Hardware Guide

Hardware Guide
HARDWARE INSTALLATION GUIDE
n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n
Table of Contents
Section 1
Safety Notice and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Section 2
Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Section 3
Electrical and General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Section 4
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Section 5
Unpacking the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Section 6A
Installing the Appliance in a 4‐Post Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Section 6B
Installing the Appliance in a 2‐Post Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Section 7
Rear Panel Connections and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Section 8
Front Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 2
1.
Safety Notice and Warnings
FCC Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
No Telecommunications Network Voltage (TNV)‐connected PCBs shall be installed.
This class A digital apparatus complies with Canadian ICES‐003.
Cet appareil numérique de la classe A est conforme à la norme NMB‐003 du Canada.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.
Environmental Warning
Perchlorate Material ‐ special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
This notice is required by California Code of Regulations, Title 22, Division 4.5, Chapter 33: Best Management
Practices for Perchlorate Materials. This product/part includes a battery that contains perchlorate material.
2.
Ratings
V: 100 ‐ 240 VAC (auto‐range)
Hz: 50 ‐ 60
A: 2.6 Max
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 3
3.
Electrical and General Safety Guidelines
CAUTION
This appliance is intended for installation in restricted areas only. Initial setup and maintenance
should be performed by qualified personnel.
CAUTION
Power down the appliance following the operating system’s proper power down procedure using the
power button on the front panel. Unplug the AC power cord before servicing.
CAUTION
To avoid electrical shock, check the power cords as follows:
• This product is to be installed in Restricted Access Location only.
• Use the exact type of power cords required.
• Use power cord(s) that came with safety certifications.
• Power cord(s) must comply with AC voltage requirements in your region.
• The power cord plug cap must have an electrical current rating that is at least 125% of the electrical
current rating of this product.
• The power cord plug cap that plugs into the AC receptacle on the power supply must be an IEC 320,
sheet C13,type female connector.
• Plug the power cord(s) into a socket that is properly grounded before turning on the power.
CAUTION
Required operating conditions for the appliance are ‐
• Temperature: 10 to 35oC (50 to 95oF).
• Humidity, non‐condensing: 8 to 90%.
DISPOSING OF BATTERY BACKUP UNITS - IF APPLICABLE
WARNING
If the BBU is damaged in any way, toxic chemicals may be released.
The material in the battery pack contains heavy metals that can contaminate the environment. Federal, state,
and local regulations prohibit the disposal of rechargeable batteries in public landfills. Be sure to recycle the old
battery packs properly. Comply with all applicable battery disposal and hazardous material handling laws and
regulations in the country or other jurisdiction where you are using the BBU.
WARNING
Risk of explosion if the battery is installed upside down or is replaced by an incorrect type.
Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the instructions.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 4
3.
Electrical and General Safety Guidelines (continued)
WARNING
Disconnect the power supply at the circuit breaker before accessing any components. Turning off the system
power supply switch does not reduce the risk of electrical shock from the power supply terminal block.
CAUTION
• To prevent the unit from overheating, never install the appliance in an enclosed area that is not properly
ventilated or cooled. For proper airflow, keep the front and back sides of the appliance clear of obstructions
and away from the exhaust of other equipment.
• Be aware of the locations of the power switches on the chassis and in the room, so you can disconnect
the power supply if an accident occurs.
• Take extra precautionary measures when working with high voltage components. Do not work alone.
• Before removing or installing main system components, be sure to disconnect the power first. Turn off
the system before you disconnect the power supply.
• Use only one hand when working with powered‐on electrical equipment to avoid possible electrical shock.
• Use rubber mats specifically designed as electrical insulators when working with computer systems.
• The power supply or power cord must include a grounding plug and must be plugged into grounded outlets.
CAUTION
Electric Static Discharge (ESD) can damage electronic components. To prevent damage to your system board,
it is important to handle it very carefully. The following measures can prevent ESD damage to critical components.
•
•
•
•
•
•
•
•
Use a grounded wrist strap designed to prevent static discharge.
Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready for use.
Touch a grounded metal object before removing the board from the antistatic bag.
Do not let components or PCBs come into contact with your clothing, which may retain a charge even if
you are wearing a wrist strap.
Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in use.
For grounding purposes, make sure your computer chassis provides excellent conductivity between
the power supply, the case, the mounting fasteners and the motherboard.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 5
4.
Site Preparation
Setup location, rack and appliance precautions
• Elevated Operating Ambient Temperature ‐ If installed in a closed or multi‐unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration
should be given to installing the equipment in an environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
Always keep the rack’s front door and all panels and components on the appliances closed when not servicing to
maintain proper cooling.
• Reduced Air Flow ‐ Installation of the equipment in a rack should be such that the amount of air flow required for
safe operation of the equipment is not compromised. Leave enough clearance, approximately 25 inches in the front,
and 30 inches in the back of the rack to enable you to access appliance components and allow for sufficient air flow.
• Mechanical Loading ‐ Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
ALL RACKS MUST BE MOUNTED SECURELY. Ensure that all leveling jacks or stabilizers are properly attached to the
rack. If installing multiple appliances in a rack, make sure the overall loading for each branch circuit does not exceed
the rated capacity.
Do not slide more than one appliance out from the rack at a time. Extending more than one appliance at a time may
result in the rack becoming unstable. Install your appliance in the lower part of the rack because of its weight and
also for ease in accessing appliance components.
• Circuit Overloading ‐ Consideration should be given to the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
• Reliable Earthing ‐ Reliable earthing of rack‐mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Install near appropriate AC outlets, and Ethernet hubs or individual jacks. Be sure to install an AC Power Disconnect
for the entire rack assembly. The Power Disconnect must be clearly marked. Ground the rack assembly properly to
avoid electrical shock.
5.
Unpacking the Appliance
Before you begin:
Verify that the ship kit includes a power cord, the screws and the rack clips (shown below) that you will need
to install the appliance in your rack.
4-POST RACK
Four (4) M6 x 16 mm
Phillips Pan Head Screws
Front view
Side view
2-POST RACK
Four (4) Rack Clips
Front view
Side view
Rear view
Four (4) M5 x 12 Phillips Flat Head Screws
and Four (4) M5 x 12 Cone Washers
Front view
Side view
Cone washer
NOTE: Use the hardware supplied with your specific rack if different from the hardware supplied in this kit.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 6
6A. Installing the Appliance in a 4‐Post Rack
Step 1
• Install two rack clips into the top and
bottom of three holes on each side in
the rack as shown. The tabs on each
should be on the top and bottom to
help stabilize them in the holes. No
tools are needed to install the clips,
firmly press them into place
• Make sure the clips are level in height
on the left and right sides for proper
alignment to allow accurate appliance
installation.
4-Post Rack
Install two
rack clips in
the top and
bottom of
three holes
Leave
middle hole
empty
Step 2
• Install the appliance in the rack as
shown. Insert one M6 x 16 screw*
through the top and bottom holes
in the ears into the rack clips on each
side of the rack.
*NOTE: Refer to your rack’s mounting
hardware for the proper size and type of
screws to secure the appliance in the rack.
Two (2) M6 x 16 pan he
ad screws
head
ach side*
on eeach
• Tighten each screw to secure the
appliance in the rack.
4-Post Rack
NOTE: When installing (or removing)
the appliance from the rack make sure to
support the unit at all times.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 7
6B. Installing the Appliance in a 2‐Post Rack
Step 1
• Install the appliance in the 2‐post
rack as shown. Insert one M5 x 12
screw* and one M5 x 12 cone washer*
through the top and bottom holes
in the ears on each side into the
threaded holes in the rack.
*NOTE: Refer to your rack’s mounting
hardware for the proper size and type of
screws to secure the appliance in the rack.
ddǁŽ;ϮͿDϱdžϭϮŇĂƚŚĞĂĚƐĐƌĞǁƐ
ǁŽ;ϮͿDϱdžϭϮŇĂƚŚĞĂĚƐĐƌĞǁƐ
ĂĂŶĚƚǁŽĐŽŶĞǁĂƐŚĞƌƐŽŶĞĂĐŚƐŝĚĞ
ŶĚƚǁŽĐŽŶĞǁĂƐŚĞƌƐŽŶĞĂĐŚƐŝĚĞ*
ϮͲWŽƐƚZĂĐŬ
Ϯ
ͲWŽƐƚZĂĐŬ
• Tighten each screw to secure the
appliance in the rack.
NOTE: When installing (or removing)
the appliance from the rack make sure to
support the unit at all times.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 8
7.
Rear Panel Connections and Cabling
CAUTION
Slide rail/mounted equipment is not
to be used as a shelf or a work space.
A
B
C
D
J
E
F
G
M
N
O
H
L
I
K
P
A
Power Supply Module Fan
G
LAN Port 6
M
LAN Port 2
B
Power Supply AC Inlet
H
PCI Card Expansion Slot
N
LAN Port 4
C
COM Port
I
USB Port 6
O
LAN Port 7
D
IPMI or LAN Port 5
J
USB Port 7
P
VGA Port
E
LAN Port 1
K
USB Port 2
F
LAN Port 3
L
USB Port 3
1
3
2
1
Step 1
Connect the power cord.
Step 2
Connect the Ethernet cables.
Step 3
Connect any other required cables.
2
Proceed to Section 8, Front Panel Operation on page 10.
Telemate.Net Software / 15R Hardware Installation Guide for NetSpective
Page 9
8.
Front Panel Operation
Power on the Appliance:
Press the I/O Power Button located on the far right
of the front panel.
NIC2
NIC2 LED
Overheat
Overheat
Fan
Fan FFail
ail LED
HDD LED
NIC1
NIC1 LED
ZĞƐĞƚƵƩŽŶ
ZĞƐĞƚƵƩŽŶ
Power
Power LED
I/O Power
Power
ƵƩŽŶ
ƵƩŽŶ
5555 Triangle Parkway
Suite 150
Norcross, GA 30092
US and Canada: +1.678.589.7100
Fax: +1.678.589.7110
www.telemate.net
© 2015 TeleMate.Net Software. All rights reserved. No part of this publication, including text, examples, diagrams, or icons, may be reproduced, transmitted, disclosed or translated in any
form or by any means, electronic, mechanical,manual, optical or otherwise, for any purpose, without prior written permission of TeleMate.Net Software. Information in this publication is
subject to change without prior notification. TeleMate.Net Software may have patents or pending patents applications, trademarks, copyrights, or other intellectual property rights covering
subject matter in this publication. The furnishing of this document does not give you license to these patents, trademarks, copyrights, or other intellectual property. Specifications are subject
to change without prior notification.
NetSpective is a registered trademark of TeleMate.Net Software in the United States and other jurisdictions. All other trademarks, registered trademarks and service marks are the property
of their respective owners
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising