DX100 OPTIONS
INSTRUCTIONS
FOR ARM INTERFERENCE WITH SPECIFIED CUBIC AREA CHECK FUNCTION
Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain
for future reference.
MOTOMAN INSTRUCTIONS
MOTOMANINSTRUCTIONS
DX100 INSTRUCTIONS
DX100 OPERATOR’S MANUAL
DX100 MAINTENANCE MANUAL
The DX100 operator’s manual above corresponds to specific usage.
Be sure to use the appropriate manual.
Part Number: 159752-1CD
Revision: 0
YASKAWA ELECTRIC CORPORATION
MANUAL NO.
HW1480870
1/16
HW1480870
DX100
MANDATORY
•
This manual explains the arm interference with specified cubic area
check function of the DX100 system. Read this manual carefully
and be sure to understand its contents before handling the DX100.
•
General items related to safety are listed in Chapter 1: Safety of the
DX100 Instructions. To ensure correct and safe operation, carefully
read the DX100 Instructions before reading this manual.
CAUTION
•
The drawing in this manual are shown with the protective covers or
shields removed for clarity. Be sure all covers and shields are
replaced before operating this product.
•
The drawing and photos in this manual are representative examples
and differences may exist between them and the delivered product.
•
YASKAWA may modify this model without notice when necessary
due to product improvements, modifications, or changes in
specifications.
If such modification is made, the manual number will also be
revised.
•
If your copy of the manual is damaged or lost, contact a YASKAWA
representative to order a new copy. The representatives are listed
on the back cover. Be sure to tell the representative the manual
number listed on the front cover.
•
YASKAWA is not responsible for incidents arising from unauthorized
modification of its products. Unauthorized modification voids your
product’s warranty.
ii
HW1480870
2/16
HW1480870
DX100
Notes for Safe Operation
Read this manual carefully before installation, operation, maintenance, or
inspection of the DX100.
In this manual, the Notes for Safe Operation are classified as
“WARNING”, “CAUTION”, “MANDATORY”, or “PROHIBITED”.
WARNING
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
Indicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury to
personnel and damage to equipment.
It may also be used alert against
unsafe practice.
Always be sure to follow explicitly the
MANDATORY items listed under this heading.
PROHIBITED
Must never be performed.
Even items described as “CAUTION” may result in a serious accident in
some situations. At any rate, be sure to follow these important items.
NOTE
To ensure safe and efficient operation at all times, be sure
to follow all instructions, even if not designated as
“CAUTION” and “WARNING”.
iii
HW1480870
3/16
HW1480870
DX100
WARNING
•
Before operating the manipulator, check that servo power is turned
OFF pressing the emergency stop buttons on the front door of the
DX100 and the programming pendant.
When the servo power is turned OFF, the SERVO ON LED on the
programming pendant is turned OFF.
Injury or damage to machinery may result if the emergency stop circuit
cannot stop the manipulator during an emergency. The manipulator
should not be used if the emergency stop buttons do not function.
Fig. : Emergency Stop Button
•
Once the emergency stop button is released, clear the cell of all
items which could interfere with the operation of the manipulator.
Then turn the servo power ON.
Injury may result from unintentional or unexpected manipulator motion.
Fig. : Release of Emergency Stop
TURN
•
Observe the following precautions when performing teaching
operations within the P-point maximum envelope of the
manipulator:
– View the manipulator from the front whenever possible.
– Always follow the predetermined operating procedure.
– Keep in mind the emergency response measures against the
manipulator’s unexpected motion toward you.
– Ensure that you have a safe place to retreat in case of
emergency.
Improper or unintended manipulator operation may result in injury.
•
Confirm that no person is present in the P-point maximum envelope
of the manipulator and that you are in a safe location before:
– Turning ON the power for the DX100.
– Moving the manipulator with the programming pendant.
– Running the system in the check mode.
– Performing automatic operations.
Injury may result if anyone enters the P-point maximum envelope of the
manipulator during operation. Always press an emergency stop button
immediately if there is a problem.
The emergency stop buttons are located on the right of front door of the
DX100 and the programming pendant.
iv
HW1480870
4/16
HW1480870
DX100
CAUTION
•
Perform the following inspection procedures prior to conducting
manipulator teaching. If problems are found, repair them
immediately, and be sure that all other necessary processing has
been performed.
– Check for problems in manipulator movement.
– Check for damage to insulation and sheathing of external wires.
•
Always return the programming pendant to the hook on the cabinet
of the DX100 after use.
If the programming pendant is inadvertently left on the manipulator,
on a fixture, or on the floor, the manipulator or a tool may collide with
the programming pendant during manipulator movement, which may
result in personal injury or equipment damage.
•
Read and understand the Explanation of the Warning Labels in the
Setup manual before operating the manipulator.
Definition of Terms Used Often in This Manual
The MOTOMAN is the YASKAWA industrial robot product.
The MOTOMAN usually consists of the manipulator, the controller, the
programming pendant, and the manipulator cables.
In this manual, the equipment is designated as follows:
Equipment
Manual Designation
DX100 controller
DX100
DX100 programming pendant
Programming pendant
Cable between manipulator and DX100
Manipulator cables
v
HW1480870
5/16
HW1480870
DX100
Descriptions of the programming pendant, buttons, and displays are
shown as follows:
Equipment
Programming
pendant
Manual Designation
Character Keys
The keys which have characters printed on
them are denoted with [ ].
ex. [ENTER]
Symbol Keys
The keys which have a symbol printed on
them are not denoted with [ ] but depicted
with a small picture.
GO BACK
ex. page key
The cursor key is an exception, and a
picture is not shown.
PAGE
Axis Keys
Number Keys
“Axis Keys” and “Number Keys” are generic
names for the keys for axis operation and
number input.
Keys pressed
simultaneously
When two keys are to be pressed
simultaneously, the keys are shown with a
“+” sign between them, ex. [SHIFT] +
[COORD]
Displays
The menu displayed in the programming
pendant is denoted with { }.
ex. {JOB}
Description of the Operation Procedure
In the explanation of the operation procedure, the expression “Select • • •”
means that the cursor is moved to the object item and the SELECT key is
pressed, or that the item is directly selected by touching the screen.
Registered Trademark
In this manual, names of companies, corporations, or products are
trademarks, registered trademarks, or brand names for each company or
corporation. The indications of (R) and TM are omitted.
vi
HW1480870
6/16
HW1480870
DX100
Contents
1 Arm Interference with Specified Cubic Area Check Function ......................................................... 1-1
1.1 Outline of this Function ...................................................................................................... 1-1
1.2 Setting of Arm Interference with Specified Cubic Area Check Function............................ 1-2
1.2.1 Cubic Interference Area........................................................................................ 1-2
1.2.2 Tool Interfere File ................................................................................................. 1-5
1.2.3 Example of Setting Tool Interfere File .................................................................. 1-6
1.3 Recovery from Interference ............................................................................................... 1-7
1.3.1 Releasing Limit ..................................................................................................... 1-7
1.3.2 Editing Interference Area Setting While Alarming ................................................ 1-8
1.4 Notes ................................................................................................................................. 1-8
vii
HW1480870
7/16
HW1480870
1
1.1
DX100
1
Arm Interference with Specified Cubic Area Check Function
Outline of this Function
Arm Interference with Specified Cubic Area Check Function
1.1
Outline of this Function
The “check function of tool center point interferences with specified cubic
areas”, which is a standard feature of the DX100, turns ON the
corresponding its system output signals “#50080 to #50157:CUBE
INTERFERENCE Signal” when the tool center point interfered with
specified cubic areas.
Fig. 1-1: Tool Center Point Interference with Specified Cubic Area
Checks the tool center point intreference with
specified cubic interference areas
Cubic interference area
Cubic interference area
On the other hand, the “check function of arm interferences with specified
cubic areas”, turns ON the corresponding its system output signals
“#50080 to #50157:CUBE INTERFERENCE Signal” when the
manipulator’s arm including its tool center point interfered with specified
cubic areas.
Fig. 1-2: Arm Interference with Specified Cubic Area
Checks the arm including its tool interferences with
specified cubic intereference areas
1-1
HW1480870
8/16
HW1480870
1
1.2
DX100
1.2
1.2.1
Arm Interference with Specified Cubic Area Check Function
Setting of Arm Interference with Specified Cubic Area Check
Function
Setting of Arm Interference with Specified Cubic Area
Check Function
Cubic Interference Area
Up to 64 cubic interference areas can be registered. Of these 64, up to 8
areas can be registered as interference areas to the arm.
Fig. 1-3: Numbers of Cubic Interference Area
8 out of 64 cubic interference areas can be
registered as interference areas to the arm
The cubic interference areas are displayed by pressing
{Main Menu} → {ROBOT} → {INTEREFERENCE AREA}.
For the settings of the cubic interference area, refer to
”8.6.2 Cubic Interference Area” in “Chap 8 System Setup” of
“DX100 INSTRUCTIONS” (RE-CTO-A215).
On the cubic interference area setting window, display an
INTERFERENCE SIGNAL window to be the subject of the arm
interference with specified cubic areas check function.
Move the cursor key to the {MONITOR POSITION}.
Press [ENTER] to alternate “TOOL CENTER POINT” and “ENTIRE”.
Select “ENTIRE” and this interferences signal is set as one of the subject
cubic areas of the arm interference.
1-2
HW1480870
9/16
HW1480870
DX100
1
1.2
Arm Interference with Specified Cubic Area Check Function
Setting of Arm Interference with Specified Cubic Area Check
Function
NOTE
Out of 64 possible interference areas, 8 cubic interference
areas can be set to “ENTIRE” at “MONITOR POSITION” at
maximum. If more than 8 areas are tried to be set, the following alarm occurs.
ERORR 1510: Cannot edit. The maximum number of cubic
interference that is able to be set to “ENTIRE” is exceeded.
Under the condition that “ENTIRE” is set to “MONITOR
POSITION”, if 0.000[mm] is set as one of the cubic interference area side length, the DX100 will automatically regards
the length as 0.001[mm] to define the cubic interference
area. Then, it starts checking the interferences with the
arm.
For example, set an interference area with the length of
X-axis direction as 0.000[mm] and other directions follows.
<Max. value> <Min. value>
X:
NOTE
0.000[mm]
0.000[mm]
Y: 50.000[mm]
-50.000[mm]
Z: 50.000[mm]
-50.000[mm]
Taking the settings mentioned above, the DX100 will automatically define the cubic interference area as follows.
<Max. value> <Min. value>
X:
0.005[mm]
-0.005[mm]
Y: 50.000[mm]
-50.000[mm]
Z: 50.000[mm]
-50.000[mm]
1-3
HW1480870
10/16
HW1480870
DX100
1
1.2
Arm Interference with Specified Cubic Area Check Function
Setting of Arm Interference with Specified Cubic Area Check
Function
Set “ON” to {ALARM OUTPUT} after setting “ENTIRE” to {MONITOR
POSITION}. The following alarm occurs and the manipulator stops
immediately when the robot arm including the tool center point interferes
with the already specified cubic interference areas.
AL 4903: CUBE INTEREFERENCE (ENTIRE)
The alarm occurs only under the following conditions after
“ON” is set to {ALARM OUTPUT}.
NOTE
When the robot is operated by JOG operation or move
instruction.
However, the alarm would not occur when the manipulator
is already inside of the interference cubic area before setting “ON” to {ALARM OUTPUT}.
1-4
HW1480870
11/16
HW1480870
1
1.2
DX100
1.2.2
Arm Interference with Specified Cubic Area Check Function
Setting of Arm Interference with Specified Cubic Area Check
Function
Tool Interfere File
The manipulator’s tool part shape must be registered by the customer
because its tool shape varies depending on the work that the manipulator
performs. The shape can be registered with TOOL INTERFERE file.
Press {Main Menu} → {ROBOT} → {TOOL INTERFERENCE} to display
the TOOL INTERFERE file.
• A maximum of 64 tool interfere files, which is the same numbers as
the tool files, can be set.
The same numbered tool number and tool interference number are
allocated one-on-one.
In accordance with the tool number specified in the operation, a file
is selected out of 64 files.
• A maximum of 5 cylinders and spheres can be specified for registering the shape of the tool.
• Values for cylinders and spheres can be input to No.1 to No.5 by
moving the cursor key downward.
• Values input to Point 1 and 2 specify the either ends position of the
cylinder.
Like the setting of the tool dimensions, the setting values are set with
the center of T-axis flange regarded as the starting point (X=0, Y=0,
Z=0).
• The values input to “RADIUS” set the radius of the cylinders specified by Point 1 and 2. Also, the spheres with their center points at
Point 1 and 2 are set with their radius specified by the values input to
“RADIUS”.
1-5
HW1480870
12/16
HW1480870
Arm Interference with Specified Cubic Area Check Function
Setting of Arm Interference with Specified Cubic Area Check
Function
Example of Setting Tool Interfere File
140
50
2 Point1
1 Point1
85
Tool coordinate origin position
(T-axis flange face)
1 Point2
400
1.2.3
1
1.2
250
DX100
2 Point2
3 Point1
* No offset shall be set in Y direction.
3 Point2
1-6
HW1480870
13/16
HW1480870
1
1.3
DX100
1.3
Arm Interference with Specified Cubic Area Check Function
Recovery from Interference
Recovery from Interference
When {ALARM OUTPUT} is set to “ON” and {CHECK MEASURE} is set to
“FEED BACK”, still the alarm occurs if the manipulator interferes with the
interference area. Despite this alarm, the manipulator may not be put
outside of the interference area. It is because that the manipulator is still
inside of the area even after resetting the alarm and, furthermore, the
alarm occurs again. Then, it becomes impossible to reset the alarm any
more.
To put the manipulator outside of the interference area, refer to the
following procedures.
1.3.1
Releasing Limit
The alarm status mentioned above can be released on LIMIT RELEASE
window.
To display LIMIT RELEASE window, select {Main Menu} → {ROBOT} →
{LIMIT RELEASE}.
Move the cursor key to {CUBIC/AXIS INTERFERENCE RELEASE} and
press [SELECT] to alternate “VALID” and “INVALID”.
Monitoring of the interference can be released temporarily by setting
“VALID” to {CUBIC/AXIS INTERFERENCE RELEASE} only when the
mode is in teach mode.
However, {CUBIC/AXIS INTERFERENCE RELEASE} is set to “INVALID”
again automatically when the mode is changed to play mode or to remote
mode.
The user can release the alarm occurrence by following the procedures
below.
1. Select {Main Menu} → {ROBOT} → {LIMIT RELEASE}.
2. Change the setting of {CUBIC/AXIS INTERFERENCE RELEASE}
from “INVALID” to “VALID”.
3. Select {Main Menu} → {SYSTEM INFORMATION} → {ALARM}.
4. Press {ALARM RESET} button on the window.
5. Move the manipulator to outside of the interference area by JOG
operation.
6. Select {Main Menu} → {ROBOT} → {LIMIT RELEASE}.
1-7
HW1480870
14/16
HW1480870
1
1.4
DX100
Arm Interference with Specified Cubic Area Check Function
Notes
7. Change the setting of {CUBIC/AXIS INTERFERENCE RELEASE}
from “VALID” to “INVALID”.
1.3.2
Editing Interference Area Setting While Alarming
On the CUBIC/AXIS INTERFERENCE setting window, the interference
area can be edited even when the alarm is occurring.
The user can recover the manipulator from the alarm status by following
the procedure below.
1. Select {Main Menu} → {ROBOT} → {INTERFERENCE AREA}.
2. Display the interference area specified by the alarm number.
3. Change the setting of {ALARM OUTPUT} from “ON” to “OFF”.
4. Select {Main Menu} → {SYSTEM INFORMATION} → {ALARM}.
5. Press down “ALARM RESET” button.
6. Move the manipulator to outside of the interference area by JOG
operation.
7. Select {Main Menu} → {ROBOT} → {INTERFERENCE AREA}.
8. Change the setting of {ALARM OUTPUT} from “OFF” to “ON”.
1.4
Notes
1
When using the check function of arm interference with specified cubic
areas, to avoid any interferences with the manipulator including its tool,
set “COMMAND POSITION” to {CHECK MEASURE} on INTERFERENCE AREA window. Set the radius of the tool interfere file with allowances because there are position errors between the command position
and the feed back position for the moving manipulator.
2
Determine the setting value of the TOOL INTERFERE file in accordance
with the drawing.
1-8
HW1480870
15/16
DX100 OPTIONS
INSTRUCTIONS
ARM INTERFERE CHECK FUNCTION OPERATING INSTRUCTIONS
Specifications are subject to change without notice
for ongoing product modifications and improvements.
C Printed in Japan October 2011 11-10
YASKAWA ELECTRIC CORPORATION
MANUAL NO.
HW1480870
16/16
">
