches out and down to release glass frame
assembly bottom.
Figure 12b
12
Pull latches out and up to attach glass frame
assembly bottom.
GAS LINE CONNECTION
GAS CONVERSION
This fireplace is manufactured for use with Natural Gas.
LP Gas conversion kits must be purchased separately.
ATTENTION
CAUTION
The conversion shall be carried out in accordance with the requirements of the provincial authorities having jurisdiction and in
accordance with the requirements of the ANSI Z223.1 installation code.
Installation of the gas line must only be done by a qualified person in accordance with local building codes, if any.
If not, follow ANSI 223.1.
Commonwealth of Massachusetts: Installation must be done by a licensed plumber of gas fitter.
A listed (and Commonwealth of Massachusetts approved) 1/2” (13mm) T-handle manual shut-off valve and flexible gas
connector (included) are connected to the 1/2” (13mm) control valve inlet. If substituting for these components, please consult
local codes for compliance.
This fireplace is equipped with a 3/8”(10mm) x 18” (457mm) long flexible gas connector and manual shut-off valve. The gas
line should be run to the point of connection where the shut-off valve and flexible gas line will connect.
NOTE
The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure
testing of that system at pressures in excess of ½ psi (3.5kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any
pressure testing of the gas line at test pressures equal to or less than ½ psi (3.5 kPa).
For high altitude installations, consult the local gas distributor or the authority having jurisdiction for proper rating methods.
IMPORTANT
The efficiency rating of this appliance is a product of thermal efficiency rating determined under continuous operating
conditions and was determined independently of any installed system.
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) (recommended)
11” WC (2.74 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
13
VENTING
IMPORTANT
Consult the local and national installation codes to assure adequate combustion and ventilation air is available.
Refer to the vent systems manufacturer's installation manual for complete installation instructions.
Installation must conform with the venting requirements and restrictions as outlined in this manual.
APPROVED VENTING
Simpson Dura-Vent DV-GS 5” x 8” direct vent system (horizontal and vertical terminations).
Ameri-Vent Direct Chimney System 5” x 8” (horizontal and vertical terminations).
Selkirk Model DT Direct Vent Chimney Systems 5” x 8” (horizontal and vertical terminations).
Metal Fab Chimney System: 5” x 8” (horizontal and vertical terminations).
Kozy Heat #800-1 series flexible vent system (horizontal terminations).
ICC EXCELDirect Direct Vent Chimney Systems 5” x 8” (horizontal and vertical terminations).
BDM 5” x 8” Direct Vent Chimney System (horizontal and vertical terminations).
This fireplace is designed to be used with any of the above vent systems without the use of an additional adaptor.
RESTRICTOR
IMPORTANT
WE RECOMMEND INSTALLING A RESTRICTOR (INCLUDED IN THE FIREPLACE COMPONENTS PACKET) ON
ALL VERTICAL VENT TERMINATIONS INSTALLED WITHOUT ELBOWS.
Each installation is unique and affected by various factors including venting configuration, altitude and climate. Therefore, after fireplace
installation is complete a restrictor may be required or may need to be removed or modified.
Page 26 has information on restrictor recommendations depending on burner flame appearance and instructions on installation after venting
is completed.
RESTRICTOR INSTALLATION
Large Restrictor
Remove tab (s) to
create small restrictor
Bend tabs to approx. 80 degree
angles to create tension to hold
itself in place when installed.
Slide restrictor into exhaust pipe on top of fireplace with tabs
pointing towards you prior to attaching venting.
Figure 14a
ELBOWS
For each additional 90° elbow used after first elbow, 3ft. (914mm) must be subtracted from maximum allowed venting.
For each 45° elbow used, 1-1/2ft. (457mm) must be subtracted from maximum allowed venting.
NOTE
(2) 45° degree elbows may be used in place of (1) 90° elbow.
14
VENTING
HORIZONTAL VENT SYSTEM CLEARANCES (all approved venting)
TOP
BOTTOM
SIDES
3 inches (76mm)
1 inch (25mm)
1 inch (25mm)
WARNING
KOZY HEAT WALL PASS-THRU, PART #800-WPT 4-1/2” (114mm) - 6-1/2” (165mm) OR
#800-WPT2 (6-1/2” (165mm) - 12-1/2” (318mm) ), MUST BE USED ON ALL HORIZONTAL VENT RUNS.
Horizontal vent shield must be installed when using a 90˚ elbow directly off fireplace to horizontally position vent system.
Horizontal sections require 1/4” (6mm) rise for every 12” (305mm) of travel.
NOTE
HORIZONTAL TERMINATIONS (NAT. GAS)
MINIMUM: 90° elbow + 6” (152mm) horizontal + termination cap.
MAXIMUM: 90° elbow + 10ft. (3.048m) + termination cap.
HORIZONTAL TERMINATIONS (LP GAS)
MINIMUM: 6” (152mm) vertical + 90˚ elbow + 6” (152mm) horizontal + termination cap.
MAXIMUM: 6” (152mm) vertical + 90˚ elbow + 10ft. (3.048m) horizontal + termination cap.
90° Elbow
Min.: 6” (152mm)
Max.: 10ft. (3.048m)
Termination Cap
Figure 15a
Illustration shown with minimum horizontal for NAT. gas.
VERTICAL TERMINATIONS (NAT. & LP GAS)
IMPORTANT
We recommend installing a restrictor (included in components packet) in all vertical terminations installed without elbows.
VERTICAL VENT SYSTEM CLEARANCES
Termination Cap
SIDES
ALL APPROVED VERTICAL PIPE
1 inch (25mm)
MINIMUM:
Ameri-vent, Selkirk, Metal Fab, ICC, BDM vent systems: 4ft. (1.219m)
Simpson Dura-Vent vent system:
8ft. (2.438m)
MAXIMUM: All approved venting systems:
Min.: 4ft. (1.219m) / 8ft. (2.438m)
Max.: 10ft. (3.048m)
35ft. (10.67m)
Figure 15b
15
VENTING
HORIZONTAL & VERTICAL COMBINATION MAXIMUM
MAXIMUM:
10ft. (3.05m) horizontal + 20ft. (6.10m) vertical + cap. 30ft. (9.14m) total.
Figure 16a
CAUTION
This gas appliance must not be connected to or joined with any other chimney flue serving another appliance.
Page 14 has information on restrictor installation in conjunction with venting installation. Page 26 has information on restrictor
recommendations depending on burner flame appearance and instructions on installation after venting is completed.
NOTE
Horizontal sections require 1/4” (6mm) rise for every 12” (305mm) of travel.
For each additional elbow used after first elbow, 3ft. (914mm) must be subtracted from maximum venting allowed. For each 45° elbow
used, 1-1/2ft. (457mm) must be subtracted from maximum venting allowed.
(2) 45° degree elbows may be used in place of (1) 90° elbow.
The horizontal vent heat shield must be installed when using a 90-degree elbow to horizontally position the vent system.
IMPORTANT
Kozy Heat Wall Pass-thru, #800-WPT (4-1/2” (114mm) - 6-1/2” (165mm) wall thickness) or,
#800-WPT2 (6-1/2” (165mm) - 12-1/2” (318mm) wall thickness), must be used on all horizontal vent runs.
16
VENTING
INSTALLATION OF #800-1 SERIES DIRECT VENT TERMINATION KIT(S)
IMPORTANT
The flex pipe is permanently attached to the exterior plate. DO NOT ATTACH #844-1 or #845-1 termination kit to fireplace
(or extension kit) until it has passed through wall. Install termination plates to outside wall exterior.
HORIZONTAL TERMINATIONS Refer to illustration on following page.
IF TERMINATING AGAINST VINYL SIDING, A VINYL SIDING PROTECTOR, INCLUDED WITH #844 AND #845 DIRECT
VENT KITS, MUST BE USED. FOLLOW INSTRUCTIONS INCLUDED.
IMPORTANT
CAUTION
NOTE
The Kozy Heat wall pass-thru, part #800-WPT or #800-WPT2, must be used on all horizontal vent applications regardless of
which vent system you are using.
This gas appliance must not be connected to a chimney flu serving another type of appliance.
Page 14 has information on restrictor installation in conjunction with venting installation. Page 26 has information on restrictor
recommendations depending on burner flame appearance and instructions on installation after venting is completed.
1.
If your vent system application does not require an extension kit, proceed to step #7.
2.
If your vent system application will require one or more extension kits (Part #846-1), proceed with the following steps. Each #846-1
extension kit contains enough 5” & 8” flexible aluminum to extend chimney an additional 6ft. (1.83m).
3.
Gently stretch 5” & 8” flexible aluminum pipes on termination kit (#844-1 or #845-1) and on each extension kit (if used) the length
required for your installation.
IMPORTANT
DO NOT STRETCH EXTENSION KIT BEYOND 6ft. (1.83 m). DO NOT STRETCH BEYOND WHAT IS REQUIRED - IT
IS VERY DIFFICULT TO RECOMPRESS FLEX PIPES ONCE STRETCHED.
4.
Place a bead of sealant outside 5” flex pipe collar (C) (end with EXTERNAL lip), sliding it inside 5” pipe on top of fireplace (D).
Secure with 3 evenly spaced screws.
5.
Place a bead of sealant inside 8” flex pipe collar (E) (end with the INTERNAL lip), sliding it over 8” pipe on top of fireplace (F).
Secure with 3 evenly spaced screws.
6.
If additional extension kits are required, repeat steps #4 - #5, placing 5” & 8” pipes onto previous extension kit.
OPTIONAL: Place insulation between 8” pipe and wall studs.
7.
With spacer legs toward the wall, slide interior firestop (H) over 8” pipe and attach to interior wall (over wall materials).
NOTE
Attachment brackets are included with termination kit. These optional brackets should be screwed or nailed (not provided)
onto top and bottom of 9-1/2” (241mm) H x 9-1/2” (241mm) W opening on exterior of house. The termination plates then fit
between these brackets. Using screws provided, secure brackets to termination box (A). Attach vinyl siding protector (G).
8.
Apply a liberal bead of exterior sealant around outer edge of termination box (A), placing assembly through opening in exterior wall.
Place screws through four slots (B), securing it in place.
9.
Gently pull 5” & 8” pipes down to top of extension kit, or top of fireplace if no extension kits were used.
10. Place a bead of sealant outside 5” flex pipe collar (C) and slide it into 5” pipe on extension kit or top of fireplace (D).
Secure with 3 evenly spaced screws.
ILLUSTRATION ON FOLLOWING PAGE.
17
VENTING
FLEXIBLE #800-1 SERIES cont.
A
TERMINATION BOX
B
SLOTS IN EXTERIOR WALL PLATE
C
5” FLEX PIPE COLLAR
D
5” PIPE ON FIREPLACE OR EXTENSION KIT
E
8” FLEX PIPE COLLAR
F
8” PIPE ON FIREPLACE OR EXTENSION KIT
G
VINYL SIDING PROTECTOR
H
INTERIOR FIRESTOP
G
A
HOT
H
E
C
F
D
Figure 18a
18
B
TERMINATION VENT CAP LOCATION
This gas appliance must not be connected to a chimney serving any other appliance.
1.
2.
3.
Terminations against vinyl siding must use a vinyl siding protector. Follow instructions included.
DO NOT RECESS TERMINATION KIT INTO OUTSIDE BUILDING MATERIALS - i.e.: brick, stone, siding, etc. If necessary,
extend framing so that termination kit will be exposed once building materials are installed.
Vent termination must not be located where it will become plugged by snow or other material. The flow of combustion and ventilation
air must be not obstructed.
LOCATION CLEARANCES
A. Above grade, veranda, porch, deck, balcony - 12" (305mm).
B. Operable window or door - CANADA: 12" (305mm). US: 9” (229mm).
C. Permanently closed window* - 12" (305mm) (Recommended to prevent condensation on window).
D. Ventilated soffit* ** - 24" (610mm).
E. Unventilated soffit* **- 12" (305mm).
F. Outside corner* - 3" (76mm).
G. Inside corner* - 3” (76mm).
H. Meter / Regulator: CANADA: Not to be installed above a gas meter/regulator assembly within 3ft. (914 mm) horizontally from the
centerline of the regulator within a height of 15ft. (4.57m). US*.
I. Gas Service regulator vent outlet - CANADA 3ft. (914mm). US*.
J. Non-mechanical air supply inlet to building or the combustion air inlet to any other appliance. CANADA: 12" (305mm).
US: 9” (229mm).
K. Mechanical air supply inlet. CANADA: 6ft. (1.83m) US: 3ft. (914mm) above if within 10ft. (3.05m) horizontally.
Massachusetts installations: 10ft. (3.05m).
L. Above paved side-walk or paved driveway located on public property - 7ft. (2.13m).
NOTE
A vent cannot be located directly above a side-walk or paved driveway that is located between two single family dwellings and
serves both dwellings.
M. Under veranda, porch, deck, or balcony (must be fully opened on a minimum of 2 sides)** - 12" (305mm).
N. Between two horizontal terminations - 12" (305mm).
O. Between two vertical terminations - 12" (305mm). Terminations may be same height.
P. Above furnace exhaust or inlet - 12" (305mm).
*Clearance must be in accordance with local installation codes & the requirements of the gas supplier.
**VINYL SOFFIT / VINYL CEILING / VINYL OVERHANG DISCLAIMER
Clearances to heat resistant material (i.e. wood, metal). This does not include vinyl. Hussong Manufacturing Co., Inc. will not be held responsible for heat
damage caused from terminating under vinyl overhangs, vinyl ceilings or vinyl ventilated/unventilated soffits.
Denotes where installation not allowed
Figure 19a
19
VENTING
(Vertical Cap Requirements)
VENT TERMINATION CLEARANCES
Roof Pitch
H (Min.) Ft.
H (Min.) m
Flat to 6/12
1.0
0.30
Over 6/12 to 7/12
1.25
0.38
Over 7/12 to 8/12
1.5
0.46
Over 8/12 to 9/12
2.0
0.61
Over 9/12 to 10/12
2.5
0.76
Over 10/12 to 11/12
3.25
0.99
Over 11/12 to 12/12
4.0
1.22
Over 12/12 to 14/12
5.0
1.52
Over 14/12 to 16/12
6.0
1.83
Over 16/12 to 18/12
7.0
2.13
Over 18/12 to 20/12
7.5
2.27
Over 20/12 to 21/12
8.0
2.44
CAUTION
This appliance must not be connected to or joined with any chimney flue serving any other appliance.
Approved Cap
Discharge opening
Minimum
*8ft. (2.44m)
Approved vent pipe
H
X
12
Roof pitch = X/12
H - Minimum height from roof to lowest discharge opening
* If vent is closer than 8ft. (2.44m), it must terminate at least
2ft. (0.61m) higher than any portion of a building within 10ft.
(3.05m) of the vent.
Figure 20a
20
PIER CONVERSION INSTRUCTIONS
1.
Remove screws and top bracket from top of non-vented end of fireplace.
2.
Lift end panel up and off mounting studs located along top and bottom sides of pier end frame.
3.
Remove nuts (4) securing valance at top and bottom.
4.
Remove valance.
5.
Remove bottom refractory panel located in front of pier end refractory panel.
6.
Remove pier end refractory panel.
7.
Re-install bottom refractory panel.
#3
#1
#4
#5
#6
#2
Figure 21a
OPTIONAL
IF DESIRED, SCREEN INSTALLED IN GLASS FRAME ASSEMBLY INCLUDED WITH KIT MAY BE REMOVED.
8.
Attach glass frame assembly, included with pier conversion kit, securing with nuts (4) removed in step 3.
9.
Position hooks on frame, included with kit, over mounting studs located along top and bottom sides of pier end frame.
10. Attach upper hood, included with kit, into upper hood clips.
#10
#8
#9
Figure 21b
21
#TMT-500 LOG SET INSTALLATION
ATTENTION
NOTE
CAUTION
If converting to LP (propane) gas do so now before installing log set. Follow instructions included with conversion kit.
Logs are installed in numerical order. Log numbers are located on bottom of each log. Refer to following instructions and
illustrations for proper placement.
Do not place logs directly over burner port holes. Improper log placement may affect flame appearance and cause excessive
soot to build up on logs and glass.
TM3
TM2
TM1
TM2
TM3
Position base logs #TM1, (2) #TM2, & (2) #TM3 onto burner, aligning holes in log bottoms to mounting studs in burner cover.
Use a steel or stiff bristle nylon brush to distribute Rock Wool Embers onto logs and burner.
Figure 22a
TM5
TM4
TM4
TM5
Position (2) #TM4 and (2) #TM5 logs, aligning to corresponding notches in base logs.
Figure 22b
22
LOG SET INSTALLATION
TM7
TM6
TM6
TM7
Position (2) #TM6 and (2) #TM7 logs, aligning to notches in base logs.
Figure 23a
Use a steel or stiff bristle nylon brush to distribute Rock Wool Embers onto logs and burner.
Figure 23b
23
CONTROL BOARD REMOVAL / INSTALLATION
CAUTION
NOTE
If burner and/or pilot have been burning, use appropriate protection to avoid burns or damage to personal property before
removing any components.
Illustrations shown with TMT-3875 valve components.
REMOVAL
1.
Turn fireplace off.
2.
Shut off gas supply at the manual shut-off valve.
3.
Disconnect gas line flex tube from the manual shut-off valve.
4.
Disconnect any wall switch, remote control or thermostat wires from
top & bottom terminals on the gas valve or unplug all components from
receptacle, disconnect all wiring harnesses attached to gas valve.
5.
Remove upper hood, upper louver & glass assembly.
6.
Remove logs, pilot shield, pilot plate and ember / log refractory panels.
7.
Remove screws securing front left and right rear burner legs. Remove
burner assembly.
8.
Remove adjustable venturi spacers.
9.
Remove (8) screws securing control board to firebox bottom. (Front (3)
screws can be accessed through holes in burner heat shield).
ACCESS HOLES
PILOT
PLATE
10. Lift control board up and out of firebox being careful not to damage
sealing gasket lying underneath.
PILOT
BURNER ASSEMBLY
INSTALLATION
1.
Place control board in firebox, aligning holes in control board with
holes firebox bottom. MAKE SURE SEALING GASKET IS IN
PLACE ON FIREBOX BOTTOM! Secure to firebox bottom with (8)
screws previously removed.
2.
Reinstall burner assembly, securing with screws previously removed.
3.
Reinstall pilot plate, securing with screws previously removed.
4.
Reinstall pilot shield.
5.
Reinstall ember/log refractory.
6.
Reinstall log set. Pages 22-23.
7.
Reconnect gas line to manual shut-off valve.
8.
Reconnect any wall switch, remote control or thermostat wires to top &
bottom terminals on gas valve or re-connect all wiring harnesses to gas
valve. Plug all components into electrical outlet.
9.
VENTURI SPACERS
RE-CONNECT REMOTE / THERMOSTAT WIRES
Reinstall glass frame assembly. Page 12.
10. Reinstall upper louver, upper hood and lower grill. Page 25.
11. Turn gas on. Check for leaks at all connections with soapy water,
whether field or factory made.
12. Verify proper log placement, operation of fireplace, and any electrical
components.
24
Figure 24a
GRILL SET
INSTALLATION
Slide flange on upper hood into
clips at top of upper air passage.
Upper hood clips
Figure 25a
Thread screws into nut at each end of
grill. Secure to lower grill opening.
1.
Align hooks in upper louver to slots located in fireplace face. Set down into position.
2.
Insert upper hood flange into clips located at top of upper air passage, keeping in mind this is a fairly tight fit.
3.
Partially thread (2) screws (included in components packet) into nuts at each end of lower grill. Secure to fireplace by threading
screws into corresponding holes in inside flange of lower grill opening. The lower grill can now be opened and closed to access gas
valve and controls.
REMOVAL
1.
Use both hands to pull hood out of upper air passage clips.
2.
Lift upper louver up and out of slots.
3.
Remove screws securing lower grill at each end to remove from fireplace.
25
FINALIZING THE INSTALLATION
RESTRICTOR USAGE:
Turn fireplace on and allow to burn for 15 minutes.
If flames indicate there is excessive draft (flickering, short flames), a restrictor may be necessary.
If flames indicate insufficient draft (lifting or ghosting flames), a previously installed restrictor may need to be modified or removed.
WARNING
TO AVOID PROPERTY DAMAGE OR PERSONAL INJURY, ALLOW FIREPLACE AMPLE TIME TO COOL BEFORE MAKING ANY
ADJUSTMENTS AND / OR INSTALLATIONS.
RESTRICTOR TROUBLESHOOTING
FLAME APPEARANCE
DRAFT PROBLEM
RESTRICTOR SOLUTION
Short, flickering
Excessive draft - not enough restriction
Add restrictor
Lifting or ghosting*
Insufficient draft - too much restriction
Remove inner ring (s) on restrictor or
remove restrictor
* Improper venting installation may cause flames to lift or “ghost” - a dangerous situation. Inspect flames after installation to ensure proper
performance. If determined that venting is correct, and the restrictor has been removed, yet flames are still lifting or ghosting, shut off gas
supply to fireplace and call a qualified service technician.
RESTRICTOR INSTALLATION / MODIFICATION (after termination completion):
If it is determined that a restrictor is needed or restrictor modification is required after termination is installed, access can be reached
through the fireplace baffle. Please remove logs and refractory to avoid damaging these components.
1.
Remove (2) screws securing baffle. Remove baffle to expose venting. (A flat head screwdriver may be helpful to release from flange).
2.
Depending on your specific needs, determined by chart above along with other factors, make necessary modifications.
3.
If installation of a restrictor (included in fireplace components packet) is necessary, bend tabs on restrictor to approx. 80 degree angles
to create tension when inserted into exhaust pipe on fireplace. Insert restrictor into 5” exhaust pipe with tabs pointing towards you.
4.
If modification is necessary, remove restrictor by pulling it down and out of 5” exhaust pipe.
5.
Reinstall baffle by resting baffle side above flange along inside top of firebox opening. Use a flat head screwdriver to help insert into
opposite flange. Secure with (2) screws previously removed.
6.
Reinstall refractory and log set.
7.
Attach glass frame assembly and light fireplace. Wait 15 minutes before determining if any further modifications are necessary.
Remove tab (s) to
create small restrictor
FLANGE
BAFFLE
Large
Bend tabs to approx. 80 degree angles
to create tension to hold itself in place
when installed.
Slide restrictor into exhaust pipe at
top of fireplace with tabs pointing
towards you.
Figure 26a
26
FINALIZING THE INSTALLATION
FLAME APPEARANCE:
Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi setting has
been factory set, adjustments may be necessary for optimal performance and visual aesthetics.
When fireplace is first lit, the flames will be blue. Flames will gradually turn yellowish-orange during first 15 minutes of operation. If
flames remain blue, or become dark orange with evidence of sooting (black tips), the burner tube venturi may need adjustment.
Short blue flames
venturi open too far
Lazy yellow flames - ideal
Correct pilot flame
Dark orange flames / black tips
Venturi closed too far
Excessive burner media
Figure 27b
Figure 27a
WARNING
Lifting (ghosting) flames
Improper Venting
Gas pressure too high
Burner tube adjustable venturi positioning should only be performed by a qualified professional service technician.
FACTORY SET BURNER TUBE VENTURI SETTINGS
(ADJUST AS NECESSARY FOR YOUR INSTALLATION)
NATURAL GAS
LP (PROPANE) GAS
5/8” (16mm) open
1/8” (3mm) open
BURNER TUBE VENTURI ADJUSTMENT GUIDELINES
VENTURI POSITION
FLAME COLOR
VENTURI ADJUSTMENT
Closed too far
Dark orange flame with black tips
Open venturi setting slightly
Open too far
Blue flames
Close venturi setting slightly
NOTE
IMPORTANT
If soot is present, check log positioning before adjusting burner venturi. Logs must not block burner ports.
SL I GHT AD J U STM EN T S T O BU R N ER VE N TU RI OP EN IN G CR E A TE D R AM A TI C R E SU LT S. A D J U ST AT SL I G HT
INCREM ENT S UNTIL DESI RED LOOK IS ACHI EVED. AL WAY S BURN FIREPLAC E FOR AT LEAST 15 M INUTES
AND ALLOW TIME TO COOL BEFORE MAKING ANY FURTHER ADJUSTMENTS.
TO ADJUST VENTURI:
Burner venturi adjustment handle is attached to underside of control board. Access through lower grill opening. Loosen wing nuts, adjust
as necessary, pulling handle forward to open, pushing backwards to close. Tighten wing nuts.
Figure 27c
27
MAINTENANCE
The appliance is required to be inspected at least once a year by a professional service person.
The compartment below firebox must be cleaned at least once a year, more frequent cleaning may be required due to excessive lint from carpeting,
bedding materials, or other fibrous materials. Use a vacuum to clean all components at least once a year.
NOTE
INSTALLATION AND REPAIR SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE
INSPECTED BEFORE USE AND ANNUALLY BY A QUALIFIED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE
REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIALS, ETC. IT IS IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS AND CIRCULATION AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN .
CONTROL BOARD SYSTEM
Annual cleaning of burner system is required. Vacuum all components thoroughly.
The burner assembly may be removed for easier access. Refer to page 24 in this installation manual for complete instruction on removing &
reinstalling burner assembly.
Visually check for blocked port holes, especially near the pilot. Blocked port holes may cause delayed ignition.
Reinstall burner assembly following instructions on page 24 of this installation manual.
Visually check pilot light and burner when in operation. Flames should be steady, not lifting or floating.
Figure 28a
TMT-3875 Pilot
TMT-3875-MV Pilot
TMT-3875-IPI Pilot
Burner Orifice
Burner Ports
FAN
The fan should be disconnected from electrical current, and cleaned (vacuumed) every six months. The bearings are sealed and require no oiling.
VENT SYSTEM
Annual examination of venting system by a qualified agency is required.
IF VENT-AIR INTAKE SYSTEM IS DISASSEMBLED FOR ANY REASON, RE-INSTALL PER INSTRUCTIONS PROVIDED WITH INITIAL
INSTALLATION.
The flow of combustion and ventilation air must not be obstructed.
GLASS CLEANING & REPLACEMENT
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH GLASS/FRAME ASSEMBLY REMOVED, CRACKED OR BROKEN. REPLACEMENT OF THE
GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR QUALIFIED SERVICE PERSON.
Use protective gloves to handle any broken or damaged glass assembly components.
The glass assembly, part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
Replacement of glass & frame assembly, part #TMT-057T, must only be performed by a licensed or qualified service person.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass door assembly.
IMPORTANT
CAUTION
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
KEEP APPLIANCE AREA CLEAR OF COMBUSTIBLE MATERIALS, SUCH AS GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.
28
LIMITED WARRANTY
KOZY HEAT LIMITED 10 YEAR WARRANTY
This limited 10 Year Warranty will not become effective until the Warranty Registration Form has been completed and mailed to
Hussong Manufacturing Co., Inc., P.O. Box 577, Lakefield, MN 56150. This registration form must be received within 30 days of
installation. Failure to do so may result in delayed warranty coverage and submission of proof of purchase will be required.
Hussong Manufacturing Co., Inc. warranties to the original purchaser of this Kozy Heat Fireplace, that it is free of defects in materials
and workmanship at the time of manufacture.
Subject to the following conditions & requirements, Hussong Manufacturing Co., Inc. extends the following limited warranty under
normal use and service, with respect to the Kozy Heat line of gas burning fireplaces.
YEAR 1: Subject to the conditions & requirements listed below, within the first year from date of purchase, Hussong Manufacturing Co.,
Inc. shall, at its discretion, replace or repair any such defect in material or workmanship, at Hussong Manufacturing Co., Inc.’s expense,
including reasonable labor costs to repair or replace the defective component, if a factory pre-authorization is given for the repair.
YEARS 2-10: Subject to the conditions & requirements listed below, beginning with the first day of the second year and continuing
through the tenth year, Hussong Manufacturing Co., Inc., will at its discretion, provide repair or replacement parts at current list prices
for any defect in material or workmanship of components, including optional components and accessories (if available). Husson g
Manufacturing Co., Inc. shall not be responsible for any installation, labor, transportation of other indirect costs.
LIMITATION OF LIABILITY
To make a claim under this warranty, the purchaser must first contact the dealer/installer from whom the fireplace was purchased.
This limited warranty will be void if the fireplace is not installed by a qualified installer and according to the installation instructions.
Use of unauthorized components will make this warranty null and void.
This limited warranty also is void if the fireplace is not operated, at all times, according to the operating instructions fu rnished.
This warranty is limited to defects in material and workmanship. It does not apply to any product that has been subject to negligence,
misapplication, improper installation.
No person is authorized to extend the time of this warranty or to accept on Hussong Manufacturing Co., Inc.’s behalf any additional
obligation of liability connected with the unit.
It is expressly agreed and understood that this warranty is Hussong Manufacturing Co., Inc.’s sole obligation and purchaser’s exclusive
remedy for defective fireplace equipment. Hussong Manufacturing Co., Inc. shall not be liable for any consequential, incident al or
contingent damages whatsoever. The foregoing warranty is exclusive and in lieu of all other expressed warranties. Hussong
Manufacturing Co., Inc. shall not be held to implied warranties or merchantability and fitness for a particular purpose. This warranty
replaces all previous warranty policies.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Hussong Manufacturing Co., Inc. reserves the right to make changes at any time, without notice, in design, material, specifications and
prices. Hussong Manufacturing Co., Inc. reserves the right to discontinue models and products.
WARRANTY CONDITIONS & REQUIREMENTS:
1.
2.
3.
4.
5.
6.
You are the original purchaser. This warranty is not transferable.
Installation of the fireplace is performed by a qualified installer.
Installation and operation must comply with installation and operation instructions.
Paint and glass gaskets are covered for 30 days from date of purchase.
Remote controls and all optional accessories are covered for 1 year from date of purchase.
This warranty does not offer coverage for Light Bulbs or Batteries (whether factory, dealer or installer supplied). This includes any
damage stemming from either component’s nonuse.
7. Components broken, (including glass panels), during shipping, careless handling of components, or defects resulting from improper
installation, misuse of the fireplace and components are not covered under this warranty.
8. This warranty does not cover any part of the fireplace or any components which have been exposed to or submerged under water.
9. Hussong Manufacturing Co., Inc. must be notified by the dealer the fireplace was purchased from or a qualified installer/service
technician of the defect.
10. Annual service of the fireplace as required in the installation manual, is performed by a qualified installer/service technician.
(Copies of such service records may be required to claim a warranty).
11. All previous warranty/service has been performed by a qualified installer or service technician.
(Copies of such service records may be required to claim a warranty).
Effective September 01, 2011
29
LIFETIME WARRANTY
LIFETIME WARRANTY
THIS LIFETIME WARRANTY COVERAGE WILL BE EXTENDED AS DESCRIBED BELOW PROVIDED ALL WARRANTY
CONDITIONS AND REQUIREMENTS ARE MET AS OUTLINED IN THE 10 YEAR LIMITED WARRANTY POLICY.
LIFETIME WARRANTY COVERAGE
LIFETIME WARRANTY IS EXTENDED AS FOLLOWS: Hussong Manufacturing Co., Inc. warranties to the original purchaser that the
firebox, heat exchanger, fiber logs, burner tube and glass panel of this Kozy Heat Fireplace will not be defective in materia l or
workmanship under normal use and service for as long as you own this product. If any of these components fail due to defects in material
and workmanship under normal use and service, Hussong Manufacturing, Co., Inc. will, at its sole discretion, repair or replace the defective
component. This LIFETIME WARRANTY does not cover any installation, labor, transportation or other indirect cost arising from
defective components.
LIMITATION OF LIABILITY
This Lifetime Warranty will be void if the fireplace is not installed by a qualified installer and according to the installation instructions.
Use of unauthorized components will make this warranty null and void. This Lifetime Warranty also is void if the fireplace is not operated,
at all times, according to the operating instructions furnished. This warranty is limited to defects in material and workmans hip of
components specified. It does not apply to any product that has been subject to negligence, misapplication, improper installa tion.
No person is authorized to extend the time of this Lifetime Warranty or to accept on Hussong Manufacturing Co., Inc.’s behalf any
additional obligation of liability connected with the unit .
Hussong Manufacturing Co., Inc. may fully discharge all obligations with respect to this Lifetime Warranty by refunding the wholesale
price of the defective component(s).
It is expressly agreed and understood that this Lifetime Warranty is Hussong Manufacturing Co., Inc.’s sole obligation and original
purchaser’s exclusive remedy for defective fireplace equipment. Hussong Manufacturing Co., Inc. shall not be liable for any
consequential, incidental or contingent damages whatsoever other than those incurred by Hussong Manufacturing Co., Inc. to repair or
replace the defective component. The foregoing warranty is exclusive and in lieu of all other expressed warranties. Hussong Manufacturing
Co., Inc. shall not be held to implied warranties, including but not limited to the implied warranties or merchantability and fitness for a
particular purpose. This lifetime warranty replace all previous lifetime warranty policies.
Hussong Manufacturing Co., Inc. reserves the right to make changes at any time, without notice, in design, material, specifications and
prices. Hussong Manufacturing Co., Inc. reserves the right to discontinue models and products.
To activate this Lifetime Warranty coverage, this registration card must be completed and mailed with your completed 10 Year
Limited Warranty form within 30 days of installation to the following address:
Hussong Manufacturing Co., Inc.
P.O. Box 577
204 Industrial Park Drive
Lakefield, MN 56150-0577
Sept. 2011
CUT ALONG DOTTED LINE
PURCHASER NAME:
INSTALLATION DATE:
ADDRESS:
MODEL #:
SERIAL #:
TELEPHONE:
INSTALLER NAME:
ADDRESS:
TELEPHONE:
30
Supplemental Installation and Homeowner
Information Manual for Trimont Model:
SEE-THRU DIRECT VENT GAS FIREPLACE
English and French Installation Manuals Available Through Your Local Dealer or Visit Our Website at www.kozyheat.com
Les manuels d’installation en anglais et en français sont disponibles chez votre détaillant local ou en visitant notre site Web : www.kozyheat.com
IMPORTANT:
This supplemental installation and homeowner manual is to be used in
conjunction with TRIMONT INSTALLATION MANUAL. Read both manuals before installing and
operating appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This appliance may be installed in an aftermarket permanently located,
manufactured home (USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.
—Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
◙ Do not try to light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
◙ If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
Rapport no 216-F-13b-6.5
APRIL 2013
TMT-3875-SUP-REV-03
www.kozyheat.com
TABLE OF CONTENTS
SAFETY INFORMATION
Safety Information
2
SPECIFICATIONS
Components List
3
Gas Pressure Requirements / BTU’s
3
FAN INSTALLATION
TMT-028 Optional Fan Installation
4
THERMOSTAT / WALL SWITCH / REMOTE
Thermostat / Wall Switch / Remote
5
OPERATING INSTRUCTIONS
Valve and Pilot Assembly Components
Lighting and Shutdown Instructions
Pressure Testing
6
7-9
10
TROUBLESHOOTING
Troubleshooting
11-13
CONVERSION KIT INSTRUCTIONS
Conversion Kit Instructions
14-16
MAINTENANCE
Maintenance
17
REPLACEMENT PARTS
Replacement Parts
18
1
SAFETY INFORMATION
This fireplace has been tested by OMNI-Test Laboratories, Portland, Oregon and complies with:
ANSI Z21.88-2009/CSA 2.33-2009, “Standard for Vented Gas Fireplace Heaters.”
CAN/CGA 2.17-M91 (R2009), “Gas-Fired for Use at High Altitudes.”
CAN/CSA P.4.1-09, “Testing Method for Measuring Annual Efficiency”.
This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation Code, CSA B149.1
Installation and repair should be done only by a qualified service person. The appliance should be inspected by a
qualified service person before use. Annual inspection by a qualified service person is required to maintain warranty.
More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulation air passageways of the appliance be kept clean.
If this appliance is installed directly on carpeting, tile or other combustible material other than wood flooring, the
appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at
risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other flammable material should not be placed on or near the appliance.
Adequate accessibility clearances for servicing and proper operation must be maintained.
This appliance must not share or be connected to a chimney flue serving any other appliance.
Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor and liquids.
The flow of combustion and ventilation air must not be obstructed.
Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.
The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance.
Work should be done by a qualified service technician.
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH THE GLASS/FRAME ASSEMBLY REMOVED, CRACKED
OR BROKEN. REPLACEMENT OF THE GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR
QUALIFIED SERVICE PERSON .
The glass assembly, Part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass assembly.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance.
Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this appliance.
Keep burner and control compartment clean.
Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect this
appliance and to replace any part of the control system and any gas control which has been under water.
2
SPECIFICATIONS
#TMT-3875 COMPONENTS LIST
PART NUMBER
DESCRIPTION
TMT-770
Millivolt Board Assembly
700-203
Manual Gas Shut-off Valve
TMT-135
Burner Assembly
TMT-I900
Refractory set
TMT-500
Log Package
TMT-057T
Glass Frame Assembly
600-083
Receptacle / Speed Control Assembly
942-085
5” Restrictor Plate
500-TRF
3 pc. Grill Assembly (2 sets)
TMT-3875
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) (recommended)
11” WC (2.74 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.8” WC (.95 kPa)
10” WC (2.49 kPa)
MANIFOLD PRESSURE (LO)
1.1” WC (.27 kPa)
6.3” WC (1.57 kPa)
ORIFICE SIZE
#30
#45
INPUT BTU/hr. (kW)
47,000 (13.77 kW)
46,000 (13.48 kW)
MINIMUM INPUT BTU/hr. (kW)
23,500 (6.89 kW)
35,500 (10.4 kW)
3
OPTIONAL FAN INSTALLATION
INSTALLATION OF THIS FAN SHOULD BE DONE ONLY BY A QUALIFIED INSTALLER
MAKE SURE HOUSEHOLD BREAKER IS SHUT OFF PRIOR TO WORKING ON ANY ELECTRICAL LINES.
WARNING
IMPORTANT
THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR PROTECTION AGAINST SHOCK HAZARD AND
SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT CUT OR REMOVE
GROUNDING PRONG FROM THIS PLUG.
If installing a fan, it is easier to complete prior to connecting millivolt board to gas supply. Wiring must be done before enclosing fireplace sides.
An electrical box and romex connector are pre-installed on a removable panel on right side of fireplace. A receptacle / speed control assembly and
(3) wire nuts are included in fireplace components packet.
Code approved line voltage wiring 14 gauge or better must be used when wiring this assembly.
Refer local electrical codes for specific requirements.
NOTE
This appliance must be electrically grounded and connected in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 Current Edition, or the Canadian electrical Code CSA C22.1.
This fan will not operate unless speed control has been turned ON and sufficient heat has been applied to temperature control switch. The fan will
turn ON and OFF automatically as fireplace heats and cools. Adjust fan to desired speed while it is running.
Optional fan kit #TMT-028 includes:
(1) 75 CFM fan with temperature control switch and 4ft. (1219mm) fan cord
(2) 1/4” nuts
1.
Remove upper hood, upper louver & lower grill, if installed.
2.
Remove glass assembly.
3.
Insert fans through lower grill opening on left side of gas valve. Align mounting slots in fan brackets with mounting studs on vented of
fireplace. Secure with nuts.
4.
From inside lower right grill opening, loosen screw securing removable access panel (with electrical box & romex connector installed).
Remove panel.
5.
Insert 115V wiring (with ground) through romex connector and wire to speed control / receptacle assembly matching black (hot), white
(neutral), and green (ground) wires to corresponding wires on speed control / receptacle assembly.
6.
Secure speed control / receptacle assembly to electrical box with (2) screws provided.
7.
Re-install electrical access panel. Tighten screw.
8.
Attach temperature control switch to bottom of firebox.
9.
Plug cord into electrical box receptacle.
10. Turn speed control counter-clockwise until it ‘clicks’. This is the OFF position.
11. Turn speed control ON by turning knob clockwise past the ‘click’ - this is the highest setting.
12. Re-install glass assembly, lower grill, upper louver & upper hood.
Temperature Switch
Electrical Box
Incoming wiring60Hz
110V-120V
TEMPERATURE CONTROL SWITCH POSITION
Before adjusting temperature control switch, unplug 3-prong plug
on fan cord from receptacle. Adjust position of temperature
control switch to a warmer location under firebox to turn fan ON
sooner or move it to a cooler location under firebox to turn fan
ON later. The fan will turn on when sensor in temperature control
switch reaches 110° F and will turn OFF when sensor reaches 90°
F. After adjustment, insert fan cord 3-prong plug into receptacle.
Speed Control
Receptacle Assembly
Figure 4a
4
THERMOSTAT / WALL SWITCH / REMOTE
If desired, a thermostat (wireless style also available), wall switch, or remote control assembly may be used to turn fireplace OFF and ON.
Only ONE of these may be installed. Follow instructions included with chosen assembly.
NOTE
INSTALLATION OF THERMOSTAT OR WALL SWITCH SHOULD ONLY BE PERFORMED BY A QUALIFIED INSTALLER .
CAUTION
DO NOT CONNECT HIGH VOLTAGE (115V) WIRE TO THE GAS VALVE!
Remote Control Wiring Diagram
Thermostat Wiring Diagram
OPTIONAL
Disconnect ON/OFF rocker switch
wires from back of gas valve.
Figure 5a
WALL SWITCH / THERMOSTAT:
Run low-voltage (thermostat) wires from terminals on gas valve to desired location of wall switch or thermostat.
Attach appropriate connectors to wall switch / thermostat wires and connect to top and bottom terminals marked TH/TPTH on gas valve.
REMOTE CONTROL:
Follow instructions included with remote control.
If ON/OFF rocker switch wires are not disconnected, the ON/OFF rocker switch on millivolt board must be in OFF position for
proper operation of any of these components.
IMPORTANT
If rocker switch is ON, fireplace burner will operate until it is turned OFF by rocker switch. A wall switch, thermostat, or
remote control will not turn fireplace OFF when it has been turned ON by the rocker switch.
NOTE
Fireplace must be turned ON and OFF by same method. For example: If fireplace is turned ON by remote control, it must be
turned OFF by remote control.
IMPORTANT
The insulated cover included with remote control must be placed over remote receiver to prevent overheating.
5
VALVE & PILOT ASSEMBLY COMPONENTS
THERMOPILE
PILOT HOOD
ELECTRODE
THERMOCOUPLE
PIEZO IGNITOR
GAS CONTROL KNOB
HI /LO FLAME ADJUSTMENT KNOB
ON/OFF ROCKER SWITCH
VALVE TERMINALS
Figure 6a
6
LIGHTING AND SHUTDOWN
FOR YOUR SAFETY - READ BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
DUE TO HIGH SURFACE TEMPERATURES, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
A.
This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B.
BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in, or turn by hand, do not try to
repair it, call a qualified service technician. Forced or attempted repair may result in a fire or explosion, and loss of war ranty.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system which has been under water.
WARNING
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.
WARNING
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES AND
SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE. CLOTHING OR OTHER FLAMMABLE
MATERIAL MUST NOT BE PLACED ON OR NEAR THE APPLIANCE.
A PAINT SMELL WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING. IT IS RECOMMENDED TO LEAVE
THE FAN OFF DURING THIS PERIOD TO HEL P SPEED THE PAINT CURING PROCESS.
NOTE
THIS FIREPLACE MAY PRODUCE NOISES OF VARYING DEGREES AS IT HEATS AND COOLS DUE TO METAL
EXPANSION AND CONTRACTION. THIS IS NORMAL AND DOES NOT AFFECT THE PERFORMANCE OR
LONGEVITY OF THE FIREPLACE.
7
LIGHTING AND SHUTDOWN (cont.)
LIGHTING INSTRUCTIONS
1.
Set thermostat to lowest setting, if installed.
2.
Turn off all electrical power to appliance. (Fan).
3.
Open lower grill to access gas valve & controls.
4.
Push gas control knob in slightly and turn clockwise to OFF.
5.
Wait five (5) minutes to clear out any gas. Then smell gas,
including near the floor. If you then smell gas, STOP!
Follow WHAT TO DO IF YOU SMELL GAS safety
information below. If you don’t smell gas, go to next step.
5 MINUTES
PILOT
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch; do not use the phone in your
building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
PILOT
TUBE
If you cannot reach your gas supplier, call the fire department.
NOTE
Gas control knob cannot be turned from PILOT
to OFF unless knob is pushed in slightly.
Do not force.
6.
Locate pilot - follow metal tube from gas control. (Located
inside combustion chamber).
7.
Push gas control knob on gas valve in slightly and turn
counterclockwise to PILOT.
8.
Push valve knob in and hold while repeatedly pressing piezo
igniter button until pilot is lit while continuing to hold in gas
control knob.
9.
1 MINUTE
Hold gas control knob in for one (1) minute after pilot is lit.
Release gas control knob. If pilot goes out, repeat steps 4-8.
When pilot is lit, proceed to step 10.
CAUTION
If knob does not pop up when released, stop and
immediately call your service technician or the
gas supplier. If pilot will not stay lit after
several tries, turn gas control knob to OFF
and call your service technician or gas supplier.
10. Push gas control knob in slightly and turn counterclockwise
to ON. The burner can now be turned ON by depressing
ON/OFF rocker switch located beside valve, or wall switch,
OR by setting thermostat or remote control to desired
setting.
11. Turn on all electric power to appliance (if applicable).
NOTE
When fireplace is initially lit, condensation will
appear on the glass; this is normal in all gas
fireplaces and will disappear after several
minutes.
Figure 8a
8
LIGHTING AND SHUTDOWN (cont.)
TO TURN OFF GAS TO APPLIANCE
TURN BURNER OFF
To turn burner OFF, depress ON/OFF rocker switch to OFF, turn off wall
switch or adjust setting on thermostat or remote control.
NOTE
The pilot will stay lit.
TURN PILOT OFF
Turn pilot off by pushing in and turning gas control knob to OFF.
DO NOT FORCE.
NOTE
This control valve has an interlock device. If pilot has been
turned off, it cannot be relit until thermocouple has cooled,
(approximately 60 seconds).
Figure 9a
ADJUSTING FLAME HEIGHT
The gas control valve has a HI /LO flame adjustment knob designed to allow
you to tailor the look and heat output of your fireplace. Adjust by turning
middle knob on gas control valve.
Figure 9b
Figure 9c
9
PRESSURE TESTING
IMPORTANT
Pressure check taps for manifold (outgoing) and inlet (incoming) pressure have been incorporated into the valve. The pressure
tap marked OUT measures outgoing pressure and pressure tap marked IN measures incoming pressure. Follow instructions
below for proper testing procedures. Refer to page 15 for proper NAT and LP manifold pressures.
The appliance and its individual shutoff valve must be disconnected from gas supply piping system during any pressure testing
of that system at pressures in excess of ½ psi (3.5 kPa).
NOTE
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any
pressure testing of the gas line at test pressures equal to or less than ½ psi (3.5 kPa).
INLET PRESSURE TEST:
1.
Loosen inlet (IN) pressure tap screw (counter-clockwise).
2.
Attach manometer using a 5/16” I.D. hose.
3.
Light pilot.
4.
Turn gas control knob to ON (burner should not light). Note manometer reading.
5.
Press rocker switch to ON. Check pressure to ensure it stays near maximum inlet pressure.
6.
Press rocker switch to OFF.
7.
Turn gas control knob to OFF.
8.
Disconnect hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
9.
Relight pilot and turn gas control knob to ON. Reattach manometer to inlet pressure tap to verify it is completely sealed.
Manometer should read no pressure.
NOTE
If inlet pressure reading is too high or too low, contact the gas company. Only a qualified gas service technician should adjust
the incoming gas pressure.
MANIFOLD PRESSURE TEST:
1.
Light pilot.
2.
Loosen manifold (OUT) pressure tap screw (counter-clockwise).
3.
Attach manometer to pressure tap using a 5/16” I.D. hose.
4.
Turn gas control knob to ON.
5.
Press rocker switch to ON and note manometer reading.
6.
Press rocker switch to OFF.
7.
Disconnect manometer hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
8.
Attach manometer to manifold pressure tap to verify it is completely sealed. Manometer should read no pressure when rocker switch is
pressed to ON.
CAUTION
A LOW PRESSURE READING CAN CAUSE DELAYED IGNITION.
MANIFOLD
INLET
Figure 10a
10
TROUBLESHOOTING
CAUTION
THE FOLLOWING MUST BE PERFORMED BY A QUALIFIED TECHNICIAN.
NO SPARK FROM ELECTRODE TO PILOT WHEN PIEZO BUTTON IS TRIGGERED.
A. Check wiring at back of piezo for proper connection.
B. Check wiring at electrode for proper connection.
C. Check position of electrode (1/8” (3mm) between electrode and pilot). Readjust if necessary.
D. Look for arc below electrode and along electrode wire. Direct metal contact may cause an arc below electrode.
SPARK IGNITER WILL NOT LIGHT AFTER REPEATED TRIGGERING OF PIEZO BUTTON.
A. No gas or low gas pressure.
♦ Check remote shut off valves from fireplace. Usually there is a valve near the main. There may be more than (1) valve between
the fireplace and the main.
♦ Low gas pressure can be caused by several situations such as a bent line, too narrow diameter pipe, or low line pressure. Consult
with plumber or gas supplier.
B. No LP in tank.
♦ Check LP (propane) tank. Refill if necessary.
PILOT WILL NOT STAY LIT AFTER CAREFULLY FOLLOWING LIGHTING INSTRUCTIONS.
A.
Check that pilot flame impinges on thermocouple. Clean and/or adjust pilot for maximum flame impingement.
B.
Ensure thermocouple connection at gas valve is fully inserted and tight (hand tight plus 1/4 turn).
C.
Thermocouple reading below 15 millivolts.
♦ Disconnect thermocouple from valve, place one millivolt meter lead wire on end of thermocouple and other millivolt meter lead
wire on thermocouple’s copper wire. Start pilot while holding valve knob in. If millivolt reading is less than 15 millivolts, replace
thermocouple.
D. Thermopile not generating sufficient millivolts.
♦ Pilot flame must be enveloping thermopile. Adjust pilot flame if necessary.
♦ Check thermopile wire connections at valve. Tighten if necessary.
♦ Check thermopile with millivolt meter. Turn remote / thermostat / wall switch or ON/OFF switch to OFF. Turn valve knob to
PILOT position (pilot should remain lit). Take reading at THTP & TP terminals on gas valve. Reading should be 350 millivolts
minimum. Replace thermopile if reading falls below specified minimum.
11
TROUBLESHOOTING
BURNER WILL NOT LIGHT
A.
Gas control knob not turned to ON.
B. ON/OFF switch not turned on.
C.
Remote, wall switch or thermostat not turned ON.
D.
Plugged main burner orifice.
E.
Remote, wall switch, thermostat or ON/ OFF switch wires defective.
♦ Check wires for proper connections. Place jumper wires across terminal at switch. If burner lights, replace defective switch.
♦ If switch checks ok, place jumper wires across switch wires on gas valve. If burner lights, wires are faulty or connections are bad.
FREQUENT PILOT OUTAGES
A.
Pilot shield not installed.
B. Pilot flame too high or too low, causing pilot safety to drop out.
♦ Clean and adjust flame for maximum flame impingement on thermopile.
BURNER WON’T STAY LIT
A.
Thermopile wires loose at valve terminals.
♦ Tighten if necessary.
B. Thermopile wires ground out due to pinched wires.
♦ Free pinched wires if necessary.
C
Refractory panel placement (if installed).
♦ Refractory panels must be tight against firebox walls. It may be necessary to secure panels with high-temp sealant, especially
around intake duct.
12
TROUBLESHOOTING
PILOT AND BURNER EXTINGUISH WHILE IN OPERATION
A.
No LP (propane) in tank.
♦ Check tank and refill if necessary.
B. Glass frame assembly not installed correctly.
♦ Refer to installation manual for proper glass frame assembly installment instructions.
C.
Defective thermopile or thermocouple.
♦ Check thermopile and thermocouple for proper millivolts.
D.
Improper pitch on horizontal vent.
♦ 1/4” (6mm) rise per foot is required on horizontal venting.
E.
Inner vent pipe leaking exhaust gases back into firebox.
♦ Check for leaks. Repair if necessary.
F.
Improper vent cap installation.
♦ Check for proper vent cap installation. Maximum downward slope of horizontal vent cap is 1/4” (6mm). Adjust if necessary.
♦ Check vent cap for blockage. Remove debris if necessary.
G. Excessive draft.
GLASS SOOTING
A.
Improper log placement.
♦ Refer to log placement instructions in fireplace installation manual.
B. Improper venturi setting.
♦ Venturi may need to be opened slightly to allow more air into gas mix.
C. Improper pitch on horizontal venting.
♦ 1/4” (6mm) rise per foot is required on horizontal venting.
FLAME BURNS BLUE AND LIFTS OFF BURNER
A.
Improper Venturi setting.
♦ Venturi may need to be closed slightly.
B. Improper vent cap installation.
♦ Check for proper vent cap installation.
C. Blockage or vent system leaks.
13
CONVERSION KIT INSTRUCTIONS
#OCK-S30B NAT GAS CONVERSION KIT / #OCK-S45 LP GAS CONVERSION KIT
This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturers instructions and all applicable codes and requirements of
the authority having jurisdiction. If the information in these instructions is not
followed exactly, a fire, explosion or productions of carbon monoxide may result,
causing property damage, personal injury or loss of life. The qualified service
WARNING
agency is responsible for proper installation of this kit. The installation is not proper
and complete until operation of the converted appliance is checked as specified in
the manufacturer’s instructions supplied with the kit. Refer to appliance owner’s
manual or product data plate for proper inlet and manifold pressure adjustments
and orifice sizing.
Kit includes: (1) Burner Orifice: NAT #30 / LP #45
(1) Valve and Pilot Assembly Conversion Instructions
CAUTION
WARNING
IMPORTANT
(1) Pilot Injector: NAT #51 / LP #35
(1) Gas Conversion Label
(1) Gas Label
THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING WITH
THE CONVERSION.
SHUT OFF GAS SUPPLY AND ELECTRIC POWER TO FIREPLACE.
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRIC POWER.
For high altitude installations: Above 2000ft. (610m) US / 4500ft. (1372m) Canada, consult the local gas distributor or
authority having jurisdiction for proper de-rating methods.
PREPARE FIREPLACE:
1.
2.
Turn fireplace off by pushing in and turning gas control knob clockwise to OFF
position.
Remove upper hood, upper louver and glass assembly.
3.
4.
5.
Remove logs and ember refractory from fireplace.
Remove pilot shield.
Remove burner / burner heat shield from fireplace.
PILOT ASSEMBLY
BURNER ORIFICE
REPLACE BURNER ORIFICE:
Remove existing orifice cap. Install orifice cap included with kit, making sure to
tighten cap securely. (Number stamped on orifice).
Nat: 30 / LP: 45
Figure 14b
Figure 14a
Your pilot assembly may look slightly different than one shown.
CONVERT PILOT ASSEMBLY:
1.
2.
3.
4.
Remove pilot hood by pulling it directly up from pilot bracket.
Insert 5/32” (4mm) hex key into hexagon key-way of injector, turn counter clockwise to remove from injector journal.
Place hex key into end of LP injector, install into injector journal, turning clockwise until a recommended torque of 9 lb. -in.
(1.0 Nm) is achieved. (LP injectors have groove around top, Nat injectors do not. Numbers are stamped on pilot injectors).
NAT: #51 / LP: #35
Align tab on base of pilot hood with slot in side of pilot journal. Push hood down, directly into pilot bracket. Hood must sit squarely
for proper operation.
14
CONVERSION KIT INSTRUCTIONS
CONVERT GAS VALVE:
Follow instructions included with kit to convert gas valve to either Nat. or LP.
COMPLETE THE CONVERSION:
1.
Re-install burner /burner heat shield assembly into fireplace, checking to ensure
burner venturi is properly seated over burner orifice.
2.
Burner venturi adjustment handle is attached to underside of control board. Access
through lower grill opening. Loosen wing nuts, adjust as necessary, pulling handle
forward to open, pushing backwards to close. Tighten wing nuts.
NAT: 1/8” (3mm) open - handle pushed back
LP: 5/8” (16mm) open - handle pulled forward
Note: Venturi may need further adjustment, depending on your venting configuration.
3.
Re-install pilot shield.
4.
Re-install ember refractory and logs*.
5.
Turn on gas and electrical supplies.
6.
Check for leaks at all connections with soapy water, whether field or factory made.
7.
Test inlet pressure*. Visually check pilot flame. Flame should envelope top of flame
sensor and extend onto burner far enough for proper ignition.
To Adjust pilot: Turn pilot adjustment screw clockwise to decrease or counterclockwise to increase pilot flame.
8.
Turn fireplace off.
9.
Affix gas type sticker to label.
PROPER BURNER / PILOT ORIENTATION
(Your pilot may look slightly different than one shown)
Figure 15a
GAS CONVERSION LABEL
(included with conversion kit)
Figure 15b
10. Re-install glass frame assembly, upper louver and upper hood.
11. Verify proper ignition and operation of fireplace.
12. Complete and affix ‘Gas Conversion’ label behind lower grill as close to gas valve as
possible.
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) (recommended)
11” WC (2.74 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.8” WC (.95 kPa)
10” WC (2.49 kPa)
MANIFOLD PRESSURE (LO)
1.1” WC (.27 kPa)
6.3” WC (1.57 kPa)
15
CONVERSION KIT INSTRUCTIONS
FLAME APPEARANCE:
Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi setting has
been factory set, adjustments may be necessary for optimal performance and visual aesthetics.
When fireplace is first lit, the flames will be blue. Flames will gradually turn yellowish-orange during first 15 minutes of operation. If
flames remain blue, or become dark orange with evidence of sooting (black tips), the burner tube venturi may need adjustment.
Short blue flames
venturi open too far
Lazy yellow flames - ideal
Correct pilot flame
Dark orange flames / black tips
Venturi closed too far
Excessive burner media
Figure 16b
Figure 16a
WARNING
Lifting (ghosting) flames
Improper Venting
Gas pressure too high
Burner tube adjustable venturi positioning should only be performed by a qualified professional service technician.
FACTORY SET BURNER TUBE VENTURI SETTINGS
(ADJUST AS NECESSARY FOR YOUR INSTALLATION)
NATURAL GAS
LP (PROPANE) GAS
1/8” (3mm) open
5/8” (16mm) open
BURNER TUBE VENTURI ADJUSTMENT GUIDELINES
VENTURI POSITION
FLAME COLOR
VENTURI ADJUSTMENT
Closed too far
Dark orange flame with black tips
Open venturi setting slightly
Open too far
Blue flames
Close venturi setting slightly
NOTE
IMPORTANT
If soot is present, check log positioning before adjusting burner venturi. Logs must not block burner ports.
SL I GHT AD J U STM EN T S T O BU R N ER VE N TU RI OP EN IN G CR E A TE D R AM A TI C R E SU LT S. A D J U ST AT SL I G HT
INCREM ENT S UNTIL DESI RED LOOK IS ACHI EVED. AL WAY S BURN FIREPLAC E FOR AT LEAST 15 M INUTES
AND ALLOW TIME TO COOL BEFORE MAKING ANY FURTHER ADJUSTMENTS.
TO ADJUST VENTURI:
WARNING
To avoid property damage or personal injury, allow fireplace time to cool before making any adjustments.
Burner venturi adjustment handle is attached to underside of control board. Access through lower grill opening. Loosen wing nuts, adjust
as necessary, pulling handle forward to open, pushing backwards to close. Tighten wing nuts.
Figure 16c
16
MAINTENANCE
The appliance is required to be inspected at least once a year by a professional service person.
The compartment below firebox must be cleaned at least once a year, more frequent cleaning may be required due to excessive lint from carpeting,
bedding materials, or other fibrous materials. Use a vacuum to clean all components at least once a year.
NOTE
INSTALLATION AND REPAIR SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE
INSPECTED BEFORE USE AND ANNUALLY BY A QUALIFIED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE
REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIALS, ETC. IT IS IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS AND CIRCULATION AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN .
CONTROL BOARD SYSTEM
Annual cleaning of burner system is required. Vacuum all components thoroughly.
The burner assembly may be removed for easier access. Refer to fireplace installation manual for complete instruction on removing &
reinstalling burner assembly.
Visually check for blocked port holes, especially near the pilot. Blocked port holes may cause delayed ignition.
Reinstall burner assembly following instructions in fireplace installation manual.
Visually check pilot light and burner when in operation. Flames should be steady, not lifting or floating.
Figure 17a
TMT-3875 Pilot
TMT-3875-MV Pilot
TMT-3875-IPI Pilot
Burner Orifice
Burner Ports
FAN
The fan should be disconnected from electrical current, and cleaned (vacuumed) every six months. The bearings are sealed and require no oiling.
VENT SYSTEM
Annual examination of venting system by a qualified agency is required.
IF VENT-AIR INTAKE SYSTEM IS DISASSEMBLED FOR ANY REASON, RE-INSTALL PER INSTRUCTIONS PROVIDED WITH INITIAL
INSTALLATION.
The flow of combustion and ventilation air must not be obstructed.
GLASS CLEANING & REPLACEMENT
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH GLASS/FRAME ASSEMBLY REMOVED, CRACKED OR BROKEN. REPLACEMENT OF THE
GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR QUALIFIED SERVICE PERSON.
Use protective gloves to handle any broken or damaged glass assembly components.
The glass assembly, part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
Replacement of glass & frame assembly, part #TMT-057T, must only be performed by a licensed or qualified service person.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass door assembly.
IMPORTANT
CAUTION
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
KEEP APPLIANCE AREA CLEAR OF COMBUSTIBLE MATERIALS, SUCH AS GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.
17
REPLACEMENT PARTS LIST
Replacement parts are available through your local dealer. Contact them for availability and pricing.
TMT-3875 MILLIVOLT CONTROL BOARD AND PARTS
TMT-770
TMT-771
Millivolt Board - Nat Gas
Millivolt Board - LP Gas
700-095
700-098
#30 Pilot Orifice - LP Gas
Pilot Hood
700-023
On/Off Rocker Switch
700-203
Manual Shut-off Valve
700-086N
S.I.T. Valve - Natural Gas
700-213B
18” Flexible Gas Line-Black
700-087
S.I.T. Valve - LP Gas
700-226
Flexible Gas Line-Valve to Burner Connection
700-088
Pilot / Generator / Thermocouple - Nat Gas
700-230
Natural Gas Orifice #30
700-089
Pilot / Generator / Thermocouple - LP Gas
700-245
LP Gas Orifice #45
700-090
Piezo Igniter w/ Nut (no wire)
OCK-S30B
Natural Gas Conversion Kit
700-091
700-092
700-093
700-094
Flexible Pilot Tubing (Valve to Pilot)
Millivolt Generator
Thermocouple
#51 Pilot Orifice - Natural Gas
OCK-S45
TMT-135
TMT-043
LP Gas Conversion Kit
Burner Assembly
Pilot Shield
TRF-200
TRF-201
Upper Hood
Lower Grill
TRF-200L
Upper Hood Louver
TMT-500
Log Set
TMT-1
#1 Log
TMT-2
#2 Log
TMT-3
#3 Log
TMT-4
#4 Log
TMT-5
#5 Log
TMT-6
#6 Log
TMT-7
#7 Log
900-KLK
Klinkers
900-REMB
Rock Wool Embers
TMT-005
Replacement Valance
900-006
1-1/8” Glass Gasket w/ Adhesive
TMT-057T
Valance with 26” x 35” glass
GRILL REPLACEMENT
LOG SET
GLASS & GLASS GASKET
Hussong Manufacturing Co., Inc.
P.O. Box 577
204 Industrial Park Drive
Lakefield, MN 56150-0577
USA
TMT-3875
www.kozyheat.com
18
Supplemental Installation and Homeowner
Information Manual for Trimont Model:
DIRECT VENT GAS FIREPLACE
English and French Installation Manuals Available Through Your Local Dealer or Visit Our Website at www.kozyheat.com
Les manuels d’installation en anglais et en français sont disponibles chez votre détaillant local ou en visitant notre site Web : www.kozyheat.com
IMPORTANT:
This supplemental installation and homeowner manual is to be used in
conjunction with TRIMONT INSTALLATION MANUAL. Read both manuals before installing and
operating appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING: Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to fireplace installation manual and this
manual. For assistance or additional information consult a qualified installer, service
agency or the gas supplier.
WARNING: If the information in these instructions is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.
—Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
◙ Do not try to light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
◙ If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
Report No. 216-F-13b-6.5
APRIL 2013
TMT-3875-IPI-SUP-REV-02
www.kozyheat.com
TABLE OF CONTENTS
SAFETY INFORMATION
Safety Information
2
SPECIFICATIONS
Components List
3
Gas Pressure Requirements / BTU’s
3
WIRING SCHEMATICS
Wiring Schematics
4
OPERATING INSTRUCTIONS
Control System Components
System Operations
Lighting and Shutdown
Pressure Testing
5
6-9
10-11
12
TROUBLESHOOTING
Troubleshooting
13-14
CONVERSION KIT INSTRUCTIONS
Conversion Kit Instructions
15-17
MAINTENANCE
Maintenance
18
REPLACEMENT PARTS
Replacement Parts
19
1
SAFETY INFORMATION
This fireplace has been tested by OMNI-Test Laboratories, Portland, Oregon and complies with:
ANSI Z21.88-2009/CSA 2.33-2009, “Standard for Vented Gas Fireplace Heaters”
CAN/CGA 2.17-M91 (R2009), “Gas-Fired Appliances for Use at High Altitudes”
CAN/CSA P.4.1-09, “Testing Method for Measuring Annual Efficiency”
This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation Code, CSA B149.1
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, wth the National
Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
Installation and repair should be done only by a qualified service person. The appliance should be inspected by a
qualified service person before use. Annual inspection by a qualified service person is required to maintain warranty.
More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulation air passageways of the appliance be kept clean.
If this appliance is installed directly on carpeting, tile or other combustible material other than wood flooring, the
appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at
risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other flammable material should not be placed on or near the appliance.
Adequate accessibility clearances for servicing and proper operation must be maintained.
This appliance must not share or be connected to a chimney flue serving any other appliance.
Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor and liquids.
The flow of combustion and ventilation air must not be obstructed.
Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.
The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance.
Work should be done by a qualified service technician.
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH THE GLASS/FRAME ASSEMBLY REMOVED, CRACKED
OR BROKEN. REPLACEMENT OF THE GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR
QUALIFIED SERVICE PERSON .
The glass assembly, Part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass assembly.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance.
Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this appliance.
Keep burner and control compartment clean.
Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect this
appliance and to replace any part of the control system and any gas control which has been under water.
2
SPECIFICATIONS
TMT-3875-IPI COMPONENTS LIST
PART NUMBER
DESCRIPTION
TMT-150
IPI Control Board Assembly
700-203
Manual Gas Shut-off Valve
TMT-135
Burner Assembly
TMT-I900
Refractory Set
TMT-500
Log Package
TMT-057T
Glass Frame Assembly
900-085
4” Restrictor Plate
500-TRF
3 pc. Grill Assembly (2 sets)
TMT-028-IPI
IPI Fan Kit
700-408
Remote Control
TMT-3875-IPI
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) recommended)
12” WC (2.99 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.8” WC (.95 kPa)
11” WC (2.74 kPa)
MANIFOLD PRESSURE (LO)
1.1” WC (.27 kPa)
2.9” WC (.72 kPa)
ORIFICE SIZE
#30
#45
INPUT BTU/hr. (kW)
47,000 (13.77 kW)
46,000 (13.48 kW)
MINIMUM INPUT BTU/hr. (kW)
23,500 (6.89 kW)
23,000 (6.74 kW)
3
WIRING SCHEMATICS
THIS SYSTEM REQUIRES ELECTRICITY (120V) AND / OR BATTERIES TO OPERATE.
Variable Speed Fan
SW1 Button (red)
885 Proflame
Battery Pack
Figure 4a
4
Burner
Pilot
Pilot
Flame
Sensor
Igniter
Main ON /OFF
Switch
IFC Control Module
Appliance
Ground Star
Variable Lights
USING BATTERY BACK UP WILL OPERATE BURNER ONLY. FAN AND LIGHT COMPONENTS WILL NOT FUNCTION ON BATTERY
BACK-UP POWER.
Main
Line
IMPORTANT
CONTROL SYSTEM COMPONENTS
REMOTE CONTROL
Blue back lit LCD display
ON /OFF Key
Thermostat Key
UP / DOWN Arrow Key
Key Lock
Mode Key
Low Battery Alarm
Transmission
Thermostat OFF/ON/SMART
Room Temperature
CPI Mode
Set Point
Temperature/Level/State
Flame ON
Figure 5a
Fan
Lights (not available in all fireplace models)
GAS VALVE
Stepper motor
Main valve connection (green)
Outlet pressure tap
Pilot connection (orange)
Inlet pressure tap
Figure 5b
Pilot flame adjustment
PILOT ASSEMBLY
Igniter
Pilot
Flame Sensor
Figure 5c
5
SYSTEM OPERATION
INITIALIZING THE SYSTEM FOR THE FIRST TIME
1.
Set ON/OFF rocker switch to OFF position.
2.
Install 4 AA batteries (included in components packet) into battery backup holder.
3.
Connect IFC Control Module to AC power supply.
4.
Install 3 AAA batteries (included in components packet) into remote control
battery bay (located on base of remote control).
LEDs
NOTE: Performing the next step will initiate Pilot Start-up in Manual Mode:
Pilot igniter will spark repeatedly.
Pilot will ignite if gas is supplied to the fireplace.
Remove all packaging / combustible material from fireplace before proceeding.
SW1 Button
Figure 6a
IFC Control Module
5.
Press red SW1 button on IFC control module until module beeps three (3) times and/or an amber LED is illuminated indicating the IFC
control module is ready to synchronize with the remote control.
6.
Within ten (10) seconds push remote control ON/OFF button. The IFC control module will beep (4) times to indicate the remote
control’s command is accepted and set to the particular code of that remote control. Press remote control ON/OFF button again. The
pilot will shut down indicating the remote has taken over. The system is now initialized.
7.
Setting ON/OFF rocker switch to ON position will allow you to operate fireplace with remote control.
TEMPERATURE DISPLAY
With the system in OFF position, press Thermostat Key and Mode Key at the same
time to change from degrees F to C. Look at remote control LCD screen to verify that
C or F is visible on right side of Room Temperature display.
Figure 6b
TURN ON THE APPLIANCE
Press ON/OFF key on remote control. The display will show all active icons on the screen. A single ‘beep’ from IFC Control Module will
Confirm reception of the command.
TURN OFF THE APPLIANCE
Press ON/OFF key on remote control. The display will show only room temperature and icon on the screen. A single ‘beep’ from IFC
control module will confirm reception of the command.
MANUALLY CONTROL FLAME WITH REMOTE CONTROL
The remote control has six (6) flame levels. With system ON and flame level at maximum, press Down Arrow Key once to reduce flame
height by one step until flame is turned off. The Up Arrow Key will increase flame height on step each time it is pressed. If Up Arrow Key
is pressed while system is on but flame is off, the flame will come on in High position. A single ‘beep’ will confirm reception of the
command. When SMART Thermostat is activated, manual flame height adjustment is disabled.
Figure 6c
6
SYSTEM OPERATION
ROOM THERMOSTAT (Remote Control Operation)
The remote control can operate as a room thermostat. The thermostat can be set to desired
temperature to control a rooms comfort level.
To activate this function, press the Thermostat Key. The LCD display will change to show
the room thermostat is ON and set temperature is now displayed. To adjust set
temperature, press Up or Down arrow keys until desired set temperature is display on
LCD screen.
Figure 7a
SMART THERMOSTAT (Remote Control Operation)
The Smart Thermostat function adjusts flame height based on set temperature and actual
room temperature. As room temperature gets closer to set point the Smart Function will
automatically adjust flame down.
1.
2.
Press Thermostat key until word SMART appears on right side of temperature bulb
graphic.
To adjust set temperature, press Up/Down arrow keys until desired set temperature is
displayed on LCD screen.
Figure 7b
When SMART Thermostat is activated, manual flame height adjustment is disabled.
FAN SPEED CONTROL
Fan speed can be adjusted through six (6) speeds. To activate this function use Mode Key
to index to fan control icon. Use Up/Down Arrow Keys to turn on, off or adjust fan speed.
A single ‘beep’ will confirm reception of the command.
In Thermostat Mode: Fan(s) have a five (5) minute delay time when fireplace is lit,
allowing time for heat to build in fireplace before operating, and will continue operating
for approximately twelve (12) minutes after fireplace has been turned off.
In Manual Mode: Fan (s) will operate at previous setting. There is no delay in start up or
stop time.
Figure 7c
ACCENT LIGHT KIT (not available in all fireplace models)
1.
Use MODE key to guide you to LIGHT icon.
2.
The light intensity can be adjusted through six (6) levels. Use UP/DOWN Arrow
Keys to adjust intensity level. A single beep will confirm reception of the command.
Figure 7d
KEY LOCK
This function locks the keys to avoid unsupervised operation.
To Activate: Press MODE and UP keys at same time.
To De-activate: Press MODE and UP keys at same time.
Figure 7e
7
SYSTEM OPERATION
LOW BATTERY DETECTION
REMOTE CONTROL: Remote control battery lifespan depends on various factors
including battery quality, number of ignitions, changes to room thermostat set point, etc.
When remote control batteries are low, a Battery Icon will appear on the LCD
display before all battery power is lost. When batteries are replaced this icon will
disappear.
BACKUP BATTERY PACK (used when electrical power is interrupted): Backup
batteries lifespan depends on various factors including battery quality, number of
ignitions, changes to room thermostat set point, etc. When backup batteries are low, a
double-beep will be emitted from the IFC control module when it receives an ON/OFF
command from the remote control. This is an alert for a low battery condition of the
backup batteries and after this double-beep warning, no commands will be accepted until
batteries are replaced. When batteries are replaced a beep will be emitted from IFC control
module as soon as powered.
Figure 8a
CONTINUOUS PILOT / INTERMITTENT PILOT (CPI/IPI)
This system has the option of a continuous (standing) pilot feature. This allows you to
change from a spark-to-pilot system to a standing pilot system during cold weather
conditions. By having the pilot on continuously, the firebox will remain warm and a draft
is established in the vent, allowing the main burner to turn on with less air -flow
disruption.
With system in OFF position, press Mode Key to index to CPI mode icon. Pressing the
UP Arrow Key will activate the Continuous Pilot Ignition Mode (CPI). Pressing the Down
Arrow Key will return to IPI. A single beep will confirm the reception of the command.
Figure 8b
A snowflake icon will be visible during setup of either IPI or CPI modes.
In IPI mode the snowflake is not visible on LCD screen.
In CPI mode the snowflake will remain visible on LCD screen.
RESETTING SYSTEM FOR MANUAL OPERATION
1.
Put ON/OFF switch in OFF position.
2.
Press red SW1 button on IFC control module until the IFC control module emits three
(3) beeps and an amber LED is illuminated, indicating the IFC control module is
ready to synchronize with remote control. Within ten (10) seconds press the red SW1
button on IFC control module again. The pilot will automatically light.
3.
Turn main burner on by pressing ON/OFF switch to ON position, turn off by pressing
ON/OFF switch to OFF position. Pilot will remain lit even if burner is turned off.
LEDs
SW1 Button
Figure 8c
IFC Control Module
When operating fireplace in this capacity, the only function available is burner operation on HI.
AUTOMATIC SAFETY RESTART
This system will execute an automatic turn OFF command within (24) hours of a continued pilot flame ignition. This allows the system to
verify correct safety functions. After turn OFF sequence is completed, the IFC control module will re-execute the latest command.
8
SYSTEM OPERATION
S .I .T. PRO FL A ME 2 I FC I G NI T I O N AND RE S E T I NFO RMAT I O N
IGNITION SEQUENCE
Starting from OFF, press remote control ON button. Approximately (4) seconds after ON/OFF button is pushed, the IFC control module
will start the spark. First ignition try will last approximately (60) seconds.
If there is no flame ignition (rectification) during the first try for ignition, the IFC control module will stop sparking for approximately (35)
seconds. After this wait time, the IFC control module will start the second try for ignition by sparking for approximately (60) seconds.
If ignition is successful on third ignition attempt, there will be a (60) second delay before the main burner lights.
If after this third attempt there is still no positive ignition, the IFC control module will go into LOCK OUT and the red LED will blink (3)
times in intervals until the system is reset.
LED Indicator Location: Corner of IFC control module. (IFC control module location determined by fireplace model and design. May
be located in component housing behind lower grill, or behind left side access panel).
LOCK OUT = LED blinks (3) times in intervals until the system is reset.
In Summary:
1. The IFC control module will try (2) times for ignition.
2. Each try for ignition will last approximately (60) seconds.
3. The wait time between the two tries is approximately (35) seconds.
RESET IFC CONTROL MODULE WHEN SYSTEM GOES INTO LOCK OUT
Reset Using ON/OFF Switch:
Set ON/OFF switch to OFF position. Wait approximately (2) seconds and move switch to the ON position. The ignition sequence will start
again.
Reset Using Remote Control ON/OFF Button:
Turn the system off by pressing the remote control ON/OFF button. After approximately (2) seconds press the remote control ON/OFF
button again. The IFC control module will reset and the ignition sequence will start again.
Reset By Cycling Flame:
In the Manual Flame Control Mode, use the Down Arrow Button to reduce flame to off (indicated by OFF displayed on Remote Control
Display Screen). Wait approximately (2) seconds and press the Up Arrow Button, the ignition sequence will start.
A D D I T I O N A L D I A G N O S T I C I N D I C AT I O N S I N F O R M AT I O N
Low Battery Condition (<4V) Remote Control: Battery Icon will appear on LCD remote control display. Replace batteries.
Low Battery Condition (<4V) Battery Backup: Red LED Indicator will blink (1) time in intervals. Low double-beep emitted from IFC
control module when it receives an ON/OFF command from the remote control. Replace Batteries.
Pilot Flame Error Condition: Red LED Indicator will blink (2) times in intervals. Contact your dealer if this occurs.
System Lock Out Condition: Red LED Indicator will blink (3) times in intervals. Make sure gas is turned on. Make sure sensor is not
shorted. Follow Reset IFC Control Module When System Goes Into Lock Out instructions above.
Remote Control
ON/OFF Button
LEDs
Up & Down
Arrow Buttons
IFC Control Module
Figure 9a
9
LIGHTING AND SHUTDOWN
FOR YOUR SAFETY - READ BEFORE OPERATING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT,
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
1. This appliance is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot by hand.
2. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use any phone in your building.
* Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
* If you cannot reach your gas supplier, call the fire department.
3. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system and any gas control which has been under water.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES AND
SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.
WARNING
CLOTHING OR OTHER FLAMMABLE MATERIAL MUST NOT BE PLACED ON OR NEAR THE APPLIANCE.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.
A PAINT SMELL WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING. IT IS RECOMMENDED TO LEAVE
THE FAN OFF DURING THIS PERIOD TO HELP SPEED THE PAINT CURING PROCESS.
NOTE
THIS FIREPLACE MAY PRODUCE NOISES OF VARYING DEGREE AS IT HEATS AND COOLS DUE TO METAL
EXPANSION AND CONTRACTION. THIS IS NORMAL AND DOES NOT AFFECT THE PERFORMANCE OR
LONGEVITY OF THE FIREPLACE.
DUE TO HIGH SURFACE TEMPERATURES, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
10
LIGHTING AND SHUTDOWN (cont.)
OPERATING INSTRUCTIONS
STOP!
1.
Read safety information on previous page and front
cover of this manual before conti nui ng.
1
2
Turn off all electric power to the appliance.
ATTENTION
This appliance is equipped with an ignition device
which automatically lights the pilot. DO NOT try to light
the pilot by hand.
2.
Press hand held remote OFF button.
3.
Wait five (5) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow ‘WHAT
TO DO IF YOU SMELL GAS’ below. If you don’t smell gas, go to
next step.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch; do not use any phone in your
building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Power OFF
OFF
3
5 MINUTES
5
4
Power ON
4.
Turn ON all electric power to the appliance.
5.
Press hand held remote ON button.
ON
Figure 11a
CAUTION
If fireplace will not operate, follow instructions
T O T U RN G A S O F F T O AP P L I AN CE a n d c a l l
your service technician or the gas supplier.
NOTE
When fireplace is initially lit, condensation will appear on
the glass; this is normal in all gas fireplaces and will
disappear after several minutes.
TO TURN GAS OFF TO APPLIANCE
1.
Press hand held remote OFF button.
2.
Turn OFF all electric power to appliance if service is to be performed.
3.
Manual shut-off valve located behind lower grill. Turn manual shut-off
valve to OFF.
1
Power OFF
OFF
3
Figure 11b
11
2
PRESSURE TESTING
IMPORTANT
Pressure check taps for manifold (outgoing) and inlet (incoming) pressure have been incorporated into the valve. The pressure
tap marked OUT measures outgoing pressure and the pressure tap marked IN measures incoming pressure. Follow instructions
below for proper testing procedures. Refer to page 16 for proper NAT and LP manifold pressures.
NOTE
The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The appliance must be isolated from the gas supply piping
system by closing its equipment shutoff valve during any pressure testing of the gas supply piping system at test pressures equal
to or less that 1/2 psi (3.5 kPa).
INLET PRESSURE TEST:
1.
Loosen inlet (IN) pressure tap screw (counter-clockwise).
2.
Attach manometer using a 5/16” I.D. hose.
3.
Set IPI/CPI switch to CPI setting.
4.
Light pilot. Note manometer reading.
5.
Move receiver slider switch to ON. Burner should light. Check pressure to ensure it stays between the min. and max. recommended
pressure settings.
6.
Set IPI/CPI switch to IPI setting . Move receiver slider switch to OFF. Pilot and burner should go out.
7.
Disconnect hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
8.
Relight pilot. Reattach manometer to inlet pressure tap to verify that it is completely sealed. Manometer should read no pressure.
NOTE
CAUTION
If inlet pressure reading is too high or too low, contact the gas company. Only a qualified gas service technician should adjust
incoming gas pressure.
A LOW PRESSURE READING CAN CAUSE DELAYED IGNITION.
MANIFOLD PRESSURE TEST:
1.
Light pilot.
2.
Loosen manifold (OUT) pressure tap screw (counter-clockwise).
3.
Attach manometer to pressure tap using a 5/16” I.D. hose.
4.
Set IPI/CPI switch to CPI setting.
5.
Move receiver slider switch to ON. Burner should light. Note manometer reading.
6.
Set IPI/CPI switch to IPI setting. Move receiver slider switch to OFF.
7.
Disconnect manometer hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
8.
Attach manometer to manifold pressure tap to verify it is completely sealed. Manometer should read no pressure when receiver slider
switch is moved to ON.
Outlet (Manifold) Pressure Screw
Figure 12a
Inlet Pressure Screw
12
TROUBLESHOOTING
ATTENTION
TROUBLESHOOTING MUST BE PERFORMED BY A QUALIFIED TECHNICIAN.
Before proceeding with the steps in the following troubleshooting guide, verify the power supply (AC/DC adapter or Fan Control Module)
is present and receiver batteries and/or battery pack are fresh and installed with correct polarity.
Make sure all connections between wire harnesses and system components are proper and positive.
Make sure communication link between transmitter and receiver is established.
Verify inlet pressure meets the recommended inlet pressure. If necessary adjust line pressure regulator.
PILOT WILL NOT LIGHT / STAY LIT
Electrical power interrupted or disconnected. Restore electrical power to fireplace or use battery back-up. Ensure batteries are fully
charged if using battery back-up as power source.
Verify gas supply is turned on. Check remote shut-off valves from fireplace. Usually there is a valve near the main. There may be
more than (1) valve between the fireplace and the main.
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line, too narrow diameter pipe, or low line
pressure. Consult with plumber or gas supplier.
No LP in tank. Check LP (propane) tank. Refill if necessary.
Wiring disconnection. Use wiring schematic in this manual to determine that all wiring connections are secure and correct.
Pilot flame not making contact with flame rectification sensor on pilot assembly. This valve is equipped with a pilot flame adjustment
screw. Adjust as necessary.
Pilot adjustment screw not sealed. Seal pilot adjustment screw. Do not over tighten.
PILOT FLAME ALWAYS ON / WILL NOT EXTINGUISH
CPI/IPI switch set to CPI position (down). Set switch to IPI position (up).
MAIN FLAME WILL NOT LIGHT
Remote not working properly. Replace batteries.
Remote set to thermostat mode and there is no call for heat. Adjust heat setting.
Thermostat disconnected or set too high. Set thermostat to lower temperature setting.
Ensure pilot flame will ignite. If not, see pilot flame troubleshooting above.
Ensure pilot flame is properly located to ignite main flame.
Plugged main burner orifice.
Wiring disconnection / improper wiring. Check for faulty or incorrect wiring.
Verify gas supply is turned on.
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line, too narrow diameter pipe, or low line
pressure. Consult with plumber or gas supplier.
13
TROUBLESHOOTING
PILOT AND BURNER EXTINGUISH WHILE IN OPERATION
No LP in tank. Check and refill if necessary.
Glass frame assembly not installed correctly. Refer to corresponding instructions in this manual.
Improper vent cap installation. Adjust if necessary.
Vent cap blockage. Remove debris if necessary.
Improper pitch on horizontal vent. 1/4” (6mm) rise per foot is required on horizontal venting.
Inner vent pipe leaking exhaust gases back into firebox. Check for leaks and repair if necessary.
Excessive draft.
GLASS SOOTING
Improper log placement. Refer to corresponding pages in this installation manual.
Improper venturi setting. Venturi may need to be opened slightly to allow more air into the gas mix.
Improper pitch on horizontal venting. 1/4” (6mm) rise per foot required on horizontal venting.
FLAME BURNS BLUE AND LIFTS OFF BURNER
Improper venturi setting. Venturi may need to be closed slightly.
Improper vent cap installation. Check for proper vent cap installation.
Blockage or vent system leaks.
NO REACTION TO COMMAND
Backup battery pack batteries or remote control batteries low. Replace batteries.
No communication between remote control and IFC control module. Reprogram remote control to IFC control module. Follow
INITIALIZING THE SYSTEM FOR THE FIRST TIME as outlined in this manual.
A maximum number of failed ignitions or flame restorations have been reached. Reset IFC control module.
Reset Using ON/OFF Switch:
Set ON/OFF switch to OFF position. Wait approximately (2) seconds and move switch to the ON position. The ignition sequence will
start again.
Reset Using Remote Control ON/OFF Button:
Turn the system off by pressing the Remote Control ON/OFF button. After approximately (2) seconds press the Remote Control
ON/OFF button again. The IFC control module will reset and the ignition sequence will start again.
Reset By Cycling Flame:
In the Manual Flame Control Mode, use the Down Arrow Button to reduce flame to off (indicated by OFF displayed on Remote
Control Display Screen). Wait approximately (2) seconds and press the Up Arrow Button, the ignition sequence will start.
14
CONVERSION KIT INSTRUCTIONS
#NCK-TMT-S NAT GAS CONVERSION KIT / #LCK-TMT-S LP GAS CONVERSION KIT
This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturers instructions and all applicable codes and requirements of
the authority having jurisdiction. If the information in these instructions is not
followed exactly, a fire, explosion or productions of carbon monoxide may result,
causing property damage, personal injury or loss of life. The qualified service agency
WARNING
is responsible for proper installation of this kit. The installation is not proper and
complete until operation of the converted appliance is checked as specified in the
manufacturer’s instructions supplied with the kit. Refer to appliance owner’s
manual or product data plate for proper inlet and manifold pressure adjustments
and orifice sizing.
Kit includes: (1) Gas Conversion Label
(1) Burner Orifice NAT #30 / LP #45
CAUTION
WARNING
IMPORTANT
(1) Pilot Injector NAT #51 / LP #30
(1) Gas Label
(1) Step Motor Pressure Regulator (50% turndown)
THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING WITH
THE CONVERSION.
SHUT OFF GAS SUPPLY AND ELECTRIC POWER TO FIREPLACE.
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRIC POWER.
For high altitude installations: Above 2000ft. (610m) US / 4500ft. (1372m) Canada, consult the local gas distributor or
authority having jurisdiction for proper de-rating methods.
PREPARE FIREPLACE:
1.
Remove upper hood, upper louver and glass assembly.
2.
Remove logs from fireplace.
3.
Remove pilot shield.
4.
Remove burner / burner heat shield assembly from fireplace.
PILOT ASSEMBLY
BURNER ORIFICE
REPLACE BURNER ORIFICE:
Remove existing orifice cap and replace with orifice cap included with kit, making
sure to tighten cap securely. (Number stamped on orifice.).
NAT. GAS: #30 / LP GAS: #45
Figure 15a
Figure 17b
CONVERT PILOT ASSEMBLY:
1.
Remove pilot hood by pulling it directly up from pilot bracket.
2.
Insert 5/32” (4mm) hex key into hexagon key-way of injector, turn counter clockwise to remove from injector journal.
3.
Place hex key into end of injector included with kit, install into injector journal, turning clockwise to a recommended torque of 9 lb-in.
(1.0 Nm) is achieved. (LP injectors have groove around top, Nat injectors do not. Numbers are stamped on pilot injectors).
NAT: #51 / LP: #30
4.
Align tab on base of pilot hood with slot in side of pilot journal. Push hood down, directly into pilot bracket. Hood must sit squarely
for proper operation.
15
CONVERSION KIT INSTRUCTIONS
CONVERT THE GAS CONTROL VALVE:
Follow stepper motor pressure regulator instruction sheet included with conversion
kit to convert gas valve. (LP or NAT marked on stepper motor pressure
regulator).
COMPLETE THE CONVERSION:
1.
Re-install burner/heat shield assembly into fireplace, checking to ensure
burner venturi is properly seated over burner orifices.
2.
Burner venturi adjustment handle is attached to underside of control board.
Access through lower grill opening. Loosen wing nuts, adjust as necessary,
pulling handle forward to open, pushing backwards to close. Tighten wing
nuts.
NAT: 1/8” (3mm) open - handle pushed back
LP: 5/8” (16mm) open - handle pulled forward
Venturi may need further adjustment, depending on venting configuration.
3.
Re-install pilot shield.
4.
Re-install ember refractory and logs*.
5.
Turn on gas and electrical supplies.
6.
Check for leaks at all connections with soapy water, whether field or factory
made.
7.
Test inlet pressure*. Visually check pilot flame. Flame should envelope top of
flame sensor and extend onto burner far enough for proper ignition.
To Adjust pilot: Turn pilot adjustment screw clockwise to decrease or
counter-clockwise to increase pilot flame.
8.
Turn fireplace off.
9.
Affix gas type sticker to label.
PROPER BURNER / PILOT ASSEMBLY ORIENTATION
(shown without pilot shield for clarity purposes)
Figure 16a
GAS CONVERSION LABEL
(included with conversion kit)
Figure 16b
10. Re-install glass frame assembly, upper louver and upper hood.
11. Verify proper ignition and operation of fireplace.
12. Complete and affix ‘Gas Conversion’ label behind lower grill.
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) recommended)
12” WC (2.99 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.8” WC (.95 kPa)
11” WC (2.74 kPa)
MANIFOLD PRESSURE (LO)
1.1” WC (.27 kPa)
2.9” WC (.72 kPa)
16
CONVERSION KIT INSTRUCTIONS
FLAME APPEARANCE:
Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi setting has
been factory set, adjustments may be necessary for optimal performance and visual aesthetics.
When fireplace is first lit, the flames will be blue. Flames will gradually turn yellowish-orange during first 15 minutes of operation. If
flames remain blue, or become dark orange with evidence of sooting (black tips), the burner tube venturi may need adjustment.
Short blue flames
venturi open too far
Lazy yellow flames - ideal
Correct pilot flame
Dark orange flames / black tips
Venturi closed too far
Excessive burner media
Figure 17b
Figure 17a
WARNING
Lifting (ghosting) flames
Improper Venting
Gas pressure too high
Burner tube adjustable venturi positioning should only be performed by a qualified professional service technician.
FACTORY SET BURNER TUBE VENTURI SETTINGS
(ADJUST AS NECESSARY FOR YOUR INSTALLATION)
NATURAL GAS
LP (PROPANE) GAS
1/8” (3mm) open
5/8” (16mm) open
BURNER TUBE VENTURI ADJUSTMENT GUIDELINES
VENTURI POSITION
FLAME COLOR
VENTURI ADJUSTMENT
Closed too far
Dark orange flame with black tips
Open venturi setting slightly
Open too far
Blue flames
Close venturi setting slightly
NOTE
IMPORTANT
If soot is present, check log positioning before adjusting burner venturi.
Logs must not block burner ports.
SL I GHT AD J U STM EN T S T O BU R N ER VE N TU RI OP EN IN G CR E A TE D R AM A TI C R E SU LT S. A D J U ST AT SL I G HT
INCREM ENT S UNTIL DESI RED LOOK IS ACHI EVED. AL WAY S BURN FIREPLAC E FOR AT LEAST 15 M INUTES
AND ALLOW TIME TO COOL BEFORE MAKING ANY FURTHER ADJUSTMENTS.
TO ADJUST BACK (MAIN) BURNER VENTURI:
WARNING
To avoid property damage or personal injury, allow fireplace time to cool before making any adjustments.
Back (main) burner venturi adjustment handle is attached to underside of control board. Access through lower grill opening. Loosen wing
nuts, adjust as necessary, pulling handle forward to open, pushing backwards to close. Tighten wing nuts.
Figure 17c
17
MAINTENANCE
The appliance is required to be inspected at least once a year by a professional service person.
The compartment below firebox must be cleaned at least once a year, more frequent cleaning may be required due to excessive lint from carpeting,
bedding materials, or other fibrous materials. Use a vacuum to clean all components at least once a year.
NOTE
INSTALLATION AND REPAIR SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE
INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING
MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT
CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN .
CONTROL BOARD SYSTEM
Annual cleaning of burner system is required. Vacuum all components thoroughly.
The burner assembly may be removed for easier access. Refer to fireplace installation manual for complete instruction on removing &
reinstalling burner assembly.
Visually check for blocked port holes, especially near the pilot. Blocked port holes may cause delayed ignition.
Reinstall burner assembly following instructions in fireplace installation manual.
Visually check pilot light and burner when in operation. Flames should be steady, not lifting or floating.
TMT-3875-IPI Pilot
Burner Orifice
Burner Ports
Figure 18a
FAN
The fan should be disconnected from electrical current, and cleaned (vacuumed) every six months. The bearings are sealed and require no oiling.
VENT SYSTEM
Annual examination of venting system by a qualified agency is required.
IF VENT-AIR INTAKE SYSTEM IS DISASSEMBLED FOR ANY REASON, RE-INSTALL PER INSTRUCTIONS PROVIDED WITH INITIAL
INSTALLATION.
The flow of combustion and ventilation air must not be obstructed.
GLASS CLEANING & REPLACEMENT
Clean glass only when cool and only with non-abrasive cleansers.
CAUTION: Do not operate the appliance with glass removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or
qualified service person.
Use protective gloves to handle any broken or damaged glass assembly components.
The glass assembly, part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
Replacement of glass & frame assembly, part #TMT-057T, must only be performed by a licensed or qualified service person.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass door assembly.
IMPORTANT
CAUTION
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
KEEP APPLIANCE AREA CLEAR OF COMBUSTIBLE MATERIALS, SUCH AS GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.
18
REPLACEMENT PARTS LIST
Replacement parts are available through your local dealer. Contact them for availability and pricing.
CONTROL BOARD AND PARTS
TMT-150
Control Board - Nat Gas
700-504
Valve Step Motor - Natural Gas
TMT-151
Control Board - LP Gas
700-504-1
Valve Step Motor - LP Gas
700-567
SIT IPI Valve - Natural
700-203
Manual Shut-off Valve
700-567-1
SIT IPI Valve - LP
700-213B
18” Flexible Gas Line-Black
700-562
Proflame 2 IFC Board
700-226
Flexible Gas Line-Valve to Burner Connection
700-563
IFC Wire Harness Assembly
700-230
Natural Gas Orifice #30
700-551
Pilot Assembly - Natural Gas
700-245
LP Gas Orifice #45
700-551-1
Pilot Assembly - LP Gas
NCK-TMT-S
Natural Gas Conversion Kit
700-408
Transmitter
LCK-TMT-S
LP Gas Conversion Kit
700-094
#51 Natural Gas Pilot Orifice
TMT-135
Burner / Log Grate Assembly
700-168
#35 LP Gas Pilot Orifice
TMT-043
Pilot Shield
TRF-200
Upper Hood
TRF-201
Lower Grill
TRF-200L
Upper Hood Louver
TMT-500
Log Set
TMT-1
#1 Log
TMT-2
#2 Log
TMT-3
#3 Log
TMT-4
#4 Log
TMT-5
#5 Log
TMT-6
#6 Log
TMT-7
#7 Log
900-KLK
Klinkers
900-REMB
Rock Wool Embers
TMT-005
Replacement Valance
900-006
1-1/8” Glass Gasket w/ Adhesive
TMT-057T
Valance with 26” x 35” glass
TMT-028-IPI
Fan Assembly
GRILL REPLACEMENT
LOG SET
GLASS & GLASS GASKET
FAN ASSEMBLIES
REFRACTORY REPLACEMENT
TMT-I900LS
Left Side Refractory Panel
TMT-I900RS
Right Side Refractory Panel
TMT-I901
Bottom Refractory Panel
TMT-900E
Ember / Log Refractory
Hussong Manufacturing Co., Inc.
P.O. Box 577
204 Industrial Park Drive
Lakefield, MN 56150-0577
USA
TMT-3875-IPI
www.kozyheat.com
19
Supplemental Installation and Homeowner
Information Manual for Trimont Model:
DIRECT VENT GAS FIREPLACE
IMPORTANT:
This supplemental installation and homeowner manual is to be used in
conjunction with TRIMONT INSTALLATION MANUAL. Read both manuals before installing and
operating appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
English and French Installation Manuals
Available Through Your Local Dealer or
Visit Our Website at www.kozyheat.com
WARNING: Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to fireplace installation manual and this
manual. For assistance or additional information consult a qualified installer, service
agency or the gas supplier.
WARNING: If the information in these instructions is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.
—Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
◙ Do not try to light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbors phone. Follow the gas supplier
instructions
◙ If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
Report No. 216-F-13b-6.5
APRIL 2013
TMT-3875-MV-SUP-REV-02
www.kozyheat.com
TABLE OF CONTENTS
SAFETY INFORMATION
Safety Information
2
SPECIFICATIONS
Components List
3
Gas Pressure Requirements / BTU’s
3
WIRING SCHEMATICS
Wiring Schematics
4
OPERATING INSTRUCTIONS
Control System Components
5-6
System Operations
7-9
Lighting and Shutdown Instructions
Pressure Testing
10-12
13
TROUBLESHOOTING
Troubleshooting
14-15
CONVERSION KIT INSTRUCTIONS
Conversion Kit Instructions
16-18
MAINTENANCE
Maintenance
19
REPLACEMENT PARTS
Replacement Parts
20
1
SAFETY INFORMATION
This fireplace has been tested by OMNI-Test Laboratories, Portland, Oregon and complies with:
ANSI Z21.88-2009/CSA 2.33-2009, “Standard for Vented Gas Fireplace Heaters.”
CAN/CGA 2.17-M91 (R2009), “Gas-Fired for Use at High Altitudes.”
CAN/CSA P.4.1-09, “Testing Method for Measuring Annual Efficiency”.
This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation Code, CSA B149.1
Installation and repair should be done only by a qualified service person. The appliance should be inspected by a
qualified service person before use. Annual inspection by a qualified service person is required to maintain warranty.
More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulation air passageways of the appliance be kept clean.
If this appliance is installed directly on carpeting, tile or other combustible material other than wood flooring, the
appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at
risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other flammable material should not be placed on or near the appliance.
Adequate accessibility clearances for servicing and proper operation must be maintained.
This appliance must not share or be connected to a chimney flue serving any other appliance.
Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor and liquids.
The flow of combustion and ventilation air must not be obstructed.
Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.
The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance.
Work should be done by a qualified service technician.
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH THE GLASS/FRAME ASSEMBLY REMOVED, CRACKED
OR BROKEN. REPLACEMENT OF THE GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR
QUALIFIED SERVICE PERSON .
The glass assembly, Part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass assembly.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance.
Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this appliance.
Keep burner and control compartment clean.
Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect this
appliance and to replace any part of the control system and any gas control which has been under water.
2
SPECIFICATIONS
TMT-3875-MV COMPONENTS LIST
PART NUMBER
DESCRIPTION
TMT-700
Control Board Assembly
700-203
Manual Gas Shut-off Valve
TMT-135
Burner Assembly
TMT-I900
Refractory Set
TMT-500
Log Package
TMT-057T
Glass Frame Assembly (2)
900-085
4” Restrictor Plate
500-TRF
3 pc. Grill Assembly (2 sets)
TMT-028-IPI
IPI Fan Kit
700-308
Remote Control
TMT-3875-MV
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) (recommended)
11” WC (2.74 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.5” WC (.87 kPa)
10” WC (2.49 kPa)
MANIFOLD PRESSURE (LO)
1.6” WC (.40 kPa)
6.4” WC (1.59 kPa)
ORIFICE SIZE
#30
#45
INPUT BTU/hr. (kW)
47,000 (13.77 kW)
46,000 (13.48 kW)
MINIMUM INPUT BTU/hr. (kW)
31,500 (9.23 kW)
35,500 (10.4 kW)
3
WIRING SCHEMATICS
THIS SYSTEM REQUIRES ELECTRICITY (120V) AND / OR BATTERIES TO OPERATE.
IMPORTANT
USING BATTERY BACK UP WILL OPERATE BURNER ONLY. FAN AND LIGHT COMPONENTS WILL NOT FUNCTION ON BATTERY
BACK-UP POWER.
Pilot Assembly
To Fan
To Lights
Millivolt Operator
(top view)
Not used
Gas Valve
Figure 4a
4
CONTROL SYSTEM COMPONENTS
REMOTE CONTROL
Figure 5a
GAS VALVE
Manifold Pressure Tab
Step Motor
Inlet Pressure Tab
Gas Control Knob
Valve Terminals
Figure 5b
PILOT ASSEMBLY
Thermopile
Pilot Hood
Electrode
Thermocouple
Figure 5c
5
CONTROL SYSTEM COMPONENTS
RECEIVER
Figure 6a
FAN CONTROL MODULE
Figure 6b
SYSTEM OPERATION
INITIALIZING THE SYSTEM FOR THE FIRST TIME
1.
Move slider switch on receiver to OFF position.
2.
Install 4 AA batteries (included in components packet) into receiver battery
bay.
3.
Move slider switch to REMOTE position.
4.
Using the end of a paper clip, or other similar object, press button through
hole marked PRG on receiver front cover. Receiver will ‘beep’ three (3)
times to indicate it is ready to synchronize with a transmitter.
5.
Install 3 AAA batteries (included in components packet) into transmitter
battery bay (located on base of transmitter). Push the ON button. The
receiver will beep four (4) times to indicate the transmitter’s command is
accepted and set to the particular code of that transmitter.
6.
Turn On fan control module, switching to ON ( | ) position.
7.
The system is now initialized.
NOTE
Figure 6c
This procedure must be performed every time batteries are replaced in Receiver or Transmitter.
6
SYSTEM OPERATION
TEMPERATURE DISPLAY
With the system in OFF position, press Thermostat Key and Mode Key at the
same time to change from degrees F to C. Look at transmitter LCD screen to
verify that C or F is visible on right side of Room Temperature display.
Figure 7a
REMOTE FLAME CONTROL
The remote control has six (6) flame levels. With system ON and flame level at maximum, press Down Arrow Key once to reduce flame
height by one step until flame is turned off. The Up Arrow Key will increase flame height on step each time it is pressed. If Up Arrow Key
is pressed while system is on but flame is off, the flame will come on in High position. A single ‘beep’ will confirm reception of the
command.
Figure 7b
ROOM THERMOSTAT (Transmitter Operation)
The remote control can operate as a room thermostat. The thermostat can be set to desired temperature to control a rooms comfort level.
To activate this function, press the Thermostat Key. The LCD display will change to show the room thermostat is ON and set temperature is
now displayed. To adjust set temperature, press Up or Down arrow keys until desired set temperature is display on LCD screen.
Figure 7c
7
SYSTEM OPERATION
SMART THERMOSTAT (Transmitter Operation)
The Smart Thermostat function adjusts flame height based on set temperature and actual room temperature. As room temperature gets closer
to set point the Smart Function will automatically adjust flame down.
1.
Press Thermostat key until the word SMART appears on right side of temperature bulb graphic.
2.
To adjust set temperature, press Up/Down arrow keys until desired set temperature is displayed on LCD screen.
Figure 8a
FAN SPEED CONTROL
Fan speed can be adjusted through six (6) speeds. To activate this function use Mode Key to index to fan control icon. Use Up/Down Arrow
Keys to turn on, off or adjust fan speed. A single ‘beep’ will confirm reception of the command.
Figure 8b
ACCENT LIGHT KIT (not available in all fireplace models)
The auxiliary function controls the AUX power outlet on the Fan control module which in turn controls the light kit.
1.
Use MODE key to guide you to AUX icon.
2.
Press Up Arrow Key to turn light kit on, press Down Arrow Key to turn light kit off. A single ‘beep’ will confirm reception of the
command.
3.
Use the installed dimmer switch to adjust brightness of lights.
Figure 8c
8
SYSTEM OPERATION
KEY LOCK
This function locks the keys to avoid unsupervised operation.
To Activate: Press MODE and UP keys at same time.
To De-activate: Press MODE and UP keys at same time.
Figure 9a
LOW BATTERY DETECTION
TRANSMITTER: Remote control battery lifespan depends on various factors including battery quality, number of ignitions, changes to
room thermostat set point, etc.
When transmitter batteries are low, a Battery Icon will appear on the LCD display before all battery power is lost. When batteries are
replaced this icon will disappear.
RECEIVER: Receiver battery lifespan depends on various factors including battery quality, number of ignitions, changes to room
thermostat set point, etc.
When receiver batteries are low, no ‘beep’ will be emitted from Receiver when it receives an ON/OFF command from the Transmitter. This
is an alert for a low battery condition for the Receiver. When the batteries are replaced the ‘beep’ will be emitted from the Receiver when
ON/OFF Key is pressed.
Figure 9b
MANUAL BYPASS OF REMOTE SYSTEM
If batteries of the Receiver or Transmitter are low or depleted, the appliance can be turned on by sliding the three position slider switch on
the Receiver to the ON position. This will bypass the remote control feature of the system and the appliance main burner will come on if
gas valve is in the ON position.
TURN ON THE APPLIANCE
Follow instructions as outlined in Lighting and Shutdown. Pages 11-12.
Press ON/OFF key on transmitter. The display will show all active icons on the screen. A single ‘beep’ from receiver will confirm
reception of the command.
TURN OFF THE APPLIANCE
Follow instructions as outlined in Lighting and Shutdown. Pages 11-12.
Press ON/OFF key on transmitter. The display will show only room temperature and icon on the screen. A single ‘beep’ from receiver will
confirm reception of the command.
9
LIGHTING AND SHUTDOWN
FOR YOUR SAFETY - READ BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
DUE TO HIGH SURFACE TEMPERATURES, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
A.
This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B.
BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in, or turn by hand, do not try to
repair it, call a qualified service technician. Forced or attempted repair may result in a fire or explosion, and loss of war ranty.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system which has been under water.
WARNING
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.
WARNING
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES AND
SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE. CLOTHING OR OTHER FLAMMABLE
MATERIAL MUST NOT BE PLACED ON OR NEAR THE APPLIANCE.
A PAINT SMELL WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING. IT IS RECOMMENDED TO LEAVE
THE FAN OFF DURING THIS PERIOD TO HEL P SPEED THE PAINT CURING PROCESS.
NOTE
THIS FIREPLACE MAY PRODUCE NOISES OF VARYING DEGREES AS IT HEATS AND COOLS DUE TO METAL
EXPANSION AND CONTRACTION. THIS IS NORMAL AND DOES NOT AFFECT THE PERFORMANCE OR
LONGEVITY OF THE FIREPLACE.
10
LIGHTING AND SHUTDOWN (cont.)
LIGHTING INSTRUCTIONS
1.
Turn off all electrical power to appliance.
2.
Open lower grill to access gas valve & controls.
3.
Push gas control knob in slightly and turn clockwise to OFF.
4.
Wait five (5) minutes to clear out any gas. Then smell gas,
including near the floor. If you then smell gas, STOP!
Follow WHAT TO DO IF YOU SMELL GAS safety
information below. If you don’t smell gas, go to next step.
5 MINUTES
PILOT
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch; do not use the phone in your
building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
NOTE
Gas control knob cannot be turned from PILOT
to OFF unless knob is pushed in slightly.
Do not force.
5.
Locate pilot - follow metal tube from gas control. (Located
inside combustion chamber).
6.
Push gas control knob on gas valve in slightly and turn
counterclockwise to PILOT.
7.
Push valve knob in and hold while repeatedly pressing piezo
igniter button until pilot is lit while continuing to hold in gas
control knob.
8.
Hold gas control knob in for one (1) minute after pilot is lit.
Release gas control knob. If pilot goes out, repeat steps 3-8.
When pilot is lit, proceed to step 9.
CAUTION
9.
PILOT
TUBE
1 MINUTE
If knob does not pop up when released, stop and
immediately call your service technician or the
gas supplier. If pilot will not stay lit after
several tries, turn gas control knob to OFF
and call your service technician or gas supplier.
Turn on all electric power to appliance.
10. Push gas control knob in slightly and turn counterclockwise
to ON.
11. Move receiver switch to REMOTE position.
12. Press hand held remote ON button.
NOTE
When fireplace is initially lit, condensation will
appear on the glass; this is normal in all gas
fireplaces and will disappear after several
minutes.
Figure 11a
11
LIGHTING AND SHUTDOWN (cont.)
TO TURN OFF GAS TO APPLIANCE
TURN BURNER OFF
To turn burner OFF, press hand held remote OFF button.
NOTE
The pilot will stay lit.
TURN PILOT OFF
Figure 12a
Turn pilot off by pushing in and turning gas control knob to OFF.
DO NOT FORCE.
NOTE
This control valve has an interlock device. If pilot has been
turned off, it cannot be relit until thermocouple has cooled,
(approximately 60 seconds).
12
PRESSURE TESTING
IMPORTANT
Pressure check taps for manifold (outgoing) and inlet (incoming) pressure have been incorporated into the valve. The pressure
tap marked OUT measures outgoing pressure and the pressure tap marked IN measures incoming pressure. Follow instructions
below for proper testing procedures. Refer to page 17 for proper NAT and LP manifold pressures.
NOTE
The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The appliance must be isolated from the gas supply piping
system by closing its equipment shutoff valve during any pressure testing of the gas supply piping system at test pressures equal
to or less that 1/2 psi (3.5 kPa).
INLET PRESSURE TEST:
1.
Loosen inlet (IN) pressure tap screw (counter-clockwise).
2.
Attach manometer using a 5/16” I.D. hose.
3.
Light pilot.
4.
Turn gas control knob to ON (burner should not light). Note manometer reading.
5.
Press hand held remote ON button. Check pressure to ensure it stays near maximum inlet pressure.
6.
Press hand held remote OFF button.
7.
Turn gas control knob to OFF.
8.
Disconnect hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
9.
Relight pilot and turn gas control knob to ON. Reattach manometer to inlet pressure tap to verify it is completely sealed.
Manometer should read no pressure.
NOTE
If inlet pressure reading is too high or too low, contact the gas company. Only a qualified gas service technician should adjust
the incoming gas pressure.
MANIFOLD PRESSURE TEST:
1.
Light pilot.
2.
Loosen manifold (OUT) pressure tap screw (counter-clockwise).
3.
Attach manometer to pressure tap using a 5/16” I.D. hose.
4.
Turn gas control knob to ON.
5.
Press hand held remote ON button and note manometer reading.
6.
Press hand held remote OFF button.
7.
Disconnect manometer hose and tighten screw (clockwise). Screw should be snug, do not over tighten.
8.
Attach manometer to manifold pressure tap to verify it is completely sealed. Manometer should read no pressure when burner is turned
on.
CAUTION
A LOW PRESSURE READING CAN CAUSE DELAYED IGNITION.
MANIFOLD
INLET
Figure 13a
13
TROUBLESHOOTING
ATTENTION
TROUBLESHOOTING MUST BE PERFORMED BY A QUALIFIED TECHNICIAN.
Before proceeding with the steps in the following troubleshooting guide, verify the power supply (AC/DC adapter or Fan Control Module)
is present and receiver batteries and/or battery pack are fresh and installed with correct polarity.
Make sure all connections between wire harnesses and system components are proper and positive.
Make sure communication link between transmitter and receiver is established.
Verify inlet pressure meets the recommended inlet pressure. If necessary adjust line pressure regulator.
PILOT WILL NOT LIGHT / STAY LIT
Electrical power interrupted or disconnected. Restore electrical power to fireplace or use battery back-up. Ensure batteries are fully
charged if using battery back-up as power source.
Verify gas supply is turned on. Check remote shut-off valves from fireplace. Usually there is a valve near the main. There may be
more than (1) valve between the fireplace and the main.
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line, too narrow diameter pipe, or low line
pressure. Consult with plumber or gas supplier.
No LP in tank. Check LP (propane) tank. Refill if necessary.
Wiring disconnection. Use wiring schematic in this manual to determine that all wiring connections are secure and correct.
Pilot flame not making contact with flame rectification sensor on pilot assembly. This valve is equipped with a pilot flame adjustment
screw. Adjust as necessary.
Pilot adjustment screw not sealed. Seal pilot adjustment screw. Do not over tighten.
PILOT FLAME ALWAYS ON / WILL NOT EXTINGUISH
CPI/IPI switch set to CPI position (down). Set switch to IPI position (up).
MAIN FLAME WILL NOT LIGHT
Remote not working properly. Replace batteries.
Remote set to thermostat mode and there is no call for heat. Adjust heat setting.
Thermostat disconnected or set too high. Set thermostat to lower temperature setting.
Ensure pilot flame will ignite. If not, see pilot flame troubleshooting above.
Ensure pilot flame is properly located to ignite main flame.
Plugged main burner orifice.
Wiring disconnection / improper wiring. Check for faulty or incorrect wiring.
Verify gas supply is turned on.
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line, too narrow diameter pipe, or low line
pressure. Consult with plumber or gas supplier.
14
TROUBLESHOOTING
PILOT AND BURNER EXTINGUISH WHILE IN OPERATION
No LP in tank. Check and refill if necessary.
Glass frame assembly not installed correctly. Refer to corresponding instructions in this manual.
Improper vent cap installation. Adjust if necessary.
Vent cap blockage. Remove debris if necessary.
Improper pitch on horizontal vent. 1/4” (6mm) rise per foot is required on horizontal venting.
Inner vent pipe leaking exhaust gases back into firebox. Check for leaks and repair if necessary.
Excessive draft.
GLASS SOOTING
Improper log placement. Refer to corresponding pages in this installation manual.
Improper venturi setting. Venturi may need to be opened slightly to allow more air into the gas mix.
Improper pitch on horizontal venting. 1/4” (6mm) rise per foot required on horizontal venting.
FLAME BURNS BLUE AND LIFTS OFF BURNER
Improper venturi setting. Venturi may need to be closed slightly.
Improper vent cap installation. Check for proper vent cap installation.
Blockage or vent system leaks.
NO REACTION TO COMMAND
Receiver or transmitter batteries low. Replace batteries.
No communication between remote control and receiver. Reprogram transmitter to receiver. Follow INITIALIZING THE SYSTEM
FOR THE FIRST TIME as outlined in this manual.
15
CONVERSION KIT INSTRUCTIONS
#NCK-TMTMV-S NAT GAS CONVERSION KIT / #LCK-TMTMV-S LP GAS CONVERSION KIT
This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturers instructions and all applicable codes and requirements of
the authority having jurisdiction. If the information in these instructions is not
followed exactly, a fire, explosion or productions of carbon monoxide may result,
causing property damage, personal injury or loss of life. The qualified service agency
WARNING
is responsible for proper installation of this kit. The installation is not proper and
complete until operation of the converted appliance is checked as specified in the
manufacturer’s instructions supplied with the kit. Refer to appliance owner’s
manual or product data plate for proper inlet and manifold pressure adjustments
and orifice sizing.
Kit includes: (1) Gas Conversion Label
(1) Burner Orifice NAT #30 / LP #45
CAUTION
WARNING
IMPORTANT
(1) Pilot Injector NAT #62 / LP #35
(1) Step Motor Pressure Regulator
(1) Gas Label
THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING WITH
THE CONVERSION.
SHUT OFF GAS SUPPLY AND ELECTRIC POWER TO FIREPLACE.
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRIC POWER.
For high altitude installations: Above 2000ft. (610m) US / 4500ft. (1372m) Canada, consult the local gas distributor or
authority having jurisdiction for proper de-rating methods.
PREPARE FIREPLACE:
1.
Remove upper hood, upper louver and glass assembly.
2.
Remove logs from fireplace.
3.
Remove pilot shield.
4.
Remove burner / burner heat shield assembly from fireplace.
PILOT ASSEMBLY
BURNER ORIFICE
REPLACE BURNER ORIFICE:
Remove existing orifice cap and replace with orifice cap included with kit, making
sure to tighten cap securely. (Number stamped on orifice.).
NAT. GAS: #30 / LP GAS: #45
Figure 16a
Figure 16b
CONVERT PILOT ASSEMBLY:
1.
Remove pilot hood by pulling it directly up from pilot bracket.
2.
Insert 5/32” (4mm) hex key into hexagon key-way of injector, turn counter clockwise to remove from injector journal.
3.
Place hex key into end of injector included with kit, install into injector journal, turning clockwise to a recommended torque of 9 lb-in.
(1.0 Nm) is achieved. (LP injectors have groove around top, Nat injectors do not. Numbers are stamped on pilot injectors).
NAT: #62 / LP: #35
4.
Align tab on base of pilot hood with slot in side of pilot journal. Push hood down, directly into pilot bracket. Hood must sit squarely
for proper operation.
16
CONVERSION KIT INSTRUCTIONS
CONVERT THE GAS CONTROL VALVE:
Follow stepper motor pressure regulator instruction sheet included with conversion
kit to convert gas valve. (LP or NAT marked on stepper motor pressure
regulator).
COMPLETE THE CONVERSION:
1.
Re-install burner /burner heat shield assembly into fireplace, checking to
ensure burner venturi is properly seated over burner orifice.
2.
Remove set screw from venturi wheel located under board. Move handle to
correct position.
CORRECT SETTINGS: NAT. : 1/8” (3mm) open / (#9 position)
L.P. : 5/8” (16mm) open / (#1 position)
Secure with screw previously removed, keeping in mind Venturi may need
further adjustment, depending on your specific venting configuration.
PROPER BURNER / PILOT ASSEMBLY ORIENTATION
(shown without pilot shield for clarity purposes)
Figure 17a
Venturi opening
3.
Re-install pilot shield.
4.
Re-install ember refractory and logs.
5.
Turn on gas and electrical supplies.
6.
Check for leaks at all connections with soapy water, whether field or factory
made.
7.
Test inlet pressure. Visually check pilot flame. Flame should envelope top of
flame sensor and extend onto burner far enough for proper ignition.
Figure 17b
To Adjust pilot: Turn pilot adjustment screw clockwise to decrease or
counter-clockwise to increase pilot flame.
8.
Turn fireplace off.
9.
Affix gas type sticker to label.
10. Re-install glass frame assembly, upper louver and upper hood.
11. Verify proper ignition and operation of fireplace.
12. Complete and affix ‘Gas Conversion’ label behind lower grill.
GAS CONVERSION LABEL
(included with conversion kit)
Figure 17c
NATURAL GAS
LP GAS
MINIMUM INLET GAS PRESSURE
5” WC (1.25 kPa) (7” WC (1.74 kPa) recommended)
11” WC (2.74 kPa) (recommended)
MAXIMUM INLET GAS PRESSURE
10.5” WC (2.62 kPa)
13” WC (3.24 kPa)
MANIFOLD PRESSURE (HI)
3.5” WC (.87 kPa)
10” WC (2.49 kPa)
MANIFOLD PRESSURE (LO)
1.6” WC (.40 kPa)
6.4” WC (1.59 kPa)
17
CONVERSION KIT INSTRUCTIONS
FLAME APPEARANCE:
Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi setting has
been factory set, adjustments may be necessary for optimal performance and visual aesthetics.
When fireplace is first lit, the flames will be blue. Flames will gradually turn yellowish-orange during first 15 minutes of operation. If
flames remain blue, or become dark orange with evidence of sooting (black tips), the burner tube venturi may need adjustment.
Short blue flames
venturi open too far
Lazy yellow flames - ideal
Correct pilot flame
Dark orange flames / black tips
Venturi closed too far
Excessive burner media
Figure 18b
Figure 18a
WARNING
Lifting (ghosting) flames
Improper Venting
Gas pressure too high
Burner tube adjustable venturi positioning should only be performed by a qualified professional service technician.
FACTORY SET BURNER TUBE VENTURI SETTINGS
(ADJUST AS NECESSARY FOR YOUR INSTALLATION)
NATURAL GAS
LP (PROPANE) GAS
1/8” (3mm) open / #9 position
5/8” (16mm) open / #1 position
BURNER TUBE VENTURI ADJUSTMENT GUIDELINES
VENTURI POSITION
FLAME COLOR
VENTURI ADJUSTMENT
Closed too far
Dark orange flame with black tips
Open venturi setting slightly
Open too far
Blue flames
Close venturi setting slightly
NOTE
IMPORTANT
If soot is present, check log positioning before adjusting burner venturi. Logs must not block burner ports.
SL I GHT AD J U STM EN T S T O BU R N ER VE N TU RI OP EN IN G CR E A TE D R AM A TI C R E SU LT S. A D J U ST AT SL I G HT
INCREM ENT S UNTIL DESI RED LOOK IS ACHI EVED. AL WAY S BURN FIREPLAC E FOR AT LEAST 15 M INUTES
AND ALLOW TIME TO COOL BEFORE MAKING ANY FURTHER ADJUSTMENTS.
TO ADJUST VENTURI:
BACK BURNER VENTURI:
1.
Remove set screw securing venturi wheel (located under firebox).
2.
Re-install set screw.
3.
Light fireplace and wait 15 minutes before determining if any further adjustments are
needed.
Venturi opening
Figure 18c
18
MAINTENANCE
The appliance is required to be inspected at least once a year by a professional service person.
The compartment below firebox must be cleaned at least once a year, more frequent cleaning may be required due to excessive lint from carpeting,
bedding materials, or other fibrous materials. Use a vacuum to clean all components at least once a year.
NOTE
INSTALLATION AND REPAIR SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE
INSPECTED BEFORE USE AND ANNUALLY BY A QUALIFIED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE
REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIALS, ETC. IT IS IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS AND CIRCULATION AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN .
CONTROL BOARD SYSTEM
Annual cleaning of burner system is required. Vacuum all components thoroughly.
The burner assembly may be removed for easier access. Refer to fireplace installation manual for complete instruction on removing &
reinstalling burner assembly.
Visually check for blocked port holes, especially near the pilot. Blocked port holes may cause delayed ignition.
Reinstall burner assembly following instructions in fireplace installation manual.
Visually check pilot light and burner when in operation. Flames should be steady, not lifting or floating.
Figure 19a
TMT-3875 Pilot
TMT-3875-MV Pilot
TMT-3875-IPI Pilot
Burner Orifice
Burner Ports
FAN
The fan should be disconnected from electrical current, and cleaned (vacuumed) every six months. The bearings are sealed and require no oiling.
VENT SYSTEM
Annual examination of venting system by a qualified agency is required.
IF VENT-AIR INTAKE SYSTEM IS DISASSEMBLED FOR ANY REASON, RE-INSTALL PER INSTRUCTIONS PROVIDED WITH INITIAL
INSTALLATION.
The flow of combustion and ventilation air must not be obstructed.
GLASS CLEANING & REPLACEMENT
Clean glass only when cool and only with non-abrasive cleansers.
WARNING: DO NOT OPERATE APPLIANCE WITH GLASS/FRAME ASSEMBLY REMOVED, CRACKED OR BROKEN. REPLACEMENT OF THE
GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR QUALIFIED SERVICE PERSON.
Use protective gloves to handle any broken or damaged glass assembly components.
The glass assembly, part #TMT-057T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co., Inc.
Replacement of glass & frame assembly, part #TMT-057T, must only be performed by a licensed or qualified service person.
DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass door assembly.
IMPORTANT
CAUTION
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
KEEP APPLIANCE AREA CLEAR OF COMBUSTIBLE MATERIALS, SUCH AS GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.
19
REPLACEMENT PARTS LIST
Replacement parts are available through your local dealer. Contact them for availability and pricing.
TMT-3875-MV CONTROL BOARD AND PARTS
TMT-700
Control Board - Nat Gas
700-403-1
Valve Step Motor - LP Gas
TMT-701
Control Board - LP Gas
700-203
Manual Shut-off Valve
700-084
SIT MV Valve - Natural
700-213B
18” Flexible Gas Line-Black
700-085
SIT MV Valve - LP
700-226
Flexible Gas Line-Valve to Burner Connection
700-088
Pilot Assembly - Natural Gas
700-230
Natural Gas Orifice #30
700-089
Pilot Assembly - LP Gas
700-245
LP Gas Orifice #45
700-308R
Receiver
NCK-TMTMV-S
Natural Gas Conversion Kit
700-558
GTMFS Wire Harness
LCK-TMTMV-S
LP Gas Conversion Kit
700-130
Fan Control Module
TMT-135
Burner Assembly
700-308
Transmitter
TMT-043
Pilot Shield
700-166
#62 Natural Gas Pilot Orifice
700-992
Pilot Igniter (with wire)
700-168
#35 LP Gas Pilot Orifice
700-993
Pilot Flame Sensor (with wire)
700-403S
Valve Step Motor - Natural Gas
TRF-200
Upper Hood
TMT-005
Replacement Valance
TRF-201
Lower Grill
900-006
1-1/8” Glass Gasket w/ Adhesive
TRF-200L
Upper Hood Louver
TMT-057T
Valance with 26” x 35” glass
TMT-500
Log Set
TMT-028-IPI
Fan Assembly
TMT-1
#1 Log
TMT-2
#2 Log
TMT-3
#3 Log
TMT-4
#4 Log
TMT-5
#5 Log
TMT-6
#6 Log
TMT-7
#7 Log
900-KLK
Klinkers
900-REMB
Rock Wool Embers
GLASS & GLASS GASKET
GRILL REPLACEMENT
FAN ASSEMBLIES
LOG SET
REFRACTORY REPLACEMENT
TMT-I900LS
Left Side Refractory Panel
TMT-I900RS
Right Side Refractory Panel
TMT-I901
Bottom Refractory Panel
TMT-900E
Ember / Log Refractory
Hussong Manufacturing Co., Inc.
P.O. Box 577
204 Industrial Park Drive
Lakefield, MN 56150-0577
USA
TMT-3875-MV
www.kozyheat.com
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising