инструкцию по установке видеоинтерфейсного адаптера для автомобилей Jaguar XF (1.8 Мб)

инструкцию по установке видеоинтерфейсного адаптера для автомобилей Jaguar XF (1.8 Мб)
GVIF08
Specification
carformer-b2b.ru +7 (495) 510-66-58
Contents
1. Before installation
1.1
1.2
1.3
1.4
1.5
Main specification
Features
System diagram
Components
Exterior
2. SETUP
2.1
2.2
2.3
2.4
2.5
DIP switch
Remote controller
OSD (on screen display)
FACTORY mode
Rear view parking guide line
3. Installation
3.1 Installation diagram
3.2 Cautions on installation
3.3 Connecting CAN cable
4. Troubleshooting
carformer-b2b.ru +7 (495) 510-66-58
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
1.1 Main Specification
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 3 x A/V Input (External video source).
-. 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
-. 1 x Analog RGB Input (Navigation System output)
-. 1 x LCD Input (Car system Input)
-. 1 x GVIF Input
2. Output Spec.
-. 1 x GVIF Output
-. 4 x Audio Select (12V power comes out from 4wires of cable by video, Navi mode)
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 6WATT, Max
4. Switch Input mode
- Input Video MUTE Function : Possible to make each input mute by operating Dip S/W.
- Possible to switch Input mode with Keypad
- Possible to switch Input mode with switch for source toggle
- Possible to switch mode through CAN
carformer-b2b.ru +7 (495) 510-66-58
3
1.2 Features
-Improved High-definition
-Support NTSC, PAL (Lexus is unavailable)
-AV & Navigation control via touching screen for an additional NAVI-SEL
(Only available on LAND ROVER)
-Remote controller offered
-Possible to move the displayed position of AV, Navigation.
-Able to run OSD menu without image displayed.
carformer-b2b.ru +7 (495) 510-66-58
4
1.3 System Diagram
Switch for source toggle
Remote Control
OEM NAVI Button
Navigation Input
(Analog RGB)
MCU
A/V1
DISPLAY
A/V2
A/V3
VIDEO
CIRCUIT
VIDEO MUX
Car Installation
OEM LCD
CVBS
(Rear Camera)
POWER
CIRCUIT
A/V
OUT
Car Screen Input
(Car Main Board)
Power Input
(+8VDC~+18VDC)
HEADREST
MONITOR
DIP S/W
carformer-b2b.ru +7 (495) 510-66-58
5
1.4 Components
LVDS IN cable * 1ea (Select)
IR cable * 1ea
LEXUS Original cable
MODE cable * 1ea
Main board * 1ea
LEXUS cable
Land Rover cable
Nissan/Infinity cable
AV cable * 1ea
POWER cable * 1ea
SEL cable * 1ea
RGB cable * 1ea
Remote control * 1ea
carformer-b2b.ru +7 (495) 510-66-58
6
1.5 Exterior
⑥
⑤
④
⑥
⑤
④
Dimension
Horizontal length 139mm
Vertical length 87mm
Height 24mm
① POWER/CAN/RGB
② SEL-OUT
③ AV(IN/OUT)
④ LVDS IN/OUT
⑤ DIP S/W
⑥ LED
①
②
①
②
③
③
carformer-b2b.ru +7 (495) 510-66-58
7
2.1 DIP switch
#PIN
function
DIP S/W selection
ON : Skipping RGB Mode
OFF : RGB Display
1
RGB INPUT MUTE
2
A/V 1 MUTE
ON : Skipping A/V 1
OFF : A/V1 Display
3
A/V 2 MUTE
ON : Skipping A/V 2
OFF : A/V2 Display
4
A/V 3 MUTE
ON : Skipping A/V 3
OFF : A/V3 Display
5
To select car
model
ON : Lexus
OFF : Land Rover
6
To select original
NAVI
7
Rear Mode
8
※ ON : DOWN, OFF : UP
※ DIP S/W usage
[LEXUS]
-Input mode to intend to use : MAIN + A/V3
-Rear view camera : installation on CVBS4
▷
▷
▷
▷
▷
▷
DIP
DIP
DIP
DIP
DIP
DIP
S/W
S/W
S/W
S/W
S/W
S/W
:
:
:
:
:
:
1,2,3 à ON (INPUT MODE SKIP)
4 à OFF (A/V3 available)
5 à ON
6 à OFF
7 à ON (CVBS4 available)
8 à OFF
ON : For using original NAVI
OFF : Not use original NAVI
ON : External Rear Camera
OFF : OEM Rear Camera
N.C
carformer-b2b.ru +7 (495) 510-66-58
8
2.2 Remote controller
Key
POWER & PIP
MENU
Function
Not for use
OSD implementation
OK
Making a selection
▲
Move upward
▼
Move downward
◀
Move leftward, press 2 seconds long-Factory
mode implementation
▶
Move rightward, press 2 seconds long-Factory
Mode implementation-Factory mode Reset
carformer-b2b.ru +7 (495) 510-66-58
9
2.3 OSD (on screen display)
OSD menu: Press ”MENU” button on the remote controller.
Analog RGB MODE
Video MODE
IMAGE
- BRIGHTNESS
- CONTRAST
- SATURATION
- HUE
- SHARPNESS
- USER IMAGE : To choose a option
among 4 prepared color shade.
Analog RGB MODE
Video MODE
OSD
- LANGUAGE : To change the language
displaying on navigation, DVD, CMMB OSD
menu (select 1 among English or Chinese)
- TRANS : Transparency control of the OSD
background
- H_POSITION : Horizontal movement of the
OSD window
- V_POSITION : Vertical movement of the
OSD window
Analog RGB MODE
Video MODE
UTIL
- FACTORY RESET : To reset all the
values about navigation, DVD screen
to factory default. (NOT available for
reset of the position value of images,
only for functions inside OSD menu)
carformer-b2b.ru +7 (495) 510-66-58
10
2.4 Factory mode
Factory mode: press ◀ button 2 seconds long.
IMAGE
-H_POSITION : Horizontal movement of the OSD window
-V_POSITION : Vertical movement of the OSD window
PARK
- PARK ENABLE : Setup of rear view parking guide line
- PARK SETUP : Control over position of rear view parking guide line.
(Refer to page 12)
- SAFE ENABLE : To select whether to use SAFE function (NOT to allow watch video
while driving) or not.
UTIL
-NAVI MODEL : KD680_NEW – for Chinese
NAV N GO – for Europe
-FACTORY RESET : To reset all the value in factory mode
carformer-b2b.ru +7 (495) 510-66-58
11
2.5 Rear view parking guide line
Factory mode: press ◀ button 2 seconds long.
① Register the value needed on the “PARK ENABLE” as “ON” in the PARK
section as shown left. (default – ON)
② If you get rear gear after setup, parking guide line will appear on screen as
shown left. Now that you push “OK” button, you can see “H-POS” on the left
of screen. Then adjust horizontal position of the guide line.
③ After adjusting horizontal position, press “OK” on the remote controller.
Then you can see “V-POS” on the left of screen. At that time you can adjust
vertical position of the guide line.
carformer-b2b.ru +7 (495) 510-66-58
12
3.1 Installation diagram
Original CAN
LED
Monitor
NAVI BOX
DIP S/W
LVDS IN/OUT
QVL-GF08-V7
SEL-OUT
POWER/CAN/RGB
CAN
AUX-ON (N.C)
REAR
OPT2 (N.C)
AV/OUT
AV3
AV2
AV1
REAR C
MODE : Toggle S/W
RGB
IR
PB12 (N.C)
GPIO-ZO : MMI
GND
ACC
Audio R
Audio L
Video
CAN-L
CAN-H
IR-AV3 (DTV)
IR-AV2 (DVD)
IR-AV1 (NAVI)
PARKING (SAFE)
REAR-SEL
AV1-SEL
NAVI-SEL
* Connect the Brown+Green wire of
CAN cable offered to Orange wire of
the car, the Green wire to Green wire
of the car like the above picture.
A/V(IN/OUT)
carformer-b2b.ru +7 (495) 510-66-58
13
3.2 Cautions on installation
§
Ignition key should be taken off before starting installation, interface power connection must be the last step in
installation.
§
Power cable should be separated when connecting interface.
§
Should be no any electronic devices or magnetic pole around installation place.
§
All steps of installation should be done by well-trained specialist.
§
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached label on
the board.)
§
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or
manufacturer.
§
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
carformer-b2b.ru +7 (495) 510-66-58
14
3.3 Connecting CAN cable
CAN-High
CAN-Low
POWER CABLE
* Connect the Brown+Green wire of CAN cable offered to Orange wire of the car,
the Green wire of CAN cable offered to Green wire of the car like the above picture.
carformer-b2b.ru +7 (495) 510-66-58
15
4. Troubleshooting
Q. I can not switch A/V sources.
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
Q. Displayed image color is not proper. (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform the manufacturer.)
Q. Rear camera image does NOT appear.
A. Set DIP switch #7 in “ON”
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform the manufacturer.
Q. Screen only displays white like left picture.
A. Check LCD out cable is connected well, if this status keeps, inform the manufacturer.
carformer-b2b.ru +7 (495) 510-66-58
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising