ALI-BC1720 Series HD-TVI Bullet Cameras Quick Installation Guide

ALI-BC1720 Series HD-TVI Bullet Cameras Quick Installation Guide
ALI-BC1720 Series HD-TVI Bullet
Cameras Quick Installation Guide
For Products: ALI-BC1720E, ALI-BC1720G
What’s in the box
•
•
•
•
Camera assembly
Mounting hardware
This instruction guide
Drill template
The ALIBI ALI-BC1720 series indoor/outdoor bullet cameras include a high sensitivity sensor with advanced
circuit design technology. They feature high resolution, low image distortion and low noise features which
makes them suitable for both surveillance and image processing systems.
What you need
Features
•
HD-TVI technology transmits zero latency HD video resolution over coax cabling
•
1280 x 720 (720p @ 30 fps) HD video for sharp, detailed images
•
2.8 mm wide angle lens (ALI-BC1720G only) captures images over large areas
•
Built-in 24 LEDs enables the camera to see up to 65 ft in the dark
•
Smart IR technology reduces over-exposure of the IR LEDs at the center of the image
•
True day/night (ICR) captures sharp, clear images in low light and at night
•
-40°F ~ 140°F extreme temperature operating range
•
IP66 weather-rated metal (ALI-BC1720E) or ABS (ALI-BC1720G) housing
To install the camera, you will need:
•
•
•
•
•
12 Vdc power source. See Specifications for wattage requirement.
Tools and additional fasteners (may be required) for mounting the camera
Phillips screwdriver
Video and power extension cable
HD-TVI video setup monitor (optional)
Installation
Before installation:
Mounting base
•
•
•
•
Adjustable
mounting
bracket
Make sure that the device is in good condition and all the assembly parts are included.
Check the specification of the products for the installation environment.
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specifications section.
During installation:
•
•
Camera body
Lens
IR LED Array
ALI-BC1720E camera
Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the Cleaning section.
Power supply: Camera drop cable: The camera drop cable includes two connectors:
—— Video BNC connector: For transmission of the video signal across a coax (75 Ω) extension cable
to an HD-TVI compatible recorder.
—— Power connector: When applying power, observe the power polarity. See the picture to the
right for the connector polarity configuration.
Mounting the camera
An ALI-BC1720 series camera can be mounted on a wall or ceiling that has sufficient strength to support it.
The video/power drop cable from the camera can be routed either through mounting surface or through a
cable guide in the mounting base.
Mounting base
Mounting
Bracket
Adjustments
Camera body
IR LED Array
Lens
ALI-BC1720G camera
ALI-BC1720 series camera typical ceiling mounting
HD-TVI Video
BNC Connector
NOTE
1.
Power Connector
ALI-BC1720 series camera drop cable connectors
1
www.observint.com
If mounting the camera on a wall, ensure that the cable guide in the mounting base is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable guide is pointing
away from any source of water, dust, and other contaminates.
Using the drill template provided, mark the location of the screws that anchor the mounting base
to the mounting surface. See the note above. If you are routing the drop cable through mounting
surface, also mark the position of the hole for the drop cable.
ALI-BC1720_CQ
8/26/15
2.
Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface materials, more
appropriate fasteners may be required.
3.
If routing the drop cable through the mounting surface, drill a 5/8” hole in the middle of the drill
template.
4.
Route the drop cable through the hole in the mounting surface, or through the cable guide in the
mounting base, then attach the camera assembly to the surface using the appropriate fasteners.
5.
Connect the camera drop cable to video and power extension cables as required.
6.
Connect the other end of the video extension cable to a HD-TVI compatible video monitoring device,
such as a HD-TVI digital video recorder (DVR).
Drop cable connectors are not waterproof.
NOTE
7.
Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
Camera adjustments
1.
Apply power to the camera.
2.
Verify that video from the camera can be seen on the monitor.
3.
While observing video from the camera, loosen the mounting bracket pan lock nut, and elevation
and horizontal line adjustment lock screws, point the camera at your surveillance target, and then
tighten adjustment lock screws and nut to hold the camera in position.
Use for horizon line
adjustment
Use for pan
adjustment
(lock nut)
Use for
elevation
adjustment
0° ~ 360°
0° ~ 90°
0° ~ 360°
ALI-BC1720 series camera mounting bracket adjustment
Troubleshooting
Problem
Possible Cause
Nothing appears on the screen
- Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
The screen is dark.
- Adjust the contrast control of the monitor.
- Set the monitor impedance properly for the DVR (usually 75 Ω /Hi-Z),
and check the cable connections.
The camera is not working properly and the
surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor flickers
- Make sure that the camera isn’t facing direct sunlight or fluorescent light.
If necessary,change the camera position.
Specifications
Camera
ALI-BC1720E
ALI-BC1720G
Image Sensor
Progressive Scan CMOS
Progressive Scan CMOS
Effective Pixels
1280(H) * 720(V)
1280(H) * 720(V)
Min. Illumination
0.01 lux @ (F1.2, AGC on), 0 lux with IR
0.01 lux @ (F1.2, AGC on), 0 lux with IR
Shutter Time
1/30 s to 1/50,000 s
1/30 s to 1/50,000 s
Lens
3.6 mm Angle of View: 71°
2.8 mm; Angle of View: 92˚
Lens Mount
M12
M12
Angle Adjustment
Pan: 0 ~ 360°, Tilt: 0 ~ 90°, Rotation: 0 ~ 360°
Pan: 0 ~ 360°, Tilt: 0 ~ 90°, Rotation: 0 ~ 360°
Day & Night
ICR
ICR
Synchronization
Internal synchronization
Internal synchronization
Video Frame Rate
720p @ 30 fps
720p @ 30 fps
HD Video Output
1 HD-TVI output
1 HD-TVI output
Enclosure color
White
Gray
Working Temperature/
Humidity
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity 90% or less (non-condensing)
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity 90% or less (non-condensing)
Power Supply
12 Vdc
12 Vdc
Power Consumption
Max. 4 W
Max. 4 W
Weather Proof Ratings
IP66
IP66
Case
Metal
ABS
General
IR Range
Up to 65 ft (20 m)
Up to 65 ft (20 m)
Maintenance
Dimension
Φ2.76" × 5.89" (Φ70 × 149.5 mm)
Φ2.76" × 5.89" (Φ70 × 149.5 mm)
Cleaning
Weight
0.79 lb (378 g)
0.41 lb (184 g)
Clean the camera glass with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.

CAUTION
2
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
www.observint.com
© 2015 Observint Technologies. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising