PLA 1 - TD Sheet (Articulating Arm)

PLA 1 - TD Sheet (Articulating Arm)
page 1 of 3
TECHNICAL DATA SHEET - Solid•Point Articulating Swivel Plasma Mount
™
MODELS: PLA 1, PLA 1S
The PLA 1 and PLA 1S allows multiple viewing positions within the
same room. When retracted, the screen sits almost flush against the wall,
or the articulating arm can be extended to maximum of 30.5" (775 mm) from
the wall. Three pivot points on the arm with 180 degree swivel create
limitless viewing positions. Multiple attachment points on the wall plate are
provided so the arm can be mounted at the center, or left/right of center on
the wall plate. 18" wall plate mounts to two studs with 16" centers.
Can only be mounted to wood studs, solid concrete, or
cinder block with appropriate fasteners.
Features:
• Articulating arm can be center mounted or at four
other points off center
• Arm extends up to 30.5" (775 mm) away from wall
for perfect viewing
• Three point swivel action
• Adjustable screen tilt with a max. 10° forward, 5°
backward
• Bracket adds approximately 4" (102 mm) to depth of screen
• Wire management contains and protects cords
• Screen mounts vertically or horizontally
• Adjustable roll with a max. 10° left, 10° right to allow for leveling of plasma to
sit level at any position
• Can only be mounted to wood studs, solid concrete, or concrete block with
appropriate fasteners
• Heavy gauge cold rolled steel construction
• Scratch resistant black or silver fused epoxy finish
Dimensions:
Weight:
32.1 lb (14.6 kg)
Shipping weight:
34.9 lb (15.8 kg)
Maximum Load Capacity:
185 lb (84 kg)
Components:
• Wall plate
• Articulating arm
• Wood stud mounting hardware
• PLP adapter plate must be ordered separately
UL listed 150 lb (68 kg)
(4 x UL listed load)
Shipping Carton dimensions:
L= 18.25 in (464 mm)
W= 15.75 in (400 mm)
H= 6.625 in (168 mm)
Accessories:
• Alligator® concrete anchors ACC 204
AR C H I T E C TS S P E C I F I CAT I O N S
The Articulating Swivel Arm shall be a Peerless model PLA 1 and PLA 1S and shall be located where indicated on the plans. It shall be
constructed of heavy gauge cold rolled steel with 0°-10° adjustable forward and 5° backward tilt. The wall plate shall feature five
mounting positions at 3" intervals. The finish shall be scratch resistant Black or Silver Fused Epoxy. Assembly and installation shall be
done according to instructions provided by the manufacturer.
Peerless Industries, Inc.
3215 W. North Ave. Melrose Park, IL 60160
708-865-8870 800-865-2112 Fax 708-865-2941
www.peerlessindustries.com
ISSUED: 06-19-02 SHEET NO: 200-9705-12 06-20-05
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
Solid•Point is a trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
page 2 of 3
TECHNICAL DATA SHEET
MODELS: PLA 1, PLA 1S
A = 1/2 HEIGHT OF PLASMA + 10.75" ± OFFSET*
B = DEPTH OF PLASMA + DEPTH OF ADAPTER BRACKET* + 4.875"
ALL DIMENSIONS = INCH (MM)
*For offset and depth of adapter bracket refer to PLP TD sheet
0o - 10o
TILT
vertical
position
DEPTH
center of
adapter
bracket
horizontal
position
adapter
bracket (not
included)
A
HEIGHT
10.75
(273)
plasma
WIDTH
4.875
(124)
FRONT VIEW
B
18.0
(457)
0.5
(13)
SIDE VIEW
1.0
(25)
9.0
(229)
2.75
(70)
1.54
(39)
4.5
(114)
10.25
(260)
CL
1.39
(35)
16.0
(406)
0.345" (9 mm) x 0.846" (21 mm) SLOT (8 PLCS.)
WALL PLATE DETAIL
Peerless Industries, Inc.
3215 W. North Ave. Melrose Park, IL 60160
708-865-8870 800-865-2112 Fax 708-865-2941
www.peerlessindustries.com
ISSUED: 06-19-02 SHEET NO: 200-9705-12 06-20-05
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
Solid•Point is a trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
page 3 of 3
TECHNICAL DATA SHEET
ALL DIMENSIONS = INCH (MM)
MODELS: PLA 1, PLA 1S
THE MAXIMUM TV WIDTH THAT WOULD ALLOW A MOUNTED PLASMA SCREEN A FULL 180 DEGREE
SWIVEL IS 48.75" (1238 mm)
CL
PLASMA
ADAPTER BRACKET
(NOT INCLUDED)
SWIVEL
POINT
26.75
(679)
X
X = 1/2 width of plasma
TOP VIEW (A)
PLASMA
ADAPTER BRACKET
(NOT INCLUDED)
30.5
(775)
TOP VIEW (B)
Peerless Industries, Inc.
3215 W. North Ave. Melrose Park, IL 60160
708-865-8870 800-865-2112 Fax 708-865-2941
www.peerlessindustries.com
ISSUED: 06-19-02 SHEET NO: 200-9705-12 06-20-05
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
Solid•Point is a trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising