S6 Austenitic Stainless Steel Separator

S6 Austenitic Stainless Steel Separator
Local regulations may restrict the use of this product to below the conditions quoted.
In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2015
TI-P023-12
ST Issue 11
S6
Austenitic Stainless Steel
Separator
Description
The S6 is an austenitic stainless steel (316L) baffle type separator
used for the removal of entrained liquids in steam, compressed air
and gas systems.
Optional extras
Insulation jackets are available which will increase the performance
of the separator, (see TI-P138-01).
Standards
This product fully complies with the requirements of the European
Pressure Equipment Directive 97 / 23 / EC and carries the mark
when so required.
Certification
This product is available with certification to EN 10204 3.1.
Note: All certification / inspection requirements must be stated
at the time of order placement.
5
4
Sizes and pipe connections
½", ¾", 1", 1¼", 1½" and 2"
Screwed BSP or NPT, butt weld, socket weld.
DN15, DN20, DN25, DN32, DN40 and DN50.
Flanged EN 1092 PN40 with screwed BSP drain and air vent.
Flanged BS 1560 (ASME B 16.5) Class 150 or 300 with
screwed NPT drain and air vent.
Flanged JIS 2201 / KS 10K and 20K with
screwed BSP drain and air vent.
Note: For larger sizes use an S8 separator. See TI-P138-10.
2
1
Temperature °C
Pressure / temperature limits
B AC
DE F
G
Steam
saturation
curve
4
Flanged S6 shown
3
A-A
B-B
C-C
D-D
E-E
F-F
G-G
D
A C B
Pressure bar g
E
F G
The product must not be used in this region.
Flanged JIS / KS 10K
Flanged ASME Class 150
Flanged EN 1092 PN16
Flanged JIS / KS 20K
Flanged EN 1092 PN40
Flanged ASME Class 300
Screwed BSP, NPT, socket weld and butt weld
Body design conditions PN50 / ASME 300
PMA Maximum allowable pressure
50 bar g @ 50°C
TMA Maximum allowable temperature
425°C @ 28 bar g
Minimum allowable temperature
-10°C
JIS / KS 10K
9.9 bar g
PN16
11.4 bar g
ASME 150
11.4 bar g
Maximum operating pressure
PMO
JIS / KS
20K
23.5
bar g
for saturated steam service
PN40
25.8 bar g
ASME 300 27.9 bar g
Scrd / SW / BW 34.1 bar g
TMO Maximum operating temperature
425°C @ 28 bar g
Minimum operating temperature
0°C
Designed for a maximum cold hydraulic test pressure of 76.6 bar g
Materials
No.Part
Material
Austenitic 1.4409 / ASTM A351CF3M
stainless steel 316L
DIN 17440 x2CrNi Mo 17 3 2 (1.4409) /
2Flange Austenitic
stainless steel
ASTM A182 F316L
Austenitic
ASTM A351
3Cap
stainless steel
Gr. CF8M (316)
Cap 4
gasket Reinforced exfoliated graphite
Austenitic ASTM A351
5Cap
stainless steel
Gr. CF8M (316)
1Body
Dimensions
(approximate) in mm
Screwed
ASME ASME JIS / KS Size
SW, BW PN16
PN40
150
300 10K & 20K
A A AAA ABC DFGH
DN15 - ½" 130 - 204204204 204150294 68 1" ½"90
DN20 - ¾" 130 - 212212212 212146347 68 1" ½"90
DN25 - 1" 178
-
260 260 260 260 170.5386 68 1" ½"127
DN32 - 1¼"190 - 274 274 274 274 195 440 68 1" ½"141
DN40 - 1½"220 - 310 310 310 310 208 508 68 1" 1" 168
DN50 - 2" 214 - 310310310 310208558 68 1" 1" 168
Weights /volume (approximate) in kg and litres
SizeWeight Volume
Scrd /SW/BWFlanged Scrd /SW/BW Flanged
DN15 - ½"
5.8
7.4 0.71
0.72
DN20 - ¾"6.8 9.1 0.90 0.92
DN25 - 1"11.9 14.8 2.83 2.86
DN32 - 1¼"15.9 18.6
4.15
4.19
DN40 - 1½"22.0 25.5
6.93
7.00
DN50 - 2"23.9 29.1 7.74
7.88
H
G Air vent
5
Safety information, installation and maintenance
For full details see the Installation and Maintenance Instructions
(IM-P023-55) supplied with the product.
Installation note:
Install in a horizontal pipeline with the drain directly below.
To ensure that any separated liquid is drained quickly, a suitable
steam trap / liquid drainer must be connected to the drain connection.
For those steam systems where air can be present, air can collect in
the upper portion of the separator. In this situation a suitable
air vent should be connected to the air vent connection.
If an air vent is not being fitted then the connection must have the
plastic transit protection plug removed and must have a stainless
steel class 3 000 lb plug fitted.
C
B
Disposal:
The product is recyclable. No ecological hazard is anticipated with
disposal providing due care is taken.
How to order
3
Example: 1 off Spirax Sarco DN20 S6 separator with an austenitic
stainless steel body flanged to EN 1092 PN40.
F Drain
D
A Scrd /SW/BW
A Flanged
Recommended tightening torques
Items
3 and 5
S6 Austenitic Stainless Steel Separator
Nm
46 A / F
180 - 200
TI-P023-12 ST Issue 11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising