F250 Vision Sensor SETUP MANUAL Cat. No. SCHB-736A-D1

F250 Vision Sensor SETUP MANUAL Cat. No. SCHB-736A-D1
Cat. No. SCHB-736A-D1
F250
Vision Sensor
SETUP MANUAL
)9LVLRQ6HQVRU
)&&
0DQXDO6HWXS0DQXDO
3URGXFHG6HSWHPEHU
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always
heed the information provided with them. Failure to heed precautions can result in injury to people
or damage to property.
!DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
!WARNING Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
!Caution
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, or property damage.
OMRON Product References
All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it
refers to an OMRON product, regardless of whether or not it appears in the proper name of the
product.
Visual Aids
The following headings appear in the left column of the manual to help you locate different types
of information.
Note
1,2,3...
Indicates information of particular interest for efficient and convenient operation of the product.
,QGLFDWHVOLVWVRIRQHVRUWRUDQRWKHUVXFKDVSURFHGXUHVFKHFNOLVWVHWF
Precaution
Indicates information required to take full advantage of the functions and performance of the product. Incorrect application methods may result in the loss
of damage or damage to the product. Read and follow all precautionary information.
CHECK
Indicates points that are important in using product functions or in application
procedures.
TwoCamera
SeeAlso
HELP
Indicates information required when using a 2-camera system.
Indicates where to find related information.
Indicates information helpful in operation, such as the definition of terms.
¸ OMRON, 2001
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise,
without the prior written permission of OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information contained
in this manual is subject to change without notice. Every precaution has been taken in the preparation
of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions. Neither is
any liability assumed for damages resulting from the use of the information contained in this publication.
v
TABLE OF CONTENTS
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
1
Special or Critical Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
2
General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
3
Regulations and Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
SECTION 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-1
Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-2
Confirming Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-3
Product Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION 2
Special Features, Installation, and Connections . . . . . . . . . . . . 7
2-1
Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2-2
Basic System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-3
Component Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2-4
Mounting the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2-5
Connecting Peripheral Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2-6
Power Supply and Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SECTION 3
Lenses, Lighting, and Memory Cards. . . . . . . . . . . . . . . . . . . . 21
3-1
CCTV Lenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3-2
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3-3
Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SECTION 4
Connecting External Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4-1
Connecting through the Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4-2
Connecting through the Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SECTION 5
Troubleshooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . 43
5-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5-2
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5-3
Regular Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5-4
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5-5
F200/F300 Camera Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5-6
Connecting a Strobe Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
vii
$ERXWWKLV0DQXDO
This manual describes the hardware for the F250 Vision Sensor and how to install the components, and it includes the sections described below. This is one of two manuals used to
operate the F250. Refer to the following table for the contents of each manual.
Manual
1: Setup Manual
Contents
Provides information on system hardware and installation. Be sure to read this manual first.
2: Operation Manual The Operation Manual CD-ROM is packed with the
(on CD-ROM)
F250-UME Application Software. This manual explains
basic operations such as installing the Application Software, setting up inspection processes, and communicating with external devices.
Cat. No.
SCHB-736A
Z153-E1-01
Please read the above manuals carefully and be sure you understand the information provided before attempting to install or operate the F250.
Section 1 Introduction describes the precautions that must be taken when installing and
operating the F250 Vision Sensor.
Section 2 Special Features, Installation, and Connections shows a basic F250 system
configuration and explains how to install the F250 and connect it to a power supply and
peripheral devices.
Section 3 Lenses, Lighting, and Memory Cards describes how to select and use these
components most effectively.
Section 4 Connecting External Devices describes how to connect external devices
through a parallel interface (the parallel connectors) or serial interface (the RS-232C/RS422 connector or Ethernet connector).
Section 5 Troubleshooting and Maintenance provides tables to help identify and correct
hardware errors that may occur with the F250 as well as information on maintenance and
periodic inspections.
!WARNING Failure to read and understand the information provided in this manual may result in personal injury or death, damage to the product, or product failure. Please read each section in
its entirety and be sure you understand the information provided in the section and related
sections before attempting any of the procedures or operations given.
ix
PRECAUTIONS
This section provides general precautions for using the F250 Vision Sensor.
The information contained in this section is important for the safe and reliable application of the F250
Vision Sensor. You must read this section and understand the information contained before attempting to
set up or operate an F250 Vision Sensor.
1
2
3
Special or Critical Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulations and Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xii
xii
xiii
xi
1
Special or Critical Applications
1
Special or Critical Applications
When the F250 will be used in one of the conditions or applications listed
below, allow extra safety margins in ratings and functions, add extra safety features such as fail-safe systems, and consult your OMRON representative.
• Operating conditions or environments which are not described in the
manual
• Nuclear power control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement equipment, or
safety equipment
• Other systems, machines, and equipment that may have a serious influence on lives and property and require extra safety features
2
General Safety Precautions
Battery Precautions
!WARNING Do not disassemble the F250, apply pressure to the F250 that would deform
its shape, or incinerate the F250. A lithium battery is built into the F250 and it
may combust, explode, or burn if not treated properly.
!WARNING Do not short circuit, attempt to charge, disassemble, apply pressure that would
deform, or incinerate the lithium battery. The lithium battery may start a fire,
explode, or burn if not treated properly.
Installation Environment Precautions
!Caution Do not use the F250 in environments with flammable or explosive gases.
!Caution Install the F250 away from high-voltage devices and moving machinery to
allow safe access during operation and maintenance.
!Caution Install the F250 so that air can flow freely through its cooling vents. If the vents
are blocked, heat will build up in the Controller and may cause burns.
Intake vent
Exhaust vent
!Caution Be sure to securely tighten the screws when mounting the F250.
Power Supply and Wiring Precautions
!Caution Use the F250 with the power supply voltages specified in this manual.
!Caution Use the wire and crimp terminals of the proper sizes as specified in this manual. Do not connect the power supply wires by just twisting stranded wire and
connecting directly to the terminals.
!Caution Use a DC power supply with countermeasures against high-voltage spikes
(safe extra low-voltage circuits on the secondary side).
xii
Regulations and Standards
Note
1.
Keep the power supply wires as short as possible (Max. 10 m).
2.
Ground the F250’s ground terminal to less than 100 W.
3.
Use a grounding point as close as possible to the F250 and keep the
ground line as short as possible.
4.
Wire the F250 to the ground with a separate ground wire. To avoid grounding problems, do not share the ground wiring with any other devices or
ground the F250 to the building’s steel framing/plumbing.
3
Other Precautions
!Caution Do not attempt to dismantle, repair, or modify the F250.
!Caution Do not touch fluorescent or halogen lights while the power is ON or immediately after the power is turned OFF. These lights get very hot and can cause
burns.
!Caution If you suspect an error or malfunction, stop using the F250 immediately, turn
OFF the power supply, and consult your OMRON representative.
Note Dispose of the F250 as industrial waste.
3
Regulations and Standards
The F250 complies with the EC Directive and EN standard below.
1.
EC Directives
EMC Directive: No. 89/336/EEC
2.
EN Standards (European Standards)
EN 61326: 1997/Annex A+A1: 1998 (EMI: Class A)
xiii
SECTION 1
Introduction
This section describes the precautions that must be taken when installing and operating the F250 Vision Sensor.
1-1
Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1-1-1
Controller Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1-1-2
Component Installation and Handling . . . . . . . . . . . . . . . . . . . . . . .
4
1-2
Confirming Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
1-3
Product Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
1
Section 1-1
Installation Precautions
1-1
Installation Precautions
The F250 is highly reliable and resistant to most environmental factors. The
following guidelines, however, must be followed to ensure reliability and optimum use of the F250.
!Caution Read the Precautions section before proceeding with installation or operation.
1-1-1
Controller Installation
Installation Site
Do not install the F250 in locations subject to the following conditions:
1,2,3...
1.
Ambient temperatures outside of the 0 to 50•C (32 to 122•F) range
2.
Rapid temperature fluctuations (likely to cause condensation)
3.
Relative humidities outside of the 35% to 85% range
4.
Presence of corrosive or flammable gases
5.
Presence of dust, salt, or iron particles
6.
Direct vibration or shock
7.
Direct sunlight
8.
Water, oil, or chemical fumes or spray
Orientation of Controller
To improve heat dissipation, install the Controller in the following orientation
only. For proper air flow, provide at least 20 mm of clearance above the Controller and at least 50 mm of clearance on both sides.
• Horizontal Installation
CORRECT
Do not install the Controller upside down as shown in the following diagram.
INCORRECT
2
Section 1-1
Installation Precautions
• Vertical Installation
The Controller can be installed vertically with the air intake at the bottom
and exhaust at the top. For proper air flow, provide at least 20 mm of clearance at the top of the Controller and at least 50 mm of clearance on both
sides (the intake and exhaust sides).
CORRECT
INCORRECT
Exhaust
Intake
Intake
Exhaust
Ambient Temperature
1,2,3...
1.
For proper air flow, maintain a minimum clearance of 20 mm at the top of
the F250 and at least 50 mm of clearance at the sides where the cooling
air intake and exhaust are located.
2.
Do not install the F250 immediately above significant heat sources, such
as heaters, transformers, or large-capacity resistors.
3.
Do not let the ambient operating temperature exceed 50•C (122•F).
4.
Provide a forced-air fan cooling or air conditioning if the ambient temperature is near 50•C (122•F) so that the ambient temperature never exceeds
50•C (122•F).
Control panel
F250
Louver
3
Section 1-1
Installation Precautions
Noise Resistance
Use the following measures to help increase noise resistance.
1,2,3...
1.
2.
Do not install the F250 in a cabinet containing high-voltage equipment.
Do not install the F250 within 200 mm of power cables.
Power lines
200 mm min.
200 mm min.
F250
1-1-2
Component Installation and Handling
OMRON Components
Use a Camera, Camera Cable, and Console designed specifically for the
F250.
Connecting Cables
Always turn OFF the F250’s power before connecting or disconnecting a camera or cable.
Handling the Camera
The Camera’s case is connected to the 0V line in the internal circuits. Observe
the following precautions to prevent noise interference.
1,2,3...
1.
Do not ground the Camera.
2.
Do not remove the base attached to the Camera.
3.
Do not remove the ferrite core attached to the F150-VS or [email protected]@
Camera Cable.
Securing the Video Monitor (When Using the Recommended F150-M09)
Observe the following precautions to prevent noise interference, because the
video monitor case is connected to the 0V line in the internal circuits.
1,2,3...
1.
Do not ground the video monitor.
2.
Do not ground the metallic part of the connector.
3.
Secure the video monitor with plastic screws if it is being mounted to a metallic surface.
Touching Signal Lines
To prevent damage from static electricity, use a wrist strap or another device
for preventing electrostatic discharges when touching terminals or signal lines
in connectors.
Handling the Memory Card
• To prevent damage from static electricity, do not touch the Memory Card
directly while it is installed in the F250.
• To remove a Memory Card, turn OFF the power supply to the Card (using
the menu command) or turn OFF the F250. Press the eject button to eject
the Card. The Memory Card or the F250 itself may be damaged if a Memory Card is removed while power is being supplied.
Note F250-UME Precautions
It will not be possible to start the Setup Menu if you change the contents of the
Memory Card after installing it in a personal computer or other device. Never
4
Section 1-1
Installation Precautions
change the contents of the Card with operations such as the following:
• Changing file names
• Moving or deleting files
• Overwriting data
• Formatting
Turning OFF the Power
Do not turn OFF the power while a message is being displayed indicating that
processing is being performed. Data in memory will be corrupted, and the
F250 may not operate correctly the next time it is started.
0.Scn 0
MON
---- ---ms
Saving data.
Using the RESET Signal
Do not use the RESET input immediately after power is turned ON. When
using the RESET input to synchronize startup timing, wait at least 1 second
after the F250's power supply is turned ON before turning ON the RESET signal.
Replacing the Battery
The F250 is equipped with a battery that backs up the clock. When the battery
is low, the message “BATTERY LOW” will be displayed on the monitor at startup. The battery must be replaced when this message is displayed. Return the
F250 to your OMRON dealer for service. (The battery is not user-serviceable.)
The battery will last approximately 7 years.
5
Section 1-2
Confirming Package Contents
1-2
Confirming Package Contents
Check the contents of the package as soon as you receive the F250. It is
extremely rare for components to be missing, but contact the nearest OMRON
representative if any of the following items are missing.
1,2,3...
CHECK
1-3
1.
F250 Vision Mate Controller
Qty.: 1
2.
Ferrite core for F150-KP Console or F160-KP Console
Ferrite core for F150-VM Monitor Cable
3.
Setup Manual (this manual)
Qty: 1
Qty: 1
Qty.: 1
The F250 Vision Sensor Manual 2: Operation Manual (on CD-ROM) is packed
with the F250-UME Application Software.
Product Availability
Some of the products listed may not be available in some countries. Please
contact your nearest OMRON sales office by referring to the addresses provided at the back of this manual.
6
SECTION 2
Special Features, Installation, and Connections
This section describes some of the special features of the F250, shows a basic F250 system configuration, and
explains how to install and wire the F250.
2-1
Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
2-1-1
Problems Solved with a New Algorithm . . . . . . . . . . . . . . . . . . . . .
9
2-1-2
Simple and Flexible Inspection Settings . . . . . . . . . . . . . . . . . . . . .
11
2-1-3
Smooth Switching between Processes . . . . . . . . . . . . . . . . . . . . . . .
11
2-2
Basic System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
2-3
Component Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
2-4
Mounting the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
2-4-1
Horizontal Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
2-4-2
Vertical Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Connecting Peripheral Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
2-5-1
Connecting a Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
2-5-2
Connecting a Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
2-5-3
Connecting a Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Power Supply and Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
2-6-1
Crimp Terminals and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
2-6-2
Ground (Earth) Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
2-6-3
Wiring the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
2-5
2-6
7
Section 2-1
Special Features
2-1
Special Features
The F250 Vision Sensor uses a camera instead of the human eye to process
images and inspect products. Visual inspections can be automated to perform
complicated inspections quickly and accurately.
There were problematic cases in which Vision Sensors could not detect differences that could be detected by the human eye. The F250 is a high-performance Vision Sensor that solves many of these problems.
8
Section 2-1
Special Features
2-1-1
Problems Solved with a New Algorithm
EC Defect Inspection
Detect minute damage,
dirt, or deformation!
Dirt on a
deformed ring
Chipped
Good
Quest Optical Character Verification
Verify expiration data and
lot number!
Detect incorrect font size/
style as well as errors.
Good
01.01.28
It is possible to inspect for different font styles and sizes.
Size
01.01.28
Italic
Width
01.01.28
Blurred
Interrupted
01.01.28
Bold
01.01.28
01.01.28
01.01.28
9
Section 2-1
Special Features
EC Positioning
Very precise positioning
and positioning of lowcontrast objects.
Positioning mark
Low contrast
Internal defect
Fine matching
Inspect for blurred
characters or graphics!
Find differences from the
model image.
Model image
Measured image
Dirt on design
Chip on edge
Minute dirt
Omission
The F250 has many other inspection processes in its line-up.
10
Section 2-1
Special Features
2-1-2
Simple and Flexible Inspection Settings
First, install the required inspection processes from the Application Software
Memory Card.
F250-UME Application Software
Processes in the menu can be combined freely.
0.Scn 0=SET=
0.Camera image
1.EC pos. comp
2.Fine matching
3.Binary defect
4.DO data
5.
ENT:Set SFT+ESC:Edit
2-1-3
Smooth Switching between Processes
The scene function can be used to set up to 32 different inspections. When the
inspection requirements change, the inspection process can be changed just
by changing the scene. Up to 1,024 scenes can be stored on a 128-MB Memory Card.
11
Section 2-2
Basic System Configuration
2-2
Basic System Configuration
The following diagram shows the basic F250 system configuration.
Precaution
Some of the components shown in the configuration diagram are special
OMRON products that cannot be substituted with comparable devices. These
items are indicated with an asterisk.
Monitor
Monitor with
S-VIDEO input
F150-M05L Color
LCD Monitor
(RCA plug input)
Use the Monitor to check
images and display the
condition-setting menus.
S-VIDEO Input Cable
(Use a standard cable.)
F150-M09 Monochrome
CRT Video Monitor
(BNC input)
BNC Jack
(Included with the
F150-VM Monitor
Cable.)
F150-VM Monitor
Cable (2 m)
Console
F150-KP
F160-KP
(2-m cable) (2-m cable)
Controller
This is the F250 Controller itself.
The F250 performs the image
processing specified by the user
settings and outputs the
measurement results.
Power
Supply
We recommend the
OMRON S82K-10024.
See page 20 for details.
12
*F150-VS Camera
Cable (3 m)
Section 2-2
Basic System Configuration
*Cameras
The Camera captures images of the
measurement objects. Up to 4 Cameras
can be connected to one F250 Controller.
CHECK
If [email protected]@@ or [email protected]@@ Cameras are being used, the connected
Cameras must belong to the same series, i.e., they must have the
same model number prefix (F150 or F160).
• Double-speed Cameras
Camera with Intelligent Lighting
Camera Only
F160-SLC20 (20-mm field of vision)
F160-SLC50 (50-mm field of vision)
F160-S1
Use the Camera by itself when the field of
vision of the [email protected] does not match the
size of the measurement object. A standard
CCTV lens and light source will be needed.
• F150 Cameras
Camera with Intelligent Lighting
Camera with Intelligent Lighting
F150-SLC20 (20-mm field of vision)
F150-SLC50 (50-mm field of vision)
F150-SL20A (20-mm field of vision)
F150-SL50A (50-mm field of vision)
Camera Only
F150-S1A
Use the Camera by itself when the field of
vision of the [email protected] does not match the
size of the measurement object. A standard
CCTV lens and light source will be needed.
CHECK
F200-series and F300-series Cameras can also be connected. Up to four
Cameras can be connected, but they must all have the same model number.
Only one Camera can be connected, however, when the F200-S Camera is
used or when a camera with an internal sync mode is used.
Camera type
Camera Cable
Max. number of Cameras
F200-S
F160-VSR3
F300-S
F160-VSR4
1 (Connect to camera connector 0.)
4
F300-S2R
F160-VSR3
(The Cameras must have the same model number.)
F300-S3DR
F300-S4R
SeeAlso
Refer to page 68 for details on parameter settings.
13
Component Names and Functions
2-3
Section 2-3
Component Names and Functions
The following diagram shows the F250 Controller’s major components.
1.
RS-232C/RS-422 Connector
Connects the F250 to an external device such as a personal computer or
PLC.
2.
Ethernet Connector (10BASE-T)
Connects the F250 to a personal computer. (Can be used with F250-UME
Application Software version 1.10 or higher.)
3.
Monitor Connector (S-VIDEO Output)
Connects to a monitor with an S-VIDEO input.
4.
Monitor Connector (Composite Video Output)
Connects to a monitor.
5.
Memory Card Slots 0 and 1
Memory Cards such as the Application Software Memory Card can be inserted in these slots.
6.
Memory Card Indicators 0 and 1
Lit when power is being supplied to the corresponding Memory Card. (The
Memory Card must not be inserted or removed when this indicator is lit.)
7.
Console Connector
Connects the F250 to a Console.
8.
ERROR Indicator
Lit when an error has occurred.
9.
RUN Indicator
Lit while the F250 is in Run Mode.
10. POWER Indicator
Lit while power is ON.
11. Parallel Connectors 0 and 1
Connect the F250 to external devices such as a sync sensor or PLC.
12. Camera Connectors 0 to 3
Connect to the Cameras.
13. Ground Terminal
Connects to the ground wire.
14. Power Supply Terminals
Connect to the DC power supply.
14
Section 2-4
Mounting the Controller
2-4
Mounting the Controller
There are two ways to mount the Vision Mate Controller: horizontal mounting,
or vertical mounting. (All dimensions are in mm.)
F250 Dimensions
This screw hole
cannot be used.
115 min.
8
73
270
220–0.6
Four M4 taps
(for mounting)
Stopper
10 to 13
Panel
thickness: T
The screw length L must be
in the following range:
10+T < L < 13+T
136 0.5
(25)
197
–
(40)
2-4-1
(14)
CHECK
190–0.6
Use the correct screw length. If
the screw extends more than 13
mm past the panel, the stopper
may bend and contact the
Controller’s internal PC board.
Horizontal Mounting
For proper air flow, provide at least 20 mm of clearance from the top of the
Controller and at least 50 mm of clearance from the sides (next to the intake
and exhaust vents).
This screw hole
cannot be used.
115 min.
20 min.
20 min.
50 min.
(Intake)
50 min.
(Exhaust)
8 mm
15
Section 2-4
Mounting the Controller
2-4-2
Vertical Mounting
For proper air flow, provide at least 20 mm of clearance from the top of the
Controller and at least 50 mm of clearance from the sides (next to the intake
and exhaust vents).
50 min.
(Exhaust)
115 min.
20 min.
20 min.
50 min.
(Intake)
Precaution
View from bottom
The Controller must be installed with the air intake side down and the air
exhaust side up.
Incorrect
Correct
Exhaust
Intake
16
Intake
Exhaust
Section 2-5
Connecting Peripheral Devices
2-5
Connecting Peripheral Devices
This section shows how to connect peripheral devices to the F250.
Precaution
Always turn OFF the power supply before connecting or disconnecting a
peripheral device’s cable. The peripheral device may be damaged if it is connected while the power is ON.
The various connectors on the F250 are capped when the F250 is shipped.
When a connector is not being used, leave the cap in place or replace the cap
to protect against dust, dirt, and static electricity.
2-5-1
Connecting a Console
Connect the Console to the F250’s CONSOLE connector. An F160-KP or
F150-KP Console can be connected. Install the provided ferrite core onto the
cable, positioning the ferrite core about 10 mm from the F250-side connector.
SHIFT
ENT
ESC
TRIG
Approx. 10 mm
Ferrite core
CONSOLE
2-5-2
Connecting a Monitor
Connect the monitor cable to the F250’s MONITOR connector. Install the provided ferrite core onto the F150-VM Monitor Cable, positioning the ferrite core
about 10 mm from the F250-side connector. The S-VIDEO and VIDEO outputs
can be used simultaneously.
Ferrite core
POWER
SYNC
VIDEO
Approx. 10 mm
S-VIDEO
2-5-3
Connecting a Camera
Connect the camera cable to the F250's CAMERA connector.
CAMERA
Overview of Available Cameras
The F250 Camera with Light is a special Camera that has a special lens and
light source already attached. The light source and lens are contained in a sin-
17
Section 2-5
Connecting Peripheral Devices
gle unit, so installation is very simple. Just mount the Camera at the proper
distance from the measurement object and it is ready to use.
Camera with Light
Item
F150-SL20A
F150-SL50A
Field of vision
20 mm ™ 20 mm
50 mm ™ 50 mm
Mounting distance
61 to 71 mm
66 to 76 mm
Relationship
between Camera
and object
Mounting distance
Measurement
object
Field of vision
Lighting precautions
None in particular
Camera with Intelligent Lighting
Item
F150-SLC20 or F160-SLC20
F150-SLC50 or F160-SLC50
Field of vision
20 mm ™ 20 mm
50 mm ™ 50 mm
Mounting distance
15 to 25 mm
16.5 to 26.5 mm
Relationship
between Camera
and object
Mounting distance
Measurement
object
Field of vision
Use with DIP switch pins 1 and 2 both set to Use with DIP switch pins 1 and 2 both set to
OFF.
OFF.
O
F
F
1
2
O
N
↑
1
2
Lighting precautions
Camera Only
Item
F150-S1A or F160-S1
Field of vision and
distance to object
Determine the required field of vision based on the size of the measurement object and
select an appropriate CCTV lens (C mount).
Lighting precautions
Provide a light source appropriate for the measurement object.
CHECK
18
Observe the following precautions when using a Camera with Light or Camera
with Intelligent Lighting.
Section 2-6
Power Supply and Ground
• The lens has a fixed focal point. The actual field of vision and focal point
vary from lens to lens, so adjust the distance to the measurement object
after replacing the lens or camera.
• The camera mounting distance listed in the following tables is an approximate value. Mount the Camera so that the distance to the measurement
object can be adjusted easily.
If the object size and field of vision are incompatible, use a standard CCTV
lens and light source.
SeeAlso
2-6
page 22
Power Supply and Ground
Wire the power supply and the ground to their respective terminals. Tighten
the screws to a torque of between 0.49 N¼m.
After wiring, confirm that the wiring is correct.
2-6-1
Crimp Terminals and Cables
The terminal block uses M3 terminal screws. Use appropriate crimp terminals
for M3 screws, as shown below.
Forked
Round
6.2 mm max.
6.2 mm max.
Applicable wire size: Insulated wire of 1.31 to 1.65 mm2 (AWG16 to AWG15)
2-6-2
Ground (Earth) Wiring
Always connect a ground wire to the F250's ground terminal. To avoid grounding problems, do not share the ground wire with any other devices or wire the
ground to the building's steel framing.
Use a grounding point that is as close as possible and keep the ground wire as
short as possible.
Ground to 100 W or less
19
Section 2-6
Power Supply and Ground
2-6-3
Wiring the Power Supply
Wire the Power Supply Unit independently of other devices. In particular, keep
the power supply wired separately from inductive loads. Also, keep the power
supply wiring as short as possible (less than 10 m).
Use a power supply that meets the following specifications. We recommend
using OMRON’s S82K-10024 Power Supply.
Item
CHECK
Specification
Output current
3.7 A min.
Power supply voltage
24 VDC +10%/-15%
Use a DC power supply with countermeasures against high voltages (safe
extra low-voltage circuits on the secondary side). If the system must meet UL
standards, use a UL class II power supply.
+
−
24 VDC
!Caution Keep the power supply line as short as possible (less than 10 m).
After wiring, replace the protective cover on the power supply terminals.
20
SECTION 3
Lenses, Lighting, and Memory Cards
This section provides additional information on CCTV lenses, lighting, and Memory Cards.
3-1
3-2
3-3
CCTV Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
3-1-1
Optical Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
3-1-2
Lenses and Lens Diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
3-1-3
Extension Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
3-2-1
Lighting Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
3-3-1
Installing a Memory Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
3-3-2
Removing the Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
3-3-3
Using Memory Cards in a Personal Computer. . . . . . . . . . . . . . . . .
28
21
Section 3-1
CCTV Lenses
3-1
CCTV Lenses
When using a Camera without a light (F150-S1A or F160-S1), refer to the following graph to select the appropriate Lens and Extension Tube. The lens will
differ depending on the size of the measurement object and the distance from
the Camera.
3-1-1
Optical Chart
The values in the following chart are approximations, and the Camera must be
adjusted after it is mounted.
Camera distance A (mm)
Lens model: 3Z4S-LE
5,000
3,000
2,000
1,000
500
300
200
t: Extension Tube length
100
50
4 5
10
20
30
50
100
200
300
500
Field of vision L (mm)
The X axis of the graph shows field of vision L (mm), and the Y axis shows the
camera distance A (mm). The curves on the graph show the relationship
between the field of vision and camera distance for each CCTV lens. The values are significantly different for each lens, so double-check the model of the
lens before using the graph. The “t” values indicate the lengths of the Extension Tubes. The value “t0” shows the case where an Extension Tube is not
needed and the value “t5.0” shows the case where a 5-mm Extension Tube is
used.
22
Section 3-1
CCTV Lenses
Example
When a 3Z4S-LE C1614A CCTV Lens is being used and a field of vision of
40 mm is needed at the measurement object, a camera distance of 200 mm
and 1-mm Extension Tube are required.
Camera
Extension Tube [email protected] (mm)
Lens
Camera distance A (mm)
Measurement object
Field of vision L (mm)
3-1-2
Lenses and Lens Diameters
Unit: mm
1"-32UN 30 dia.
-2A
Max. outer dia.
Total length
Lens
Focal length
Brightness
Maximum outer
diameter
Total length
3Z4S-LE C418DX
4.8 mm
F1.8
40.5 mm dia.
35.5 mm
3Z4S-LE B618CX-2
6.5 mm
F1.8
48 mm dia.
42 mm
3Z4S-LE C815B
8.5 mm
F1.5
42 mm dia.
40 mm
3Z4S-LE B1214D-2
12.5 mm
F1.4
42 mm dia.
50 mm
3Z4S-LE C1614A
16.0 mm
F1.4
30 mm dia.
33 mm
3Z4S-LE B2514D
25.0 mm
F1.4
30 mm dia.
37.3 mm
Filter size
--M40.5 ™ P0.5
M27 ™ P0.5
3Z4S-LE B5014A
50.0 mm
F1.4
48 mm dia.
48 mm
M46 ™ P0.75
3Z4S-LE B7514C
75.0 mm
F1.4
62 mm dia.
79 mm
M58 ™ P0.75
23
Section 3-1
CCTV Lenses
3-1-3
Extension Tubes
One or more Extension Tubes can be inserted between the lens and the Camera to focus the Camera image. Use a combination of one or more of the six
tubes to achieve the required length.
Extension Tube
Model
3Z4S-LE EX-C6
Maximum outer
diameter
31 dia.
Length
Set of 6 tubes
0.5 mm, 1 mm, 5 mm, 10 mm, 20 mm, and
40 mm
Length: 40 mm
Precaution
20 mm
10 mm
5 mm 1.0 mm 0.5 mm
• Do not use the 0.5-mm and 1.0-mm Extension Tubes attached to each
other. Since these Extension Tubes are placed over the threaded section
of the Lens or other Extension Tube, the connection may loosen when
more than one 0.5-mm or 1.0-mm Extension Tube are used together.
• Reinforcement may be required for combinations of Extension Tubes
exceeding 30 mm if the Camera is subject to vibration.
24
Section 3-2
Lighting
3-2
Lighting
A stable image must be obtained to ensure accurate inspection. Use appropriate lighting for the application and the measurement object if using a Camera
without a light (F150-S1A or F160-S1).
3-2-1
Lighting Methods
Back Lighting
A stable, high-contrast image can be obtained using back lighting.
Applications: Inspection of exterior shape or positioning inspection
Camera
Measurement object
Light source
Reflected Lighting
Ring Lights
Light is shone uniformly on the measurement object.
Applications: Surface inspections
Camera
Light source
Measurement object
Oblique Lighting
Detection can be made utilizing the difference in regular and diffuse reflected
light.
25
Section 3-2
Lighting
Applications: Inspections for surface gloss
Camera
Light source
Measurement object
Coaxial Lighting
A stable image can be obtained with few shadows from uneven surfaces on
the measurement object.
Applications: Surface inspections, positioning, and hole inspections of comparatively small objects
Camera
Half mirror
Light source
Measurement object
26
Section 3-3
Memory Cards
3-3
Memory Cards
Use a Memory Card to back up data such as settings and image data or
increase the number of scenes when you are using the Scene Group function.
Data from the F250 can be backed up in the computer just by inserting the
Memory Card into the computer and copying the desired data. The following
procedures also apply to the Memory Card containing the F250-UME Application Software.
We recommend the OMRON F160-N64S (64 MB).
CHECK
The F250 is equipped with two Memory Card slots. Use these slots for the following functions.
Function
F250-UME Application Software installation
Precaution
3-3-1
Memory Cards for scene groups
Slot 1 (Use slot 1 only.)
Memory Cards for data backup
Either slot 0 or 1 can be used.
A filler card with no memory is inserted into the F250’s Memory Card slot
before the F250 is shipped. Remove this filler card and install a Memory Card
to use the Memory Card functions.
If Memory Cards are not being used, leave the filler card in place to prevent
dust or dirt from entering the Memory Card slot.
Installing a Memory Card
1.
CHECK
3-3-2
Slot number
Slot 0 (Use slot 0 only.)
Insert the Memory Card into the Memory Card slot.
The eject button will pop out slightly when the Memory Card is inserted
properly.
Removing the Memory Card
1.
SeeAlso
Turn OFF the power supply to the Memory Card or turn OFF the F250.
Refer to Section 4 Additional Functions in the F250 Vision Sensor Manual
2: Operation Manual for details on turning OFF the power supply to the
Memory Card.
2.
Verify that the Memory Card indicator is not lit.
Memory card indicator
27
Section 3-3
Memory Cards
Precaution
Do not remove the Memory Card if the Memory Card indicator is lit. Doing
so may damage the Memory Card or the F250 itself.
3.
Precaution
Press the eject button to the right of the Memory Card slot. The Memory
Card will pop out slightly.
Do not remove the Memory Card without pressing the eject button. Doing so
may damage the F250.
Memory card eject button
4.
3-3-3
Pull the Memory Card straight out from the slot.
Using Memory Cards in a Personal Computer
The F250’s Memory Cards can be used in a personal computer with a PC
Card drive (PCMCIA 2.0 or higher, type II compatible) or CompactFlash™
drive.
The Memory Card must be inserted into a PC Card Adapter in order to be
used in a PC Card drive. We recommend the OMRON HMC-AP001 PC Card
Adapter.
PC Card
Adapter
28
SECTION 4
Connecting External Devices
This section describes how to connect external devices through a parallel interface (a parallel connector) or serial
interface (the RS-232C/RS-422 connector or Ethernet connector).
4-1
4-2
Connecting through the Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
4-1-1
Parallel Connection Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
4-1-2
Parallel Connector Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . .
32
4-1-3
I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Connecting through the Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4-2-1
RS-232C/RS-422 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4-2-2
Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
29
Section 4-1
Connecting through the Parallel Interface
4-1
Connecting through the Parallel Interface
This section explains how to connect I/O to the F250 through its parallel interface to input signals such as measurement triggers or output signals such as
measurement results.
When you want to use the parallel interface to input commands and output
measurement results, prepare a parallel I/O cable and connect it to the parallel
connector. A Terminal Block can also be used to connect external devices.
Refer to the F250 Vision Sensor Manual 2: Operation Manual for details on
communications settings and I/O formats.
4-1-1
Parallel Connection Methods
Using a Parallel I/O Cable
Use an F160-VP Parallel I/O Cable (sold separately) to connect the F250 to
external devices. Align the connectors and insert the cable’s connector
straight into the F250’s parallel connector. Tighten the connector’s mounting
screws to secure the connection.
Parallel
Connector 0
Parallel
Connector 1
Marks (1 to 4)
F160-VP Parallel
I/O Cable (2 m)
FG terminals
Ground to 100 W or less.
Precaution
30
1.
Wire color
Turn OFF the power supply before connecting or disconnecting a Parallel
I/O Cable. Peripheral devices may be damaged if the cable is connected
or disconnected ZLWKWKHSRZHU21
Connecting through the Parallel Interface
2.
Section 4-1
The parallel connectors are capped with screw-on covers when the F250
is shipped. When a connector is not being used, leave the cover in place
or replace the cover to protect against dust, dirt, and static electricity.
Using a Screw Terminal Block
Use a Screw Terminal Block and Special Cable to connect the F250 to external devices such as PLCs.
Parallel
Connector 0
Parallel
Connector 1
Special Cable
XW2Z-100B (1 m)
XW2Z-200B (2 m)
XW2Z-300B (3 m)
XW2Z-500B (5 m)
XW2B-40G5 Screw
Terminal Block
PLC or other device
31
Section 4-1
Connecting through the Parallel Interface
4-1-2
Parallel Connector Specifications
Parallel Connector 0
A20
A1
B20
B1
Each wire of the F160-VP Parallel I/O Cable
has a unique wire-color/mark combination.
Pin
Signal
Color
Mark
(Black)
A1
5(6(7
/WEURZQ
■
$
67(3
<HOORZ
■
A3
DI0
Green
■
Function
5HVWDUWVWKH
)
Pin
Signal
&20,1
/WEURZQ
■
0HDVXUHPHQW
WULJJHUVLJQDO
LQSXW
B
'6$
<HOORZ
■
Command
input
B3
DI1
Green
■
B4
DI3
Gray
■
White
■
A4
DI2
Gray
A5
DI4
White
■
B5
DI5
■■
B6
DI7
A7
DI6
(Open)
/WEURZQ
<HOORZ
Mark
(Red)
B1
■
A6
Color
■■
(Leave open.)
B7
(Open)
/WEURZQ
<HOORZ
Strobe trigger 0
output (See
note 1.)
B8
STGOUT1
ERROR
Function
Common for
input signals
(See note 2.)
,QSXWVGDWD
VHQGUHTXHVW
VLJQDOV
Command
input
■■
■■
(Leave open.)
Green
■■
Strobe trigger 1
output (See
note 1.)
Gray
■■
ON when there
is an error.
A8
STGOUT0 Green
■■
A9
RUN
Gray
■■
ON while in
Run mode
B9
A10 BUSY
White
■■
B10 GATE
White
■■
■■■
Combined
judgement
result
B11 COMOUT1
/WEURZQ
ON for the set
output time
A11 OR
/WEURZQ
ON during processing
■■■
Common for
control signals
(See note 3.)
Data output
Data output
$
DO0
<HOORZ
■■■
B DO1
<HOORZ
■■■
A13 DO2
Green
■■■
B13 DO3
Green
■■■
A14 DO4
Gray
■■■
B14 DO5
Gray
■■■
A15 DO6
White
■■■
B15 DO7
White
■■■
A16 DO8
/WEURZQ
■■■■
B16 COMOUT2
/WEURZQ
■■■■
A17 DO9
<HOORZ
■■■■
B17 DO10
<HOORZ
Common for
DO0 to DO7
■■■■
Data output
A18 DO11
Green
■■■■
B18 DO12
Green
■■■■
A19 DO13
Gray
■■■■
B19 DO14
Gray
■■■■
A20 DO15
White
■■■■
B20 COMOUT3 White
32
■■■■
Common for
DO8 to DO15
Precaution
Do not input the RESET input immediately after turning ON the power. When
using RESET input to synchronize startup timing, wait at least 1 s after turning
21WKH)
VSRZHUVXSSO\EHIRUHWXUQLQJ21WKH5(6(7VLJQDO
CHECK
Use a DC power supply with countermeasures against high voltages (safe
extra low-voltage circuits on the secondary side) for the COMIN and COMOUT
terminals. If the V\VWHPPXVWPHHW8/VWDQGDUGVXVHD8/FODVV,,SRZHUVXS
SO\
Section 4-1
Connecting through the Parallel Interface
Parallel Connector 1
A20
A1
B20
B1
Each wire of the F160-VP Parallel I/O Cable
has a unique wire-color/mark combination.
Pin
Signal
A1
(Open)
$
5HVHUYH
LQSXW
Color
Mark
(Black)
Function
Pin
/WEURZQ
■
(Leave open.)
B1
<HOORZ
■
(Leave open.)
B
Command
input
A3
DI8
Green
■
A4
DI10
Gray
■
A5
DI12
White
Color
■
5HVHUYH
LQSXW
<HOORZ
Common for
input signals
(See note 2.)
■
(Leave open.)
Command
input
B3
DI9
Green
■
B4
DI11
Gray
■
■
B5
DI13
White
■
■■
B6
DI15
(Leave open.)
B7
(Open)
■■
Strobe trigger 2
output
(See note 1.)
B8
STGOUT3
Gray
■■
(Leave open.)
B9
5HVHUYH
RXWSXW
A10
White
■■
(Leave open.)
B10 Reserve
output
A11
/WEURZQ
■■■
(Leave open.)
DO16
<HOORZ
■■■
Data output
A13 DO18
Green
■■■
A14 DO20
Gray
■■■
A15 DO22
White
■■■
A7
(Open)
A8
STGOUT2 Green
A9
5HVHUYH
RXWSXWV
$
Function
/WEURZQ
/WEURZQ
<HOORZ
DI14
Mark
(Red)
&20,1
■■
A6
/WEURZQ
<HOORZ
Signal
■■
■■
(Leave open.)
Green
■■
Strobe trigger 3
output
(See note 1.)
Gray
■■
(Leave open.)
White
■■
(Leave open.)
B11 COMOUT4
/WEURZQ
■■■
B DO17
<HOORZ
Common for
control signals
(See note 3.)
■■■
Data output
B13 DO19
Green
■■■
B14 DO21
Gray
■■■
B15 DO23
White
■■■
A16 DO24
/WEURZQ
■■■■
B16 COMOUT5
/WEURZQ
■■■■
Common for
DO16 to DO23
A17 DO25
<HOORZ
■■■■
B17 DO26
<HOORZ
■■■■
Data output
A18 DO27
Green
■■■■
B18 DO28
Green
■■■■
A19 DO29
Gray
■■■■
B19 DO30
Gray
■■■■
A20 DO31
White
■■■■
B20 COMOUT6 White
Note
1.
■■■■
Common for
DO24 to DO31
Refer to page 70 for details if you want to connect a strobe device to the
F250.
Each Camera has its own strobe trigger output as shown in the following
table.
33
Section 4-1
Connecting through the Parallel Interface
Camera
Strobe trigger output signal
Camera 0
STGOUT0 (Pin A8 of parallel connector 0)
Camera 1
STGOUT1 (Pin B8 of parallel connector 0)
Camera 2
STGOUT2 (Pin A8 of parallel connector 1)
Camera 3
STGOUT3 (Pin B8 of parallel connector 1)
2.
COMIN1 is the common for A1 to A6 and B2 to B6 on connector 0.
COMIN2 is the common for A3 to A6 and B3 to B6 on connector 1.
3.
COMOUT1 is the common for A8 to A11 and B8 to B10 on connector 0.
COMOUT4 is the common for A8 and B8 on connector 1.
Wiring Connector-Terminal Block Conversion Units
Connector-Terminal Block Conversion Unit
Manufacturer
OMRON
Model
XW2B-40G5
Connecting Cables
Manufacturer
OMRON
Model
XW2Z-100B (1 m)
XW2Z-200B (2 m)
XW2Z-300B (3 m)
XW2Z-500B (5 m)
34
Section 4-1
Connecting through the Parallel Interface
Connecting to the F250
Parallel
connector 0
Connecting to Parallel Connector 0
Parallel
connector 1
1
39
Conversion
Unit Terminal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Signal
RESET
STEP
DI0
DI2
DI4
DI6
Not used.
STGOUT0
RUN
BUSY
OR
DO0
DO2
DO4
DO6
DO8
DO9
DO11
DO13
DO15
Conversion
Unit Terminal
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal
COMIN1
DSA
DI1
DI3
DI5
DI7
Not used.
STGOUT1
ERROR
GATE
COMOUT1
DO1
DO3
DO5
DO7
COMOUT2
DO10
DO12
DO14
COMOUT3
Connecting to Parallel Connector 1
2
Connector-Terminal Block
Conversion Unit
SeeAlso
40
Conversion
Signal
Unit Terminal
1
Not used.
3
Reserve
input
5
DI8
7
DI10
9
DI12
11
DI14
13
Not used.
15
STGOUT2
17
Reserve
output
19
Reserve
output
21
Reserve
output
23
DO16
25
DO18
27
DO20
29
DO22
31
DO24
33
DO25
35
DO27
37
DO29
39
DO31
Conversion
Signal
Unit Terminal
2
COMIN2
4
Reserve
input
6
DI9
8
DI11
10
DI13
12
DI15
14
Not used.
16
STGOUT3
18
Reserve
output
20
Reserve
output
22
COMOUT4
24
26
28
30
32
34
36
38
40
DO17
DO19
DO21
DO23
COMOUT5
DO26
DO28
DO30
COMOUT6
Refer to the beginning of 3DUDOOHO &RQQHFWRU 6SHFLILFDWLRQV for signal
definitions.l
35
Section 4-1
Connecting through the Parallel Interface
Making a Parallel I/O Cable
A parallel I/O cable can be assembled using the following connector and cover
or equivalent components. Keep the cable length less than P
Component
CHECK
4-1-3
Manufacturer
Connector
Fujitsu
Cover
Fujitsu
Model number
)&1-$8
)&1&%
Double-check the connector wiring for mistakes before turning ON the power
VXSSO\IRUWKHILUVWWLPH
I/O Specifications
Input Specifications
Item
Specification
Model
F250-C50 (NPN mode)
Input voltage
12 to 24 VDC –10%
ON current
5 to 15 mA
ON voltage
8.8 V max.
F250-C55 (PNP mode)
OFF current
0.1 mA max.
OFF voltage
4.5 V min.
ON delay
RESET input: 10 ms max.
OFF delay
RESET input: 15 ms max.
Other inputs: 0.5 ms max.
Other inputs: 0.7 ms max.
Internal circuits
Input
terminal
COM IN
+
Input
terminal
COM IN
Output Specifications
Item
Specification
Model
F250-C50 (NPN mode)
Output voltage
12 to 24 VDC –10%
Load current
45 mA max.
ON residual voltage
2 V max.
OFF leakage current
0.1 mA max.
F250-C55 (PNP mode)
Internal circuits
Output terminal
Load
COM OUT
+
Load
COM OUT
Precaution
36
Output terminal
Do not exceed the maximum load current specified for the F250. The F250 will
be damaged if an output is short-circuited.
Section 4-2
Connecting through the Serial Interface
4-2
Connecting through the Serial Interface
The F250’s serial interface (RS-232C/RS-422 connector or Ethernet connector) can be used to input signals such as measurement triggers or output signals such as measurement results. Additionally, data that has been set in the
F250 can be backed up in a personal computer.
Refer to Section 6 Communicating with External Devices in the F250 Vision
Sensor Manual 2: Operation Manual for details on communications settings
and I/O formats.
4-2-1
RS-232C/RS-422 Connections
Connection Examples
1:1 Connection (Normal, Menu Operation)
RS-232C cable
F250
Computer
Multi-drop Connection (Normal)
Communications between one computer and several F250s is possible using
Link Adapters.
31 Units max.
RS-232C cable
Link Adapter
RS-422
cable
OMRON
3G2A9-AL004-E
recommended
Computer
RS-422 cable
Link Adapter
Link Adapter
OMRON
B500-AL001
recommended
RS-422 cable
F250
CHECK
Link Adapter
F250
F250
When 3G2A9-AL004-E Link Adapters are being used, termination must be set
to ON in the last node in the line and the node must be terminated as follows:
• Connect 220 W (1/2 W min.) between RDA(-) and RDB(+).
• Connect 220 W (1/2 W min.) between SDA(-) and SDB(+).
37
Section 4-2
Connecting through the Serial Interface
1:1 Connection (Host Link)
RS-232C cable
F250
PLC
Connector
The F250’s RS-232C/RS-422 Connector is a 9-pin D-SUB female connector.
The pin allocation is shown below.
2
1
6
3
7
4
8
5
9
Pin
1
Signal
Name
FG
Protective frame ground
2
SD
For RS-232C
3
RD
4
NC
Not connected
5
RDB(+)
For RS-422
6
RDA(-)
7
SDB(+)
8
SDA(-)
9
GND
Signal ground
The following plug and hood are recommended and are available from
OMRON.
Model
Model No.
Plug
XM2A-0901
Hood
XM2S-0911
Wiring
The maximum cable length is 15 m for RS-232C or RS-422
RS-232C Wiring
F250
External device
Signal
Pin
2
Pin
✽
Signal
SD
RD
3
✽
RD
GND
9
✽
GND
Use only shielded cable.
38
SD
RS/CS control
cannot be used.
Section 4-2
Connecting through the Serial Interface
RS-422 Wiring
F250
Signal
External device
Pin
Signal
RDB (+)
5
Pin
✽
RDB (+)
RDA (−)
6
✽
RDA (−)
SDB (+)
7
✽
SDB (+)
SDA (−)
8
✽
SDA (−)
GND
9
✽
GND
Use only shielded cable.
Note Pin numbers on the external device will depend on the device being connected. Refer to the manual for the personal computer or PLC being connected.
Connection
Align the connector with the socket and press the connector straight into
place. Tighten the two mounting screws to secure the connector.
Precaution
Always turn OFF the power supply before connecting or disconnecting cables.
The peripheral device may be damaged if connected or disconnected with the
power supply turned ON.
Note The connector is capped when the F250 is shipped. When not using the serial
interface, leave the cap in place to protect against dust, dirt, and static electricity.
39
Section 4-2
Connecting through the Serial Interface
4-2-2
Ethernet Connection
Connection Examples
■ 1:1 Connection
Use a Shielded (STP) 10 Base-T Crossover Cable to make the 1:1 connection.
The cable length must be less than 30 m.
10 Base-T Crossover Cable (STP)
(Less than 30 m)
F250
Computer
■ 1:N Connection
A Hub can be used to communicate with two or more F250s from a single
computer. Use Shielded (STP) 10 Base-T Straight-through Cables to make the
1:N connections. The cable length between the F250s and the Hub must be
less than 30 m.
Computer
10 Base-T Straightthrough Cable (STP)
HUB
10 Base-T
Straight-through
Cable (STP)
(Less than 30 m)
F250
40
10 Base-T
Straight-through
Cable (STP)
(Less than 30 m)
F250
10 Base-T
Straight-through
Cable (STP)
(Less than 30 m)
F250
Connecting through the Serial Interface
Section 4-2
Connection
Align the connector with the socket and press the connector straight into place.
Precaution
CHECK
1.
Always turn OFF the power supply before connecting or disconnecting cables. The peripheral device may be damaged if connected or disconnected
with the power supply turned ON.
2.
The Ethernet connector is capped when the F250 is shipped. When the
Ethernet interface isn’t being used, leave the cap in place or replace the
cap to protect against dust, dirt, and static electricity.
Refer to Section 6 Communicating with External Devices in the F250 Vision
Sensor Manual 2: Operation Manual for details on setting the F250’s IP
Address and Subnet Mask.
41
SECTION 5
Troubleshooting and Maintenance
This section provides tables to help identify and correct hardware errors that may occur with the F250 as well as
information on maintenance and periodic inspections.
5-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5-1-1
Connection Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5-1-2
Menu Operation Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5-1-3
Parallel Interface Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5-1-4
Serial Interface (RS-232C/RS-422) Errors. . . . . . . . . . . . . . . . . . . .
45
5-1-5
Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
5-1-6
Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
5-1-7
Serial Interface (Ethernet) Errors . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
5-1-8
Cabling Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
5-2-1
Replacing the Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
5-3
Regular Inspections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
5-4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
5-5
F200/F300 Camera Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
5-6
Connecting a Strobe Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
5-2
43
Section 5-1
Troubleshooting
5-1
Troubleshooting
This section lists probable corrections for common hardware problems. Please
check all of the following items before requesting repairs.
5-1-1
Connection Errors
Problem
The POWER indicator is not lit.
Probable cause
The Power Supply is not connected properly.
The supply voltage is not 24 VDC +10%/-15%.
The Video Monitor is blank.
The power to the Video Monitor is not ON.
The Monitor Cable is not connected properly.
The Video Monitor is malfunctioning.
When using an LCD Monitor, the power supply capacity is insufficient.
The Video Monitor image is not
clear.
There is electrical noise entering from the power supply or cables.
Cannot make key inputs from the
Console.
The Console Cable is not correctly connected.
Camera images do not appear on
the screen (for Cameras with Light
Source).
The Camera Cable is not correctly connected.
Camera images do not appear on
the screen (when a standard CCTV
lens and lighting are used).
The lens cap has not been removed.
The Monitor Cable is not correctly connected.
The lighting cable is not properly connected to the Camera.
The Camera Cable is not properly connected.
The lens iris is opened or closed too far.
The shutter speed is not suitable.
The lighting method is not suitable.
The indicators do not turn ON (for
Cameras with Light Source).
The lighting cable is not correctly connected to the Camera.
Power is not being supplied to the F250.
When using a Camera with Intelligent Lighting, the DIP switch pins are not
set to 0.
5-1-2
Menu Operation Errors
Problem
The measurement results are not
displayed on the Video Monitor.
5-1-3
Probable cause
The F250 is not in Monitor or Run mode.
Parallel Interface Errors
Problem
Trigger signals (input signals) are
not received.
Probable cause
The cables are not correctly wired.
The signal line is disconnected.
The status of communications can be checked with the I/O monitor.
The F250 is not in Monitor or Run mode.
Signals cannot be output externally. The trigger signal has not been input.
The cables are not correctly wired.
The signal line is disconnected.
The status of communications can be checked with the I/O monitor.
The F250 is not in Run mode.
44
Section 5-1
Troubleshooting
5-1-4
Serial Interface (RS-232C/RS-422) Errors
Problem
No communications are possible.
Probable cause
The cables are not correctly wired.
The F250’s communications specifications do not match those of the
external device.
The communications mode was not selected under System settings/
Communication/Serial.
Select Normal, Host link, or Menu in the Communications (Serial)
menu. (Normal is no-protocol.)
The status of communications can be checked with the I/O monitor.
The Unit operates well initially, but
after a while there is no response
from the F250.
The reception buffer on the external device (e.g., computer) is full. Check
that settings allow the data to be properly received.
Cannot perform menu operations
from the computer.
The communications mode was not set to Menu in the System settings/
Communication/Serial settings.
Data cannot be saved
•
•
5-1-5
Are the same communications conditions set for both the external
device and the F250?
Is flow control turned OFF under System settings/communication/
Normal? Refer to the F250 Operation Manual.
Cameras
Problem
Are the shutter trigger pulses synchronized when more than one
camera is connected?
Probable cause
The shutter trigger pulses are not synchronized for the F160-S1 and
F150-S1. The timing is offset so that light from other Cameras does not
enter. The offset depends on the model of Camera that is used.
Model
F160-S1
tD
Approx. 500 m s Approx. 1 ms
F150-S1
If a strobe is used, the strobe trigger
signals are also offset in the same way as
the shutter trigger pulses.
Camera 0
Camera 1
Camera 2
Camera 3
tD
Shutter trigger pulses ON
The shutter trigger pulses are synchronized for other Cameras, i.e., there
is no offset.
Can more than one internally synchronized Cameras be connected?
No. Only one F200-S Camera (internal sync) can be connected, and it
must be connected to Camera connector 0.
Can the F150-LT10A Light be connected to the F160-S1 Camera?
Yes, it can be connected and the following Lenses are available.
5-1-6
•
•
Lens with 20-mm field of vision: F150-LE20
Lens with 50-mm field of vision: F150-LE50
Memory Cards
Problem
Can either of the Memory Card
slots be used?
Probable cause
Only the following two functions have restrictions in the slot that can be
used.
• Starting the Setup Menu: Slot 0 only
• Switching scene groups: Slot 1 only
Either slot can be used for all other functions (outputting results to a Memory Card, saving scene data, etc.).
45
Section 5-2
Maintenance
5-1-7
Serial Interface (Ethernet) Errors
Problem
Probable cause
No communications are possible.
A 10 Base-T Crossover Cable is not being used for a 1:1 connection.
10 Base-T Straight-through Cables are not being used for the 1:N connections.
Power is not being supplied to the HUB, the settings are incorrect, or the
connections are incorrect.
The personal computer’s IP Address and Subnet Mask settings are not
correct or the settings are duplicated in another device.
The F250’s IP Address and Subnet Mask settings are not correct or the
settings are duplicated in another device.
The IP Address set for the F250 in the computer’s communications software is incorrect.
The communications mode was set to Normal or Menu in the System
settings/Communication/Serial window.
The status of communications can be checked with the I/O monitor.
The F250 is being accessed by another computer.
Communications are being affected by a noise source (such as a power
line) that is too close to the F250 or communications cables.
Communications are not set for a TELNET connection (TCP/IP, port 23) in
the computer’s communications software.
The Unit operates well initially, but
after a while there is no response
from the F250.
The reception buffer on the external device (e.g., computer) is full. Check
that settings allow the data to be properly received.
The response from the F250 is
slow.
(It takes too long to transfer data
and errors occur.)
The IP Address of the F250 or computer is duplicated in another device.
Communications are being affected by a noise source (such as a power
line) that is too close to the F250 or communications cables.
The network’s communications load is too heavy.
The computer’s processing load is too heavy. (A program that requires a
lot of processing capacity is being run simultaneously.)
Cannot perform menu operations
from the computer.
5-1-8
The communications mode was not set to Menu in the System settings/
Communication/Serial settings.
Cabling Errors
Problem
Probable cause
A recommended OMRON RS-232C
cable is not being used.
One of the following OMRON cables can be used. Select a cable that
works with the device being connected.
Connecting to a PC/AT or compatible computer (9-pin connector)
• XW2Z-200S-V (2 m)
• XW2Z-500S-V (5 m)
Connecting to a SYSMAC device (9-pin connector)
•
•
Can a commercially available cable
be used instead of the R150-VM
Monitor Cable?
5-2
5-2-1
XW2Z-200T (2 m)
XW2Z-500T (5 m)
Yes, as long as it’s a pin jack cable (with a yellow connector) for video
signal connection.
Maintenance
Replacing the Light
• The Light will gradually lose brightness over time (about 20% loss after
1,500 hours of use). Replace the Light after about 1,500 hours of use.
46
Section 5-2
Maintenance
• Replace the Light if it is damaged or not fully functional.
F150-SL20A/SL50A
Use the following procedure to replace a Light with the F150-LT10A Light.
(The F150-LT10A cannot be connected to the older F150-S1 Camera.)
Removing the Light
Camera base
2
3
1
Hold this part when
removing the Cable.
4
Light
Lighting connector
Camera cable
connector
1.
Disconnect the light cable from the light connector on the back of the Camera.
2.
Remove the light cable from the slot in the camera base.
3.
Remove the two screws securing the Light.
4.
Remove the Light from the Camera.
Precaution
Do not disassemble the Lens. Disassembly can damage the Lens.
Installing the Light
Camera base
3
2
4
1
Light
Lighting connector
Camera cable
connector
1.
Mount the Light on the Camera.
2.
Screw in the two screws that secure the Light.
3.
Place the light cable in the slot in the camera base.
4.
Connect the light cable to the light connector on the back of the Camera.
47
Section 5-2
Maintenance
F150-SLC20/SLC50 or F160-SLC20/SLC50
Use the following procedure to replace a Light with an F150-LTC20 (20-mm
field of vision) or F150-LTC50 (50-mm field of vision) Light.
Removing the Light
5
3
Camera base
2
Light
4
1
Hold this part when
removing the Cable.
1.
Disconnect the light cable from the light connector on the back of the Camera.
2.
Remove the light cable from the slot in the camera base.
3.
Remove the two screws securing the Light at the top.
4.
Remove the two screws securing the Light at the bottom.
5.
Remove the Light from the Camera.
Precaution
Do not disassemble the Lens. Disassembly can damage the Lens.
CHECK
When you want to use the Camera alone without connecting an Intelligent
Lighting, use M2 ™ 3 screws in the bottom of the Camera instead of the
long screws removed in step 4. The screws removed in step 3 are not
needed.
Installing the Light
3
1
Camera base
4
Light
2
5
48
1.
Mount the Light on the Camera.
2.
Screw in the two screws that secure the Light at the bottom.
3.
Screw in the two screws that secure the Light at the top.
Section 5-3
Regular Inspections
5-3
4.
Place the light cable in the slot in the camera base.
5.
Connect the light cable to the light connector on the back of the Camera.
Regular Inspections
To maintain the F250 in the best condition, perform the following regularly.
• Clean the Lens and LED indicators with a lens-cleaning wipe or blow off
dust with an aerosol air sprayer.
• Lightly wipe off dirt with a soft cloth.
Inspection point
Details
Tools required
Power supply
The voltage measured at the power supply
terminals must be 24 VDC +10%/-15%.
Circuit tester
Ambient temperature
The operating ambient temperature inside
the cabinet must be between 0 and 50•C.
Thermometer
Ambient humidity
The operating ambient humidity inside the
cabinet must be between 35% and 85%.
Hygrometer
Installation
Each component must be firmly secured.
Phillips screwdriver
Each cable connector must be correctly
inserted and locked.
The Cameras must be firmly secured.
The camera lens mounts must be firmly
secured.
Indicators
All indicators must light when the power is
turned ON.
---
Verify that a through-image is displayed.
When using an Intelligent Lighting, verify
that the light level settings are set to their
maximum values.
Precaution
• Turn OFF the power and take safety precautions before conducting
inspections. Electrical shock can result from attempting safety inspections
with the power turned ON.
• Do not use thinners or benzene to clean the F250. They will damage
F250 components.
49
Section 5-4
Specifications
5-4
Specifications
This section provides the specifications and dimensions of the F250 and its
peripheral devices. (All dimensions are in mm unless otherwise noted.)
F250-C50/C55 Vision Mate Controller
115 min.
8
73
270
197
220–0.6
(25)
Four M4 taps
(for mounting)
This screw hole
cannot be used.
136 0.5
Stopper
–
10 to 13
Panel thickness:
T
Item
Screw length L:
10+T < L < 13+T
(14)
190–0.6
(40)
Specification
Model
F250-C50
F250-C55
Input/Output type
NPN
PNP
Supply voltage
20.4 to 26.4 VDC
Current consumption 3.0 A max.
Insulation resistance
20 MW min. between all DC external terminals and GR terminal (100 VDC Megger, with
internal surge absorber removed)
Dielectric strength
1,000 VAC, 50/60 Hz between all DC external terminals and GR terminal (with internal
surge absorber removed)
Leakage current
10 mA max.
Noise resistance
2,000 V; pulse width: 50 ns; rise time: 5 ns (pulse)
Burst continuation time: 15 ms; Period: 300 ms
Vibration resistance
10 to 150 Hz; half-amplitude: 0.1 mm; maximum acceleration: 15 m/s2, 10 times for 8
minutes each in 3 directions.
Shock resistance
150 m/s2, 3 times each in 6 directions
Ambient temperature Operating: 0 to 50•C (with no condensation)
Storage: -25 to 65•C (with no condensation)
Ambient humidity
Operating and storage: 35% to 85% (with no condensation)
Ambient environment No corrosive gases
Ground
Class 1 (Ground resistance 100 W max.)
Degree of protection
IEC60529 IP20 (in-panel)
Case material
SECC-T
50
Section 5-4
Specifications
Item
Specification
Battery life
Approximately 7 years when used 24 hours/day.
Weight
Approx. 3.1 kg (Controller only)
F150 Cameras
Cameras with Light
■ F150-SL20A/SL50A
(70.5)
67
39
Unit: mm
1
25.4
3.8 dia.
43
27
F150-LT10A Light
(50.25)
(16.75)
Two M4 taps, Depth 8
1/4-20UNC tap, Depth 8
(40.25)
20±0.1
(6.75)
51
Section 5-4
Specifications
Cameras with Intelligent Lighting
■ F150-SLC20
F150-LTC20 Light
Unit: mm
70
2.5
12
73
12
(85)
40
25
2.5
42.5
4 dia.
70
(10)
12
12
30.5
31
40
(96.25)
(16.75)
Two M4 taps, Depth 10
1/4-20UNC tap,Depth 10
(86.25)
52
20±0.3
(6.75)
Section 5-4
Specifications
■ F150-SLC50
F150-LTC50 Light
Unit: mm
90
80
2.5
16
16
(85)
40
25
2.5
52.5
4 dia.
90
(10)
16
16
30.5
31
60
(103.25)
(16.75)
Two M4 taps, Depth 10
1/4-20UNC tap, Depth 10
(93.25)
20±0.3
(6.75)
53
Section 5-4
Specifications
Camera Only
■ F150-S1A
Unit: mm
48
(15.5)
8
(6)
(40)
(6.2)
(6.2)
1"-32UN-2A
(C mount)
30.5
31.25±2
11
(21.7)
(30.7)
29
(14.5)
Light Connector
(8.8 dia.)
1.5
31
(16.75)
Two M4 taps, Depth 8
1/4-20UNC tap, Depth 8
21.25±2
54
20±0.1
(6.75)
Camera Cable
Connector
(11.8 dia.)
Section 5-4
Specifications
F160 Cameras
Cameras with Intelligent Lighting
■ F160-SLC20
F150-LTC20 Light
Unit: mm
70
2.5
12
73
12
(85)
46.5
25
2.5
42.5
4 dia.
70
(10)
12
12
30.5
31
8
40
(96.25)
(23.25)
1/4-20UNC tap, Depth 10
Two M4 taps, Depth 10
(86.25)
20±0.3
(13.25)
55
Section 5-4
Specifications
■ F160-SLC50
F150-LTC50 Light
Unit: mm
90
80
2.5
16
16
(85)
46.5
25
2.5
52.5
4 dia.
90
(10)
16
16
30.5
8
31
60
(23.25)
(103.25)
1/4-20UNC tap, Depth 10
Two M4 taps, Depth 10
(93.25)
20±0.3
(13.25)
Camera Only
■ F160-S1
Unit: mm
54.5
(15.5)
8
(6)
(46.5)
(6.2)
(6.2)
1"-32UN-2A
(C mount)
30.5
31.25±2
8
11
(21.7)
(30.7)
29
(14.5)
Light Connector
(8.8 dia.)
31
(23.25)
21.25±2
Two M4 taps, Depth 8
1/4-20UNC tap, Depth 8
20±0.1
(13.25)
56
Camera Cable
Connector
(11.8 dia.)
Section 5-4
Specifications
Camera Specifications
General Specifications
Item
Specification
Supply voltage
F150-series: 12 VDC
F160-series: 13 VDC
Current consumption
F150-S1A: 100 mA max.
F150-SL20A/SL50A: 110 mA max.
F150-SLC20/SLC50: 200 mA max.
F160-S1: 130 mA max.
F160-SLC20: 260 mA max.
F160-SLC50: 310 mA max.
Vibration resistance
10 to 150 Hz; half-amplitude: 0.35 mm; maximum acceleration: 50 m/s2, 10 times for 8
minutes each in 3 directions
Shock resistance
150 m/s2, 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
Operating and storage: 35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Camera materials
Cover: Galvanized steel sheet metal
Case: Die-cast aluminum alloy
Camera mounting base: Fiber-reinforced plastic (black)
Light materials
(Cameras with Lights)
Case: ABS
Transparent cover: PC
Weight
F150-S1A: Approx. 80 g
F150-SL20A/SL50A: Approx. 135 g
F150-SLC20: Approx. 280 g
F150-SLC50: Approx. 370 g
F160-S1: Approx. 85 g
F160-SLC20: Approx. 285 g
F160-SLC50: Approx. 375 g
Characteristics
■ Camera Characteristics
Item
Specification
Picture element
1/3" Interline CCD (reading all pixels)
Effective pixels
659 ™ 494 (H ™ V)
Synchronization
External sync. via horizontal sync signal
Shutter speed
F150-series: 1/100 s, 1/500 s, 1/2000 s, 1/10000 s
(Electronic shutter)
F160-series: 1/120 s, 1/200 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 1/8000 s,
1/20000 s
Lens mounting
C mount
■ Lens Characteristics (Cameras with Lights only)
Item
Specification
Lens model
F150-SL20A: F150-LE20
F150-SL50A:F150-LE50
F150-SLC20:F150-LE20
F150-SLC50:F150-LE50
F160-SLC20:F150-LE20
F160-SLC50:F150-LE50
Method
Fixed focal point, fixed iris
57
Section 5-4
Specifications
Item
Specification
Brightness
F2.8
Focal point distance
F150-SL20A: 13 mm
F150-SL50A: 6.1 mm
F150-SLC20:13 mm
F150-SLC50: 6.1 mm
F160-SLC20:13 mm
F160-SLC50: 6.1 mm
■ Light Characteristics (Cameras with Lights only)
Item
Specification
Light model
F150-SL20A/SL50A: F150-LT10A
F150-SLC20:F150-LTC20
F150-SLC50:F150-LTC50
F160-SLC20:F150-LTC20
F160-SLC50:F150-LTC50
Light source
F150-SL20A/SL50A:
Red LED (Peak emission wavelength: 680 nm)
F150-SLC20/SLC50 and F160-SLC20/SLC50:
Red and green LED combination
(Peak emission wavelengths: 660 nm and 570 nm)
Light emission method Pulse emission (synchronized with the camera shutter)
■ Other Characteristics
Item
Specification
Mounting distance
F150-S1A: Depends on lens being used.
F150-SL20A: 61 to 71 mm
F150-SL50A: 66 to 76 mm
F150-SLC20: 15 to 25 mm
F150-SLC50: 16.5 to 26.5 mm
F160-S1: Depends on lens being used.
F160-SLC20: 15 to 25 mm
F160-SLC50: 16.5 to 26.5 mm
Field of vision
F150-S1A: Depends on lens being used.
F150-SL20A: 20 mm ™ 20 mm
F150-SL50A: 50 mm ™ 50 mm
F150-SLC20: 20 mm ™ 20 mm
F150-SLC50: 50 mm ™ 50 mm
F160-S1: Depends on lens being used.
F160-SLC20: 20 mm ™ 20 mm
F160-SLC50: 50 mm ™ 50 mm
58
Section 5-4
Specifications
Consoles
■ F150-KP Console
Unit: mm
50
13
ENT
TRIG
SHIFT
CONSOLE
2000
Item
23
5
10
12.5
40
34
4.8 dia.
12 dia.
87
ESC
1.5
Specification
Vibration resistance
10 to 150 Hz; half-amplitude: 0.15 mm; 4 times for 8 minutes each in 3 directions
Shock resistance
196 m/s2; 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Degree of protection
IEC60529 IP20 (in-panel)
Minimum bending
radius
75 mm
Materials
Body: ABS
Cable sheathing: Heat-resistant chlorinated vinyl
Connector: PC and PBT
Weight
Approx. 135 g
59
Section 5-4
Specifications
■ F160-KP Console
29.7
48
Unit: mm
20
SHIFT
ENT
ESC
TRIG
F1
F3
F2
135.5
F4
F6
F5
F7
F9
F8
40
34
2000
4.8 dia.
12 dia.
Item
Specification
Current consumption
Approx. 10 mA
Vibration resistance
10 to 150 Hz; half-amplitude: 0.35 mm; maximum acceleration: 50 m/s2,10 times for 8
minutes each in 3 directions
Shock resistance
150 m/s2; 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Degree of protection
IEC60529 IP20 (in-panel)
Minimum bending
radius
75 mm
Materials
Body: ABS
Cable sheathing: Heat-resistant chlorinated vinyl
Connector: PC and PBT
Weight
Approx. 160 g
60
Section 5-4
Specifications
CHECK
The switch on the back of the F160-KP must be set to “ENABLE”.
SHIFT
ENT
ESC
TRIG
F1
F3
F2
F4
F6
F5
F7
F9
F8
ENABLE
ENABLE
These keys will be disabled if
the switch is set to "DISABLE".
DISABLEE
Cables
Camera Cables
■ Camera Cable Specifications
The F150-VS, F160-VSR3, and F160-VSR4 Camera Cables have different
dimensions and wiring, but they share the same specifications.
Item
Specification
Vibration resistance
10 to 150 Hz; half-amplitude: 0.15 mm, 4 times for 8 minutes each in 3 directions
Shock resistance
196 m/s2, 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Materials
Cable sheathing: Heat-resistant chlorinated vinyl
Connector: Fiberglass-reinforced PC and PBT
Minimum bending
radius
75 mm
Weight
Approx. 170 g
61
Section 5-4
Specifications
■ F150-VS Camera Cable (For [email protected], [email protected] Cameras)
3000
Unit: mm
43
F250 Connector
Signal
Camera Connector
Pin
Pin
Signal
Power
1
1
GND
GND
2
2
Power
GND
3
3
GND
VIDEO GND
4
4
VIDEO
VD
5
5
VIDEO GND
ESCNT1
6
6
HD
VIDEO
7
7
Not used.
HD
8
8
ESCNT1
SCAN
9
9
ESCNT2
ESCNT2
10
10
INDEX
INDEX
11
11
TRG
TRG
12
12
SCAN
Shell
Connector model:
Hirose RP17A-13PA-12PC
62
14.7 dia.
6 dia.
15 dia.
36
(30)
20 dia.
51
Shell
Connector model:
Hirose HR10A-10P-12S
Section 5-4
Specifications
■ F160-VSR3 Camera Cable (For F300-S2R/S3DR/S4R and [email protected]
Cameras)
Unit: mm
3000
(120)
43
F250 Connector
Signal
14.7 dia.
15 dia.
5.3 dia.
46
Camera Connector
Pin
Pin
Signal
Power
1
1
GND
GND
2
2
Power
GND
3
3
VIDEO GND
VIDEO GND
4
4
VIDEO
VD
5
5
HD GND
ESCNT1
6
6
HD
VIDEO
7
7
VD
HD
8
8
GND
SCAN
9
9
−
ESCNT2
10
10
INDEX(SI)
INDEX
11
11
TRG
TRG
12
12
VD GND
Shell
Connector model:
Hirose RP17A-13P-12PC
Shell
Connector model:
Hirose HR10A-10P-12S
63
Section 5-4
Specifications
■ F160-VSR4 Camera Cable (For F300-S Cameras)
Unit: mm
3000
43
14.7 dia.
15 dia.
46
5.3 dia.
17.4 dia.
(120)
Camera Connector
F250 Connector
Signal
Pin
Pin
Signal
Power
1
1
GND
GND
2
2
Power
GND
3
3
VIDEO GND
VIDEO GND
4
4
VIDEO
VD
5
5
HD GND
ESCNT1
6
6
HD
VIDEO
7
7
VD
HD
8
8
GND
SCAN
9
9
−
ESCNT2
10
10
INDEX(SI)
INDEX
11
11
Power
TRG
12
12
VD GND
Shell
Shell
Connector model:
Hirose RP17A-13P-12PC
Connector model:
Hirose HR10A-10P-12S
F150-VM Monitor Cable
Unit: mm
2000
46.7
3.3 dia.
11.5 dia.
46.7
Item
Specification
Vibration resistance
10 to 150 Hz; half-amplitude: 0.15 mm, 4 times for 8 minutes each in 3 directions
Shock resistance
196 m/s2, 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Materials
Cable sheathing: Heat-resistant chlorinated vinyl
Connector: PVC
64
Section 5-4
Specifications
Item
Specification
Minimum bending
radius
50 mm
Weight
Approx. 40 g
Accessories
BNC Jack Adapter
F160-VP Parallel I/O Cable
Unit: mm
40
40
20
200
20
11.6 dia.
40
200
2000
50
200
Item
Specification
Vibration resistance
10 to 150 Hz; half-amplitude: 0.15 mm, 4 times for 8 minutes each in 3 directions
Shock resistance
196 m/s2, 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Materials
Cable sheathing: Heat-resistant PVC
Connector: Polyester resin
Minimum bending
radius
120 mm
Weight
Approx. 340 g
65
Section 5-4
Specifications
F150-M05L LCD Color Monitor
Unit: mm
Mounting plate thickness: 1.6 to 4.8
(46 max.)
(155)
50 min.
SYNC
132
143
POWER
(145)
Mounting bracket
(100)
(5.5)
185
42.2
F150-VM Monitor Cable
• Tolerance: ±1 mm
174
The dimensions in parentheses
are provided for reference.
Panel opening dimensions
133.5
+0.5 mm
0
mm
175.5+0.5
0
Item
Specification
Supply voltage
20.4 to 26.4 VDC
Current consumption
700 mA max.
Vibration resistance
10 to 150 Hz; half-amplitude: 0.1 mm; maximum acceleration: 15 m/s2, 10 times for 8
minutes each in 3 directions
Shock resistance
150 m/s2, 3 times each in 6 directions
Ambient temperature
Operating: 0 to 50 •C (with no condensation)
Storage: -25 to 65 •C (with no condensation)
Ambient humidity
35% to 85% (with no condensation)
Ambient environment
No corrosive gases
Degree of protection
IEC60529 IP20 (in-panel)
Materials
Case: ABS/PC
Display surface: PMMA (Acrylic)
Panel size
5.5 inches (111.36 ™ 83.52 mm (H ™ V))
Panel type
TFT color liquid crystal
Resolution
320 ™ 240 dots
Image pitch
0.348 ™ 0.348 mm (H ™ V)
Contrast
85:1 (typical)
Viewable angle
25• up/down and 50• left/right (with a contrast ratio > 10)
Luminance
250 cd/m2 (typical)
Backlight
Cold cathode fluorescent light
Response speed
60 ms max.
Input signal
NTSC composite video (1.0 V/75 W termination)
66
Section 5-4
Specifications
Item
Specification
Weight
Approx. 1 kg
Accessories
Four mounting brackets
F150-M09 Video Monitor
Unit: mm
250
5
143
233
222
50
190
160
22
Item
Specification
Supply voltage
85 to 264 VAC, 50/60 Hz
Current consumption
20 W max.
Vibration resistance
5 to 100 Hz; 0.16-mm full-amplitude or acceleration of 7.35 m/s2 (whichever is smaller),
6 times for 10 minutes each in 3 directions
Ambient temperature
Operating: -10 to 50 •C (with no condensation)
Storage: -20 to 65 •C (with no condensation)
Ambient humidity
10% to 90% (with no condensation)
Ambient environment
No corrosive gases
Materials
Front: ABS plastic
Metal part: SECC (galvanized steel sheet)
CRT size
9 inch (164 ™ 123 mm (H ™ V))
CRT type
Monochrome CRT
Resolution
800 TV lines min. (at center)
System
Number of scanning lines: 600
Horizontal frequency:
15.75 kHz
Field frequency:
60 Hz
I/O impedance
75 W, high impedance (selectable)
I/O level and polarity
Composite image signal: 1 V (peak to peak)
Image:
0.7 V (peak to peak), positive
Synchronization:
0.3 V (peak to peak), negative
Input signal
NTSC composite video (1.0 V/75 W termination)
Weight
Approx. 4.5 kg
67
Section 5-5
F200/F300 Camera Parameters
Memory Cards
F160-N64S
42.8
Unit: mm
36.4
3.3
Item
Ambient temperature
Specification
Operating: 0 to 60 •C (with no condensation)
Storage: -25 to 85 •C (with no condensation)
Ambient humidity
8% to 95% (with no condensation)
Ambient environment
No corrosive gases
Life expectancy
300,000 overwrite operations
Number of pins
50 pins
Weight
Approx. 15 g
Application Software
F250-UME
42.8
Units: mm
36.4
3.3
Item
Ambient temperature
Specification
Operating: 0 to 60 •C (with no condensation)
Storage: -25 to 85 •C (with no condensation)
Ambient humidity
8% to 95% (with no condensation)
Ambient environment
No corrosive gases
Life expectancy
300,000 overwrite operations
Number of pins
50 pins
Weight
Approx. 15 g
5-5
F200/F300 Camera Parameters
Detailed parameter settings are required when a Camera other than an F150S1A or F160-S1 is connected. Make the following settings when using an
F200/F300 Camera. The Camera settings window is displayed at startup and
68
Section 5-5
F200/F300 Camera Parameters
can be displayed at other times by selecting Camera settings from the System Menu.
Camera settings
Camera settings(Detail)
Camera
: Others
Intelligent Lighting 0:
Out of use
Intelligent Lighting 1:
Out of use
Intelligent Lighting 2:
Out of use
Intelligent Lighting 3:
Out of use
End
Camera
Camera
speed
Shutter
Set the Camera model
to "Others" and select
"End".
End
Strobe
disable
Synchronization
Start
End
OFF
Internal
F300S
Standard
OFF
Exter- 6
nal
F300S2R
Standard
SYNC
Exter- -8
nal
-2
-2
0
1/4,000
0
1/10,000
-8
1/1,000
1/2,000
F300- StanS3DR dard
-2
Exter- -10
SYNC
nal
NON
RESET
F300S4R
Standard
NON
RESET
Note
(None)
60
20
(Note
2)
Positive
OFF
---
8
(None)
90
25
(Note
2)
Positive
OFF
---
-6
1/1,000
90
25
7
1/2,000
Nega- OFF
tive
---
0
90
25
7
Nega- OFF
tive
---
90
25
7
Nega- OFF
tive
---
-2
0
5
1/4,000
5
7
1/10,000
-14
-9
1/1,000
-8
-6
-6
-4
1/2,000
-5
-3
-3
-1
1/4,000
-3
-2
-1
1/8,000
0
1/10,000
0
1/30,000
0
1/50,000
-2
-2
Shutter
Exter- Image
read Y
trigger pulse
nal
timing
VD
3
Width Width Polar3
Sync
ity
17
3
Exter- -16
nal
-11
SYNC
Clamp pulse
Timing
Standard
RESET
10
Shutter
speed1
F200S
NON
Camera Speed :
Normal
: SYNC RESET
Shutter
Synchronization :
External
Strobe disable, start : [ 0]H
Strobe disable, end : [ 0]H
Clamp pulse timing : [ 90]CLK
Clamp pulse width : [ 25]CLK
Shutter trigger width : [ 3]H
1/1,500
1/3,000
1/6,000
1.
The shutter speed is set in the Camera itself.
2.
Set the shutter trigger pulse width to match the strobe’s specifications only
when a strobe is being used.
3.
These settings (indicated by ---) are ignored.
69
Section 5-6
Connecting a Strobe Device
5-6
Connecting a Strobe Device
Use the camera’s corresponding strobe trigger output signal (STGOUT0 to
STGOUT3) to control the strobe flash timing.
SeeAlso
Refer to page 32 for details on the pins allocated to these signals.
Check the strobe device's specifications and set the appropriate “Shutter trigger polarity” and “Shutter trigger width” in the Camera settings (Detail) Menu.
The Camera settings (Detail) window is displayed at startup and can be displayed at other times by selecting Camera settings from the System Menu.
Strobe specifications
When the flash is synchronized to the OFFto-ON transition of the strobe trigger signal
Shutter trigger
polarity
Positive
The “shutter trigger width” setting determines the pulse width W.
When using a Double-speed Camera:
W = Shutter trigger width setting (H) ™ 32 m s
(1H = 32 m s)
W
OFF
STGOUT0 to 3
Shutter trigger width
ON
When the flash is synchronized to the ON-to- Negative
OFF transition of the strobe trigger signal
When using a Camera other than a Doublespeed Camera:
W = Shutter trigger width setting (H) ™ 63 m s
(1H = 63 m s)
Note: Depending upon the timing, W may
have an error of up to –1H.
W
OFF
STGOUT0 to 3
ON
Combining an OMRON Camera and Strobe
The following table shows the timing polarity. Use a strobe that is compatible
with this timing.
Camera
Shutter trigger polarity
Shutter trigger width
F150-S1A
Positive
3H (1H = 63 m s)
F160-S1
Positive
3H (1H = 32 m s)
F200-S
Positive
Can be set to match the
strobe's specifications.
Negative
7H (1H = 63 m s)
F300-S
F300-S2R
F300-S3DR
F300-S4R
Note The window used to change the shutter trigger polarity and shutter trigger
pulse will not be displayed when an F150-S1A or F160-S1 Camera is connected, but the STGOUT0 to STGOUT3 signals will be output with the polarity
and width shown in the table above.
70
Index
A
ambient temperature, 3
F
F150 Cameras
dimensions, 51
B
battery
BATTERY LOW message, 5
replacing, 5
C
F150-KP, 59
F150-M05L, 66
F150-M09, 67
F150-S1A, 54
F150-SL20A/SL50A, 47, 51
F150-SLC20, 52
F150-SLC20/SLC50, 48
cables, 4
F150-SLC50, 53
Camera Cable specifications, 61
F150-VS, 62
Camera Only, 18
F160 Cameras
Camera with Intelligent Lighting, 18
dimensions, 55
Camera with Light, 18
F160-KP, 60
Cameras, 4
F160-N64S, 68
characteristics, 57
F160-S1, 56
connecting, 17
F160-SLC20, 55
overview, 17
F160-SLC20/SLC50, 48
parameters, 68
specifications, 57
CCTV lenses, 22
communications
connector, 38
wiring, 38
components, 4
F160-SLC50, 56
F160-VP, 65
F160-VSR3, 63
F160-VSR4, 64
F250-C50/C55, 50
field of vision, 58
installation, 4
G
names and functions, 14
computers
using Memory Cards, 28
ground, 19
connector, 38
I
Consoles
connecting, 17
I/O specifications, 36
specifications and dimensions, 59
inspections, 49
crimp terminals, 19
installation
components, 4
D
precautions, 2
site, 2
dimensions, 50
E
Ethernet, 40
Extension Tubes, 24
external devices
connecting, 29
L
LCD Monitor, 66
lenses, 22
characteristics, 57
diameters, 23
light
71
Index
characteristics, 58
replacing, 46
lighting, 25
M
R
RESET signal
precaution, 5
RS-232C, 38
RS-422, 38
maintenance, 46
manuals, ix
Memory Cards, 27
in personal computers, 28
removing, 4
specifications, 68
Monitor
specifications, 66
Monitors
connecting, 17
mounting, 15
distance, 58
N
S
Screw Terminal Blocks, 31
serial interface
connecting external devices, 37
signal lines, 4
specifications, 50
general, 50
I/O, 36
Parallel Connectors, 32
strobe
combining with Camera, 70
connecting, 70
system configuration, 12
noise resistance, 4
T
O
optical chart, 22
orientation, 2
temperature
ambient, 3
troubleshooting, 44
cables, 46
P
package contents
confirming, 6
connection errors, 44
menus, 44
parallel interface, 44
serial interface, 45
parallel interface
connecting external devices, 30
peripheral devices
connecting, 17
V
Video Monitor, 4, 67
power supply, 19
turning OFF, 5
wiring, 20
precautions, xi
applications, xii
battery, xii
general safety, xii
installation, 2
installation environment, xii
power supply and wiring, xii
products
availability, 6
72
W
wiring
communications, 38
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. SCHB-736A
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers
refer to the previous version.
Revision code
A
Date
September 2001
Revised content
Original production
73
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement