TECHNICAL DATA SHEET

TECHNICAL DATA SHEET
TECHNICAL DATA SHEET
Two-Component SPF Roof Patch Spray Foam
Handi-Foam Two-Component SPF Roof Patch Spray Foam is a
multiple purpose two-component polyurethane froth foam
designed within the international guidelines for protection of the ozone
layer, and with respect to the Montreal Protocol, 1987 and other
environmental guidelines, utilizing a non-flammable, non-ozone
depleting blowing agent to assist in the safety of the end user and
the environment. The pre-pressurized, portable two-component
froth systems are dispensed through the state-of-the-art HandiGun® froth dispensing unit, providing unsurpassed quality and flexibility in end-use performance.
Application Areas
Spray foam onto any clean, dry surface in any direction to insulate,
fill and seal various size voids, deaden sound or reduce vibration. It
is specifically designed to spray onto flat or irregular surfaces, and
to fill large cavities. Standard free-rise density for Handi-Foam SPF
Roof Patch II-75, II-145 and II-425 systems is 2.5 lbs/ft3 .
Properties
The patented and user-friendly II-75 and II-145 packaging system
provides many unique advantages, including:




Factory-attached dispensing hoses. No need to attach
hoses prior to use.
Handle is secured to tanks. No more handle popping out of
box. No more tanks falling out of the box when wet.
Easy to open box for immediate use.
Hoses extend from top of tanks. More reach. More stability.
The II-425 is packaged with the A component and B component in
separate boxes, due to the larger size.
Two-component froth foam systems will expand immediately upon
chemical reaction of A component and B component to a final
volume that is 3 to 5 times the dispensed volume, in typical applications, and may be as much as 8 times the dispensed volume in
specific applications, depending on various factors such as cavity
size, ambient conditions, etc. The foam will cure to a semi-rigid
closed cell foam upon the chemical reaction of component A
(polymeric isocyanate) with component B (a polyol blend containing
certain additives).
Handi-Foam SPF Roof Patch fully expands and dries tack-free
within 30 - 60 seconds, is cuttable in 2-5 minutes and fully cures
within 1 hour.
Handi-Foam adheres to almost all building materials with the
exception of surfaces such as polyethylene, Teflon®, silicone, oils
and greases, mold release agents and similar materials.
Optimum application temperature is 75°F (24°C) but may be
sprayed onto colder or warmer substrates, with slight effects on the
foam characteristics. Cured foam is resistant to heat and cold, -200
to +240°F (-129 to +115°C), and to aging, but not UV rays (i.e. sunlight) unless
painted, covered or coated. Cured PU
foam is chemically inert and non-reactive
in approved applications, and will not
harm electrical wire insulations, Romex®,
rubber, PVC, polyethylene (i.e. PEX),
CPVC or other plastic. It is approved for
use around wires, plumbing penetrations, etc., and contains no formaldehyde. Handi-Foam systems require no
outside mechanical or electrical power
source and are available in various
disposable kit sizes to meet specific job
application requirements. When
sprayed, the foam will create a seamless, continuous seal to insulate
and protect against dust, air infiltration
and pests.
Preparation For Use
Substrate must be clean, dry, firm, free of loose particles and free
of dust, grease and mold release agents. Protect surfaces not to be
foamed. Shake kits well before using.
Application / Use
After following instructions for set-up, kits are ready to use. Valves
must be in the upright position. Materials are dispensed through
hoses and mixed in the disposable nozzle.
With a nozzle attached to the Handi-Gun, dispense foam by
squeezing the trigger of the unit. To interrupt or stop foaming
process, release the trigger. Once foaming process has stopped,
the dispensing unit must be reactivated within 30 seconds or a new
nozzle must be installed (multiple nozzles included with each kit).
Fresh foam may be applied in several stages to reduce overfilling of
void or damage to non-rigid, confined cavities. Cured foam can only
be removed mechanically.
Important Note: Use only in well ventilated area or with certified
respiratory protection. Wear impervious gloves, protective eyewear
and suitable work clothes when using. Read all instructions and
safety information (MSDS) prior to use of any product. The product
contains no formaldehyde. Cured foam is non-toxic.
KEEP OUT OF REACH OF CHILDREN.
Product Storage
Store in cool dry area. Do not expose to open flame or
temperatures above 120°F (49°C). Excessive heat can cause
premature aging of components resulting in a shorter shelf life.
Handi-Foam is reusable by following product instructions.
2775 Barber Road
PO Box 1078
Norton, Ohio 44203 USA
p: 1 330.753.4585 1 800.321.5585 f: 1 330.753.5199
e: info@fomo.com w: www.fomo.com
A16141 © Fomo Products, Inc 2004 Rev. 09/08-0
Approvals / Standards
Technical Data
(Metric data shown in parentheses)
2.5 lbs/ft3
DENSITY
2.5 lbs/ft3
(40 kg/m3)
ASTM D-1622
K-FACTOR
ASTM C-518
(28 day aging)
R-VALUE
AIR BARRIER PROPERTIES
ASTM E-283
@6.24 psf (300 Pa)
@1.57 psf (75 Pa) extrapolated
PERM RATING
ASTM E-96
1" (2.54 cm)
TENSILE STRENGTH
ASTM D-1623
Parallel
TACK-FREE / EXPANSION TIME
CUTTABLE
FULLY CURED
FIRE RATING1
ASTM E-84
Handi-Foam package is patented under U.S. patent # 6,182,868.
0.165 BTU·inch/ft²·h·°F (0.024 W/m·K)
Dispensing gun is patented under U.S. patent #6,345,776. Other
foreign and domestic patents pending.
6.1/ inch
ODP (Ozone Depletion Potential): Contains non-ozone depleting,
non-flammable HFC Propellant.
<0.01 cfm/ft² (0.05 L/s/m²)
<0.0025 cfm/ft² (0.0125 L/s/m²)
VOC Content: Contains no VOC’s, according to currently accepted
definitions.
3.13 perms @ 1 inch thick
Theoretical Yield*
58 psi (400 kPa)
COMPRESSIVE STRENGTH
ASTM D-1621
Parallel @ 10%
40psi (275 kPa)
Perpendicular @ 10%
21 psi (145 kPa)
DIMENSIONAL STABILITY
ASTM D-2126
Heat age +158°F (70C)
+2.0%
+3.2%
Humid
age +158°F
(70C),
100%
RHtest methods, unless otherwise indicated.
All properties
obtained
using
internal
-0.2%
Cold age -4°F (-20C)
CLOSED CELL CONTENT
ASTM D-2856
“Class 2” refers to materials which will achieve a Flame Spread of 75
or less and a Smoke Developed rating of 450 or less when tested
according to ASTM E-84.
NONREFILLABLE
Board Feet
Cubic Feet
II-75
P10695
75
6.1 ft3
(.18 m3)
II-145
P10725
145
12 ft3
(.34 m3)
II-425
P10750
425
35 ft3
(1.0 m3)
>90%
30-60 seconds
2-5 minutes
1 Hour
Class 2
*Yields are based on theoretical calculations, for comparison
purposes, and will vary depending on ambient conditions and
particular application. Model number generally reflects board feet
volume in each kit.
Always read all operating, application and safety instructions before using any products. Use in conformance with all local, state and federal regulations and safety requirements.
Failure to strictly adhere to any recommended procedures and reasonable safety precautions shall release the manufacture of all liability with respect to the materials or the use thereof.
NOTE: Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory conditions and may vary upon
use, temperature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. This information supersedes all previously published data.
Yields shown are based on theoretical calculations and will vary depending on ambient conditions and particular application. Read all product directions and safety information before use. This
product is organic and therefore may constitute a fire hazard if improperly installed. Consult local building codes for specific requirements regarding the use of cellular plastics or urethane
products in construction.
WARNINGS: Follow safety precautions and wear protective equipment as recommended. Consult Material Safety Data Sheet (MSDS) for specific information. Prolonged inhalation exposure
may cause respiratory irritation/sensitization and/or reduced pulmonary function in susceptible individuals. Onset may be delayed. Pre-existing respiratory conditions may be aggravated. Use
only with adequate ventilation or certified respiratory protection. NIOSH approved positive pressure supplied air respirator or a negative pressure half mask with organic vapor cartridge and
dust/mist prefilters is recommended if exposure guidelines may be exceeded. Contents may be very sticky and irritating to skin and eyes, therefore wear protective eyewear, impervious gloves,
and suitable work clothes when operating. If liquid chemical comes in contact with skin, first wipe thoroughly with dry cloth, then rinse affected area with water. Wash with soap and water afterwards, and apply hand lotion if desired. If liquid comes in contact with eyes, immediately flush with large volume of clean water for at least 15 minutes and get medical help at once. If liquid is
swallowed, get immediate medical attention. Products manufactured or produced from these chemicals may present a serious fire hazard if improperly used or allowed to remain exposed or
unprotected. Each user of any product should carefully determine whether there is a potential fire hazard associated with such product in a specific usage. KEEP OUT OF REACH OF
CHILDREN.
LIMITED WARRANTY: The Manufacturer warrants only that the product shall meet its specifications: This warranty is in lieu of all written or unwritten, expressed or implied warranties and the
manufacturer expressly disclaims any warranty of merchantability, or fitness for a particular purpose. The buyer assumes all risks whatsoever as to the use of the material. Buyer’s exclusive
remedy as to any breach of warranty, negligence or other claim shall be limited to the replacement of the material. Failure to strictly adhere to any recommended procedures shall release The
manufacturer of all liability with respect to the materials or the use thereof. User of this product must determine suitability for any particular purpose, including, but not limited to, structural requirements, performance specifications and application requirements prior to installation and after product is applied.
Two-Component SPF Roof Patch Spray Foam
Fomo Products, Inc. p: 1 330.753.4585, 1 800.321.5585 f: 1 330.753.5199
e: info@fomo.com www: fomo.com
A16141 © Fomo Products, Inc 2004 Rev. 09/08-1
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising