Panasonic PT-L200U Projector User Guide Manual Operating Instruction Pdf

Panasonic PT-L200U Projector User Guide Manual Operating Instruction Pdf
R
LCD Projector
POWER
LIGHT
INPUT
VI D E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
Operating Instructions
VOLUME
MUTE
SD
SD
MENU
TIME
LCD PROJECTOR
Model No.
PT-L300U
PT-L200U
Before operating this product, please read the instructions carefully and save this
manual for future use.
TQBJ 0120-1
This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most performance out
of your new product, and that you will be pleased with your Panasonic LCD
projector.
The serial number of your product may be found on its back. You should
note it in the space provided below and retain this booklet in case service is
required.
Model number: PT-L300U / PT-L200U
Serial number:
IMPORTANT SAFETY NOTICE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION: The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
2
CAUTION: This equipment is equipped with a
three-pin grounding-type power
plug. Do not remove the grounding
pin on the power plug. This plug will
only fit a grounding-type power
outlet. This is a safety feature. If you
are unable to insert the plug into the
outlet, contact an electrician. Do not
defeat the purpose of the grounding
plug.
Preparation
Dear Panasonic Customer:
Do not remove
WARNING:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any unauthorized changes or modifications to this equipment
will void the users authority to operate.
Declaration of Conformity
Model Number:
PT-L300U / PT-L200U
Trade Name:
Panasonic
Responsible party: Matsushita Electric Corporation of America.
Address:
One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-800-528-8601 or 1-800-222-0741
Email:
pbtsservice@panasonic.com
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
3
This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most performance out
of your new product, and that you will be pleased with your Panasonic LCD
projector.
The serial number of your product may be found on its back. You should
note it in the space provided below and retain this booklet in case service is
required.
Model number: PT-L300U / PT-L200U
Serial number:
IMPORTANT SAFETY NOTICE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION: The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
2
CAUTION: This equipment is equipped with a
three-pin grounding-type power
plug. Do not remove the grounding
pin on the power plug. This plug will
only fit a grounding-type power
outlet. This is a safety feature. If you
are unable to insert the plug into the
outlet, contact an electrician. Do not
defeat the purpose of the grounding
plug.
Preparation
Dear Panasonic Customer:
Do not remove
WARNING:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any unauthorized changes or modifications to this equipment
will void the users authority to operate.
Declaration of Conformity
Model Number:
PT-L300U / PT-L200U
Trade Name:
Panasonic
Responsible party: Matsushita Electric Corporation of America.
Address:
One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-800-528-8601 or 1-800-222-0741
Email:
pbtsservice@panasonic.com
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
3
Preparation
IMPORTANT SAFETY NOTICE..........2
Precautions with regard to safety ....5
Accessories........................................9
Precautions on handling .................10
Location and function of each part...12
Using the remote control unit.........17
Inserting the batteries .....................17
Operating range..............................17
Connections .....................................18
Notes on connections .....................18
Example of connecting to video equipment...18
Example of connecting to equipment
compatible with YPBPR(CBCR) signals ...19
Example of connecting to computer ...20
Setting-up .........................................21
Projection methods.........................21
Projector position............................21
Basic Operation
Starting to use..................................22
Turning on the power......................22
Turning off the power......................23
On-screen menus.............................24
Menu screens .................................24
Menu operation guide.....................26
Unavailable on-screen menu items...26
Returning to the previous screen....26
Returning a setting to the factory default ...27
Using the freeze function ................27
Correcting keystone distortion.......28
Setting the ASPECT.........................30
Selecting the picture mode .............32
Using the shutter function ..............33
Changing the display language......33
Muting the sound .............................33
Adjusting the picture .......................34
PICTURE MODE ............................34
CONTRAST....................................34
BRIGHT ..........................................34
COLOR...........................................34
TINT................................................35
SHARPNESS .................................35
TV SYSTEM ...................................35
Color Hue Setting ..........................35
WHITE BALANCE R/G/B ...............36
SIGNAL MODE...............................36
GAMMA ADJUST ..........................36
MEMORY SAVE ............................36
MEMORY LOAD ............................36
Projecting sRGB compatible pictures ...37
4
Precautions with regard to safety
Adjusting the position .....................38
HORIZONTAL POSITION ..............38
VERTICAL POSITION....................38
DOT CLOCK...................................38
CLOCK PHASE ..............................38
ASPECT .........................................39
AUTO SETUP.................................39
Advanced Operation
Option settings.................................39
OSD................................................39
NR (Noise Reduction).....................39
PC PRIORITY.................................39
BACK COLOR ................................39
4:3 H-POS ......................................40
FRONT/REAR ................................40
DESK/CEILING ..............................40
FAN CONTROL..............................40
LAMP POWER ...............................40
LAMP RUNTIME ............................40
SD memory card ..............................41
What is the SD memory card?........41
Data that can be played back .........41
Note when using SD memory cards...41
Inserting and removing the SD
memory card .................................42
About the SD menu..........................43
Playing back still images ................44
Slide playback of still images .........45
Playing back moving images..........49
Error displays...................................50
Others
Indicators..........................................51
Cleaning and replacing
the air filter ....................................53
Replacing the lamp unit ..................54
Before calling for service ................57
Specifications...................................59
Appendix...........................................61
List of compatible signals ...............61
Connector pin wiring.......................62
Projection dimensions calculation methods...63
DCF standard .................................64
Dimensions.......................................65
Trademark acknowledgements ......65
WARNING
Preparation
Contents
If a problem occurs (such as no image or no sound) or if you notice
smoke or a strange smell coming from the projector, turn off the power
and disconnect the power cord from the wall outlet.
B Do not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
B Check that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
B Do not attempt to repair the projector yourself, as this can be dangerous.
Do not look into the lens while the projector is being used.
B Strong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
Be especially careful not to let young children look into the lens.
In addition, turn off the power when you are away from the projector.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
B If the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
B If installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, turn off the power and disconnect the
power cord from the wall outlet.
B Continued use of the projector in this condition may result in fire or electric
shocks.
B Contact an Authorized Service Center for repairs.
Do not overload the wall outlet.
B If the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
B High voltages which can cause fire or electric shocks are present inside
the projector.
B For any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
B If dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord out
from the wall outlet and wipe it with a dry cloth.
5
Preparation
IMPORTANT SAFETY NOTICE..........2
Precautions with regard to safety ....5
Accessories........................................9
Precautions on handling .................10
Location and function of each part...12
Using the remote control unit.........17
Inserting the batteries .....................17
Operating range..............................17
Connections .....................................18
Notes on connections .....................18
Example of connecting to video equipment...18
Example of connecting to equipment
compatible with YPBPR(CBCR) signals ...19
Example of connecting to computer ...20
Setting-up .........................................21
Projection methods.........................21
Projector position............................21
Basic Operation
Starting to use..................................22
Turning on the power......................22
Turning off the power......................23
On-screen menus.............................24
Menu screens .................................24
Menu operation guide.....................26
Unavailable on-screen menu items...26
Returning to the previous screen....26
Returning a setting to the factory default ...27
Using the freeze function ................27
Correcting keystone distortion.......28
Setting the ASPECT.........................30
Selecting the picture mode .............32
Using the shutter function ..............33
Changing the display language......33
Muting the sound .............................33
Adjusting the picture .......................34
PICTURE MODE ............................34
CONTRAST....................................34
BRIGHT ..........................................34
COLOR...........................................34
TINT................................................35
SHARPNESS .................................35
TV SYSTEM ...................................35
Color Hue Setting ..........................35
WHITE BALANCE R/G/B ...............36
SIGNAL MODE...............................36
GAMMA ADJUST ..........................36
MEMORY SAVE ............................36
MEMORY LOAD ............................36
Projecting sRGB compatible pictures ...37
4
Precautions with regard to safety
Adjusting the position .....................38
HORIZONTAL POSITION ..............38
VERTICAL POSITION....................38
DOT CLOCK...................................38
CLOCK PHASE ..............................38
ASPECT .........................................39
AUTO SETUP.................................39
Advanced Operation
Option settings.................................39
OSD................................................39
NR (Noise Reduction).....................39
PC PRIORITY.................................39
BACK COLOR ................................39
4:3 H-POS ......................................40
FRONT/REAR ................................40
DESK/CEILING ..............................40
FAN CONTROL..............................40
LAMP POWER ...............................40
LAMP RUNTIME ............................40
SD memory card ..............................41
What is the SD memory card?........41
Data that can be played back .........41
Note when using SD memory cards...41
Inserting and removing the SD
memory card .................................42
About the SD menu..........................43
Playing back still images ................44
Slide playback of still images .........45
Playing back moving images..........49
Error displays...................................50
Others
Indicators..........................................51
Cleaning and replacing
the air filter ....................................53
Replacing the lamp unit ..................54
Before calling for service ................57
Specifications...................................59
Appendix...........................................61
List of compatible signals ...............61
Connector pin wiring.......................62
Projection dimensions calculation methods...63
DCF standard .................................64
Dimensions.......................................65
Trademark acknowledgements ......65
WARNING
Preparation
Contents
If a problem occurs (such as no image or no sound) or if you notice
smoke or a strange smell coming from the projector, turn off the power
and disconnect the power cord from the wall outlet.
B Do not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
B Check that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
B Do not attempt to repair the projector yourself, as this can be dangerous.
Do not look into the lens while the projector is being used.
B Strong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
Be especially careful not to let young children look into the lens.
In addition, turn off the power when you are away from the projector.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
B If the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
B If installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, turn off the power and disconnect the
power cord from the wall outlet.
B Continued use of the projector in this condition may result in fire or electric
shocks.
B Contact an Authorized Service Center for repairs.
Do not overload the wall outlet.
B If the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
B High voltages which can cause fire or electric shocks are present inside
the projector.
B For any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
B If dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord out
from the wall outlet and wipe it with a dry cloth.
5
6
B Heated air comes out of the air outlet port. Do not bring your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Replacement of the lamp unit should only be carried out by a qualified
technician.
B The lamp unit has high internal pressure. It can easily become damaged if
struck against hard objects or dropped, and injury or malfunctions may
result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
B The lamp cover gets very hot, and contact with it can cause burns.
Before replacing the lamp, be sure to unplug the power cord from the
power outlet.
B Electric shocks or explosions can result if this is not done.
Preparation
B If not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.
Do not do anything that might damage the power cord or the power
cord plug.
B Do not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
B If the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
B Ask an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
B Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
B If the plug is not inserted correctly, electric shocks or overheating could
result.
B Do not use plugs which are damaged or wall outlets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
B If the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
B Failure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
B If water spills onto the projector or gets inside it, fire or electric shocks
could result.
B If any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
B Do not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Do not allow the + and - terminals of the battery to come into contact
with metallic objects such as necklaces or hairpins.
B Failure to observe this may cause the battery to leak, overheat, explode or
catch fire.
B Store the battery in a plastic bag and keep it away from metallic objects.
During a thunderstorm, do not touch the projector or the cable.
B Electric shocks can result.
Do not use the projector in a bath or shower.
B Fire or electric shocks can result.
Do not bring your hands or other objects close to the air outlet port.
Caution
Do not cover the air inlet or the air outlet.
B Doing so may cause the projector to overheat, which can cause fire or
damage to the projector.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
B Using the projector under such conditions may result in fire or electric
shocks.
When disconnecting the power cord, hold the plug, not the cord.
B If the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
B Moving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
B Failure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the battery or place it into
water or fire.
B Failure to observe this may cause the battery to overheat, leak, explode or
catch fire, and burns or other injury may result.
When inserting the battery, make sure the polarities (+ and -) are
correct.
B If the battery is inserted incorrectly, it may explode or leak, and fire, injury
or contamination of the battery compartment and surrounding area may
result.
7
6
B Heated air comes out of the air outlet port. Do not bring your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Replacement of the lamp unit should only be carried out by a qualified
technician.
B The lamp unit has high internal pressure. It can easily become damaged if
struck against hard objects or dropped, and injury or malfunctions may
result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
B The lamp cover gets very hot, and contact with it can cause burns.
Before replacing the lamp, be sure to unplug the power cord from the
power outlet.
B Electric shocks or explosions can result if this is not done.
Preparation
B If not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.
Do not do anything that might damage the power cord or the power
cord plug.
B Do not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
B If the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
B Ask an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
B Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
B If the plug is not inserted correctly, electric shocks or overheating could
result.
B Do not use plugs which are damaged or wall outlets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
B If the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
B Failure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
B If water spills onto the projector or gets inside it, fire or electric shocks
could result.
B If any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
B Do not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Do not allow the + and - terminals of the battery to come into contact
with metallic objects such as necklaces or hairpins.
B Failure to observe this may cause the battery to leak, overheat, explode or
catch fire.
B Store the battery in a plastic bag and keep it away from metallic objects.
During a thunderstorm, do not touch the projector or the cable.
B Electric shocks can result.
Do not use the projector in a bath or shower.
B Fire or electric shocks can result.
Do not bring your hands or other objects close to the air outlet port.
Caution
Do not cover the air inlet or the air outlet.
B Doing so may cause the projector to overheat, which can cause fire or
damage to the projector.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
B Using the projector under such conditions may result in fire or electric
shocks.
When disconnecting the power cord, hold the plug, not the cord.
B If the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
B Moving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
B Failure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the battery or place it into
water or fire.
B Failure to observe this may cause the battery to overheat, leak, explode or
catch fire, and burns or other injury may result.
When inserting the battery, make sure the polarities (+ and -) are
correct.
B If the battery is inserted incorrectly, it may explode or leak, and fire, injury
or contamination of the battery compartment and surrounding area may
result.
7
Accessories
Check that all of the accessories shown below have been included with your
projector.
Remote control unit
(N2QAFA000002 x1)
Video/Audio cable [3.0
m (9´10˝),
K2KA2FA00001 x1]
AAA batteries for
remote control unit (x2)
Power cord
(K2CG3FR00001 x 1)
Carrying bag
(TPEP008 x1)
Preparation
Use only the specified battery.
B If an incorrect battery is used, it may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Do not mix old and new batteries.
B If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Do not put your weight on this projector.
B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children climb onto the equipment.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
B Electric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least
once a year.
B If dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
B It is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
We are in effort to hold your environment clean. Please bring the non
repairable unit your Dealer or a Recycling Company.
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
MENU
TIME
LCD PROJECTOR
NOTICE:
B This product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
8
9
Accessories
Check that all of the accessories shown below have been included with your
projector.
Remote control unit
(N2QAFA000002 x1)
Video/Audio cable [3.0
m (9´10˝),
K2KA2FA00001 x1]
AAA batteries for
remote control unit (x2)
Power cord
(K2CG3FR00001 x 1)
Carrying bag
(TPEP008 x1)
Preparation
Use only the specified battery.
B If an incorrect battery is used, it may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Do not mix old and new batteries.
B If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Do not put your weight on this projector.
B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children climb onto the equipment.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
B Electric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least
once a year.
B If dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
B It is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
We are in effort to hold your environment clean. Please bring the non
repairable unit your Dealer or a Recycling Company.
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
MENU
TIME
LCD PROJECTOR
NOTICE:
B This product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
8
9
Cautions when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.
Cautions regarding setting-up
Observe the following at all times when setting up the projector.
Avoid setting up in places which are subject to vibration or shocks.
If the projector is set up in locations with strong vibration, such as near a
motor, or if it is installed inside a vehicle or on board a ship, the projector
may be subjected to vibration or shocks which can damage the internal parts
and cause malfunctions or accidents. Accordingly, set up the projector in a
place which is free from such vibrations and shocks.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference if it is set up
near high-voltage power lines or motors.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
If the projector is to be suspended from the ceiling, you will need to purchase
the separate installation kit (Model No.: ET-PKE300). Furthermore, all
installation work should only be carried out by a qualified technician.
If using this projector at high elevations (above 1400 m), set the FAN
CONTROL to HIGH. (Refer to page 40.)
Failure to observe this may result in malfunctions.
Notes on use
In order to get the best picture quality
If outside light or light from indoor lamps is shining onto the screen, the
images projected will not have good contrast. Draw curtains or blinds over
any windows and turn off any fluorescent lights near the screen to prevent
reflection.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the accessory lens cover.
10
About the SD memory card slot
Make sure that there are no foreign objects inside the slot when inserting an
optional SD memory card. Failure to observe it may damage the card and
the slot.
About the screen
If the screen you are using is dirty, damaged or discolored, attractive
projections cannot be obtained. Do not apply any volatile substances to the
screen, and do not let it become dirty or damaged.
About the lamp
The lamp may need to be replaced earlier due to variables such as a
particular lamp’s characteristics, usage conditions and the installation
environment, especially when it is subjected to a continuous use for more
than 10 hours.
About the liquid crystal panel
The liquid crystal panel of the projector is built with very high precision
technology giving you fine picture details. Occasionally, a few non-active
pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your LCD.
Before carrying out cleaning and maintenance, be
sure to disconnect the power cord plug from the
wall outlet.
Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water with a small amount
of neutral detergent in it, squeeze the cloth very well, and then wipe the
cabinet. After cleaning, wipe the cabinet dry with a dry cloth.
If using a chemically-treated cloth, read the instructions supplied with
the cloth before use.
Do not wipe the lens with a cloth that is dusty or which produces lint.
If any dust or lint gets onto the lens, such dust or lint will be magnified and
projected onto the screen. Use a blower to clean any dust and lint from the
lens surface, or use a soft cloth to wipe off any dust or lint.
11
Preparation
Precautions on handling
Cautions when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.
Cautions regarding setting-up
Observe the following at all times when setting up the projector.
Avoid setting up in places which are subject to vibration or shocks.
If the projector is set up in locations with strong vibration, such as near a
motor, or if it is installed inside a vehicle or on board a ship, the projector
may be subjected to vibration or shocks which can damage the internal parts
and cause malfunctions or accidents. Accordingly, set up the projector in a
place which is free from such vibrations and shocks.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference if it is set up
near high-voltage power lines or motors.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
If the projector is to be suspended from the ceiling, you will need to purchase
the separate installation kit (Model No.: ET-PKE300). Furthermore, all
installation work should only be carried out by a qualified technician.
If using this projector at high elevations (above 1400 m), set the FAN
CONTROL to HIGH. (Refer to page 40.)
Failure to observe this may result in malfunctions.
Notes on use
In order to get the best picture quality
If outside light or light from indoor lamps is shining onto the screen, the
images projected will not have good contrast. Draw curtains or blinds over
any windows and turn off any fluorescent lights near the screen to prevent
reflection.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the accessory lens cover.
10
About the SD memory card slot
Make sure that there are no foreign objects inside the slot when inserting an
optional SD memory card. Failure to observe it may damage the card and
the slot.
About the screen
If the screen you are using is dirty, damaged or discolored, attractive
projections cannot be obtained. Do not apply any volatile substances to the
screen, and do not let it become dirty or damaged.
About the lamp
The lamp may need to be replaced earlier due to variables such as a
particular lamp’s characteristics, usage conditions and the installation
environment, especially when it is subjected to a continuous use for more
than 10 hours.
About the liquid crystal panel
The liquid crystal panel of the projector is built with very high precision
technology giving you fine picture details. Occasionally, a few non-active
pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your LCD.
Before carrying out cleaning and maintenance, be
sure to disconnect the power cord plug from the
wall outlet.
Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water with a small amount
of neutral detergent in it, squeeze the cloth very well, and then wipe the
cabinet. After cleaning, wipe the cabinet dry with a dry cloth.
If using a chemically-treated cloth, read the instructions supplied with
the cloth before use.
Do not wipe the lens with a cloth that is dusty or which produces lint.
If any dust or lint gets onto the lens, such dust or lint will be magnified and
projected onto the screen. Use a blower to clean any dust and lint from the
lens surface, or use a soft cloth to wipe off any dust or lint.
11
Preparation
Precautions on handling
Projector <Top, right and front>
&%$ #
0
Preparation
Location and function of each part
Projector <Back and bottom>
/.
$
#
'
'
'
,
+
(
%
&
)
*
# Speaker
$ Zoom ring
(page 23)
% Focus ring
(page 23)
& Projection lens
' Air inlet ports
Do not cover this port.
( Front adjustable legs(L/R)
(page 22)
) Lens cover
* Leg adjuster buttons(L/R)
(page 22)
This button is used to unlock the
front adjustable legs. Press to
adjust the angle of tilt of the
projector.
+ Air filter
(page 53)
, Remote control signal receptor
(page 17)
12
- MAIN POWER switch
(pages 22 and 23)
. SD memory card slot
(page 42)
Insert the SD memory card into
here after opening the cover.
/ Access lamp
(page 42)
Flashes while the projector is
being accessed for reading or
writing the data in the SD
memory card.
0 Projector control panel
(page 14)
# Air outlet port
Do not cover this port.
WARNING
Do not bring your hands or other
objects close to the air outlet
port.
B Heated air comes out of the air
outlet port. Do not bring your
hands or face, or objects which
cannot withstand heat close to
this port, otherwise burns or
damage could result.
$ Connector panel
(page 16)
% Power input socket (AC IN)
(page 22)
The accessory power cord is
connected here.
Do not use any power cord other
than the accessory power cord.
& Lamp unit holder
(page 55)
NOTE:
B During projection of an image, the
cooling fan will operate, emitting
a small noise as it operates.
Turning the lamp on or off will
cause this noise to increase a
little.
B By using the OPTION menu to
set “LAMP POWER” to LOW, the
operating sound of the fan can be
reduced. (Refer to page 40.)
' Security lock
This can be used to connect a
commercially-available theftprevention cable (manufactured
by Kensington). This security lock
is compatible with the Microsaver
Security System from
Kensington. Contact details for
this company are given below.
Kensington Technology Group
ACCO Brands Inc.
2855 Campus Drive
San Mateo, CA 94403 USA
Tel (650)572-2700
Fax (650)572-9675
http://www.kensington.com/
http://www.gravis.com/
13
Projector <Top, right and front>
&%$ #
0
Preparation
Location and function of each part
Projector <Back and bottom>
/.
$
#
'
'
'
,
+
(
%
&
)
*
# Speaker
$ Zoom ring
(page 23)
% Focus ring
(page 23)
& Projection lens
' Air inlet ports
Do not cover this port.
( Front adjustable legs(L/R)
(page 22)
) Lens cover
* Leg adjuster buttons(L/R)
(page 22)
This button is used to unlock the
front adjustable legs. Press to
adjust the angle of tilt of the
projector.
+ Air filter
(page 53)
, Remote control signal receptor
(page 17)
12
- MAIN POWER switch
(pages 22 and 23)
. SD memory card slot
(page 42)
Insert the SD memory card into
here after opening the cover.
/ Access lamp
(page 42)
Flashes while the projector is
being accessed for reading or
writing the data in the SD
memory card.
0 Projector control panel
(page 14)
# Air outlet port
Do not cover this port.
WARNING
Do not bring your hands or other
objects close to the air outlet
port.
B Heated air comes out of the air
outlet port. Do not bring your
hands or face, or objects which
cannot withstand heat close to
this port, otherwise burns or
damage could result.
$ Connector panel
(page 16)
% Power input socket (AC IN)
(page 22)
The accessory power cord is
connected here.
Do not use any power cord other
than the accessory power cord.
& Lamp unit holder
(page 55)
NOTE:
B During projection of an image, the
cooling fan will operate, emitting
a small noise as it operates.
Turning the lamp on or off will
cause this noise to increase a
little.
B By using the OPTION menu to
set “LAMP POWER” to LOW, the
operating sound of the fan can be
reduced. (Refer to page 40.)
' Security lock
This can be used to connect a
commercially-available theftprevention cable (manufactured
by Kensington). This security lock
is compatible with the Microsaver
Security System from
Kensington. Contact details for
this company are given below.
Kensington Technology Group
ACCO Brands Inc.
2855 Campus Drive
San Mateo, CA 94403 USA
Tel (650)572-2700
Fax (650)572-9675
http://www.kensington.com/
http://www.gravis.com/
13
'
(
)
/
POWER
&
LIGHT
INPUT
VID E O
'
(
)
,
.
#
$
CMPNT
PC
COMPONENT
KEYSTONE
MENU
&
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
*
+
+
ENTER
SD
%
*
MENU
0
1
2
3
TIME
LCD PROJECTOR
456
B The remote control unit and the projector itself have the same control
buttons available.
# TEMP indicator
(page 51)
This indicator illuminates if an
abnormally high temperature is
detected inside the projector. If
the temperature rises above a
certain level, the power supply
will be turned off automatically
and the indicator will illuminate or
flash.
$ LAMP indicator
(page 52)
This indicator illuminates when it
is time to replace the lamp unit. It
flashes if a circuit abnormality is
detected.
% Power indicator
(pages 22 and 23)
This indicator illuminates red
when the main power is switched
on (Standby Mode), and it
illuminates green when projection
of an image begins.
14
& POWER button
(pages 22 and 23)
' MENU button
(page 24)
This button is used to display
menu screens. When a menu
screen is being displayed, it can
be used to return to a previous
screen or to clear the screen.
F, G, I and H)
( Arrow (F
buttons
(page 26)
These buttons are used to select
and adjust items in the on-screen
menu screens.
) ENTER button
(page 26)
This button is used to accept and
to activate items selected in the
on-screen menus.
* Input select button
(INPUT/VIDEO/COMPONENT/
PC button) (page 22)
+ KEYSTONE buttons
(pages 28 and 29)
This button is used to correct
keystone distortion of the
projected image when the
projector position is tilted upward
or downward.
, NORMAL button
(page 27)
This button is used to reset the
projector adjustment values to the
factory default settings.
- ASPECT button
(page 30)
This button is used for aspect
adjustment (vertical and
horizontal proportions).
. MUTE button
(page 33)
This button momentarily stops
output of the projector’s built-in
speaker.
/ LIGHT button
This button is used to illuminate
the buttons on the remote control
unit.
0 FREEZE button
(page 36)
This button is used to
momentarily freeze projection so
that a still picture is displayed.
1 MODE PICTURE button
(page 32)
This button is to display the
PICTURE MODE menu.
2 MEMORY USER button
(page 36)
This button is to display the
MEMORY LOAD menu.
3 VOLUME +/- buttons
These buttons are used to adjust
the volume of the sound output
from the projector’s built-in
speaker.
4 SD button
(page 43)
This button is to select the SD
CARD screen.
5 SD MENU button
(page 43)
This button can be used to return
to a previous screen when SD
CARD screen is selected.
6 SD TIME button
(page 49)
This button is used to display or
clear the playing time when a
moving picture stored on the SD
card is played back.
15
Preparation
<Projector control panel and remote control unit>
'
(
)
/
POWER
&
LIGHT
INPUT
VID E O
'
(
)
,
.
#
$
CMPNT
PC
COMPONENT
KEYSTONE
MENU
&
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
*
+
+
ENTER
SD
%
*
MENU
0
1
2
3
TIME
LCD PROJECTOR
456
B The remote control unit and the projector itself have the same control
buttons available.
# TEMP indicator
(page 51)
This indicator illuminates if an
abnormally high temperature is
detected inside the projector. If
the temperature rises above a
certain level, the power supply
will be turned off automatically
and the indicator will illuminate or
flash.
$ LAMP indicator
(page 52)
This indicator illuminates when it
is time to replace the lamp unit. It
flashes if a circuit abnormality is
detected.
% Power indicator
(pages 22 and 23)
This indicator illuminates red
when the main power is switched
on (Standby Mode), and it
illuminates green when projection
of an image begins.
14
& POWER button
(pages 22 and 23)
' MENU button
(page 24)
This button is used to display
menu screens. When a menu
screen is being displayed, it can
be used to return to a previous
screen or to clear the screen.
F, G, I and H)
( Arrow (F
buttons
(page 26)
These buttons are used to select
and adjust items in the on-screen
menu screens.
) ENTER button
(page 26)
This button is used to accept and
to activate items selected in the
on-screen menus.
* Input select button
(INPUT/VIDEO/COMPONENT/
PC button) (page 22)
+ KEYSTONE buttons
(pages 28 and 29)
This button is used to correct
keystone distortion of the
projected image when the
projector position is tilted upward
or downward.
, NORMAL button
(page 27)
This button is used to reset the
projector adjustment values to the
factory default settings.
- ASPECT button
(page 30)
This button is used for aspect
adjustment (vertical and
horizontal proportions).
. MUTE button
(page 33)
This button momentarily stops
output of the projector’s built-in
speaker.
/ LIGHT button
This button is used to illuminate
the buttons on the remote control
unit.
0 FREEZE button
(page 36)
This button is used to
momentarily freeze projection so
that a still picture is displayed.
1 MODE PICTURE button
(page 32)
This button is to display the
PICTURE MODE menu.
2 MEMORY USER button
(page 36)
This button is to display the
MEMORY LOAD menu.
3 VOLUME +/- buttons
These buttons are used to adjust
the volume of the sound output
from the projector’s built-in
speaker.
4 SD button
(page 43)
This button is to select the SD
CARD screen.
5 SD MENU button
(page 43)
This button can be used to return
to a previous screen when SD
CARD screen is selected.
6 SD TIME button
(page 49)
This button is used to display or
clear the playing time when a
moving picture stored on the SD
card is played back.
15
Preparation
<Projector control panel and remote control unit>
Using the remote control unit
<Connector panel>
<PT-L300U>
#
%
&
'
Preparation
Operating range
(
# Open the cover.
(
$ Insert the batteries so that the polarities are
correct, and then close the cover.
$
<PT-L200U>
#
$
%
'
+
〇
−
〇
−
〇
+
〇
AAA batteries
(two)
# AUDIO L-R input jacks
(page 18)
$ VIDEO input jack
(page 18)
This jack is used to input video
signals from a video equipment
such as a video deck.
% S2 VIDEO input connector
(page 18 and 30)
This connector is used to input
signals from an S-VIDEOcompatible equipment such as a
video deck. The connector is
compatible with S2 and S1
signals, and projector aspect is
automatically adjusted according
to the type of signal received.
16
& DVI-D IN connector
(page 20)
This connector is used to input
DVI-D signals.
' RGB input connector
(page 20)
This connector is used to input
RGB signals from a PC.
( YPBPR(CBCR) input jacks
(page 19)
These jacks are used to input
YPBPR signals from compatible
equipment such as DVD players.
NOTE:
B Do not drop the remote control unit.
B Keep the remote control unit away from liquids.
B Remove the batteries if not using the remote control unit for long periods.
B Do not use rechargeable batteries.
Operating range
If the remote control unit is held so
that it is facing directly in front of the
remote control signal receptors on
the front of the projector, the
operating range is within
approximately 7 m (23´) from the
surfaces of the receptors.
Furthermore, the remote control unit
can be operated from an angle of
±30° to the left or right and ±15°
above or below the receptors.
NOTE:
B If there are any obstacles in between
the remote control unit and the
receivers, the remote control unit may
not operate correctly.
B If strong light is allowed to shine onto
the remote control signal receiver,
correct remote control operation may
not be possible. Place the projector as
far away from light sources as possible.
B If facing the remote control unit
toward the screen to operate the
projector, the operating range of the
remote control unit will be limited by
the amount of light reflection loss
caused by the characteristics of the
screen used.
17
Using the remote control unit
<Connector panel>
<PT-L300U>
#
%
&
'
Preparation
Operating range
(
# Open the cover.
(
$ Insert the batteries so that the polarities are
correct, and then close the cover.
$
<PT-L200U>
#
$
%
'
+
〇
−
〇
−
〇
+
〇
AAA batteries
(two)
# AUDIO L-R input jacks
(page 18)
$ VIDEO input jack
(page 18)
This jack is used to input video
signals from a video equipment
such as a video deck.
% S2 VIDEO input connector
(page 18 and 30)
This connector is used to input
signals from an S-VIDEOcompatible equipment such as a
video deck. The connector is
compatible with S2 and S1
signals, and projector aspect is
automatically adjusted according
to the type of signal received.
16
& DVI-D IN connector
(page 20)
This connector is used to input
DVI-D signals.
' RGB input connector
(page 20)
This connector is used to input
RGB signals from a PC.
( YPBPR(CBCR) input jacks
(page 19)
These jacks are used to input
YPBPR signals from compatible
equipment such as DVD players.
NOTE:
B Do not drop the remote control unit.
B Keep the remote control unit away from liquids.
B Remove the batteries if not using the remote control unit for long periods.
B Do not use rechargeable batteries.
Operating range
If the remote control unit is held so
that it is facing directly in front of the
remote control signal receptors on
the front of the projector, the
operating range is within
approximately 7 m (23´) from the
surfaces of the receptors.
Furthermore, the remote control unit
can be operated from an angle of
±30° to the left or right and ±15°
above or below the receptors.
NOTE:
B If there are any obstacles in between
the remote control unit and the
receivers, the remote control unit may
not operate correctly.
B If strong light is allowed to shine onto
the remote control signal receiver,
correct remote control operation may
not be possible. Place the projector as
far away from light sources as possible.
B If facing the remote control unit
toward the screen to operate the
projector, the operating range of the
remote control unit will be limited by
the amount of light reflection loss
caused by the characteristics of the
screen used.
17
Connections
Example of connecting to equipment compatible
with YPBPR(CBCR) signals
B Read the instruction manual for each system component carefully before
connecting it.
B Turn off the power supply for all components before making any
connections.
B If the cables necessary for connecting a component to the system are not
included with the component or available as an option, you may need to
fashion a cable to suit the component concerned.
Preparation
Notes on connections
DVD player
To audio
output
To YPBPR
output
Example of connecting to video equipment
DVD player
To audio
output
To S-Video output
* This illustration is an example of
connection for the PT-L300U.
NOTE:
B Refer to page 61 for a list of compatible YPBPR signals which can be input
to the projector.
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
Video/Audio cable
(accessory)
To audio
output
To video output
* This illustration is an example of
connection for the PT-L300U.
Video deck
NOTE:
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
18
19
Connections
Example of connecting to equipment compatible
with YPBPR(CBCR) signals
B Read the instruction manual for each system component carefully before
connecting it.
B Turn off the power supply for all components before making any
connections.
B If the cables necessary for connecting a component to the system are not
included with the component or available as an option, you may need to
fashion a cable to suit the component concerned.
Preparation
Notes on connections
DVD player
To audio
output
To YPBPR
output
Example of connecting to video equipment
DVD player
To audio
output
To S-Video output
* This illustration is an example of
connection for the PT-L300U.
NOTE:
B Refer to page 61 for a list of compatible YPBPR signals which can be input
to the projector.
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
Video/Audio cable
(accessory)
To audio
output
To video output
* This illustration is an example of
connection for the PT-L300U.
Video deck
NOTE:
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
18
19
Setting-up
Computer
Computer
Projection methods
Preparation
Example of connecting to computer
The projector can be set up so that any one of the following four projection
methods can be used. Select whichever projection method matches the
setting-up method. (The projection method can be set from the OPTION
menu. Refer to page 40 for details.)
DESK/CEILING
DESK
To audio
output
To DVI-D
output
To audio
output
To RGB
output
CEILING
FRONT
(Factory default setting)
FRONT/REAR
REAR
NOTE:
B You will need to purchase the separate ceiling bracket (ET-PKE300) when
using the ceiling installation method.
* This illustration is an example of
connection for the PT-L300U.
NOTE:
B It is better to shut down the computer before turning off the MAIN POWER
switch of the projector.
B Refer to the list of compatible signals on page 61 for the types of RGB
signals which can be input to the projector by connecting a computer.
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
B The PT-L200U does not have a DVI-D input (DVI-D IN) connector.
Projector position
The projection range of this projector is 1.2 m – 7.4 m.
The lower edge of the projected image falls about 0.1 m from the center of
the lens.
For details about projected image distances, refer to page 65.
Projection Distance
Screen Size Diagonal length 40˝
(16:9)
0.5 m
Height
(1´7˝)
Projection
0.9
m
Width
Distance
(2´11˝)
Minimum Distance
Maximum Distance
20
1.2 m
(3´11˝)
1.4 m
(4´7˝)
60˝
80˝
100˝
150˝
200˝
0.8 m 1.0 m 1.3 m 1.9 m 2.5 m
(2´7˝)
(3´3˝)
(4´3˝)
(6´2˝)
(8´2˝)
1.3 m 1.8 m 2.2 m 3.3 m 4.4 m
(4´3˝) (5´10˝) (7´2˝) (10´9˝) (14´5˝)
1.9 m
(6´2˝)
2.2 m
(7´2˝)
2.5 m
(8´2˝)
2.9 m
(9´6˝)
3.1 m
(10´2˝)
3.7 m
(12´1˝)
4.7 m
(15´5˝)
5.6 m
(18´4˝)
6.2 m
(20´4˝)
7.4 m
(24´3˝)
21
Setting-up
Computer
Computer
Projection methods
Preparation
Example of connecting to computer
The projector can be set up so that any one of the following four projection
methods can be used. Select whichever projection method matches the
setting-up method. (The projection method can be set from the OPTION
menu. Refer to page 40 for details.)
DESK/CEILING
DESK
To audio
output
To DVI-D
output
To audio
output
To RGB
output
CEILING
FRONT
(Factory default setting)
FRONT/REAR
REAR
NOTE:
B You will need to purchase the separate ceiling bracket (ET-PKE300) when
using the ceiling installation method.
* This illustration is an example of
connection for the PT-L300U.
NOTE:
B It is better to shut down the computer before turning off the MAIN POWER
switch of the projector.
B Refer to the list of compatible signals on page 61 for the types of RGB
signals which can be input to the projector by connecting a computer.
B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs.
B The PT-L200U does not have a DVI-D input (DVI-D IN) connector.
Projector position
The projection range of this projector is 1.2 m – 7.4 m.
The lower edge of the projected image falls about 0.1 m from the center of
the lens.
For details about projected image distances, refer to page 65.
Projection Distance
Screen Size Diagonal length 40˝
(16:9)
0.5 m
Height
(1´7˝)
Projection
0.9
m
Width
Distance
(2´11˝)
Minimum Distance
Maximum Distance
20
1.2 m
(3´11˝)
1.4 m
(4´7˝)
60˝
80˝
100˝
150˝
200˝
0.8 m 1.0 m 1.3 m 1.9 m 2.5 m
(2´7˝)
(3´3˝)
(4´3˝)
(6´2˝)
(8´2˝)
1.3 m 1.8 m 2.2 m 3.3 m 4.4 m
(4´3˝) (5´10˝) (7´2˝) (10´9˝) (14´5˝)
1.9 m
(6´2˝)
2.2 m
(7´2˝)
2.5 m
(8´2˝)
2.9 m
(9´6˝)
3.1 m
(10´2˝)
3.7 m
(12´1˝)
4.7 m
(15´5˝)
5.6 m
(18´4˝)
6.2 m
(20´4˝)
7.4 m
(24´3˝)
21
Starting to use
) Turn the focus/zoom ring to adjust
the projected image focus and size.
Turning on the power
Zoom
Focus
Please ensure that all preparations have been completed before turning on
the power. (Refer to pages 18 – 21.)
# Remove the lens cover.
$ Connect the accessory power cord.
% Press the MAIN POWER switch to
the “|” side to turn on the power.
The power indicator on the projector
will illuminate red.
& Press the POWER button.
The power indicator on the projector
will flash green. After a short period,
the button will illuminate green, and a
picture will be projected.
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
FREEZE
ASPECT
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
' Press the INPUT select button to
select the input signal.
The input signal selected will change
as shown at below-right each time an
input select button (INPUT/VIDEO/
CMPNT/PC/SD) is pressed.
VID E O
INPUT
S-VIDEO
VIDEO
TIME
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
PC
MENU
TIME
DVI
PC
SD CARD
DVI
PC
Y・PB・PR
S-VIDEO
VIDEO
CMPNT
SD
Y・PB・PR
( While pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector.
If there is keystone distortion in the
projected images, carry out keystone
correction as described on page 28.
22
MENU
SD CARD
*“DVI” is only
for PT-L300U.
# Press the POWER button. “POWER OFF” is
POWER OFF
displayed on the screen.
OK
CANCEL
$ Select “OK” using the I and H buttons and
press the ENTER button.
The lamp unit will switch off and the picture will stop being projected. (The
power indicator on the projector will illuminate orange.)
% Wait until the power indicator on the projector illuminates red (until
the cooling fan stops).
Do not in any way cut power to the projector while the cooling fan is still
operating. Be careful not to switch off the MAIN POWER switch of the
projector, unplug the power cord from the electrical outlet or turn off in-line
switches such as tabletop power switches.
& Press the MAIN POWER switch to the “O” side to turn off the power.
NOTE:
B After the power is turned off, the lamp unit will take some time to cool
down. If you turn the power back on again before the lamp unit has cooled
down, the lamp unit may not turn on straight away, but it will turn on
automatically after a short period. (During this time, the power indicator on
the projector will flash orange.)
B When the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector will still draw a maximum 1.5 W
of power, even when the cooling fan has stopped.
B If the MAIN POWER switch is accidentally turned off while the projector is
being used, the lamp unit may not turn on straight away after the power is
turned back on. In such cases, the lamp unit will turn back on
automatically after a short period. (During this time, the power indicator on
the projector will flash green.)
B A tinkling sound may be heard while the power indicator is turned off, but
this is not a sign of a malfunction.
B You can also turn off the power by pressing the POWER button twice or
by holding down it for at least 0.5 seconds.
23
Basic Operation
Turning off the power
Starting to use
) Turn the focus/zoom ring to adjust
the projected image focus and size.
Turning on the power
Zoom
Focus
Please ensure that all preparations have been completed before turning on
the power. (Refer to pages 18 – 21.)
# Remove the lens cover.
$ Connect the accessory power cord.
% Press the MAIN POWER switch to
the “|” side to turn on the power.
The power indicator on the projector
will illuminate red.
& Press the POWER button.
The power indicator on the projector
will flash green. After a short period,
the button will illuminate green, and a
picture will be projected.
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
FREEZE
ASPECT
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
' Press the INPUT select button to
select the input signal.
The input signal selected will change
as shown at below-right each time an
input select button (INPUT/VIDEO/
CMPNT/PC/SD) is pressed.
VID E O
INPUT
S-VIDEO
VIDEO
TIME
POWER
LIGHT
INPUT
VID E O
CMPNT
PC
COMPONENT
KEYSTONE
MENU
ENTER
NORMAL
ASPECT
FREEZE
MODE
MEMORY
PICTURE
USER
VOLUME
MUTE
SD
SD
PC
MENU
TIME
DVI
PC
SD CARD
DVI
PC
Y・PB・PR
S-VIDEO
VIDEO
CMPNT
SD
Y・PB・PR
( While pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector.
If there is keystone distortion in the
projected images, carry out keystone
correction as described on page 28.
22
MENU
SD CARD
*“DVI” is only
for PT-L300U.
# Press the POWER button. “POWER OFF” is
POWER OFF
displayed on the screen.
OK
CANCEL
$ Select “OK” using the I and H buttons and
press the ENTER button.
The lamp unit will switch off and the picture will stop being projected. (The
power indicator on the projector will illuminate orange.)
% Wait until the power indicator on the projector illuminates red (until
the cooling fan stops).
Do not in any way cut power to the projector while the cooling fan is still
operating. Be careful not to switch off the MAIN POWER switch of the
projector, unplug the power cord from the electrical outlet or turn off in-line
switches such as tabletop power switches.
& Press the MAIN POWER switch to the “O” side to turn off the power.
NOTE:
B After the power is turned off, the lamp unit will take some time to cool
down. If you turn the power back on again before the lamp unit has cooled
down, the lamp unit may not turn on straight away, but it will turn on
automatically after a short period. (During this time, the power indicator on
the projector will flash orange.)
B When the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector will still draw a maximum 1.5 W
of power, even when the cooling fan has stopped.
B If the MAIN POWER switch is accidentally turned off while the projector is
being used, the lamp unit may not turn on straight away after the power is
turned back on. In such cases, the lamp unit will turn back on
automatically after a short period. (During this time, the power indicator on
the projector will flash green.)
B A tinkling sound may be heard while the power indicator is turned off, but
this is not a sign of a malfunction.
B You can also turn off the power by pressing the POWER button twice or
by holding down it for at least 0.5 seconds.
23
Basic Operation
Turning off the power
PICTURE menu (page 34)
When an S-VIDEO/VIDEO signal
is being input
Menu screens
The various settings and adjustments for this projector can be carried out by
selecting the operations from on-screen menus.
The general arrangement of these menus is shown below.
Keystone correction
(page 28)
For PT-L300U
MAIN MENU
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
K E Y S T O N E
H-KEYSTONE
0
V-KEYSTONE
0
SELECT
ENTER
ESC
For PT-L200U
KEYSTONE
0
* Only vertical keystone distortion
is corrected by PT-L200U.
EXIT
SD menu (page 43)
SHUTTER function
(page 33)
PICTURE
SLIDE SHOW
VIDEO
OPTION menu (page 39)
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
Volume adjustment
Press the ENTER button, and
then press the I and H
buttons to adjust the volume.
LANGUAGE menu (page 33)
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
ENTER
ENGLISH
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
When a YPBPR signal is being
input or SD CARD is selected
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525I
SELECT
ADJ
ESC
When a PC/DVI signal is being input
Basic Operation
On-screen menus
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
SHARPNESS
0
COLOR TEMP.
0
W-BAL R
0
W-BAL G
0
W-BAL B
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
XGA
SELECT
ADJ
ESC
* “GAMMA ADJUST” is not displayed by PT-L200U.
* “W-BAL R”, “W-BAL G” and “W-BAL B” are not displayed when DVI signal
is being input.
POSITION menu (page 38)
When an S-VIDEO/VIDEO/YPBPR/
DVI signal is being input or SD
CARD is selected
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
* “ASPECT” can be adjusted only
when a DVI signal is being input
or when “SD CARD” is selected.
When a PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
ESC
NOTE:
B Keystone distortion of the on-screen display will not be corrected.
(PT-L200U only)
24
25
PICTURE menu (page 34)
When an S-VIDEO/VIDEO signal
is being input
Menu screens
The various settings and adjustments for this projector can be carried out by
selecting the operations from on-screen menus.
The general arrangement of these menus is shown below.
Keystone correction
(page 28)
For PT-L300U
MAIN MENU
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
K E Y S T O N E
H-KEYSTONE
0
V-KEYSTONE
0
SELECT
ENTER
ESC
For PT-L200U
KEYSTONE
0
* Only vertical keystone distortion
is corrected by PT-L200U.
EXIT
SD menu (page 43)
SHUTTER function
(page 33)
PICTURE
SLIDE SHOW
VIDEO
OPTION menu (page 39)
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
Volume adjustment
Press the ENTER button, and
then press the I and H
buttons to adjust the volume.
LANGUAGE menu (page 33)
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
ENTER
ENGLISH
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
When a YPBPR signal is being
input or SD CARD is selected
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525I
SELECT
ADJ
ESC
When a PC/DVI signal is being input
Basic Operation
On-screen menus
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
SHARPNESS
0
COLOR TEMP.
0
W-BAL R
0
W-BAL G
0
W-BAL B
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
XGA
SELECT
ADJ
ESC
* “GAMMA ADJUST” is not displayed by PT-L200U.
* “W-BAL R”, “W-BAL G” and “W-BAL B” are not displayed when DVI signal
is being input.
POSITION menu (page 38)
When an S-VIDEO/VIDEO/YPBPR/
DVI signal is being input or SD
CARD is selected
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
* “ASPECT” can be adjusted only
when a DVI signal is being input
or when “SD CARD” is selected.
When a PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
ESC
NOTE:
B Keystone distortion of the on-screen display will not be corrected.
(PT-L200U only)
24
25
# Press the MENU button.
The MAIN MENU screen will be
displayed.
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
BRIGHT
EXIT
$ Press the F or G arrow
buttons to select an item.
Selected items will be displayed
in blue.
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
EXIT
% Press the ENTER button to
accept the selection.
The selected menu screen or
adjustment screen will then be
displayed.
(Example: PICTURE menu)
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
26
& Press the F or G buttons to
select an item, and then press
the I or H buttons to change
or adjust the setting.
An individual adjustment screen
such as the one shown below will
be displayed for bar-scale items.
0
The bar scale will turn green
when any adjustment changes
the setting from the factory set
value.
For items without any selective
arrow or bar-scale, press the
ENTER button. The menu screen
for the item will then be
displayed.
Unavailable on-screen
menu items
This projector has unadjustable
items and unusable functions
depending on the signal being input.
When an item cannot be adjusted or
a function cannot be used, the
corresponding on-screen menu
display does not appear, and the
item or function will not work even if
the ENTER button is pressed.
Returning to the
previous screen
If you press the MENU button while
a menu screen is being displayed,
the display will return to the
previous screen.
If you press the MENU button while
the MAIN MENU screen is being
displayed, the MAIN MENU screen
will be cleared.
Returning a setting to
the factory default
B When an individual adjustment
screen is being displayed
If you press the NORMAL button on
the remote control unit, you can
return settings to the factory default
settings. However, the operation of
this function varies depending on
which screen is being displayed.
B When a menu screen is being
displayed
BRIGHT
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
All items displayed will be returned
to their factory default settings, and
the bar scale will appear white.
0
Only the item displayed will be
returned to the factory default
setting, and the bar scale will
appear white.
NOTE:
B Triangle symbols above and
below a menu bar indicate the
factory default setting. Items
which do not have these triangle
symbols cannot be returned to
the factory default setting.
Indicates the standard factory
default setting
Indicates the current adjustment
value
B The positions of triangle symbols
vary depending on the type of
signal being input.
Using the freeze function
The picture will alternate between a still picture and a moving picture each
time the FREEZE button on the remote control unit is pressed.
Still picture
Moving picture
27
Basic Operation
Menu operation guide
# Press the MENU button.
The MAIN MENU screen will be
displayed.
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
BRIGHT
EXIT
$ Press the F or G arrow
buttons to select an item.
Selected items will be displayed
in blue.
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
EXIT
% Press the ENTER button to
accept the selection.
The selected menu screen or
adjustment screen will then be
displayed.
(Example: PICTURE menu)
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
26
& Press the F or G buttons to
select an item, and then press
the I or H buttons to change
or adjust the setting.
An individual adjustment screen
such as the one shown below will
be displayed for bar-scale items.
0
The bar scale will turn green
when any adjustment changes
the setting from the factory set
value.
For items without any selective
arrow or bar-scale, press the
ENTER button. The menu screen
for the item will then be
displayed.
Unavailable on-screen
menu items
This projector has unadjustable
items and unusable functions
depending on the signal being input.
When an item cannot be adjusted or
a function cannot be used, the
corresponding on-screen menu
display does not appear, and the
item or function will not work even if
the ENTER button is pressed.
Returning to the
previous screen
If you press the MENU button while
a menu screen is being displayed,
the display will return to the
previous screen.
If you press the MENU button while
the MAIN MENU screen is being
displayed, the MAIN MENU screen
will be cleared.
Returning a setting to
the factory default
B When an individual adjustment
screen is being displayed
If you press the NORMAL button on
the remote control unit, you can
return settings to the factory default
settings. However, the operation of
this function varies depending on
which screen is being displayed.
B When a menu screen is being
displayed
BRIGHT
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
All items displayed will be returned
to their factory default settings, and
the bar scale will appear white.
0
Only the item displayed will be
returned to the factory default
setting, and the bar scale will
appear white.
NOTE:
B Triangle symbols above and
below a menu bar indicate the
factory default setting. Items
which do not have these triangle
symbols cannot be returned to
the factory default setting.
Indicates the standard factory
default setting
Indicates the current adjustment
value
B The positions of triangle symbols
vary depending on the type of
signal being input.
Using the freeze function
The picture will alternate between a still picture and a moving picture each
time the FREEZE button on the remote control unit is pressed.
Still picture
Moving picture
27
Basic Operation
Menu operation guide
Correcting keystone distortion
When either the projector or the screen is tilted, the keystone distortion will
affect the image. You can correct the image proportions by the following
procedure.
For PT-L300U
For PT-L200U
Horizontal and vertical keystone distortion can be corrected by following
procedures.
# Press the KEYSTONE button to display K E Y S T O N E
H-KEYSTONE
0
the KEYSTONE menu.
Vertical keystone distortion can be corrected by following procedures.
# Use the KEYSTONE button to
obtain image balance.
KEYSTONE
0
$ To correct vertical keystone distortion
Select “V-KEYSTONE” by pressing
K E Y S T O N E
H-KEYSTONE
0
the F or G buttons and then press
V-KEYSTONE
0
the ENTER button.
SELECT
ENTER
ESC
Picture condition
Operation
$ Press the MENU button to return to the previous screen.
Picture condition
Operation
Press the Hbutton. Press the Ibutton.
Press the Hbutton. Press the Ibutton.
% To correct the horizontal keystone distortion
Select “H-KEYSTONE” by pressing
K E Y S T O N E
H-KEYSTONE
0
the F or G buttons and then press
V-KEYSTONE
0
the ENTER button.
SELECT
ENTER
ESC
Picture condition
Operation
Press the Hbutton. Press the Ibutton.
& Press the MENU button.
The display will then return to the previous screen.
28
NOTE:
B You can also correct keystone distortion by selecting the KEYSTONE item
in the MAIN MENU and pressing ENTER.
B Vertical and horizontal keystone distortion can be corrected to ±30° of the
angle of tilt by PT-L300U. Vertical keystone distortion can be corrected to
±30° of the angle of tilt by PT-L200U. However, the greater the correction
amount, the more the picture quality will deteriorate, and the harder it will
become to achieve a good level of focus. To obtain the best picture
quality, set up the projector and screen in such a way that the amount of
keystone correction required is as minimal as possible.
B The picture size will also change when correction of keystone distortion is
carried out.
29
Basic Operation
V-KEYSTONE
0
SELECT
ENTER
ESC
Correcting keystone distortion
When either the projector or the screen is tilted, the keystone distortion will
affect the image. You can correct the image proportions by the following
procedure.
For PT-L300U
For PT-L200U
Horizontal and vertical keystone distortion can be corrected by following
procedures.
# Press the KEYSTONE button to display K E Y S T O N E
H-KEYSTONE
0
the KEYSTONE menu.
Vertical keystone distortion can be corrected by following procedures.
# Use the KEYSTONE button to
obtain image balance.
KEYSTONE
0
$ To correct vertical keystone distortion
Select “V-KEYSTONE” by pressing
K E Y S T O N E
H-KEYSTONE
0
the F or G buttons and then press
V-KEYSTONE
0
the ENTER button.
SELECT
ENTER
ESC
Picture condition
Operation
$ Press the MENU button to return to the previous screen.
Picture condition
Operation
Press the Hbutton. Press the Ibutton.
Press the Hbutton. Press the Ibutton.
% To correct the horizontal keystone distortion
Select “H-KEYSTONE” by pressing
K E Y S T O N E
H-KEYSTONE
0
the F or G buttons and then press
V-KEYSTONE
0
the ENTER button.
SELECT
ENTER
ESC
Picture condition
Operation
Press the Hbutton. Press the Ibutton.
& Press the MENU button.
The display will then return to the previous screen.
28
NOTE:
B You can also correct keystone distortion by selecting the KEYSTONE item
in the MAIN MENU and pressing ENTER.
B Vertical and horizontal keystone distortion can be corrected to ±30° of the
angle of tilt by PT-L300U. Vertical keystone distortion can be corrected to
±30° of the angle of tilt by PT-L200U. However, the greater the correction
amount, the more the picture quality will deteriorate, and the harder it will
become to achieve a good level of focus. To obtain the best picture
quality, set up the projector and screen in such a way that the amount of
keystone correction required is as minimal as possible.
B The picture size will also change when correction of keystone distortion is
carried out.
29
Basic Operation
V-KEYSTONE
0
SELECT
ENTER
ESC
This projector allows you to change the aspect ratio to match the type of
input signal. Pressing the ASPECT button will change the aspect ratio
according to the successive settings shown below.
(You can also change the aspect ratio by selecting the POSITION item in the
MAIN MENU and pressing ENTER.)
S-VIDEO
VIDEO/YPBPR
PC
DVI
SD CARD
S1/S2\4:3\16:9\JUST\ZOOM\*S4:3\*S16:9
4:3\16:9\JUST\ZOOM\*S4:3\*S16:9
4:3\16:9\V SCROLL
4:3\16:9
4:3\16:9\JUST\ZOOM
* “S4:3” or “S16:9” can be selected when NTSC, M-NTSC, PAL-M, PAL60,
525p and 525i signals are being input to the PT-L300U.
ASPECT
Input signal
4:3
4:3 Input signal
4:3
16:9
Squeezed signal (image
contracted horizontally)
Horizontal expansion of
projected image
JUST
4:3 Input signal
Horizontal expansion of projected image
(Center of image is less distorted)
ZOOM
Letter box signal
Expansion preserves
original ratio
V SCROLL
4:3 Input signal
Enlarges image approximately 1.2
times (Vertical position can be
adjusted by the G and F buttons)
S4:3
4:3 Input signal
S16:9
(PT-L300U only)
Image which is projected at an
aspect ratio of 4:3 or 16:9 without
being expanded vertically.
Illustrations for aspect ratio settings are shown on the next page. Refer to
this illustration for assistance in selecting a suitable aspect ratio.
About S1/S2 video signals:
B S1/S2 video signals are for 16:9 images and include a notification signal
when being played by devices such as a DVD player.
B When the projector is set to the “S1/S2” setting shown above, it will detect
those notification signals and automatically switch to the correct aspect
ratio for projection.
NOTE:
B This projector is equipped with an aspect ratio selection function. However, if a
mode which does not match the aspect ratio of the input signal is selected, it
may affect the quality of viewing of the original picture. Keep this in mind when
selecting the aspect ratio.
B If using this projector in places such as cafes or hotels with the aim of
displaying programmes for viewing for a commercial purpose or for public
presentation, note that if the aspect ratio (16:9) selection function is used to
change the aspect ratio of the screen picture, you may be infringing the rights
of the original copyright owner for that program under copyright protection laws.
B If a normal (4:3) picture which was not originally intended for wide-screen
viewing is projected onto a wide screen, distortion may occur around the edges
of the picture so that part of the picture is no longer visible. Such programmes
should be viewed in 4:3 mode to give proper consideration to the aims and
intentions of the original program’s creator.
B The following signals have resolutions that are 16:9 image sizes. The aspect
ratios for these signals cannot be changed while being played because they
are already established. (Refer to page 61.)
HDTV60, HDTV50, 750p, WIDE 400/480/600/720/768
B Image sizes such as Cinema-Vision that project wider than the 16:9 ratio will
have narrow black fields at the top and bottom.
30
Projected Image
Basic Operation
Setting the ASPECT
31
This projector allows you to change the aspect ratio to match the type of
input signal. Pressing the ASPECT button will change the aspect ratio
according to the successive settings shown below.
(You can also change the aspect ratio by selecting the POSITION item in the
MAIN MENU and pressing ENTER.)
S-VIDEO
VIDEO/YPBPR
PC
DVI
SD CARD
S1/S2\4:3\16:9\JUST\ZOOM\*S4:3\*S16:9
4:3\16:9\JUST\ZOOM\*S4:3\*S16:9
4:3\16:9\V SCROLL
4:3\16:9
4:3\16:9\JUST\ZOOM
* “S4:3” or “S16:9” can be selected when NTSC, M-NTSC, PAL-M, PAL60,
525p and 525i signals are being input to the PT-L300U.
ASPECT
Input signal
4:3
4:3 Input signal
4:3
16:9
Squeezed signal (image
contracted horizontally)
Horizontal expansion of
projected image
JUST
4:3 Input signal
Horizontal expansion of projected image
(Center of image is less distorted)
ZOOM
Letter box signal
Expansion preserves
original ratio
V SCROLL
4:3 Input signal
Enlarges image approximately 1.2
times (Vertical position can be
adjusted by the G and F buttons)
S4:3
4:3 Input signal
S16:9
(PT-L300U only)
Image which is projected at an
aspect ratio of 4:3 or 16:9 without
being expanded vertically.
Illustrations for aspect ratio settings are shown on the next page. Refer to
this illustration for assistance in selecting a suitable aspect ratio.
About S1/S2 video signals:
B S1/S2 video signals are for 16:9 images and include a notification signal
when being played by devices such as a DVD player.
B When the projector is set to the “S1/S2” setting shown above, it will detect
those notification signals and automatically switch to the correct aspect
ratio for projection.
NOTE:
B This projector is equipped with an aspect ratio selection function. However, if a
mode which does not match the aspect ratio of the input signal is selected, it
may affect the quality of viewing of the original picture. Keep this in mind when
selecting the aspect ratio.
B If using this projector in places such as cafes or hotels with the aim of
displaying programmes for viewing for a commercial purpose or for public
presentation, note that if the aspect ratio (16:9) selection function is used to
change the aspect ratio of the screen picture, you may be infringing the rights
of the original copyright owner for that program under copyright protection laws.
B If a normal (4:3) picture which was not originally intended for wide-screen
viewing is projected onto a wide screen, distortion may occur around the edges
of the picture so that part of the picture is no longer visible. Such programmes
should be viewed in 4:3 mode to give proper consideration to the aims and
intentions of the original program’s creator.
B The following signals have resolutions that are 16:9 image sizes. The aspect
ratios for these signals cannot be changed while being played because they
are already established. (Refer to page 61.)
HDTV60, HDTV50, 750p, WIDE 400/480/600/720/768
B Image sizes such as Cinema-Vision that project wider than the 16:9 ratio will
have narrow black fields at the top and bottom.
30
Projected Image
Basic Operation
Setting the ASPECT
31
Using the shutter function
You can select the appropriate picture mode for the type of projected image
by the following procedure.
(The picture mode can be also selected in the PICTURE menu.)
# Press the MODE PICTURE button to display the PICTURE menu.
The shutter function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in shutter mode than it does in
normal projection mode.
# Select SHUTTER from the MAIN MENU screen and then press the
ENTER button.
$ Press any button on either the projector or remote control unit to
return to normal operating mode.
PICTURE MODE
NORMAL
$ Select an item by pressing the I or H buttons.
When S-VIDEO/VIDEO/YPBPR is
being input or when SD CARD is
selected
When PC/DVI is being input
PICTURE MODE
PICTURE MODE
NORMAL
Changing the display language
[
DYNAMIC
[
CINEMA1
[
CINEMA2
[
MUSIC
[
SPORTS
NORMAL
[
DYNAMIC
[
CINEMA1
[
CINEMA2
# Select LANGUAGE from the MAIN MENU screen and then press the
ENTER button.
$ Use the FG buttons to select a language and then press the ENTER
button.
[
MUSIC
[
NATURAL
NORMAL ............When the brightness of the room is at a standard level.
DYNAMIC ...........When the room is brighter.
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
ENTER
ENGLISH
Indicates the language which is
currently set
ESC
CINEMA1 ............When watching movies.
CINEMA2 ............When watching movies with lighter and clearer pictures.
MUSIC ................When watching music programs such as concerts or live
performances.
SPORTS .............When watching sports programs such as baseball or
soccer games.
Muting the sound
The sound can be muted for temporary interruptions such as telephone calls.
Press the MUTE button once to turn off sound, and press MUTE again to
regain sound.
NATURAL...........To project the image faithfully from the image source.
NOTE:
B If the power is turned off or the VOLUME +/- buttons are pressed, the
mute will be canceled.
32
33
Basic Operation
Selecting the picture mode
Using the shutter function
You can select the appropriate picture mode for the type of projected image
by the following procedure.
(The picture mode can be also selected in the PICTURE menu.)
# Press the MODE PICTURE button to display the PICTURE menu.
The shutter function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in shutter mode than it does in
normal projection mode.
# Select SHUTTER from the MAIN MENU screen and then press the
ENTER button.
$ Press any button on either the projector or remote control unit to
return to normal operating mode.
PICTURE MODE
NORMAL
$ Select an item by pressing the I or H buttons.
When S-VIDEO/VIDEO/YPBPR is
being input or when SD CARD is
selected
When PC/DVI is being input
PICTURE MODE
PICTURE MODE
NORMAL
Changing the display language
[
DYNAMIC
[
CINEMA1
[
CINEMA2
[
MUSIC
[
SPORTS
NORMAL
[
DYNAMIC
[
CINEMA1
[
CINEMA2
# Select LANGUAGE from the MAIN MENU screen and then press the
ENTER button.
$ Use the FG buttons to select a language and then press the ENTER
button.
[
MUSIC
[
NATURAL
NORMAL ............When the brightness of the room is at a standard level.
DYNAMIC ...........When the room is brighter.
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT
ENTER
ENGLISH
Indicates the language which is
currently set
ESC
CINEMA1 ............When watching movies.
CINEMA2 ............When watching movies with lighter and clearer pictures.
MUSIC ................When watching music programs such as concerts or live
performances.
SPORTS .............When watching sports programs such as baseball or
soccer games.
Muting the sound
The sound can be muted for temporary interruptions such as telephone calls.
Press the MUTE button once to turn off sound, and press MUTE again to
regain sound.
NATURAL...........To project the image faithfully from the image source.
NOTE:
B If the power is turned off or the VOLUME +/- buttons are pressed, the
mute will be canceled.
32
33
Basic Operation
Selecting the picture mode
Use the F and G buttons to select an
item, and then use the I and H buttons
to change the setting for that item.
For items with bar scales, press the
ENTER button or the I or H
buttons to display the adjustment
screen, and then use the I or H
buttons to make the adjustment.
For items without any selective
arrow or bar-scale, press the ENTER
button. The menu screen for the item
will then be displayed.
When an S-VIDEO/VIDEO signal is
being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
When a YPBPR signal is being input
or SD CARD is selected
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525I
SELECT
ADJ
ESC
When a PC/DVI signal is being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
SHARPNESS
0
COLOR TEMP.
0
W-BAL R
0
W-BAL G
0
W-BAL B
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
XGA
SELECT
ADJ
ESC
B “W-BAL R”, “W-BAL G” and “WBAL B” are not displayed when
DVI signal is being input.
PICTURE MODE
Refer to page 32 for details.
CONTRAST
This adjusts the contrast of the
picture. Press the H button to make
the picture brighter, and press the
I button to make the picture
darker. (Adjust the BRIGHT setting
first if required before adjusting the
CONTRAST setting.)
BRIGHT
This adjusts the darker areas (black
areas) in the picture. Press the H
button if dark areas are too solid (for
example, if hair is difficult to see),
and press the I button if black
areas are too light (grey rather than
black).
COLOR
(S-VIDEO/VIDEO/YPBPR /SD
CARD only)
Press the H button to make the
color more vivid in tone, and press
the I button to make the color
more pastel in tone.
34
TINT
(NTSC/NTSC 4.43/YPBPR /SD
CARD only)
This adjusts the flesh tones in the
picture. Press the H button to make
flesh tones more greenish, and
press the I button to make the
flesh tones more reddish.
SHARPNESS
COLOR TEMP.
-2
COLOR TEMP.
-1
[
[
COLOR TEMP.
0
COLOR TEMP.
+1
COLOR TEMP.
+2
COLOR TEMP.
USER
[
[
[
Press the H button to make the
picture details sharper, and press
the I button to make the picture
details softer.
TV SYSTEM
(S-VIDEO/VIDEO only)
TV-SYSTEM
Color Hue Setting (color
temperature)
AUTO1
[
AUTO2
[
NTSC
[
NTSC4.43
[
PAL
[
PAL-M
[
PAL-N
[
SECAM
AUTO1 The projector
automatically distinguishes
between NTSC/NTSC
4.43/PAL/PAL60/SECAM
signals.
AUTO2 The projector
automatically distinguishes
between NTSC/PALM/PAL-N signals.
This should normally be set to
“AUTO1” or “AUTO2”. If the signal is
of such poor quality that the correct
format cannot be automatically
distinguished, change the setting
manually to the required TV system.
* “USER” will not be displayed by
PT-L200U.
This is used to adjust the white
areas of the picture if they appear
bluish or reddish.
USER (PT-L300U only)
This item lets you make fine
adjustments to the color
temperature.
# Press the I or H buttons to
select the “USER” and press the
ENTER button.
COLOR TEMP.
USER
$ Press the F or G buttons to select
an item and adjust the setting by
pressing the I or H buttons.
C O L O R
TEMP.
CONTRAST R
0
CONTRAST B
0
BRITHT R
0
BRITHT B
0
SELECT
ENTER
ESC
If the white area of the picture
appears bluish, adjust CONTRAST
B or BRIGHT B to a lower setting or
adjust the CONTRAST R or
BRIGHT R to a higher setting.
If it appears reddish, adjust
CONTRAST R or BRIGHT R to a
lower setting or adjust the
CONTRAST B or BRIGHT B to a
higher setting.
Adjust settings using CONTRAST R
or CONTRAST B under normal
conditions.
35
Basic Operation
Adjusting the picture
Use the F and G buttons to select an
item, and then use the I and H buttons
to change the setting for that item.
For items with bar scales, press the
ENTER button or the I or H
buttons to display the adjustment
screen, and then use the I or H
buttons to make the adjustment.
For items without any selective
arrow or bar-scale, press the ENTER
button. The menu screen for the item
will then be displayed.
When an S-VIDEO/VIDEO signal is
being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
TV-SYSTEM
AUTO1
SELECT
ADJ
ESC
When a YPBPR signal is being input
or SD CARD is selected
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
COLOR
0
TINT
0
SHARPNESS
0
COLOR TEMP.
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
525I
SELECT
ADJ
ESC
When a PC/DVI signal is being input
PICTURE
PICTURE MODE
NORMAL
CONTRAST
0
BRIGHT
0
SHARPNESS
0
COLOR TEMP.
0
W-BAL R
0
W-BAL G
0
W-BAL B
0
GAMMA ADJUST
MEMORY SAVE
MEMORY LOAD
SIGNAL MODE
XGA
SELECT
ADJ
ESC
B “W-BAL R”, “W-BAL G” and “WBAL B” are not displayed when
DVI signal is being input.
PICTURE MODE
Refer to page 32 for details.
CONTRAST
This adjusts the contrast of the
picture. Press the H button to make
the picture brighter, and press the
I button to make the picture
darker. (Adjust the BRIGHT setting
first if required before adjusting the
CONTRAST setting.)
BRIGHT
This adjusts the darker areas (black
areas) in the picture. Press the H
button if dark areas are too solid (for
example, if hair is difficult to see),
and press the I button if black
areas are too light (grey rather than
black).
COLOR
(S-VIDEO/VIDEO/YPBPR /SD
CARD only)
Press the H button to make the
color more vivid in tone, and press
the I button to make the color
more pastel in tone.
34
TINT
(NTSC/NTSC 4.43/YPBPR /SD
CARD only)
This adjusts the flesh tones in the
picture. Press the H button to make
flesh tones more greenish, and
press the I button to make the
flesh tones more reddish.
SHARPNESS
COLOR TEMP.
-2
COLOR TEMP.
-1
[
[
COLOR TEMP.
0
COLOR TEMP.
+1
COLOR TEMP.
+2
COLOR TEMP.
USER
[
[
[
Press the H button to make the
picture details sharper, and press
the I button to make the picture
details softer.
TV SYSTEM
(S-VIDEO/VIDEO only)
TV-SYSTEM
Color Hue Setting (color
temperature)
AUTO1
[
AUTO2
[
NTSC
[
NTSC4.43
[
PAL
[
PAL-M
[
PAL-N
[
SECAM
AUTO1 The projector
automatically distinguishes
between NTSC/NTSC
4.43/PAL/PAL60/SECAM
signals.
AUTO2 The projector
automatically distinguishes
between NTSC/PALM/PAL-N signals.
This should normally be set to
“AUTO1” or “AUTO2”. If the signal is
of such poor quality that the correct
format cannot be automatically
distinguished, change the setting
manually to the required TV system.
* “USER” will not be displayed by
PT-L200U.
This is used to adjust the white
areas of the picture if they appear
bluish or reddish.
USER (PT-L300U only)
This item lets you make fine
adjustments to the color
temperature.
# Press the I or H buttons to
select the “USER” and press the
ENTER button.
COLOR TEMP.
USER
$ Press the F or G buttons to select
an item and adjust the setting by
pressing the I or H buttons.
C O L O R
TEMP.
CONTRAST R
0
CONTRAST B
0
BRITHT R
0
BRITHT B
0
SELECT
ENTER
ESC
If the white area of the picture
appears bluish, adjust CONTRAST
B or BRIGHT B to a lower setting or
adjust the CONTRAST R or
BRIGHT R to a higher setting.
If it appears reddish, adjust
CONTRAST R or BRIGHT R to a
lower setting or adjust the
CONTRAST B or BRIGHT B to a
higher setting.
Adjust settings using CONTRAST R
or CONTRAST B under normal
conditions.
35
Basic Operation
Adjusting the picture
WHITE BALANCE R/G/B
(PC only)
This is used to adjust the white
areas of the picture if they appear
colourised.
Press the I button to make the
selected color lighter.
Press the H button to make the
selected color stronger.
SIGNAL MODE
(PC/DVI/YPBPR only)
This displays the type of signal
which is currently being projected.
Refer to the table on page 61 for
details on each type of signal.
GAMMA ADJUST
(PT-L300U only)
Press the ENTER button to display
the GAMMA ADJUST menu.
G A M M A
ADJUST
WHITE LEVELS
0
BLACK LEVELS
0
SELECT
ENTER
ESC
WHITE LEVELS
This is used for correcting the
gradation of a bright projected
image. To correct a white jump in
the picture, press the I buttons. To
raise the contrast ratio, press the H
buttons.
BLACK LEVELS
This is used for correcting gradation
of a dark projected image.
To correct black crushing, press the
H buttons. To raise the contrast
ratio, press the I buttons.
MEMORY SAVE
Press the ENTER button to display
the MEMORY SAVE menu.
36
M E M O R Y
SAVE
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
Up to 3 settings can be saved in the
PICTURE menu.
Select the number in which you
wish to save the setting by pressing
the F or G buttons and then press
the ENTER button.
The confirmation screen will then be
displayed. Select “OK” by pressing
the I or H buttons and press the
ENTER button.
MEMORY SAVE
OK
CANCEL
MEMORY LOAD
Press the ENTER button to display
the MEMORY LOAD menu.
(If any setting is not saved in the
MEMORY SAVE menu, the
MEMORY LOAD menu will not be
displayed.)
M E M O R Y
LOAD
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
Projecting sRGBcompatible pictures
sRGB is an international color
reproduction standard (IEC61966-21) established by the International
Electrotechnical Commission (IEC).
If you would like the colours in
sRGB-compatible pictures to be
reproduced more faithfully, make
the following settings.
# Press the F or G button to
select “PICTURE MODE”, and
then use the I or H button to
select “NATURAL”.
$ Press the NORMAL button on
the remote control unit.
% Select the LAMP POWER item
in the OPTION menu by
pressing the F or G buttons
and set to “HIGH” by pressing
the I or H buttons.
NOTE:
B sRGB is only enabled when RGB
signals are being input .
Basic Operation
When adjusting the black or neutral
color area of the picture, adjust it
using BRIGHT R or BRIGHT B.
A setting saved in the MEMORY
SAVE menu can be retrieved using
MEMORY LOAD. Select the
number which you wish to retrieve
by pressing the F or G buttons and
then press the ENTER button.
NOTE:
B The MEMORY LOAD menu can
also be displayed by pressing the
MEMORY USER button.
B The number with which some
settings are saved using
MEMORY SAVE will only be
displayed in the MEMORY LOAD
menu.
37
WHITE BALANCE R/G/B
(PC only)
This is used to adjust the white
areas of the picture if they appear
colourised.
Press the I button to make the
selected color lighter.
Press the H button to make the
selected color stronger.
SIGNAL MODE
(PC/DVI/YPBPR only)
This displays the type of signal
which is currently being projected.
Refer to the table on page 61 for
details on each type of signal.
GAMMA ADJUST
(PT-L300U only)
Press the ENTER button to display
the GAMMA ADJUST menu.
G A M M A
ADJUST
WHITE LEVELS
0
BLACK LEVELS
0
SELECT
ENTER
ESC
WHITE LEVELS
This is used for correcting the
gradation of a bright projected
image. To correct a white jump in
the picture, press the I buttons. To
raise the contrast ratio, press the H
buttons.
BLACK LEVELS
This is used for correcting gradation
of a dark projected image.
To correct black crushing, press the
H buttons. To raise the contrast
ratio, press the I buttons.
MEMORY SAVE
Press the ENTER button to display
the MEMORY SAVE menu.
36
M E M O R Y
SAVE
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
Up to 3 settings can be saved in the
PICTURE menu.
Select the number in which you
wish to save the setting by pressing
the F or G buttons and then press
the ENTER button.
The confirmation screen will then be
displayed. Select “OK” by pressing
the I or H buttons and press the
ENTER button.
MEMORY SAVE
OK
CANCEL
MEMORY LOAD
Press the ENTER button to display
the MEMORY LOAD menu.
(If any setting is not saved in the
MEMORY SAVE menu, the
MEMORY LOAD menu will not be
displayed.)
M E M O R Y
LOAD
MEMORY 1
MEMORY 2
MEMORY 3
SELECT
ENTER
ESC
Projecting sRGBcompatible pictures
sRGB is an international color
reproduction standard (IEC61966-21) established by the International
Electrotechnical Commission (IEC).
If you would like the colours in
sRGB-compatible pictures to be
reproduced more faithfully, make
the following settings.
# Press the F or G button to
select “PICTURE MODE”, and
then use the I or H button to
select “NATURAL”.
$ Press the NORMAL button on
the remote control unit.
% Select the LAMP POWER item
in the OPTION menu by
pressing the F or G buttons
and set to “HIGH” by pressing
the I or H buttons.
NOTE:
B sRGB is only enabled when RGB
signals are being input .
Basic Operation
When adjusting the black or neutral
color area of the picture, adjust it
using BRIGHT R or BRIGHT B.
A setting saved in the MEMORY
SAVE menu can be retrieved using
MEMORY LOAD. Select the
number which you wish to retrieve
by pressing the F or G buttons and
then press the ENTER button.
NOTE:
B The MEMORY LOAD menu can
also be displayed by pressing the
MEMORY USER button.
B The number with which some
settings are saved using
MEMORY SAVE will only be
displayed in the MEMORY LOAD
menu.
37
Adjusting the position
When an S-VIDEO/VIDEO/
YPBPR /DVI signal is being input or
SD CARD is selected.
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
B “ASPECT” can be adjusted only
when a DVI signal is being input
or when “SD CARD” is selected.
When an PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
HORIZONTAL POSITION
(S-VIDEO/VIDEO/YPBPR/PC only)
Press the I button to move the
picture to the left, and press the H
button to move the picture to the
right.
38
(S-VIDEO/VIDEO/YPBPR/PC only)
Press the I button to move the
picture down, and press the H
button to move the picture up.
AUTO SETUP
(PC only)
HORIZONTAL POSITION,
VERTICAL POSITION, DOT
CLOCK and CLOCK PHASE are
matched to the input signal and are
automatically adjusted.
NOTE:
B When the ASPECT is set to VSCROLL (page 30), AUTO
SETUP cannot be performed.
DOT CLOCK
(PC only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, use the
I and H buttons to adjust so that
any such noise is minimised.
CLOCK PHASE
(PC only)
Adjust the DOT CLOCK setting first
before carrying out this adjustment.
Use the I and H buttons to adjust
so that the noise level is least
noticeable.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or higher
are being input, interference may
not be completely eliminated
when the DOT CLOCK and
CLOCK PHASE adjustments are
carried out.
Option settings
Use the F and G buttons to select
an item, then press the I or H
buttons to change the setting.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
ON
[
OFF
ON
OFF
PC PRIORITY
(PC only)
PC PRIORITY
NORMAL
[
WIDE
NORMAL displays the PC screen
data in a 4:3 aspect ratio.
WIDE displays the PC screen data
in a 16:9 aspect ratio.
BACK COLOR
OSD
OSD
Reduction) feature, set it to “OFF”.
Basic Operation
Use the F and G buttons to select
an item, and then use the I and H
buttons to change the setting for
that item.
For items with bar scales, press the
ENTER button or the I or H
buttons to display the adjustment
screen, and then use the I or H
buttons to make the adjustment.
VERTICAL POSITION
Refer page 30.
The signal name is
displayed in the top-right
corner of the screen when
the input signal is
changed.
Use this setting when you
do not want the signal
name to be displayed.
BACK COLOR
BLACK
[
BLUE
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
This sets the background color for
the left/right margins when the 4:3
aspect ratio is selected. (Refer to
page 31.)
NR (Noise Reduction)
(S-VIDEO/VIDEO/YPBPR only)
NR
ON
[
OFF
If noise occurs from the projector
because of a poor input signal, set
NR to “ON”.
To turn off the NR (Noise
39
Advanced Operation
When the input signal is from a
PC, first select AUTO SETUP and
then press the ENTER button to
initiate automatic positioning.
If the optimum setting is not
obtained when AUTO SETUP is
carried out, adjust by the following
procedure.
ASPECT
Adjusting the position
When an S-VIDEO/VIDEO/
YPBPR /DVI signal is being input or
SD CARD is selected.
POSITION
H-POSITION
0
V-POSITION
0
ASPECT
16:9
SELECT
ENTER
ESC
B “ASPECT” can be adjusted only
when a DVI signal is being input
or when “SD CARD” is selected.
When an PC signal is being input
POSITION
H-POSITION
0
V-POSITION
0
DOT CLOCK
0
CLOCK PHASE
0
ASPECT
4:3
AUTO SETUP
SELECT
ENTER
ESC
HORIZONTAL POSITION
(S-VIDEO/VIDEO/YPBPR/PC only)
Press the I button to move the
picture to the left, and press the H
button to move the picture to the
right.
38
(S-VIDEO/VIDEO/YPBPR/PC only)
Press the I button to move the
picture down, and press the H
button to move the picture up.
AUTO SETUP
(PC only)
HORIZONTAL POSITION,
VERTICAL POSITION, DOT
CLOCK and CLOCK PHASE are
matched to the input signal and are
automatically adjusted.
NOTE:
B When the ASPECT is set to VSCROLL (page 30), AUTO
SETUP cannot be performed.
DOT CLOCK
(PC only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, use the
I and H buttons to adjust so that
any such noise is minimised.
CLOCK PHASE
(PC only)
Adjust the DOT CLOCK setting first
before carrying out this adjustment.
Use the I and H buttons to adjust
so that the noise level is least
noticeable.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or higher
are being input, interference may
not be completely eliminated
when the DOT CLOCK and
CLOCK PHASE adjustments are
carried out.
Option settings
Use the F and G buttons to select
an item, then press the I or H
buttons to change the setting.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
5H
SELECT
ADJ
ESC
ON
[
OFF
ON
OFF
PC PRIORITY
(PC only)
PC PRIORITY
NORMAL
[
WIDE
NORMAL displays the PC screen
data in a 4:3 aspect ratio.
WIDE displays the PC screen data
in a 16:9 aspect ratio.
BACK COLOR
OSD
OSD
Reduction) feature, set it to “OFF”.
Basic Operation
Use the F and G buttons to select
an item, and then use the I and H
buttons to change the setting for
that item.
For items with bar scales, press the
ENTER button or the I or H
buttons to display the adjustment
screen, and then use the I or H
buttons to make the adjustment.
VERTICAL POSITION
Refer page 30.
The signal name is
displayed in the top-right
corner of the screen when
the input signal is
changed.
Use this setting when you
do not want the signal
name to be displayed.
BACK COLOR
BLACK
[
BLUE
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
This sets the background color for
the left/right margins when the 4:3
aspect ratio is selected. (Refer to
page 31.)
NR (Noise Reduction)
(S-VIDEO/VIDEO/YPBPR only)
NR
ON
[
OFF
If noise occurs from the projector
because of a poor input signal, set
NR to “ON”.
To turn off the NR (Noise
39
Advanced Operation
When the input signal is from a
PC, first select AUTO SETUP and
then press the ENTER button to
initiate automatic positioning.
If the optimum setting is not
obtained when AUTO SETUP is
carried out, adjust by the following
procedure.
ASPECT
elevations (above 1 400 m), set
FAN CONTROL to “HIGH”.
(4:3 aspect mode only)
4:3 H-POS
CENTER
[
RIGHT
[
What is the SD memory card (option)?
LAMP POWER
LAMP POWER
HIGH
LEFT
This sets the horizontal positioning
of the projected image when the 4:3
aspect ratio is selected. (Refer to
page 31.)
FRONT/REAR
FRONT/REAR
FRONT
[
REAR
This setting should be changed in
accordance with the projector
setting-up method.
Set to “FRONT” when using a
normal reflective screen with the
projector positioned in front of the
screen, and set to “REAR” when
using a translucent screen with the
projector positioned behind the
screen.
DESK/CEILING
DESK/CEILING
DESK
[
CEILING
This setting should be changed in
accordance with the projector
setting-up method.
Set to “DESK” when setting up the
projector on a desk or similar, and
set to “CEILING” when suspending
the projector from the ceiling using
the ceiling bracket which is sold
separately.
SD memory card
[
LOW
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced.
The LOW position is recommended
for narrow rooms where a high
picture luminance is not essential or
for watching movies.
The SD memory card is a semiconductor memory which at 24 mm x 32 mm
x 2.1 mm is about the size of a postage stamp. It is a next-generation
recording medium which can be used instead of conventional storage
devices such as MDs (mini discs), CDs (compact discs) and cassette tapes.
In addition, it allows data to be repeatedly recorded, played and erased. The
projector can be used to play computer image files, video images (still
pictures) and moving pictures using the SD memory card.
Record:
Still image data
Moving image data
Play back:
Digital
Still image data
Moving image data
camera
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used.
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the LAMP
POWER setting and the number
of times the power is turned on
and off).
Computer
16MB
Advanced Operation
4:3 H-POS
Data that can be played back
Still image data
B DCF compliant still image data (See page 64 for details on DCF
compliance.)
Moving image data
B MPEG4 movie data (audio: G.726 compliant)
However, only files in ASF format can be played back.
Note when using SD memory cards
Do not turn off the projector’s power or remove an SD memory card from the
projector while the SD memory card is in use (while the access indicator is
flashing). (See page 42.) If this is not observed, corruption of the data on the
SD memory card may occur.
FAN CONTROL
FAN CONTROL
NORMAL
[
HIGH
If using of this projector at high
40
41
elevations (above 1 400 m), set
FAN CONTROL to “HIGH”.
(4:3 aspect mode only)
4:3 H-POS
CENTER
[
RIGHT
[
What is the SD memory card (option)?
LAMP POWER
LAMP POWER
HIGH
LEFT
This sets the horizontal positioning
of the projected image when the 4:3
aspect ratio is selected. (Refer to
page 31.)
FRONT/REAR
FRONT/REAR
FRONT
[
REAR
This setting should be changed in
accordance with the projector
setting-up method.
Set to “FRONT” when using a
normal reflective screen with the
projector positioned in front of the
screen, and set to “REAR” when
using a translucent screen with the
projector positioned behind the
screen.
DESK/CEILING
DESK/CEILING
DESK
[
CEILING
This setting should be changed in
accordance with the projector
setting-up method.
Set to “DESK” when setting up the
projector on a desk or similar, and
set to “CEILING” when suspending
the projector from the ceiling using
the ceiling bracket which is sold
separately.
SD memory card
[
LOW
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced.
The LOW position is recommended
for narrow rooms where a high
picture luminance is not essential or
for watching movies.
The SD memory card is a semiconductor memory which at 24 mm x 32 mm
x 2.1 mm is about the size of a postage stamp. It is a next-generation
recording medium which can be used instead of conventional storage
devices such as MDs (mini discs), CDs (compact discs) and cassette tapes.
In addition, it allows data to be repeatedly recorded, played and erased. The
projector can be used to play computer image files, video images (still
pictures) and moving pictures using the SD memory card.
Record:
Still image data
Moving image data
Play back:
Digital
Still image data
Moving image data
camera
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used.
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the LAMP
POWER setting and the number
of times the power is turned on
and off).
Computer
16MB
Advanced Operation
4:3 H-POS
Data that can be played back
Still image data
B DCF compliant still image data (See page 64 for details on DCF
compliance.)
Moving image data
B MPEG4 movie data (audio: G.726 compliant)
However, only files in ASF format can be played back.
Note when using SD memory cards
Do not turn off the projector’s power or remove an SD memory card from the
projector while the SD memory card is in use (while the access indicator is
flashing). (See page 42.) If this is not observed, corruption of the data on the
SD memory card may occur.
FAN CONTROL
FAN CONTROL
NORMAL
[
HIGH
If using of this projector at high
40
41
Inserting and removing the SD memory card
About the SD menu
Inserting the SD
memory card
Removing the SD
memory card
The still image data and moving image data that is stored on SD memory
cards can be played back using the SD menu.
Insert the SD memory card so that it
is facing the correct way.
# Open the slot cover at the side
of the projector.
# Open the slot cover.
$ Check that the access indicator
at the upper-left corner of the
card slot is not flashing (the SD
memory card is not being
accessed).
Access lamp
Displaying the SD menu
Press the SD button to change the display to the SD CARD screen.
PICTURE (page 44)
This lets you play back still image
data.
PICTURE
SLIDE SHOW
SLIDE SHOW (page 45)
This lets you play back still image
data in a certain order.
VIDEO
NOTE:
B If you try to force the SD memory
card to go in the wrong way, it
may damage the SD memory
card and the card slot.
% Close the slot cover.
NOTE:
B Always be sure to check that the
access indicator is not flashing
before removing the SD memory
card. If the SD memory card is
removed while the access
indicator is flashing, the data
stored on the SD memory card
may become corrupted.
% Push in the middle of the SD
memory card. (The SD memory
card will protrude slightly.)
& Remove the card.
VIDEO (page 49)
This lets you play back moving
image data.
B If the SD menu is not displayed when the SD button is pressed,
—press the SD MENU button repeatedly until it is displayed or
—the previous menu screen or image on an SD CARD screen may be
displayed or played back.
NOTE:
B When the SD CARD screen is selected, the SD MENU button can be used
to return to a previous screen (up to the SD menu shown above).
' Close the slot cover.
42
43
Advanced Operation
$ Insert the SD memory card as
shown in the illustration below.
Insert the SD memory card with
the label side facing upward and
so that the cut-away corner is
inserted first. Push the SD
memory card in as far as it will
go.
Inserting and removing the SD memory card
About the SD menu
Inserting the SD
memory card
Removing the SD
memory card
The still image data and moving image data that is stored on SD memory
cards can be played back using the SD menu.
Insert the SD memory card so that it
is facing the correct way.
# Open the slot cover at the side
of the projector.
# Open the slot cover.
$ Check that the access indicator
at the upper-left corner of the
card slot is not flashing (the SD
memory card is not being
accessed).
Access lamp
Displaying the SD menu
Press the SD button to change the display to the SD CARD screen.
PICTURE (page 44)
This lets you play back still image
data.
PICTURE
SLIDE SHOW
SLIDE SHOW (page 45)
This lets you play back still image
data in a certain order.
VIDEO
NOTE:
B If you try to force the SD memory
card to go in the wrong way, it
may damage the SD memory
card and the card slot.
% Close the slot cover.
NOTE:
B Always be sure to check that the
access indicator is not flashing
before removing the SD memory
card. If the SD memory card is
removed while the access
indicator is flashing, the data
stored on the SD memory card
may become corrupted.
% Push in the middle of the SD
memory card. (The SD memory
card will protrude slightly.)
& Remove the card.
VIDEO (page 49)
This lets you play back moving
image data.
B If the SD menu is not displayed when the SD button is pressed,
—press the SD MENU button repeatedly until it is displayed or
—the previous menu screen or image on an SD CARD screen may be
displayed or played back.
NOTE:
B When the SD CARD screen is selected, the SD MENU button can be used
to return to a previous screen (up to the SD menu shown above).
' Close the slot cover.
42
43
Advanced Operation
$ Insert the SD memory card as
shown in the illustration below.
Insert the SD memory card with
the label side facing upward and
so that the cut-away corner is
inserted first. Push the SD
memory card in as far as it will
go.
Playing back still images
Slide playback of still images
The PICTURE option lets you play back still image data.
“SLIDE SHOW” lets you play back still images in a certain order using one of
three available playback methods. Use the F and G buttons to select an
item, and then press the ENTER button. Use the I and H buttons to change
the setting for the selected item.
% Use the F, G, I and H
buttons to select the still image
to be enlarged, and then press
the ENTER button.
PICTURE
Use the F and G buttons to
select “SLIDE SHOW”, and then
press the ENTER button.
SLIDE SHOW
PICTURE
VIDEO
SLIDE SHOW
B If there is no still image data that
can be played back, the following
screen is not displayed.
$ Use the F and G buttons to
select the folder that contains
the still image data that you
would like to play back, and
then press the ENTER button.
100-0001
1/11
(C)
(D)
(C)File name of selected still
image
(D)Number of selected still
image/Total number of still images
B If there are 10 or more still images
in a folder, use the F and G
buttons to scroll through the pages.
VIDEO
The still image that will be the first
image to be played back for the
selected item will be displayed.
SELECT ITEM
100
1/3
(A)
(B)
(A)Number of selected folder
(B)Folder number/Total number
of folders
B Up to a maximum of three still
images that are saved in the
folder can be displayed in a
single row. If there are four or
more folders, use the F and G
buttons to scroll through the
pages.
44
SETTING
ALL FILE
FOLDER
USER
<Button functions during still image playback>
B Play back next image ... H button
B Play back previous image
.................................... I button
B Rotate images
....................... F and G buttons
B Return to still image selection
screen .......... SD MENU button
100
SETTING (page 46)
This lets you set whether the slide
playback is to be automatically
continuous (automatic playback) or
whether it can be switched manually
(manual playback), and also lets
you edit the user settings for
“USER”.
ALL FILE
If you press the ENTER button,
all still images that are stored on
the SD memory card are played
back in order.
FOLDER
If you use the I and H buttons to
select the folder to be played back
and then press the ENTER button,
all still images in the selected
folder are played back in order.
USER
If the user selects the desired still
images, the still images that were
selected by the user can be played
back in order. When using user
playback, you must select the still
images to be played back using the
“USER” command in the
“SETTING” screen. When “USER”
is selected, use the I and H
buttons to select the user settings,
and then press the ENTER button
to start user playback.
<Button functions during slide playback>
B Pause/cancel automatic
playback ....... ENTER button
The following buttons can be
used while manual playback or
automatic playback is paused.
B Play back next image
................................ H button
B Play back previous image
.................................I button
B Rotate images
................... F and G buttons
B Return to still image selection
screen ........ SD MENU button
45
Advanced Operation
# Use the F and G buttons to
select “PICTURE”, and then
press the ENTER button.
Playing back still images
Slide playback of still images
The PICTURE option lets you play back still image data.
“SLIDE SHOW” lets you play back still images in a certain order using one of
three available playback methods. Use the F and G buttons to select an
item, and then press the ENTER button. Use the I and H buttons to change
the setting for the selected item.
% Use the F, G, I and H
buttons to select the still image
to be enlarged, and then press
the ENTER button.
PICTURE
Use the F and G buttons to
select “SLIDE SHOW”, and then
press the ENTER button.
SLIDE SHOW
PICTURE
VIDEO
SLIDE SHOW
B If there is no still image data that
can be played back, the following
screen is not displayed.
$ Use the F and G buttons to
select the folder that contains
the still image data that you
would like to play back, and
then press the ENTER button.
100-0001
1/11
(C)
(D)
(C)File name of selected still
image
(D)Number of selected still
image/Total number of still images
B If there are 10 or more still images
in a folder, use the F and G
buttons to scroll through the pages.
VIDEO
The still image that will be the first
image to be played back for the
selected item will be displayed.
SELECT ITEM
100
1/3
(A)
(B)
(A)Number of selected folder
(B)Folder number/Total number
of folders
B Up to a maximum of three still
images that are saved in the
folder can be displayed in a
single row. If there are four or
more folders, use the F and G
buttons to scroll through the
pages.
44
SETTING
ALL FILE
FOLDER
USER
<Button functions during still image playback>
B Play back next image ... H button
B Play back previous image
.................................... I button
B Rotate images
....................... F and G buttons
B Return to still image selection
screen .......... SD MENU button
100
SETTING (page 46)
This lets you set whether the slide
playback is to be automatically
continuous (automatic playback) or
whether it can be switched manually
(manual playback), and also lets
you edit the user settings for
“USER”.
ALL FILE
If you press the ENTER button,
all still images that are stored on
the SD memory card are played
back in order.
FOLDER
If you use the I and H buttons to
select the folder to be played back
and then press the ENTER button,
all still images in the selected
folder are played back in order.
USER
If the user selects the desired still
images, the still images that were
selected by the user can be played
back in order. When using user
playback, you must select the still
images to be played back using the
“USER” command in the
“SETTING” screen. When “USER”
is selected, use the I and H
buttons to select the user settings,
and then press the ENTER button
to start user playback.
<Button functions during slide playback>
B Pause/cancel automatic
playback ....... ENTER button
The following buttons can be
used while manual playback or
automatic playback is paused.
B Play back next image
................................ H button
B Play back previous image
.................................I button
B Rotate images
................... F and G buttons
B Return to still image selection
screen ........ SD MENU button
45
Advanced Operation
# Use the F and G buttons to
select “PICTURE”, and then
press the ENTER button.
AUTO MODE
The still images are played back
automatically in order according to
the following setting.
SETTING1
AUTO MODE
SETTING2
MANUAL MODE
USER SET NEW
USER SET
If adding settings for a new user, use the
I and H buttons to select “NEW” and
then press the ENTER button. The user
setting edit screen will then be displayed.
If you would like to change the settings
for an existing user, use the I and H
buttons to select the user setting file (0 9) that you would like to change, and
then press the ENTER button.
User setting edit screen
(A)
(B)
,
1,0
,
100-0001
1/11
(C)
(D)
(E)
(A)Still images set by user (this
row is blank for new users)
(B)Still images that are available
for setting by the user
(C)Playback time and rotation
angle for selected still image
(D)File name of selected still
image
(E)Number of selected still
image/Total number of still images
See the next page for details on
how to edit user settings.
46
REPEAT
1
INTERVAL
1
“REPEAT”
ENTER button
Use the I and H buttons to select
how many times automatic playback
is to be repeated.
“INTERVAL”
Use the I and H buttons to select
the time interval (seconds) between
playback of each still image.
Editing user settings
You can use the user setting edit
screen that is displayed when you
select “SETTING” during slide
playback on the previous page to add,
move and delete still images from the
list of images for slide playback and
also to change playback settings.
Adding and moving images
You can select still images that are
saved on the SD memory card and add
them to the user settings, and also
change the order of the still images
that have been selected in the user
settings.
# Use the F, G, I and H buttons
to select the still images to be
added or moved, and then press
the ENTER button.
* Once you have made the required
settings, press the ENTER button.
MANUAL MODE
During slide playback, press the I
button to play back the next still
image, and press the H button to
play back the previous still image.
NOTE:
B When editing the user settings,
slide playback settings that
have not been created using
this projector cannot be edited.
% Use the F, G, I and H buttons
to move the cursor (|) to the
place where the image is to be
added or moved, and then press
the ENTER button.
1,0
,
100-0001
1/11
Repeat the procedure from step # to
add or move additional images.
1,0
,
100-0001
1/11
B When moving images, only
images that have already been
added to the user settings can be
moved.
$ Select “ADD” or “MOVE” and
then press the ENTER button.
See the following page for
details on how to change
settings and delete images.
EDIT
SETTING
ADD
MOVE
DELETE
47
Advanced Operation
SETTING
AUTO MODE
The still images are played back
automatically in order according to
the following setting.
SETTING1
AUTO MODE
SETTING2
MANUAL MODE
USER SET NEW
USER SET
If adding settings for a new user, use the
I and H buttons to select “NEW” and
then press the ENTER button. The user
setting edit screen will then be displayed.
If you would like to change the settings
for an existing user, use the I and H
buttons to select the user setting file (0 9) that you would like to change, and
then press the ENTER button.
User setting edit screen
(A)
(B)
,
1,0
,
100-0001
1/11
(C)
(D)
(E)
(A)Still images set by user (this
row is blank for new users)
(B)Still images that are available
for setting by the user
(C)Playback time and rotation
angle for selected still image
(D)File name of selected still
image
(E)Number of selected still
image/Total number of still images
See the next page for details on
how to edit user settings.
46
REPEAT
1
INTERVAL
1
“REPEAT”
ENTER button
Use the I and H buttons to select
how many times automatic playback
is to be repeated.
“INTERVAL”
Use the I and H buttons to select
the time interval (seconds) between
playback of each still image.
Editing user settings
You can use the user setting edit
screen that is displayed when you
select “SETTING” during slide
playback on the previous page to add,
move and delete still images from the
list of images for slide playback and
also to change playback settings.
Adding and moving images
You can select still images that are
saved on the SD memory card and add
them to the user settings, and also
change the order of the still images
that have been selected in the user
settings.
# Use the F, G, I and H buttons
to select the still images to be
added or moved, and then press
the ENTER button.
* Once you have made the required
settings, press the ENTER button.
MANUAL MODE
During slide playback, press the I
button to play back the next still
image, and press the H button to
play back the previous still image.
NOTE:
B When editing the user settings,
slide playback settings that
have not been created using
this projector cannot be edited.
% Use the F, G, I and H buttons
to move the cursor (|) to the
place where the image is to be
added or moved, and then press
the ENTER button.
1,0
,
100-0001
1/11
Repeat the procedure from step # to
add or move additional images.
1,0
,
100-0001
1/11
B When moving images, only
images that have already been
added to the user settings can be
moved.
$ Select “ADD” or “MOVE” and
then press the ENTER button.
See the following page for
details on how to change
settings and delete images.
EDIT
SETTING
ADD
MOVE
DELETE
47
Advanced Operation
SETTING
EDIT
SETTING
ADD
MOVE
DELETE
will be played back at the interval set
for automatic playback on page 46.
B The setting screen can also be
displayed by selecting a still image and
then pressing and holding the ENTER
button for one second or more.
DELETE
This describes how to delete
images from the user settings.
# Use the F, G, I and H buttons
to select the still image to be
deleted from the user settings,
and then press the ENTER button.
$ Select “DELETE” and then
press the ENTER button.
EDIT
SETTING
ADD
MOVE
DELETE
# Use the F and G buttons to
select VIDEO and then press
the ENTER button.
PICTURE
SLIDE SHOW
VIDEO
B If there is no moving image data
that can be played back, the
following screen is not displayed.
$ Use the F and G buttons to
select the moving image data
that you would like to play
back, and then press the
ENTER button.
PLAY FILE
SETTING
INTERVAL
ROTATE
100-0001
Playing back moving images
PRL001
PRL001
PRL001
PRL001
1
0
MOL001
MOL002
MOL003
MOL004
DELETE
2002/07/01 07:00:00
“INTERVAL”
Use the I and H buttons to select
the time interval (seconds) between
playback of each still image.
“ROTATE”
Use the I and H buttons to select the
angle of rotation for the still image during
playback. This lets you correct the position
of sideways images during playback.
* Once you have made the required
settings, press the ENTER button.
NOTE:
B If no setting value for the playback
interval is displayed, the still images
48
USER FILE
100-0001
CANCEL
0
“USER FILE”
This deletes the user settings that are
currently being edited.
“100-0001”(File name of selected
still image)
This lets you delete only the selected
still image.
“CANCEL”
This cancels the delete operation.
The moving image data will then be
played back.
<Button functions during
moving image playback>
Fast-forward playback...H button
Fast-rewind playback ....I button
Play back next movie.....G button
Play back previous movie....F button
Pause/cancel pause...ENTER button
Stop playback
...Press the ENTER button for 1 second or more
Display/hide playback time
...........................SD TIME button
00:01:00
Playback time display
Select moving image file
.........................SD MENU button
If you press the I button during
movie playback, then playback will
start again from the beginning of
the current movie.
NOTE:
B Images containing fast movement
may appear to pause momentarily
(frame dropout) or they may appear
as mosaic patterns, but this is normal.
B If the projector has been used to enlarge
the images, some movie data may appear
lower in resolution, but this is normal.
B During fast-forward playback and
rewind playback, each still image
is played back in the same order.
49
Advanced Operation
SETUP
This describes how to set the playback
interval and angle of rotation for still
images in the user settings.
# Use the F, G, I and H
buttons to select a still image
from the user settings, and
then press the ENTER button.
$ Select “SETTING” and then
press the ENTER button.
EDIT
SETTING
ADD
MOVE
DELETE
will be played back at the interval set
for automatic playback on page 46.
B The setting screen can also be
displayed by selecting a still image and
then pressing and holding the ENTER
button for one second or more.
DELETE
This describes how to delete
images from the user settings.
# Use the F, G, I and H buttons
to select the still image to be
deleted from the user settings,
and then press the ENTER button.
$ Select “DELETE” and then
press the ENTER button.
EDIT
SETTING
ADD
MOVE
DELETE
# Use the F and G buttons to
select VIDEO and then press
the ENTER button.
PICTURE
SLIDE SHOW
VIDEO
B If there is no moving image data
that can be played back, the
following screen is not displayed.
$ Use the F and G buttons to
select the moving image data
that you would like to play
back, and then press the
ENTER button.
PLAY FILE
SETTING
INTERVAL
ROTATE
100-0001
Playing back moving images
PRL001
PRL001
PRL001
PRL001
1
0
MOL001
MOL002
MOL003
MOL004
DELETE
2002/07/01 07:00:00
“INTERVAL”
Use the I and H buttons to select
the time interval (seconds) between
playback of each still image.
“ROTATE”
Use the I and H buttons to select the
angle of rotation for the still image during
playback. This lets you correct the position
of sideways images during playback.
* Once you have made the required
settings, press the ENTER button.
NOTE:
B If no setting value for the playback
interval is displayed, the still images
48
USER FILE
100-0001
CANCEL
0
“USER FILE”
This deletes the user settings that are
currently being edited.
“100-0001”(File name of selected
still image)
This lets you delete only the selected
still image.
“CANCEL”
This cancels the delete operation.
The moving image data will then be
played back.
<Button functions during
moving image playback>
Fast-forward playback...H button
Fast-rewind playback ....I button
Play back next movie.....G button
Play back previous movie....F button
Pause/cancel pause...ENTER button
Stop playback
...Press the ENTER button for 1 second or more
Display/hide playback time
...........................SD TIME button
00:01:00
Playback time display
Select moving image file
.........................SD MENU button
If you press the I button during
movie playback, then playback will
start again from the beginning of
the current movie.
NOTE:
B Images containing fast movement
may appear to pause momentarily
(frame dropout) or they may appear
as mosaic patterns, but this is normal.
B If the projector has been used to enlarge
the images, some movie data may appear
lower in resolution, but this is normal.
B During fast-forward playback and
rewind playback, each still image
is played back in the same order.
49
Advanced Operation
SETUP
This describes how to set the playback
interval and angle of rotation for still
images in the user settings.
# Use the F, G, I and H
buttons to select a still image
from the user settings, and
then press the ENTER button.
$ Select “SETTING” and then
press the ENTER button.
Error displays
Indicators
Errors may be displayed while using an SD memory card. If an error occurs,
check the following table for a description of the error.
There are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.
NO DATA
Details
B There is no SD memory card inserted.
B The SD memory card does not contain any data that
can be played back by the projector.
UNFORMAT
B The inserted card does not match the required
specifications, for example the format is different.
DATA ERROR
B The data is not compatible and cannot be played
back.
READ ERROR
B The data cannot be read from the card.
WRITE ERROR
B The data could not be saved onto the card. Check if
the SD memory card is write-protected, or if it has
enough free space available.
ERROR
B If “ERROR” is displayed instead of a thumbnail
image, it means that the image cannot be displayed
because there is no data or the data is incompatible.
?
B If “?” is displayed instead of a thumbnail image, it
means that only the thumbnail data cannot be found.
UNEXPECTED
ERROR
B An error occurred during an operation. If the problem
cannot be reset by pressing the SD MENU button,
turn off the projector’s power while referring to
“Turning off the power” on page 23, and then turn the
power back on again.
Illuminated (red)
(Lamp unit on)
The surrounding
temperature or the
temperature inside
the projector has
become unusually
Problem high.
Indicator
display
Flashing (red)
(Lamp unit on)
The temperature
inside the projector
has become
dangerously high, or
the temperature has
suddenly changed.
Flashing (red)
(Lamp unit off)
The surrounding
temperature or the
temperature inside
the projector has
become dangerously
high, causing the
lamp unit to be
automatically shut
off.
B The ventilation holes may be covered.
Possible B The ambient temperature in the place of use may be too high.
cause B The air filter may be blocked.
B Uncover the ventilation holes.
B Set up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is
between 20% and 80% (with no condensation). [If you set the
FAN CONTROL to “HIGH” (page 40), set up the projector in a
Remedy
place where the temperature is between 0 °C (32 °F) and 35 °C
(95 °F) and the humidity is between 20% and 80% (with no
condensation).]
B Turn off the MAIN POWER switch by following the procedure
on page 23, and then clean the air filter (refer to page 53).
Others
NOTE:
B Press the SD MENU button to clear an error display.
B A 2-digit error code will be displayed with an error display.
You may need the error code when asking for service.
TEMP indicator
Advanced Operation
Error display
NO CARD
50
51
Error displays
Indicators
Errors may be displayed while using an SD memory card. If an error occurs,
check the following table for a description of the error.
There are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.
NO DATA
Details
B There is no SD memory card inserted.
B The SD memory card does not contain any data that
can be played back by the projector.
UNFORMAT
B The inserted card does not match the required
specifications, for example the format is different.
DATA ERROR
B The data is not compatible and cannot be played
back.
READ ERROR
B The data cannot be read from the card.
WRITE ERROR
B The data could not be saved onto the card. Check if
the SD memory card is write-protected, or if it has
enough free space available.
ERROR
B If “ERROR” is displayed instead of a thumbnail
image, it means that the image cannot be displayed
because there is no data or the data is incompatible.
?
B If “?” is displayed instead of a thumbnail image, it
means that only the thumbnail data cannot be found.
UNEXPECTED
ERROR
B An error occurred during an operation. If the problem
cannot be reset by pressing the SD MENU button,
turn off the projector’s power while referring to
“Turning off the power” on page 23, and then turn the
power back on again.
Illuminated (red)
(Lamp unit on)
The surrounding
temperature or the
temperature inside
the projector has
become unusually
Problem high.
Indicator
display
Flashing (red)
(Lamp unit on)
The temperature
inside the projector
has become
dangerously high, or
the temperature has
suddenly changed.
Flashing (red)
(Lamp unit off)
The surrounding
temperature or the
temperature inside
the projector has
become dangerously
high, causing the
lamp unit to be
automatically shut
off.
B The ventilation holes may be covered.
Possible B The ambient temperature in the place of use may be too high.
cause B The air filter may be blocked.
B Uncover the ventilation holes.
B Set up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is
between 20% and 80% (with no condensation). [If you set the
FAN CONTROL to “HIGH” (page 40), set up the projector in a
Remedy
place where the temperature is between 0 °C (32 °F) and 35 °C
(95 °F) and the humidity is between 20% and 80% (with no
condensation).]
B Turn off the MAIN POWER switch by following the procedure
on page 23, and then clean the air filter (refer to page 53).
Others
NOTE:
B Press the SD MENU button to clear an error display.
B A 2-digit error code will be displayed with an error display.
You may need the error code when asking for service.
TEMP indicator
Advanced Operation
Error display
NO CARD
50
51
Cleaning and replacing the air filter
Indicator
display
Illuminated (red)
It is nearly time to
Problem replace the lamp
unit.
Flashing (red)
An abnormality has been detected in the lamp
circuit.
B There may be an
B Does “REPLACE B The power may
LAMP” appear on
have been turned
abnormality in the
Possible
the screen after
on straight away
lamp circuit.
cause
the projector is
after it was turned
turned on?
off.
B This occurs when B Wait for a while
B Turn off the MAIN
the operation time
until the lamp unit
POWER switch by
for the lamp unit is
cools down before
following the
nearing 1800
turning the power
procedure given
hours. (when
back on again.
on page 23, and
LAMP POWER
then contact an
has
been
set
to
Authorised
Remedy
“HIGH”) Ask your
Service Center.
dealer or an
Authorised
Service Center to
replace the lamp
unit.
NOTE:
B Be sure to turn off the MAIN POWER switch by following the procedure
given in “Turning off the power” on page 23 before carrying out any of the
procedures in the “Remedy” column.
B If the main power turns off after the TEMP indicator starts flashing, it
means that an abnormality has occurred. Please contact an Authorised
Service Center so that the necessary repairs can be made.
If the air filter becomes clogged with dust, the internal temperature of the
projector will rise, the TEMP indicator will flash and the projector power will
turn off. The air filter should be cleaned every 100 hours of use,
depending on the location where the projector is being used.
Cleaning procedure
# Turn off the MAIN POWER
switch and disconnect the
power cord plug from the wall
outlet.
Turn off the MAIN POWER switch
according to the procedure given
in “Turning off the power” on
page 23 before disconnecting the
plug from the wall outlet.
$ Gently turn the projector
upside down.
NOTE:
B Place the projector on top of a
soft cloth so that it will not
become scratched.
% Remove the air filter.
Put your fingernails under the air
filter and pull the air filter out of
the projector.
& Clean the air filter.
Use a vacuum cleaner to clean
off any accumulated dust.
NOTE:
B Be careful not to let the air filter
get sucked into the vacuum
cleaner.
' Install the air filter.
NOTE:
B Be sure to install the air filter
cover before using the projector.
If the projector is used without the
air filter cover installed, dust and
other foreign particles will be
drawn into the projector, and
malfunctions will result.
B If the dust cannot be removed by
cleaning, it is time to replace the
air filter. Please consult your
dealer. Furthermore, if the lamp
unit is being replaced, replace the
air filter at this time also.
Air filter
52
53
Others
LAMP indicator
Cleaning and replacing the air filter
Indicator
display
Illuminated (red)
It is nearly time to
Problem replace the lamp
unit.
Flashing (red)
An abnormality has been detected in the lamp
circuit.
B There may be an
B Does “REPLACE B The power may
LAMP” appear on
have been turned
abnormality in the
Possible
the screen after
on straight away
lamp circuit.
cause
the projector is
after it was turned
turned on?
off.
B This occurs when B Wait for a while
B Turn off the MAIN
the operation time
until the lamp unit
POWER switch by
for the lamp unit is
cools down before
following the
nearing 1800
turning the power
procedure given
hours. (when
back on again.
on page 23, and
LAMP POWER
then contact an
has
been
set
to
Authorised
Remedy
“HIGH”) Ask your
Service Center.
dealer or an
Authorised
Service Center to
replace the lamp
unit.
NOTE:
B Be sure to turn off the MAIN POWER switch by following the procedure
given in “Turning off the power” on page 23 before carrying out any of the
procedures in the “Remedy” column.
B If the main power turns off after the TEMP indicator starts flashing, it
means that an abnormality has occurred. Please contact an Authorised
Service Center so that the necessary repairs can be made.
If the air filter becomes clogged with dust, the internal temperature of the
projector will rise, the TEMP indicator will flash and the projector power will
turn off. The air filter should be cleaned every 100 hours of use,
depending on the location where the projector is being used.
Cleaning procedure
# Turn off the MAIN POWER
switch and disconnect the
power cord plug from the wall
outlet.
Turn off the MAIN POWER switch
according to the procedure given
in “Turning off the power” on
page 23 before disconnecting the
plug from the wall outlet.
$ Gently turn the projector
upside down.
NOTE:
B Place the projector on top of a
soft cloth so that it will not
become scratched.
% Remove the air filter.
Put your fingernails under the air
filter and pull the air filter out of
the projector.
& Clean the air filter.
Use a vacuum cleaner to clean
off any accumulated dust.
NOTE:
B Be careful not to let the air filter
get sucked into the vacuum
cleaner.
' Install the air filter.
NOTE:
B Be sure to install the air filter
cover before using the projector.
If the projector is used without the
air filter cover installed, dust and
other foreign particles will be
drawn into the projector, and
malfunctions will result.
B If the dust cannot be removed by
cleaning, it is time to replace the
air filter. Please consult your
dealer. Furthermore, if the lamp
unit is being replaced, replace the
air filter at this time also.
Air filter
52
53
Others
LAMP indicator
Replacing the lamp unit
The lamp unit should only be
replaced by a qualified
technician.
When replacing the lamp, allow it
to cool for at least one hour
before handling it.
B The lamp cover gets very hot,
and contact with it can cause
burns.
Notes on replacing the
lamp unit
B The light generating lamp is
made of glass, so dropping it or
allowing it to hit hard objects may
cause it to burst. Be careful when
handling the lamp.
B After having removed the old
lamp, carelessly discarding it can
cause the lamp to burst. Dispose
of the lamp with the same care
that would be taken with a
fluorescent light.
B A Phillips screwdriver is
necessary for removing the lamp
unit. Make sure that your hands
are not slippery when using the
screwdriver.
NOTE:
B The projector is not supplied with
a replacement lamp unit. Please
ask your dealer for details. Lamp
unit product no.: ET-LAE100
CAUTION:
B Do not use any lamp unit other
than the one with the product
number indicated above.
Lamp unit replacement
period
The lamp is a consumable product.
Even when the full life of the bulb
has not been exhausted, the
brightness of the light will gradually
decline. Therefore periodic
replacement of the lamp is
necessary.
The intended lamp replacement
interval is 2000 hours, but it is
possible that the lamp may need to
be replaced earlier due to variables
such as a particular lamp's
characteristics, usage conditions
and the installation environment.
Early preparation for lamp
replacement is encouraged.
A lamp that has exceeded 2000
hours of use has a much greater
chance of exploding. In order to
prevent the lamp from exploding,
the lamp will be automatically shut
off when 2000 hours of use have
been reached.
NOTE:
B The usage hours explained
above are for use when the HIGH
setting has been selected for
LAMP POWER in the OPTION
menu. If the LOW setting is
selected, the brightness of the
lamp will be less and life of the
lamp can be extended.
B While 2000 hours is the intended
replacement interval, it is not a
period of time covered by
warranty.
More than 1800 hours
More than 2000 hours
(The lamp will turn off
automatically about 10
minutes after turning on
the power.)
Displayed for 30
seconds. Pressing any
button will clear the
display.
The lamp indicator
illuminates red even if
This display cannot be the projector is in
cleared at all, no matter standby mode.
which button is pressed.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 2000 hours (when LAMP POWER has
been set to “HIGH”), the projector will switch to standby mode after
approximately 10 minutes of operation. The steps * to - on the next
page should thus be completed within 10 minutes.
# Turn off the MAIN POWER
switch according to the
procedure given in “Turning off
the power” on page 23, and
then disconnect the power
cord plug from the wall outlet
and check that the area around
the lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover from the
projector.
Lamp unit cover
% Use a Phillips screwdriver to loosen
the two lamp unit fixing screws until
the screws turn freely. Then hold
the handle of the lamp unit and
gently pull it out from the projector.
Lamp unit fixing screws
Handle
Lamp unit cover
fixing screws
54
Lamp indicator warning
light
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
55
Others
Warning
On-screen display
Replacing the lamp unit
The lamp unit should only be
replaced by a qualified
technician.
When replacing the lamp, allow it
to cool for at least one hour
before handling it.
B The lamp cover gets very hot,
and contact with it can cause
burns.
Notes on replacing the
lamp unit
B The light generating lamp is
made of glass, so dropping it or
allowing it to hit hard objects may
cause it to burst. Be careful when
handling the lamp.
B After having removed the old
lamp, carelessly discarding it can
cause the lamp to burst. Dispose
of the lamp with the same care
that would be taken with a
fluorescent light.
B A Phillips screwdriver is
necessary for removing the lamp
unit. Make sure that your hands
are not slippery when using the
screwdriver.
NOTE:
B The projector is not supplied with
a replacement lamp unit. Please
ask your dealer for details. Lamp
unit product no.: ET-LAE100
CAUTION:
B Do not use any lamp unit other
than the one with the product
number indicated above.
Lamp unit replacement
period
The lamp is a consumable product.
Even when the full life of the bulb
has not been exhausted, the
brightness of the light will gradually
decline. Therefore periodic
replacement of the lamp is
necessary.
The intended lamp replacement
interval is 2000 hours, but it is
possible that the lamp may need to
be replaced earlier due to variables
such as a particular lamp's
characteristics, usage conditions
and the installation environment.
Early preparation for lamp
replacement is encouraged.
A lamp that has exceeded 2000
hours of use has a much greater
chance of exploding. In order to
prevent the lamp from exploding,
the lamp will be automatically shut
off when 2000 hours of use have
been reached.
NOTE:
B The usage hours explained
above are for use when the HIGH
setting has been selected for
LAMP POWER in the OPTION
menu. If the LOW setting is
selected, the brightness of the
lamp will be less and life of the
lamp can be extended.
B While 2000 hours is the intended
replacement interval, it is not a
period of time covered by
warranty.
More than 1800 hours
More than 2000 hours
(The lamp will turn off
automatically about 10
minutes after turning on
the power.)
Displayed for 30
seconds. Pressing any
button will clear the
display.
The lamp indicator
illuminates red even if
This display cannot be the projector is in
cleared at all, no matter standby mode.
which button is pressed.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 2000 hours (when LAMP POWER has
been set to “HIGH”), the projector will switch to standby mode after
approximately 10 minutes of operation. The steps * to - on the next
page should thus be completed within 10 minutes.
# Turn off the MAIN POWER
switch according to the
procedure given in “Turning off
the power” on page 23, and
then disconnect the power
cord plug from the wall outlet
and check that the area around
the lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover from the
projector.
Lamp unit cover
% Use a Phillips screwdriver to loosen
the two lamp unit fixing screws until
the screws turn freely. Then hold
the handle of the lamp unit and
gently pull it out from the projector.
Lamp unit fixing screws
Handle
Lamp unit cover
fixing screws
54
Lamp indicator warning
light
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
55
Others
Warning
On-screen display
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
56
+ Press the ENTER button to
display the OPTION screen,
and then use the F and G
buttons to select LAMP
RUNTIME.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
1820H
SELECT
ADJ
ESC
, Press and hold the ENTER
button for approximately 3
seconds.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
TIME RESET [POWER OFF]
SELECT
ADJ
ESC
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
NOTE:
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 23 for details on
how to turn off the power.
Before calling for service
Before asking for service, check the following points.
Problem
Power does not
turn on.
Possible cause
B The power cord may not be connected.
B The MAIN POWER switch is turned off.
B The main power supply is not being supplied to the
wall outlet.
B TEMP indicator is illuminated or flashing. (Refer to
page 51.)
B LAMP indicator is illuminated or flashing. (Refer to
page 52.)
B The lamp unit cover has not been securely
installed.
No picture appears. B The video signal input source may not be
connected properly.
B The input selection setting may not be correct.
(Refer to page 22.)
B The BRIGHT adjustment setting may be at the
minimum possible setting. (Refer to page 34.)
B The shutter function may be in use. (Refer to page
33.)
The picture is
B The lens cover may still be attached to the lens.
fuzzy.
B The lens focus may not have been set correctly.
(Refer to page 23.)
B The projector may not be at the correct distance
from the screen. (Refer to page 21.)
B The lens may be dirty.
B The projector may be tilted too much. (Refer to
page 23.)
COLOR is too light or B COLOR or TINT adjustment may be incorrect.
TINT is poor
(Refer to pages 34 and 35.)
B The input source which is connected to the
projector may not be adjusted correctly.
No sound can be
B The audio signal source may not be connected
heard.
properly.
B The volume adjustment may be at the lowest
possible setting. (Refer to page 15.)
B Make sure that the MUTE function is not activated.
(Refer to page 33.)
EXIT
57
Others
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection circuit
to operate so that the power
cannot be turned on.
( Insert the power cord plug into
the wall outlet and then press
the MAIN POWER switch.
NOTE:
B If the POWER button on the
projector does not illuminate red
when the MAIN POWER switch is
turned on, turn the MAIN POWER
switch off again and check that
the lamp unit and the lamp unit
cover are securely installed. Then
turn the MAIN POWER switch
back on.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the MAIN MENU
screen, and then press the F
and G buttons to move the
cursor to select “OPTION”.
M E N U
KEYSTONE
PICTURE
POSITION
SHUTTER
VOLUME
LANGUAGE
OPTION
SD MENU
SELECT
ENTER
56
+ Press the ENTER button to
display the OPTION screen,
and then use the F and G
buttons to select LAMP
RUNTIME.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
LAMP RUNTIME
1820H
SELECT
ADJ
ESC
, Press and hold the ENTER
button for approximately 3
seconds.
OPTION
OSD
ON
NR
ON
PC PRIORITY
NORMAL
BACK COLOR
BLACK
4:3 H-POS
CENTER
FRONT/REAR
FRONT
DESK/CEILING
DESK
FAN CONTROL
NORMAL
LAMP POWER
HIGH
TIME RESET [POWER OFF]
SELECT
ADJ
ESC
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
NOTE:
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 23 for details on
how to turn off the power.
Before calling for service
Before asking for service, check the following points.
Problem
Power does not
turn on.
Possible cause
B The power cord may not be connected.
B The MAIN POWER switch is turned off.
B The main power supply is not being supplied to the
wall outlet.
B TEMP indicator is illuminated or flashing. (Refer to
page 51.)
B LAMP indicator is illuminated or flashing. (Refer to
page 52.)
B The lamp unit cover has not been securely
installed.
No picture appears. B The video signal input source may not be
connected properly.
B The input selection setting may not be correct.
(Refer to page 22.)
B The BRIGHT adjustment setting may be at the
minimum possible setting. (Refer to page 34.)
B The shutter function may be in use. (Refer to page
33.)
The picture is
B The lens cover may still be attached to the lens.
fuzzy.
B The lens focus may not have been set correctly.
(Refer to page 23.)
B The projector may not be at the correct distance
from the screen. (Refer to page 21.)
B The lens may be dirty.
B The projector may be tilted too much. (Refer to
page 23.)
COLOR is too light or B COLOR or TINT adjustment may be incorrect.
TINT is poor
(Refer to pages 34 and 35.)
B The input source which is connected to the
projector may not be adjusted correctly.
No sound can be
B The audio signal source may not be connected
heard.
properly.
B The volume adjustment may be at the lowest
possible setting. (Refer to page 15.)
B Make sure that the MUTE function is not activated.
(Refer to page 33.)
EXIT
57
Others
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection circuit
to operate so that the power
cannot be turned on.
( Insert the power cord plug into
the wall outlet and then press
the MAIN POWER switch.
NOTE:
B If the POWER button on the
projector does not illuminate red
when the MAIN POWER switch is
turned on, turn the MAIN POWER
switch off again and check that
the lamp unit and the lamp unit
cover are securely installed. Then
turn the MAIN POWER switch
back on.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the MAIN MENU
screen, and then press the F
and G buttons to move the
cursor to select “OPTION”.
Specifications
Power supply:
Power consumption:
Amps:
LCD panel:
Panel size (diagonal):
Aspect ratio:
Display method:
Drive method:
Pixels:
PT-L300U:
PT-L200U:
Lens:
Lamp:
Luminosity:
PT-L300U:
PT-L200U:
Scanning frequency:
Horizontal scanning frequency:
Vertical scanning frequency:
Dot clock frequency:
YPBPR signals:
Color system:
Projection size:
Throw distance:
Optical axis shift:
Screen aspect ratio:
Installation:
Speaker:
Max. useable volume output:
Connectors
VIDEO IN:
S2 VIDEO:
VIDEO:
PC IN:
RGB:
R.G.B.:
G.SYNC:
HD/SYNC:
VD:
58
100 V–240 V ~, 50 Hz/60 Hz
180 W (During standby (when fan is
stopped): Approx. 1.5 W)
2.2 A–0.8 A
0.7 type (17.78 mm)
16:9
3 transparent LCD panels (RGB)
Active matrix method
518 400 (960 x 540) x 3 panels
415 272 (858 x 484) x 3 panels
Manual zoom (1 - 1.2) / focus lens
F 2.0 - 2.3, f 22.0 mm - 26.2 mm
UHM lamp (120 W)
800 lm (ANSI)
700 lm (ANSI)
(for RGB signals):
30 kHz–70 kHz
50 Hz–87 Hz
Less than 100 MHz
525i (480i), 625i, 525p (480p), 750p
(720p), 1125i (1080i)
7 (NTSC/NTSC 4.43/PAL/PAL-M/PALN/PAL60/SECAM)
1016 mm - 5080 mm (40˝ - 200˝)
1.2 m - 7.4 m (3´11˝ - 24´3˝)
17:1 (fixed)
16:9
Front/Rear/Ceiling/Desk (Menu selection
method)
4 cm x 3 cm oval x 1
2 W (mono)
Single-line, Mini DIN 4-pin
Y 1.0 V [p-p], C 0.286 V [p-p], 75 Ω
Single-line, RCA pin jack
1.0 V [p-p], 75 Ω
Others
Problem
Possible cause
Remote control unit B The battery may be weak.
does not operate.
B The battery may not be inserted correctly. (Refer to
page 17.)
B The remote control signal receptor on the projector
may be obstructed. (Refer to page 17.)
B The remote control unit may be out of the
operation range. (Refer to page 17.)
The picture does not B The correct input signal may not be selected.
display correctly.
(Refer to page 22.)
B The signal format (TV system) may not be set
correctly. (Refer to page 35.)
B There may be a problem with the video tape or
other signal source.
B A signal which is not compatible with the projector
may be being input. (Refer to page 61.)
Picture from
B The cable may be too long.
computer does not B The external video output for the laptop computer
appear
may not be set correctly.
(You may be able to change the external output
settings by pressing the [Fn]+[F3] or [Fn]+[F10]
keys simultaneously. The actual method varies
depending on the type of computer, so refer to the
documentation provided with your computer for
further details.)
Single-line D-SUB HD 15-pin (female)
0.7 V [p-p], 75 Ω
1.0 V [p-p], 75 Ω
TTL high impedance, automatic
plus/minus polarity compatible
TTL high impedance, automatic
59
Specifications
Power supply:
Power consumption:
Amps:
LCD panel:
Panel size (diagonal):
Aspect ratio:
Display method:
Drive method:
Pixels:
PT-L300U:
PT-L200U:
Lens:
Lamp:
Luminosity:
PT-L300U:
PT-L200U:
Scanning frequency:
Horizontal scanning frequency:
Vertical scanning frequency:
Dot clock frequency:
YPBPR signals:
Color system:
Projection size:
Throw distance:
Optical axis shift:
Screen aspect ratio:
Installation:
Speaker:
Max. useable volume output:
Connectors
VIDEO IN:
S2 VIDEO:
VIDEO:
PC IN:
RGB:
R.G.B.:
G.SYNC:
HD/SYNC:
VD:
58
100 V–240 V ~, 50 Hz/60 Hz
180 W (During standby (when fan is
stopped): Approx. 1.5 W)
2.2 A–0.8 A
0.7 type (17.78 mm)
16:9
3 transparent LCD panels (RGB)
Active matrix method
518 400 (960 x 540) x 3 panels
415 272 (858 x 484) x 3 panels
Manual zoom (1 - 1.2) / focus lens
F 2.0 - 2.3, f 22.0 mm - 26.2 mm
UHM lamp (120 W)
800 lm (ANSI)
700 lm (ANSI)
(for RGB signals):
30 kHz–70 kHz
50 Hz–87 Hz
Less than 100 MHz
525i (480i), 625i, 525p (480p), 750p
(720p), 1125i (1080i)
7 (NTSC/NTSC 4.43/PAL/PAL-M/PALN/PAL60/SECAM)
1016 mm - 5080 mm (40˝ - 200˝)
1.2 m - 7.4 m (3´11˝ - 24´3˝)
17:1 (fixed)
16:9
Front/Rear/Ceiling/Desk (Menu selection
method)
4 cm x 3 cm oval x 1
2 W (mono)
Single-line, Mini DIN 4-pin
Y 1.0 V [p-p], C 0.286 V [p-p], 75 Ω
Single-line, RCA pin jack
1.0 V [p-p], 75 Ω
Others
Problem
Possible cause
Remote control unit B The battery may be weak.
does not operate.
B The battery may not be inserted correctly. (Refer to
page 17.)
B The remote control signal receptor on the projector
may be obstructed. (Refer to page 17.)
B The remote control unit may be out of the
operation range. (Refer to page 17.)
The picture does not B The correct input signal may not be selected.
display correctly.
(Refer to page 22.)
B The signal format (TV system) may not be set
correctly. (Refer to page 35.)
B There may be a problem with the video tape or
other signal source.
B A signal which is not compatible with the projector
may be being input. (Refer to page 61.)
Picture from
B The cable may be too long.
computer does not B The external video output for the laptop computer
appear
may not be set correctly.
(You may be able to change the external output
settings by pressing the [Fn]+[F3] or [Fn]+[F10]
keys simultaneously. The actual method varies
depending on the type of computer, so refer to the
documentation provided with your computer for
further details.)
Single-line D-SUB HD 15-pin (female)
0.7 V [p-p], 75 Ω
1.0 V [p-p], 75 Ω
TTL high impedance, automatic
plus/minus polarity compatible
TTL high impedance, automatic
59
SD memory card slot:
Cabinet:
Dimensions:
Width:
Height:
Length: PT-L300U
PT-L200U
Weight:
Operating environment:
Temperature:
Humidity:
Certifications:
<Remote control unit>
Power supply:
Operating range:
Weight:
Dimensions:
Width:
Height:
Length:
<Options>
Ceiling bracket
Projection Screen
1.0 V [p-p], 75 Ω
0.7 V [p-p], 75 Ω
Single-line, DVI-D, 24-pin
Single-line 0.5 V [rms], RCA pin jack x2
(L-R)
For SD memory cards
Compatible with DCF-standard still image
data
Compatible with MPEG4 moving picture
data (audio: G.726 compliant)
Moulded plastic (ABS/PC)
280 mm (11˝)
85.2 mm (3-11/32˝)
279.7 mm (11˝) (including lens)
278.5 mm (10-15/16˝) (including lens)
2.9 kg (6.4 lbs.)
0 °C–40 °C (32 °F–104 °F)
[When the FAN CONTROL is set to
“HIGH” (page 40); 0 °C–35 °C (32 °F–95
°F)]
20%–80% (no condensation)
UL60950, C-UL
FCC Class B
3 V DC (AAA battery x2)
Approx. 7 m (23´) (when operated directly
in front of signal receptor)
73.5 g (2.6 ozs.) (including battery)
43 mm (1-11/16˝)
22.3 mm (7/8˝)
135 mm (5-5/16˝)
ET-PKE300
ET-SR90CT(width: 1 800 mm(70˝))
ET-SR70CT(width: 1 400 mm(55˝))
*Specifications are subject to change without notice.
60
Appendix
List of compatible signals
Mode
Display
resolution
(dots)*1
NTSC/M-NTSC/PAL-M/PAL60 720 x 480i
PAL/PAL-N/SECAM
720 x 576i
525i
720 x 480i
625i
720 x 576i
525p
720 x 483
HDTV60
1 920 x 1 080i
HDTV50
1 920 x 1 080i
750P
1 280 x 720
VGA400
640 x 400
640 x 400
VGA480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
WIDE400
720 x 400
WIDE480
856 x 480
SVGA
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
MAC16
832 x 624
WIDE600
1 072 x 600
WIDE720
1 280 x 720
XGA
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768i
WIDE768
1 280 x 768
MXGA
1 152 x 864
1 152 x 864
MAC21
1 152 x 870
Scanning
frequency
H
V
(kHz) (Hz)
15.734
15.625
15.734
15.625
31.469
33.750
28.125
45.000
31.469
37.861
31.469
35.000
37.861
37.500
43.269
37.927
30.057
35.156
37.879
48.077
46.875
53.674
49.725
37.287
45.106
48.363
56.476
60.023
68.678
35.520
45.327
63.995
67.500
68.681
59.940
50.000
59.940
50.000
59.940
60.000
50.000
60.000
70.086
85.081
59.940
66.667
72.809
75.000
85.008
85.038
60.114
56.250
60.317
72.188
75.000
85.061
74.550
59.947
60.141
60.004
70.069
75.029
84.997
86.952
56.518
71.184
74.917
75.062
Picture
Dot clock
quality*2
frequency
(MHz) L300 L200
13.500
13.500
27.000
74.250
74.250
74.250
25.175
31.500
25.175
30.240
31.500
31.500
36.000
35.500
31.500
36.000
40.000
50.000
49.500
56.250
57.283
51.382
76.500
65.000
75.000
78.750
94.500
44.897
76.150
94.200
108.000
100.000
A
AA
A
AA
A
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
A
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
Format
Video/S-Video
Video/S-Video
YPBPR
YPBPR
YPBPR
YPBPR/PC
YPBPR/PC
YPBPR
PC
PC
PC/DV1
PC
PC
PC
PC
PC
PC/DV1
PC
PC/DV1
PC
PC
PC
PC
PC/DV1
PC
PC/DV1
PC
PC
PC
PC
PC/DV1
PC
PC
PC
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2 The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture
is projected
B Some loss of data occurs to make projection easier.
61
Others
plus/minus polarity compatible
COMPONENT IN:
Y:
PB,PR (CB,CR):
DVI-D IN (PT-L300U only):
AUDIO IN:
SD memory card slot:
Cabinet:
Dimensions:
Width:
Height:
Length: PT-L300U
PT-L200U
Weight:
Operating environment:
Temperature:
Humidity:
Certifications:
<Remote control unit>
Power supply:
Operating range:
Weight:
Dimensions:
Width:
Height:
Length:
<Options>
Ceiling bracket
Projection Screen
1.0 V [p-p], 75 Ω
0.7 V [p-p], 75 Ω
Single-line, DVI-D, 24-pin
Single-line 0.5 V [rms], RCA pin jack x2
(L-R)
For SD memory cards
Compatible with DCF-standard still image
data
Compatible with MPEG4 moving picture
data (audio: G.726 compliant)
Moulded plastic (ABS/PC)
280 mm (11˝)
85.2 mm (3-11/32˝)
279.7 mm (11˝) (including lens)
278.5 mm (10-15/16˝) (including lens)
2.9 kg (6.4 lbs.)
0 °C–40 °C (32 °F–104 °F)
[When the FAN CONTROL is set to
“HIGH” (page 40); 0 °C–35 °C (32 °F–95
°F)]
20%–80% (no condensation)
UL60950, C-UL
FCC Class B
3 V DC (AAA battery x2)
Approx. 7 m (23´) (when operated directly
in front of signal receptor)
73.5 g (2.6 ozs.) (including battery)
43 mm (1-11/16˝)
22.3 mm (7/8˝)
135 mm (5-5/16˝)
ET-PKE300
ET-SR90CT(width: 1 800 mm(70˝))
ET-SR70CT(width: 1 400 mm(55˝))
*Specifications are subject to change without notice.
60
Appendix
List of compatible signals
Mode
Display
resolution
(dots)*1
NTSC/M-NTSC/PAL-M/PAL60 720 x 480i
PAL/PAL-N/SECAM
720 x 576i
525i
720 x 480i
625i
720 x 576i
525p
720 x 483
HDTV60
1 920 x 1 080i
HDTV50
1 920 x 1 080i
750P
1 280 x 720
VGA400
640 x 400
640 x 400
VGA480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
WIDE400
720 x 400
WIDE480
856 x 480
SVGA
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
MAC16
832 x 624
WIDE600
1 072 x 600
WIDE720
1 280 x 720
XGA
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768i
WIDE768
1 280 x 768
MXGA
1 152 x 864
1 152 x 864
MAC21
1 152 x 870
Scanning
frequency
H
V
(kHz) (Hz)
15.734
15.625
15.734
15.625
31.469
33.750
28.125
45.000
31.469
37.861
31.469
35.000
37.861
37.500
43.269
37.927
30.057
35.156
37.879
48.077
46.875
53.674
49.725
37.287
45.106
48.363
56.476
60.023
68.678
35.520
45.327
63.995
67.500
68.681
59.940
50.000
59.940
50.000
59.940
60.000
50.000
60.000
70.086
85.081
59.940
66.667
72.809
75.000
85.008
85.038
60.114
56.250
60.317
72.188
75.000
85.061
74.550
59.947
60.141
60.004
70.069
75.029
84.997
86.952
56.518
71.184
74.917
75.062
Picture
Dot clock
quality*2
frequency
(MHz) L300 L200
13.500
13.500
27.000
74.250
74.250
74.250
25.175
31.500
25.175
30.240
31.500
31.500
36.000
35.500
31.500
36.000
40.000
50.000
49.500
56.250
57.283
51.382
76.500
65.000
75.000
78.750
94.500
44.897
76.150
94.200
108.000
100.000
A
AA
A
AA
A
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
A
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
Format
Video/S-Video
Video/S-Video
YPBPR
YPBPR
YPBPR
YPBPR/PC
YPBPR/PC
YPBPR
PC
PC
PC/DV1
PC
PC
PC
PC
PC
PC/DV1
PC
PC/DV1
PC
PC
PC
PC
PC/DV1
PC
PC/DV1
PC
PC
PC
PC
PC/DV1
PC
PC
PC
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2 The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture
is projected
B Some loss of data occurs to make projection easier.
61
Others
plus/minus polarity compatible
COMPONENT IN:
Y:
PB,PR (CB,CR):
DVI-D IN (PT-L300U only):
AUDIO IN:
Connector pin wiring
B The pin layout and signal names for the S2 VIDEO input connector are
shown below.
B The pin assignments on the DVI-D input connector are as follows
(interface with TMDS connector on a personal computer)
:
#
$
&
%
Pin No.
#
$
%
&
Signal
Earth (Luminance signal)
Earth (Color signal)
Luminance signal
Color signal
External view
B The pin layout and signal names for the RGB input connector are shown
below.
-
1
(
,
#
'
External view
Pin No.
#
$
%
.
/
0
1
Signal
R
G/G·SYNC
B
SDA
HD/SYNC
VD
SCL
Pin + is spare.
Pins &–*, , and - are for earth.
Pins . and 1 functions are only valid when
supported by the computer
3
+
2
*
#
View from mating side
Pin No.
#
$
%
&
'
(
)
*
+
,
.
Signal
T.M.D.S data 2T T.M.D.S data 2+
T.M.D.S data 2/4 shield
T.M.D.S data 4T.M.D.S data 4+
DDC clock
DDC data
T.M.D.S data 1T.M.D.S data 1+
T.M.D.S data1/3 shield
T.M.D.S data 3-
Pin No.
/
0
1
2
3
4
5
6
7
8
9
:
Signal
T.M.D.S data 3+
+5 V
Ground
Hot plug sense
T.M.D.S data 0T.M.D.S data 0+
T.M.D.S data 0/5 shield
T.M.D.S data 5T.M.D.S data 5+
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock-
Projection dimensions calculation methods
The following methods will allow you to calculate dimensions such as screen
diagonal length and projection distances. Units in all calculations are metre.
SD
LW/LT
Screen Width: SW=SDx0.872
Screen Height: SH=SDx0.490
Minimum Projection Distance: LW=1.229xSD-0.0381
Maximum Projection Distance: LT=1.481xSD-0.0381
Image Lower Edge from Lens Center: H1=SW/32
62
Others
H1
SH
16:9
SW
63
Connector pin wiring
B The pin layout and signal names for the S2 VIDEO input connector are
shown below.
B The pin assignments on the DVI-D input connector are as follows
(interface with TMDS connector on a personal computer)
:
#
$
&
%
Pin No.
#
$
%
&
Signal
Earth (Luminance signal)
Earth (Color signal)
Luminance signal
Color signal
External view
B The pin layout and signal names for the RGB input connector are shown
below.
-
1
(
,
#
'
External view
Pin No.
#
$
%
.
/
0
1
Signal
R
G/G·SYNC
B
SDA
HD/SYNC
VD
SCL
Pin + is spare.
Pins &–*, , and - are for earth.
Pins . and 1 functions are only valid when
supported by the computer
3
+
2
*
#
View from mating side
Pin No.
#
$
%
&
'
(
)
*
+
,
.
Signal
T.M.D.S data 2T T.M.D.S data 2+
T.M.D.S data 2/4 shield
T.M.D.S data 4T.M.D.S data 4+
DDC clock
DDC data
T.M.D.S data 1T.M.D.S data 1+
T.M.D.S data1/3 shield
T.M.D.S data 3-
Pin No.
/
0
1
2
3
4
5
6
7
8
9
:
Signal
T.M.D.S data 3+
+5 V
Ground
Hot plug sense
T.M.D.S data 0T.M.D.S data 0+
T.M.D.S data 0/5 shield
T.M.D.S data 5T.M.D.S data 5+
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock-
Projection dimensions calculation methods
The following methods will allow you to calculate dimensions such as screen
diagonal length and projection distances. Units in all calculations are metre.
SD
LW/LT
Screen Width: SW=SDx0.872
Screen Height: SH=SDx0.490
Minimum Projection Distance: LW=1.229xSD-0.0381
Maximum Projection Distance: LT=1.481xSD-0.0381
Image Lower Edge from Lens Center: H1=SW/32
62
Others
H1
SH
16:9
SW
63
DCF standard
Dimensions
269(10-9/16)
85.2(3-11/32)
80.2(3-5/32)
Folders must be created as sub-folders of the DCIM folder on the SD
memory card.
B Data which is contained within any folder other than the DCIM folder
cannot be recognised.
Folder names must consist of three numerals (folder number) followed
by five alphanumeric characters. (Example: 100abcde)
B The three numerals must make up a number between 100 and 999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)
Multiple folders using the same three-digit combination (folder number)
cannot be created.
B For example, if two folders exist named "100abcde" and "100fghij"
respectively, the projector will not recognise them.
Folder sub-hierarchies are not supported.
B For example, if a folder called "323fghij" is created as a sub-folder of the
"102abcde" folder, the projector will not be able to recognise the subfolder.
49.7(1 15/16)
Limits on folder names
<Units: mm (˝)>
PT-L300U: 279.7(11)
PT-L200U: 278.5(10 15/16)
This projector can only play back image files which comply with the DCF
specification. The DCF specification imposes the following conditions. Image
files or folders which do not conform to these conditions cannot be
recognised by the projector.
65.4(2 9/16)
280(11)
File names
File format
B Only JPEG image files which comply with the Exif 2.2 standard are
recognised.
64
Trademark acknowledgements
B The SD logo is a trademark.
B VGA and XGA are trademarks of International Business Machines
Corporation.
B Macintosh is a registered trademark of Apple Computer, Inc.
B S-VGA is a registered trademark of the Video Electronics Standards
Association.
All other trademarks are the property of the various trademark owners.
Others
File names must consist of four alphanumeric characters followed by
four numerals (file number), followed by ".jpg". (Example: abcd0001.jpg)
B The four numerals must make up a number between 0001 and 9999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)
Multiple file names using the same four-digit combination (file number)
cannot be created.
B For example, if two files exist named "abcd0001.jpg" and "efgh0001.jpg"
respectively, the projector cannot recognise them normally.
65
DCF standard
Dimensions
269(10-9/16)
85.2(3-11/32)
80.2(3-5/32)
Folders must be created as sub-folders of the DCIM folder on the SD
memory card.
B Data which is contained within any folder other than the DCIM folder
cannot be recognised.
Folder names must consist of three numerals (folder number) followed
by five alphanumeric characters. (Example: 100abcde)
B The three numerals must make up a number between 100 and 999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)
Multiple folders using the same three-digit combination (folder number)
cannot be created.
B For example, if two folders exist named "100abcde" and "100fghij"
respectively, the projector will not recognise them.
Folder sub-hierarchies are not supported.
B For example, if a folder called "323fghij" is created as a sub-folder of the
"102abcde" folder, the projector will not be able to recognise the subfolder.
49.7(1 15/16)
Limits on folder names
<Units: mm (˝)>
PT-L300U: 279.7(11)
PT-L200U: 278.5(10 15/16)
This projector can only play back image files which comply with the DCF
specification. The DCF specification imposes the following conditions. Image
files or folders which do not conform to these conditions cannot be
recognised by the projector.
65.4(2 9/16)
280(11)
File names
File format
B Only JPEG image files which comply with the Exif 2.2 standard are
recognised.
64
Trademark acknowledgements
B The SD logo is a trademark.
B VGA and XGA are trademarks of International Business Machines
Corporation.
B Macintosh is a registered trademark of Apple Computer, Inc.
B S-VGA is a registered trademark of the Video Electronics Standards
Association.
All other trademarks are the property of the various trademark owners.
Others
File names must consist of four alphanumeric characters followed by
four numerals (file number), followed by ".jpg". (Example: abcd0001.jpg)
B The four numerals must make up a number between 0001 and 9999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)
Multiple file names using the same four-digit combination (file number)
cannot be created.
B For example, if two files exist named "abcd0001.jpg" and "efgh0001.jpg"
respectively, the projector cannot recognise them normally.
65
AVERTISSEMENT: POUR REDUIRE LES RISQUES DE FEU OU DE CHOC
ÉLECTRIQUE, NE PAS EXPOSER CE PRODUIT À L’EAU
OU À L’HUMIDITÉ
Alimentation: Ce projecteur LCD est conçu pour fonctionner sur secteur
de 100 V - 240 V, 50 Hz/60 Hz seulement.
ATTENTION: Le cordon d’alimentation secteur fourni avec le projecteur
peut être utilisé uniquement pour une alimentation électrique
de 125 V, 7 A maximum. Si on veut l’utiliser avec une
tension ou un courant plus forts, on doit se procurer un autre
cordon d’alimentation de 250 V. Si on utilise le cordon fourni
sous ces conditions, risque de provoquer un incendie.
Le symbole de la flèche en forme d’éclair, dans un triangle,
avertit l’usager de la présence de “tensions dangereuses” à
l’intérieur du produit qui peuvent être de force suffisante pour
constituer un risque de choc électrique aux personnes.
Le point d’exclamation dans un triangle avertit l’usager de la
présence d’instructions importantes concernant l’utilisation et
l’entretien (réparation) dans la littérature accompagnant le
produit.
ATTENTION: Cet appareil est équipé d’une fiche
de courant à trois broches avec
mise à la terre. Ne pas retirer la
broche de mise à la masse de la
Ne pas retirer
fiche.
Cette fiche ne pourra être utilisée que dans une prise avec
mise à la terre. Ceci est une précaution sécuritaire. S’il est
impossible d’insérer la fiche dans la prise, s’adresser à un
électricien. Ne pas annuler la protection de la fiche à mise à
la terre.
66
Précautions concernant la sécurité
AVERTISSEMENT
En cas de problème (pas d’image ou de son), ou si le projecteur dégage
de la fumée ou une odeur étrange, éteindre l’appareil et débrancher
immédiatement la fiche d’alimentation de la prise de courant.
B Ne pas continuer d’utiliser le projecteur dans ces cas, autrement cela peut
entraîner un incendie ou des chocs électriques.
B Après s’être assuré que de la fumée ne se dégage plus, s’adresser à un
centre technique agréé et demander que les réparations nécessaires
soient faites.
B Le fait de réparer le projecteur soi-même est très dangereux, et ne doit
jamais être fait.
Ne pas regarder directement dans la lentille pendant que le projecteur
fonctionne.
B Une lumière intense est émise par la lentille du projecteur. Si l’on regarde
directement dans cette lumière, elle risque de causer des blessures et de
graves lésions aux yeux.
B Veiller particulixerement à ce que les enfants ne regardent pas dans
l’objectif.
En outre, éteindre le projecteur si on le laisse sans surveillance.
Ne pas installer ce projecteur dans un endroit qui n’est pas assez
résistant pour supporter le poids du projecteur.
B Si l’emplacement d’installation n’est pas assez résistant, le projecteur
risque de tomber et causer de graves blessures et (ou) des dommages.
Demander à un technicien qualifié d’installer le projecteur par exemple
s’il est installé au plafond.
B Si l’installation n’est pas faite correctement, cela peut entraîner des
blessures ou des chocs électriques.
Si de l’eau ou des objets étrangers entrent dans le projecteur, si le
projecteur tombe, ou si le boîtier est endommagé, éteindre l’appareil et
débrancher immédiatement la fiche d’alimentation de la prise de
courant.
B Si l’on continue d’utiliser le projecteur dans cette condition, cela peut
entraîner un incendie ou des chocs électriques.
B S’adresser à un centre technique agréé pour que les réparations
nécessaires puissent être faites.
Ne pas surcharger la prise de courant.
B Si l’alimentation est surchargée (par exemple, par l’utilisation de trop
d’adaptateurs), cela risque de faire surchauffer le projecteur et peut
entraîner un incendie.
Ne pas retirer le capot ou le modifier.
B Des hautes tensions qui peuvent causer de graves blessures sont
67
Others
NOTES IMPORTANTES
CONCERNANT LA SÉCURITÉ
AVERTISSEMENT: POUR REDUIRE LES RISQUES DE FEU OU DE CHOC
ÉLECTRIQUE, NE PAS EXPOSER CE PRODUIT À L’EAU
OU À L’HUMIDITÉ
Alimentation: Ce projecteur LCD est conçu pour fonctionner sur secteur
de 100 V - 240 V, 50 Hz/60 Hz seulement.
ATTENTION: Le cordon d’alimentation secteur fourni avec le projecteur
peut être utilisé uniquement pour une alimentation électrique
de 125 V, 7 A maximum. Si on veut l’utiliser avec une
tension ou un courant plus forts, on doit se procurer un autre
cordon d’alimentation de 250 V. Si on utilise le cordon fourni
sous ces conditions, risque de provoquer un incendie.
Le symbole de la flèche en forme d’éclair, dans un triangle,
avertit l’usager de la présence de “tensions dangereuses” à
l’intérieur du produit qui peuvent être de force suffisante pour
constituer un risque de choc électrique aux personnes.
Le point d’exclamation dans un triangle avertit l’usager de la
présence d’instructions importantes concernant l’utilisation et
l’entretien (réparation) dans la littérature accompagnant le
produit.
ATTENTION: Cet appareil est équipé d’une fiche
de courant à trois broches avec
mise à la terre. Ne pas retirer la
broche de mise à la masse de la
Ne pas retirer
fiche.
Cette fiche ne pourra être utilisée que dans une prise avec
mise à la terre. Ceci est une précaution sécuritaire. S’il est
impossible d’insérer la fiche dans la prise, s’adresser à un
électricien. Ne pas annuler la protection de la fiche à mise à
la terre.
66
Précautions concernant la sécurité
AVERTISSEMENT
En cas de problème (pas d’image ou de son), ou si le projecteur dégage
de la fumée ou une odeur étrange, éteindre l’appareil et débrancher
immédiatement la fiche d’alimentation de la prise de courant.
B Ne pas continuer d’utiliser le projecteur dans ces cas, autrement cela peut
entraîner un incendie ou des chocs électriques.
B Après s’être assuré que de la fumée ne se dégage plus, s’adresser à un
centre technique agréé et demander que les réparations nécessaires
soient faites.
B Le fait de réparer le projecteur soi-même est très dangereux, et ne doit
jamais être fait.
Ne pas regarder directement dans la lentille pendant que le projecteur
fonctionne.
B Une lumière intense est émise par la lentille du projecteur. Si l’on regarde
directement dans cette lumière, elle risque de causer des blessures et de
graves lésions aux yeux.
B Veiller particulixerement à ce que les enfants ne regardent pas dans
l’objectif.
En outre, éteindre le projecteur si on le laisse sans surveillance.
Ne pas installer ce projecteur dans un endroit qui n’est pas assez
résistant pour supporter le poids du projecteur.
B Si l’emplacement d’installation n’est pas assez résistant, le projecteur
risque de tomber et causer de graves blessures et (ou) des dommages.
Demander à un technicien qualifié d’installer le projecteur par exemple
s’il est installé au plafond.
B Si l’installation n’est pas faite correctement, cela peut entraîner des
blessures ou des chocs électriques.
Si de l’eau ou des objets étrangers entrent dans le projecteur, si le
projecteur tombe, ou si le boîtier est endommagé, éteindre l’appareil et
débrancher immédiatement la fiche d’alimentation de la prise de
courant.
B Si l’on continue d’utiliser le projecteur dans cette condition, cela peut
entraîner un incendie ou des chocs électriques.
B S’adresser à un centre technique agréé pour que les réparations
nécessaires puissent être faites.
Ne pas surcharger la prise de courant.
B Si l’alimentation est surchargée (par exemple, par l’utilisation de trop
d’adaptateurs), cela risque de faire surchauffer le projecteur et peut
entraîner un incendie.
Ne pas retirer le capot ou le modifier.
B Des hautes tensions qui peuvent causer de graves blessures sont
67
Others
NOTES IMPORTANTES
CONCERNANT LA SÉCURITÉ
68
incendie ou des chocs électriques.
Ne pas laisser les bornes + et - de la pile entrer en contact avec des
objets métalliques tels que des colliers ou des épingles à cheveux.
B Cela peut faire que la pile fuit, surchauffe, éclate ou prenne feu.
B Garder la pile dans un sachet en plastique et la maintenir éloignée des
objets métalliques.
Pendant un orage, ne pas toucher le projecteur ou le câble.
B Il y a risque d’électrocution.
Ne pas utiliser l’appareil dans un bain ou une douche.
BIl y a risque d’incendie ou d’électrocution.
Ne pas placer ses mains ou autres objets près de la sortie d’air.
B De l’air chaud sort par l’ouverture de sortie d’air. Ne pas placer les mains
ou la figure, ou d’autres objets qui ne peuvent résister à la chaleur près de
cette sortie d’air, sinon cela peut causer des blessures ou des dommages.
Le remplacement de l’unité de lampe ne devrait être effectué que par un
technicien qualifié.
B L’unité de lampe a une pression interne élevée. Elle peut facilement
s’endommager si cognée contre des objets durs ou si elle tombe, cela
peut causer des blessures ou des mauvais fonctionnements.
Lors du remplacement de la lampe, la laisser refroidir pendant au
moins une heure avant de la manipuler.
B Le couvercle de la lampe devient très chaud, et on risque de se brûler si
on le touche.
Avant de remplacer la lampe, veiller à débrancher le cordon
d’alimentation de la prise de courant.
B Il y a risque d’électrocution ou d’explosion.
Attention
Ne pas obstruer les orifices d’entrée et de sortie d’air.
B Cela risque de faire surchauffer le projecteur, et causer un incendie ou
endommager le projecteur.
Ne pas installer le projecteur dans des endroits humides ou
poussiéreux ou dans des endroits où le projecteur peut entrer en
contact avec de la fumée ou la vapeur.
B L’utilisation du projecteur dans de telles conditions peut causer un
incendie ou des chocs électriques.
Pour débrancher le cordon d’alimentation, tenir la fiche et non pas le
cordon.
B Si le cordon d’alimentation est tiré, le cordon sera endommagé et cela
peut causer un incendie, des courts-circuits ou des chocs électriques
sérieux.
Others
présentes à l’intérieur du projecteur.
B Pour toute inspection, réglage ou réparation, s’adresser à un centre
technique agréé.
Nettoyer la fiche du cordon d’alimentation régulièrement afin d’éviter
toute accumulation de poussière.
B Si de la poussière s’accumule sur la fiche du cordon d’alimentation,
l’humidité peut endommager l’isolant et entraîner un incendie. Débrancher
le cordon d’alimentation de la prise de courant et l’essuyer avec un chiffon
sec.
B Si le projecteur n’est pas utilisé pendant une période prolongée,
débrancher le cordon d’alimentation de la prise de courant.
Faire attention de ne pas endommager le cordon d’alimentation.
B Ne pas endommager le cordon d’alimentation, ne pas le modifier, ne pas
placer sous des objets lourds, ne pas le chauffer, ne pas le placer près
d’objets chauffants, ne pas le tordre, ne pas le plier ou le tirer
excessivement et ne pas le rouler en boule.
B Si le cordon d’alimentation est endommagé, cela peut entraîner un
incendie et des chocs électriques.
B Si le cordon d’alimentation est endommagé, le faire réparer par un centre
technique agréé.
Ne pas manipuler le cordon d’alimentation avec les mains mouillées.
B Cela peut entraîner des chocs électriques.
Brancher la fiche du cordon d’alimentation fermement dans la prise de
courant.
B Si la fiche n’est pas complètement insérée, cela peut entraîner des chocs
électriques ou la faire surchauffer.
B Si la fiche est endommagée ou la plaque de la prise est desserrée, elles
ne devraient pas être utilisées.
Ne pas placer le projecteur sur des surfaces instables.
B Si le projecteur est placé sur une surface qui est inclinée ou instable, il
risque de tomber ou de se renverser et cela peut causer des blessures ou
des dommages.
Ne pas placer le projecteur dans l’eau ou ne pas le laisser se mouiller.
B Sinon cela peut causer un incendie ou des chocs électriques.
Ne pas placer des récipients de liquide sur le projecteur.
B Si de l’eau se renverse sur le projecteur, s’adresser à un centre technique
agréé.
B Si de l’eau entre à l’intérieur du projecteur, entrer en contact avec un
centre technique agréé.
Ne pas mettre d’objets étrangers dans le projecteur.
B Ne pas insérer d’objets métalliques ou inflammables dans les orifices de
ventilation ou les faire tomber sur le projecteur, car cela peut causer un
69
68
incendie ou des chocs électriques.
Ne pas laisser les bornes + et - de la pile entrer en contact avec des
objets métalliques tels que des colliers ou des épingles à cheveux.
B Cela peut faire que la pile fuit, surchauffe, éclate ou prenne feu.
B Garder la pile dans un sachet en plastique et la maintenir éloignée des
objets métalliques.
Pendant un orage, ne pas toucher le projecteur ou le câble.
B Il y a risque d’électrocution.
Ne pas utiliser l’appareil dans un bain ou une douche.
BIl y a risque d’incendie ou d’électrocution.
Ne pas placer ses mains ou autres objets près de la sortie d’air.
B De l’air chaud sort par l’ouverture de sortie d’air. Ne pas placer les mains
ou la figure, ou d’autres objets qui ne peuvent résister à la chaleur près de
cette sortie d’air, sinon cela peut causer des blessures ou des dommages.
Le remplacement de l’unité de lampe ne devrait être effectué que par un
technicien qualifié.
B L’unité de lampe a une pression interne élevée. Elle peut facilement
s’endommager si cognée contre des objets durs ou si elle tombe, cela
peut causer des blessures ou des mauvais fonctionnements.
Lors du remplacement de la lampe, la laisser refroidir pendant au
moins une heure avant de la manipuler.
B Le couvercle de la lampe devient très chaud, et on risque de se brûler si
on le touche.
Avant de remplacer la lampe, veiller à débrancher le cordon
d’alimentation de la prise de courant.
B Il y a risque d’électrocution ou d’explosion.
Attention
Ne pas obstruer les orifices d’entrée et de sortie d’air.
B Cela risque de faire surchauffer le projecteur, et causer un incendie ou
endommager le projecteur.
Ne pas installer le projecteur dans des endroits humides ou
poussiéreux ou dans des endroits où le projecteur peut entrer en
contact avec de la fumée ou la vapeur.
B L’utilisation du projecteur dans de telles conditions peut causer un
incendie ou des chocs électriques.
Pour débrancher le cordon d’alimentation, tenir la fiche et non pas le
cordon.
B Si le cordon d’alimentation est tiré, le cordon sera endommagé et cela
peut causer un incendie, des courts-circuits ou des chocs électriques
sérieux.
Others
présentes à l’intérieur du projecteur.
B Pour toute inspection, réglage ou réparation, s’adresser à un centre
technique agréé.
Nettoyer la fiche du cordon d’alimentation régulièrement afin d’éviter
toute accumulation de poussière.
B Si de la poussière s’accumule sur la fiche du cordon d’alimentation,
l’humidité peut endommager l’isolant et entraîner un incendie. Débrancher
le cordon d’alimentation de la prise de courant et l’essuyer avec un chiffon
sec.
B Si le projecteur n’est pas utilisé pendant une période prolongée,
débrancher le cordon d’alimentation de la prise de courant.
Faire attention de ne pas endommager le cordon d’alimentation.
B Ne pas endommager le cordon d’alimentation, ne pas le modifier, ne pas
placer sous des objets lourds, ne pas le chauffer, ne pas le placer près
d’objets chauffants, ne pas le tordre, ne pas le plier ou le tirer
excessivement et ne pas le rouler en boule.
B Si le cordon d’alimentation est endommagé, cela peut entraîner un
incendie et des chocs électriques.
B Si le cordon d’alimentation est endommagé, le faire réparer par un centre
technique agréé.
Ne pas manipuler le cordon d’alimentation avec les mains mouillées.
B Cela peut entraîner des chocs électriques.
Brancher la fiche du cordon d’alimentation fermement dans la prise de
courant.
B Si la fiche n’est pas complètement insérée, cela peut entraîner des chocs
électriques ou la faire surchauffer.
B Si la fiche est endommagée ou la plaque de la prise est desserrée, elles
ne devraient pas être utilisées.
Ne pas placer le projecteur sur des surfaces instables.
B Si le projecteur est placé sur une surface qui est inclinée ou instable, il
risque de tomber ou de se renverser et cela peut causer des blessures ou
des dommages.
Ne pas placer le projecteur dans l’eau ou ne pas le laisser se mouiller.
B Sinon cela peut causer un incendie ou des chocs électriques.
Ne pas placer des récipients de liquide sur le projecteur.
B Si de l’eau se renverse sur le projecteur, s’adresser à un centre technique
agréé.
B Si de l’eau entre à l’intérieur du projecteur, entrer en contact avec un
centre technique agréé.
Ne pas mettre d’objets étrangers dans le projecteur.
B Ne pas insérer d’objets métalliques ou inflammables dans les orifices de
ventilation ou les faire tomber sur le projecteur, car cela peut causer un
69
70
Précautions concernant la manipulation
Précautions à prendre lors du déplacement du
projecteur
Veiller à bien mettre le capuchon d’objectif en place avant de déplacer le
projecteur.
L’objectif de projection est très sensible aux vibrations et aux chocs. Lorsqu’on
déplace le projecteur, utiliser la sacoche de transport fournie. Lorsqu’on place le
projecteur dans la sacoche de transport, le placer de façon que l’objectif soit
orienté vers le haut.
Avertissements concernant l’installation
Toujours observer les points suivants lors de l’installation du projecteur.
Éviter de l’installer dans les endroits sujets à des vibrations ou à des chocs.
Si le projecteur est installé dans les endroits sujets à de fortes vibrations, comme
près d’un moteur, ou s’il est installé à l’intérieur d’un véhicule ou à bord d’un
bateau, le projecteur peut être soumis à une vibration ou à des chocs qui peuvent
endommager les pièces internes et causer des mauvais fonctionnements ou des
accidents. Dès lors, installer le projecteur dans un endroit qui n’est pas soumis à
des vibrations ou des chocs.
Ne pas installer le projecteur près de lignes d’alimentation électrique à
haute tension ou de moteurs.
Le projecteur peut être sujet à une interférence électromagnétique s’il est installé
près de lignes d’alimentation électrique à haute tension ou de moteurs.
Si le projecteur est installé au plafond, demander à un technicien qualifié de
faire tous les travaux d’installation.
Si le projecteur doit être suspendu au plafond, il faut acheter le kit d’installation
séparé (numéro de modèle: ET-PKE300). De plus, tous les travaux d’installation
ne devraient être faits que par un technicien qualifié.
Si l’on utilise ce projecteur à un endroit élevé (au-dessus de 1400 m),
régler le VENTILATEUR à HAUTE. (Se référer à la page 40.)
Sinon, des anomalies pourront se produire.
Notes sur l’utilisation
Afin d’obtenir la meilleure qualité d’image
Si la lumière extérieure ou la lumière des lampes intérieures brille sur l’écran, les
images projetées n’auront pas un bon contraste. Tirer les rideaux ou les stores de
toutes les fenêtres et éteindre toutes les lumières fluorescentes près de l’écran
pour empêcher la réflexion.
Ne pas toucher aux surfaces de la lentille avec les mains nues.
Si la surface de la lentille est salie par des empreintes digitales ou autre, ceci sera
agrandi et projeté sur l’écran. D’ailleurs, lorsque le projecteur n’est pas utilisé,
rétracter la lentille, puis la couvrir à l’aide du capuchon d’objectif fourni.
Others
Débrancher toujours tous les câbles avant de déplacer le projecteur.
B Le fait de déplacer le projecteur avec des câbles branchés peut
endommager les câbles, ce qui pourraient causer un incendie ou des
chocs électriques.
Ne pas placer d’objets lourds sur le projecteur.
B Cela peut déséquilibrer le projecteur et le faire tomber, ce qui peut
entraîner des dommages ou des blessures.
Ne pas court-circuiter, chauffer ou démonter la pile et ne pas la placer
dans l’eau ou le feu.
B Cela peut faire que la pile fuit, surchauffe, éclate ou prenne feu et causer
des brûlures ou autres blessures.
Lors de l’insertion de la pile, s’assurer que les polarités (+ et -) sont
correctes.
B Si la pile est insérée incorrectement, elle peut éclater ou fuir et cela peut
causer un incendie, des blessures ou la contamination du compartiment
des piles.
N’utiliser que la pile indiquée.
B Si une pile incorrecte est utilisée, elle peut éclater ou fuire et cela peut
causer un incendie, des blessures ou la contamination du compartiment
des piles.
Ne pas mélanger des piles usées et des piles neuves.
B Si l’on insère les piles incorrectement, elles risqueront d’exploser ou de
fuir, ce qui peut causer un incendie, des blessures ou une contamination
du logement des piles et de la zone environnante.
Ne pas peser de tout son poids sur ce projecteur.
B On risque de tomber ou de casser l’appareil, ce qui peut causer des
blessures.
B Veiller tout particulièrement à ce que des enfants ne montent pas sur
l’appareil.
Débrancher la fiche du cordon d’alimentation de la prise de courant
comme mesure de sécurité avant d’effectuer tout nettoyage.
B Sinon cela peut causer des chocs électriques.
Demander à un centre technique agréé de nettoyer l’intérieur du
projecteur au moins une fois par an.
B S’il n’est pas nettoyé et que la poussière s’accumule à l’intérieur du
projecteur, cela peut causer un incendie ou des problèmes de
fonctionnement.
B Il est recommandé de nettoyer l’intérieur du projecteur avant que la saison
humide n’arrive. Demander au centre technique agréé plus proche de
nettoyer le projecteur lorsque cela est requis. Se renseigner auprès du
centre technique agréé pour le coût du nettoyage.
Nous faisons tous les efforts possibles afin de préserver
l’environnement. Prière d’apporter l’appareil, s’il n’est pas réparable, à
votre revendeur ou à un centre de recyclage.
71
70
Précautions concernant la manipulation
Précautions à prendre lors du déplacement du
projecteur
Veiller à bien mettre le capuchon d’objectif en place avant de déplacer le
projecteur.
L’objectif de projection est très sensible aux vibrations et aux chocs. Lorsqu’on
déplace le projecteur, utiliser la sacoche de transport fournie. Lorsqu’on place le
projecteur dans la sacoche de transport, le placer de façon que l’objectif soit
orienté vers le haut.
Avertissements concernant l’installation
Toujours observer les points suivants lors de l’installation du projecteur.
Éviter de l’installer dans les endroits sujets à des vibrations ou à des chocs.
Si le projecteur est installé dans les endroits sujets à de fortes vibrations, comme
près d’un moteur, ou s’il est installé à l’intérieur d’un véhicule ou à bord d’un
bateau, le projecteur peut être soumis à une vibration ou à des chocs qui peuvent
endommager les pièces internes et causer des mauvais fonctionnements ou des
accidents. Dès lors, installer le projecteur dans un endroit qui n’est pas soumis à
des vibrations ou des chocs.
Ne pas installer le projecteur près de lignes d’alimentation électrique à
haute tension ou de moteurs.
Le projecteur peut être sujet à une interférence électromagnétique s’il est installé
près de lignes d’alimentation électrique à haute tension ou de moteurs.
Si le projecteur est installé au plafond, demander à un technicien qualifié de
faire tous les travaux d’installation.
Si le projecteur doit être suspendu au plafond, il faut acheter le kit d’installation
séparé (numéro de modèle: ET-PKE300). De plus, tous les travaux d’installation
ne devraient être faits que par un technicien qualifié.
Si l’on utilise ce projecteur à un endroit élevé (au-dessus de 1400 m),
régler le VENTILATEUR à HAUTE. (Se référer à la page 40.)
Sinon, des anomalies pourront se produire.
Notes sur l’utilisation
Afin d’obtenir la meilleure qualité d’image
Si la lumière extérieure ou la lumière des lampes intérieures brille sur l’écran, les
images projetées n’auront pas un bon contraste. Tirer les rideaux ou les stores de
toutes les fenêtres et éteindre toutes les lumières fluorescentes près de l’écran
pour empêcher la réflexion.
Ne pas toucher aux surfaces de la lentille avec les mains nues.
Si la surface de la lentille est salie par des empreintes digitales ou autre, ceci sera
agrandi et projeté sur l’écran. D’ailleurs, lorsque le projecteur n’est pas utilisé,
rétracter la lentille, puis la couvrir à l’aide du capuchon d’objectif fourni.
Others
Débrancher toujours tous les câbles avant de déplacer le projecteur.
B Le fait de déplacer le projecteur avec des câbles branchés peut
endommager les câbles, ce qui pourraient causer un incendie ou des
chocs électriques.
Ne pas placer d’objets lourds sur le projecteur.
B Cela peut déséquilibrer le projecteur et le faire tomber, ce qui peut
entraîner des dommages ou des blessures.
Ne pas court-circuiter, chauffer ou démonter la pile et ne pas la placer
dans l’eau ou le feu.
B Cela peut faire que la pile fuit, surchauffe, éclate ou prenne feu et causer
des brûlures ou autres blessures.
Lors de l’insertion de la pile, s’assurer que les polarités (+ et -) sont
correctes.
B Si la pile est insérée incorrectement, elle peut éclater ou fuir et cela peut
causer un incendie, des blessures ou la contamination du compartiment
des piles.
N’utiliser que la pile indiquée.
B Si une pile incorrecte est utilisée, elle peut éclater ou fuire et cela peut
causer un incendie, des blessures ou la contamination du compartiment
des piles.
Ne pas mélanger des piles usées et des piles neuves.
B Si l’on insère les piles incorrectement, elles risqueront d’exploser ou de
fuir, ce qui peut causer un incendie, des blessures ou une contamination
du logement des piles et de la zone environnante.
Ne pas peser de tout son poids sur ce projecteur.
B On risque de tomber ou de casser l’appareil, ce qui peut causer des
blessures.
B Veiller tout particulièrement à ce que des enfants ne montent pas sur
l’appareil.
Débrancher la fiche du cordon d’alimentation de la prise de courant
comme mesure de sécurité avant d’effectuer tout nettoyage.
B Sinon cela peut causer des chocs électriques.
Demander à un centre technique agréé de nettoyer l’intérieur du
projecteur au moins une fois par an.
B S’il n’est pas nettoyé et que la poussière s’accumule à l’intérieur du
projecteur, cela peut causer un incendie ou des problèmes de
fonctionnement.
B Il est recommandé de nettoyer l’intérieur du projecteur avant que la saison
humide n’arrive. Demander au centre technique agréé plus proche de
nettoyer le projecteur lorsque cela est requis. Se renseigner auprès du
centre technique agréé pour le coût du nettoyage.
Nous faisons tous les efforts possibles afin de préserver
l’environnement. Prière d’apporter l’appareil, s’il n’est pas réparable, à
votre revendeur ou à un centre de recyclage.
71
Avant de faire le nettoyage et l’entretien, s’assurer de
débrancher la fiche du cordon d’alimentation de la
prise de courant.
Essuyer le boîtier avec un tissu doux et sec.
Si le boîtier est très sale, imbiber le chiffon dans de l’eau avec un peu de
détergent neutre, bien essorer le chiffon, puis essuyer le boîtier. Après le
nettoyage, sécher le boîtier à l’aide d’un chiffon sec.
Si un chiffon traité chimiquement est utilisé, lire les directives fournies avec
le chiffon avant de l’utiliser.
Ne pas essuyer la lentille avec un chiffon poussiéreux ou pelucheux.
Si de la poussière ou de la peluche se dépose sur la lentille, elle sera agrandie et
projetée sur l’écran. Utiliser une poire à air pour nettoyer toute poussière et
peluche de sur la surface de la lentille, ou utiliser un chiffon doux pour retirer toute
poussière ou peluche.
72
Remplacement du bloc de lampe
AVERTISSEMENT
Le bloc de lampe ne devrait être
remplacé que par un technicien
qualifié.
Lors du remplacement de la
lampe, la laisser refroidir pendant
au moins une heure avant de la
manipuler.
B Le couvercle de la lampe devient
très chaud, et on risque de se
brûler si on le touche.
Notes sur le
remplacement du bloc
de lampe
B Faire très attention en manipulant le
bloc de lampe retiré, car il contient du
gaz sous haute pression et peut
facilement s’endommager s’il est
cogné contre des objets durs ou s’il
tombe.
B La lampe produisant la lumière est en
verre; elle risque donc d’éclater si on
la laisse tomber ou si elle heurte des
objets durs. Faire bien attention en
manipulant la lampe.
B La lampe usagée qu’on a retirée
risque d’éclater si on la jette sans
prendre de précautions. Jeter la
lampe de la même manière qu’une
lampe fluorescente.
REMARQUE:
B Le projecteur n’est pas fourni
avec un bloc de lampe de
rechange. Demander les détails
au revendeur.Numéro de produit
du bloc de lampe: ET-LAE100
ATTENTION:
B Ne pas utiliser un bloc de lampe
avec un numéro de pièce autre
que celui indiqué ci-dessus.
Période de
remplacement du bloc
de lampe
La lampe est un produit qui doit être
remplacé. Même si la durée de vie
complète de l’ampoule n’est pas
encore épuisée, la luminosité de la
lampe diminuera progressivement. Il
faut donc remplacer périodiquement
la lampe.
L’intervalle de remplacement de la
lampe prévu est de 2000 heures; il
est toutefois possible qu’il faille
remplacer la lampe avant ce délai
en raison d’éléments variables tels
que les caractéristiques
particulières de la lampe, les
conditions d’utilisation et
l’environnement d’installation. Il est
recommandé de toujours avoir un
bloc de lampe de rechange prêt à
l’emploi. Une lampe qui a dépassé
la limite de 2000 heures d’utilisation
risque beaucoup plus d’exploser.
Afin d’éviter que la lampe explose,
celle-ci est éteinte automatiquement
lorsque la limite de 2000 heures
d’utilisation est atteinte.
REMARQUE:
B Les heures d’utilisation expliquées
ci-dessus concernent l’utilisation
effectuée lorsque le réglage
CHAUDE a été sélectionné pour
PUIS LAMPE dans le menu
OPTION. Si le réglage FROIDE est
sélectionné, la luminosité de la
lampe sera moindre et la durée de
vie de la lampe sera allongée.
B Bien que le délai de 2000 heures
soit l’intervalle de remplacement
prévu, l’obtention de cette durée
n’est pas couverte par la
garantie.
73
Others
À propos de la fente de carte mémoire SD
S’assurer qu’il n’y ait aucun objet étranger dans la fente lorsqu’on insère une carte
mémoire SD en option. Ces objets risqueraient d’endommager la carte et la fente.
À propos de l’écran
Si l’écran utilisé est sale, endommagé ou décoloré, des projections de bonne
qualité ne peuvent pas être obtenues. N’appliquer aucune substance volatile à
l’écran et ne pas le laisser se salir ou s’endommager.
A propos de la lampe
Il est possible qu’il faille remplacer la lampe plus tôt en raison de facteurs
variables tels que des caractéristiques de la lampe, des conditions d’utilisation et
un environnement d’installation particuliers, en particulier si elle est utilisée de
façon continue pendant plus de 10 heures.
À propos de l’affichage à cristaux liquides
L’affichage à cristaux liquides du projecteur est fabriqué en utilisant une
technologie de très haute précision permettant d’obtenir des images très
détaillées. Parfois, il est possible que des pixels non actifs apparaissent sur
l’écran sous forme de points fixes bleus, verts ou rouges.
Bien noter que ceci n’affecte pas le fonctionnement du LCD.
Avant de faire le nettoyage et l’entretien, s’assurer de
débrancher la fiche du cordon d’alimentation de la
prise de courant.
Essuyer le boîtier avec un tissu doux et sec.
Si le boîtier est très sale, imbiber le chiffon dans de l’eau avec un peu de
détergent neutre, bien essorer le chiffon, puis essuyer le boîtier. Après le
nettoyage, sécher le boîtier à l’aide d’un chiffon sec.
Si un chiffon traité chimiquement est utilisé, lire les directives fournies avec
le chiffon avant de l’utiliser.
Ne pas essuyer la lentille avec un chiffon poussiéreux ou pelucheux.
Si de la poussière ou de la peluche se dépose sur la lentille, elle sera agrandie et
projetée sur l’écran. Utiliser une poire à air pour nettoyer toute poussière et
peluche de sur la surface de la lentille, ou utiliser un chiffon doux pour retirer toute
poussière ou peluche.
72
Remplacement du bloc de lampe
AVERTISSEMENT
Le bloc de lampe ne devrait être
remplacé que par un technicien
qualifié.
Lors du remplacement de la
lampe, la laisser refroidir pendant
au moins une heure avant de la
manipuler.
B Le couvercle de la lampe devient
très chaud, et on risque de se
brûler si on le touche.
Notes sur le
remplacement du bloc
de lampe
B Faire très attention en manipulant le
bloc de lampe retiré, car il contient du
gaz sous haute pression et peut
facilement s’endommager s’il est
cogné contre des objets durs ou s’il
tombe.
B La lampe produisant la lumière est en
verre; elle risque donc d’éclater si on
la laisse tomber ou si elle heurte des
objets durs. Faire bien attention en
manipulant la lampe.
B La lampe usagée qu’on a retirée
risque d’éclater si on la jette sans
prendre de précautions. Jeter la
lampe de la même manière qu’une
lampe fluorescente.
REMARQUE:
B Le projecteur n’est pas fourni
avec un bloc de lampe de
rechange. Demander les détails
au revendeur.Numéro de produit
du bloc de lampe: ET-LAE100
ATTENTION:
B Ne pas utiliser un bloc de lampe
avec un numéro de pièce autre
que celui indiqué ci-dessus.
Période de
remplacement du bloc
de lampe
La lampe est un produit qui doit être
remplacé. Même si la durée de vie
complète de l’ampoule n’est pas
encore épuisée, la luminosité de la
lampe diminuera progressivement. Il
faut donc remplacer périodiquement
la lampe.
L’intervalle de remplacement de la
lampe prévu est de 2000 heures; il
est toutefois possible qu’il faille
remplacer la lampe avant ce délai
en raison d’éléments variables tels
que les caractéristiques
particulières de la lampe, les
conditions d’utilisation et
l’environnement d’installation. Il est
recommandé de toujours avoir un
bloc de lampe de rechange prêt à
l’emploi. Une lampe qui a dépassé
la limite de 2000 heures d’utilisation
risque beaucoup plus d’exploser.
Afin d’éviter que la lampe explose,
celle-ci est éteinte automatiquement
lorsque la limite de 2000 heures
d’utilisation est atteinte.
REMARQUE:
B Les heures d’utilisation expliquées
ci-dessus concernent l’utilisation
effectuée lorsque le réglage
CHAUDE a été sélectionné pour
PUIS LAMPE dans le menu
OPTION. Si le réglage FROIDE est
sélectionné, la luminosité de la
lampe sera moindre et la durée de
vie de la lampe sera allongée.
B Bien que le délai de 2000 heures
soit l’intervalle de remplacement
prévu, l’obtention de cette durée
n’est pas couverte par la
garantie.
73
Others
À propos de la fente de carte mémoire SD
S’assurer qu’il n’y ait aucun objet étranger dans la fente lorsqu’on insère une carte
mémoire SD en option. Ces objets risqueraient d’endommager la carte et la fente.
À propos de l’écran
Si l’écran utilisé est sale, endommagé ou décoloré, des projections de bonne
qualité ne peuvent pas être obtenues. N’appliquer aucune substance volatile à
l’écran et ne pas le laisser se salir ou s’endommager.
A propos de la lampe
Il est possible qu’il faille remplacer la lampe plus tôt en raison de facteurs
variables tels que des caractéristiques de la lampe, des conditions d’utilisation et
un environnement d’installation particuliers, en particulier si elle est utilisée de
façon continue pendant plus de 10 heures.
À propos de l’affichage à cristaux liquides
L’affichage à cristaux liquides du projecteur est fabriqué en utilisant une
technologie de très haute précision permettant d’obtenir des images très
détaillées. Parfois, il est possible que des pixels non actifs apparaissent sur
l’écran sous forme de points fixes bleus, verts ou rouges.
Bien noter que ceci n’affecte pas le fonctionnement du LCD.
Témoin d’alarme de
l’indicateur de la lampe
Affiché pendant 30
secondes. L’affichage
Plus de 1800 heures disparaît si l’on appuie sur
Le témoin s’allume en
n’importe quelle touche.
rouge même si le
projecteur est en mode
L’affichage
ne
peut
pas
Plus de 2000 heures
d’attente.
être
effacé,
quelle
que
(Le témoin s’éteint automatiquement
soit
la
touche
sur
environ dix minutes après qu’on ait
laquelle on appuie.
allumé l’appareil.)
Méthode de remplacement du bloc de lampe
REMARQUE:
B Si le temps d’utilisation de la lampe a dépassé 2000 heures (lorsque PUIS
LAMPE a été mis sur “CHAUDE”), le projecteur passe en mode d’attente
après environ dix minutes de fonctionnement. Dès lors, faire les étapes *
à - à la page suivante dans les 10 minutes.
# Mettre hors circuit
% Utiliser un tournevis Phillips
l’interrupteur d’alimentation
pour desserrer les deux vis de
principale (MAIN POWER)
fixation du bloc de lampe jusqu’à
suivant la méthode donnée
ce que les vis tournent librement.
dans “Mise hors circuit de
Tenir la poignée du bloc de
l’alimentation” à la page 23,
lampe et tirer doucement pour le
puis débrancher la fiche du
sortir du projecteur.
cordon d’alimentation de la
Vis de fixation du bloc de lampe
prise de courant et vérifier que
les pièces autour du bloc de
lampe se sont refroidies.
$ Utiliser un tournevis Phillips
pour desserrer les vis de
fixation du couvercle du bloc
de lampe sur le fond du
projecteur , puis enlever le
couvercle du bloc de lampe.
Poignée
Vis de fixation du
couvercle du bloc Couvercle de
l’unité de lampe
de lampe
74
& Insérer le nouveau bloc de
lampe tout en s’assurant que la
direction de l’insertion est
correcte, puis utiliser un
tournevis Phillips pour
resserrer fermement les vis de
fixation du bloc de lampe.
' Installer le couvercle du bloc de
lampe, puis utiliser un tournevis
Phillips pour resserrer
fermement les vis de fixation du
couvercle du bloc de lampe.
REMARQUE:
B S’assurer de bien installer le bloc
de lampe et le couvercle du bloc de
lampe. S’ils ne sont pas bien
installés, cela peut déclencher le
circuit de protection et le projecteur
ne pourra pas être allumé.
( Insérer la fiche du cordon
d’alimentation dans la prise de
courant, puis appuyer sur
l’interrupteur d’alimentation
principale (MAIN POWER).
REMARQUE:
B Si la touche d’alimentation (POWER)
sur le projecteur ne s’allume pas en
rouge quand l’interrupteur
d’alimentation principale (MAIN
POWER) est mis en circuit, remettre
hors circuit l’interrupteur
d’alimentation principale (MAIN
POWER) et vérifier que le bloc de
lampe et le couvercle du bloc de
lampe sont bien installés. Remettre
ensuite l’interrupteur d’alimentation
principale (MAIN POWER) en circuit.
) Appuyer sur la touche
d’alimentation (POWER) pour
projeter une image sur l’écran.
* Appuyer sur la touche de menu
(MENU) pour afficher l’écran de
MENU PRINCIPAL, puis
appuyer sur les touches F et
G pour déplacer le curseur et
sélectionner “OPTION”.
MENU
COR TRAP
IMAGE
POSITION
OBTURATEUR
VOLUME
LANGAGE
OPTION
MENU SD
SÉL.
VALID
EXIT
+ Appuyer sur la touche d’entrée
(ENTER) pour afficher le menu
OPTION, puis utiliser les
touches F et G pour
sélectionner DURÉE LAMPE.
OPTION
INFO ÉCRAN
OUI
NR
OUI
FORMAT
MODE 4:3
COULEUR FOND
NOIR
4:3 H.POS
CENTRE
INSTALLATION
FAÇADE
SOL/PLAFOND
SOL
VENTILATEUR
NORMAL
PUIS LAMPE
CHAUDE
DURÉE LAMPE
1820H
SÉL.
ESC
, Maintenir la touche d’entrée
(ENTER) enfoncée pendant
environ 3 secondes.
OPTION
INFO ÉCRAN
OUI
NR
OUI
FORMAT
MODE 4:3
COULEUR FOND
NOIR
4:3 H.POS
CENTRE
INSTALLATION
FAÇADE
SOL/PLAFOND
SOL
VENTILATEUR
NORMAL
PUIS LAMPE
CHAUDE
INIT COMPT [POWER OFF]
SÉL.
ESC
“DURÉE LAMPE” changera à
“INIT COMPT [POWER OFF]”.
REMARQUE:
B Si la touche de menu (MENU) est
pressée, l’écran de remise à zéro
de la durée de lampe sera
annulé.
- Couper l’alimentation
électrique. Le temps
d’utilisation total du bloc de
lampe est alors remis à zéro.
Pour plus de détails concernant
la mise hors tension, se
reporter à la page 23.
Others
Affichage à l’écran
75
Témoin d’alarme de
l’indicateur de la lampe
Affiché pendant 30
secondes. L’affichage
Plus de 1800 heures disparaît si l’on appuie sur
Le témoin s’allume en
n’importe quelle touche.
rouge même si le
projecteur est en mode
L’affichage
ne
peut
pas
Plus de 2000 heures
d’attente.
être
effacé,
quelle
que
(Le témoin s’éteint automatiquement
soit
la
touche
sur
environ dix minutes après qu’on ait
laquelle on appuie.
allumé l’appareil.)
Méthode de remplacement du bloc de lampe
REMARQUE:
B Si le temps d’utilisation de la lampe a dépassé 2000 heures (lorsque PUIS
LAMPE a été mis sur “CHAUDE”), le projecteur passe en mode d’attente
après environ dix minutes de fonctionnement. Dès lors, faire les étapes *
à - à la page suivante dans les 10 minutes.
# Mettre hors circuit
% Utiliser un tournevis Phillips
l’interrupteur d’alimentation
pour desserrer les deux vis de
principale (MAIN POWER)
fixation du bloc de lampe jusqu’à
suivant la méthode donnée
ce que les vis tournent librement.
dans “Mise hors circuit de
Tenir la poignée du bloc de
l’alimentation” à la page 23,
lampe et tirer doucement pour le
puis débrancher la fiche du
sortir du projecteur.
cordon d’alimentation de la
Vis de fixation du bloc de lampe
prise de courant et vérifier que
les pièces autour du bloc de
lampe se sont refroidies.
$ Utiliser un tournevis Phillips
pour desserrer les vis de
fixation du couvercle du bloc
de lampe sur le fond du
projecteur , puis enlever le
couvercle du bloc de lampe.
Poignée
Vis de fixation du
couvercle du bloc Couvercle de
l’unité de lampe
de lampe
74
& Insérer le nouveau bloc de
lampe tout en s’assurant que la
direction de l’insertion est
correcte, puis utiliser un
tournevis Phillips pour
resserrer fermement les vis de
fixation du bloc de lampe.
' Installer le couvercle du bloc de
lampe, puis utiliser un tournevis
Phillips pour resserrer
fermement les vis de fixation du
couvercle du bloc de lampe.
REMARQUE:
B S’assurer de bien installer le bloc
de lampe et le couvercle du bloc de
lampe. S’ils ne sont pas bien
installés, cela peut déclencher le
circuit de protection et le projecteur
ne pourra pas être allumé.
( Insérer la fiche du cordon
d’alimentation dans la prise de
courant, puis appuyer sur
l’interrupteur d’alimentation
principale (MAIN POWER).
REMARQUE:
B Si la touche d’alimentation (POWER)
sur le projecteur ne s’allume pas en
rouge quand l’interrupteur
d’alimentation principale (MAIN
POWER) est mis en circuit, remettre
hors circuit l’interrupteur
d’alimentation principale (MAIN
POWER) et vérifier que le bloc de
lampe et le couvercle du bloc de
lampe sont bien installés. Remettre
ensuite l’interrupteur d’alimentation
principale (MAIN POWER) en circuit.
) Appuyer sur la touche
d’alimentation (POWER) pour
projeter une image sur l’écran.
* Appuyer sur la touche de menu
(MENU) pour afficher l’écran de
MENU PRINCIPAL, puis
appuyer sur les touches F et
G pour déplacer le curseur et
sélectionner “OPTION”.
MENU
COR TRAP
IMAGE
POSITION
OBTURATEUR
VOLUME
LANGAGE
OPTION
MENU SD
SÉL.
VALID
EXIT
+ Appuyer sur la touche d’entrée
(ENTER) pour afficher le menu
OPTION, puis utiliser les
touches F et G pour
sélectionner DURÉE LAMPE.
OPTION
INFO ÉCRAN
OUI
NR
OUI
FORMAT
MODE 4:3
COULEUR FOND
NOIR
4:3 H.POS
CENTRE
INSTALLATION
FAÇADE
SOL/PLAFOND
SOL
VENTILATEUR
NORMAL
PUIS LAMPE
CHAUDE
DURÉE LAMPE
1820H
SÉL.
ESC
, Maintenir la touche d’entrée
(ENTER) enfoncée pendant
environ 3 secondes.
OPTION
INFO ÉCRAN
OUI
NR
OUI
FORMAT
MODE 4:3
COULEUR FOND
NOIR
4:3 H.POS
CENTRE
INSTALLATION
FAÇADE
SOL/PLAFOND
SOL
VENTILATEUR
NORMAL
PUIS LAMPE
CHAUDE
INIT COMPT [POWER OFF]
SÉL.
ESC
“DURÉE LAMPE” changera à
“INIT COMPT [POWER OFF]”.
REMARQUE:
B Si la touche de menu (MENU) est
pressée, l’écran de remise à zéro
de la durée de lampe sera
annulé.
- Couper l’alimentation
électrique. Le temps
d’utilisation total du bloc de
lampe est alors remis à zéro.
Pour plus de détails concernant
la mise hors tension, se
reporter à la page 23.
Others
Affichage à l’écran
75
These Operating Instructions are printed on recycled paper.
R
Professional/Industrial Video
Panasonic Broadcast & Television Systems Company
Division of Matsushita Electric Corporation of America
One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 392-4443
3330 Cahuenga Blvd West Los Angels, CA 90068 (323) 436-3500
Technical Support:
(800) 524-1448
(800) 526-6610
FAX: (201) 392-6514
E-Mail: pbtssupport@panasonic.com
Printed in Japan
S1202-1023B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising