User’s Guide model 30551 Introduction

User’s Guide model 30551 Introduction
Introduction
User’s Guide
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed.
Refer to the Important safety instructions section in this book and
save them for future reference.
This 30551 telephone is compliant with the DECTTM standard. It is designed to
transmit and receive telephone calls and be collected to the certain public
telephonic networks.
*DECT is the trademark registered by ETSI.
model 30551
IMPORTANT: Because cordless phones operate on electricity, you should have
at least one phone in your home that isn’t cordless, in case the power in your
home goes out.
Before you begin
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a
modular jack, call your local phone company to find
out how to get one installed.
Wall plate
Basic Base
Display language
CAUTION: Use only the power adaptor that came with this unit.
Base: S003IV0600050, 6Vdc/500mA. Charger: S003IV0600015,
6Vdc/150mA).
Using other power adaptors may damage the unit.
Find
Power adaptor
30551xE2 : 1
30551xE3 : 2
30551xE4 : 3
Telephone
base 30551
Handset
30551xE1 : 1
30551xE2 : 2
30551xE3 : 3
30551xE4 : 4
DECT
Cordless Telephone
Charging cradle
30551xE2 : 1
30551xE3 : 2
30551xE4 : 3
Power adaptor
for telephone
base 30551
Your new GE telephone system is EXPANDABLE up to 4 handsets
Telephone
line cord
Battery compartment
cover
30551xE1 : 1
30551xE2 : 2
30551xE3 : 3
30551xE4 : 4
User’s manual
OK
Talk
Menu
User’s
manual
Mute
Please Fully Charge Before Using!
For optimum battery performance, charge the battery for 16 hours before use.
Installing the phone
Telephone base and charging cradle installation
Install the telephone base and charging cradle(s) as shown below. Make sure that
the electrical outlet is not controlled by a wall switch.
If you have DSL high speed internet service, a DSL filter is required (not included).
Contact your DSL service provider for more information about DSL filter.
Battery
Battery
indicator
]: “PERSONAL SET”
1. [ menu ]
3. [
]/[
]: “HANDSET TONE”
4. [
]/[
]: “RINGER VOLUME”
5. [
]/[
]: Select the desired setting (VOLUME 1 to 4 and OFF)
[ ok ]
2. [
]/[
]: “PERSONAL SET”
3. [
]/[
]: “LANGUAGE”
4. [
]/[
]: Select the desired setting
5. [ ok ]
[
[ ok ]
]: “ADVANCED SET”
3. [
]/[
]: “DIAL MODE”
4. [
]/[
]: Select the desired setting
#/Ringer Off
Intercom/Conference
]/[
]: “CLOCK&ALARM”
3. [
]/[
]: “DATE/TIME”
[ ok ]
[ ok ]
4. Enter the current year, month and date by selecting 2 digits.
Example: May 16, 2010
[1][0][0][5][1][6]
5. Enter the current hour and minutes by selecting 2 digits.
Example: 9:30 am
[0][9][3][0]
[
]/[
]: Select am or pm
[
]
6. [ ok ]
Note: You can change date and time display format
Date format
2. [
]/[
]: “CLOCK&ALARM”
3. [
]/[
]: “SET FORMAT”
4. [
]/[
]: “DATE FORMAT”
]/[
[ ok ]
[ ok ]
[ ok ]
]: Select the desired setting (MM/DD OR DD/MM)
6. [ ok ]
Handset Display Items
Time format
[
]
1. [ menu ]
• Turn on when base unit in range
• Blinking when base out of range
2. [
]/[
]: “CLOCK&ALARM”
• Turn on during review the phone book
3. [
]/[
]: “SET FORMAT”
• Turn on when battery full
• Slow flash when battery less than 50% capacity
• Fast flash when battery less than 25% capacity
4. [
]/[
]: “TIME FORMAT”
5. [
]/[
]: Select the desired setting (12 HOURS OR 24 HOURS)
• Turn on when Alarm set
• Turn on when ringer off set
• Blinking when there is a missing call
• Turn on during review the call log and there is old record(s) in call log
• Turn on when handset in spearkerphone mode
6. [ ok ]
[
1. [ menu ]
]/[
]: “PERSONAL SET”
3. [
]/[
]: “HANDSET TONE”
4. [
]/[
]: “RING TONES”
5. [
]/[
]: Select the desired setting (MELODY 1 to 10)
[
[ ok ]
[ ok ]
Phonebook
Adding record
]
1. [ menu ]
Adjusting the receiver volume
] or [
When a call is being received, the LCD and keypad backlight flash rapidly
1. Lift the handset and press [
] when the unit rings
2. When you finish talking, press [
] or place the handset on the base unit
or charger
Conference
[ ok ]
[ ok ]
[ ok ]
]
Note: To display date and time, press and hold the [BACK] button when handset is
in standby mode.
] when other handset is on an outside call.
Making a call using the redial list
The last 5 numbers dialed are stored in the redial list (each 24 digits max)
]
2. press [
]/[
3. Press [
]
2. [
]/[
]: “PHONEBOOK”
3. [
]/[
]: “NEW ENTRY”
]: Select the desired phone number
[ ok ]
Character Table for the entering names
Key
Character
[1]
Space 1 < > *
[2]
ABC2
[3]
DEF3
[4]
GHI4
[5]
JLK5
[6]
MNO6
[7]
PQRS7
[8]
TUV8
[9]
WXYZ9
[0]
0-/\#+
Correct the mistake
Press [
] to delete the characters or numbers
View record
1. [ menu ]
]/[
] : “PHONEBOOK”
1. Press [
]
3. [
]/[
] : “LIST”
2. Press [
]/[
]: Select the desired phone number
]: “DELETE” or “DELETE ALL
[
]
[ ok ]
4. Press [ ok ] to confirm
Other Feature during a call
Mute
While mute is turned on, you can hear the other party, but the other party
cannot hear you.
1. Press [
[ ok ]
]
2. [
]/[
[ ok ]
5. Enter the number (max. 24 digits)
Erasing a number in redial list
3. [
[ ok ]
4. Enter the name (max. 12 character)
6. [
] repeatedly while talking
Answering calls
1. Press [
].
Note: A 3 second pause is inserted each time, repeat as needed to create longer
pauses
1. Lift the handset and dial the phone number
To correct a digit, press [
]
2. Press [
]
3. When you finish talking, press [
] or place the handset on the base unit
or charger.
Press [
A pause is sometimes required when making calls using a PBX or long distance
service. When storing a calling card access number and/or PIN in the phonebook,
a pause is also needed.
]
1. Press [ 9 ], then long press [
2. Dial the phone number and press [
[ ok ]
2. [
6. [ ok ]
Pause (for PBX/long distance service users)
Example: If you need to dial the line access number “9” when making outside calls
with PBX:
To join the conversation, press [
1. [ menu ]
5. [
]
Making calls
2. [
Display
Meaning
[ ok ]
]
1. [ menu ]
Redial
[ ok ]
]/[
[
[
R ] to answer the 2nd call
2. To switch between calls, press [ R ]
1. Press [
[ ok ]
Ringer Tone
2. [
5. [ ok ]
6. [ ok ]
[ ok ]
Note: If Ringer off is selected, there is no preview during the ringer melody selection.
]
End/Power off
• Blinking when there is Voice mail
is a trademark of
The General Electric Company
and is under license by
CCT Tech Global Limited,
Central, Hong Kong
]/[
Date and time
• Blinking when there is incoming call
• Steady on during a call
Model 30551
P/N:XXXXXXXX
CE.E Version 1.0 05/2011
Printed in China
© 2011 CCT Tech Global Limited
2. [
Back/Delete
Down/Phonebook
OK: Press to select an item, or save an entry or settings.
Back/Delete: Press to delete the last input number or letter. While in a menu, press to
return the upper level without making changes.
Up/CID: Press to review the call log when the telephone is not in use. While in a
menu, press to scroll up. During a call, press to increase the listening volume.
Down/Phonebook: Press to review the phonebook when the telephone is not in use.
While in a menu, press to scroll down. During a call, press to decrease the listening
volume.
Talk: Press to make or answer a call. Toggle between receiver and speakerphone
mode
Flash: Press to answer a call when you receive a call waiting alert.
End/Power off: During a call, press to hang up. During a programming, press to exit
without making changes. Press and hold to power off the handset
Menu: Press to show menu.
Redial: Press to review redial list.
*/Keylock: Press and hold to set the keylock (Keylock will de-activate when handset
sit on the charge cradle)
#/Ringer off: Press and hold to set the Ringer off when the telephone is not in use.
Mute: While on a call, press to mute the microphone.
Intercom/Conference: Set up the intercom between handset to handset. Press and
hold to make conference call during intercom mode
Item
Flashing
Display
Flash
Battery
30551xE1 : 2
30551xE2 : 4
30551xE3 : 6
30551xE4 : 8
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
www.thehomephones.com
1. Make sure the battery compartment cover is not attached with the handset.
2. Insert the AAA rechargeable batteries as shown on the engraving in the battery
compartment.
3. Align the cover against the battery compartment and slide it upwards until it
clicks into place.
4. Charge the handset by placing it in the telephone base. The light on the
handset is on when charging.
* / Keylock
Installation
visit our website:
Up/Caller ID
[ ok ]
You can select change the display language.
1. [ menu ]
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
To use call waiting, you must subscribe to call waiting from your service provider.
This feature allows you to receive calls while you are already talking on the phone,
you will hear a call waiting tone. If you subscribe to both Caller ID and Call Waiting
with Caller ID services, the 2nd caller’s information is displayed after you hear the
call waiting tone on the handset.
1. [ menu ]
If you cannot make calls, change this setting according to your telephone line
service. The default setting is “TONE”
Handset layout
For Call waiting or Call Waiting Caller ID service subscriber
Ringer Volume
Dialing mode
Find: Press to page all system handsets
CAUTION: To reduce the risk of fire or personal injury, use only the CCT
Tech Global Limited approved Nickel-metal Hydride battery (Ni-MH) 1.2V
AAA size 400mAh (SHP or Sanik) which is compatible with this unit.
Make sure your package includes the items shown here.
Initial settings
Modular
telephone line
jack
Installing the Handset Battery
Parts Checklist
Base layout
] during the call
2. To return the call, Press [
] again
Note: LCD will show “MUTE ON” when mute feature activated
[ ok ]
[ ok ]
4. Press [ ok ] to view the name and number
5. Press [
OR
6. Press [
] to dial out if necessary or press [
] at idle and repeat step 3
Make a call from phonebook
1. [
]
2. [
]/[
3. [
]
] : Select the desired record
] to return idle
Searching by first character
Alarm
4. Enter you PIN (default PIN: 0000)
1. [
An alarm sounds at the set time for 1 minute once or daily. Alarm can be set for
each handset.
5. [
]
2. Press [1] – [9] which contains the character you are searching for
3. [
4. [
]/[
Important: Set the date and time beforehand
] : Select the desired record if necessary
2. press [
]/[
] to select “CLOCK&ALARM”.
Editing entries
3. Press [
]/[
] to select “ALARM”.
4. Press [
]/[
] to select the desired alarm option.
2. [
]/[
[ menu ]
] : “EDIT ENTRY”
4. Edit the number if necessary
5. [
[ ok ]
]
Erasing entries
1. Find the desired record
2. [
]/[
IMPORTANT:
In order to use this unit’s Visual Message Waiting Indicator (VMWI) feature, you
must subscribe to this service from your phone company.
]/[
] to select “CLOCK&ALARM”.
[ ok ]
3. Press [
]/[
] to select “ALARM MELODY”.
[ ok ]
Programming the Telephone
4. Press [
]/[
] to select the desired alarm tone.
Receiving CID Records
Making an intercom call
Storing CID Records (In CID Memory)
1. [
]
2. Select the handset you want to page by pressing the desired handset
number ([1] –[4]) or you can page all handset by pressing [ ]
3. When you finish talking, press [
]
Standby Screen
5. Alarm melody set and press [
As calls are received and stored, the display is updated to let you know how
many calls have been received. To scroll CID records:
1. [
[ ok]
] return to idle
PIN (Personal Identification Number)
Important: If you change the PIN, please make note of your new PIN. The unit will
not reveal the PIN to you. If you forget your PIN, please reset your phone.
The default PIN is 0000
Intercom
This unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date, and time; or
the name, phone number, date, and time.
Reviewing CID Records and call back
]
2. Press [
] to search from the most recent call, or [
the oldest call.
] to search from
Note: No handset number is needed in a two registered handset system.
1. Press [
] to answer the page
2. When you finish talking, press [
]
Handset locator
Editing a caller’s phone number calling back
1. [
Transferring calls
You can edit a phone number in the caller list by removing its area code and/or
the long distance code “1”
Important safety intructions
Telephone general use
Some of the following information may not apply to your particular product;
however, when using telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to persons,
including the following:
Problem
Cause/solution
The handset does not turn on
- Place the handset on the base unit or charger to turn
even after installing battery pack on the handset.
Cannot hear a dial tone
- Make sure the battery pack is installed correctly.
- Fully charge the battery. Check the connections.
(for 16 hours)
- Unplug the base unit's AC adaptor to reset the unit.
Reconnect the adaptor and try again.
- The handset has not been registered to the base unit.
Register the handset.
- The base unit's AC adaptor or telephone line cord is not
connected. Check the connections.
- Disconnect the base unit from the telephone line and
connect the line to a known working telephone. If the
working telephone operates properly, contact our service
personnel to have the unit repaired. If the working
telephone does not operate properly, contact your service
provider/telephone company. The ringer volume is turned
off. Adjust the ringer volume.
Handset does not ring
- The handset may be out of range of the base.
Move closer to the base.
- The handset may be out of range of the base.
Move closer to base.
You experience static, noise, or
fading in and out
- You are using the handset or base unit in an area with
high electrical interference. Reposition the base unit and
use the handset away from sources of interference.
Answering an intercom call
You can locate a misplaced handset by paging it.
1. Base unit: [
]
All register handsets beep for 1 minute.
2. To stop paging:
Base Unit: Press [
]
Handset: Press [
]
3. To Call back, press [
]
To Exit, press [
] return to idle
Troubleshooting guide
The unit does not work
Intercom calls can be made between handsets
Note:
If you receive an outside call while talking on the intercom, you will hear a beep.
To answer the call with the handset, press and hold [ ] to switch the outside call
and the intercom. While paging a handset, the paged handset beeps for 1 minute.
If you are not at home or cannot answer, your telephone’s Caller ID memory
stores the data for the 10 most recent calls. When the 11th call is received, the
oldest Caller ID record (1st call) is automatically deleted.
2. press [
]
]
Caller ID records are stored in the order that they are received.
1. [ menu ]
3. Press [ ok ] to confirm
4. [
[ ok ]
You can select from 3 alarm melody
[ ok ]
The [
] on the LCD will flash when you receive a new message from your
service provider.
IMPORTANT: In order to use this unit’s Caller ID features, you must subscribe
to either the standard Name/Number Caller ID Service or Call Waiting Caller
ID Service. To know who is calling while you are on the phone, you must
subscribe to Call Waiting Caller ID Service.
[ ok ]
Alarm melody:
[ menu ]
] : “DELETE” or “DELETE ALL”
[ ok ]
OFF: Turns alarm off. (Go to step 6)
ON ONCE: An alarm sounds once at the set time
ON DAILY: An alarm sounds daily at the set time.
5. Set the desired time.
6. Alarm set (or turned off) and press [
] return to idle
[ ok ]
3. Edit the name if necessary
6. [
Voice mail service
[ ok ]
]: Select the desired handset
Using Caller ID service
1. [ menu ]
]
1. Find the desired record
]/[
[ ok ]
Programmable settings
You can customize the unit by programming the following features using
the handset.
Programming by scrolling through the display menus
To change PIN:
1. [ menu ]
1. [ menu ]
[ ok ]
2. Press [
] or [
] to select the desired main menu.
3. Press [
] or [
] to select the desired item in sub-menu 1.
• In some cases, you may need to select from sub-menu 2.
4. Press [
] or [
] to select the desired setting.
[ ok ]
[ ok ]
• This step may vary depending on the feature being programmed
• To exit the operation, press [
]
Main Menu
PHONEBOOK
PERSONAL SET
Sub-menu 1
Sub-menu 2
NEW ENTRY
LIST
EDIT ENTRY
DELETE
DELETE ALL
DIRECT MEM
HANDSET NAME
HANDSET TONE
SET FORMAT
ALARM
ALARM TONE
CHANGE PIN
ADVANCED SET
REGISTRATION
UNREGISTER
RESET
AUTO PREFIX
RECALL TIME
DIAL MODE
FIRST RING
]/[
] to select “ADVANCED SET”
3. Press [
]/[
] to select “CHANGE PIN”
[ ok ]
[ ok ]
4. Input the old PIN code
[ ok ]
5. Input the new PIN code
[ ok ]
6. A beep will sound if the PIN code change is successful.
Additional handset
The base unit of this telephone can support up to a total of 4 cordless handsets.
The handsets that ship with your main base are pre-registered in the factory.
To add or re-register a handset:
] for 5 seconds.
Handset:
2. [ menu ]
RING VOLUME
RING TONES
KEY BEEP
DATE FORMAT
]/[
] to select the desired record
3. [
]/[
] : “ADVANCED SET”
[ ok ]
4. [
]/[
] : “REGISTRATION”
[ ok ]
[ ok ]
3. If the desired record is a name, Press [ ok ] to show the number
4. [
]
OR
You can edit the number you want
]
2. Press [
]/[
] to select the desired record
3. Press [
]/[
] to select “EDIT ENTRY”
]
2. [
]/[
]: Select the desired record
[ menu ]
3. [
]/[
]: “DELETE” or “DELETE ALL”
[ ok ]
Handset:
7. Handset will give a long beep when successfully registered.
5. [
Note: An error tone will sound if the registration is not successful.
Important: The unit shall able to register with 30550 handset only.
Store a CID record
1. [ menu ]
3. [
]/[
]/[
]: “ADVANCED SET”
]: “UNREGISTER”
[ ok ]
[ ok ]
]
] to dial the
CAUTION: To reduce the risk of fire or personal injury, use only the CCT
Tech Global Limited approved Nickel-metal Hydride battery (Ni-MH), which
is compatible with this unit.
1. Make sure the telephone is OFF (not in TALK mode) before you replace the battery.
2. Remove the battery compartment door.
3. Disconnect the cord attached to the battery pack and remove the battery pack
from the handset.
4. Insert the new battery pack and connect the cord to the jack inside the battery
compartment.
5. Put the battery compartment door back on.
6. Place handset in the base or handset charge cradle to charge. Allow the
handset battery to properly charge (for 16 hours) prior to first use or when
you install a new battery pack. If you do not properly charge the phone,
battery performance will be compromised.
Battery Safety Precautions
1. [
]
2. [
]/[
]: Select the desired record
3. [
]/[
]: “SAVE NUMBER”
4. Enter the name and number
5. [
Changing the battery
[ ok ]
1. [
4. Press [ ok ] to confirm
2. [
[ menu ]
4. Enter the number if necessary
5. Press [ ok ] to save the new number in the record or press [
number
6. Handset will show “WAITING”
Deregistering a handset
Outside calls can be transferred or a conference call with an outside party
can be made between 2 handsets.
1. During outside call, press [
]
2. Select the handset you want to page by pressing the desired handset
number ([1] –[4]) or you can page all handset by pressing [ ]
3. Press [
]
4. The call will transfer to the paged handset
For conference call
]
5. Setup a intercom during a call, and long press [
6. LCD will show “CONFERENCE”
[ ok ]
Delete a CID record
5. Enter you PIN (default PIN: 0000)
TIME FOMRAT
2. Press [
1. [
Registering a handset
Base:
1. Press and hold the [
LANGUAGE
AUTO HANG - UP
DATE/TIME
CLOCK&ALARM
[ ok ]
2. press [
]
]
[ ok ]
[ ok ]
[ menu ]
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this
type, toxic materials could be released which can cause injury.
• To reduce the risk of fire or personal injury, use only the battery listed in the
User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 day
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
4. Telephones should not be used while you are in a bathtub, shower or pool. Immersion of
the telephone or handset in water could cause an electrical shock.
5. Slots and openings in the cabinet back or bottom are provided for ventilation, to protect it
from overheating. Do not block or cover these openings. Do not block the openings by
placing the product on a bed, sofa, rug, or other similar surface. Do not place this product
in a built-in installation unless proper ventilation is provided.
6. Only operate this product from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your dealer or local
power company.
7. Plug the adaptor into an easily accessible electrical outlet near the equipment.
8. Do not allow anything to rest on the power cord. Do not locate this product where the
cord will be abused by persons walking on it.
9. Do not overload wall outlets and extension cords as this can result in the risk of fire or
electric shock.
10. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
11. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product. If service or repair
work is required, take it to a qualified serviceman. Opening or removing covers may expose
you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
13. Do not expose the product to extreme temperatures such as areas near a hot radiator,
stove or in a hot car. Do not place product upon other consumer electronic products such
as; computer monitors, power amplifiers, etc.
14. Do not place lighted candles, cigarettes, cigars, etc., on the telephone.
15. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
16. Never install or modify telephone wiring during a lightning
17. Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
18. Use caution when installing or modifying telephone lines to prevent electrical shock
and/or fire.
19. Under the following conditions, unplug this product from the wall outlet and refer servicing
to qualified service personnel:
A. The power supply cord or plug is damaged or frayed.
B. The product has been exposed to rain or water.
Caller ID
Problem
Cause/solution
Caller information is not displayed - You must subscribe to Caller ID service from your
service provider/telephone company.
- If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless
telephone line jack, plug the unit directly into wall jack.
- If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit
and the telephone line jack. Contact your DSL/ADSL
provider for details
- The name display service may not be available in
some areas. Contact your service provider/telephone
company for details.
- Other telephone equipment may be interfering with
this unit. disconnect the other equipment and try again.
Caller information is displayed late - Depending on your service provider /telephone
company, the unit may display the caller's information
at the 2nd ring or later.
- Move closer to the base units.
The 2nd caller's information is not - In order to use Caller ID, call waiting, or Call Waiting
displayed during an outside call
Caller ID (CWID), you must first contact your service
provider/telephone company and subscribe to the
desired service.
General product care
To keep your unit working and looking good, follow these guidelines:
• Avoid dropping the handset, as well as other rough treatment to the phone.
• Clean the phone with a soft cloth.
• Never use strong cleaning agents, paint thinner, abrasive powder, alcohol,
or other chemical products to clean the unit. Doing so will damage the finish.
• Retain the original packaging in case you need to ship the phone at a later date.
• Periodically clean the charge contacts on the handset and base with a clean
pencil eraser.
20.
21.
22.
23.
24.
C. The product does not operate normally by following the operating instructions.
D. The product’s cabinet has been damaged.
E. The product exhibits a distinct change in performance.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may
be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
IF YOUR PRODUCT UTILIZES BATTERIES, THE FOLLOWING ADDITIONAL
PRECAUTIONS SHOULD BE OBSERVED:
Use only the type and size battery(ies) specified in the user manual.
Do not use this product if the battery door is removed or missing.
Replace batteries that appear to be swollen or have damaged wiring.
Do not dispose of the battery(ies) in fire. They may explode. Check with local codes for
possible special disposal instructions.
5. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
6. Exercise care in handling battery(ies) in order not to short out the battery(ies) with
conducting materials such as rings, bracelets, and keys. The battery(ies) or conductor may
overheat and cause burns.
7. Do not attempt to recharge the battery(ies) provided with or identified for use with this
product that are not rechargeable. The battery(ies) may leak corrosive electrolyte or explode.
8. Do not attempt to rejuvenate the battery(ies) provided with or identified for use with this
product by heating them. Sudden release of the battery(ies) electrolyte may occur causing
burns or irritation to eyes or skin.
9. When replacing battery(ies), all batteries should be replaced at the same time. Mixing fresh
and discharged batteries could increase internal cell pressure and rupture the discharged
battery(ies). (Applies to products employing more than one separately replaceable primary
battery.)
10. When inserting battery(ies) into this product, the proper polarity or direction must be
observed. Reverse insertion of battery(ies) may result in leakage or explosion.
11. When inserting battery(ies) into this product, do not twist or pinch the wires or allow wires
to become pinched in battery door.
12. If storing over 30 days, remove battery(ies) from this product because the battery(ies)
could leak and damage the product.
13. Discard “dead” battery(ies) as soon as possible since “dead” batteries are more likely to
leak in a product.
14. Do not store this product, or the battery(ies) provided with or identified for use with this
product, in high-temperature areas. Batteries that are stored in a freezer or refrigerator
for the purpose of extending shelf life should be protected from condensation during
storage and defrosting. Batteries should be stabilized at room temperature prior to use
after cold storage.
15. If your product uses rechargeable battery(ies), charge the battery(ies) only in accordance
with the instructions and limitation specified in the User Guide.
Environment
Used equipment must be disposed of in compliance with current environmental
protection regulations. You should return it to you reseller or dispose of it in an
approved recycling centre.
Do not attempt to open the batteries as they contain chemical substances.
In the event of leakage, avoid contact with the skin, eyes and mouth. In the
event of contact, rinse the affected part for several minutes in running
water. Clean the product with absorbent paper or a dry cloth and contact
your reseller for replacement batteries.
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRICAL SHOCK, DO NOT OPEN
THE LIGHTING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU
OF “DANGEROUS
VOLTAGE” INSINDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
WITHIN THE
TRIANGLE IS
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
Declaration of Conformity
We,
CCT TECH GLOBAL LIMITED,
18/F, CCT Telecom Building, 11 Wo Shing Street, Fo Tan, Shatin, NT, Hong Kong
declare under our sole responsibility that the product
1.
2.
3.
4.
Model Name :
30551FE1
30551GE1
30551FE2
30551GE2
is in conformity with the protection requirements
Directive and Commission Regulation
EC R&TTE - Telecommunication Directive 1999/5/EC
Commission Regulation (EC) No 1275 / 2008 implementing Directive 2009/125/EC
Commission Regulation (EC) No 278 / 2009 implementing Directive 2009/125/EC
Test Standard
EN 301 489-01 V1.8.1
: 2008
EN 301 489-06 V1.3.1
: 2008
EN 301 406
: 2009
V2.1.1
EN 60950-1: 2006
+ A11 : 2009
Clause 4 & 5 of EN 62301
Date
: July 2011
: 2005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising