Product data sheet 6EP1332-5BA00
Product data sheet
6EP1332-5BA00
SITOP PSU100C 24 V/2.5 A STABILIZED POWER SUPPLY
INPUT: AC 120-230 V (DC 110-300 V) OUTPUT: DC 24
V/2.5 A
Technical specifications
Product
SITOP PSU100C
Power supply, type
24 V/2.5 A
Input
Input
1-phase AC or DC
Rated voltage value Vin rated
100 … 230 V
Voltage range
85 … 264 V
Input voltage / at DC
110 … 300 V
Wide-range input
Yes
Overvoltage resistance
2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.
20 ms
Mains buffering
at Vin = 230 V
Rated line frequency
50 / 60 Hz
Rated line range
47 ... 63 Hz
Input current / at nominal level of the input voltage 100 V / nominal
value
1.21 A
Input current / at nominal level of the input voltage 230 V
0.67 A
Switch-on current limiting (+25 °C), max.
31 A
I²t, max.
2.4 A²·s
Built-in incoming fuse
internal
6EP1332-5BA00
Page 1/ 4
10/01/2012
subject to modifications
© Copyright Siemens AG 2012
Protection in the mains power input (IEC 898)
Recommended miniature circuit breaker: from 16 A, characteristic B
or from 10 A, characteristic C
Output
Output
Controlled, isolated DC voltage
Rated voltage Vout DC
24 V
Total tolerance, static ±
3%
Residual ripple peak-peak, max.
200 mV
Residual ripple peak-peak, typ.
55 mV
Spikes peak-peak, max. (bandwidth: 20 MHz)
300 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz)
50 mV
Adjustment range
22.2 … 26.4 V
Product feature / output voltage adjustable
Yes
Output voltage setting
via potentiometer
Status display
Green LED for output voltage OK
On/off behavior
Overshoot of Vout approx. 1 %
Startup delay, max.
0.7 s
Voltage rise, typ.
100 ms
Rated current value Iout rated
2.5 A
Current range
0 … 2.5 A
• Note
2.5 A up to +50 °C, 0.75 A up to +70 °C
delivered active power / typ.
60 W
Parallel switching for enhanced performance
Yes
• Note
Numbers of parallel switchable units for enhanced performance
Start-up with single nominal load only
2
Efficiency
Efficiency at Vout rated, Iout rated, approx.
87 %
Power loss at Vout rated, Iout rated, approx.
9W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max.
0.1 %
Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.
3%
Load step setting time 10 to 90%, typ.
4 ms
Load step setting time 90 to 10%, typ.
4 ms
Protection and monitoring
Output overvoltage protection
Yes, according to EN 60950
Current limitation, typ.
3A
Characteristic feature of the output / short-circuit protected
Yes
Short-circuit protection
Electronic shutdown, automatic restart
Overload/short-circuit indicator
-
Safety
6EP1332-5BA00
Page 2/ 4
10/01/2012
subject to modifications
© Copyright Siemens AG 2012
Primary/secondary isolation
Yes
Potential separation
Safety extra-low output voltage Uout acc. to EN 60950-1 and EN
50178
Protection class
Class I
stray current / maximum
3.5 mA
stray current / typical
0.4 mA
CE mark
Yes
UL/CSA approval
Yes
UL/cUL (CSA) approval
cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259;
cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
Explosion protection
ATEX (EX) II 3G Ex nA IIC T4; cCSAus (CSA C22.2 No. 213-M1987,
ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group ABCD, T4
FM approval
-
CB approval
Yes
Marine approval
GL and ABS in process
Degree of protection (EN 60529)
IP20
EMC
Emitted interference
EN 55022 Class B
Supply harmonics limitation
not applicable
Noise immunity
EN 61000-6-2
Operating data
Ambient temperature / in operation
-20 … +70 °C
• Note
with natural convection
Ambient temparature / on transport
-40 … +85 °C
Ambient temparature / in storage
-40 … +85 °C
Humidity class according to EN 60721
Climate class 3K3, no condensation
Mechanics
Connection technology
screw-type terminals
Connections / Supply input
L, N, PE: Removable screw terminal, each for 1 x 0.5 ... 2.5 mm²
Connections / Output
+: 1 screw terminal for 0.5 ... 2.5 mm²; -: 2 screw terminals for 0.5 ...
2.5 mm²
Connections / Auxiliary
-
Width / of the housing
45 mm
Height / of the housing
80 mm
Depth / of the housing
100 mm
Installation width
45 mm
Mounting height
180 mm
Weight, approx.
0.22 kg
Product feature / of the housing / housing for side-by-side mounting
Yes
Type of mounting / wall mounting
No
6EP1332-5BA00
Page 3/ 4
10/01/2012
subject to modifications
© Copyright Siemens AG 2012
Type of fixing / cap rail mounting
Yes
Type of mounting / S7-300 rail mounting
No
Installation
Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories
Removable spring-type terminal 6EP1971-5BA00
Other information
Specifications at rated input voltage and ambient temperature +25
°C (unless otherwise specified)
letzte Änderung:
Sep 10, 2012
6EP1332-5BA00
Page 4/ 4
10/01/2012
subject to modifications
© Copyright Siemens AG 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising