Manual 8468888

Manual 8468888
Top right
angle
Front
view
Right side
view
Left side
view
ZIPABOX
KNX MODULE
QUICK INSTALLATION GUIDE
v1.0
TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the
content of this manual, it is possible that this document may
contain technical inaccuracies, typographical, or other errors.
Zipato assumes no liability for any error in this publication, and for
damages, whether direct, indirect, incidental, and consequential
or otherwise, that may result from such error, including, but not
limited to loss of data or profits. Zipato provides this publication
“as is” without warranty of any kind, either express or implied,
including, but not limited to implied warranties of merchantability
or fitness for a particular purpose. The published information in
the manual is subject to change without notice. Zipato reserves
the right to make changes in the product design, layout, and driver
revisions without notification to its users. This version of the
Installation guide supersedes all previous versions.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies
with all the requirements in respect of interference radiation
according to EN 301 489-17, EN 301 489-1 and EN 300 328. The
connections conducting HF signals must neither be manipulated
nor damaged.
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer’s instructions. Be careful when using hand
and power tools and follow the manufacturer’s guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
DANGER
RISK OF ELECTROCUTION
All work on the device should only be carried out by trained and
skilled electricians. Observe the country-specific regulations.
CAUTION
The connected devices and the flush-mounted receiver can
become damaged if devices are operated that do not correspond
to the technical specifications (see technical data).
DANGER
RISK OF FATAL INJURY FROM ELECTRIC CURRENT.
The device has no basic insulation and must therefore be installed
in a way that protects against accidental contact.
DANGER
RISK OF FATAL INJURY FROM ELECTRIC CURRENT.
When installing a wall plate, the distance between the cover’s fixing
brackets or screws and the connections of the flush - mounted
MicroModule Switch Single must be at least 4 mm once installed.
If the distance is less than 4 mm, a deeper installation box must
be used. The fixing brackets or screws of the cover must not press
against the housing. Only insulated tools may be used for operation
on the device, e.g. an insulated phase tester.
make your home smart
PROTOCOL
INTRODUCTION
The Zipabox KNX Module serves as a simple integration
solution for KNX devices.
The device supports the BAOS protocol for accessing data
points. This allows KNX devices to be fully integrated into a
Zipato network via standard KNX bus.
COMPATIBILITY
This expansion module is designed to work only with Zipabox.
HANDLING
Frame Format: FT1.2 (IEC 870-5-1 and 870-5-2)
Protocol telegrams: EMI2
Protocol Data points: BAOS Binary V1
Up to 250 group objects and 250 parameters
CONNECTING DEVICE TO THE ZIPABOX
1 | Disconnect Zipabox from power;
2 | Align connector of KNX expansion module to expansion Slot 2 of
Zipabox (or to module connected into Slot 2);
3 | Join module and Zipabox together until gap between them is
completely closed.
1
Do not drop, knock or shake the module. Rough handling can break
internal circuit boards and connectors.
ENVIRONMENT
Do not expose the module to excessive heat or cold, as it can damage
or shorten the life of electronic circuit boards.
If possible, dispose this module at a recycling center.
Do not dispose of this module with the household waste.
SPECIFICATION
2
ELECTRICAL SAFETY
PROTECTION CLASSIFICATION (EN 60529)
SAFETY EXTRA LOW VOLTAGE
GALVANIC ISOLATION
IP 20
SELV DC 30 V
2,5 kV DC
EMC REQUIREMENTS
Complies with EN 50090-2-2 and EN 50491-5-2 CE norm
Complies with the EMC regulations (residential and functional
buildings) and low voltage directive Certification
KNX
ENVIRONMENTAL REQUIREMENTS
AMBIENT TEMP. OPERATING
AMBIENT TEMP. NON-OP.
REL. HUMIDITY (NON-CONDENSING)
- 5 ~ + 45 °C
- 25 ~ + 70 °C
5 % ~ 93 %
CONNECTING TO KNX NETWORK
Connect to the KNX network by using standard KNX bus (there is a
reverse polarity protection)
MECHANICAL DATA
Housing: Plastic
DIN rail mounted device, width: 18 mm
Weight: approx. 45 g Indicator
Signal-LED (green) for KNX-Connection Power supply
The device is supplied by KNX bus.
Current consumption: ca. 10 mA
CONNECTORS
KNX: KNX connector
www.zipato.com
ETS
ETS (Engineering Tool Software) is a manufacturer independent
configuration tool software to design and configure intelligent home
and building control installations with the KNX system. It is also
necessary for configuring the Zipato KNX expansion module. ETS
runs on computers using the Microsoft Windows System. It can be
downloaded from the KNX download page2. Version 4 suits fine for
working which the BAOS Module. A license is also necessary to run
make your home smart
ETS. The demo license allows only 3 devices per project. If more are
needed, we recommend to do the eCampus3 training to get a Lite
license which allows up to 20 devices.
VIA ETS THE FOLLOWING PARAMETERS CAN BE SET:
DATA POINTS
It’s possible to parameterize up to 250 data points. Every data point
can be allocated with a group address to send to bus. For receiving,
more group addresses can be allocated per object.
TYPE OF DATA POINTS
For every data point the type can be set. The following data point
types are selectable:
DPT 01 – Binary – 1 bit
DPT 02 – Binary controlled – 2 bits
DPT 03 – Dim up/down – 4 bits
DPT 04 – Character – 1 byte
DPT 05 – Scaling – 1 byte
DPT 06 – Signed value – 1 byte
DPT 07 – Unsigned value – 2 bytes
DPT 08 – Signed value – 2 bytes
DPT 09 – Float value – 2 bytes
DPT 10 – Time – 3 bytes
DPT 11 – Date – 3 bytes
DPT 12 – Unsigned value – 4 bytes
DPT 13 – Signed value – 4 bytes
DPT 14 – Float value – 4 bytes
DPT 15 – Access data – 4 bytes
DPT 17 – Scene – 1 byte
DPT 18 – Scene controlled – 1 byte
DPT – Unknown – 1 bit
DPT – Unknown – 2 bits
DPT – Unknown – 4 bits
DPT – Unknown – 6 bits
DPT – Unknown – 1 byte
DPT – Unknown – 2 bytes
DPT – Unknown – 3 bytes
DPT – Unknown – 4 bytes
ADDITIONAL TYPES FOR DATA POINTS 1 TO 32
DPT 16 – Character string – 14 bytes
DPT – Unknown – 6 bytes
DPT – Unknown – 8 bytes
DPT – Unknown – 10 bytes
DPT – Unknown – 14 bytes KNX Serial BAOS 870 (REG)
PARAMETER
KNX Serial BAOS 870 has 250 free programmable bytes, which can be
read via UART-Interface. The interpretation is performed by the client.
PARAMETER BYTE
For each one of the 250 bytes a value between 0 and 255 is
possible.
www.zipato.com
Select FILE/OPEN, and chose KNX project file from which you would
like extract ZIPATO BAOS 820 datapoints.
ZIPABOX
KNX MODULE
QUICK INSTALLATION GUIDE
v1.0
DESCRIPTION OF PARAMETER BYTE
For each parameter byte there is a label, which is not downloaded
in the device.
Select GROUP address which you would like to associate to the
Zipato network and add appropriate BAOS 820 DATAPOINT to it (in
this case we are adding ON/OFF datapoint)
Select EDIT/COPY to copy data to the clipboard, as you will PASTE it
to the Zipato dashboard to finish the proces of the integration.
ZIPATO DASHBOARD
Zipato dashboard is the main configuration tool for the Zipato
network. Go to my.zipato.com and login to your account by using
your username and password.
Import product database by using the link: http://www.weinzierl.
de/download/development/82x/ KNX_BAOS_870.zip and add KNX
BAOS module 820/870 from the list of devices to your network
Create Zipato endpoints by using appropriate datapoints. For each
Zipato ENDPOINT you need to select right BAOS endpoint. This
way, the newly createt Endpoint will communicate with the KNX
group addresses which are associated with those Enpoints. After
you finish adding the enpoints, press SAVE button and all your new
endpoints will be available within the Zipato network.
Select GROUP address which you would like to associate to the
Zipato network and add appropriate ZIPATO BAOS 820 DATAPOINT
to it (in this case we are adding ON/OFF STATUS datapoint)
Top
view
Open “ADD DEVICE” wizard and select KNX Device from the list
Select the KNX BAOS module 820/870 in the “topology list”, to see
all the associated objects
Export your project into a file which you can use to import associated
Endpoints to the Zipato KNX importer tool
Bottom
view
ZIPATO KNX IMPORTER TOOL
Light application that extracts group addresses and names associated
to the BAOS 820 datapoints. Download this tool at www.zipato.com
REPARING
Do not attempt to repair this product.
There are no user-serviceable parts inside.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics.
Select “Parameters” tab to manage Datapoints. For each datapoint
choose Type and add some description which will be helpful for the
later maintenance.
make your home smart
In the text field PASTE the date from the clipboard. If you lost the
datapoints from the clipboard, repeat the proces with the KNX
IMPORTER TOOL.
www.zipato.com
make your home smart
CLEANING
Use a dry cloth to clean this product. Do not use harsh chemicals,
cleaning solvents or strong detergents.
www.zipato.com
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS.
IN SUCH STATES OR COUNTRIES, SOME EXCLUSIONS OR
LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO
YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY
FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY. YOU
ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY
LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.
ZIPABOX
KNX MODULE
This Limited Product Warranty applies to ZIPATO branded hardware
products (collectively referred to as “ZIPATO Hardware Products”)
sold by ZIPATO (Europe), its European subsidiaries, affiliates,
authorized resellers, or country distributors (collectively referred to
as “ZIPATO Resellers”) with this Limited Product Warranty.
QUICK INSTALLATION GUIDE
v1.0
The term “ZIPATO Hardware Product” is limited to the hardware
components and all its internal components including firmware.
The term “ZIPATO Hardware Product” DOES NOT include any
software applications or programs.
MODELS AND FREQUENCIES
MODELS
EUROPEAN UNION - EU version
UNITED STATES - US version
RUSSIA - RU version
ISRAEL - IS version
AUSTRALIA - AU version
INDIA - IN version
FREQUENCIES
EUROPEAN UNION - EU
UNITED STATES - US
RUSSIA - RU
ISRAEL - IS
AUSTRALIA - AU
INDIA - IN
zbmknx.eu
zbmknx.us
zbmknx.ru
zbmknx.is
zbmknx.au
zbmknx.in
868.42 MHz
908.42MHz
869.02MHz
916.02MHz
921.42MHz
865.20MHz
LIMITED PRODUCT WARRANTY
GENERAL TERMS
Nothing in this Limited Product Warranty affects your statutory
rights as a consumer.
The Limited Product Warranty set forth below is given by Tri plus
grupa d.o.o. (Europe) (herein referred to as “ZIPATO”). This Limited
Product Warranty is only effective upon presentation of the proof
of purchase. Upon further request by ZIPATO, this warranty card
has to be presented, too.
EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,
ZIPATO MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. ZIPATO EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED
BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY
PERIOD. TO THE EXTENT ALLOWED BY LOCAL LAW, THE
REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S
SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO. THEY DO
NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU HAVE
AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM.
IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR
INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING
LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED
IN CONTRACT, TORT, OR OTHERWISE. HOWEVER, NOTHING
IN THIS AGREEMENT LIMITS ZIPATO’S LIABILITY TO YOU (I) IN
THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT
RESULTING FROM ZIPATO’S NEGLIGENCE, OR (II) TO THE EXTENT
RESULTING FROM ANY FRAUDULENT MISREPRESENTATION
ON THE PART OF ZIPATO, OR (III) TO THE EXTENT ARISING
UNDER PART 1 OF THE CONSUMER PROTECTION ACT 1987
OF THE UNITED KINGDOM. SOME STATES OR COUNTRIES DO
NOT ALLOW: (1) A DISCLAIMER OF IMPLIED WARRANTIES; (2)
A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS
OR THE EXCLUSION; OR (3) LIMITATION OF INCIDENTAL OR
make your home smart
GEOGRAPHICAL SCOPE OF THE LIMITED
PRODUCT WARRANTY
This Limited Product Warranty is applicable to Hardware Products
sold by Zipato Resellers in all countries listed at the beginning of
this document under the heading “Countries in which this ZIPATO
Limited Product Warranty applies”. The Limited Product Warranty
will be honored in any country where ZIPATO or its authorized service
providers offer warranty service subject to the terms and conditions
set forth in this Limited Product Warranty. However, warranty
service availability and response times may vary from country to
country and may also be subject to registration requirements.
LIMITATION OF PRODUCT WARRANTY
ZIPATO warrants that the products described below under
normal use are free from material defects in materials and
workmanship during the Limited Product Warranty Period set
forth below (“Limited Product Warranty Period”), if the product is
used and serviced in accordance with the user manual and other
documentation provided to the purchaser at the time of purchase
(or as amended from time to time).
ZIPATO does not warrant that the products will operate
uninterrupted or error-free or that all deficiencies, errors, defects
or non-conformities will be corrected.
This warranty shall not apply to problems resulting from: (a)
unauthorized alterations or attachments; (b) negligence, abuse
or misuse, including failure to operate the product in accordance
with specifications or interface requirements; (c) improper
handling; (d) failure of goods or services not obtained from ZIPATO
or not subject to a then-effective ZIPATO warranty or maintenance
agreement; (e) improper use or storage; or (f) fire, water, acts of
God or other catastrophic events. This warranty shall also not
apply to any particular product if any ZIPATO serial number has
been removed or defaced in any way.
ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A
RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR
THE ZIPATO HARDWARE PRODUCT.
LIMITED PRODUCT WARRANTY PERIOD
The Limited Product Warranty Period starts on the date of
purchase from ZIPATO. Your dated sales or delivery receipt,
showing the date of purchase of the product, is your proof of the
purchase date. You may be required to provide proof of purchase
as a condition of receiving warranty service. You are entitled to
warranty service according to the terms and conditions of this
document if a repair to your ZIPATO branded hardware is required
within the Limited Product Warranty Period.
[Other than in respect of products for domestic use (in particular
those listed in the first and last boxes in the table below), this
Limited Product Warranty extends only to the original end user
purchaser of this ZIPATO Hardware Product and is not transferable
to anyone who obtains ownership of the ZIPATO Hardware Product
from the original end-user purchaser.
www.zipato.com
PRODUCT WARRANTY PERIOD TABLE
PRODUCT TYPE
Zipabox KNX Module
PRODUCT WARRANTY
PERIOD
One (1) year
IMPORTANT
The content of “Product Type” listed above is subject to change;
please refer to the www.zipato.com for latest update.
PERFORMANCE OF THE LIMITED
PRODUCT WARRANTY
If a product defect occurs, ZIPATO’s sole obligation shall be to
repair or replace any defective Zipato Hardware Product free of
charge provided it is returned to an Authorized ZIPATO Service
Centre during the Limited Warranty Period. Such repair or
replacement will be rendered by ZIPATO at an Authorized ZIPATO
Service Centre. All component parts or hardware products that
are replaced under this Limited Product Warranty become the
property of ZIPATO. The replacement part or product takes on the
remaining Limited Warranty Period of the replaced part or product.
The replacement product need not be new or of an identical make,
model or part; ZIPATO may in its discretion replace the defective
product (or any part thereof) with any reconditioned equivalent (or
superior) product in all material respects to the defective product.
WARRANTOR
Tri plus grupa d.o.o.
Banjavciceva 11
10 000 Zagreb
CROATIA
TEL +385 (0)1 4004 404
FAX +385 (0)1 4004 405
DECLARATION OF CONFORMITY
The Manufacturer Tri plus grupa d.o.o. hereby declares that the
product:
Zipabox KNX Module (zbmknx)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
1 | this device may not cause harmful interference, and
2 | this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1 | l’appareil ne doit pas produire de brouillage, et
2 | l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE: Changes or modifications not expressly approved by Zipato
for compliance could void the user’s authority to operate the
equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
TECHNICAL SUPPORT
Having trouble installing your new product?
Zipato’s website contains the latest user documentation and
software updates for Zipato products and services.
www.zipato.com
CALL SUPPORT
In accordance with the following Directive(s): 2004/108/EC The Low
Voltage Directive, 2006/95/EC is in conformity with the applicable
requirements of the following documents:
CONTACT LINE
+385 (0)1 4004 404
(Mon-Fri) 9.00am-05.00pm (CET)
EN 60950-1:2007+A11:2009+A12:2011
EN 301 489-17 V2.1.1:2010
EN 301 489-3 V1..4.1:2003
EN 301 489-1 V1.8.1:2008
EN 300 328 V1.7.1:2008
EN 50130-4:1977+A1:2000+A2:2004
EN 300 220-1 V2.1.1:2006
EN 300 220-2 V2.1.2:2008
I hereby declare that the equipment named above has been
designed to comply with the relevant sections of the above
referenced specifications. The unit complies with all applicable
Essential Requirements of the Directives.
Person responsible for this declaration:
Dean Janacek, Certification Manager
18.09.2013
Changes or modifications not expressly approved Tri plus grupa
d.o.o. for compliance could void the user’s authority to operate the
equipment.
COPYRIGHT
© 2013 Tri plus grupa d.o.o. All Rights Reserved.
No part of this manual may be reproduced or transmitted in any form
without the expressed, written permission of Tri plus grupa d.o.o.
make your home smart
www.zipato.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising