FGDF10.G
FGDF710-10-1G FGDF710-10-2G
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
SEE FIG. 4
7
SEE FIG. 3
9
27
13
14
25, 8
15
23
17, 18, 19, 20
28
24
16
21, 22, 32
29, 30, 31
26
FIG. 1
FGDF710-10-1G SHOWN
PAGE 1
98361C (05/07)
98361C (05/07)
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED)
TO ACCEPT 3/8 O.D. UNPLATED COPPER TUBE.
POSICIÓN DE ABASTECIMIENTO DE AGUA RECOMENDADA. VÁLVULA CERRADA (NO AMUEBLADO)
PARA ACEPTAR 3/8" O.D. TUBO DE COBRE NO PLATEADO.
ENDROIT D’APPROVISIONNEMENT EN EAU RECOMMANDÉ. LA VALVE ARRÊTÉE (NON FOURNI)
POUR ACCEPTER 3/8" PO. (9,5mm) TUBE COULEUR CUIVRE NON PLAQUÉ.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1-1/4" DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED
PURGADOR DE 1-1/4 NO PROPORCIONADO
SIPHON 1-1/4 NON FOURNI
PAGE 2
D = POWER CORD 4 FEET (1219mm) LONG
CABLE ELÉCTRICO DE 4 PIE (1219mm), DE LARGO
CORDON D’ALIMENTATION 4' (1219mm)
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA
REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE ET LE
MUR.
F = TO LEVEL UNIT, LOOSEN SCREWS TO ADJUST BASE FOR CONTACT WITH FLOOR. TIGHTEN SCREWS AFTER UNIT HAS
BEEN LEVELED.
PARA NIVELAR LA UNIDAD, AFLOJE LOS TORNILLOS PARA AJUSTAR LA BASE PARA QUE HAYA CONTACTO CON EL PISO.
APRIETE LOS TORNILLOS DESPUÉS DE QUE SE HAYA NIVELADO LA UNIDAD.
POUR NIVELER L’UNITÉ, DESSERREZ LES VIS POUR AJUSTER LA BASE AU CONTACT AVEC LE PLANCHER. SERREZ LES
VIS APRÈS QUE L’UNITÉ AIT ÉTÉ NIVELÉE.
FIG. 2
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
LÍNEA DE LA PARED
LIGNE DU MUR
FGDF710-10-1G FGDF710-10-2G
FGDF710-10-1G FGDF710-10-2G
Note: When installing replacement bubbler, tighten nut (Item 12)
only to hold parts snug in position. Do not over tighten.
10
11
12
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
remove Items 1 & 2 and adjust screw on Item 4. Clockwise adjustment will raise
stream and counter-clockwise adjustment will lower stream. For best adjustment,
stream should hit basin approximately 6-1/2" (165mm) from bubbler.
1
2
3
4
5
BASIN
6
FIG. 4
PAGE 3
98361C (05/07)
FGDF710-10-1G FGDF710-10-2G
PARTS LIST 115V
ITEM NO.
PART NO.
1
2
3
4
5
6
7
40089C
40048C
15005C
61313C
40169C
50986C
21781C
21782C
50189C
56092C
98118C
100322740560
15009C
55996C
66506C
31513C
31501C
31490C
30664C
70018C
20282C
50144C
19037000
66203C
66558C
66764C
20460C
21482C
21239C
21486C
35774C
35768C
36222C
36221C
75706C
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
*28
29
30
31
32
PARTS LIST 230V-50/60Hz
DESCRIPTION
ITEM NO.
PART NO.
7
14
16
17
23
24
*28
30
31
22543C
66505C
31505C
31430C
66202C
66508C
36085C
36195C
36050C
Cover
Button
Regulator Retaining Nut
Regulator
Hex Nut
Regulator Holder
Basin & Drain Assy.
Basin & Drain Assy. (GF)
Fan - Shroud
Poly Tubing (Cut To Length)
Bubbler Assembly
Washer
Bubbler Nipple
Strainer
Evaporator Assy
Cold Control
Power Cord
Fan Motor
Fan Blade
Fan Blade Nut
Fan Motor Bracket
Grommet - Compressor Mtg.
Clip - Compessor Mtg.
Drier
Heat Exchanger
Condenser
Front Panel (Stainless Steel)
Front Panel (Sandalwood)
Cabinet (Stainless Steel)
Cabinet (Sandalwood)
Compressor Serv. Pak FF10HBK
Cover - Relay
Overload
Relay
Stud - Compressor Mtg.
DESCRIPTION
Basin & Precooler Assy.
Evaporator Assy.
Power Cord
Fan Motor
Drier
Heat Exchanger
Compressor Serv Pak
Overload
Relay
*REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to ELKAY water coolers or orders
for repair parts MUST include Model No. and Serial No. of cooler, name
and part number of replacement part.
Glass Filler Shown for Reference Only.
Llenador de cristal demostrado para la
referenia solamente.
Remplisseur de verre montré pour la
référence seulement.
FIG. 5
BASIN
11
12
PRINTED IN U.S.A.
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
98361C (05/07)
PAGE 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising