WAE24367GB-EN
Preparation
ʋ for domestic use only,
ʋ for washing machine-washable fabrics and hand-washable wool in detergent solution,
ʋ to be operated with cold drinking water and commercially available detergents and care products which are
suitable for use in washing machines.
Further information: www.bosch-home.com
.
Environmentally friendly waste disposal
Open the washing machine door and remove the washing.
If Rinse Hold (without final spin) is active: Turn the
programme selector to > Drain or select the spin speed.
Press $ Start/Reload.
Sorting and loading laundry
Correct installation according to the
separate Installation instructions.
Follow the manufacturer's care information.
According to the information on the care labels.
According to type, colour, soiling and temperature.
Do not exceed the maximum load a page 7.
Observe the important information a page 6.
Insert large and small items of laundry.
Close the washing machine door. Take care not to trap items of laundry
between the washing machine door and the rubber seal.
Checking the machine
– Never use a damaged machine.
– Inform customer service.
Connecting the mains plug
Make sure your hands are dry.
Take hold of the plug only.
Drum
Turning the tap off
Control panel
Add detergent and care products
Not required for Aqua-Stop models a Refer to installation
instructions.
Washing machine
door
Measure accordingly:
Amount of laundry, soiling, water hardness (ask your water supply
company) and manufacturer's instructions.
Pour liquid detergent into the appropriate dispenser and place in the drum.
Turning the tap on
– Remove any foreign objects - risk of rusting.
– Leave the washing machine door and detergent
drawer open so that any residual water can
evaporate.
Detergent drawer with
compartments I, II, ~
Switching off
Compartment 0: Fabric softener, starch
Hard-wearing fabrics
+ Prewash
Hard-wearing fabrics, pre-wash at
30 °C
/ Mixed Load
Different types of laundry
@ SuperQuick 15’
Short programme
2 Rinse/ Spin
Laundry washed by hand,
= Aqua Plus button activated; if only
using the spin cycle, deactivate the
button
> Drain
Drain rinsing water for Rinse Hold
(without final spin)
ÿ Wool
Hand/machine-washable wool
“ Delicate/Silk
Delicate washable fabrics
I Easy-Care
Easy-care fabrics
Display panel/
Options button
Start/
Reload
Programme selector
Additional functions, the options
button and spin speeds a
Individual settings, page 5.
All buttons are sensitive and need
only to be touched lightly. Press
and hold the options and spin
speed buttons to run through the
setting options automatically.
1
$ Start/Reload
Programme sequence displays:
ü'ü1üü2üü
1 - 24h
Childproof lock, washing, rinsing, spinning
Service flap
2
... you have selected the wrong programme by mistake:
– Reselect the programme.
– Press $ Start/Reload. The new programme starts from
the beginning.
Programme selector for
switching the machine on
and off and for selecting
the programme. Can be
turned in either direction.
Washing
Set to •
Before and while the selected programme is running, you can set the spin speed or Rinse
Hold (without final spin, laundry soaks in the last rinsing water, display - - -). The effects
depend on the programme progress. The maximum selectable spin speed depends on the
model and on which programme is currently selected.
press and hold
1 step, the
display panel
lights up
Information signals
+ 1 step, release
2. Setting the volume
for ...
Additional functions a and overview of programmes, see page 7
For washing in a shorter time with a washing outcome comparable to
that of the standard programme. Maximum load a Overview of
programmes, page 7.
Ĉ EcoPerfect
For saving energy with a washing performance comparable to that of
the standard programme.
S Reduced Ironing Special spin sequence with subsequent fluffing. More gentle final spin
- residual moisture in the laundry slightly increased.
= Aqua Plus
Increased water level and additional rinse cycle, extended washing
time. For areas with very soft water or for further enhancing the spin
result.
Childproof lock and reloading
'
Childproof lock/
Appliance lock
You can lock the washing machine to prevent the functions you have
set from being changed inadvertently.
ON /OFF: Press and hold the $ Start/Reload button for approx. 5
seconds after the start/end of the programme.
Note: The childproof lock can remain activated until you wish to start
the next programme, even after switching off the machine.
Then you can deactivate the childproof lock before the start of the
programme and activate it again as necessary once the programme
has started.
If you want to add additional items of laundry after the programme has
started, choose $ Start/Reload. The machine checks whether
reloading is possible.
YES is lit: Reloading is possible.
NO flashes: wait until YES lights up.
Note: do not open the door until YES is lit.
NO: It is not possible to reload.
Note: For safety reasons, the washing machine door remains locked
when the water level and/or temperature is high, or during spinning.
To continue the programme, press the $ Start/Reload.
$ Start/Reload
To start the programme or to subsequently load additional laundry, and to activate/deactivate
the childproof lock.
Reloading laundry, if ... a page 5
* you may need to select Setting the
the function several times. volume*
direct
1 step
Setting the
volume*
Set to •
Important information
Protecting the laundry and the machine
– When determining the dosage of all washing powders, additives and cleaning agents, you
must follow the manufacturer's instructions.
– Empty pockets.
– Look out for metal items (paperclips, etc.).
– Wash delicates in a laundry bag (tights, curtains, underwired bras).
– Fasten zips, do up any buttons.
– Brush sand out of pockets and collars.
– Remove curtain fittings or place in the laundry bag.
Laundry with varying degrees of soiling
Wash new items of clothing separately.
Do not pre-wash. If required, choose the additional function
ĉ SpeedPerfect.
Pre-treat any stains as necessary.
intense
Do not load as much laundry.
Choose a programme with pre-wash.
Soaking Load laundry of the same colour
Pour soaking agent/detergent into compartment II in accordance with the manufacturer's
instructions. Turn the programme selector to LF Cottons 30 °C and press $ Start/Reload.
After approx. 10 minutes, press $ Start/Reload to pause the programme. Once the required
soaking time has elapsed, press $ Start/Reload again to continue the programme, or select
a different programme.
Starching Laundry must not be treated with fabric softener
light
Starching is possible in all wash programmes if liquid starch is used. Pour the starch in
accordance with the manufacturer's instructions into fabric softener compartment ~ (rinse first
if necessary).
Dyeing/Bleaching
Dye should only be used in normal household quantities. Salt may damage stainless steel.
Always follow the dye manufacturer's instructions! Do not use the washing machine for
bleaching clothes!
... $ Start/Reload selected and then YES is lit in the
display panel. If NO is lit, the washing machine door
cannot be opened.
– Press $ Start/Reload.
3
Button signals
ĉ SpeedPerfect
YES
Reload
ʑ
1200
1000
800
600
Rinse Hold
1. Activating the mode
for setting the signal
volume
Spin c/ without final spin
Changing the programme, if ...
Programme end after
2
Programmes at high temperatures:
– Cool washing: Select Rinse/ Spin.
– Press $ Start/Reload.
Programmes at lower temperatures:
– Rinse/ Spin (deactivate = Aqua Plus button) or
select > Drain.
– Press $ Start/Reload.
Individual settings
ʑ Signal
delay the start of the programme before it begins. The Ready in- time can be set in
increments of one hour up to a maximum of 24 hours. Press the Ready in button
repeatedly until the required number of hours is displayed (h = hour). Choose $ Start/
Reload. It is not possible to make adjustments once the programme has started.
Interrupting the programme
3
Ready in
1
... $ Start/Reload flashes and -0- appears on the display
panel.
ce
Spin
speed*
ʑ
ʑ
End of programme when ...
ev
i
LF Cottons
Additional
functions
**If the ' symbol flashes in the
display panel, the childproof lock
is active a deactivate, page 5.
w
.d
Programmes
Detailed overview of programmes a page 7.
Spin speed can be selected individually, irrespective of the
selected programme and programme progress.
Protection of the environment/Conservation tips
– Always fill the washing machine with a maximum amount of
laundry for the relevant programme.
– Wash normally soiled laundry without a pre-wash.
– Instead of LF Cottons 90 °C, choose the programme
LF Cottons 60 °C with the additional function Ĉ EcoPerfect.
Comparable cleaning result with significantly lower energy
consumption.
– Measure the detergent according to the manufacturer's
instructions and water hardness.
– If the laundry is then dried in the tumble dryer, select the spin
speed according to the instructions of the dryer manufacturer.
Setting** and adjusting programmes
(*depending on the model)
m
Compartment I: Detergent for pre-wash
w
w
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
Page
Intended use .......................................................................................1
Programmes ........................................................................................1
Setting and adjusting the programme ...........................................3
Washing ...........................................................................................3/4
After washing ......................................................................................4
Individual settings ..........................................................................5/6
Important information ....................................................................... 6
Overview of programmes ................................................................7
Safety instructions .............................................................................8
Consumption values .........................................................................8
Care .....................................................................................................9
Information on the display panel ....................................................9
Maintenance .................................................................................... 10
What to do if... .................................................................................. 11
Dilute viscous fabric softener and fabric conditioner with water.
This prevents blockages.
an
Contents
ʑ
ua
Compartment II: Detergent for the main wash, water softener, bleach, stain remover
Individual settings
in options button
ʑ Ready
When you select the programme, the relevant programme duration is displayed. You can
Turn the programme selector to Off.
ls
All packaging must be disposed of in accordance with
environmental guidelines.
This appliance is certified in accordance with European Directive
2002/96/EEC on waste electrical and electronic equipment
(WEEE).
This directive provides the framework for the EU-wide collection and
reuse of used appliances.
– Do not leave children unattended near the
washing machine.
– The washing machine is not to be used by
children or persons not familiar with the
operating instructions.
– Keep pets away from the washing machine.
Removing the washing
u
Congratulations ä You have opted for a modern, high-quality
domestic appliance manufactured by Bosch. This washing machine
is distinguished by its economical water and energy consumption.
Each machine that leaves our factory has been inspected thoroughly
to ensure that it functions properly and is in perfect condition.
Washing
Before washing for the first time
Wash once without any laundry a page 9.
.e
Intended use
Your washing machine
4
5
6
@ SuperQuick 15’
30 °C
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II:
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of water
hardness)
Set the programme selector to I Easy-Care 60 °C and select $ Start/Reload. At the end of the programme, turn
the programme selector to Off.
Turn the programme selector to Off and disconnect the mains plug.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Cleaning the detergent drawer ...
Risk of explosion
– Items of laundry pretreated with cleaning agents containing
solvents, e.g. stain remover / cleaning solvent may lead to an
explosion after being loaded into the washing machine.
Rinse items of laundry thoroughly by hand beforehand.
Additional
function
Electricity conWater***
sumption***
Load
7 kg
0,55 kWh
60 l
2:36 h
LF Cottons 40 °C**
7 kg
0,69 kWh
60 l
2:36 h
LF Cottons 60 °C**
7 kg
1,33 kWh
60 l
2:39 h
Ĉ EcoPerfect*
Descaling
Programme
duration***
7 kg
1,05 kWh
47 l
3:08 h
LF Cottons 90 °C
7 kg
2,00 kWh
64 l
2:47 h
I Easy-Care 40 °C**
3 kg
0,55 kWh
55 l
1:37 h
/ Mixed Load 40 °C**
3 kg
0,48 kWh
32 l
1:03 h
“ Delicate/Silk 30 °C
2 kg
0,21 kWh
31 l
0:41 h
: Wool cold
2 kg
0,10 kWh
39 l
0:40 h
: Wool 30 °C
2 kg
0,19 kWh
39 l
0:40 h
.e
ls
ua
an
Ensure there is no laundry in the machine
Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the
correct dosage of detergent is used.
Emergency release, e.g. in the event of a power cut
Drainage hose at the siphon
Turn the programme selector to Off and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Filter in the water supply
Risk of electric shock!
Do not immerse the HydroSafe safety device in water (contains an electric valve).
The programme continues to run when the power has been restored. However, if the laundry has to be removed, the
washing machine door can be opened as follows:
Risk of scalding.
The detergent solution and laundry may be hot. If possible, leave it to cool down.
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen through the glass.
1. Turn the programme selector to Off and disconnect the mains plug.
2. Drain the detergent solution a page 10.
3. Pull the emergency release downwards with a tool and release.
Washing machine door can then be opened.
* Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC.
** Programme setting for testing in accordance with valid standard EN60456.
Note on comparative tests: Try out the test programme by washing the specified load using the maximum spin speed.
As a short programme for coloureds, select the programme / Mixed Load 40 °C with the maximum spin speed.
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
8
Information on the display panel
F: 16
F: 17
F: 18
F: 21
F: 23
ʑ
ʑ
ʑ
ʑ
ʑ
To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into
compartment II and start the > Drain programme.
m
Drum
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
LF Cottons 30 °C**
LF Cottons 60 °C
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
Leave the detergent drawer open so that any residual water can evaporate.
Consumption values
Programme
Pull out, press insert down, remove draw completely.
To remove the insert: press the insert upwards from below with your finger.
Clean the detergent dispenser tray and insert with water and a brush and dry it.
Attach the insert and engage (connect the cylinder to the guide pin).
Push in the detergent drawer.
ce
The washing machine door can become very hot.
Be careful when draining hot detergent solution.
Do not climb onto the washing machine.
Do not lean on the open washing machine door.
Do not reach into the drum if it is still rotating.
Be careful when opening the detergent drawer while the machine
is in operation.
ʑ
ʑ
ʑ
ʑ
ʑ
2* For models without a drainage hose: Carefully unscrew the pump cover until the
detergent solution begins to flow out. When the service flap is half full, close the pump cover
and empty the service flap. Repeat the above steps until all the detergent solution has
completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
ev
i
–
–
–
–
–
–
Wipe with a soft, damp cloth.
Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Remove detergent and cleaning agent residue immediately.
Do not clean with a jet of water.
... if it contains detergent or fabric softener residues.
1.
2.
3.
4.
5.
ʑ
ʑ
2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
Machine housing, control panel
–
–
–
–
What to do if ...
1. Open and remove the service flap.
w
.d
*619963*
Before washing for the first time
– Risk of scalding.
Allow the detergent solution to cool down.
– Turn off the tap.
u
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Maintenance
w
w
Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München / Deutschland
WAE24367GB ...
Risk of electric shock
Risk of injury
7
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
Care
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
1210 / 9000619963
2 kg
cold, 30 °C
: Wool
“cDelicate/Silk
30 °C
3 kg
40 °C
/ Mixed Load
30, 40, 60 °C
I Easy-Care
Additional
2 Rinse/ Spin, > Drain
programmes
* Reduced load for additional ĉ SpeedPerfect function
‘ As a short programme, / Mixed Load 40 °C, with a maximum spin speed, is ideal.
Programmes without pre-wash - add detergent to compartment II, programmes with pre-wash - distribute the detergent between compartments I and II.
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
= Aqua Plus
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
Fabrics made of cotton or easy-care fabrics
= Aqua Plus;
different types of laundry can be washed together
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
For delicate, washable fabrics, e.g. made of silk, satin,
= Aqua Plus;
synthetic fibres or blended fabrics (e.g. curtains)
No spin between rinse cycles
Particularly gentle wash programme to avoid shrinkage of launHandä or machine-washable fabrics made of wool or
dry, longer programme breaks (fabrics rest in the detergent solucontaining wool
tion)
Easy-care fabrics made of cotton, linen, synthetic
Short programme, approx. 15 minutes,
fibres or blended fabrics
suitable for lightly soiled laundry
Easy-care fabrics made of cotton, linen, synthetic
fibres or blended fabrics
ĉ SpeedPerfect*, Ĉ EcoPerfect, S Reduced Ironing,
= Aqua Plus
Hard-wearing fabrics, heat-resistant fabrics made of
cotton or linen
LF Cottons
+ Prewash
30, 40, 60, 90 °C
40 °C
7 kg/
4 kg*
Additional functions; information
Type of laundry
max.
°C
Programmes
a Refer to the table of consumption values on page 8 and notes on page 6.
Overview of programmes
Safety instructions
depending on model
Close the washing machine door properly; laundry may be caught.
Open the tap completely, supply hose kinked or trapped;
Clean the filter a page 10, Water pressure too low.
Detergent solution pump blocked; Clean the detergent solution pump a page 10. Drainage hose / waste pipe
blocked; Clean the drainage hose at the siphon a page 10.
Motor fault. Call customer services.
Water in the base tub, appliance leaking. Call customer services.
9
1.
2.
3.
4.
ʑ
Reduce the water pressure in the supply hose:
Turn off the tap.
Select any programme (except for 2 Rinse/ Spin // > Drain).
Choose $ Start/Reload. Let the programme run for approximately 40 seconds.
Turn the programme selector to Off. Disconnect the mains plug.
Clean the filter:
ʑ
ʑ
ʑ
1. Depending on model:
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and Aqua-Secure models:
ʑ
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
10
Water is leaking out.
–
–
No water supply.
–
Detergent not
–
dispensed.
–
–
Washing machine door –
cannot be opened.
–
–
Programme does not –
start.
–
–
Detergent solution is
–
not drained.
–
–
Water not visible in the –
drum.
Unsatisfactory spin
–
result.
Laundry wet/too damp.
–
–
The programme
–
duration changes
during the wash cycle.
Spin cycle performed –
several times.
Residual water in the –
compartment for care –
products.
Odour formation in the –
washing machine.
Status display³1
–
flashes. Foam may be
coming out of the
detergent drawer.
–
Intense noise
–
formation, vibrations
and “wandering”
–
during the spin cycle.
Noises during spin and –
drain cycles.
Display panel/indicator
lamps do not function
during operation.
Programme sequence
longer than usual.
Attach/replace the drainage hose correctly.
Tighten the screw connection of the supply hose.
$ Start/Reload not selected?
Tap not turned on?
Filter blocked? Clean the filter a page 10.
Supply hose kinked or trapped?
Safety function active. Programme stopped? a page 4.
Is Rinse Hold (without final spin) selected? a page 3, 4.
Can be opened by emergency release only? a page 9.
$ Start/Reload or Ready in time selected?
Washing machine door closed?
Childproof lock active? Deactivate a page 5.
Is Rinse Hold (without final spin) selected? a page 3, 4.
Clean the detergent solution pump a page 10.
Clean the waste pipe and/or drainage hose.
Not a fault - water below the visible area.
Not a fault - the unbalanced-load detection system has cancelled the
spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
SReduced Ironing selected? a page 5.
Selected speed too low? a page 5.
Not a fault – the programme sequence is optimised for the particular
wash process. This may result in changes to the programme duration
in the display field.
Not a fault - unbalanced load detection system adjusts the
imbalance.
Not a fault - the action of the care product is not affected.
Clean the insert if necessary a page 9.
Run programme LF Cottons 90 °C without laundry. Use standard
detergent.
Too much detergent used? Mix 1 tablespoon of fabric softener with
½ litre of water and pour into dispenser II (not for outdoor and downfilled textiles!).
Reduce the detergent dosage for the next wash cycle.
Are the appliance feet fixed?
Secure the appliance feet a Installation instructions.
Transportation safety devices removed? Remove the transportation
safety devices a Installation instructions.
Clean detergent-solution pump a page 10
Power cut?
Fuses triggered? Reset/change the fuse.
If the fault occurs repeatedly, call customer services.
Not a fault - unbalanced load detection system adjusts imbalance by
repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
Detergent residues
– Occasionally, phosphate-free detergents contain water-insoluble
on the laundry.
residues.
– Select the 2 Rinse/ Spin cycle or brush out the laundry after
washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call customer services a Installation instructions.
11
Washing machine
Instruction manual
–
–
–
–
Observe the safety instructions on page 8.
Read these instructions and the separate installation instructions before
operating the washing machine.
en
Intended use
Your washing machine
Preparation
Congratulations ä You have opted for a modern, high-quality
domestic appliance manufactured by Bosch. This washing machine
is distinguished by its economical water and energy consumption.
Each machine that leaves our factory has been inspected thoroughly
to ensure that it functions properly and is in perfect condition.
ʋ for domestic use only,
ʋ for washing machine-washable fabrics and hand-washable wool in detergent solution,
ʋ to be operated with cold drinking water and commercially available detergents and care products which are
suitable for use in washing machines.
Further information: www.bosch-home.com
.
Environmentally friendly waste disposal
– Do not leave children unattended near the
washing machine.
– The washing machine is not to be used by
children or persons not familiar with the
operating instructions.
– Keep pets away from the washing machine.
Checking the machine
– Never use a damaged machine.
– Inform customer service.
Connecting the mains plug
Make sure your hands are dry.
Take hold of the plug only.
Turning the tap on
Po
ua
ls
.e
u
All packaging must be disposed of in accordance with
environmental guidelines.
This appliance is certified in accordance with European Directive
2002/96/EEC on waste electrical and electronic equipment
(WEEE).
This directive provides the framework for the EU-wide collection and
reuse of used appliances.
Correct installation according to the
separate Installation instructions.
Compartment II
II: Detergent for the main wash, water softener, bleach, stain remover
LF Cottons
Compartment I: Detergent for pre-wash
(*depending on the model)
Additional
functions
Spin
speed*
Display panel/
Options button
Start/
Reload
P
Hard-wearing fabrics
+ Prewash
Hard-wearing fabrics, pre-wash at
30 °C
/ Mixed Load
Different types of laundry
@ SuperQuick 15’
Short programme
2 Rinse/
Rinse/ Spin
Laundry washed by hand,
= Aqua Plus button activated; if only
using the spin cycle, deactivate the
button
> Drain
Drain rinsing water for Rinse Hold
(without final spin)
ÿ Wool
Hand/machine-washable wool
“ Delicate/Silk
Delicate washable fabrics
I Easy-Care
Easy-care fabrics
Protection of the environment/Conservation tips
– Always fill the washing machine with a maximum amount of
laundry for the relevant programme.
– Wash normally soiled laundry without a pre-wash.
– Instead of LF Cottons 90 °C, choose the programme
LF Cottons 60 °C with the additional function Ĉ EcoPerfect.
Comparable cleaning result with significantly lower energy
consumption.
– Measure the detergent according to the manufacturer's
instructions and water hardness.
– If the laundry is then dried in the tumble dryer, select the spin
speed according to the instructions of the dryer manufacturer.
Compartment 0: Fabric softener, starch
m
ev
i
ce
Programmes
Detailed overview of programmes a page 7.
Spin speed can be selected individually, irrespective of the
selected programme and programme progress.
w
.d
Page
Intended use .......................................................................................1
Programmes ........................................................................................1
Setting and adjusting the programme ...........................................3
Washing ...........................................................................................3/4
After washing ......................................................................................4
Individual settings ..........................................................................5/6
Important information ....................................................................... 6
Overview of programmes ................................................................7
Safety instructions .............................................................................8
Consumption values .........................................................................8
Care .....................................................................................................9
Information on the display panel ....................................................9
Maintenance .................................................................................... 10
What to do if... .................................................................................. 11
w
w
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
an
Contents
Programme sequence
ü'ü1üü2üü
1 - 24h
Childproof lock, washin
Programme end after
Ready in
1
2
Washing
Before washing for the first time
Wash once without any laundry a page 9.
Removing the washing
Open the washing machine door and remove the washing.
If Rinse Hold (without final spin) is active: Turn the
programme selector to > Drain or select the spin speed.
Press $ Start/Reload.
Sorting and loading laundry
Follow the manufacturer's care information.
According to the information on the care labels.
According to type, colour, soiling and temperature.
Do not exceed the maximum load a page 7.
Observe the important information a page 6.
Insert large and small items of laundry.
Close the washing machine door. Take care not to trap items of laundry
between the washing machine door and the rubber seal.
– Remove any foreign objects - risk of rusting.
– Leave the washing machine door and detergent
drawer open so that any residual water can
evaporate.
Detergent drawer with
compartments I, II, ~
Drum
Turning the tap off
Control panel
Add detergent and care products
Not required for Aqua-Stop models a Refer to installation
instructions.
Washing machine
door
u
Measure accordingly:
Amount of laundry, soiling, water hardness (ask your water supply
company) and manufacturer's instructions.
our liquid detergent into the appropriate dispenser and place in the drum.
.e
Switching off
ua
ls
Turn the programme selector to Off.
Additional functions, the options
button and spin speeds a
Individual settings, page 5.
$ Start/Reload
displays:
ng, rinsing, spinning
m
ce
End of programme when ...
... $ Start/Reload flashes and -0- appears on the display
panel.
Interrupting the programme
3
w
w
All buttons are sensitive and need
only to be touched lightly. Press
and hold the options and spin
speed buttons to run through the
setting options automatically.
1
ev
i
Programme selector
**If the ' symbol flashes in the
display panel, the childproof lock
is active a deactivate, page 5.
w
.d
Setting** and adjusting programmes
an
Dilute viscous fabric softener and fabric conditioner with water.
This prevents blockages.
Service flap
2
Programmes at high temperatures:
– Cool washing: Select Rinse/ Spin.
– Press $ Start/Reload.
Programmes at lower temperatures:
– Rinse/ Spin (deactivate = Aqua Plus button) or
select > Drain.
– Press $ Start/Reload.
Changing the programme, if ...
... you have selected the wrong programme by mistake:
– Reselect the programme.
– Press $ Start/Reload. The new programme starts from
the beginning.
Programme selector for
switching the machine on
and off and for selecting
the programme. Can be
turned in either direction.
Washing
Reloading laundry, if ... a page 5
... $ Start/Reload selected and then YES is lit in the
display panel. If NO is lit, the washing machine door
cannot be opened.
– Press $ Start/Reload.
3
4
Individual settings
in options button
ʑ Ready
When you select the programme, the relevant programme duration is displayed. You can
Individual settings
ʑ Signal
+ 1 step, release
2. Setting the volume
for ...
Childproof lock and reloading
'
Childproof lock/
Appliance lock
You can lock the washing machine to prevent the functions you have
set from being changed inadvertently.
ON /OFF: Press and hold the $ Start/Reload button for approx. 5
seconds after the start/end of the programme.
Note: The childproof lock can remain activated until you wish to start
the next programme, even after switching off the machine.
Then you can deactivate the childproof lock before the start of the
programme and activate it again as necessary once the programme
has started.
If you want to add additional items of laundry after the programme has
started, choose $ Start/Reload.. The machine checks whether
reloading is possible.
YES is lit: Reloading is possible.
NO flashes: wait until YES lights up.
Note: do not open the door until YES is lit.
NO: It is not possible to reload.
Note: For safety reasons, the washing machine door remains locked
when the water level and/or temperature is high, or during spinning.
To continue the programme, press the $ Start/Reload.
w
.d
w
w
$ Start/Reload
To start the programme or to subsequently load additional laundry, and to activate/deactivate
the childproof lock.
u
direct
1 step
Setting the
volume*
Set to •
ls
* you may need to select Setting the
the function several times. volume*
ua
Important information
Protecting the laundry and the machine
– When determining the dosage of all washing powders, additives and cleaning agents, you
must follow the manufacturer's instructions.
– Empty pockets.
– Look out for metal items (paperclips, etc.).
– Wash delicates in a laundry bag (tights, curtains, underwired bras).
– Fasten zips, do up any buttons.
– Brush sand out of pockets and collars.
– Remove curtain fittings or place in the laundry bag.
an
For washing in a shorter time with a washing outcome comparable to
that of the standard programme. Maximum load a Overview of
programmes, page 7.
Ĉ EcoPerfect
For saving energy with a washing performance comparable to that of
the standard programme.
S Reduced Ironing Special spin sequence with subsequent fluffing. More gentle final spin
- residual moisture in the laundry slightly increased.
= Aqua Plus
Increased water level and additional rinse cycle, extended washing
time. For areas with very soft water or for further enhancing the spin
result.
.e
ĉ SpeedPerfect
YES
Reload
ʑ
Button signals
press and hold
1 step, the
display panel
lights up
Information signals
Additional functions a and overview of programmes, see page 7
ev
i
ʑ
Before and while the selected programme is running, you can set the spin speed or Rinse
Hold (without final spin, laundry soaks in the last rinsing water, display - - -). The effects
depend on the programme progress. The maximum selectable spin speed depends on the
model and on which programme is currently selected.
m
ʑ
Set to •
Spin c/ without final spin
ce
ʑ
1200
1000
800
600
Rinse Hold
1. Activating the mode
for setting the signal
volume
delay the start of the programme before it begins. The Ready in- time can be set in
increments of one hour up to a maximum of 24 hours. Press the Ready in button
repeatedly until the required number of hours is displayed (h = hour). Choose $ Start/
Reload. It is not possible to make adjustments once the programme has started.
Laundry with varying degrees of soiling
Wash new items of clothing separately.
Do not pre-wash. If required, choose the additional function
ĉ SpeedPerfect.
Pre-treat any stains as necessary.
intense
Do not load as much laundry.
Choose a programme with pre-wash.
Soaking Load laundry of the same colour
Pour soaking agent/detergent into compartment II in accordance with the manufacturer's
instructions. Turn the programme selector to LF Cottons 30 °C and press $ Start/Reload.
After approx. 10 minutes, press $ Start/Reload to pause the programme. Once the required
soaking time has elapsed, press $ Start/Reload again to continue the programme, or select
a different programme.
Starching Laundry must not be treated with fabric softener
light
Starching is possible in all wash programmes if liquid starch is used. Pour the starch in
accordance with the manufacturer's instructions into fabric softener compartment ~ (rinse first
if necessary).
Dyeing/Bleaching
Dye should only be used in normal household quantities. Salt may damage stainless steel.
Always follow the dye manufacturer's instructions! Do not use the washing machine for
bleaching clothes!
5
6
Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München / Deutschland
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
u
WAE24367GB ...
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
– Keep detergents and care products out of the reach of children.
.e
Risk of poisoning
ua
ls
Risk of explosion
ev
*619963*
ic
em
an
Risk of injury
– Items of laundry pretreated with cleaning agents containing
solvents, e.g. stain remover / cleaning solvent may lead to an
explosion after being loaded into the washing machine.
Rinse items of laundry thoroughly by hand beforehand.
–
–
–
–
–
–
The washing machine door can become very hot.
Be careful when draining hot detergent solution.
Do not climb onto the washing machine.
Do not lean on the open washing machine door.
Do not reach into the drum if it is still rotating.
Be careful when opening the detergent drawer while the machine
is in operation.
1210 / 9000619963
Consumption values
Programme
w
.d
w
w
@ SuperQuick 15’
30 °C
2 kg
cold, 30 °C
: Wool
“cDelicate/Silk
30 °C
3 kg
40 °C
/ Mixed Load
30, 40, 60 °C
I Easy-Care
Additional
2 Rinse/ Spin, > Drain
programmes
* Reduced load for additional ĉ SpeedPerfect function
‘ As a short programme, / Mixed Load 40 °C, with a maximum spin speed, is ideal.
compartment II, programmes with pre-wash - distribute the detergent between compartments I and II.
Programmes without pre-wash - add detergent to compa
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
= Aqua Plus
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
Fabrics made of cotton or easy-care fabrics
= Aqua Plus;
different types of laundry can be washed together
ĉ SpeedPerfect, Ĉ EcoPerfect, S Reduced Ironing,
For delicate, washable fabrics, e.g. made of silk, satin,
= Aqua Plus;
synthetic fibres or blended fabrics (e.g. curtains)
No spin between rinse cycles
Particularly gentle wash programme to avoid shrinkage of launHandä or machine-washable fabrics made of wool or
dry, longer programme breaks (fabrics rest in the detergent solucontaining wool
tion)
Easy-care fabrics made of cotton, linen, synthetic
Short programme, approx. 15 minutes,
fibres or blended fabrics
suitable for lightly soiled laundry
Easy-care fabrics made of cotton, linen, synthetic
fibres or blended fabrics
ĉ SpeedPerfect*, Ĉ EcoPerfect, S Reduced Ironing,
= Aqua Plus
Hard-wearing fabrics, heat-resistant fabrics made of
cotton or linen
LF Cottons
+ Prewash
30, 40, 60, 90 °C
40 °C
7 kg/
4 kg*
Additional functions; information
Type of laundry
max.
°C
Programmes
a Refer to the table of consumption values on page 8 and notes on page 6.
Overview of programmes
Safety instructions
Additional
function
Electricity con- Water***
sumption***
Load
Programme
duration***
LF Cottons 30 °C**
7 kg
0,55 kWh
60 l
2:36 h
LF Cottons 40 °C**
7 kg
0,69 kWh
60 l
2:36 h
LF Cottons 60 °C**
7 kg
1,33 kWh
60 l
2:39 h
7 kg
1,05 kWh
47 l
3:08 h
LF Cottons 90 °C
7 kg
2,00 kWh
64 l
2:47 h
I Easy-Care 40 °C**
3 kg
0,55 kWh
55 l
1:37 h
/ Mixed Load 40 °C**
3 kg
0,48 kWh
32 l
1:03 h
“ Delicate/Silk 30 °C
2 kg
0,21 kWh
31 l
0:41 h
: Wool cold
2 kg
0,10 kWh
39 l
0:40 h
: Wool 30 °C
2 kg
0,19 kWh
39 l
0:40 h
LF Cottons 60 °C
Ĉ EcoPerfect*
* Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC.
** Programme setting for testing in accordance with valid standard EN60456.
Note on comparative tests: Try out the test programme by washing the specified load using the maximum spin speed.
As a short programme for coloureds, select the programme / Mixed Load 40 °C with the maximum spin speed.
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
7
8
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
Care
Maintenance
Before washing for the first time
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II:
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of water
hardness)
Set the programme selector to I Easy-Care 60 °C and select $ Start/Reload. At the end of the programme, turn
the programme selector to Off.
Turn the programme selector to Off and disconnect the mains plug.
1. Open and remove the service flap.
2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
Machine housing, control panel
–
–
–
–
Wipe with a soft, damp cloth.
Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Remove detergent and cleaning agent residue immediately.
Do not clean with a jet of water.
2* For models without a drainage hose: Carefully unscrew the pump cover until the
detergent solution begins to flow out. When the service flap is half full, close the pump cover
and empty the service flap. Repeat the above steps until all the detergent solution has
completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
u
Cleaning the detergent drawer ...
.e
... if it contains detergent or fabric softener residues.
ls
Pull out, press insert down, remove draw completely.
To remove the insert: press the insert upwards from below with your finger.
Clean the detergent dispenser tray and insert with water and a brush and dry it.
Attach the insert and engage (connect the cylinder to the guide pin).
Push in the detergent drawer.
ua
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
an
1.
2.
3.
4.
5.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into
compartment II and start the > Drain programme.
m
Leave the detergent drawer open so that any residual water can evaporate.
Ensure there is no laundry in the machine
ev
i
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
ce
Drum
Descaling
Emergency release, e.g. in the event of a power cut
Drainage hose at the siphon
Turn the programme selector to Off and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Filter in the water supply
w
.d
Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the
correct dosage of detergent is used.
Risk of electric shock!
Do not immerse the HydroSafe safety device in water (contains an electric valve).
The programme continues to run when the power has been restored. However, if the laundry has to be removed, the
washing machine door can be opened as follows:
w
w
Risk of scalding.
The detergent solution and laundry may be hot. If possible, leave it to cool down.
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen through the glass.
1. Turn the programme selector to Off and disconnect the mains plug.
2. Drain the detergent solution a page 10.
3. Pull the emergency release downwards with a tool and release.
Washing machine door can then be opened.
Information on the display panel
F: 16
F: 17
F: 18
F: 21
F: 23
– Risk of scalding.
Allow the detergent solution to cool down.
– Turn off the tap.
depending on model
Close the washing machine door properly; laundry may be caught.
Open the tap completely, supply hose kinked or trapped;
Clean the filter a page 10, Water pressure too low.
Detergent solution pump blocked; Clean the detergent solution pump a page 10. Drainage hose / waste pipe
blocked; Clean the drainage hose at the siphon a page 10.
Motor fault. Call customer services.
Water in the base tub, appliance leaking. Call customer services.
9
1.
2.
3.
4.
Reduce the water pressure in the supply hose:
Turn off the tap.
Select any programme (except for 2 Rinse/ Spin // > Drain).
Choose $ Start/Reload. Let the programme run for approximately 40 seconds.
Turn the programme selector to Off. Disconnect the mains plug.
Clean the filter:
1. Depending on model:
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and Aqua-Secure models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
10
What to do if ...
ʑ
ʑ
ʑ
ʑ
ʑ
Display panel/indicator
lamps do not function
during operation.
Programme sequence
longer than usual.
ua
an
Washing machine
ce
m
Not a fault - the unbalanced-load detection system has cancelled the
spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
SReduced Ironing selected? a page 5.
Selected speed too low? a page 5.
Not a fault – the programme sequence is optimised for the particular
wash process. This may result in changes to the programme duration
in the display field.
Not a fault - unbalanced load detection system adjusts the
imbalance.
Not a fault - the action of the care product is not affected.
Clean the insert if necessary a page 9.
ls
.e
u
Attach/replace the drainage hose correctly.
Tighten the screw connection of the supply hose.
$ Start/Reload not selected?
Tap not turned on?
Filter blocked? Clean the filter a page 10.
Supply hose kinked or trapped?
Safety function active. Programme stopped? a page 4.
Is Rinse Hold (without final spin) selected? a page 3, 4.
Can be opened by emergency release only? a page 9.
$ Start/Reload or Ready in time selected?
Washing machine door closed?
Childproof lock active? Deactivate a page 5.
Is Rinse Hold (without final spin) selected? a page 3, 4.
Clean the detergent solution pump a page 10.
Clean the waste pipe and/or drainage hose.
Not a fault - water below the visible area.
ev
i
ʑ
ʑ
ʑ
ʑ
ʑ
–
–
No water supply.
–
Detergent not
–
dispensed.
–
–
Washing machine door –
cannot be opened.
–
–
Programme does not –
start.
–
–
Detergent solution is
–
not drained.
–
–
Water not visible in the –
drum.
Unsatisfactory spin
–
result.
Laundry wet/too damp.
–
–
The programme
–
duration changes
during the wash cycle.
Spin cycle performed –
several times.
Residual water in the –
compartment for care –
products.
Odour formation in the –
washing machine.
Status display³1
–
flashes. Foam may be
coming out of the
detergent drawer.
–
Intense noise
–
formation, vibrations
and “wandering”
–
during the spin cycle.
Noises during spin and –
drain cycles.
Run programme LF Cottons 90 °C without laundry. Use standard
detergent.
Too much detergent used? Mix 1 tablespoon of fabric softener with
½ litre of water and pour into dispenser II (not for outdoor and downfilled textiles!).
Reduce the detergent dosage for the next wash cycle.
Are the appliance feet fixed?
Secure the appliance feet a Installation instructions.
instructions
Transportation safety devices removed? Remove the transportation
instructions.
safety devices a Installation instructions.
Clean detergent-solution pump a page 10
w
.d
ʑ
ʑ
ʑ
ʑ
ʑ
Water is leaking out.
Instruction manual
w
w
ʑ
ʑ
–
–
–
–
Power cut?
Fuses triggered? Reset/change the fuse.
If the fault occurs repeatedly, call customer services.
Not a fault - unbalanced load detection system adjusts imbalance by
repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
Detergent residues
– Occasionally, phosphate-free detergents contain water-insoluble
on the laundry.
residues.
– Select the 2 Rinse/ Spin cycle or brush out the laundry after
washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call customer services a Installation instructions.
11
Observe the safety instructions on page 8.
Read these instructions and the separate installation instructions before
operating the washing machine.
en
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising