2006-z1-sport
© Marzocchi Suspension
2006 - Z1 Sport ETA
2006 - Z1 Sport ETA
Technical instructions
© Marzocchi Suspension
2006 - Z1 Sport ETA
Exploded view - Z1 Sport ETA - 130 TA
Rif. Code
1
1
1
2
3
4
5
7
8
11
21
22
23
25
25
25
27
28
33
36
38
41
42
43
50
53
54
55
56
57
58
59
60
63
63
63
63
63
63
63
64
65
66
67
67
68
69
71
73
74
75
77
78
79
80
80
81
82
83
85
87
818223/E
818223/A
818223/R
520278
549077AD
522244AA
524177
549072KR
528226
701211/C
523011
520313
5321130>B
547705
547707
547716
528243
703762KM/C
528046
547713
8031405/C
521142IW>A
528005
850939/C
522403>A
5141420/C
528223
523300
533297
523261
528230>A
538115
538114
5321261SU/R>A
5321261SV/R>A
5321261RS/R>A
5321261RR/R>A
5321261ST/R>A
5321261TI/R>A
5321261SR/R>A
520178PN
526145>A
850777/C
547685
547686
549067
5321129>A
805021
5181181
520341
5321153>A
850760/C
526143RX
520342AR
508995/C
508996CD/C
520349LA
5181224
701255/C
522387
512105
Quantity
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
Spare part list - Z1 Sport ETA - 130 TA
Rif.
Code
Description
Q.ty in the
model
1
818223/E
CROWN+STANCH+ALL.STEM Z150 FR
(replaces 818169/E)
1
1
818223/A
CROWN+STANCH+STEEL STEM Z150FR
(replaces 818169/A)
1
1
818223/R
CROWN+STANCH.TUBES Z150 FR 04
(replaces 818169/R)
1
2
520278
SCREW
1
3
549077AD
ETA/ECC BLACK ALUMINUM KNOB 04
1
4
522244AA
WASHER
1
5
524177
PISTON RING
1
7
549072KR
ALUMINUM RED KNOB
1
8
528226
O-RING
2
11
701211/C
PLUG UNIT
1
21
523011
STOP RING
1
22
520313
SCREW
1
23
5321130>B
FOOT NUT UNIT
1
25
547705
ALLOY STEM -LABELS
1
25
547707
ETA 06- LABEL
1
25
547716
VF2 LABEL
1
27
528243
O-RING
1
28
703762KM/C
ETA CART.-66 LIGHT'06 TR 150
1
33
528046
O-RING
2
36
547713
EXT.REBOUND ADJ.MTB'06 LABEL
1
38
8031405/C
PISTON ROD Z1 '06 TRAVEL 130
1
41
521142IW>A
NUT
1
42
528005
O-RING 2081
1
43
850939/C
SPRINGS KIT K=5
1
50
522403>A
WASHER
2
53
5141420/C
REB.SPRINGS 15MM KIT K=4.5
1
54
528223
O-RING
1
55
523300
STOP RING
1
56
533297
DUST SEAL DIA.32
2
57
523261
STOP RING
2
58
528230>A
OIL SEAL DIA.32
2
59
538115
UPPER BUSHING DIA.32
2
60
538114
LOWER BUSHING DIA.32
2
63
5321261SU/R>A
ANTI RADAR GREEN-TA MONOL.UNIT
1
63
5321261SV/R>A
DIRT BROWN- TA MONOLITE UNIT
1
63
5321261RS/R>A
ECO BLACK- TA MONOLITE UNIT
1
63
5321261RR/R>A
FLAT BLACK-TA MONOLITE UNIT
1
63
5321261ST/R>A
MAGNUM GREY FL-TA MONOL.UNIT
1
63
5321261TI/R>A
PURE WHITE MONOLITE UNIT
1
63
5321261SR/R>A
SILVER DUST- TA MONOLITE UNIT
1
64
520178PN
SCREW
2
65
526145>A
BUSHING
2
66
850777/C
QR 20 AXLE+SCREW KIT
1
67
547685
RH+LH Z1 SPORT'06-BLACK LABELS
1
67
547686
RH+LH Z1 SPORT'06-WHITE LABELS
1
68
549067
ADJUSTER
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
69
5321129>A
FOOT NUT UNIT
1
71
805021
FERRULE+ VALVE UNIT
1
73
5181181
PRELOAD SLEEVE 20MM LONG
1
74
520341
SCREW
1
75
5321153>A
CABLE GUIDE
1
77
850760/C
FENDER UNIT
1
78
526143RX
FENDER BUSHINGS
2
79
520342AR
FENDER SCREW
2
80
508995/C
REINFORCED ALLOY STEM+++
(replaces 508993/C)
1
80
508996CD/C
REINFORCED STEEL STEM 1 1/8
1
81
520349LA
AXLE SCREW -QR 20
1
82
5181224
PRELOAD SLEEVE
2
83
701255/C
ETA PLUG UNIT Z150 04
1
85
522387
WASHER
1
87
512105
FOOT BUFFER
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
Exploded view - Z1 Sport ETA - 150 TA
Rif. Code
1
1
1
2
3
4
5
7
8
11
21
22
23
25
25
25
27
28
33
36
38
41
42
43
50
53
54
55
56
57
58
59
60
63
63
63
63
63
63
63
64
65
66
67
67
68
69
71
74
75
77
78
79
80
80
81
82
83
84
85
87
Z1 Sport ETA - 150 TA - Oil levels
Position
Oil type
Quantity (cc)
Right fork leg SAE 7,5 - 550013
155
Left fork leg
155
SAE 7,5 - 550013
818223/E
818223/A
818223/R
520278
549077AD
522244AA
524177
549072KR
528226
701211/C
523011
520313
5321130>B
547705
547707
547716
528243
703700KM/C
528046
547713
8031405/C
521142IW>A
528005
850954/C
522403>A
5141420/C
528223
523300
533297
523261
528230>A
538115
538114
5321261SU/R>A
5321261SV/R>A
5321261RS/R>A
5321261RR/R>A
5321261ST/R>A
5321261TI/R>A
5321261SR/R>A
520178PN
526145>A
850777/C
547685
547686
549067
5321129>A
805021
520341
5321153>A
850760/C
526143RX
520342AR
508995/C
508996CD/C
520349LA
5181304
701255/C
5181224
522387
512105
Quantity
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
Spare part list - Z1 Sport ETA - 150 TA
Rif.
Code
Description
Q.ty in the
model
1
818223/E
CROWN+STANCH+ALL.STEM Z150 FR
(replaces 818169/E)
1
1
818223/A
CROWN+STANCH+STEEL STEM Z150FR
(replaces 818169/A)
1
1
818223/R
CROWN+STANCH.TUBES Z150 FR 04
(replaces 818169/R)
1
2
520278
SCREW
1
3
549077AD
ETA/ECC BLACK ALUMINUM KNOB 04
1
4
522244AA
WASHER
1
5
524177
PISTON RING
1
7
549072KR
ALUMINUM RED KNOB
1
8
528226
O-RING
2
11
701211/C
PLUG UNIT
1
21
523011
STOP RING
1
22
520313
SCREW
1
23
5321130>B
FOOT NUT UNIT
1
25
547705
ALLOY STEM -LABELS
1
25
547707
ETA 06- LABEL
1
25
547716
VF2 LABEL
1
27
528243
O-RING
1
28
703700KM/C
ETA CARTRIDGE Z150/04
1
33
528046
O-RING
2
36
547713
EXT.REBOUND ADJ.MTB'06 LABEL
1
38
8031405/C
PISTON ROD Z1 '06 TRAVEL 130
1
41
521142IW>A
NUT
1
42
528005
O-RING 2081
1
43
850954/C
SPRINGS KIT K=5,00
1
50
522403>A
WASHER
2
53
5141420/C
REB.SPRINGS 15MM KIT K=4.5
1
54
528223
O-RING
1
55
523300
STOP RING
1
56
533297
DUST SEAL DIA.32
2
57
523261
STOP RING
2
58
528230>A
OIL SEAL DIA.32
2
59
538115
UPPER BUSHING DIA.32
2
60
538114
LOWER BUSHING DIA.32
2
63
5321261SU/R>A
ANTI RADAR GREEN-TA MONOL.UNIT
1
63
5321261SV/R>A
DIRT BROWN- TA MONOLITE UNIT
1
63
5321261RS/R>A
ECO BLACK- TA MONOLITE UNIT
1
63
5321261RR/R>A
FLAT BLACK-TA MONOLITE UNIT
1
63
5321261ST/R>A
MAGNUM GREY FL-TA MONOL.UNIT
1
63
5321261TI/R>A
PURE WHITE MONOLITE UNIT
1
63
5321261SR/R>A
SILVER DUST- TA MONOLITE UNIT
1
64
520178PN
SCREW
2
65
526145>A
BUSHING
2
66
850777/C
QR 20 AXLE+SCREW KIT
1
67
547685
RH+LH Z1 SPORT'06-BLACK LABELS
1
67
547686
RH+LH Z1 SPORT'06-WHITE LABELS
1
68
549067
ADJUSTER
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
69
5321129>A
FOOT NUT UNIT
1
71
805021
FERRULE+ VALVE UNIT
1
74
520341
SCREW
1
75
5321153>A
CABLE GUIDE
1
77
850760/C
FENDER UNIT
1
78
526143RX
FENDER BUSHINGS
2
79
520342AR
FENDER SCREW
2
80
508995/C
REINFORCED ALLOY STEM+++
(replaces 508993/C)
1
80
508996CD/C
REINFORCED STEEL STEM 1 1/8
1
81
520349LA
AXLE SCREW -QR 20
1
82
5181304
SLEEVE 30MM
1
83
701255/C
ETA PLUG UNIT Z150 04
1
84
5181224
PRELOAD SLEEVE
1
85
522387
WASHER
1
87
512105
FOOT BUFFER
1
© Marzocchi Suspension
2006 - Z1 Sport ETA
Technical characteristics: Technical characteristics
Single-crown fork with ø 32mm legs.
Available travels: 130mm, 150 mm.
Right fork leg damping element: spring (air pre-load).
Left fork leg damping element: spring.
Right fork leg damping system: VF2 pumping element with external rebound adjustment.
Left fork leg damping system:ETA cartridge.
The stanchion tubes are pressed into the crown with a cryogenic process.
Lubrication and cooling of the parts subject to friction with a specially formulated oil.
Steer tube: steel or (optional) reinforced aluminium, 1-1/8", threadless.
Crown: aluminium alloy forged and CNC machined.
Stanchions: anodised aluminium.
One-piece assembly: made of magnesium alloy cast and CNC machined for lighter weight and more stiffness.
Sliding bushings: made of friction-free and wear-free material.
Seals: computer designed oil seals that guarantee maximum seal in any condition.
Oil: specially formulated oil that prevents foam and keeps the viscosity unchanged while offering high performance; free from static friction.
Dropout type: ø 20mm through-axle.
Disk brake mount: XC International Standard for 6" disk (fitting the special adapter supplied by the brake system manufacturer you can install the
8" disk).
Max wheel size: 2.8" x 26".
Integrated fender: available as optional.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Warnings: Instructions for use
MARZOCCHI forks are based on an advanced technology coming from the company’s years long experience in the professional mountain bike
industry.
For the best results, we recommend inspecting and cleaning the area below the dust seal and the stanchion tube after every use and lubricating the
parts with some silicone oil.
MARZOCCHI forks usually offer the best performances since the very first rides. Notwithstanding this, a short running-in period may be necessary
(5-10 hours) to adjust the internal couplings. This precaution will lengthen your fork’s life and guarantee its best performances.
We recommend changing the oil at least every 100 hours.
The forks with a polished finish must be treated periodically with polishing paste to keep the exterior shining like new.
Warnings: General safety rules
After disassembling the forks, always use new, original Marzocchi seals when reassembling.
To tighten two bolts or nuts that are near each other, always follow the sequence 1-2-1, and tighten to the required tightening torque.
Before reassembly, wash all new and old components and dry them with some compressed air, making sure there are neither breaks nor burrs.
Never use flammable or corrosive solvents when cleaning the forks, as these could damage the fork’s seals. If you must use a solvent, use
biodegradable detergents that are not corrosive, non-flammable, or have a high flash point.
Before reassembling, always lubricate those components that are in contact with the fork’s oil.
If you are planning not to use your forks for a long period of time, always lubricate those components that are in contact with the fork’s oil.
Always collect and keep any lubricants, solvents, or detergents, which are not completely biodegradable in the environment. These materials should
be kept in appropriate containers, and disposed of according to local laws.
Always grease the seal lips before reassembling.
All of the components of Marzocchi forks require the use of metric tools. Use only metric tools. Imperial (US) tools may have similar sizes, but can
damage the bolts, making them impossible to loosen or tighten.
When using a screwdriver to assemble or disassemble metal stop rings, O-rings, sliding bushings, or seal segments, avoid scratching or cutting the
components with the screwdriver tip.
Do not carry out any maintenance and / or adjustment operations that are not explained in this manual.
Only use original Marzocchi spare parts.
Before servicing the fork, we recommend washing the fork thoroughly.
Work in a clean, organized, and well-lit place. If possible, avoid servicing your forks outdoors.
Carefully check to see that your work area is free of dust and metal shavings from any component of the forks.
Never modify your fork in any way.
Warnings: Fitting the fork onto the frame
The fork is supplied with “A-Head Set” steer tube to be cut to size according to frame being used.
Fitting the fork onto the bike frame is a very delicate operation that must be carried out at one of our service centres only.
The assembling on the frame and the adjustment of the steer tube must be carried out following the instructions of the steering set manufacturer.
A wrong installation can be dangerous for the rider.
Marzocchi does not guarantee the assembly and accepts no liability for damage and/or accidents arising from a wrong
installation.
The steer tube must be pressed into the crown; its replacement must be carried out by one of our service centres using the adequate tools.
A wrong installation of the steer tube into the crown may cause the rider to lose the control of the bike and lead to serious
personal injury.
Warnings: Installing the disk brake
Installing the brake system is a delicate and critical operation that must be carried out by an authorized Marzocchi Service Center.
Marzocchi is not responsible for the installation and accepts no liability for damage and/or accidents arising from this operation.
Improper installation of a disk brake system can overstress the caliper mountings, which may cause the caliper mountings to break, resulting in loss
of control of the bicycle, an accident, personal injury, or death. Be sure that the brake system installation is also performed in strict compliance with
the instructions provided by the brake system manufacturer.
Improper installation can result in an accident, personal injury, or death.
Use only brake systems that comply with the forks specifications.
Make sure, after installation, that the brake cable of the brake system is correctly connected
to the proper mounting (A).
© Marzocchi Suspension
2006 - Z1 Sport ETA
The brake cable must never touch the crown and stanchions.
Warnings: Assembling the fender
The fender can be supplied with the fork or purchased separately.
Fender (1) must be assembled by placing the small support bush (2) between the screw and the fender
as shown and by tightening screws (3) with an 8mm fixed spanner to the recommended tightening torque
(6 Nm ±1).
Warnings: Assembling the wheel on forks with ø20mm through-axle
For a correct operation of the fork, install the wheel as explained below:
Align the center of the wheel with each wheel axle clamp.
Insert the wheel axle (1) through the right dropout, the wheel and the left dropout.
With the 6mm Allen wrench act on cap (2) and tighten the wheel axle to the recommended tightening
torque (15 Nm ± 1).
Check for the proper fork-wheel alignment. To do this, begin by fully compressing the fork a few times.
The wheel should not make contact with, or come close to any portion of the fork.
Then lift the front of the bicycle and spin the wheel a few times to verify the correct alignment with the
disk brake. The wheel should not wobble from side to side or up and down. Check the owner’s manual of
the brake system for the proper specifications.
With a 4mm Allen wrench, tighten the screws (3) on both dropouts to the recommended tightening
torque (6 Nm ± 1).
Dismantling: Removing the top caps
© Marzocchi Suspension
2006 - Z1 Sport ETA
Put the fork in the vice in vertical position, fixing it by the dropouts.
Dismantling: Removing the top right cap
Remove the protection cap (1).
Using a small pin screwdriver, blow the air off the fork leg, pushing on the air valve.
Fully unscrew lock cap (2) with a 21mm socket spanner.
Remove lock cap (2).
Dismantling: Removing the top left cap
With a 2mm Allen wrench loosen screw (4).
Remove first the screw (4), then the ETA control knob (5).
Fully unscrew lock cap (2) using a 21mm socket spanner.
Lift out lock cap (2).
Push washer (7) and the preload tube (8) downwards so you can reach locknut (6) with the 10mm
© Marzocchi Suspension
2006 - Z1 Sport ETA
spanner.
Holding locknut (6) with the 10mm spanner, use the 21mm spanner to unscrew lock cap (2) completely.
Remove lock cap (2).
Dismantling: Draining the oil
Remove the preload tube (1) and spring (3) from the right leg.
Remove washer (2), the preload tube (1) and spring (3) from the left leg.
Free the fork from the vice and tip it into a container of a suitable size to drain the oil; compress the fork
a few times to help the oil flow out.
Do not pour used oils on the ground.
Dismantling: Breaking down the steering crown unit / arch-slider assembly
Use the special spanner to remove the bottom nuts. Do not use other tools.
Turn the arch-slider assembly upside down.
With a 2mm Allen wrench loosen the screw (5) fixing the rebound adjustment knob (6) from the right leg.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Remove the rebound adjustment knob (6).
Using the special 12mm spanner (A), loosen the right bottom nut (7).
Pull out the bottom nut (7) complete with O-ring (8).
Take great care not to damage the O-ring on the pumping element rod.
Using the special 12mm spanner (A), loosen the left bottom nut (1).
Pull out the left bottom nut (1) complete with O-ring (2).
Pull the complete ETA cartridge (9) off the left leg.
Pull the crown-stanchion unit (3) off the arch-slider assembly (4).
© Marzocchi Suspension
2006 - Z1 Sport ETA
Dismantling: Dismantling the right pumping element and valve
Remove the bottom pad (1).
Using the special round-nose pliers, remove stop ring (2).
Pull out the pumping element (3) complete with rebound spring and valve.
Remove the complete valve group (4) from the pumping element.
Remove the preload tube (9) (only on models with 130mm travel).
Remove the rebound spring (7).
© Marzocchi Suspension
2006 - Z1 Sport ETA
If the piston segment (8) is damaged, you can prize it off with a small flat-tip screwdriver.
Dismantling: Dismantling the ETA cartridge
Loosen and remove nut (1) with a 10mm fixed spanner.
The ETA cartridge (5) has been sealed through machining and cannot be overhauled. In the
case of faults or a malfunctioning, this cartridge must be replaced.
Dismantling: Removing the seals
Prize the dust seal (1) off its seat with a small flat-tip screwdriver.
Take great care not to damage the internal surfaces of the one-piece assembly while
removing the dust seal.
With the same screwdriver, prize off the metal stop ring (2).
Take great care not to damage the internal surfaces of the one-piece assembly while
© Marzocchi Suspension
2006 - Z1 Sport ETA
removing the stop ring.
Protect the upper part of the slider with the special tool (A).
With a screwdriver, prize off the sealing ring (3).
Remove the sealing ring (3).
Take great care not to damage the internal surfaces of the one-piece assembly while
removing the sealing ring.
Remove the spring cup (4).
The old sealing rings and dust seals must not be used again.
Dismantling: Removing the guide bushes
Use the special extractor to remove the guide bushes. Do not use other tools.
Fit the aluminium bush (A) to the extractor keeping the side with larger diameter towards the edge
opposite to striker (D).
Fit the extraction washer (B) with a black finish to the extractor.
During use, remove the non-used washer from the extractor.
Remove first the top bushes, then the bottom bushes.
Fit the extraction washer keeping the blunt side towards the threaded grubscrew (C) fixed crosswise on to
the main rod as shown.
The slot in the rod lets the extraction washer swing inside the rod itself.
Insert the extractor in the arch-slider assembly from the side of washer (B) as shown.
The slot in the extractor rod will let the washer pass underneath the bush to be extracted.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Pull the extractor rod so that the upper face of the washer stops against the lower face of the guide bush.
Insert the aluminium bush (A) in the seat of the sealing ring.
While holding the main rod in position, the aluminium bush will drive the guide bushes during extraction.
Using striker (D) knock out and extract the guide bush (1).
Remove the guide bush (1) from the extractor.
Repeat the steps above to remove the bottom guide bush.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Assembling: Assembling the guide bushes
Insert the guide bushes using the special introducers (short type for the top bush and long type for the bottom bush, both with a
white finish). Do not use other tools.
Fit first the bottom bushes, then the top bushes.
Using the long introducer (A) fit the bottom bush (1).
Using a hammer knock the introducer (A) into the arch-slider assembly.
Using the short introducer (B) fit the top bush (2).
Using a hammer knock the introducer (B) into the arch-slider assembly.
Assembling: Assembling the seals
Insert the spring cup (4) in its seat.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Smear the dust seal and the sealing ring with some grease.
Insert the sealing ring (3) in its seat with the special introducer (A).
Using a hammer, knock in introducer (A) and drive the sealing ring home into the arch-slider assembly.
Using a small flat-tip screwdriver, fit the stop ring (2) and check that it fits perfectly into its groove.
Take great care not to damage the internal surfaces of the one-piece assembly when fitting
the stop ring.
The dust seals shall be refitted when reassembling the crown-stanchion unit / arch-slider assembly.
Assembling:
During the assembly of the pumping unit, strictly obey the instructions below.
Do not, at any times, reverse the position of the pumping elements in the fork legs (if you are unsure about anything, please refer
to the relevant exploded view).
Assembling: Assembling the ETA cartridge
Screw down nut (1) without tightening.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Assembling: Reassembling the steering crown unit / arch-slider assembly
A special spanner shall be used to assemble the bottom nuts. Do not, at any times, use other
tools.
Fit both dust seals (11) to the stanchions.
Insert the crown-stanchion unit (3) in the arch-slider assembly (4).
Insert the complete ETA cartridge (9) in the left leg.
With the special 12mm spanner (A), tighten the right bottom nut (7) complete with O-ring (8) to the
recommended tightening torque (10 Nm ± 1).
Fit the rebound adjusting knob (6) to the right leg.
Take great care not to damage the O-ring fitted to the end of the pumping element rod.
Tighten the fixing screw (5) of the adjusting knob to the recommended tightening torque (2 Nm ± 0.5).
© Marzocchi Suspension
2006 - Z1 Sport ETA
Using the special 12mm spanner, tighten the left bottom screw (1) complete with O-ring (2) to the
recommended tightening torque (10 Nm ± 1).
Using introducer (A) insert the dust seals (11) in their seats.
Assembling: Filling with oil
Block the fork in the vice, in perfectly vertical position.
Lower the crown-stanchion unit on the arch-slider assembly.
In a graduated recipient, prepare the quantity of oil to pour into the fork leg (see table).
Pour roughly 1/3 of the oil required into each stanchion, then pump the fork a few times to eliminate any
traces of air.
Pour the rest of oil in.
© Marzocchi Suspension
2006 - Z1 Sport ETA
A lower or higher volume or a type of oil other than the one recommended can change the behaviour of the fork in every phase.
Lift the crown-stanchion unit on the arch-slider assembly.
Insert spring (3) and the preload tube (1) in the right leg.
Insert spring (3), the preload tube (1) and washer (2) in the left leg.
Assembling: Mounting the top caps
Put the fork in the vice in vertical position, fixing it by the dropouts.
Assembling: Assembling the top right cap
Check that O-ring is not damaged.
Using the 21mm socket spanner, tighten cap (2) to the recommended tightening torque (10 Nm ± 1).
Restore the correct air pressure (see settings).
© Marzocchi Suspension
2006 - Z1 Sport ETA
Fit the protection cap (1).
Assembling: Assembling the top left cap
Screw the lock cap (2) down on the rod of the ETA cartridge without tightening being very careful not to
damage the O-ring.
Screw the lock cap (2) down on the rod of the ETA cartridge without tightening being very careful not to
damage the O-ring.
Push washer (7) and the preload tube (8) downwards so you can reach locknut (6) with a 10mm spanner.
Using the 10mm and 21mm spanners, tighten locknut (6) on cap (2) to the recommended tightening
torque (6 Nm ± 1).
With the 21mm socket spanner, tighten the lock cap (2) on the steering crown to the recommended
tightening torque (10 Nm ± 1).
Fit the ETA control knob (5) and screw (4).
Using a 2mm Allen wrench, tighten the knob fixing screw (4) to the recommended tightening torque (2
Nm ± 0.5).
© Marzocchi Suspension
2006 - Z1 Sport ETA
© Marzocchi Suspension
2006 - Z1 Sport ETA
Setting: General rules for calibration
By carefully calibrating the damping system you can get the maximum performance out of the same.
This paragraph indicates the sequence of operations to perform to set up the Marzocchi forks correctly.
In order to find the best settings for you, you will need to try several times to understand where and how to make adjustments. When doing so,
please ride in an open area, free from traffic, obstacles and other hazards.
The optimal setting is influenced by the geometry of the frame of the mountain bike, the weight of the cyclist, the type of terrain the bike will be
used on and the type of obstacles you have to deal with, but also by subjective factors associated with your riding style; therefore it is impossible to
provide objective data on the desired settings.
Nevertheless by carefully following the instructions below you will soon be able to find the optimal setting for you.
The shock absorber must be calibrated simply by using one adjuster at a time, following the order explained, noting the operations and any result
step-by-step.
During setting don't force the adjusters beyond their limit of travel and don't exceed the max recommended air pressure.
To keep the pressure inside the fork’s legs, only use the special MARZOCCHI pump with pressure gauge.
The use of any other pump can compromise the inflating operation and cause malfunction or damage to the fork, resulting in an
accident, personal injury or death.
Once the correct setting has been found, we recommend noting the number of clicks or turns of the adjuster with respect to the "fully closed"
position (adjuster fully clockwise) for a faster re-setting of your fork in case of need.
Setting: SAG
SAG means the fork bottoming under the biker's weight.
How to measure the SAG:
Follow these simple steps to measure the SAG.
On the leg portion of the fork, measure the distance between the lower crown and the dust seal (see
Picture A). Note this value as “H1”.
While sitting on the bike, repeat the measurement (see picture B). Note this value as “H2".
SAG = H1 - H2
How to find the best percent SAG:
The best percent SAG is 15-20% for Cross-country and All Mountain forks and 25-30% for Freeride and
Downhill forks.
In order to calculate the best SAG for your own fork, you will need to make the following calculation:
SAG = T x S (T = total travel; S = suggested sinking percentage).
Setting: Spring preload with air
The optimal spring preloading is the one that lets you obtain the desired SAG under the biker's weight.
Use the MARZOCCHI pump with pressure gauge to inflate the fork legs.
Using inadequate tools may lead to a wrong inflation and result in a malfunctioning or damage to the fork.
If you need to reduce the leg pressure, simply push the valve pin down with a pointed tool such as a small pin extractor.
Right fork leg:
To increase the pressure in the fork leg:
Remove the protection cap.
Tighten the threaded pump adapter on air valve.
Inflate till reaching the pressure you wish (see table).
Refit the protection cap.
© Marzocchi Suspension
2006 - Z1 Sport ETA
The pressure values in the table are given as a mere example and can be changed to meet the biker’s riding style and the track condition.
Setting: Rebound adjustment
Right fork leg:
With the rebound adjuster you can control the return speed of the fork after compression.
The right rebound speed setting makes the bike stable letting it follow the variations in the terrain and any obstacles.
If the fork setting is too reactive this will make the rear suspension instable and the mountain bike will have a tendency to snake. A too slow setting
however will cause problems when dealing with multiple obstacles where the suspension can't return to its fully extended position fast enough
between one obstacle and the next.
Turning adjuster (A) clockwise increases the hydraulic damping making the fork slower during the
rebound phase.
Turning adjuster (A) counter-clockwise decreases the hydraulic damping making the fork more reactive
during the rebound phase.
Do not force the adjuster beyond its limit of travel.
Setting: ETA
Left fork leg:
The ETA cartridge lets you adjust the rebound damping “on the fly” reducing the fork length down to a 30mm travel.
The control has two positions:
Pos: LOCK
Turning knob (A) clockwise activates the ETA cartridge function.
In this position, the fork legs stay down when hitting an obstacle; any other impact will lower the bike’s
geometry further.
This position is recommended to face steep and demanding uphills.
Pos: UNLOCK
Turning knob (A) counter-clockwise brings the fork back to normal function and deactivates the ETA
cartridge.
© Marzocchi Suspension
2006 - Z1 Sport ETA
NEVER use the "LOCK" position when riding on steep downhills. Failure to comply with these instructions could cause your fork
not to react safely enough when hitting an obstacle, resulting in a loss of control of the bicycle, damage and serious or lethal
injury.
© Marzocchi Suspension
2006 - Z1 Sport ETA
Tightening torques
Components
Tightening torque (Nm)
Adjuster locking screws
2±0,5
Fender fixing screws
6±1
Fork leg top caps
10±1
Pumping element/cartridge bottom nuts
10±1
Wheel axle Allen screws
6±1
Wheel axle screws
15±1
Air pressures
Preload air pressure
User weight
kg.
Air pressure
lb.
bar
psi
0 - 110+ 0 - 242 0 - 1,00 0,00 - 1.450,00
Z1 Sport ETA - 130 TA Z1 Sport ETA - 150 TA - Oil levels
Position
Oil type
Quantity (cc)
Right fork leg SAE 7,5 - 550013
155
Left fork leg
155
SAE 7,5 - 550013
© Marzocchi Suspension
2006 - Z1 Sport ETA
Diagnostics
Finding the problem
Finding the possible cause
Possible solutions proposed
Fork doesn't get full travel
Oil level too high
Check oil levels
Fork doesn't get full travel
Spring rate too stiff
Change to softer spring rate
Fork doesn't get full travel
Spring rate too stiff
Decrease air pressure
Fork extends too quickly; harsh top-out after
impacts
Rebound damping is not enough
Increase rebound damping
Fork extends too quickly; harsh top-out after
impacts
Rebound damping is not enough
Replace the oil (SAE 7.5) with one of higher
viscosity index
Fork has too much sag
Oil is too fluid
Check oil levels
Fork has too much sag
Spring rate too soft
Change to stiffer spring rate
Fork has too much sag
Spring rate too soft
Increase air pressure
Fork has too much sag
Spring rate too soft
Increase spring preload
Fork has too much sag
Spring rate too soft
Increase spring preload by replacing the preload
tube
Fork is “sticky”; fork does not perform as new
Dirty sealing rings; fork needs to be
serviced
Renew all seals
Fork is too soft, but the sag is the one
recommended
Compression damping is not enough
Increase compression damping by changing oil
volumes
Fork is too soft, needs more than the maximum
preload
Oil is too fluid
Check oil levels
Fork is too soft, needs more than the maximum
preload
Spring rate too soft
Change to stiffer spring rate
Fork is too soft, needs more than the maximum
preload
Spring rate too soft
Increase air pressure
Fork stays down or "packs up" during multiple
impacts
Rebound damping is too high
Decrease rebound damping with the relevant
register
Front wheel tends to tuck under while turning left
or right
Rebound damping is too high
Decrease rebound damping with the relevant
register
Front wheel tends to tuck under while turning left
or right
Spring rate too soft
Change to stiffer spring rate
Heavy amount of oil on stanchions; oil dripping
down legs
Sealing rings damaged
Renew all seals
Heavy amount of oil on stanchions; oil dripping
down legs
The stanchion tubes could be damaged
Have the stanchions be checked
Knocking sound during rebound, but no harsh topout
Rebound damping is too high
Decrease rebound damping with the relevant
register
Loss of sensitivity
Old oil
Change the oil
Loss of sensitivity
Sliding bushes worn
Renew the sliding bushes
Oil leaking from the bottom of the fork leg
Bottom nut/screw loose
Tighten the nut or screw
Oil ring on stanchions
Sealing rings dirty
Renew all seals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising