50mm

NOTE: before cutting countertop

Allow for handle clearance

63.5mm

FINISHED WALL / BACK SPLASH

CENTERLINE OF FITTING

CLIP LOCATIONS

329.3mm

RIM OF LAVATORY

K-2355

ARCHER

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

( 13 (1/2") )

·

·

·

BEFORE YOU BEGIN

·

Due to the nature of the installation, undercounter lavatories should be installed by trained and experienced installers.

Do not use adhesives or adhesive sealants with this product.

Inspect the waste and supply tubing; replace if necessary.

Prior to installation, unpack the new lavatory and inspect it for damage. Return the lavatory to its protective carton until you

·

· are ready to install it.

Observe all local plumbing and building codes.

Kohler lavatory is made according to American National Standard that it can match the American lavatory fittings . Any other lavatory fittings may not fit for kohler lavatory.

TOOLS AND MATERIALS

·

·

·

·

·

·

·

·

·

Sealant

Pencil

Tape measure

Sharp knife or scissors

Keyhole or saber saw

Drill (13mm(1/2") dia. drill bit or larger)

Safety glasses

Hammer

Rags or paper toweling

NOTE: You may require different, more specialized tools to install this lavatory to countertop materials other than wood or wood composites.

ROUGH-IN

389mm

356mm 333mm

249mm

498mm

29mm

11mm

191mm

3/8 Hot

1-1/4 Qutlet

102mm

3/8 Cold

64mm

192mm

76mm

610mm

256mm

813mm

864mm

203mm

Min

152mm

Max

686mm

Min

229mm

Min

Recommended ADA Installation

ADA

Note: Waterproof unprotected overhang area on the underside of wood counter.

(ASME)A112.19.2M

* K-8998 25

25

(1")

(1")

10mm

Sealant

Marble

16mm

Sealant

Wood

Installation

·

·

Roughing-In Notes

Fixture dimensions are nominal and conform to tolerances in ASME Standard A112.19.2M.

*Based on K-8998 with 25mm (1") of tailpiece exposed.

Supplied basin clamp assemblies require 25mm (1") minimum countertop thickness. Installer must supply anchors for thinner countertops.

(

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

(5/8")

VITREOUS CHINA UNDERCOUNTER LAVATORY

)

13 (1/2")

25 (1")

CUT-OUT TEMPLATE / INSTALLATION INSTRUCTION

10 (3/8") 16

Marble

Foam

Padding

Setting Tool

Anchor

INSTALL THE LAVATORY

NOTE: Install so future removal from underneath the countertop is possible to avoid damage to the

·

·

· countertop.

· Check the desired lavatory location for clearance between the backsplash, faucet, fixture, and cabinet.

·

·

Cut out the template.

Carefully position and trace the template on the countertop as directed on the template.

Mark the faucet hole centerline on the countertop.

Drill a 13mm(1/2") pilot hole on the inside of the cut line.

Cut out the countertop opening with a saber or keyhole saw.

FOR WOOD COUNTERTOPS

·

·

Mark and pre-drill the wood screw holes at the locations shown on the template.

Waterproof any exposed areas of wood.

FOR MARBLE COUNTERTOPS

·

Position the countertop upside down on foam padding to protect the surface. Mark and drill 10mm(3/8") holes

·

16mm(5/8") deep at the locations shown on the template.

Use a setting tool and hammer to secure the anchors.

Wood Screw

Clamp

Anchor Screw

A pply S ealant

FOR ALL INSTALLATIONS

· If the countertop has not been installed, install it at this time.

· Drill the faucet holes according to the faucet installation instructions.

· Install the faucet to the countertop according to the manufacturer s instructions.

· Install the drain to the lavatory according to the manufacturer s instructions.

NOTE: Do not use adhesives or adhesive sealants.

· Apply a continuous bead of quality sealant to the lavatory rim where it will contact the countertop.

NOTE: The screws provided should be used on countertops with a minimum 25mm(1") thickness. For thinner countertops, use appropriate anchors and fasteners.

· For wood, wood composite, and marble countertops, install the lavatory to the countertop with the clamps and screws provided. For other countertop materials, refer to the countertop manufacturer s instructions for

·

·

·

· recommended fasteners.

Position the lavatory squarely under the cutout before tightening the clamps. Draw the lavatory rim up to the countertop until it is snug.

Do not overtighten.

Immediately wipe away any excess sealant.

Make the final drain and faucet connections to complete the lavatory installation. Be sure to follow all instructions packed with the drain and faucet.

Clean up with a non-abrasive cleaner.

IMPORTANT CONSUMER

INFORMATION (CARE AND CLEANING)

To keep your lavatory looking new, make sure you rinse it out thoroughly after each use.

DO NOT USE ABRASIVES on this product, as they will scratch and ruin the surface. Stubborn stains, paint, or tar can be removed with turpentine or paint thinner.

6mm

CUT ALONG THIS LINE

NOTE: Using this template, the overhung is about 6mm. Customers can zoom the template by scale to meet their requirement.

443.6mm

106 2 324 200131

1080825-T01-A

117215-T01-C

ã

ã

, 2007

Copyright Kohler China Ltd., 2007