MANUAL: EXTEND-A-GUN MODEL XG12 DANGER INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE

MANUAL:  EXTEND-A-GUN MODEL XG12 DANGER INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE
MANUAL: EXTEND-A-GUN
MODEL XG12
Telescoping Waterway for Deck Mounted Monitors
INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE
DANGER
Read instruction manual before use. Operation of this device without understanding the manual
and receiving proper training is a misuse of this equipment. A person who has not read and
understood all operating and safety instructions, is not qualified to operate the Extend-A-Gun
telescoping unit.
To make the Extend-A-Gun as versatile as
possible three mounting bracket kits are offered.
Each kit has a different upper bracket, the lower
bracket is the same in all three.
SHOWN WITH
TFT MASTER NOZZLE
AND CROSSFIRE DECK GUN
XGB-13 TUBE/SADDLE
BRACKET SET
3" NPT
XGB-23 PLATE/SADDLE
BRACKET SET
ALTERNATE:
1) MOUNTING PLATE, 9” SQ.
TFT PART XGB-23
2) SADDLE BRACKET
TFT PART XGB-33
XGB-33 SADDLE/SADDLE
BRACKET SET
** - OUTLETS SHOWN ARE
FOR MODELS XG12PL - XL & XG12-VL-XL
FOR MODELS WITH 3” MAKE NPT OUTLET, ADD 1”
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com
©Copyright Task Force Tips, Inc. 2002-2011
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219- 462-6161 • Fax 219-464-7155
LIX-512 July 25, 2011 Rev08
Table Of Contents
1.0 MEANING OF SIGNAL WORDS......................................... 3
2.0 SAFETY ............................................................................ 3
3.0 BRACKET SETS ................................................................. 4
3.1 MECHANICAL SPECIFICATIONS ................................ 4
3.2 PART IDENTIFICATION AND MODELS ............................. 5
3.3 PLATE BRACKET INSTALLATION ............................... 5
4.0 SIDE LOADS AT MOUNTING POINTS............................... 6
5.0 INDICATOR SWITCH WIRING ........................................... 7
6.0 LABELS ............................................................................ 8
7.0 MOUNTING MONITORS .................................................... 8
8.0 OPERATING INSTRUCTIONS ........................................... 8
8.1 EXTEND ....................................................................... 9
8.2 RETRACT ..................................................................... 9
8.3 INDICATOR LIGHT ....................................................... 9
9.0 EXPLODED VIEW & PARTS LIST .................................... 10
10.0 WARRANTY ...................................................BACK COVER
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefighting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefighting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
©Copyright Task Force Tips, Inc. 2002-2011
Fire and Emergency Manufactures and Service Association
P.O. Box 147, Lynnfield, MA 01940 • www.FEMSA.org
2
LIX-512 July 25, 2011 Rev08
1.0 MEANING OF SAFETY SIGNAL WORDS
A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI standard Z535.4-2007, the definitions of the four signal words are as follows:
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal injury.
2.0 SAFETY
The operation of this monitor can be dangerous. The following must be observed at all times.
DANGER
WARNING
WARNING
WARNING
When operating the Extend-A-Gun you may be in a precarious position. Watch your footing on top
of the truck. It can become very slippery. It is possible to fall off the truck onto the pavement.
The Extend-A-Gun may be used in either the raised or the lowered position, but not in-between.
Make sure that the slide bar is down and both pawls are flush with the housing before use. If the
word “UNLOCKED” is visible, the Extend-A-Gun is unlocked and may rise suddenly if it is in the
lowered position and the water is turned on or fall suddenly if it is in the raised position and the
water is turned off. When the pawls are flush with the housing, and the water is turned on, the
pawls are locked in position and prevent the latch mechanism from operating.
Do not plug or cap the Extend-A-Gun or mounted deck gun while it is in the raised position. This
will prevent the Extend-A-Gun from being lowered all the way and the latch pawls will not lock.
For safe dependable service, the Extend-A-Gun must be securely mounted.
WARNING
The forces acting on the mounting brackets, when the Extend-A-Gun is in the extended position,
are higher than the forces in a normal deck gun installation.
WARNING
Keep the upper and lower brackets as far apart as possible to minimize the amount of stress on
the upper and lower brackets.
WARNING
Master stream flows are very powerful and capable of causing injury and property damage. Make
sure the monitor is pointing in a safe direction before water to the monitor is turned on. Use care
in directing the stream.
CAUTION
Do not lift the slide bar when water is flowing, the mechanism will not unlatch, but the mechanism
can be damaged.
CAUTION
Do not lift the slide bar to lower the deck gun without supporting the weight of the deck gun. It
can fall and cause injury.
©Copyright Task Force Tips, Inc. 2002-2011
3
LIX-512 July 25, 2011 Rev08
3.0 BRACKET SETS
For safe dependable service, the Extend-A-Gun MUST be securely mounted. To make the Extend-A-Gun as versatile as possible,
three mounting bracket kits are offered. Each kit has a different upper bracket. The lower bracket is the same in all three.
WARNING
Task Force Tips strongly recommends that Extend-A-Gun be installed using the bracket sets,
sold by Task Force Tips, that are designed for this purpose. For the Extend-A-Gun to operate
safely and properly, it must be installed in such a way that the brackets can withstand the forces
resulting from the nozzle reaction force. The Task Force Tips bracket sets are designed to fit
the Extend-A-Gun outer tube very closely to prevent distortion of the outer tube and to give it
adequate support.
XGB-13
TUBE/SADDLE BRACKET SET
XGB-23
PLATE/SADDLE BRACKET SET
XGB-33
SADDLE/SADDLE BRACKET SET
3.1 MECHANICAL SPECIFICATIONS
QTY
PART
DESCRIPTION
4
VT37-16FNT
3/8-16 FLANGED HEX NUT
1
XG480
TUBE BRACKET
2
XG475
4-1/2 U-BOLT 3/8 DIA.
TUBE BRACKET WELDING
This kit contains a six inch square steel tube with two U-bolts to be used as the upper bracket and a saddle bracket, similar to a
heavy duty muffler clamp for the lower bracket. Both brackets must be used. This kit is designed primarily for installation in trucks as
they are being built at the factory. The tube bracket may be welded onto the truck tubular framework, as shown on the Tube Bracket
Welding Diagram. The lower bracket, as shown in the Saddle Bracket Welding Diagrams, should be welded to an additional support
and clamped as low at possible on the bottom of the Extend-A-Gun tube. Make sure the welds are capable of withstanding the forces
shown on the Side Loads At Mounting Points Diagram. The Extend-A-Gun may be installed in the brackets after the truck is painted.
Use Loctite, supplied in kit on U-bolt threads, and torque nuts on upper U-bolts to 15-17 ft-lbf, torque nuts on lower U-bolts to 36-40
ft-lbf.
©Copyright Task Force Tips, Inc. 2002-2011
4
LIX-512 July 25, 2011 Rev08
3.2 PART IDENTIFICATION AND MODELS
QTY
PART
DESCRIPTION
2
VT50-13NT
1/2-13 HEX NUT
1
XG486
SADDLE BRACKET
1
XG476
4-1/2 U-BOLT 1/2 DIA.
3.3 PLATE BRACKET INSTALLATION
This kit may be used in either new or retro-fit
installations. The top plate with its bracket may
be bolted above or below an existing deck. The
lower saddle bracket is installed as previously
shown. Both brackets must be used. To
minimize the stress on the brackets they should
be as far apart as possible when clamped to
the Extend-A-Gun tube. Please refer to the
Side Loads at Mounting Points Diagram and
make sure the mounting points can withstand
these forces. Use Loctite®, supplied in kit on
all threads, torque bolts to 40-45 ft-lbf and nuts
on U-bolts to 36-40 ft-lbf.
QTY
PART
DESCRIPTION
2
VT50-13NT
1/2-13 HEX NUT
1
XG485
MOUNTING PLATE
1
XG476
4-1/2 U-BOLT 1/2 DIA.
©Copyright Task Force Tips, Inc. 2002-2011
5
LIX-512 July 25, 2011 Rev08
4.0 SIDE LOADS AT MOUNTING POINTS
WARNING
Before installing the Extend-A-Gun you MUST determine the
be exerted in the proposed installation by the reaction force of the nozzle.
forces
that
will
1) Determine the distance, D1, in inches,
from the center of the monitor elevation joint
to the bottom of the threads in the monitor inlet.
D1 FOR MOST COMMON INSTALLATIONS
Task Force Tips CROSSFIRE
D1 = 1"
Elkhart Stinger Mod. 8297-98 w/ companion flange
D1 = 6"
Akron Apollo Mod. 3422 w/ companion flange
D1 = 5"
Akron Apollo Mod. 3422 threaded on
D1 = 4"
D1=
F1
inches
2) Locate the value of D1, in the charts on page 5.
Find the desired HEIGHT from the center of the
upper bracket to the center of the stream in the
HEIGHT column.
C Clamp
WHEN D2 IS LARGE AND D3 IS SMALL
THE REACTION FORCES, F1 & F2, ON
THE BRACKETS ARE LARGER.
D3
D2
15.7"
D1
3) Locate D2, the distance from the bottom of the latch
casting to the center of the upper mounting bracket,
for the choosen HEIGHT. (inches)
WHEN D2 IS SMALL AND D3 IS LARGE
THE REACTION FORCES, F1 & F2, ON
THE BRACKETS ARE SMALLER.
D2=
F2
inches
ALWAYS MAKE D3 AS LARGE AS POSSIBLE.
Crossfire
D1
1
D1
2
D1
3
Apollo Intergral Threads
D2
1
2
3
4
5
6
HEIGHT
18
19
20
21
22
23
D3 min
7
8
8
8
9
9
D3 max
14
13
12
11
10
9
D2
1
2
3
4
5
HEIGHT
19
20
21
22
23
D3 min
8
8
8
9
9
D3 max
14
13
12
11
10
D2
1
2
3
4
5
HEIGHT
20
21
22
23
24
D3 min
8
8
9
9
10
D3 max
14
13
12
11
10
©Copyright Task Force Tips, Inc. 2002-2011
D1
4
D2
1
2
3
4
5
HEIGHT
21
22
23
24
25
D3 min
8
9
9
10
10
D3 max
14
13
12
11
10
5
D2
1
2
3
4
HEIGHT
22
23
24
25
D3 min
9
9
10
10
D3 max
14
13
12
11
D3 min
9
10
10
11
D3 max
14
13
12
11
Stinger
D1
6
D2
1
2
3
4
HEIGHT
23
24
25
26
CHART FOR MODEL
XG-12 ONLY
6
7
D1
Apollo Flange
D1
D1
8
D1
9
D1
10
D2
1
2
3
4
HEIGHT
24
25
26
27
D3 min
10
10
11
11
D3 max
14
13
12
11
D2
1
2
3
4
HEIGHT
25
26
27
28
D3 min
10
11
11
11
D3 max
14
13
12
11
D2
1
2
3
HEIGHT
26
27
28
D3 min
11
11
11
D3 max
14
13
12
D2
1
2
3
HEIGHT
27
28
29
D3 min
11
11
12
D3 max
14
13
12
LIX-512 July 25, 2011 Rev08
4) Determine the distance, D3 in inches, from the center of the upper mounting
bracket to the center of the lower mounting bracket for the proposed installation. D3
MUST be between D3 min and D3 max.
D3=
inches
+ 15.7 = L
inches
5) Calculate forces on Brackets, Add D1 + D2 + D3 + 15.7 =
D1
+ D2
+ D3
6) Multiply L x 900
L
X 900 = M
inches • pounds
7) Divide M by D3
M
/D3
= F1
pounds
8) Subtract 900 from F1
F1
- 900 = F2
pounds
NOTE: F1 MUST be less than 3100 lbf. F2 MUST be less than 2200 lbf. And the proposed installation MUST be capable of
withstanding forces of this magnitude.
WARNING
Injury can result from an inadequately supported monitor. The monitor mount must be capable of
supporting the nozzle reaction force which can be as high as 900 lbf. (400 kg). Flanges and pipe
made from plastic are inadequate for monitor mounting and must not be used.
5.0 INDICATOR SWITCH WIRING
The Extend-A-Gun latch mechanism contains a magnetic switch. This switch is intended to be used with a MONITOR EXTENDED
warning light. The magnetic switch in the Extend-A-Gun is a normally open switch, and the switch is closed when the Extend-A-Gun
is in the down position. The enclosed relay MUST BE USED to limit the current through the switch.
87
86
MOUNT PANEL
LIGHT IN DASH
MOUNT RELAY ON
ELECTRICAL PANEL
1)
2)
3)
4)
5)
6)
87a
85
V4155 Relay 12VDC
15VDC Max
10 Watt Coil Max
EXTEND-A-GUN
SWITCH
30
BATTERY
SWITCH IS CLOSED WHEN
EXTEND-A-GUN IS IN THE DOWN POSITION
SPARE
CIRCUIT
BREAKERS
Screw the threaded switch body into the tapped hole in the Extend-A-Gun latch casting after the Extend-A-Gun is
permanently installed. Be careful not to twist or break the wires.
Mount the relay on the electrical panel with the terminals accessible.
Drill a 1/2” diameter hole in the dash board for the panel light. Leave enough room for a 1-13/16” diameter label around the
light or a 2” wide x 1-1/2” high label next to the light. Apply one of the two warning labels and push the panel light through the
hole in the dash.
Connect the labeled wires on the switch to terminal #85 on the relay and ground respectively.
Connect the terminals on the panel light to terminal #87A on the relay and ground respectively.
Connect a wire from a “spare” position on the trucks circuit breaker panel to terminals #30 and #86. The circuit from the “spare”
position in the fuse block should only be energized when the ignition switch is in the ON position.
©Copyright Task Force Tips, Inc. 2002-2011
7
LIX-512 July 25, 2011 Rev08
6.0 LABELS
WARNING
WARNING
Read manual before use.
INSTRUCTIONS
TASK FORCE TIPS, 3701 Innovation Way, Valparaiso, IN 46383-9327
+1 219 462-6161 • 800 348-2686 • www.tft.com • MADE IN U.S.A.
XGL025
EXTENDED.
Lower Before
Moving Vehicle.
XGL020
When Light is ON,
Deck Monitor is
1) Support weight of monitor.
2) Lift slide bar to disengage latch.
3) Raise or lower monitor, with slide bar released,
until latch engages.
4) Check that slide bar is fully down and latches
are flush with housing.
WARNING
When Light is ON,
Deck Monitor is
EXTENDED.
Lower Before
Moving Vehicle.
X GL010
Attach the rectangular instruction label (XGL010) to a smooth flat surface where it can be read by the person operating the Extenda-Gun and monitor.
Attach the warning label (XGL020) next to the indicator light or warning label (XGL025) around the indicator light on the truck
dashboard.
7.0 MOUNTING MONITORS
A Task Force Tips Crossfire® monitor may be mounted in one of two ways. We recommend that it be mounted directly on Extend-AGun models XG12PL-XL, XG12VL-XL, XG18PL-XL, or XG18VL-XL, which have integral Crossfire bases built in. Alternatively, it can
be mounted on Extend-A-Gun models XG12PL- PL, XG12VL-PL, XG18PL-PL, or XG18VL-PL using Task Force Tips part XFF-APL
Truck Mount Base, which fits only the Task Force Tips Crossfire.
Akron Apollo® monitors may be mounted on Extend-A-Gun models XG12PL-PL, XG12VL-PL, XG18PL-PL, or XG18VL-PL in one
of two ways. We recommend that the direct mount flange be screwed directly to the 3” pipe threads on the Extend-A-Gun. The base
may be modified by having the flange turned down to 5” diameter at your local machine shop. Alternatively, the direct mount flange
can be bolted to Task Force Tips part XFF-CPL Companion Flange (or equivalent) with out modification. Make sure that the flange
bolts do not interfere with the Extend-A-Gun latch mechanism.
Elkhart Stinger® monitors must be bolted to Extend-A-Gun models XG12PL-PL, XG12VL-PL, XG18PL-PL, or XG18VL-PL using
Task Force Tips part XFF-CPL Companion Flange (or equivalent). Make sure the flange bolts do not interfere with the Extend-A-Gun
latch mechanism.
CAUTION
The Extend-A-Gun may become damaged if it is allowed to freeze while containing water. Always
drain after use to avoid damage and possible loss of use.
8.0 OPERATING INSTRUCTIONS
WARNING
WARNING
The Extend-A-Gun may be used in either the extended or retracted position, but not in-between.
Make sure the slide bar is down and both pawls are flush with the housing before use. The word
“UNLOCKED” located on the top of the pawls should not be visible. When in use, the pawls are
locked in position and prevent the latch mechanism from operating.
Do not attempt to raise the Extend-A-Gun with water pressure. Rapid upward movement of the
Extend-A-Gun can cause injury to persons by striking them, or knocking them off the fire truck. It
can also cause damage to the Extend-A-Gun, monitor, or other equipment.
CAUTION
Do not lift the slide bar when flowing water. The mechanism will not unlatch, but the mechanism
can be damaged.
CAUTION
Do not lift the slide bar to lower the deck gun with out supporting the weight of the deck gun. It
can fall and cause injury.
©Copyright Task Force Tips, Inc. 2002-2011
8
LIX-512 July 25, 2011 Rev08
8.1 EXTEND
1)
Make certain the valve to the deck gun is closed.
2)
Lift the slide bar on the Extend-A-Gun latch mechanism with one hand and lift the deck gun straight up with your other hand. The
slide bar should be released after the deck gun has moved out of the retracted position. Notice the word “UNLOCKED” appear
on the top surface of the pawls.
3)
When the deck gun is in the extended position it will not be possible to lift it any higher. The pawls will retract, the slide bar will
move down flush with the housing and the word “UNLOCKED” is no longer visible.
4)
Make certain that the pawls are flush with the sides of the housing and that the word “UNLOCKED” is not visible before operating
the valve to the deck gun.
8.2 RETRACT
1)
Make certain the valve to the deck gun is closed.
2)
Lift the deck gun slightly with one hand to take the weight off the latch mechanism and lift the slide bar with your other hand.
Notice the word “UNLOCKED” appears on the top surface of the pawls.
3)
Lower the deck gun to the retracted position. The slide bar should be released after the deck gun leaves the extended
position.
4)
Make certain that both pawls are flush with the sides of the housing and that the word “UNLOCKED” is not visible before opening
the valve to the deck gun.
8.3 INDICATOR LIGHT
The Extend-A-Gun has a built in switch to control an indicator light on the truck dash board showing that the Extend-A-Gun is in the
the extended position. This is to help prevent damage that would occur if the deck gun hits a low overhanging object.. Do not move
the truck with the Extend-A-Gun in the extended position.
©Copyright Task Force Tips, Inc. 2002-2011
9
LIX-512 July 25, 2011 Rev08
9.0 EXPLODED VIEW AND PARTS LIST
33
34
35
1
40
43
44
45
46
6
4/5
10
19
13
17
18
42
20
37
36
11
12
13
14
15
41
16
27
21
28
30
31
22
32
23
©Copyright Task Force Tips, Inc. 2002-2011
24
26
25
25
10
LIX-512 July 25, 2011 Rev08
ITEM#
1*
DESCRIPTION
CROSSFIRE OUTLET
QTY
PART #
1
XGE390
12" INNER TUBE CODE-RLM
XG312XL
4/5
12" INNER TUBE 3" NPT
1
6
CYLINDRICAL MAGNET
1
10
CUP SEAL
1
XG125
11
RUBBER TERMINAL BOOT
1
VM4165
12
THREADED REED SWITCH
1
VM4144
13
STOP SCREW
2
XG120
14
SLIDE SPRING
2
XG141
15
FLUSH PIN
2
H790
16
SLIDE BAR
1
XG835
17
5/16-18 X 1-1/4 SOCKET HEAD SCREW
2
VT31-18SH1.2
18
ROLLER
2
XG130
19
BELL
1
XG110
RIGHT PAWL
1
XG135R
12" INNER TUBE 3" BSP
20
XG312PL
XG312BL
VM4152
LEFT PAWL (NOT SHOWN)
1
XG135L
21
SF WEARSTRIP
1
M515
22
12" OUTER TUBE
1
XG412
23
O-RING-343
1
VO-343
24
3" MALE NPT INLET
1
XG405PL
25
1/2-14 NPT PIPE PLUG
1
VT50-14PP
26
3" MALE VICTAULIC INLET
1
XG405VL
27
12 V SWITCHING RELAY
1
V4155
28
INSTRUCTION LABEL
1
XGL010
30
DASHBOARD LABEL
1
XGL020
31
INDICATOR LIGHT
1
VM4156
32
ROUND DASH LABEL
1
XGL025
33
SWIVEL RING
1
X425
34
5/16 SS BALL (39) PER REACE
78
VB.312
35
SWIVEL SCREW
2
X405
36
SWITCH PROTECTOR
1
XG115
37
1/4-20 X 1-1/4 SOCKET HEAD SCREW
1
VT25-20SH1.2
40
O-RING-236
1
VO-236
41
3/16 X 9/16 HDP SPIROL
2
V2005
42
XG WEAR PIN
2
XG252
43
3" MONITOR BASE CLAMP
2
Y4436
44
CYLINDER NUT
2
Y4437
45
WASHER
2
VW360X200-04
46
10-32 X 1 1/4 SOCKET HEAD SCREW
2
VT10-32SH1.2
* FOR CROSSFIRE ONLY
©Copyright Task Force Tips, Inc. 2002-2011
11
LIX-512 July 25, 2011 Rev08
10.0 WARRANTY
Task Force Tips, Inc., 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of its
Extend-A-Gun Telescoping Waterway (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from
defects in material and workmanship during the five (5) year period from the date of purchase.
TFT’s obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are shown by
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the
equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA, within a reasonable time after discovery of the
defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, it will correct the problem within a
reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is
an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANT ABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THE DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com
©Copyright Task Force Tips, Inc. 2002-2011
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219- 462-6161 • Fax 219-464-7155
LIX-512 July 25, 2011 Rev08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising